3 files changed, 19 insertions, 67 deletions

diff --git a/arch/arm/plat-pxa/include/plat/gpio.h b/arch/arm/plat-pxa/include/plat/gpio.h
deleted file mode 100644
index 1ddd2b97a729..000000000000
--- a/arch/arm/plat-pxa/include/plat/gpio.h
+++ /dev/null
@@ -1,64 +0,0 @@
-#ifndef __PLAT_GPIO_H
-#define __PLAT_GPIO_H
-
-struct irq_data;
-
-/*
- * We handle the GPIOs by banks, each bank covers up to 32 GPIOs with
- * one set of registers. The register offsets are organized below:
- *
- *           GPLR    GPDR    GPSR    GPCR    GRER    GFER    GEDR
- * BANK 0 - 0x0000  0x000C  0x0018  0x0024  0x0030  0x003C  0x0048
- * BANK 1 - 0x0004  0x0010  0x001C  0x0028  0x0034  0x0040  0x004C
- * BANK 2 - 0x0008  0x0014  0x0020  0x002C  0x0038  0x0044  0x0050
- *
- * BANK 3 - 0x0100  0x010C  0x0118  0x0124  0x0130  0x013C  0x0148
- * BANK 4 - 0x0104  0x0110  0x011C  0x0128  0x0134  0x0140  0x014C
- * BANK 5 - 0x0108  0x0114  0x0120  0x012C  0x0138  0x0144  0x0150
- *
- * NOTE:
- *   BANK 3 is only available on PXA27x and later processors.
- *   BANK 4 and 5 are only available on PXA935
- */
-
-#define GPIO_BANK(n)	(GPIO_REGS_VIRT + BANK_OFF(n))
-
-#define GPLR_OFFSET	0x00
-#define GPDR_OFFSET	0x0C
-#define GPSR_OFFSET	0x18
-#define GPCR_OFFSET	0x24
-#define GRER_OFFSET	0x30
-#define GFER_OFFSET	0x3C
-#define GEDR_OFFSET	0x48
-
-static inline int gpio_get_value(unsigned gpio)
-{
-	if (__builtin_constant_p(gpio) && (gpio < NR_BUILTIN_GPIO))
-		return GPLR(gpio) & GPIO_bit(gpio);
-	else
-		return __gpio_get_value(gpio);
-}
-
-static inline void gpio_set_value(unsigned gpio, int value)
-{
-	if (__builtin_constant_p(gpio) && (gpio < NR_BUILTIN_GPIO)) {
-		if (value)
-			GPSR(gpio) = GPIO_bit(gpio);
-		else
-			GPCR(gpio) = GPIO_bit(gpio);
-	} else
-		__gpio_set_value(gpio, value);
-}
-
-#define gpio_cansleep		__gpio_cansleep
-
-/* NOTE: some PXAs have fewer on-chip GPIOs (like PXA255, with 85).
- * Those cases currently cause holes in the GPIO number space, the
- * actual number of the last GPIO is recorded by 'pxa_last_gpio'.
- */
-extern int pxa_last_gpio;
-
-typedef int (*set_wake_t)(struct irq_data *d, unsigned int on);
-
-extern void pxa_init_gpio(int mux_irq, int start, int end, set_wake_t fn);
-#endif /* __PLAT_GPIO_H */
diff --git a/arch/arm/plat-pxa/include/plat/mfp.h b/arch/arm/plat-pxa/include/plat/mfp.h
index 89e68e07b0a8..5c79c29f2833 100644
--- a/arch/arm/plat-pxa/include/plat/mfp.h
+++ b/arch/arm/plat-pxa/include/plat/mfp.h
@@ -456,7 +456,7 @@ struct mfp_addr_map {
 
 #define MFP_ADDR_END	{ MFP_PIN_INVALID, 0 }
 
-void __init mfp_init_base(unsigned long mfpr_base);
+void __init mfp_init_base(void __iomem *mfpr_base);
 void __init mfp_init_addr(struct mfp_addr_map *map);
 
 /*
diff --git a/arch/arm/plat-pxa/include/plat/pxa3xx_nand.h b/arch/arm/plat-pxa/include/plat/pxa3xx_nand.h
index 442301fe48b4..c42f39f20195 100644
--- a/arch/arm/plat-pxa/include/plat/pxa3xx_nand.h
+++ b/arch/arm/plat-pxa/include/plat/pxa3xx_nand.h
@@ -41,6 +41,19 @@ struct pxa3xx_nand_flash {
 	struct pxa3xx_nand_timing *timing;	/* NAND Flash timing */
 };
 
+/*
+ * Current pxa3xx_nand controller has two chip select which
+ * both be workable.
+ *
+ * Notice should be taken that:
+ * When you want to use this feature, you should not enable the
+ * keep configuration feature, for two chip select could be
+ * attached with different nand chip. The different page size
+ * and timing requirement make the keep configuration impossible.
+ */
+
+/* The max num of chip select current support */
+#define NUM_CHIP_SELECT		(2)
 struct pxa3xx_nand_platform_data {
 
 	/* the data flash bus is shared between the Static Memory
@@ -52,8 +65,11 @@ struct pxa3xx_nand_platform_data {
 	/* allow platform code to keep OBM/bootloader defined NFC config */
 	int	keep_config;
 
-	const struct mtd_partition		*parts;
-	unsigned int				nr_parts;
+	/* indicate how many chip selects will be used */
+	int	num_cs;
+
+	const struct mtd_partition		*parts[NUM_CHIP_SELECT];
+	unsigned int				nr_parts[NUM_CHIP_SELECT];
 
 	const struct pxa3xx_nand_flash * 	flash;
 	size_t					num_flash;