diff options
Diffstat (limited to 'arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi')
| -rw-r--r-- | arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi | 93 |
1 files changed, 88 insertions, 5 deletions
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi index 7e84a29dddfa..c4faff092380 100644 --- a/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi +++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi @@ -1,11 +1,12 @@ // SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) /* - * Device Tree Source for the RZ/G2L SMARC SOM common parts + * Device Tree Source for the RZ/{G2L,V2L} SMARC SOM common parts * * Copyright (C) 2021 Renesas Electronics Corp. */ #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irqc-rzg2l.h> #include <dt-bindings/pinctrl/rzg2l-pinctrl.h> /* SW1[2] should be at position 2/OFF to enable 64 GB eMMC */ @@ -34,7 +35,7 @@ reg = <0x0 0x48000000 0x0 0x78000000>; }; - reg_1p8v: regulator0 { + reg_1p8v: regulator-1p8v { compatible = "regulator-fixed"; regulator-name = "fixed-1.8V"; regulator-min-microvolt = <1800000>; @@ -43,7 +44,7 @@ regulator-always-on; }; - reg_3p3v: regulator1 { + reg_3p3v: regulator-3p3v { compatible = "regulator-fixed"; regulator-name = "fixed-3.3V"; regulator-min-microvolt = <3300000>; @@ -52,6 +53,15 @@ regulator-always-on; }; + reg_1p1v: regulator-vdd-core { + compatible = "regulator-fixed"; + regulator-name = "fixed-1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-boot-on; + regulator-always-on; + }; + vccq_sdhi0: regulator-vccq-sdhi0 { compatible = "regulator-gpio"; @@ -85,6 +95,8 @@ compatible = "ethernet-phy-id0022.1640", "ethernet-phy-ieee802.3-c22"; reg = <7>; + interrupt-parent = <&irqc>; + interrupts = <RZG2L_IRQ2 IRQ_TYPE_LEVEL_LOW>; rxc-skew-psec = <2400>; txc-skew-psec = <2400>; rxdv-skew-psec = <0>; @@ -111,6 +123,8 @@ compatible = "ethernet-phy-id0022.1640", "ethernet-phy-ieee802.3-c22"; reg = <7>; + interrupt-parent = <&irqc>; + interrupts = <RZG2L_IRQ3 IRQ_TYPE_LEVEL_LOW>; rxc-skew-psec = <2400>; txc-skew-psec = <2400>; rxdv-skew-psec = <0>; @@ -130,6 +144,18 @@ clock-frequency = <24000000>; }; +&gpu { + mali-supply = <®_1p1v>; +}; + +&ostm1 { + status = "okay"; +}; + +&ostm2 { + status = "okay"; +}; + &pinctrl { adc_pins: adc { pinmux = <RZG2L_PORT_PINMUX(9, 0, 2)>; /* ADC_TRG */ @@ -150,7 +176,8 @@ <RZG2L_PORT_PINMUX(25, 0, 1)>, /* ET0_RXD0 */ <RZG2L_PORT_PINMUX(25, 1, 1)>, /* ET0_RXD1 */ <RZG2L_PORT_PINMUX(26, 0, 1)>, /* ET0_RXD2 */ - <RZG2L_PORT_PINMUX(26, 1, 1)>; /* ET0_RXD3 */ + <RZG2L_PORT_PINMUX(26, 1, 1)>, /* ET0_RXD3 */ + <RZG2L_PORT_PINMUX(1, 0, 1)>; /* IRQ2 */ }; eth1_pins: eth1 { @@ -168,7 +195,8 @@ <RZG2L_PORT_PINMUX(34, 1, 1)>, /* ET1_RXD0 */ <RZG2L_PORT_PINMUX(35, 0, 1)>, /* ET1_RXD1 */ <RZG2L_PORT_PINMUX(35, 1, 1)>, /* ET1_RXD2 */ - <RZG2L_PORT_PINMUX(36, 0, 1)>; /* ET1_RXD3 */ + <RZG2L_PORT_PINMUX(36, 0, 1)>, /* ET1_RXD3 */ + <RZG2L_PORT_PINMUX(1, 1, 1)>; /* IRQ3 */ }; gpio-sd0-pwr-en-hog { @@ -178,6 +206,18 @@ line-name = "gpio_sd0_pwr_en"; }; + qspi0_pins: qspi0 { + qspi0-data { + pins = "QSPI0_IO0", "QSPI0_IO1", "QSPI0_IO2", "QSPI0_IO3"; + power-source = <1800>; + }; + + qspi0-ctrl { + pins = "QSPI0_SPCLK", "QSPI0_SSL", "QSPI_RESET#"; + power-source = <1800>; + }; + }; + /* * SD0 device selection is XOR between GPIO_SD0_DEV_SEL and SW1[2] * The below switch logic can be used to select the device between @@ -243,6 +283,34 @@ }; }; +&sbc { + pinctrl-0 = <&qspi0_pins>; + pinctrl-names = "default"; + status = "okay"; + + flash@0 { + compatible = "micron,mt25qu512a", "jedec,spi-nor"; + reg = <0>; + m25p,fast-read; + spi-max-frequency = <50000000>; + spi-rx-bus-width = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + boot@0 { + reg = <0x00000000 0x2000000>; + read-only; + }; + user@2000000 { + reg = <0x2000000 0x2000000>; + }; + }; + }; +}; + #if SDHI &sdhi0 { pinctrl-0 = <&sdhi0_pins>; @@ -273,3 +341,18 @@ status = "okay"; }; #endif + +&wdt0 { + status = "okay"; + timeout-sec = <60>; +}; + +&wdt1 { + status = "okay"; + timeout-sec = <60>; +}; + +&wdt2 { + status = "okay"; + timeout-sec = <60>; +}; |