diff options
Diffstat (limited to 'arch/arm64')
207 files changed, 13425 insertions, 2726 deletions
diff --git a/arch/arm64/Kconfig b/arch/arm64/Kconfig index 67695fadae96..3dcd7ec69bca 100644 --- a/arch/arm64/Kconfig +++ b/arch/arm64/Kconfig @@ -736,6 +736,17 @@ config KEXEC but it is independent of the system firmware. And like a reboot you can start any kernel with it, not just Linux. +config CRASH_DUMP + bool "Build kdump crash kernel" + help + Generate crash dump after being started by kexec. This should + be normally only set in special crash dump kernels which are + loaded in the main kernel with kexec-tools into a specially + reserved region and then later executed after a crash by + kdump/kexec. + + For more details see Documentation/kdump/kdump.txt + config XEN_DOM0 def_bool y depends on XEN diff --git a/arch/arm64/Kconfig.debug b/arch/arm64/Kconfig.debug index fca2f02cde68..cc6bd559af85 100644 --- a/arch/arm64/Kconfig.debug +++ b/arch/arm64/Kconfig.debug @@ -92,6 +92,10 @@ config DEBUG_EFI the kernel that are only useful when using a debug build of the UEFI firmware +config ARM64_RELOC_TEST + depends on m + tristate "Relocation testing module" + source "drivers/hwtracing/coresight/Kconfig" endmenu diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms index 129cc5ae4091..4afcffcb46cb 100644 --- a/arch/arm64/Kconfig.platforms +++ b/arch/arm64/Kconfig.platforms @@ -2,9 +2,10 @@ menu "Platform selection" config ARCH_SUNXI bool "Allwinner sunxi 64-bit SoC Family" + select ARCH_HAS_RESET_CONTROLLER select GENERIC_IRQ_CHIP select PINCTRL - select PINCTRL_SUN50I_A64 + select RESET_CONTROLLER help This enables support for Allwinner sunxi based SoCs like the A64. @@ -54,6 +55,8 @@ config ARCH_BRCMSTB config ARCH_EXYNOS bool "ARMv8 based Samsung Exynos SoC family" select COMMON_CLK_SAMSUNG + select EXYNOS_PM_DOMAINS if PM_GENERIC_DOMAINS + select EXYNOS_PMU select HAVE_S3C2410_WATCHDOG if WATCHDOG select HAVE_S3C_RTC if RTC_CLASS select PINCTRL diff --git a/arch/arm64/Makefile b/arch/arm64/Makefile index b9a4a934ca05..f839ecd919f9 100644 --- a/arch/arm64/Makefile +++ b/arch/arm64/Makefile @@ -37,10 +37,12 @@ $(warning LSE atomics not supported by binutils) endif endif +ifeq ($(CONFIG_ARM64), y) brokengasinst := $(call as-instr,1:\n.inst 0\n.rept . - 1b\n\nnop\n.endr\n,,-DCONFIG_BROKEN_GAS_INST=1) -ifneq ($(brokengasinst),) + ifneq ($(brokengasinst),) $(warning Detected assembler with broken .inst; disassembly will be unreliable) + endif endif KBUILD_CFLAGS += -mgeneral-regs-only $(lseinstr) $(brokengasinst) @@ -100,12 +102,12 @@ libs-y := arch/arm64/lib/ $(libs-y) core-$(CONFIG_EFI_STUB) += $(objtree)/drivers/firmware/efi/libstub/lib.a # Default target when executing plain make -KBUILD_IMAGE := Image.gz +boot := arch/arm64/boot +KBUILD_IMAGE := $(boot)/Image.gz KBUILD_DTBS := dtbs -all: $(KBUILD_IMAGE) $(KBUILD_DTBS) +all: Image.gz $(KBUILD_DTBS) -boot := arch/arm64/boot Image: vmlinux $(Q)$(MAKE) $(build)=$(boot) $(boot)/$@ diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index bc6f342be59f..244e8b7565f9 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -1,5 +1,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi index 0565779e66fa..c7f669f5884f 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi @@ -98,6 +98,14 @@ clock-output-names = "osc32k"; }; + iosc: internal-osc-clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <16000000>; + clock-accuracy = <300000000>; + clock-output-names = "iosc"; + }; + psci { compatible = "arm,psci-0.2"; method = "smc"; @@ -394,5 +402,26 @@ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; }; + + r_ccu: clock@1f01400 { + compatible = "allwinner,sun50i-a64-r-ccu"; + reg = <0x01f01400 0x100>; + clocks = <&osc24M>, <&osc32k>, <&iosc>; + clock-names = "hosc", "losc", "iosc"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + r_pio: pinctrl@01f02c00 { + compatible = "allwinner,sun50i-a64-r-pinctrl"; + reg = <0x01f02c00 0x400>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&r_ccu 3>, <&osc24M>, <&osc32k>; + clock-names = "apb", "hosc", "losc"; + gpio-controller; + #gpio-cells = <3>; + interrupt-controller; + #interrupt-cells = <3>; + }; }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts new file mode 100644 index 000000000000..dfecc17dcc92 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts @@ -0,0 +1,188 @@ +/* + * Copyright (C) 2016 ARM Ltd. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun50i-h5.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "Xunlong Orange Pi PC 2"; + compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5"; + + reg_vcc3v3: vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + pwr { + label = "orangepi:green:pwr"; + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + status { + label = "orangepi:red:status"; + gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>; + }; + }; + + r-gpio-keys { + compatible = "gpio-keys"; + + sw4 { + label = "sw4"; + linux,code = <BTN_0>; + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + }; + }; + + reg_usb0_vbus: usb0-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb0-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */ + status = "okay"; + }; +}; + +&codec { + allwinner,audio-routing = + "Line Out", "LINEOUT", + "MIC1", "Mic", + "Mic", "MBIAS"; + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +&ehci3 { + status = "okay"; +}; + +&ir { + pinctrl-names = "default"; + pinctrl-0 = <&ir_pins_a>; + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +&ohci3 { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "disabled"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "disabled"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + /* USB Type-A ports' VBUS is always on */ + usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ + usb0_vbus-supply = <®_usb0_vbus>; + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi new file mode 100644 index 000000000000..4d314a253fd9 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi @@ -0,0 +1,124 @@ +/* + * Copyright (C) 2016 ARM Ltd. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "sunxi-h3-h5.dtsi" + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "arm,cortex-a53", "arm,armv8"; + device_type = "cpu"; + reg = <0>; + enable-method = "psci"; + }; + + cpu@1 { + compatible = "arm,cortex-a53", "arm,armv8"; + device_type = "cpu"; + reg = <1>; + enable-method = "psci"; + }; + + cpu@2 { + compatible = "arm,cortex-a53", "arm,armv8"; + device_type = "cpu"; + reg = <2>; + enable-method = "psci"; + }; + + cpu@3 { + compatible = "arm,cortex-a53", "arm,armv8"; + device_type = "cpu"; + reg = <3>; + enable-method = "psci"; + }; + }; + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; +}; + +&ccu { + compatible = "allwinner,sun50i-h5-ccu"; +}; + +&mmc0 { + compatible = "allwinner,sun50i-h5-mmc", + "allwinner,sun50i-a64-mmc"; + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>; + clock-names = "ahb", "mmc"; +}; + +&mmc1 { + compatible = "allwinner,sun50i-h5-mmc", + "allwinner,sun50i-a64-mmc"; + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>; + clock-names = "ahb", "mmc"; +}; + +&mmc2 { + compatible = "allwinner,sun50i-h5-emmc", + "allwinner,sun50i-a64-emmc"; + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>; + clock-names = "ahb", "mmc"; +}; + +&pio { + compatible = "allwinner,sun50i-h5-pinctrl"; +}; diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi new file mode 120000 index 000000000000..036f01dc2b9b --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi @@ -0,0 +1 @@ +../../../../arm/boot/dts/sunxi-h3-h5.dtsi
\ No newline at end of file diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile index 3f94bce33b7f..b9ad2db7398b 100644 --- a/arch/arm64/boot/dts/amlogic/Makefile +++ b/arch/arm64/boot/dts/amlogic/Makefile @@ -7,9 +7,11 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-meta.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-telos.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-hub.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-play2.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-khadas-vim.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-hwacom-amazetv.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-nexbox-a95x.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxm-q200.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxm-q201.dtb diff --git a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi index 7a078bef04cd..a84e27622639 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi @@ -98,6 +98,27 @@ clocks = <&wifi32k>; clock-names = "ext_clock"; }; + + cvbs-connector { + compatible = "composite-video-connector"; + + port { + cvbs_connector_in: endpoint { + remote-endpoint = <&cvbs_vdac_out>; + }; + }; + }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; }; /* This UART is brought out to the DB9 connector */ @@ -188,3 +209,21 @@ ðmac { status = "okay"; }; + +&cvbs_vdac_port { + cvbs_vdac_out: endpoint { + remote-endpoint = <&cvbs_connector_in>; + }; +}; + +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>; + pinctrl-names = "default"; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi index 5d995f7724af..436b875060e7 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi @@ -71,6 +71,14 @@ reg = <0x0 0x10000000 0x0 0x200000>; no-map; }; + + linux,cma { + compatible = "shared-dma-pool"; + reusable; + size = <0x0 0xbc00000>; + alignment = <0x0 0x400000>; + linux,cma-default; + }; }; cpus { @@ -233,7 +241,7 @@ }; i2c_A: i2c@8500 { - compatible = "amlogic,meson-gxbb-i2c"; + compatible = "amlogic,meson-gx-i2c", "amlogic,meson-gxbb-i2c"; reg = <0x0 0x08500 0x0 0x20>; interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>; #address-cells = <1>; @@ -279,7 +287,7 @@ }; i2c_B: i2c@87c0 { - compatible = "amlogic,meson-gxbb-i2c"; + compatible = "amlogic,meson-gx-i2c", "amlogic,meson-gxbb-i2c"; reg = <0x0 0x087c0 0x0 0x20>; interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>; #address-cells = <1>; @@ -288,7 +296,7 @@ }; i2c_C: i2c@87e0 { - compatible = "amlogic,meson-gxbb-i2c"; + compatible = "amlogic,meson-gx-i2c", "amlogic,meson-gxbb-i2c"; reg = <0x0 0x087e0 0x0 0x20>; interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>; #address-cells = <1>; @@ -296,6 +304,14 @@ status = "disabled"; }; + spifc: spi@8c80 { + compatible = "amlogic,meson-gx-spifc", "amlogic,meson-gxbb-spifc"; + reg = <0x0 0x08c80 0x0 0x80>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + watchdog@98d0 { compatible = "amlogic,meson-gx-wdt", "amlogic,meson-gxbb-wdt"; reg = <0x0 0x098d0 0x0 0x10>; @@ -317,7 +333,7 @@ }; sram: sram@c8000000 { - compatible = "amlogic,meson-gxbb-sram", "mmio-sram"; + compatible = "amlogic,meson-gx-sram", "amlogic,meson-gxbb-sram", "mmio-sram"; reg = <0x0 0xc8000000 0x0 0x14000>; #address-cells = <1>; @@ -325,12 +341,12 @@ ranges = <0 0x0 0xc8000000 0x14000>; cpu_scp_lpri: scp-shmem@0 { - compatible = "amlogic,meson-gxbb-scp-shmem"; + compatible = "amlogic,meson-gx-scp-shmem", "amlogic,meson-gxbb-scp-shmem"; reg = <0x13000 0x400>; }; cpu_scp_hpri: scp-shmem@200 { - compatible = "amlogic,meson-gxbb-scp-shmem"; + compatible = "amlogic,meson-gx-scp-shmem", "amlogic,meson-gxbb-scp-shmem"; reg = <0x13400 0x400>; }; }; @@ -342,6 +358,13 @@ #size-cells = <2>; ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>; + clkc_AO: clock-controller@040 { + compatible = "amlogic,gx-aoclkc", "amlogic,gxbb-aoclkc"; + reg = <0x0 0x00040 0x0 0x4>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + uart_AO: serial@4c0 { compatible = "amlogic,meson-uart"; reg = <0x0 0x004c0 0x0 0x14>; @@ -358,6 +381,15 @@ status = "disabled"; }; + i2c_AO: i2c@500 { + compatible = "amlogic,meson-gx-i2c", "amlogic,meson-gxbb-i2c"; + reg = <0x0 0x500 0x0 0x20>; + interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + pwm_AO_ab: pwm@550 { compatible = "amlogic,meson-gx-pwm", "amlogic,meson-gxbb-pwm"; reg = <0x0 0x00550 0x0 0x10>; @@ -366,7 +398,7 @@ }; ir: ir@580 { - compatible = "amlogic,meson-gxbb-ir"; + compatible = "amlogic,meson-gx-ir", "amlogic,meson-gxbb-ir"; reg = <0x0 0x00580 0x0 0x40>; interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>; status = "disabled"; @@ -380,13 +412,12 @@ #size-cells = <2>; ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>; - rng { + hwrng: rng { compatible = "amlogic,meson-rng"; reg = <0x0 0x0 0x0 0x4>; }; }; - hiubus: hiubus@c883c000 { compatible = "simple-bus"; reg = <0x0 0xc883c000 0x0 0x2000>; @@ -410,7 +441,6 @@ 0x0 0xc8834540 0x0 0x4>; interrupts = <0 8 1>; interrupt-names = "macirq"; - phy-mode = "rgmii"; status = "disabled"; }; @@ -457,6 +487,38 @@ cvbs_vdac_port: port@0 { reg = <0>; }; + + /* HDMI-TX output port */ + hdmi_tx_port: port@1 { + reg = <1>; + + hdmi_tx_out: endpoint { + remote-endpoint = <&hdmi_tx_in>; + }; + }; + }; + + hdmi_tx: hdmi-tx@c883a000 { + compatible = "amlogic,meson-gx-dw-hdmi"; + reg = <0x0 0xc883a000 0x0 0x1c>; + interrupts = <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + /* VPU VENC Input */ + hdmi_tx_venc_port: port@0 { + reg = <0>; + + hdmi_tx_in: endpoint { + remote-endpoint = <&hdmi_tx_out>; + }; + }; + + /* TMDS Output */ + hdmi_tx_tmds_port: port@1 { + reg = <1>; + }; }; }; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts index 4cbd626a9e88..87198eafb04b 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts @@ -152,6 +152,17 @@ }; }; }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; }; &uart_AO { @@ -164,7 +175,24 @@ status = "okay"; pinctrl-0 = <ð_rmii_pins>; pinctrl-names = "default"; + + phy-handle = <ð_phy0>; phy-mode = "rmii"; + + snps,reset-gpio = <&gpio GPIOZ_14 0>; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-active-low; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + eth_phy0: ethernet-phy@0 { + /* IC Plus IP101GR (0x02430c54) */ + reg = <0>; + }; + }; }; &ir { @@ -245,3 +273,15 @@ remote-endpoint = <&cvbs_connector_in>; }; }; + +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>; + pinctrl-names = "default"; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts index c59403adb387..54a9c6a6b392 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts @@ -96,7 +96,7 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpio = <&gpio_ao GPIOAO_12 GPIO_ACTIVE_HIGH>; + gpio = <&gpio GPIOY_12 GPIO_ACTIVE_HIGH>; enable-active-high; }; @@ -152,6 +152,13 @@ pinctrl-0 = <ð_rgmii_pins>; pinctrl-names = "default"; phy-handle = <ð_phy0>; + phy-mode = "rgmii"; + + snps,reset-gpio = <&gpio GPIOZ_14 0>; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-active-low; + + amlogic,tx-delay-ns = <2>; mdio { compatible = "snps,dwmac-mdio"; @@ -165,6 +172,57 @@ }; }; +&pinctrl_aobus { + gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En", + "USB HUB nRESET", "USB OTG Power En", + "J7 Header Pin2", "IR In", "J7 Header Pin4", + "J7 Header Pin6", "J7 Header Pin5", "J7 Header Pin7", + "HDMI CEC", "SYS LED"; +}; + +&pinctrl_periphs { + gpio-line-names = /* Bank GPIOZ */ + "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk", + "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2", + "Eth RX D3", "Eth RGMII TX Clk", "Eth TX En", + "Eth TX D0", "Eth TX D1", "Eth TX D2", "Eth TX D3", + "Eth PHY nRESET", "Eth PHY Intc", + /* Bank GPIOH */ + "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL", "", + /* Bank BOOT */ + "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3", "eMMC D4", + "eMMC D5", "eMMC D6", "eMMC D7", "eMMC Clk", + "eMMC Reset", "eMMC CMD", + "", "", "", "", "", "", "", + /* Bank CARD */ + "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD", + "SDCard D3", "SDCard D2", "SDCard Det", + /* Bank GPIODV */ + "", "", "", "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", "", + "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK", + "PWM D", "PWM B", + /* Bank GPIOY */ + "Revision Bit0", "Revision Bit1", "", + "J2 Header Pin35", "", "", "", "J2 Header Pin36", + "J2 Header Pin31", "", "", "", "TF VDD En", + "J2 Header Pin32", "J2 Header Pin26", "", "", + /* Bank GPIOX */ + "J2 Header Pin29", "J2 Header Pin24", + "J2 Header Pin23", "J2 Header Pin22", + "J2 Header Pin21", "J2 Header Pin18", + "J2 Header Pin33", "J2 Header Pin19", + "J2 Header Pin16", "J2 Header Pin15", + "J2 Header Pin12", "J2 Header Pin13", + "J2 Header Pin8", "J2 Header Pin10", + "", "", "", "", "", + "J2 Header Pin11", "", "J2 Header Pin7", + /* Bank GPIOCLK */ + "", "", "", "", + /* GPIO_TEST_N */ + ""; +}; + &ir { status = "okay"; pinctrl-0 = <&remote_input_ao_pins>; @@ -177,6 +235,21 @@ pinctrl-names = "default"; }; +&gpio_ao { + /* + * WARNING: The USB Hub on the Odroid-C2 needs a reset signal + * to be turned high in order to be detected by the USB Controller + * This signal should be handled by a USB specific power sequence + * in order to reset the Hub when USB bus is powered down. + */ + usb-hub { + gpio-hog; + gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb-hub-reset"; + }; +}; + &usb0_phy { status = "okay"; phy-supply = <&usb_otg_pwr>; @@ -194,6 +267,11 @@ status = "okay"; }; +&saradc { + status = "okay"; + vref-supply = <&vcc1v8>; +}; + /* SD */ &sd_emmc_b { status = "okay"; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts index fc0e86cb4cde..2054a474e0a9 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts @@ -96,6 +96,31 @@ }; }; +ðmac { + status = "okay"; + pinctrl-0 = <ð_rgmii_pins>; + pinctrl-names = "default"; + phy-handle = <ð_phy0>; + phy-mode = "rgmii"; + + amlogic,tx-delay-ns = <2>; + + snps,reset-gpio = <&gpio GPIOZ_14 0>; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-active-low; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + eth_phy0: ethernet-phy@3 { + /* Micrel KSZ9031 (0x00221620) */ + reg = <3>; + }; + }; +}; + &i2c_B { status = "okay"; pinctrl-0 = <&i2c_b_pins>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts index 39bb037a3e47..ae3194663d64 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p201.dts @@ -50,3 +50,14 @@ compatible = "amlogic,p201", "amlogic,meson-gxbb"; model = "Amlogic Meson GXBB P201 Development Board"; }; + +ðmac { + status = "okay"; + pinctrl-0 = <ð_rmii_pins>; + pinctrl-names = "default"; + phy-mode = "rmii"; + + snps,reset-gpio = <&gpio GPIOZ_14 0>; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-active-low; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi index 4a96e0f6f926..3c6c0b7f4187 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi @@ -135,6 +135,17 @@ }; }; }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; }; /* This UART is brought out to the DB9 connector */ @@ -144,12 +155,6 @@ pinctrl-names = "default"; }; -ðmac { - status = "okay"; - pinctrl-0 = <ð_rgmii_pins>; - pinctrl-names = "default"; -}; - &ir { status = "okay"; pinctrl-0 = <&remote_input_ao_pins>; @@ -250,3 +255,15 @@ remote-endpoint = <&cvbs_connector_in>; }; }; + +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>; + pinctrl-names = "default"; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi index 86709929fd20..aefa66dff72d 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi @@ -115,7 +115,6 @@ status = "okay"; pinctrl-0 = <&uart_ao_a_pins>; pinctrl-names = "default"; - }; &ir { @@ -128,6 +127,26 @@ status = "okay"; pinctrl-0 = <ð_rgmii_pins>; pinctrl-names = "default"; + + phy-handle = <ð_phy0>; + phy-mode = "rgmii"; + + amlogic,tx-delay-ns = <2>; + + snps,reset-gpio = <&gpio GPIOZ_14 0>; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-active-low; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + eth_phy0: ethernet-phy@0 { + /* Realtek RTL8211F (0x001cc916) */ + reg = <0>; + }; + }; }; &usb0_phy { diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-hub.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-hub.dts index 56f855901262..f057fb48fee5 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-hub.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-hub.dts @@ -64,3 +64,29 @@ status = "disabled"; }; }; + +ðmac { + status = "okay"; + pinctrl-0 = <ð_rgmii_pins>; + pinctrl-names = "default"; + + phy-handle = <ð_phy0>; + phy-mode = "rgmii"; + + amlogic,tx-delay-ns = <2>; + + snps,reset-gpio = <&gpio GPIOZ_14 0>; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-active-low; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + eth_phy0: ethernet-phy@0 { + /* Realtek RTL8211F (0x001cc916) */ + reg = <0>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts index ea79fdd2c248..743acb5f5d06 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts @@ -87,6 +87,32 @@ }; }; +ðmac { + status = "okay"; + pinctrl-0 = <ð_rgmii_pins>; + pinctrl-names = "default"; + + phy-handle = <ð_phy0>; + phy-mode = "rgmii"; + + amlogic,tx-delay-ns = <2>; + + snps,reset-gpio = <&gpio GPIOZ_14 0>; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-active-low; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + eth_phy0: ethernet-phy@0 { + /* Realtek RTL8211F (0x001cc916) */ + reg = <0>; + }; + }; +}; + &i2c_A { status = "okay"; pinctrl-0 = <&i2c_a_pins>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi index 04b3324bc132..86105a69690a 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi @@ -97,17 +97,6 @@ }; }; -&cbus { - spifc: spi@8c80 { - compatible = "amlogic,meson-gxbb-spifc"; - reg = <0x0 0x08c80 0x0 0x80>; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&clkc CLKID_SPI>; - status = "disabled"; - }; -}; - ðmac { clocks = <&clkc CLKID_ETH>, <&clkc CLKID_FCLK_DIV2>, @@ -129,6 +118,7 @@ reg-names = "mux", "pull", "gpio"; gpio-controller; #gpio-cells = <2>; + gpio-ranges = <&pinctrl_aobus 0 0 14>; }; uart_ao_a_pins: uart_ao_a { @@ -203,30 +193,62 @@ function = "pwm_ao_b"; }; }; - }; - clkc_AO: clock-controller@040 { - compatible = "amlogic,gxbb-aoclkc"; - reg = <0x0 0x00040 0x0 0x4>; - #clock-cells = <1>; - #reset-cells = <1>; - }; + i2s_am_clk_pins: i2s_am_clk { + mux { + groups = "i2s_am_clk"; + function = "i2s_out_ao"; + }; + }; - pwm_ab_AO: pwm@550 { - compatible = "amlogic,meson-gxbb-pwm"; - reg = <0x0 0x0550 0x0 0x10>; - #pwm-cells = <3>; - status = "disabled"; - }; + i2s_out_ao_clk_pins: i2s_out_ao_clk { + mux { + groups = "i2s_out_ao_clk"; + function = "i2s_out_ao"; + }; + }; + + i2s_out_lr_clk_pins: i2s_out_lr_clk { + mux { + groups = "i2s_out_lr_clk"; + function = "i2s_out_ao"; + }; + }; + + i2s_out_ch01_ao_pins: i2s_out_ch01_ao { + mux { + groups = "i2s_out_ch01_ao"; + function = "i2s_out_ao"; + }; + }; + + i2s_out_ch23_ao_pins: i2s_out_ch23_ao { + mux { + groups = "i2s_out_ch23_ao"; + function = "i2s_out_ao"; + }; + }; + + i2s_out_ch45_ao_pins: i2s_out_ch45_ao { + mux { + groups = "i2s_out_ch45_ao"; + function = "i2s_out_ao"; + }; + }; - i2c_AO: i2c@500 { - compatible = "amlogic,meson-gxbb-i2c"; - reg = <0x0 0x500 0x0 0x20>; - interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>; - clocks = <&clkc CLKID_AO_I2C>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; + spdif_out_ao_6_pins: spdif_out_ao_6 { + mux { + groups = "spdif_out_ao_6"; + function = "spdif_out_ao"; + }; + }; + + spdif_out_ao_13_pins: spdif_out_ao_13 { + mux { + groups = "spdif_out_ao_13"; + function = "spdif_out_ao"; + }; + }; }; }; @@ -245,6 +267,7 @@ reg-names = "mux", "pull", "pull-enable", "gpio"; gpio-controller; #gpio-cells = <2>; + gpio-ranges = <&pinctrl_periphs 0 14 120>; }; emmc_pins: emmc { @@ -467,6 +490,34 @@ function = "hdmi_i2c"; }; }; + + i2sout_ch23_y_pins: i2sout_ch23_y { + mux { + groups = "i2sout_ch23_y"; + function = "i2s_out"; + }; + }; + + i2sout_ch45_y_pins: i2sout_ch45_y { + mux { + groups = "i2sout_ch45_y"; + function = "i2s_out"; + }; + }; + + i2sout_ch67_y_pins: i2sout_ch67_y { + mux { + groups = "i2sout_ch67_y"; + function = "i2s_out"; + }; + }; + + spdif_out_y_pins: spdif_out_y { + mux { + groups = "spdif_out_y"; + function = "spdif_out"; + }; + }; }; }; @@ -478,10 +529,51 @@ }; }; +&apb { + mali: gpu@c0000 { + compatible = "amlogic,meson-gxbb-mali", "arm,mali-450"; + reg = <0x0 0xc0000 0x0 0x40000>; + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "gp", "gpmmu", "pp", "pmu", + "pp0", "ppmmu0", "pp1", "ppmmu1", + "pp2", "ppmmu2"; + clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>; + clock-names = "bus", "core"; + + /* + * Mali clocking is provided by two identical clock paths + * MALI_0 and MALI_1 muxed to a single clock by a glitch + * free mux to safely change frequency while running. + */ + assigned-clocks = <&clkc CLKID_MALI_0_SEL>, + <&clkc CLKID_MALI_0>, + <&clkc CLKID_MALI>; /* Glitch free mux */ + assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>, + <0>, /* Do Nothing */ + <&clkc CLKID_MALI_0>; + assigned-clock-rates = <0>, /* Do Nothing */ + <666666666>, + <0>; /* Do Nothing */ + }; +}; + &i2c_A { clocks = <&clkc CLKID_I2C>; }; +&i2c_AO { + clocks = <&clkc CLKID_AO_I2C>; +}; + &i2c_B { clocks = <&clkc CLKID_I2C>; }; @@ -521,6 +613,27 @@ clock-names = "core", "clkin0", "clkin1"; }; +&spifc { + clocks = <&clkc CLKID_SPI>; +}; + &vpu { compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu"; }; + +&hwrng { + clocks = <&clkc CLKID_RNG0>; + clock-names = "core"; +}; + +&hdmi_tx { + compatible = "amlogic,meson-gxbb-dw-hdmi", "amlogic,meson-gx-dw-hdmi"; + resets = <&reset RESET_HDMITX_CAPB3>, + <&reset RESET_HDMI_SYSTEM_RESET>, + <&reset RESET_HDMI_TX>; + reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy"; + clocks = <&clkc CLKID_HDMI_PCLK>, + <&clkc CLKID_CLK81>, + <&clkc CLKID_GCLK_VENCI_INT0>; + clock-names = "isfr", "iahb", "venci"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-mali.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-mali.dtsi new file mode 100644 index 000000000000..f06cc234693b --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-mali.dtsi @@ -0,0 +1,43 @@ +/* + * Copyright (c) 2017 BayLibre SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + * + * SPDX-License-Identifier: (GPL-2.0+ OR MIT) + */ + +&apb { + mali: gpu@c0000 { + compatible = "amlogic,meson-gxbb-mali", "arm,mali-450"; + reg = <0x0 0xc0000 0x0 0x40000>; + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "gp", "gpmmu", "pp", "pmu", + "pp0", "ppmmu0", "pp1", "ppmmu1", + "pp2", "ppmmu2"; + clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>; + clock-names = "bus", "core"; + + /* + * Mali clocking is provided by two identical clock paths + * MALI_0 and MALI_1 muxed to a single clock by a glitch + * free mux to safely change frequency while running. + */ + assigned-clocks = <&clkc CLKID_MALI_0_SEL>, + <&clkc CLKID_MALI_0>, + <&clkc CLKID_MALI>; /* Glitch free mux */ + assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>, + <0>, /* Do Nothing */ + <&clkc CLKID_MALI_0>; + assigned-clock-rates = <0>, /* Do Nothing */ + <666666666>, + <0>; /* Do Nothing */ + }; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts index f66939cacd37..f9fbfdad8dde 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts @@ -43,12 +43,47 @@ /dts-v1/; +#include <dt-bindings/input/input.h> + #include "meson-gxl-s905d.dtsi" #include "meson-gx-p23x-q20x.dtsi" / { compatible = "amlogic,p230", "amlogic,s905d", "amlogic,meson-gxl"; model = "Amlogic Meson GXL (S905D) P230 Development Board"; + + adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 0>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1710000>; + + button-function { + label = "Update"; + linux,code = <KEY_VENDOR>; + press-threshold-microvolt = <10000>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + button@0 { + label = "power"; + linux,code = <KEY_POWER>; + gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>; + }; + }; + + vddio_ao18: regulator-vddio_ao18 { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_AO18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; }; /* P230 has exclusive choice between internal or external PHY */ @@ -59,6 +94,8 @@ /* Select external PHY by default */ phy-handle = <&external_phy>; + amlogic,tx-delay-ns = <2>; + /* External PHY reset is shared with internal PHY Led signals */ snps,reset-gpio = <&gpio GPIOZ_14 0>; snps,reset-delays-us = <0 10000 1000000>; @@ -75,3 +112,8 @@ max-speed = <1000>; }; }; + +&saradc { + status = "okay"; + vref-supply = <&vddio_ao18>; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi index 615308e55576..5a90e30c1006 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d.dtsi @@ -42,6 +42,7 @@ */ #include "meson-gxl.dtsi" +#include "meson-gxl-mali.dtsi" / { compatible = "amlogic,s905d", "amlogic,meson-gxl"; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts new file mode 100644 index 000000000000..2a5804ce7f4b --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts @@ -0,0 +1,164 @@ +/* + * Copyright (c) 2017 Carlo Caione + * Copyright (c) 2016 BayLibre, Inc. + * Author: Neil Armstrong <narmstrong@kernel.org> + * + * SPDX-License-Identifier: (GPL-2.0+ OR MIT) + */ + +/dts-v1/; + +#include "meson-gxl-s905x.dtsi" + +/ { + compatible = "hwacom,amazetv", "amlogic,s905x", "amlogic,meson-gxl"; + model = "Hwacom AmazeTV (S905X)"; + + aliases { + serial0 = &uart_AO; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + vddio_card: gpio-regulator { + compatible = "regulator-gpio"; + + regulator-name = "VDDIO_CARD"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>; + gpios-states = <1>; + + /* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */ + states = <1800000 0 + 3300000 1>; + }; + + vddio_boot: regulator-vddio_boot { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_BOOT"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; + + cvbs-connector { + compatible = "composite-video-connector"; + + port { + cvbs_connector_in: endpoint { + remote-endpoint = <&cvbs_vdac_out>; + }; + }; + }; +}; + +&cvbs_vdac_port { + cvbs_vdac_out: endpoint { + remote-endpoint = <&cvbs_connector_in>; + }; +}; + +ðmac { + status = "okay"; + phy-mode = "rmii"; + phy-handle = <&internal_phy>; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; +}; + +&pwm_ef { + status = "okay"; + pinctrl-0 = <&pwm_e_pins>; + pinctrl-names = "default"; + clocks = <&clkc CLKID_FCLK_DIV4>; + clock-names = "clkin0"; +}; + +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_pins>; + pinctrl-names = "default"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <100000000>; + disable-wp; + + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>; + cd-inverted; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_card>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>; + pinctrl-names = "default"; + + bus-width = <8>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <100000000>; + non-removable; + disable-wp; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts new file mode 100644 index 000000000000..3c8b0b51ef27 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts @@ -0,0 +1,114 @@ +/* + * Copyright (c) 2017 Martin Blumenstingl <martin.blumenstingl@googlemail.com>. + * + * SPDX-License-Identifier: (GPL-2.0+ OR MIT) + */ + +/dts-v1/; + +#include <dt-bindings/input/input.h> + +#include "meson-gxl-s905x-p212.dtsi" + +/ { + compatible = "khadas,vim", "amlogic,s905x", "amlogic,meson-gxl"; + model = "Khadas VIM"; + + adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 0>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1710000>; + + button-function { + label = "Function"; + linux,code = <KEY_FN>; + press-threshold-microvolt = <10000>; + }; + }; + + aliases { + serial2 = &uart_AO_B; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + button@0 { + label = "power"; + linux,code = <KEY_POWER>; + gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>; + }; + }; + + pwmleds { + compatible = "pwm-leds"; + + power { + label = "vim:red:power"; + pwms = <&pwm_AO_ab 1 7812500 0>; + max-brightness = <255>; + linux,default-trigger = "default-on"; + }; + }; +}; + +&i2c_A { + status = "okay"; + pinctrl-0 = <&i2c_a_pins>; + pinctrl-names = "default"; +}; + +&i2c_B { + status = "okay"; + pinctrl-0 = <&i2c_b_pins>; + pinctrl-names = "default"; + + rtc: rtc@51 { + /* has to be enabled manually when a battery is connected: */ + status = "disabled"; + compatible = "haoyu,hym8563"; + reg = <0x51>; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "xin32k"; + }; +}; + +&ir { + linux,rc-map-name = "rc-geekbox"; +}; + +&pwm_AO_ab { + status = "okay"; + pinctrl-0 = <&pwm_ao_a_3_pins>, <&pwm_ao_b_pins>; + pinctrl-names = "default"; + clocks = <&clkc CLKID_FCLK_DIV4>; + clock-names = "clkin0"; +}; + +&pwm_ef { + pinctrl-0 = <&pwm_e_pins>, <&pwm_f_clk_pins>; +}; + +&sd_emmc_a { + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* This is brought out on the Linux_RX (18) and Linux_TX (19) pins: */ +&uart_AO { + status = "okay"; +}; + +/* This is brought out on the UART_RX_AO_B (15) and UART_TX_AO_B (16) pins: */ +&uart_AO_B { + status = "okay"; + pinctrl-0 = <&uart_ao_b_pins>; + pinctrl-names = "default"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts index cea4a3eded9b..8873c058fad2 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts @@ -127,6 +127,17 @@ }; }; }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; }; &uart_AO { @@ -219,3 +230,15 @@ remote-endpoint = <&cvbs_connector_in>; }; }; + +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>; + pinctrl-names = "default"; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts index 9639f012b02b..db31e093f40e 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts @@ -43,23 +43,26 @@ /dts-v1/; -#include "meson-gxl-s905x.dtsi" +#include "meson-gxl-s905x-p212.dtsi" / { compatible = "amlogic,p212", "amlogic,s905x", "amlogic,meson-gxl"; model = "Amlogic Meson GXL (S905X) P212 Development Board"; - aliases { - serial0 = &uart_AO; - }; + cvbs-connector { + compatible = "composite-video-connector"; - chosen { - stdout-path = "serial0:115200n8"; + port { + cvbs_connector_in: endpoint { + remote-endpoint = <&cvbs_vdac_out>; + }; + }; }; +}; - memory@0 { - device_type = "memory"; - reg = <0x0 0x0 0x0 0x80000000>; +&cvbs_vdac_port { + cvbs_vdac_out: endpoint { + remote-endpoint = <&cvbs_connector_in>; }; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi new file mode 100644 index 000000000000..f3eea8e89d12 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi @@ -0,0 +1,173 @@ +/* + * Copyright (c) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>. + * Based on meson-gx-p23x-q20x.dtsi: + * - Copyright (c) 2016 Endless Computers, Inc. + * Author: Carlo Caione <carlo@endlessm.com> + * - Copyright (c) 2016 BayLibre, SAS. + * Author: Neil Armstrong <narmstrong@baylibre.com> + * + * SPDX-License-Identifier: (GPL-2.0+ OR MIT) + */ + +/* Common DTSI for devices which are based on the P212 reference board. */ + +#include "meson-gxl-s905x.dtsi" + +/ { + aliases { + serial0 = &uart_AO; + serial1 = &uart_A; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + vddio_boot: regulator-vddio_boot { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_BOOT"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vddio_ao18: regulator-vddio_ao18 { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_AO18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; +}; + +ðmac { + status = "okay"; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; +}; + +&saradc { + status = "okay"; + vref-supply = <&vddio_ao18>; +}; + +/* Wireless SDIO Module */ +&sd_emmc_a { + status = "okay"; + pinctrl-0 = <&sdio_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <100000000>; + + non-removable; + disable-wp; + + mmc-pwrseq = <&sdio_pwrseq>; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_pins>; + pinctrl-names = "default"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <100000000>; + disable-wp; + + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>; + cd-inverted; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>; + pinctrl-names = "default"; + + bus-width = <8>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <200000000>; + non-removable; + disable-wp; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +&pwm_ef { + status = "okay"; + pinctrl-0 = <&pwm_e_pins>; + pinctrl-names = "default"; + clocks = <&clkc CLKID_FCLK_DIV4>; + clock-names = "clkin0"; +}; + +/* This is connected to the Bluetooth module: */ +&uart_A { + status = "okay"; + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; + pinctrl-names = "default"; + uart-has-rtscts; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi index 08237ee1e362..0f78d836edaf 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x.dtsi @@ -42,6 +42,7 @@ */ #include "meson-gxl.dtsi" +#include "meson-gxl-mali.dtsi" / { compatible = "amlogic,s905x", "amlogic,meson-gxl"; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi index fe11b5fc61f7..d8e096dff10a 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi @@ -44,6 +44,7 @@ #include "meson-gx.dtsi" #include <dt-bindings/clock/gxbb-clkc.h> #include <dt-bindings/gpio/meson-gxl-gpio.h> +#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h> / { compatible = "amlogic,meson-gxl"; @@ -79,6 +80,7 @@ reg-names = "mux", "pull", "gpio"; gpio-controller; #gpio-cells = <2>; + gpio-ranges = <&pinctrl_aobus 0 0 14>; }; uart_ao_a_pins: uart_ao_a { @@ -103,6 +105,13 @@ }; }; + uart_ao_b_0_1_pins: uart_ao_b_0_1 { + mux { + groups = "uart_tx_ao_b_0", "uart_rx_ao_b_1"; + function = "uart_ao_b"; + }; + }; + uart_ao_b_cts_rts_pins: uart_ao_b_cts_rts { mux { groups = "uart_cts_ao_b", @@ -118,12 +127,69 @@ }; }; + i2c_ao_pins: i2c_ao { + mux { + groups = "i2c_sck_ao", + "i2c_sda_ao"; + function = "i2c_ao"; + }; + }; + + pwm_ao_a_3_pins: pwm_ao_a_3 { + mux { + groups = "pwm_ao_a_3"; + function = "pwm_ao_a"; + }; + }; + + pwm_ao_a_8_pins: pwm_ao_a_8 { + mux { + groups = "pwm_ao_a_8"; + function = "pwm_ao_a"; + }; + }; + pwm_ao_b_pins: pwm_ao_b { mux { groups = "pwm_ao_b"; function = "pwm_ao_b"; }; }; + + pwm_ao_b_6_pins: pwm_ao_b_6 { + mux { + groups = "pwm_ao_b_6"; + function = "pwm_ao_b"; + }; + }; + + i2s_out_ch23_ao_pins: i2s_out_ch23_ao { + mux { + groups = "i2s_out_ch23_ao"; + function = "i2s_out_ao"; + }; + }; + + i2s_out_ch45_ao_pins: i2s_out_ch45_ao { + mux { + groups = "i2s_out_ch45_ao"; + function = "i2s_out_ao"; + }; + }; + + spdif_out_ao_6_pins: spdif_out_ao_6 { + mux { + groups = "spdif_out_ao_6"; + function = "spdif_out_ao"; + }; + }; + + spdif_out_ao_9_pins: spdif_out_ao_9 { + mux { + groups = "spdif_out_ao_9"; + function = "spdif_out_ao"; + }; + }; }; }; @@ -142,6 +208,7 @@ reg-names = "mux", "pull", "pull-enable", "gpio"; gpio-controller; #gpio-cells = <2>; + gpio-ranges = <&pinctrl_periphs 0 14 101>; }; emmc_pins: emmc { @@ -154,6 +221,16 @@ }; }; + nor_pins: nor { + mux { + groups = "nor_d", + "nor_q", + "nor_c", + "nor_cs"; + function = "nor"; + }; + }; + sdcard_pins: sdcard { mux { groups = "sdcard_d0", @@ -277,6 +354,34 @@ }; }; + pwm_a_pins: pwm_a { + mux { + groups = "pwm_a"; + function = "pwm_a"; + }; + }; + + pwm_b_pins: pwm_b { + mux { + groups = "pwm_b"; + function = "pwm_b"; + }; + }; + + pwm_c_pins: pwm_c { + mux { + groups = "pwm_c"; + function = "pwm_c"; + }; + }; + + pwm_d_pins: pwm_d { + mux { + groups = "pwm_d"; + function = "pwm_d"; + }; + }; + pwm_e_pins: pwm_e { mux { groups = "pwm_e"; @@ -284,6 +389,20 @@ }; }; + pwm_f_clk_pins: pwm_f_clk { + mux { + groups = "pwm_f_clk"; + function = "pwm_f"; + }; + }; + + pwm_f_x_pins: pwm_f_x { + mux { + groups = "pwm_f_x"; + function = "pwm_f"; + }; + }; + hdmi_hpd_pins: hdmi_hpd { mux { groups = "hdmi_hpd"; @@ -297,6 +416,61 @@ function = "hdmi_i2c"; }; }; + + i2s_am_clk_pins: i2s_am_clk { + mux { + groups = "i2s_am_clk"; + function = "i2s_out"; + }; + }; + + i2s_out_ao_clk_pins: i2s_out_ao_clk { + mux { + groups = "i2s_out_ao_clk"; + function = "i2s_out"; + }; + }; + + i2s_out_lr_clk_pins: i2s_out_lr_clk { + mux { + groups = "i2s_out_lr_clk"; + function = "i2s_out"; + }; + }; + + i2s_out_ch01_pins: i2s_out_ch01 { + mux { + groups = "i2s_out_ch01"; + function = "i2s_out"; + }; + }; + i2sout_ch23_z_pins: i2sout_ch23_z { + mux { + groups = "i2sout_ch23_z"; + function = "i2s_out"; + }; + }; + + i2sout_ch45_z_pins: i2sout_ch45_z { + mux { + groups = "i2sout_ch45_z"; + function = "i2s_out"; + }; + }; + + i2sout_ch67_z_pins: i2sout_ch67_z { + mux { + groups = "i2sout_ch67_z"; + function = "i2s_out"; + }; + }; + + spdif_out_h_pins: spdif_out_ao_h { + mux { + groups = "spdif_out_h"; + function = "spdif_out"; + }; + }; }; eth-phy-mux { @@ -339,6 +513,10 @@ clocks = <&clkc CLKID_I2C>; }; +&i2c_AO { + clocks = <&clkc CLKID_AO_I2C>; +}; + &i2c_B { clocks = <&clkc CLKID_I2C>; }; @@ -378,6 +556,22 @@ clock-names = "core", "clkin0", "clkin1"; }; +&spifc { + clocks = <&clkc CLKID_SPI>; +}; + &vpu { compatible = "amlogic,meson-gxl-vpu", "amlogic,meson-gx-vpu"; }; + +&hdmi_tx { + compatible = "amlogic,meson-gxl-dw-hdmi", "amlogic,meson-gx-dw-hdmi"; + resets = <&reset RESET_HDMITX_CAPB3>, + <&reset RESET_HDMI_SYSTEM_RESET>, + <&reset RESET_HDMI_TX>; + reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy"; + clocks = <&clkc CLKID_HDMI_PCLK>, + <&clkc CLKID_CLK81>, + <&clkc CLKID_GCLK_VENCI_INT0>; + clock-names = "isfr", "iahb", "venci"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts index 5a337d339df1..11b0bf46a95c 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts @@ -100,6 +100,17 @@ }; }; }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; }; /* This UART is brought out to the DB9 connector */ @@ -162,6 +173,8 @@ /* Select external PHY by default */ phy-handle = <&external_phy>; + amlogic,tx-delay-ns = <2>; + snps,reset-gpio = <&gpio GPIOZ_14 0>; snps,reset-delays-us = <0 10000 1000000>; snps,reset-active-low; @@ -183,3 +196,15 @@ remote-endpoint = <&cvbs_connector_in>; }; }; + +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>; + pinctrl-names = "default"; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts index 5dbc66088355..b65776b01911 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts @@ -43,12 +43,47 @@ /dts-v1/; +#include <dt-bindings/input/input.h> + #include "meson-gxm.dtsi" #include "meson-gx-p23x-q20x.dtsi" / { compatible = "amlogic,q200", "amlogic,s912", "amlogic,meson-gxm"; model = "Amlogic Meson GXM (S912) Q200 Development Board"; + + adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 0>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1710000>; + + button-function { + label = "Update"; + linux,code = <KEY_VENDOR>; + press-threshold-microvolt = <10000>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + button@0 { + label = "power"; + linux,code = <KEY_POWER>; + gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>; + }; + }; + + vddio_ao18: regulator-vddio_ao18 { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_AO18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; }; /* Q200 has exclusive choice between internal or external PHY */ @@ -59,6 +94,8 @@ /* Select external PHY by default */ phy-handle = <&external_phy>; + amlogic,tx-delay-ns = <2>; + /* External PHY reset is shared with internal PHY Led signals */ snps,reset-gpio = <&gpio GPIOZ_14 0>; snps,reset-delays-us = <0 10000 1000000>; @@ -75,3 +112,8 @@ max-speed = <1000>; }; }; + +&saradc { + status = "okay"; + vref-supply = <&vddio_ao18>; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi index ddea7305c644..fe451cce93e7 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi @@ -130,3 +130,6 @@ compatible = "amlogic,meson-gxm-vpu", "amlogic,meson-gx-vpu"; }; +&hdmi_tx { + compatible = "amlogic,meson-gxm-dw-hdmi", "amlogic,meson-gx-dw-hdmi"; +}; diff --git a/arch/arm64/boot/dts/arm/juno-base.dtsi b/arch/arm64/boot/dts/arm/juno-base.dtsi index df539e865b90..bfe7d683a42e 100644 --- a/arch/arm64/boot/dts/arm/juno-base.dtsi +++ b/arch/arm64/boot/dts/arm/juno-base.dtsi @@ -428,7 +428,7 @@ }; }; - pcie_ctlr: pcie-controller@40000000 { + pcie_ctlr: pcie@40000000 { compatible = "arm,juno-r1-pcie", "plda,xpressrich3-axi", "pci-host-ecam-generic"; device_type = "pci"; reg = <0 0x40000000 0 0x10000000>; /* ECAM config space */ @@ -699,7 +699,7 @@ <0x00000008 0x80000000 0x1 0x80000000>; }; - smb@08000000 { + smb@8000000 { compatible = "simple-bus"; #address-cells = <2>; #size-cells = <1>; diff --git a/arch/arm64/boot/dts/arm/juno-motherboard.dtsi b/arch/arm64/boot/dts/arm/juno-motherboard.dtsi index 098601657f82..2ac43221ddb6 100644 --- a/arch/arm64/boot/dts/arm/juno-motherboard.dtsi +++ b/arch/arm64/boot/dts/arm/juno-motherboard.dtsi @@ -137,7 +137,7 @@ #size-cells = <1>; ranges = <0 3 0 0x200000>; - v2m_sysctl: sysctl@020000 { + v2m_sysctl: sysctl@20000 { compatible = "arm,sp810", "arm,primecell"; reg = <0x020000 0x1000>; clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&mb_clk24mhz>; @@ -148,7 +148,7 @@ assigned-clock-parents = <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>; }; - apbregs@010000 { + apbregs@10000 { compatible = "syscon", "simple-mfd"; reg = <0x010000 0x1000>; @@ -216,7 +216,7 @@ }; }; - mmci@050000 { + mmci@50000 { compatible = "arm,pl180", "arm,primecell"; reg = <0x050000 0x1000>; interrupts = <5>; @@ -228,7 +228,7 @@ clock-names = "mclk", "apb_pclk"; }; - kmi@060000 { + kmi@60000 { compatible = "arm,pl050", "arm,primecell"; reg = <0x060000 0x1000>; interrupts = <8>; @@ -236,7 +236,7 @@ clock-names = "KMIREFCLK", "apb_pclk"; }; - kmi@070000 { + kmi@70000 { compatible = "arm,pl050", "arm,primecell"; reg = <0x070000 0x1000>; interrupts = <8>; @@ -244,7 +244,7 @@ clock-names = "KMIREFCLK", "apb_pclk"; }; - wdt@0f0000 { + wdt@f0000 { compatible = "arm,sp805", "arm,primecell"; reg = <0x0f0000 0x10000>; interrupts = <7>; diff --git a/arch/arm64/boot/dts/arm/juno-r1.dts b/arch/arm64/boot/dts/arm/juno-r1.dts index 0033c59a64b5..0e8943ab94d7 100644 --- a/arch/arm64/boot/dts/arm/juno-r1.dts +++ b/arch/arm64/boot/dts/arm/juno-r1.dts @@ -89,6 +89,12 @@ reg = <0x0 0x0>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0xc000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <256>; next-level-cache = <&A57_L2>; clocks = <&scpi_dvfs 0>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -100,6 +106,12 @@ reg = <0x0 0x1>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0xc000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <256>; next-level-cache = <&A57_L2>; clocks = <&scpi_dvfs 0>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -111,6 +123,12 @@ reg = <0x0 0x100>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; clocks = <&scpi_dvfs 1>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -122,6 +140,12 @@ reg = <0x0 0x101>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; clocks = <&scpi_dvfs 1>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -133,6 +157,12 @@ reg = <0x0 0x102>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; clocks = <&scpi_dvfs 1>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -144,6 +174,12 @@ reg = <0x0 0x103>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; clocks = <&scpi_dvfs 1>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -152,10 +188,16 @@ A57_L2: l2-cache0 { compatible = "cache"; + cache-size = <0x200000>; + cache-line-size = <64>; + cache-sets = <2048>; }; A53_L2: l2-cache1 { compatible = "cache"; + cache-size = <0x100000>; + cache-line-size = <64>; + cache-sets = <1024>; }; }; diff --git a/arch/arm64/boot/dts/arm/juno-r2.dts b/arch/arm64/boot/dts/arm/juno-r2.dts index 218d0e4736a8..405e2fba025b 100644 --- a/arch/arm64/boot/dts/arm/juno-r2.dts +++ b/arch/arm64/boot/dts/arm/juno-r2.dts @@ -89,6 +89,12 @@ reg = <0x0 0x0>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0xc000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <256>; next-level-cache = <&A72_L2>; clocks = <&scpi_dvfs 0>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -100,6 +106,12 @@ reg = <0x0 0x1>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0xc000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <256>; next-level-cache = <&A72_L2>; clocks = <&scpi_dvfs 0>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -111,6 +123,12 @@ reg = <0x0 0x100>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; clocks = <&scpi_dvfs 1>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -122,6 +140,12 @@ reg = <0x0 0x101>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; clocks = <&scpi_dvfs 1>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -133,6 +157,12 @@ reg = <0x0 0x102>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; clocks = <&scpi_dvfs 1>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -144,6 +174,12 @@ reg = <0x0 0x103>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; clocks = <&scpi_dvfs 1>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -152,10 +188,16 @@ A72_L2: l2-cache0 { compatible = "cache"; + cache-size = <0x200000>; + cache-line-size = <64>; + cache-sets = <2048>; }; A53_L2: l2-cache1 { compatible = "cache"; + cache-size = <0x100000>; + cache-line-size = <64>; + cache-sets = <1024>; }; }; diff --git a/arch/arm64/boot/dts/arm/juno.dts b/arch/arm64/boot/dts/arm/juno.dts index bb2820ef3d5b..0220494c9b80 100644 --- a/arch/arm64/boot/dts/arm/juno.dts +++ b/arch/arm64/boot/dts/arm/juno.dts @@ -88,6 +88,12 @@ reg = <0x0 0x0>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0xc000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <256>; next-level-cache = <&A57_L2>; clocks = <&scpi_dvfs 0>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -99,6 +105,12 @@ reg = <0x0 0x1>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0xc000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <256>; next-level-cache = <&A57_L2>; clocks = <&scpi_dvfs 0>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -110,6 +122,12 @@ reg = <0x0 0x100>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; clocks = <&scpi_dvfs 1>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -121,6 +139,12 @@ reg = <0x0 0x101>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; clocks = <&scpi_dvfs 1>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -132,6 +156,12 @@ reg = <0x0 0x102>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; clocks = <&scpi_dvfs 1>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -143,6 +173,12 @@ reg = <0x0 0x103>; device_type = "cpu"; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; clocks = <&scpi_dvfs 1>; cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>; @@ -151,10 +187,16 @@ A57_L2: l2-cache0 { compatible = "cache"; + cache-size = <0x200000>; + cache-line-size = <64>; + cache-sets = <2048>; }; A53_L2: l2-cache1 { compatible = "cache"; + cache-size = <0x100000>; + cache-line-size = <64>; + cache-sets = <1024>; }; }; diff --git a/arch/arm64/boot/dts/broadcom/Makefile b/arch/arm64/boot/dts/broadcom/Makefile index f1caece9d3a7..bfa8f8e4c5af 100644 --- a/arch/arm64/boot/dts/broadcom/Makefile +++ b/arch/arm64/boot/dts/broadcom/Makefile @@ -1,6 +1,5 @@ dtb-$(CONFIG_ARCH_BCM2835) += bcm2837-rpi-3-b.dtb dtb-$(CONFIG_ARCH_BCM_IPROC) += ns2-svk.dtb ns2-xmc.dtb -dtb-$(CONFIG_ARCH_VULCAN) += vulcan-eval.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/broadcom/ns2-svk.dts b/arch/arm64/boot/dts/broadcom/ns2-svk.dts index 5ae08161649e..ec19fbf928a1 100644 --- a/arch/arm64/boot/dts/broadcom/ns2-svk.dts +++ b/arch/arm64/boot/dts/broadcom/ns2-svk.dts @@ -57,55 +57,55 @@ }; &enet { - status = "ok"; + status = "okay"; }; &pci_phy0 { - status = "ok"; + status = "okay"; }; &pci_phy1 { - status = "ok"; + status = "okay"; }; &pcie0 { - status = "ok"; + status = "okay"; }; &pcie4 { - status = "ok"; + status = "okay"; }; &pcie8 { - status = "ok"; + status = "okay"; }; &i2c0 { - status = "ok"; + status = "okay"; }; &i2c1 { - status = "ok"; + status = "okay"; }; &uart0 { - status = "ok"; + status = "okay"; }; &uart1 { - status = "ok"; + status = "okay"; }; &uart2 { - status = "ok"; + status = "okay"; }; &uart3 { - status = "ok"; + status = "okay"; }; &ssp0 { - status = "ok"; + status = "okay"; slic@0 { compatible = "silabs,si3226x"; @@ -126,7 +126,7 @@ }; &ssp1 { - status = "ok"; + status = "okay"; at25@0 { compatible = "atmel,at25"; @@ -150,23 +150,23 @@ }; &sata_phy0 { - status = "ok"; + status = "okay"; }; &sata_phy1 { - status = "ok"; + status = "okay"; }; &sata { - status = "ok"; + status = "okay"; }; &sdio0 { - status = "ok"; + status = "okay"; }; &sdio1 { - status = "ok"; + status = "okay"; }; &nand { diff --git a/arch/arm64/boot/dts/broadcom/ns2-xmc.dts b/arch/arm64/boot/dts/broadcom/ns2-xmc.dts index 99a2723cccd2..ab4ae1a32fab 100644 --- a/arch/arm64/boot/dts/broadcom/ns2-xmc.dts +++ b/arch/arm64/boot/dts/broadcom/ns2-xmc.dts @@ -54,15 +54,15 @@ }; &enet { - status = "ok"; + status = "okay"; }; &i2c0 { - status = "ok"; + status = "okay"; }; &i2c1 { - status = "ok"; + status = "okay"; }; &mdio_mux_iproc { @@ -122,27 +122,27 @@ }; &pci_phy0 { - status = "ok"; + status = "okay"; }; &pcie0 { - status = "ok"; + status = "okay"; }; &pcie8 { - status = "ok"; + status = "okay"; }; &sata_phy0 { - status = "ok"; + status = "okay"; }; &sata_phy1 { - status = "ok"; + status = "okay"; }; &sata { - status = "ok"; + status = "okay"; }; &qspi { @@ -187,5 +187,5 @@ }; &uart3 { - status = "ok"; + status = "okay"; }; diff --git a/arch/arm64/boot/dts/broadcom/ns2.dtsi b/arch/arm64/boot/dts/broadcom/ns2.dtsi index bcb03fc32665..35a309ae3ed8 100644 --- a/arch/arm64/boot/dts/broadcom/ns2.dtsi +++ b/arch/arm64/boot/dts/broadcom/ns2.dtsi @@ -222,6 +222,12 @@ brcm,use-bcm-hdr; }; + crypto0: crypto@612d0000 { + compatible = "brcm,spum-crypto"; + reg = <0x612d0000 0x900>; + mboxes = <&pdc0 0>; + }; + pdc1: iproc-pdc1@612e0000 { compatible = "brcm,iproc-pdc-mbox"; reg = <0x612e0000 0x445>; /* PDC FS1 regs */ @@ -232,6 +238,12 @@ brcm,use-bcm-hdr; }; + crypto1: crypto@612f0000 { + compatible = "brcm,spum-crypto"; + reg = <0x612f0000 0x900>; + mboxes = <&pdc1 0>; + }; + pdc2: iproc-pdc2@61300000 { compatible = "brcm,iproc-pdc-mbox"; reg = <0x61300000 0x445>; /* PDC FS2 regs */ @@ -242,6 +254,12 @@ brcm,use-bcm-hdr; }; + crypto2: crypto@61310000 { + compatible = "brcm,spum-crypto"; + reg = <0x61310000 0x900>; + mboxes = <&pdc2 0>; + }; + pdc3: iproc-pdc3@61320000 { compatible = "brcm,iproc-pdc-mbox"; reg = <0x61320000 0x445>; /* PDC FS3 regs */ @@ -252,6 +270,12 @@ brcm,use-bcm-hdr; }; + crypto3: crypto@61330000 { + compatible = "brcm,spum-crypto"; + reg = <0x61330000 0x900>; + mboxes = <&pdc3 0>; + }; + dma0: dma@61360000 { compatible = "arm,pl330", "arm,primecell"; reg = <0x61360000 0x1000>; diff --git a/arch/arm64/boot/dts/cavium/Makefile b/arch/arm64/boot/dts/cavium/Makefile index e34f89ddabb2..581b2c1c400a 100644 --- a/arch/arm64/boot/dts/cavium/Makefile +++ b/arch/arm64/boot/dts/cavium/Makefile @@ -1,4 +1,5 @@ dtb-$(CONFIG_ARCH_THUNDER) += thunder-88xx.dtb +dtb-$(CONFIG_ARCH_THUNDER2) += thunder2-99xx.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/broadcom/vulcan-eval.dts b/arch/arm64/boot/dts/cavium/thunder2-99xx.dts index 9ee8d3da0e3f..6c6fb8692fde 100644 --- a/arch/arm64/boot/dts/broadcom/vulcan-eval.dts +++ b/arch/arm64/boot/dts/cavium/thunder2-99xx.dts @@ -1,6 +1,7 @@ /* - * dts file for Broadcom (BRCM) Vulcan Evaluation Platform + * dts file for Cavium ThunderX2 CN99XX Evaluation Platform * + * Copyright (c) 2017 Cavium Inc. * Copyright (c) 2013-2016 Broadcom * * This program is free software; you can redistribute it and/or @@ -11,11 +12,11 @@ /dts-v1/; -#include "vulcan.dtsi" +#include "thunder2-99xx.dtsi" / { - model = "Broadcom Vulcan Eval Platform"; - compatible = "brcm,vulcan-eval", "brcm,vulcan-soc"; + model = "Cavium ThunderX2 CN99XX"; + compatible = "cavium,thunderx2-cn9900", "brcm,vulcan-soc"; memory { device_type = "memory"; diff --git a/arch/arm64/boot/dts/broadcom/vulcan.dtsi b/arch/arm64/boot/dts/cavium/thunder2-99xx.dtsi index 34e11a9db2a0..4220fbdcb24a 100644 --- a/arch/arm64/boot/dts/broadcom/vulcan.dtsi +++ b/arch/arm64/boot/dts/cavium/thunder2-99xx.dtsi @@ -1,6 +1,7 @@ /* - * dtsi file for Broadcom (BRCM) Vulcan processor + * dtsi file for Cavium ThunderX2 CN99XX processor * + * Copyright (c) 2017 Cavium Inc. * Copyright (c) 2013-2016 Broadcom * Author: Zi Shen Lim <zlim@broadcom.com> * @@ -13,8 +14,8 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> / { - model = "Broadcom Vulcan"; - compatible = "brcm,vulcan-soc"; + model = "Cavium ThunderX2 CN99XX"; + compatible = "cavium,thunderx2-cn9900", "brcm,vulcan-soc"; interrupt-parent = <&gic>; #address-cells = <2>; #size-cells = <2>; @@ -26,28 +27,28 @@ cpu@0 { device_type = "cpu"; - compatible = "brcm,vulcan", "arm,armv8"; + compatible = "cavium,thunder2", "brcm,vulcan", "arm,armv8"; reg = <0x0 0x0>; enable-method = "psci"; }; cpu@1 { device_type = "cpu"; - compatible = "brcm,vulcan", "arm,armv8"; + compatible = "cavium,thunder2", "brcm,vulcan", "arm,armv8"; reg = <0x0 0x1>; enable-method = "psci"; }; cpu@2 { device_type = "cpu"; - compatible = "brcm,vulcan", "arm,armv8"; + compatible = "cavium,thunder2", "brcm,vulcan", "arm,armv8"; reg = <0x0 0x2>; enable-method = "psci"; }; cpu@3 { device_type = "cpu"; - compatible = "brcm,vulcan", "arm,armv8"; + compatible = "cavium,thunder2", "brcm,vulcan", "arm,armv8"; reg = <0x0 0x3>; enable-method = "psci"; }; diff --git a/arch/arm64/boot/dts/exynos/exynos5433-bus.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-bus.dtsi index c42dc39c3223..ec11343dc528 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433-bus.dtsi +++ b/arch/arm64/boot/dts/exynos/exynos5433-bus.dtsi @@ -94,27 +94,27 @@ compatible = "operating-points-v2"; opp-shared; - opp@400000000 { + opp-400000000 { opp-hz = /bits/ 64 <400000000>; opp-microvolt = <1075000>; }; - opp@267000000 { + opp-267000000 { opp-hz = /bits/ 64 <267000000>; opp-microvolt = <1000000>; }; - opp@200000000 { + opp-200000000 { opp-hz = /bits/ 64 <200000000>; opp-microvolt = <975000>; }; - opp@160000000 { + opp-160000000 { opp-hz = /bits/ 64 <160000000>; opp-microvolt = <962500>; }; - opp@134000000 { + opp-134000000 { opp-hz = /bits/ 64 <134000000>; opp-microvolt = <950000>; }; - opp@100000000 { + opp-100000000 { opp-hz = /bits/ 64 <100000000>; opp-microvolt = <937500>; }; @@ -123,19 +123,19 @@ bus_g2d_266_opp_table: opp_table3 { compatible = "operating-points-v2"; - opp@267000000 { + opp-267000000 { opp-hz = /bits/ 64 <267000000>; }; - opp@200000000 { + opp-200000000 { opp-hz = /bits/ 64 <200000000>; }; - opp@160000000 { + opp-160000000 { opp-hz = /bits/ 64 <160000000>; }; - opp@134000000 { + opp-134000000 { opp-hz = /bits/ 64 <134000000>; }; - opp@100000000 { + opp-100000000 { opp-hz = /bits/ 64 <100000000>; }; }; @@ -143,13 +143,13 @@ bus_gscl_opp_table: opp_table4 { compatible = "operating-points-v2"; - opp@333000000 { + opp-333000000 { opp-hz = /bits/ 64 <333000000>; }; - opp@222000000 { + opp-222000000 { opp-hz = /bits/ 64 <222000000>; }; - opp@166500000 { + opp-166500000 { opp-hz = /bits/ 64 <166500000>; }; }; @@ -158,22 +158,22 @@ compatible = "operating-points-v2"; opp-shared; - opp@400000000 { + opp-400000000 { opp-hz = /bits/ 64 <400000000>; }; - opp@267000000 { + opp-267000000 { opp-hz = /bits/ 64 <267000000>; }; - opp@200000000 { + opp-200000000 { opp-hz = /bits/ 64 <200000000>; }; - opp@160000000 { + opp-160000000 { opp-hz = /bits/ 64 <160000000>; }; - opp@134000000 { + opp-134000000 { opp-hz = /bits/ 64 <134000000>; }; - opp@100000000 { + opp-100000000 { opp-hz = /bits/ 64 <100000000>; }; }; @@ -181,16 +181,16 @@ bus_noc2_opp_table: opp_table6 { compatible = "operating-points-v2"; - opp@400000000 { + opp-400000000 { opp-hz = /bits/ 64 <400000000>; }; - opp@200000000 { + opp-200000000 { opp-hz = /bits/ 64 <200000000>; }; - opp@134000000 { + opp-134000000 { opp-hz = /bits/ 64 <134000000>; }; - opp@100000000 { + opp-100000000 { opp-hz = /bits/ 64 <100000000>; }; }; diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi index 098ad557fee3..e2b0da2c0bc7 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi @@ -106,6 +106,13 @@ }; }; + irda_regulator: irda-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpr3 3 GPIO_ACTIVE_HIGH>; + regulator-name = "irda_regulator"; + }; + sound { compatible = "samsung,tm2-audio"; audio-codec = <&wm5110>; @@ -298,6 +305,8 @@ status = "okay"; vddcore-supply = <&ldo6_reg>; vddio-supply = <&ldo7_reg>; + samsung,burst-clock-frequency = <512000000>; + samsung,esc-clock-frequency = <16000000>; samsung,pll-clock-frequency = <24000000>; pinctrl-names = "default"; pinctrl-0 = <&te_irq>; @@ -749,6 +758,19 @@ }; }; +&hsi2c_5 { + status = "okay"; + + stmfts: touchscreen@49 { + compatible = "st,stmfts"; + reg = <0x49>; + interrupt-parent = <&gpa1>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + avdd-supply = <&ldo30_reg>; + vdd-supply = <&ldo31_reg>; + }; +}; + &hsi2c_7 { status = "okay"; @@ -894,7 +916,7 @@ PIN(INPUT, gpa0-7, NONE, FAST_SR1); PIN(INPUT, gpa1-0, UP, FAST_SR1); - PIN(INPUT, gpa1-1, NONE, FAST_SR1); + PIN(INPUT, gpa1-1, UP, FAST_SR1); PIN(INPUT, gpa1-2, NONE, FAST_SR1); PIN(INPUT, gpa1-3, DOWN, FAST_SR1); PIN(INPUT, gpa1-4, DOWN, FAST_SR1); @@ -1074,7 +1096,6 @@ PIN(INPUT, gpg3-0, DOWN, FAST_SR1); PIN(INPUT, gpg3-1, DOWN, FAST_SR1); PIN(INPUT, gpg3-5, DOWN, FAST_SR1); - PIN(INPUT, gpg3-7, DOWN, FAST_SR1); }; }; @@ -1152,6 +1173,24 @@ }; }; +&spi_3 { + status = "okay"; + no-cs-readback; + + irled@0 { + compatible = "ir-spi-led"; + reg = <0x0>; + spi-max-frequency = <5000000>; + power-supply = <&irda_regulator>; + duty-cycle = <60>; + led-active-low; + + controller-data { + samsung,spi-feedback-delay = <0>; + }; + }; +}; + &timer { clock-frequency = <24000000>; }; diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts index dea0a6f5bc18..3ff95277a8ec 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts @@ -52,6 +52,18 @@ assigned-clock-rates = <250000000>, <400000000>; }; +&dsi { + panel@0 { + compatible = "samsung,s6e3ha2"; + reg = <0>; + vdd3-supply = <&ldo27_reg>; + vci-supply = <&ldo28_reg>; + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; + }; +}; + &hsi2c_9 { status = "okay"; @@ -76,3 +88,8 @@ regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; }; + +&stmfts { + touchscreen-size-x = <1439>; + touchscreen-size-y = <2559>; +}; diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts index 7891a31adc17..b73e1231a86f 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts @@ -52,6 +52,17 @@ assigned-clock-rates = <278000000>, <400000000>; }; +&dsi { + panel@0 { + compatible = "samsung,s6e3hf2"; + reg = <0>; + vdd3-supply = <&ldo27_reg>; + vci-supply = <&ldo28_reg>; + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; + }; +}; + &ldo31_reg { regulator-name = "TSP_VDD_1.8V_AP"; regulator-min-microvolt = <1800000>; @@ -63,3 +74,10 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; + +&stmfts { + touchscreen-size-x = <1599>; + touchscreen-size-y = <2559>; + touch-key-connected; + ledvdd-supply = <&ldo33_reg>; +}; diff --git a/arch/arm64/boot/dts/exynos/exynos5433.dtsi b/arch/arm64/boot/dts/exynos/exynos5433.dtsi index 16072c1c3ed3..727f36abf3d4 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433.dtsi +++ b/arch/arm64/boot/dts/exynos/exynos5433.dtsi @@ -119,43 +119,43 @@ compatible = "operating-points-v2"; opp-shared; - opp@400000000 { + opp-400000000 { opp-hz = /bits/ 64 <400000000>; opp-microvolt = <900000>; }; - opp@500000000 { + opp-500000000 { opp-hz = /bits/ 64 <500000000>; opp-microvolt = <925000>; }; - opp@600000000 { + opp-600000000 { opp-hz = /bits/ 64 <600000000>; opp-microvolt = <950000>; }; - opp@700000000 { + opp-700000000 { opp-hz = /bits/ 64 <700000000>; opp-microvolt = <975000>; }; - opp@800000000 { + opp-800000000 { opp-hz = /bits/ 64 <800000000>; opp-microvolt = <1000000>; }; - opp@900000000 { + opp-900000000 { opp-hz = /bits/ 64 <900000000>; opp-microvolt = <1050000>; }; - opp@1000000000 { + opp-1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <1075000>; }; - opp@1100000000 { + opp-1100000000 { opp-hz = /bits/ 64 <1100000000>; opp-microvolt = <1112500>; }; - opp@1200000000 { + opp-1200000000 { opp-hz = /bits/ 64 <1200000000>; opp-microvolt = <1112500>; }; - opp@1300000000 { + opp-1300000000 { opp-hz = /bits/ 64 <1300000000>; opp-microvolt = <1150000>; }; @@ -165,63 +165,63 @@ compatible = "operating-points-v2"; opp-shared; - opp@500000000 { + opp-500000000 { opp-hz = /bits/ 64 <500000000>; opp-microvolt = <900000>; }; - opp@600000000 { + opp-600000000 { opp-hz = /bits/ 64 <600000000>; opp-microvolt = <900000>; }; - opp@700000000 { + opp-700000000 { opp-hz = /bits/ 64 <700000000>; opp-microvolt = <912500>; }; - opp@800000000 { + opp-800000000 { opp-hz = /bits/ 64 <800000000>; opp-microvolt = <912500>; }; - opp@900000000 { + opp-900000000 { opp-hz = /bits/ 64 <900000000>; opp-microvolt = <937500>; }; - opp@1000000000 { + opp-1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <975000>; }; - opp@1100000000 { + opp-1100000000 { opp-hz = /bits/ 64 <1100000000>; opp-microvolt = <1012500>; }; - opp@1200000000 { + opp-1200000000 { opp-hz = /bits/ 64 <1200000000>; opp-microvolt = <1037500>; }; - opp@1300000000 { + opp-1300000000 { opp-hz = /bits/ 64 <1300000000>; opp-microvolt = <1062500>; }; - opp@1400000000 { + opp-1400000000 { opp-hz = /bits/ 64 <1400000000>; opp-microvolt = <1087500>; }; - opp@1500000000 { + opp-1500000000 { opp-hz = /bits/ 64 <1500000000>; opp-microvolt = <1125000>; }; - opp@1600000000 { + opp-1600000000 { opp-hz = /bits/ 64 <1600000000>; opp-microvolt = <1137500>; }; - opp@1700000000 { + opp-1700000000 { opp-hz = /bits/ 64 <1700000000>; opp-microvolt = <1175000>; }; - opp@1800000000 { + opp-1800000000 { opp-hz = /bits/ 64 <1800000000>; opp-microvolt = <1212500>; }; - opp@1900000000 { + opp-1900000000 { opp-hz = /bits/ 64 <1900000000>; opp-microvolt = <1262500>; }; diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 39db645b268e..72c4b525726f 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -5,9 +5,13 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-qds.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts index a619f6496a4c..17fae8112e4d 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts @@ -113,3 +113,7 @@ &sai2 { status = "okay"; }; + +&sata { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts index 14a67f1709e7..e2a93d53d3d8 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts @@ -126,3 +126,7 @@ &sai2 { status = "okay"; }; + +&sata { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts index 62c5c7123a15..ed77f6b0937b 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts @@ -57,3 +57,7 @@ &i2c0 { status = "okay"; }; + +&sata { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi index cffebb4b3df1..b497ac196ccc 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi @@ -42,7 +42,8 @@ * OTHER DEALINGS IN THE SOFTWARE. */ -#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/thermal/thermal.h> / { compatible = "fsl,ls1012a"; @@ -50,6 +51,15 @@ #address-cells = <2>; #size-cells = <2>; + aliases { + crypto = &crypto; + rtic_a = &rtic_a; + rtic_b = &rtic_b; + rtic_c = &rtic_c; + rtic_d = &rtic_d; + sec_mon = &sec_mon; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -113,6 +123,95 @@ big-endian; }; + crypto: crypto@1700000 { + compatible = "fsl,sec-v5.4", "fsl,sec-v5.0", + "fsl,sec-v4.0"; + fsl,sec-era = <8>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x00 0x1700000 0x100000>; + reg = <0x00 0x1700000 0x0 0x100000>; + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; + + sec_jr0: jr@10000 { + compatible = "fsl,sec-v5.4-job-ring", + "fsl,sec-v5.0-job-ring", + "fsl,sec-v4.0-job-ring"; + reg = <0x10000 0x10000>; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + }; + + sec_jr1: jr@20000 { + compatible = "fsl,sec-v5.4-job-ring", + "fsl,sec-v5.0-job-ring", + "fsl,sec-v4.0-job-ring"; + reg = <0x20000 0x10000>; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + }; + + sec_jr2: jr@30000 { + compatible = "fsl,sec-v5.4-job-ring", + "fsl,sec-v5.0-job-ring", + "fsl,sec-v4.0-job-ring"; + reg = <0x30000 0x10000>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + }; + + sec_jr3: jr@40000 { + compatible = "fsl,sec-v5.4-job-ring", + "fsl,sec-v5.0-job-ring", + "fsl,sec-v4.0-job-ring"; + reg = <0x40000 0x10000>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + }; + + rtic@60000 { + compatible = "fsl,sec-v5.4-rtic", + "fsl,sec-v5.0-rtic", + "fsl,sec-v4.0-rtic"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x60000 0x100 0x60e00 0x18>; + ranges = <0x0 0x60100 0x500>; + + rtic_a: rtic-a@0 { + compatible = "fsl,sec-v5.4-rtic-memory", + "fsl,sec-v5.0-rtic-memory", + "fsl,sec-v4.0-rtic-memory"; + reg = <0x00 0x20 0x100 0x100>; + }; + + rtic_b: rtic-b@20 { + compatible = "fsl,sec-v5.4-rtic-memory", + "fsl,sec-v5.0-rtic-memory", + "fsl,sec-v4.0-rtic-memory"; + reg = <0x20 0x20 0x200 0x100>; + }; + + rtic_c: rtic-c@40 { + compatible = "fsl,sec-v5.4-rtic-memory", + "fsl,sec-v5.0-rtic-memory", + "fsl,sec-v4.0-rtic-memory"; + reg = <0x40 0x20 0x300 0x100>; + }; + + rtic_d: rtic-d@60 { + compatible = "fsl,sec-v5.4-rtic-memory", + "fsl,sec-v5.0-rtic-memory", + "fsl,sec-v4.0-rtic-memory"; + reg = <0x60 0x20 0x400 0x100>; + }; + }; + }; + + sec_mon: sec_mon@1e90000 { + compatible = "fsl,sec-v5.4-mon", "fsl,sec-v5.0-mon", + "fsl,sec-v4.0-mon"; + reg = <0x0 0x1e90000 0x0 0x10000>; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; + }; + dcfg: dcfg@1ee0000 { compatible = "fsl,ls1012a-dcfg", "syscon"; @@ -127,6 +226,82 @@ clocks = <&sysclk>; }; + tmu: tmu@1f00000 { + compatible = "fsl,qoriq-tmu"; + reg = <0x0 0x1f00000 0x0 0x10000>; + interrupts = <0 33 0x4>; + fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>; + fsl,tmu-calibration = <0x00000000 0x00000026 + 0x00000001 0x0000002d + 0x00000002 0x00000032 + 0x00000003 0x00000039 + 0x00000004 0x0000003f + 0x00000005 0x00000046 + 0x00000006 0x0000004d + 0x00000007 0x00000054 + 0x00000008 0x0000005a + 0x00000009 0x00000061 + 0x0000000a 0x0000006a + 0x0000000b 0x00000071 + + 0x00010000 0x00000025 + 0x00010001 0x0000002c + 0x00010002 0x00000035 + 0x00010003 0x0000003d + 0x00010004 0x00000045 + 0x00010005 0x0000004e + 0x00010006 0x00000057 + 0x00010007 0x00000061 + 0x00010008 0x0000006b + 0x00010009 0x00000076 + + 0x00020000 0x00000029 + 0x00020001 0x00000033 + 0x00020002 0x0000003d + 0x00020003 0x00000049 + 0x00020004 0x00000056 + 0x00020005 0x00000061 + 0x00020006 0x0000006d + + 0x00030000 0x00000021 + 0x00030001 0x0000002a + 0x00030002 0x0000003c + 0x00030003 0x0000004e>; + big-endian; + #thermal-sensor-cells = <1>; + }; + + thermal-zones { + cpu_thermal: cpu-thermal { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 0>; + + trips { + cpu_alert: cpu-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu_crit: cpu-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_alert>; + cooling-device = + <&cpu0 THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>; + }; + }; + }; + }; + i2c0: i2c@2180000 { compatible = "fsl,vf610-i2c"; #address-cells = <1>; @@ -238,9 +413,12 @@ sata: sata@3200000 { compatible = "fsl,ls1012a-ahci", "fsl,ls1043a-ahci"; - reg = <0x0 0x3200000 0x0 0x10000>; + reg = <0x0 0x3200000 0x0 0x10000>, + <0x0 0x20140520 0x0 0x4>; + reg-names = "ahci", "sata-ecc"; interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clockgen 4 0>; + dma-coherent; status = "disabled"; }; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi index ec13a6ecb754..45cface08cbb 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi @@ -582,7 +582,9 @@ sata: sata@3200000 { compatible = "fsl,ls1043a-ahci"; - reg = <0x0 0x3200000 0x0 0x10000>; + reg = <0x0 0x3200000 0x0 0x10000>, + <0x0 0x20140520 0x0 0x4>; + reg-names = "ahci", "sata-ecc"; interrupts = <0 69 0x4>; clocks = <&clockgen 4 0>; dma-coherent; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi index 4a164b801882..f4b8b7edaf9d 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi @@ -587,7 +587,9 @@ sata: sata@3200000 { compatible = "fsl,ls1046a-ahci"; - reg = <0x0 0x3200000 0x0 0x10000>; + reg = <0x0 0x3200000 0x0 0x10000>, + <0x0 0x20140520 0x0 0x4>; + reg-names = "ahci", "sata-ecc"; interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clockgen 4 1>; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts new file mode 100644 index 000000000000..8c3cae530f8f --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts @@ -0,0 +1,123 @@ +/* + * Device Tree file for NXP LS1088A QDS Board. + * + * Copyright 2017 NXP + * + * Harninder Rai <harninder.rai@nxp.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "fsl-ls1088a.dtsi" + +/ { + model = "LS1088A QDS Board"; + compatible = "fsl,ls1088a-qds", "fsl,ls1088a"; +}; + +&i2c0 { + status = "okay"; + + i2c-switch@77 { + compatible = "nxp,pca9547"; + reg = <0x77>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2>; + + ina220@40 { + compatible = "ti,ina220"; + reg = <0x40>; + shunt-resistor = <1000>; + }; + + ina220@41 { + compatible = "ti,ina220"; + reg = <0x41>; + shunt-resistor = <1000>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3>; + + temp-sensor@4c { + compatible = "adi,adt7461a"; + reg = <0x4c>; + }; + + rtc@51 { + compatible = "nxp,pcf2129"; + reg = <0x51>; + /* IRQ10_B */ + interrupts = <0 150 IRQ_TYPE_LEVEL_HIGH>; + }; + + eeprom@56 { + compatible = "atmel,24c512"; + reg = <0x56>; + }; + + eeprom@57 { + compatible = "atmel,24c512"; + reg = <0x57>; + }; + }; + }; +}; + +&duart0 { + status = "okay"; +}; + +&duart1 { + status = "okay"; +}; + +&sata { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts new file mode 100644 index 000000000000..8a04fbb25cb4 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts @@ -0,0 +1,107 @@ +/* + * Device Tree file for NXP LS1088A RDB Board. + * + * Copyright 2017 NXP + * + * Harninder Rai <harninder.rai@nxp.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "fsl-ls1088a.dtsi" + +/ { + model = "L1088A RDB Board"; + compatible = "fsl,ls1088a-rdb", "fsl,ls1088a"; +}; + +&i2c0 { + status = "okay"; + + i2c-switch@77 { + compatible = "nxp,pca9547"; + reg = <0x77>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2>; + + ina220@40 { + compatible = "ti,ina220"; + reg = <0x40>; + shunt-resistor = <1000>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3>; + + temp-sensor@4c { + compatible = "adi,adt7461a"; + reg = <0x4c>; + }; + + rtc@51 { + compatible = "nxp,pcf2129"; + reg = <0x51>; + /* IRQ10_B */ + interrupts = <0 150 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; +}; + +&duart0 { + status = "okay"; +}; + +&duart1 { + status = "okay"; +}; + +&sata { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi new file mode 100644 index 000000000000..2946fd797121 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi @@ -0,0 +1,275 @@ +/* + * Device Tree Include file for NXP Layerscape-1088A family SoC. + * + * Copyright 2017 NXP + * + * Harninder Rai <harninder.rai@nxp.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + compatible = "fsl,ls1088a"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + /* We have 2 clusters having 4 Cortex-A53 cores each */ + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0>; + clocks = <&clockgen 1 0>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1>; + clocks = <&clockgen 1 0>; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x2>; + clocks = <&clockgen 1 0>; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x3>; + clocks = <&clockgen 1 0>; + }; + + cpu4: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x100>; + clocks = <&clockgen 1 1>; + }; + + cpu5: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x101>; + clocks = <&clockgen 1 1>; + }; + + cpu6: cpu@102 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x102>; + clocks = <&clockgen 1 1>; + }; + + cpu7: cpu@103 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x103>; + clocks = <&clockgen 1 1>; + }; + }; + + gic: interrupt-controller@6000000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */ + <0x0 0x06100000 0 0x100000>, /* GICR(RD_base+SGI_base)*/ + <0x0 0x0c0c0000 0 0x2000>, /* GICC */ + <0x0 0x0c0d0000 0 0x1000>, /* GICH */ + <0x0 0x0c0e0000 0 0x20000>; /* GICV */ + interrupts = <1 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <1 13 IRQ_TYPE_LEVEL_LOW>,/* Physical Secure PPI */ + <1 14 IRQ_TYPE_LEVEL_LOW>,/* Physical Non-Secure PPI */ + <1 11 IRQ_TYPE_LEVEL_LOW>,/* Virtual PPI */ + <1 10 IRQ_TYPE_LEVEL_LOW>;/* Hypervisor PPI */ + }; + + sysclk: sysclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + clock-output-names = "sysclk"; + }; + + soc { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clockgen: clocking@1300000 { + compatible = "fsl,ls1088a-clockgen"; + reg = <0 0x1300000 0 0xa0000>; + #clock-cells = <2>; + clocks = <&sysclk>; + }; + + duart0: serial@21c0500 { + compatible = "fsl,ns16550", "ns16550a"; + reg = <0x0 0x21c0500 0x0 0x100>; + clocks = <&clockgen 4 3>; + interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + duart1: serial@21c0600 { + compatible = "fsl,ns16550", "ns16550a"; + reg = <0x0 0x21c0600 0x0 0x100>; + clocks = <&clockgen 4 3>; + interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + gpio0: gpio@2300000 { + compatible = "fsl,qoriq-gpio"; + reg = <0x0 0x2300000 0x0 0x10000>; + interrupts = <0 36 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio@2310000 { + compatible = "fsl,qoriq-gpio"; + reg = <0x0 0x2310000 0x0 0x10000>; + interrupts = <0 36 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio@2320000 { + compatible = "fsl,qoriq-gpio"; + reg = <0x0 0x2320000 0x0 0x10000>; + interrupts = <0 37 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio@2330000 { + compatible = "fsl,qoriq-gpio"; + reg = <0x0 0x2330000 0x0 0x10000>; + interrupts = <0 37 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + ifc: ifc@2240000 { + compatible = "fsl,ifc", "simple-bus"; + reg = <0x0 0x2240000 0x0 0x20000>; + interrupts = <0 21 IRQ_TYPE_LEVEL_HIGH>; + little-endian; + #address-cells = <2>; + #size-cells = <1>; + + ranges = <0 0 0x5 0x80000000 0x08000000 + 2 0 0x5 0x30000000 0x00010000 + 3 0 0x5 0x20000000 0x00010000>; + status = "disabled"; + }; + + i2c0: i2c@2000000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2000000 0x0 0x10000>; + interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 3>; + status = "disabled"; + }; + + i2c1: i2c@2010000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2010000 0x0 0x10000>; + interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 3>; + status = "disabled"; + }; + + i2c2: i2c@2020000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2020000 0x0 0x10000>; + interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 3>; + status = "disabled"; + }; + + i2c3: i2c@2030000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2030000 0x0 0x10000>; + interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 3>; + status = "disabled"; + }; + + sata: sata@3200000 { + compatible = "fsl,ls1088a-ahci", "fsl,ls1043a-ahci"; + reg = <0x0 0x3200000 0x0 0x10000>; + interrupts = <0 133 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 3>; + status = "disabled"; + }; + }; + +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts index 8bc1f8f6fcfc..c1e76dfca48e 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts @@ -1,8 +1,9 @@ /* * Device Tree file for Freescale LS2080a QDS Board. * - * Copyright (C) 2015, Freescale Semiconductor + * Copyright (C) 2015-17, Freescale Semiconductor * + * Abhimanyu Saini <abhimanyu.saini@nxp.com> * Bhupesh Sharma <bhupesh.sharma@freescale.com> * * This file is dual-licensed: you can use it either under the terms @@ -47,6 +48,7 @@ /dts-v1/; #include "fsl-ls2080a.dtsi" +#include "fsl-ls208xa-qds.dtsi" / { model = "Freescale Layerscape 2080a QDS Board"; @@ -61,154 +63,3 @@ stdout-path = "serial0:115200n8"; }; }; - -&esdhc { - status = "okay"; -}; - -&ifc { - status = "okay"; - #address-cells = <2>; - #size-cells = <1>; - ranges = <0x0 0x0 0x5 0x80000000 0x08000000 - 0x2 0x0 0x5 0x30000000 0x00010000 - 0x3 0x0 0x5 0x20000000 0x00010000>; - - nor@0,0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "cfi-flash"; - reg = <0x0 0x0 0x8000000>; - bank-width = <2>; - device-width = <1>; - }; - - nand@2,0 { - compatible = "fsl,ifc-nand"; - reg = <0x2 0x0 0x10000>; - }; - - cpld@3,0 { - reg = <0x3 0x0 0x10000>; - compatible = "fsl,ls2080aqds-fpga", "fsl,fpga-qixis"; - }; -}; - -&i2c0 { - status = "okay"; - pca9547@77 { - compatible = "nxp,pca9547"; - reg = <0x77>; - #address-cells = <1>; - #size-cells = <0>; - i2c@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0x00>; - rtc@68 { - compatible = "dallas,ds3232"; - reg = <0x68>; - }; - }; - - i2c@2 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0x02>; - - ina220@40 { - compatible = "ti,ina220"; - reg = <0x40>; - shunt-resistor = <500>; - }; - - ina220@41 { - compatible = "ti,ina220"; - reg = <0x41>; - shunt-resistor = <1000>; - }; - }; - - i2c@3 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0x3>; - - adt7481@4c { - compatible = "adi,adt7461"; - reg = <0x4c>; - }; - }; - }; -}; - -&i2c1 { - status = "disabled"; -}; - -&i2c2 { - status = "disabled"; -}; - -&i2c3 { - status = "disabled"; -}; - -&dspi { - status = "okay"; - dflash0: n25q128a { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,m25p80"; - spi-max-frequency = <3000000>; - reg = <0>; - }; - dflash1: sst25wf040b { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,m25p80"; - spi-max-frequency = <3000000>; - reg = <1>; - }; - dflash2: en25s64 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,m25p80"; - spi-max-frequency = <3000000>; - reg = <2>; - }; -}; - -&qspi { - status = "okay"; - flash0: s25fl256s1@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,m25p80"; - spi-max-frequency = <20000000>; - reg = <0>; - }; - flash2: s25fl256s1@2 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,m25p80"; - spi-max-frequency = <20000000>; - reg = <0>; - }; -}; - -&sata0 { - status = "okay"; -}; - -&sata1 { - status = "okay"; -}; - -&usb0 { - status = "okay"; -}; - -&usb1 { - status = "okay"; -}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts index 2ff46ca450b1..18ad19587311 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts @@ -1,8 +1,9 @@ /* * Device Tree file for Freescale LS2080a RDB Board. * - * Copyright (C) 2015, Freescale Semiconductor + * Copyright (C) 2016-17, Freescale Semiconductor * + * Abhimanyu Saini <abhimanyu.saini@nxp.com> * Bhupesh Sharma <bhupesh.sharma@freescale.com> * * This file is dual-licensed: you can use it either under the terms @@ -47,6 +48,7 @@ /dts-v1/; #include "fsl-ls2080a.dtsi" +#include "fsl-ls208xa-rdb.dtsi" / { model = "Freescale Layerscape 2080a RDB Board"; @@ -61,109 +63,3 @@ stdout-path = "serial1:115200n8"; }; }; - -&esdhc { - status = "okay"; -}; - -&ifc { - status = "okay"; - #address-cells = <2>; - #size-cells = <1>; - ranges = <0x0 0x0 0x5 0x80000000 0x08000000 - 0x2 0x0 0x5 0x30000000 0x00010000 - 0x3 0x0 0x5 0x20000000 0x00010000>; - - nor@0,0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "cfi-flash"; - reg = <0x0 0x0 0x8000000>; - bank-width = <2>; - device-width = <1>; - }; - - nand@2,0 { - compatible = "fsl,ifc-nand"; - reg = <0x2 0x0 0x10000>; - }; - - cpld@3,0 { - reg = <0x3 0x0 0x10000>; - compatible = "fsl,ls2080aqds-fpga", "fsl,fpga-qixis"; - }; - -}; - -&i2c0 { - status = "okay"; - pca9547@75 { - compatible = "nxp,pca9547"; - reg = <0x75>; - #address-cells = <1>; - #size-cells = <0>; - i2c@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0x01>; - rtc@68 { - compatible = "dallas,ds3232"; - reg = <0x68>; - }; - }; - - i2c@3 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0x3>; - - adt7481@4c { - compatible = "adi,adt7461"; - reg = <0x4c>; - }; - }; - }; -}; - -&i2c1 { - status = "disabled"; -}; - -&i2c2 { - status = "disabled"; -}; - -&i2c3 { - status = "disabled"; -}; - -&dspi { - status = "okay"; - dflash0: n25q512a { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,m25p80"; - spi-max-frequency = <3000000>; - reg = <0>; - }; -}; - -&qspi { - status = "disabled"; -}; - -&sata0 { - status = "okay"; -}; - -&sata1 { - status = "okay"; -}; - -&usb0 { - status = "okay"; -}; - -&usb1 { - status = "okay"; -}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi index e5935f28848c..46a26c021421 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi @@ -1,8 +1,9 @@ /* * Device Tree Include file for Freescale Layerscape-2080A family SoC. * - * Copyright (C) 2014-2015, Freescale Semiconductor + * Copyright (C) 2014-2016, Freescale Semiconductor * + * Abhimanyu Saini <abhimanyu.saini@nxp.com> * Bhupesh Sharma <bhupesh.sharma@freescale.com> * * This file is dual-licensed: you can use it either under the terms @@ -44,802 +45,122 @@ * OTHER DEALINGS IN THE SOFTWARE. */ -#include <dt-bindings/thermal/thermal.h> +#include "fsl-ls208xa.dtsi" -/ { - compatible = "fsl,ls2080a"; - interrupt-parent = <&gic>; - #address-cells = <2>; - #size-cells = <2>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - /* - * We expect the enable-method for cpu's to be "psci", but this - * is dependent on the SoC FW, which will fill this in. - * - * Currently supported enable-method is psci v0.2 - */ - - /* We have 4 clusters having 2 Cortex-A57 cores each */ - cpu0: cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x0>; - clocks = <&clockgen 1 0>; - next-level-cache = <&cluster0_l2>; - #cooling-cells = <2>; - }; - - cpu1: cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x1>; - clocks = <&clockgen 1 0>; - next-level-cache = <&cluster0_l2>; - }; - - cpu2: cpu@100 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x100>; - clocks = <&clockgen 1 1>; - next-level-cache = <&cluster1_l2>; - #cooling-cells = <2>; - }; - - cpu3: cpu@101 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x101>; - clocks = <&clockgen 1 1>; - next-level-cache = <&cluster1_l2>; - }; - - cpu4: cpu@200 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x200>; - clocks = <&clockgen 1 2>; - next-level-cache = <&cluster2_l2>; - #cooling-cells = <2>; - }; - - cpu5: cpu@201 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x201>; - clocks = <&clockgen 1 2>; - next-level-cache = <&cluster2_l2>; - }; - - cpu6: cpu@300 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x300>; - clocks = <&clockgen 1 3>; - next-level-cache = <&cluster3_l2>; - #cooling-cells = <2>; - }; - - cpu7: cpu@301 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x301>; - clocks = <&clockgen 1 3>; - next-level-cache = <&cluster3_l2>; - }; - - cluster0_l2: l2-cache0 { - compatible = "cache"; - }; - - cluster1_l2: l2-cache1 { - compatible = "cache"; - }; - - cluster2_l2: l2-cache2 { - compatible = "cache"; - }; - - cluster3_l2: l2-cache3 { - compatible = "cache"; - }; +&cpu { + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x0>; + clocks = <&clockgen 1 0>; + next-level-cache = <&cluster0_l2>; + #cooling-cells = <2>; }; - memory@80000000 { - device_type = "memory"; - reg = <0x00000000 0x80000000 0 0x80000000>; - /* DRAM space - 1, size : 2 GB DRAM */ + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x1>; + clocks = <&clockgen 1 0>; + next-level-cache = <&cluster0_l2>; }; - sysclk: sysclk { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <100000000>; - clock-output-names = "sysclk"; + cpu2: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x100>; + clocks = <&clockgen 1 1>; + next-level-cache = <&cluster1_l2>; + #cooling-cells = <2>; }; - gic: interrupt-controller@6000000 { - compatible = "arm,gic-v3"; - reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */ - <0x0 0x06100000 0 0x100000>, /* GICR (RD_base + SGI_base) */ - <0x0 0x0c0c0000 0 0x2000>, /* GICC */ - <0x0 0x0c0d0000 0 0x1000>, /* GICH */ - <0x0 0x0c0e0000 0 0x20000>; /* GICV */ - #interrupt-cells = <3>; - #address-cells = <2>; - #size-cells = <2>; - ranges; - interrupt-controller; - interrupts = <1 9 0x4>; - - its: gic-its@6020000 { - compatible = "arm,gic-v3-its"; - msi-controller; - reg = <0x0 0x6020000 0 0x20000>; - }; + cpu3: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x101>; + clocks = <&clockgen 1 1>; + next-level-cache = <&cluster1_l2>; }; - rstcr: syscon@1e60000 { - compatible = "fsl,ls2080a-rstcr", "syscon"; - reg = <0x0 0x1e60000 0x0 0x4>; + cpu4: cpu@200 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x200>; + clocks = <&clockgen 1 2>; + next-level-cache = <&cluster2_l2>; + #cooling-cells = <2>; }; - reboot { - compatible ="syscon-reboot"; - regmap = <&rstcr>; - offset = <0x0>; - mask = <0x2>; + cpu5: cpu@201 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x201>; + clocks = <&clockgen 1 2>; + next-level-cache = <&cluster2_l2>; }; - timer { - compatible = "arm,armv8-timer"; - interrupts = <1 13 4>, /* Physical Secure PPI, active-low */ - <1 14 4>, /* Physical Non-Secure PPI, active-low */ - <1 11 4>, /* Virtual PPI, active-low */ - <1 10 4>; /* Hypervisor PPI, active-low */ - fsl,erratum-a008585; + cpu6: cpu@300 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x300>; + clocks = <&clockgen 1 3>; + next-level-cache = <&cluster3_l2>; + #cooling-cells = <2>; }; - pmu { - compatible = "arm,armv8-pmuv3"; - interrupts = <1 7 0x8>; /* PMU PPI, Level low type */ + cpu7: cpu@301 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x301>; + clocks = <&clockgen 1 3>; + next-level-cache = <&cluster3_l2>; }; - soc { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - clockgen: clocking@1300000 { - compatible = "fsl,ls2080a-clockgen"; - reg = <0 0x1300000 0 0xa0000>; - #clock-cells = <2>; - clocks = <&sysclk>; - }; - - dcfg: dcfg@1e00000 { - compatible = "fsl,ls2080a-dcfg", "syscon"; - reg = <0x0 0x1e00000 0x0 0x10000>; - little-endian; - }; - - tmu: tmu@1f80000 { - compatible = "fsl,qoriq-tmu"; - reg = <0x0 0x1f80000 0x0 0x10000>; - interrupts = <0 23 0x4>; - fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>; - fsl,tmu-calibration = <0x00000000 0x00000026 - 0x00000001 0x0000002d - 0x00000002 0x00000032 - 0x00000003 0x00000039 - 0x00000004 0x0000003f - 0x00000005 0x00000046 - 0x00000006 0x0000004d - 0x00000007 0x00000054 - 0x00000008 0x0000005a - 0x00000009 0x00000061 - 0x0000000a 0x0000006a - 0x0000000b 0x00000071 - - 0x00010000 0x00000025 - 0x00010001 0x0000002c - 0x00010002 0x00000035 - 0x00010003 0x0000003d - 0x00010004 0x00000045 - 0x00010005 0x0000004e - 0x00010006 0x00000057 - 0x00010007 0x00000061 - 0x00010008 0x0000006b - 0x00010009 0x00000076 - - 0x00020000 0x00000029 - 0x00020001 0x00000033 - 0x00020002 0x0000003d - 0x00020003 0x00000049 - 0x00020004 0x00000056 - 0x00020005 0x00000061 - 0x00020006 0x0000006d - - 0x00030000 0x00000021 - 0x00030001 0x0000002a - 0x00030002 0x0000003c - 0x00030003 0x0000004e>; - little-endian; - #thermal-sensor-cells = <1>; - }; - - thermal-zones { - cpu_thermal: cpu-thermal { - polling-delay-passive = <1000>; - polling-delay = <5000>; - - thermal-sensors = <&tmu 4>; - - trips { - cpu_alert: cpu-alert { - temperature = <75000>; - hysteresis = <2000>; - type = "passive"; - }; - cpu_crit: cpu-crit { - temperature = <85000>; - hysteresis = <2000>; - type = "critical"; - }; - }; - - cooling-maps { - map0 { - trip = <&cpu_alert>; - cooling-device = - <&cpu0 THERMAL_NO_LIMIT - THERMAL_NO_LIMIT>; - }; - map1 { - trip = <&cpu_alert>; - cooling-device = - <&cpu2 THERMAL_NO_LIMIT - THERMAL_NO_LIMIT>; - }; - map2 { - trip = <&cpu_alert>; - cooling-device = - <&cpu4 THERMAL_NO_LIMIT - THERMAL_NO_LIMIT>; - }; - map3 { - trip = <&cpu_alert>; - cooling-device = - <&cpu6 THERMAL_NO_LIMIT - THERMAL_NO_LIMIT>; - }; - }; - }; - }; - - serial0: serial@21c0500 { - compatible = "fsl,ns16550", "ns16550a"; - reg = <0x0 0x21c0500 0x0 0x100>; - clocks = <&clockgen 4 3>; - interrupts = <0 32 0x4>; /* Level high type */ - }; - - serial1: serial@21c0600 { - compatible = "fsl,ns16550", "ns16550a"; - reg = <0x0 0x21c0600 0x0 0x100>; - clocks = <&clockgen 4 3>; - interrupts = <0 32 0x4>; /* Level high type */ - }; - - cluster1_core0_watchdog: wdt@c000000 { - compatible = "arm,sp805-wdt", "arm,primecell"; - reg = <0x0 0xc000000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; - clock-names = "apb_pclk", "wdog_clk"; - }; - - cluster1_core1_watchdog: wdt@c010000 { - compatible = "arm,sp805-wdt", "arm,primecell"; - reg = <0x0 0xc010000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; - clock-names = "apb_pclk", "wdog_clk"; - }; - - cluster2_core0_watchdog: wdt@c100000 { - compatible = "arm,sp805-wdt", "arm,primecell"; - reg = <0x0 0xc100000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; - clock-names = "apb_pclk", "wdog_clk"; - }; - - cluster2_core1_watchdog: wdt@c110000 { - compatible = "arm,sp805-wdt", "arm,primecell"; - reg = <0x0 0xc110000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; - clock-names = "apb_pclk", "wdog_clk"; - }; - - cluster3_core0_watchdog: wdt@c200000 { - compatible = "arm,sp805-wdt", "arm,primecell"; - reg = <0x0 0xc200000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; - clock-names = "apb_pclk", "wdog_clk"; - }; - - cluster3_core1_watchdog: wdt@c210000 { - compatible = "arm,sp805-wdt", "arm,primecell"; - reg = <0x0 0xc210000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; - clock-names = "apb_pclk", "wdog_clk"; - }; - - cluster4_core0_watchdog: wdt@c300000 { - compatible = "arm,sp805-wdt", "arm,primecell"; - reg = <0x0 0xc300000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; - clock-names = "apb_pclk", "wdog_clk"; - }; - - cluster4_core1_watchdog: wdt@c310000 { - compatible = "arm,sp805-wdt", "arm,primecell"; - reg = <0x0 0xc310000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; - clock-names = "apb_pclk", "wdog_clk"; - }; - - fsl_mc: fsl-mc@80c000000 { - compatible = "fsl,qoriq-mc"; - reg = <0x00000008 0x0c000000 0 0x40>, /* MC portal base */ - <0x00000000 0x08340000 0 0x40000>; /* MC control reg */ - msi-parent = <&its>; - #address-cells = <3>; - #size-cells = <1>; - - /* - * Region type 0x0 - MC portals - * Region type 0x1 - QBMAN portals - */ - ranges = <0x0 0x0 0x0 0x8 0x0c000000 0x4000000 - 0x1 0x0 0x0 0x8 0x18000000 0x8000000>; - - /* - * Define the maximum number of MACs present on the SoC. - */ - dpmacs { - #address-cells = <1>; - #size-cells = <0>; - - dpmac1: dpmac@1 { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0x1>; - }; - - dpmac2: dpmac@2 { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0x2>; - }; - - dpmac3: dpmac@3 { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0x3>; - }; - - dpmac4: dpmac@4 { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0x4>; - }; - - dpmac5: dpmac@5 { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0x5>; - }; - - dpmac6: dpmac@6 { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0x6>; - }; - - dpmac7: dpmac@7 { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0x7>; - }; - - dpmac8: dpmac@8 { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0x8>; - }; - - dpmac9: dpmac@9 { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0x9>; - }; - - dpmac10: dpmac@a { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0xa>; - }; - - dpmac11: dpmac@b { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0xb>; - }; - - dpmac12: dpmac@c { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0xc>; - }; - - dpmac13: dpmac@d { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0xd>; - }; - - dpmac14: dpmac@e { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0xe>; - }; - - dpmac15: dpmac@f { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0xf>; - }; - - dpmac16: dpmac@10 { - compatible = "fsl,qoriq-mc-dpmac"; - reg = <0x10>; - }; - }; - }; - - smmu: iommu@5000000 { - compatible = "arm,mmu-500"; - reg = <0 0x5000000 0 0x800000>; - #global-interrupts = <12>; - interrupts = <0 13 4>, /* global secure fault */ - <0 14 4>, /* combined secure interrupt */ - <0 15 4>, /* global non-secure fault */ - <0 16 4>, /* combined non-secure interrupt */ - /* performance counter interrupts 0-7 */ - <0 211 4>, <0 212 4>, - <0 213 4>, <0 214 4>, - <0 215 4>, <0 216 4>, - <0 217 4>, <0 218 4>, - /* per context interrupt, 64 interrupts */ - <0 146 4>, <0 147 4>, - <0 148 4>, <0 149 4>, - <0 150 4>, <0 151 4>, - <0 152 4>, <0 153 4>, - <0 154 4>, <0 155 4>, - <0 156 4>, <0 157 4>, - <0 158 4>, <0 159 4>, - <0 160 4>, <0 161 4>, - <0 162 4>, <0 163 4>, - <0 164 4>, <0 165 4>, - <0 166 4>, <0 167 4>, - <0 168 4>, <0 169 4>, - <0 170 4>, <0 171 4>, - <0 172 4>, <0 173 4>, - <0 174 4>, <0 175 4>, - <0 176 4>, <0 177 4>, - <0 178 4>, <0 179 4>, - <0 180 4>, <0 181 4>, - <0 182 4>, <0 183 4>, - <0 184 4>, <0 185 4>, - <0 186 4>, <0 187 4>, - <0 188 4>, <0 189 4>, - <0 190 4>, <0 191 4>, - <0 192 4>, <0 193 4>, - <0 194 4>, <0 195 4>, - <0 196 4>, <0 197 4>, - <0 198 4>, <0 199 4>, - <0 200 4>, <0 201 4>, - <0 202 4>, <0 203 4>, - <0 204 4>, <0 205 4>, - <0 206 4>, <0 207 4>, - <0 208 4>, <0 209 4>; - mmu-masters = <&fsl_mc 0x300 0>; - }; - - dspi: dspi@2100000 { - status = "disabled"; - compatible = "fsl,ls2080a-dspi", "fsl,ls2085a-dspi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2100000 0x0 0x10000>; - interrupts = <0 26 0x4>; /* Level high type */ - clocks = <&clockgen 4 3>; - clock-names = "dspi"; - spi-num-chipselects = <5>; - bus-num = <0>; - }; - - esdhc: esdhc@2140000 { - status = "disabled"; - compatible = "fsl,ls2080a-esdhc", "fsl,esdhc"; - reg = <0x0 0x2140000 0x0 0x10000>; - interrupts = <0 28 0x4>; /* Level high type */ - clock-frequency = <0>; /* Updated by bootloader */ - voltage-ranges = <1800 1800 3300 3300>; - sdhci,auto-cmd12; - little-endian; - bus-width = <4>; - }; - - gpio0: gpio@2300000 { - compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio"; - reg = <0x0 0x2300000 0x0 0x10000>; - interrupts = <0 36 0x4>; /* Level high type */ - gpio-controller; - little-endian; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio1: gpio@2310000 { - compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio"; - reg = <0x0 0x2310000 0x0 0x10000>; - interrupts = <0 36 0x4>; /* Level high type */ - gpio-controller; - little-endian; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio2: gpio@2320000 { - compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio"; - reg = <0x0 0x2320000 0x0 0x10000>; - interrupts = <0 37 0x4>; /* Level high type */ - gpio-controller; - little-endian; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio3: gpio@2330000 { - compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio"; - reg = <0x0 0x2330000 0x0 0x10000>; - interrupts = <0 37 0x4>; /* Level high type */ - gpio-controller; - little-endian; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - i2c0: i2c@2000000 { - status = "disabled"; - compatible = "fsl,vf610-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2000000 0x0 0x10000>; - interrupts = <0 34 0x4>; /* Level high type */ - clock-names = "i2c"; - clocks = <&clockgen 4 3>; - }; - - i2c1: i2c@2010000 { - status = "disabled"; - compatible = "fsl,vf610-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2010000 0x0 0x10000>; - interrupts = <0 34 0x4>; /* Level high type */ - clock-names = "i2c"; - clocks = <&clockgen 4 3>; - }; - - i2c2: i2c@2020000 { - status = "disabled"; - compatible = "fsl,vf610-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2020000 0x0 0x10000>; - interrupts = <0 35 0x4>; /* Level high type */ - clock-names = "i2c"; - clocks = <&clockgen 4 3>; - }; - - i2c3: i2c@2030000 { - status = "disabled"; - compatible = "fsl,vf610-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x2030000 0x0 0x10000>; - interrupts = <0 35 0x4>; /* Level high type */ - clock-names = "i2c"; - clocks = <&clockgen 4 3>; - }; - - ifc: ifc@2240000 { - compatible = "fsl,ifc", "simple-bus"; - reg = <0x0 0x2240000 0x0 0x20000>; - interrupts = <0 21 0x4>; /* Level high type */ - little-endian; - #address-cells = <2>; - #size-cells = <1>; - - ranges = <0 0 0x5 0x80000000 0x08000000 - 2 0 0x5 0x30000000 0x00010000 - 3 0 0x5 0x20000000 0x00010000>; - }; - - qspi: quadspi@20c0000 { - status = "disabled"; - compatible = "fsl,ls2080a-qspi", "fsl,ls1021a-qspi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0 0x20c0000 0x0 0x10000>, - <0x0 0x20000000 0x0 0x10000000>; - reg-names = "QuadSPI", "QuadSPI-memory"; - interrupts = <0 25 0x4>; /* Level high type */ - clocks = <&clockgen 4 3>, <&clockgen 4 3>; - clock-names = "qspi_en", "qspi"; - }; + cluster0_l2: l2-cache0 { + compatible = "cache"; + }; - pcie@3400000 { - compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", - "snps,dw-pcie"; - reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */ - 0x10 0x00000000 0x0 0x00002000>; /* configuration space */ - reg-names = "regs", "config"; - interrupts = <0 108 0x4>; /* Level high type */ - interrupt-names = "intr"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - dma-coherent; - num-lanes = <4>; - bus-range = <0x0 0xff>; - ranges = <0x81000000 0x0 0x00000000 0x10 0x00010000 0x0 0x00010000 /* downstream I/O */ - 0x82000000 0x0 0x40000000 0x10 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ - msi-parent = <&its>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 7>; - interrupt-map = <0000 0 0 1 &gic 0 0 0 109 4>, - <0000 0 0 2 &gic 0 0 0 110 4>, - <0000 0 0 3 &gic 0 0 0 111 4>, - <0000 0 0 4 &gic 0 0 0 112 4>; - }; + cluster1_l2: l2-cache1 { + compatible = "cache"; + }; - pcie@3500000 { - compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", - "snps,dw-pcie"; - reg = <0x00 0x03500000 0x0 0x00100000 /* controller registers */ - 0x12 0x00000000 0x0 0x00002000>; /* configuration space */ - reg-names = "regs", "config"; - interrupts = <0 113 0x4>; /* Level high type */ - interrupt-names = "intr"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - dma-coherent; - num-lanes = <4>; - bus-range = <0x0 0xff>; - ranges = <0x81000000 0x0 0x00000000 0x12 0x00010000 0x0 0x00010000 /* downstream I/O */ - 0x82000000 0x0 0x40000000 0x12 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ - msi-parent = <&its>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 7>; - interrupt-map = <0000 0 0 1 &gic 0 0 0 114 4>, - <0000 0 0 2 &gic 0 0 0 115 4>, - <0000 0 0 3 &gic 0 0 0 116 4>, - <0000 0 0 4 &gic 0 0 0 117 4>; - }; + cluster2_l2: l2-cache2 { + compatible = "cache"; + }; - pcie@3600000 { - compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", - "snps,dw-pcie"; - reg = <0x00 0x03600000 0x0 0x00100000 /* controller registers */ - 0x14 0x00000000 0x0 0x00002000>; /* configuration space */ - reg-names = "regs", "config"; - interrupts = <0 118 0x4>; /* Level high type */ - interrupt-names = "intr"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - dma-coherent; - num-lanes = <8>; - bus-range = <0x0 0xff>; - ranges = <0x81000000 0x0 0x00000000 0x14 0x00010000 0x0 0x00010000 /* downstream I/O */ - 0x82000000 0x0 0x40000000 0x14 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ - msi-parent = <&its>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 7>; - interrupt-map = <0000 0 0 1 &gic 0 0 0 119 4>, - <0000 0 0 2 &gic 0 0 0 120 4>, - <0000 0 0 3 &gic 0 0 0 121 4>, - <0000 0 0 4 &gic 0 0 0 122 4>; - }; + cluster3_l2: l2-cache3 { + compatible = "cache"; + }; +}; - pcie@3700000 { - compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", - "snps,dw-pcie"; - reg = <0x00 0x03700000 0x0 0x00100000 /* controller registers */ - 0x16 0x00000000 0x0 0x00002000>; /* configuration space */ - reg-names = "regs", "config"; - interrupts = <0 123 0x4>; /* Level high type */ - interrupt-names = "intr"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - dma-coherent; - num-lanes = <4>; - bus-range = <0x0 0xff>; - ranges = <0x81000000 0x0 0x00000000 0x16 0x00010000 0x0 0x00010000 /* downstream I/O */ - 0x82000000 0x0 0x40000000 0x16 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ - msi-parent = <&its>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 7>; - interrupt-map = <0000 0 0 1 &gic 0 0 0 124 4>, - <0000 0 0 2 &gic 0 0 0 125 4>, - <0000 0 0 3 &gic 0 0 0 126 4>, - <0000 0 0 4 &gic 0 0 0 127 4>; - }; +&pcie1 { + reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */ + 0x10 0x00000000 0x0 0x00002000>; /* configuration space */ - sata0: sata@3200000 { - status = "disabled"; - compatible = "fsl,ls2080a-ahci"; - reg = <0x0 0x3200000 0x0 0x10000>; - interrupts = <0 133 0x4>; /* Level high type */ - clocks = <&clockgen 4 3>; - dma-coherent; - }; + ranges = <0x81000000 0x0 0x00000000 0x10 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x10 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ +}; - sata1: sata@3210000 { - status = "disabled"; - compatible = "fsl,ls2080a-ahci"; - reg = <0x0 0x3210000 0x0 0x10000>; - interrupts = <0 136 0x4>; /* Level high type */ - clocks = <&clockgen 4 3>; - dma-coherent; - }; +&pcie2 { + reg = <0x00 0x03500000 0x0 0x00100000 /* controller registers */ + 0x12 0x00000000 0x0 0x00002000>; /* configuration space */ - usb0: usb3@3100000 { - status = "disabled"; - compatible = "snps,dwc3"; - reg = <0x0 0x3100000 0x0 0x10000>; - interrupts = <0 80 0x4>; /* Level high type */ - dr_mode = "host"; - snps,quirk-frame-length-adjustment = <0x20>; - snps,dis_rxdet_inp3_quirk; - }; + ranges = <0x81000000 0x0 0x00000000 0x12 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x12 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ +}; - usb1: usb3@3110000 { - status = "disabled"; - compatible = "snps,dwc3"; - reg = <0x0 0x3110000 0x0 0x10000>; - interrupts = <0 81 0x4>; /* Level high type */ - dr_mode = "host"; - snps,quirk-frame-length-adjustment = <0x20>; - snps,dis_rxdet_inp3_quirk; - }; +&pcie3 { + reg = <0x00 0x03600000 0x0 0x00100000 /* controller registers */ + 0x14 0x00000000 0x0 0x00002000>; /* configuration space */ - ccn@4000000 { - compatible = "arm,ccn-504"; - reg = <0x0 0x04000000 0x0 0x01000000>; - interrupts = <0 12 4>; - }; - }; + ranges = <0x81000000 0x0 0x00000000 0x14 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x14 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ +}; - ddr1: memory-controller@1080000 { - compatible = "fsl,qoriq-memory-controller"; - reg = <0x0 0x1080000 0x0 0x1000>; - interrupts = <0 17 0x4>; - little-endian; - }; +&pcie4 { + reg = <0x00 0x03700000 0x0 0x00100000 /* controller registers */ + 0x16 0x00000000 0x0 0x00002000>; /* configuration space */ - ddr2: memory-controller@1090000 { - compatible = "fsl,qoriq-memory-controller"; - reg = <0x0 0x1090000 0x0 0x1000>; - interrupts = <0 18 0x4>; - little-endian; - }; + ranges = <0x81000000 0x0 0x00000000 0x16 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0x82000000 0x0 0x40000000 0x16 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts new file mode 100644 index 000000000000..ebcd6ee4da0d --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts @@ -0,0 +1,64 @@ +/* + * Device Tree file for Freescale LS2088A QDS Board. + * + * Copyright (C) 2016-17, Freescale Semiconductor + * + * Abhimanyu Saini <abhimanyu.saini@nxp.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "fsl-ls2088a.dtsi" +#include "fsl-ls208xa-qds.dtsi" + +/ { + model = "Freescale Layerscape 2088A QDS Board"; + compatible = "fsl,ls2088a-qds", "fsl,ls2088a"; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts new file mode 100644 index 000000000000..5992dc130faa --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts @@ -0,0 +1,64 @@ +/* + * Device Tree file for Freescale LS2088A RDB Board. + * + * Copyright (C) 2016-17, Freescale Semiconductor + * + * Abhimanyu Saini <abhimanyu.saini@nxp.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "fsl-ls2088a.dtsi" +#include "fsl-ls208xa-rdb.dtsi" + +/ { + model = "Freescale Layerscape 2088A RDB Board"; + compatible = "fsl,ls2088a-rdb", "fsl,ls2088a"; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + }; + + chosen { + stdout-path = "serial1:115200n8"; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi new file mode 100644 index 000000000000..33ce404cf7e4 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi @@ -0,0 +1,165 @@ +/* + * Device Tree Include file for Freescale Layerscape-2088A family SoC. + * + * Copyright (C) 2016-17, Freescale Semiconductor + * + * Abhimanyu Saini <abhimanyu.saini@nxp.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "fsl-ls208xa.dtsi" + +&cpu { + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x0>; + clocks = <&clockgen 1 0>; + next-level-cache = <&cluster0_l2>; + #cooling-cells = <2>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x1>; + clocks = <&clockgen 1 0>; + next-level-cache = <&cluster0_l2>; + }; + + cpu2: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x100>; + clocks = <&clockgen 1 1>; + next-level-cache = <&cluster1_l2>; + #cooling-cells = <2>; + }; + + cpu3: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x101>; + clocks = <&clockgen 1 1>; + next-level-cache = <&cluster1_l2>; + }; + + cpu4: cpu@200 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x200>; + clocks = <&clockgen 1 2>; + next-level-cache = <&cluster2_l2>; + #cooling-cells = <2>; + }; + + cpu5: cpu@201 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x201>; + clocks = <&clockgen 1 2>; + next-level-cache = <&cluster2_l2>; + }; + + cpu6: cpu@300 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x300>; + clocks = <&clockgen 1 3>; + next-level-cache = <&cluster3_l2>; + #cooling-cells = <2>; + }; + + cpu7: cpu@301 { + device_type = "cpu"; + compatible = "arm,cortex-a72"; + reg = <0x301>; + clocks = <&clockgen 1 3>; + next-level-cache = <&cluster3_l2>; + }; + + cluster0_l2: l2-cache0 { + compatible = "cache"; + }; + + cluster1_l2: l2-cache1 { + compatible = "cache"; + }; + + cluster2_l2: l2-cache2 { + compatible = "cache"; + }; + + cluster3_l2: l2-cache3 { + compatible = "cache"; + }; +}; + +&pcie1 { + reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */ + 0x20 0x00000000 0x0 0x00002000>; /* configuration space */ + + ranges = <0x81000000 0x0 0x00000000 0x20 0x00010000 0x0 0x00010000 + 0x82000000 0x0 0x40000000 0x20 0x40000000 0x0 0x40000000>; +}; + +&pcie2 { + reg = <0x00 0x03500000 0x0 0x00100000 /* controller registers */ + 0x28 0x00000000 0x0 0x00002000>; /* configuration space */ + + ranges = <0x81000000 0x0 0x00000000 0x28 0x00010000 0x0 0x00010000 + 0x82000000 0x0 0x40000000 0x28 0x40000000 0x0 0x40000000>; +}; + +&pcie3 { + reg = <0x00 0x03600000 0x0 0x00100000 /* controller registers */ + 0x30 0x00000000 0x0 0x00002000>; /* configuration space */ + + ranges = <0x81000000 0x0 0x00000000 0x30 0x00010000 0x0 0x00010000 + 0x82000000 0x0 0x40000000 0x30 0x40000000 0x0 0x40000000>; +}; + +&pcie4 { + reg = <0x00 0x03700000 0x0 0x00100000 /* controller registers */ + 0x38 0x00000000 0x0 0x00002000>; /* configuration space */ + + ranges = <0x81000000 0x0 0x00000000 0x38 0x00010000 0x0 0x00010000 + 0x82000000 0x0 0x40000000 0x38 0x40000000 0x0 0x40000000>; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi new file mode 100644 index 000000000000..8b6204845973 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi @@ -0,0 +1,196 @@ +/* + * Device Tree file for Freescale LS2080A QDS Board. + * + * Copyright (C) 2016-17, Freescale Semiconductor + * + * Abhimanyu Saini <abhimanyu.saini@nxp.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +&esdhc { + status = "okay"; +}; + +&ifc { + status = "okay"; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0x0 0x0 0x5 0x80000000 0x08000000 + 0x2 0x0 0x5 0x30000000 0x00010000 + 0x3 0x0 0x5 0x20000000 0x00010000>; + + nor@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x8000000>; + bank-width = <2>; + device-width = <1>; + }; + + nand@2,0 { + compatible = "fsl,ifc-nand"; + reg = <0x2 0x0 0x10000>; + }; + + cpld@3,0 { + reg = <0x3 0x0 0x10000>; + compatible = "fsl,ls2080aqds-fpga", "fsl,fpga-qixis"; + }; +}; + +&i2c0 { + status = "okay"; + pca9547@77 { + compatible = "nxp,pca9547"; + reg = <0x77>; + #address-cells = <1>; + #size-cells = <0>; + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x00>; + rtc@68 { + compatible = "dallas,ds3232"; + reg = <0x68>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x02>; + + ina220@40 { + compatible = "ti,ina220"; + reg = <0x40>; + shunt-resistor = <500>; + }; + + ina220@41 { + compatible = "ti,ina220"; + reg = <0x41>; + shunt-resistor = <1000>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3>; + + adt7481@4c { + compatible = "adi,adt7461"; + reg = <0x4c>; + }; + }; + }; +}; + +&i2c1 { + status = "disabled"; +}; + +&i2c2 { + status = "disabled"; +}; + +&i2c3 { + status = "disabled"; +}; + +&dspi { + status = "okay"; + dflash0: n25q128a { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <3000000>; + reg = <0>; + }; + dflash1: sst25wf040b { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <3000000>; + reg = <1>; + }; + dflash2: en25s64 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <3000000>; + reg = <2>; + }; +}; + +&qspi { + status = "okay"; + flash0: s25fl256s1@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <20000000>; + reg = <0>; + }; + flash2: s25fl256s1@2 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <20000000>; + reg = <0>; + }; +}; + +&sata0 { + status = "okay"; +}; + +&sata1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi new file mode 100644 index 000000000000..3737587ffb33 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi @@ -0,0 +1,151 @@ +/* + * Device Tree file for Freescale LS2080A RDB Board. + * + * Copyright (C) 2016-17, Freescale Semiconductor + * + * Abhimanyu Saini <abhimanyu.saini@nxp.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +&esdhc { + status = "okay"; +}; + +&ifc { + status = "okay"; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0x0 0x0 0x5 0x80000000 0x08000000 + 0x2 0x0 0x5 0x30000000 0x00010000 + 0x3 0x0 0x5 0x20000000 0x00010000>; + + nor@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x8000000>; + bank-width = <2>; + device-width = <1>; + }; + + nand@2,0 { + compatible = "fsl,ifc-nand"; + reg = <0x2 0x0 0x10000>; + }; + + cpld@3,0 { + reg = <0x3 0x0 0x10000>; + compatible = "fsl,ls2080aqds-fpga", "fsl,fpga-qixis"; + }; + +}; + +&i2c0 { + status = "okay"; + pca9547@75 { + compatible = "nxp,pca9547"; + reg = <0x75>; + #address-cells = <1>; + #size-cells = <0>; + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x01>; + rtc@68 { + compatible = "dallas,ds3232"; + reg = <0x68>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3>; + + adt7481@4c { + compatible = "adi,adt7461"; + reg = <0x4c>; + }; + }; + }; +}; + +&i2c1 { + status = "disabled"; +}; + +&i2c2 { + status = "disabled"; +}; + +&i2c3 { + status = "disabled"; +}; + +&dspi { + status = "okay"; + dflash0: n25q512a { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <3000000>; + reg = <0>; + }; +}; + +&qspi { + status = "disabled"; +}; + +&sata0 { + status = "okay"; +}; + +&sata1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi new file mode 100644 index 000000000000..abb2fff7d162 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi @@ -0,0 +1,737 @@ +/* + * Device Tree Include file for Freescale Layerscape-2080A family SoC. + * + * Copyright (C) 2016-2017, Freescale Semiconductor + * + * Abhimanyu Saini <abhimanyu.saini@nxp.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/thermal/thermal.h> + +/ { + compatible = "fsl,ls2080a"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + cpu: cpus { + #address-cells = <1>; + #size-cells = <0>; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x00000000 0x80000000 0 0x80000000>; + /* DRAM space - 1, size : 2 GB DRAM */ + }; + + sysclk: sysclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + clock-output-names = "sysclk"; + }; + + gic: interrupt-controller@6000000 { + compatible = "arm,gic-v3"; + reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */ + <0x0 0x06100000 0 0x100000>, /* GICR (RD_base + SGI_base) */ + <0x0 0x0c0c0000 0 0x2000>, /* GICC */ + <0x0 0x0c0d0000 0 0x1000>, /* GICH */ + <0x0 0x0c0e0000 0 0x20000>; /* GICV */ + #interrupt-cells = <3>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + interrupt-controller; + interrupts = <1 9 0x4>; + + its: gic-its@6020000 { + compatible = "arm,gic-v3-its"; + msi-controller; + reg = <0x0 0x6020000 0 0x20000>; + }; + }; + + rstcr: syscon@1e60000 { + compatible = "fsl,ls2080a-rstcr", "syscon"; + reg = <0x0 0x1e60000 0x0 0x4>; + }; + + reboot { + compatible ="syscon-reboot"; + regmap = <&rstcr>; + offset = <0x0>; + mask = <0x2>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <1 13 4>, /* Physical Secure PPI, active-low */ + <1 14 4>, /* Physical Non-Secure PPI, active-low */ + <1 11 4>, /* Virtual PPI, active-low */ + <1 10 4>; /* Hypervisor PPI, active-low */ + fsl,erratum-a008585; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <1 7 0x8>; /* PMU PPI, Level low type */ + }; + + soc { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clockgen: clocking@1300000 { + compatible = "fsl,ls2080a-clockgen"; + reg = <0 0x1300000 0 0xa0000>; + #clock-cells = <2>; + clocks = <&sysclk>; + }; + + dcfg: dcfg@1e00000 { + compatible = "fsl,ls2080a-dcfg", "syscon"; + reg = <0x0 0x1e00000 0x0 0x10000>; + little-endian; + }; + + tmu: tmu@1f80000 { + compatible = "fsl,qoriq-tmu"; + reg = <0x0 0x1f80000 0x0 0x10000>; + interrupts = <0 23 0x4>; + fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>; + fsl,tmu-calibration = <0x00000000 0x00000026 + 0x00000001 0x0000002d + 0x00000002 0x00000032 + 0x00000003 0x00000039 + 0x00000004 0x0000003f + 0x00000005 0x00000046 + 0x00000006 0x0000004d + 0x00000007 0x00000054 + 0x00000008 0x0000005a + 0x00000009 0x00000061 + 0x0000000a 0x0000006a + 0x0000000b 0x00000071 + + 0x00010000 0x00000025 + 0x00010001 0x0000002c + 0x00010002 0x00000035 + 0x00010003 0x0000003d + 0x00010004 0x00000045 + 0x00010005 0x0000004e + 0x00010006 0x00000057 + 0x00010007 0x00000061 + 0x00010008 0x0000006b + 0x00010009 0x00000076 + + 0x00020000 0x00000029 + 0x00020001 0x00000033 + 0x00020002 0x0000003d + 0x00020003 0x00000049 + 0x00020004 0x00000056 + 0x00020005 0x00000061 + 0x00020006 0x0000006d + + 0x00030000 0x00000021 + 0x00030001 0x0000002a + 0x00030002 0x0000003c + 0x00030003 0x0000004e>; + little-endian; + #thermal-sensor-cells = <1>; + }; + + thermal-zones { + cpu_thermal: cpu-thermal { + polling-delay-passive = <1000>; + polling-delay = <5000>; + + thermal-sensors = <&tmu 4>; + + trips { + cpu_alert: cpu-alert { + temperature = <75000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu_crit: cpu-crit { + temperature = <85000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_alert>; + cooling-device = + <&cpu0 THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu_alert>; + cooling-device = + <&cpu2 THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>; + }; + map2 { + trip = <&cpu_alert>; + cooling-device = + <&cpu4 THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>; + }; + map3 { + trip = <&cpu_alert>; + cooling-device = + <&cpu6 THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>; + }; + }; + }; + }; + + serial0: serial@21c0500 { + compatible = "fsl,ns16550", "ns16550a"; + reg = <0x0 0x21c0500 0x0 0x100>; + clocks = <&clockgen 4 3>; + interrupts = <0 32 0x4>; /* Level high type */ + }; + + serial1: serial@21c0600 { + compatible = "fsl,ns16550", "ns16550a"; + reg = <0x0 0x21c0600 0x0 0x100>; + clocks = <&clockgen 4 3>; + interrupts = <0 32 0x4>; /* Level high type */ + }; + + cluster1_core0_watchdog: wdt@c000000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc000000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster1_core1_watchdog: wdt@c010000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc010000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster2_core0_watchdog: wdt@c100000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc100000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster2_core1_watchdog: wdt@c110000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc110000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster3_core0_watchdog: wdt@c200000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc200000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster3_core1_watchdog: wdt@c210000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc210000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster4_core0_watchdog: wdt@c300000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc300000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + cluster4_core1_watchdog: wdt@c310000 { + compatible = "arm,sp805-wdt", "arm,primecell"; + reg = <0x0 0xc310000 0x0 0x1000>; + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "apb_pclk", "wdog_clk"; + }; + + fsl_mc: fsl-mc@80c000000 { + compatible = "fsl,qoriq-mc"; + reg = <0x00000008 0x0c000000 0 0x40>, /* MC portal base */ + <0x00000000 0x08340000 0 0x40000>; /* MC control reg */ + msi-parent = <&its>; + #address-cells = <3>; + #size-cells = <1>; + + /* + * Region type 0x0 - MC portals + * Region type 0x1 - QBMAN portals + */ + ranges = <0x0 0x0 0x0 0x8 0x0c000000 0x4000000 + 0x1 0x0 0x0 0x8 0x18000000 0x8000000>; + + /* + * Define the maximum number of MACs present on the SoC. + */ + dpmacs { + #address-cells = <1>; + #size-cells = <0>; + + dpmac1: dpmac@1 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x1>; + }; + + dpmac2: dpmac@2 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x2>; + }; + + dpmac3: dpmac@3 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x3>; + }; + + dpmac4: dpmac@4 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x4>; + }; + + dpmac5: dpmac@5 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x5>; + }; + + dpmac6: dpmac@6 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x6>; + }; + + dpmac7: dpmac@7 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x7>; + }; + + dpmac8: dpmac@8 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x8>; + }; + + dpmac9: dpmac@9 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x9>; + }; + + dpmac10: dpmac@a { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0xa>; + }; + + dpmac11: dpmac@b { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0xb>; + }; + + dpmac12: dpmac@c { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0xc>; + }; + + dpmac13: dpmac@d { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0xd>; + }; + + dpmac14: dpmac@e { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0xe>; + }; + + dpmac15: dpmac@f { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0xf>; + }; + + dpmac16: dpmac@10 { + compatible = "fsl,qoriq-mc-dpmac"; + reg = <0x10>; + }; + }; + }; + + smmu: iommu@5000000 { + compatible = "arm,mmu-500"; + reg = <0 0x5000000 0 0x800000>; + #global-interrupts = <12>; + interrupts = <0 13 4>, /* global secure fault */ + <0 14 4>, /* combined secure interrupt */ + <0 15 4>, /* global non-secure fault */ + <0 16 4>, /* combined non-secure interrupt */ + /* performance counter interrupts 0-7 */ + <0 211 4>, <0 212 4>, + <0 213 4>, <0 214 4>, + <0 215 4>, <0 216 4>, + <0 217 4>, <0 218 4>, + /* per context interrupt, 64 interrupts */ + <0 146 4>, <0 147 4>, + <0 148 4>, <0 149 4>, + <0 150 4>, <0 151 4>, + <0 152 4>, <0 153 4>, + <0 154 4>, <0 155 4>, + <0 156 4>, <0 157 4>, + <0 158 4>, <0 159 4>, + <0 160 4>, <0 161 4>, + <0 162 4>, <0 163 4>, + <0 164 4>, <0 165 4>, + <0 166 4>, <0 167 4>, + <0 168 4>, <0 169 4>, + <0 170 4>, <0 171 4>, + <0 172 4>, <0 173 4>, + <0 174 4>, <0 175 4>, + <0 176 4>, <0 177 4>, + <0 178 4>, <0 179 4>, + <0 180 4>, <0 181 4>, + <0 182 4>, <0 183 4>, + <0 184 4>, <0 185 4>, + <0 186 4>, <0 187 4>, + <0 188 4>, <0 189 4>, + <0 190 4>, <0 191 4>, + <0 192 4>, <0 193 4>, + <0 194 4>, <0 195 4>, + <0 196 4>, <0 197 4>, + <0 198 4>, <0 199 4>, + <0 200 4>, <0 201 4>, + <0 202 4>, <0 203 4>, + <0 204 4>, <0 205 4>, + <0 206 4>, <0 207 4>, + <0 208 4>, <0 209 4>; + mmu-masters = <&fsl_mc 0x300 0>; + }; + + dspi: dspi@2100000 { + status = "disabled"; + compatible = "fsl,ls2080a-dspi", "fsl,ls2085a-dspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2100000 0x0 0x10000>; + interrupts = <0 26 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>; + clock-names = "dspi"; + spi-num-chipselects = <5>; + bus-num = <0>; + }; + + esdhc: esdhc@2140000 { + status = "disabled"; + compatible = "fsl,ls2080a-esdhc", "fsl,esdhc"; + reg = <0x0 0x2140000 0x0 0x10000>; + interrupts = <0 28 0x4>; /* Level high type */ + clock-frequency = <0>; /* Updated by bootloader */ + voltage-ranges = <1800 1800 3300 3300>; + sdhci,auto-cmd12; + little-endian; + bus-width = <4>; + }; + + gpio0: gpio@2300000 { + compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2300000 0x0 0x10000>; + interrupts = <0 36 0x4>; /* Level high type */ + gpio-controller; + little-endian; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio@2310000 { + compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2310000 0x0 0x10000>; + interrupts = <0 36 0x4>; /* Level high type */ + gpio-controller; + little-endian; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio@2320000 { + compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2320000 0x0 0x10000>; + interrupts = <0 37 0x4>; /* Level high type */ + gpio-controller; + little-endian; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio@2330000 { + compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio"; + reg = <0x0 0x2330000 0x0 0x10000>; + interrupts = <0 37 0x4>; /* Level high type */ + gpio-controller; + little-endian; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + i2c0: i2c@2000000 { + status = "disabled"; + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2000000 0x0 0x10000>; + interrupts = <0 34 0x4>; /* Level high type */ + clock-names = "i2c"; + clocks = <&clockgen 4 3>; + }; + + i2c1: i2c@2010000 { + status = "disabled"; + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2010000 0x0 0x10000>; + interrupts = <0 34 0x4>; /* Level high type */ + clock-names = "i2c"; + clocks = <&clockgen 4 3>; + }; + + i2c2: i2c@2020000 { + status = "disabled"; + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2020000 0x0 0x10000>; + interrupts = <0 35 0x4>; /* Level high type */ + clock-names = "i2c"; + clocks = <&clockgen 4 3>; + }; + + i2c3: i2c@2030000 { + status = "disabled"; + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2030000 0x0 0x10000>; + interrupts = <0 35 0x4>; /* Level high type */ + clock-names = "i2c"; + clocks = <&clockgen 4 3>; + }; + + ifc: ifc@2240000 { + compatible = "fsl,ifc", "simple-bus"; + reg = <0x0 0x2240000 0x0 0x20000>; + interrupts = <0 21 0x4>; /* Level high type */ + little-endian; + #address-cells = <2>; + #size-cells = <1>; + + ranges = <0 0 0x5 0x80000000 0x08000000 + 2 0 0x5 0x30000000 0x00010000 + 3 0 0x5 0x20000000 0x00010000>; + }; + + qspi: quadspi@20c0000 { + status = "disabled"; + compatible = "fsl,ls2080a-qspi", "fsl,ls1021a-qspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x20c0000 0x0 0x10000>, + <0x0 0x20000000 0x0 0x10000000>; + reg-names = "QuadSPI", "QuadSPI-memory"; + interrupts = <0 25 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clock-names = "qspi_en", "qspi"; + }; + + pcie1: pcie@3400000 { + compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", + "snps,dw-pcie"; + reg-names = "regs", "config"; + interrupts = <0 108 0x4>; /* Level high type */ + interrupt-names = "intr"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + dma-coherent; + num-lanes = <4>; + bus-range = <0x0 0xff>; + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 0 109 4>, + <0000 0 0 2 &gic 0 0 0 110 4>, + <0000 0 0 3 &gic 0 0 0 111 4>, + <0000 0 0 4 &gic 0 0 0 112 4>; + }; + + pcie2: pcie@3500000 { + compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", + "snps,dw-pcie"; + reg-names = "regs", "config"; + interrupts = <0 113 0x4>; /* Level high type */ + interrupt-names = "intr"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + dma-coherent; + num-lanes = <4>; + bus-range = <0x0 0xff>; + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 0 114 4>, + <0000 0 0 2 &gic 0 0 0 115 4>, + <0000 0 0 3 &gic 0 0 0 116 4>, + <0000 0 0 4 &gic 0 0 0 117 4>; + }; + + pcie3: pcie@3600000 { + compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", + "snps,dw-pcie"; + reg-names = "regs", "config"; + interrupts = <0 118 0x4>; /* Level high type */ + interrupt-names = "intr"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + dma-coherent; + num-lanes = <8>; + bus-range = <0x0 0xff>; + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 0 119 4>, + <0000 0 0 2 &gic 0 0 0 120 4>, + <0000 0 0 3 &gic 0 0 0 121 4>, + <0000 0 0 4 &gic 0 0 0 122 4>; + }; + + pcie4: pcie@3700000 { + compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", + "snps,dw-pcie"; + reg-names = "regs", "config"; + interrupts = <0 123 0x4>; /* Level high type */ + interrupt-names = "intr"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + dma-coherent; + num-lanes = <4>; + bus-range = <0x0 0xff>; + msi-parent = <&its>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic 0 0 0 124 4>, + <0000 0 0 2 &gic 0 0 0 125 4>, + <0000 0 0 3 &gic 0 0 0 126 4>, + <0000 0 0 4 &gic 0 0 0 127 4>; + }; + + sata0: sata@3200000 { + status = "disabled"; + compatible = "fsl,ls2080a-ahci"; + reg = <0x0 0x3200000 0x0 0x10000>; + interrupts = <0 133 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>; + dma-coherent; + }; + + sata1: sata@3210000 { + status = "disabled"; + compatible = "fsl,ls2080a-ahci"; + reg = <0x0 0x3210000 0x0 0x10000>; + interrupts = <0 136 0x4>; /* Level high type */ + clocks = <&clockgen 4 3>; + dma-coherent; + }; + + usb0: usb3@3100000 { + status = "disabled"; + compatible = "snps,dwc3"; + reg = <0x0 0x3100000 0x0 0x10000>; + interrupts = <0 80 0x4>; /* Level high type */ + dr_mode = "host"; + snps,quirk-frame-length-adjustment = <0x20>; + snps,dis_rxdet_inp3_quirk; + }; + + usb1: usb3@3110000 { + status = "disabled"; + compatible = "snps,dwc3"; + reg = <0x0 0x3110000 0x0 0x10000>; + interrupts = <0 81 0x4>; /* Level high type */ + dr_mode = "host"; + snps,quirk-frame-length-adjustment = <0x20>; + snps,dis_rxdet_inp3_quirk; + }; + + ccn@4000000 { + compatible = "arm,ccn-504"; + reg = <0x0 0x04000000 0x0 0x01000000>; + interrupts = <0 12 4>; + }; + }; + + ddr1: memory-controller@1080000 { + compatible = "fsl,qoriq-memory-controller"; + reg = <0x0 0x1080000 0x0 0x1000>; + interrupts = <0 17 0x4>; + little-endian; + }; + + ddr2: memory-controller@1090000 { + compatible = "fsl,qoriq-memory-controller"; + reg = <0x0 0x1090000 0x0 0x1000>; + interrupts = <0 18 0x4>; + little-endian; + }; +}; diff --git a/arch/arm64/boot/dts/hisilicon/Makefile b/arch/arm64/boot/dts/hisilicon/Makefile index c3a6c1943038..8960ecafd37d 100644 --- a/arch/arm64/boot/dts/hisilicon/Makefile +++ b/arch/arm64/boot/dts/hisilicon/Makefile @@ -1,4 +1,5 @@ dtb-$(CONFIG_ARCH_HISI) += hi3660-hikey960.dtb +dtb-$(CONFIG_ARCH_HISI) += hi3798cv200-poplar.dtb dtb-$(CONFIG_ARCH_HISI) += hi6220-hikey.dtb dtb-$(CONFIG_ARCH_HISI) += hip05-d02.dtb dtb-$(CONFIG_ARCH_HISI) += hip06-d03.dtb diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts index ff37f0a0aa93..186251ffc6b2 100644 --- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts +++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts @@ -8,6 +8,7 @@ /dts-v1/; #include "hi3660.dtsi" +#include "hikey960-pinctrl.dtsi" / { model = "HiKey960"; diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts new file mode 100644 index 000000000000..b9142871d6fe --- /dev/null +++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts @@ -0,0 +1,162 @@ +/* + * DTS File for HiSilicon Poplar Development Board + * + * Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd. + * + * Released under the GPLv2 only. + * SPDX-License-Identifier: GPL-2.0 + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include "hi3798cv200.dtsi" + +/ { + model = "HiSilicon Poplar Development Board"; + compatible = "hisilicon,hi3798cv200-poplar", "hisilicon,hi3798cv200"; + + aliases { + serial0 = &uart0; + serial2 = &uart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + leds { + compatible = "gpio-leds"; + + user-led0 { + label = "USER-LED0"; + gpios = <&gpio6 3 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + user-led1 { + label = "USER-LED1"; + gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + user-led2 { + label = "USER-LED2"; + gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; + linux,default-trigger = "none"; + default-state = "off"; + }; + + user-led3 { + label = "USER-LED3"; + gpios = <&gpio10 6 GPIO_ACTIVE_LOW>; + linux,default-trigger = "cpu0"; + default-state = "off"; + }; + }; +}; + +&gmac1 { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + phy-handle = <ð_phy1>; + phy-mode = "rgmii"; + hisilicon,phy-reset-delays-us = <10000 10000 30000>; + + eth_phy1: phy@3 { + reg = <3>; + }; +}; + +&gpio1 { + status = "okay"; + gpio-line-names = "LS-GPIO-E", "", + "", "", + "", "LS-GPIO-F", + "", "LS-GPIO-J"; +}; + +&gpio2 { + status = "okay"; + gpio-line-names = "LS-GPIO-H", "LS-GPIO-I", + "LS-GPIO-L", "LS-GPIO-G", + "LS-GPIO-K", "", + "", ""; +}; + +&gpio3 { + status = "okay"; + gpio-line-names = "", "", + "", "", + "LS-GPIO-C", "", + "", "LS-GPIO-B"; +}; + +&gpio4 { + status = "okay"; + gpio-line-names = "", "", + "", "", + "", "LS-GPIO-D", + "", ""; +}; + +&gpio5 { + status = "okay"; + gpio-line-names = "", "USER-LED-1", + "USER-LED-2", "", + "", "LS-GPIO-A", + "", ""; +}; + +&gpio6 { + status = "okay"; + gpio-line-names = "", "", + "", "USER-LED-0", + "", "", + "", ""; +}; + +&gpio10 { + status = "okay"; + gpio-line-names = "", "", + "", "", + "", "", + "USER-LED-3", ""; +}; + +&i2c0 { + status = "okay"; + label = "LS-I2C0"; +}; + +&i2c2 { + status = "okay"; + label = "LS-I2C1"; +}; + +&ir { + status = "okay"; +}; + +&spi0 { + status = "okay"; + label = "LS-SPI0"; +}; + +&uart0 { + status = "okay"; +}; + +&uart2 { + status = "okay"; + label = "LS-UART0"; +}; +/* No optional LS-UART1 on Low Speed Expansion Connector. */ diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi new file mode 100644 index 000000000000..75865f8a862a --- /dev/null +++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi @@ -0,0 +1,411 @@ +/* + * DTS File for HiSilicon Hi3798cv200 SoC. + * + * Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd. + * + * Released under the GPLv2 only. + * SPDX-License-Identifier: GPL-2.0 + */ + +#include <dt-bindings/clock/histb-clock.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/reset/ti-syscon.h> + +/ { + compatible = "hisilicon,hi3798cv200"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu@0 { + compatible = "arm,cortex-a53"; + device_type = "cpu"; + reg = <0x0 0x0>; + enable-method = "psci"; + }; + + cpu@1 { + compatible = "arm,cortex-a53"; + device_type = "cpu"; + reg = <0x0 0x1>; + enable-method = "psci"; + }; + + cpu@2 { + compatible = "arm,cortex-a53"; + device_type = "cpu"; + reg = <0x0 0x2>; + enable-method = "psci"; + }; + + cpu@3 { + compatible = "arm,cortex-a53"; + device_type = "cpu"; + reg = <0x0 0x3>; + enable-method = "psci"; + }; + }; + + gic: interrupt-controller@f1001000 { + compatible = "arm,gic-400"; + reg = <0x0 0xf1001000 0x0 0x1000>, /* GICD */ + <0x0 0xf1002000 0x0 0x100>; /* GICC */ + #address-cells = <0>; + #interrupt-cells = <3>; + interrupt-controller; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_LOW)>; + }; + + soc: soc@f0000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0xf0000000 0x10000000>; + + crg: clock-reset-controller@8a22000 { + compatible = "hisilicon,hi3798cv200-crg", "syscon", "simple-mfd"; + reg = <0x8a22000 0x1000>; + #clock-cells = <1>; + #reset-cells = <2>; + + gmacphyrst: reset-controller { + compatible = "ti,syscon-reset"; + #reset-cells = <1>; + ti,reset-bits = + <0xcc 12 0xcc 12 0 0 (ASSERT_CLEAR | + DEASSERT_SET|STATUS_NONE)>, + <0xcc 13 0xcc 13 0 0 (ASSERT_CLEAR | + DEASSERT_SET|STATUS_NONE)>; + }; + }; + + sysctrl: system-controller@8000000 { + compatible = "hisilicon,hi3798cv200-sysctrl", "syscon"; + reg = <0x8000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <2>; + }; + + uart0: serial@8b00000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x8b00000 0x1000>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sysctrl HISTB_UART0_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + uart2: serial@8b02000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x8b02000 0x1000>; + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg HISTB_UART2_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + i2c0: i2c@8b10000 { + compatible = "hisilicon,hix5hd2-i2c"; + reg = <0x8b10000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <400000>; + clocks = <&crg HISTB_I2C0_CLK>; + status = "disabled"; + }; + + i2c1: i2c@8b11000 { + compatible = "hisilicon,hix5hd2-i2c"; + reg = <0x8b11000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <400000>; + clocks = <&crg HISTB_I2C1_CLK>; + status = "disabled"; + }; + + i2c2: i2c@8b12000 { + compatible = "hisilicon,hix5hd2-i2c"; + reg = <0x8b12000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <400000>; + clocks = <&crg HISTB_I2C2_CLK>; + status = "disabled"; + }; + + i2c3: i2c@8b13000 { + compatible = "hisilicon,hix5hd2-i2c"; + reg = <0x8b13000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <400000>; + clocks = <&crg HISTB_I2C3_CLK>; + status = "disabled"; + }; + + i2c4: i2c@8b14000 { + compatible = "hisilicon,hix5hd2-i2c"; + reg = <0x8b14000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <400000>; + clocks = <&crg HISTB_I2C4_CLK>; + status = "disabled"; + }; + + spi0: spi@8b1a000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x8b1a000 0x1000>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + num-cs = <1>; + cs-gpios = <&gpio7 1 0>; + clocks = <&crg HISTB_SPI0_CLK>; + clock-names = "apb_pclk"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + emmc: mmc@9830000 { + compatible = "snps,dw-mshc"; + reg = <0x9830000 0x10000>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg HISTB_MMC_CIU_CLK>, + <&crg HISTB_MMC_BIU_CLK>; + clock-names = "ciu", "biu"; + }; + + gpio0: gpio@8b20000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x8b20000 0x1000>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg HISTB_APB_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gpio1: gpio@8b21000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x8b21000 0x1000>; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg HISTB_APB_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gpio2: gpio@8b22000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x8b22000 0x1000>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg HISTB_APB_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gpio3: gpio@8b23000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x8b23000 0x1000>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg HISTB_APB_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gpio4: gpio@8b24000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x8b24000 0x1000>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg HISTB_APB_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gpio5: gpio@8004000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x8004000 0x1000>; + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg HISTB_APB_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gpio6: gpio@8b26000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x8b26000 0x1000>; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg HISTB_APB_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gpio7: gpio@8b27000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x8b27000 0x1000>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg HISTB_APB_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gpio8: gpio@8b28000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x8b28000 0x1000>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg HISTB_APB_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gpio9: gpio@8b29000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x8b29000 0x1000>; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg HISTB_APB_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gpio10: gpio@8b2a000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x8b2a000 0x1000>; + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg HISTB_APB_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gpio11: gpio@8b2b000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x8b2b000 0x1000>; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg HISTB_APB_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gpio12: gpio@8b2c000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0x8b2c000 0x1000>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg HISTB_APB_CLK>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gmac0: ethernet@9840000 { + compatible = "hisilicon,hi3798cv200-gmac", "hisilicon,hisi-gmac-v2"; + reg = <0x9840000 0x1000>, + <0x984300c 0x4>; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg HISTB_ETH0_MAC_CLK>, + <&crg HISTB_ETH0_MACIF_CLK>; + clock-names = "mac_core", "mac_ifc"; + resets = <&crg 0xcc 8>, + <&crg 0xcc 10>, + <&gmacphyrst 0>; + reset-names = "mac_core", "mac_ifc", "phy"; + status = "disabled"; + }; + + gmac1: ethernet@9841000 { + compatible = "hisilicon,hi3798cv200-gmac", "hisilicon,hisi-gmac-v2"; + reg = <0x9841000 0x1000>, + <0x9843010 0x4>; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg HISTB_ETH1_MAC_CLK>, + <&crg HISTB_ETH1_MACIF_CLK>; + clock-names = "mac_core", "mac_ifc"; + resets = <&crg 0xcc 9>, + <&crg 0xcc 11>, + <&gmacphyrst 1>; + reset-names = "mac_core", "mac_ifc", "phy"; + status = "disabled"; + }; + + ir: ir@8001000 { + compatible = "hisilicon,hix5hd2-ir"; + reg = <0x8001000 0x1000>; + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sysctrl HISTB_IR_CLK>; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts index dba3c131c62c..75bce2d0b1a8 100644 --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts @@ -98,6 +98,11 @@ assigned-clocks = <&sys_ctrl HI6220_UART1_SRC>; assigned-clock-rates = <150000000>; status = "ok"; + + bluetooth { + compatible = "ti,wl1835-st"; + enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + }; }; uart2: uart@f7112000 { @@ -406,6 +411,13 @@ }; }; }; + + firmware { + optee { + compatible = "linaro,optee-tz"; + method = "smc"; + }; + }; }; &uart2 { diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi index 470461ddd427..1e5129b19280 100644 --- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi @@ -774,6 +774,7 @@ clocks = <&sys_ctrl 2>, <&sys_ctrl 1>; clock-names = "ciu", "biu"; resets = <&sys_ctrl PERIPH_RSTDIS0_MMC0>; + reset-names = "reset"; bus-width = <0x8>; vmmc-supply = <&ldo19>; pinctrl-names = "default"; @@ -797,6 +798,7 @@ clocks = <&sys_ctrl 4>, <&sys_ctrl 3>; clock-names = "ciu", "biu"; resets = <&sys_ctrl PERIPH_RSTDIS0_MMC1>; + reset-names = "reset"; vqmmc-supply = <&ldo7>; vmmc-supply = <&ldo10>; bus-width = <0x4>; @@ -815,6 +817,7 @@ clocks = <&sys_ctrl HI6220_MMC2_CIUCLK>, <&sys_ctrl HI6220_MMC2_CLK>; clock-names = "ciu", "biu"; resets = <&sys_ctrl PERIPH_RSTDIS0_MMC2>; + reset-names = "reset"; bus-width = <0x4>; broken-cd; pinctrl-names = "default", "idle"; diff --git a/arch/arm64/boot/dts/hisilicon/hikey960-pinctrl.dtsi b/arch/arm64/boot/dts/hisilicon/hikey960-pinctrl.dtsi new file mode 100644 index 000000000000..719c4bc937a4 --- /dev/null +++ b/arch/arm64/boot/dts/hisilicon/hikey960-pinctrl.dtsi @@ -0,0 +1,407 @@ +/* + * pinctrl dts fils for Hislicon HiKey960 development board + * + */ + +#include <dt-bindings/pinctrl/hisi.h> + +/ { + soc { + /* [IOMG_000, IOMG_123] */ + range: gpio-range { + #pinctrl-single,gpio-range-cells = <3>; + }; + + pmx0: pinmux@e896c000 { + compatible = "pinctrl-single"; + reg = <0x0 0xe896c000 0x0 0x1f0>; + #pinctrl-cells = <1>; + #gpio-range-cells = <0x3>; + pinctrl-single,register-width = <0x20>; + pinctrl-single,function-mask = <0x7>; + /* pin base, nr pins & gpio function */ + pinctrl-single,gpio-range = < + &range 0 7 0 + &range 8 116 0>; + + isp0_pmx_func: isp0_pmx_func { + pinctrl-single,pins = < + 0x058 MUX_M1 /* ISP_CLK0 */ + 0x064 MUX_M1 /* ISP_SCL0 */ + 0x068 MUX_M1 /* ISP_SDA0 */ + >; + }; + + isp1_pmx_func: isp1_pmx_func { + pinctrl-single,pins = < + 0x05c MUX_M1 /* ISP_CLK1 */ + 0x06c MUX_M1 /* ISP_SCL1 */ + 0x070 MUX_M1 /* ISP_SDA1 */ + >; + }; + + i2c3_pmx_func: i2c3_pmx_func { + pinctrl-single,pins = < + 0x02c MUX_M1 /* I2C3_SCL */ + 0x030 MUX_M1 /* I2C3_SDA */ + >; + }; + + i2c4_pmx_func: i2c4_pmx_func { + pinctrl-single,pins = < + 0x090 MUX_M1 /* I2C4_SCL */ + 0x094 MUX_M1 /* I2C4_SDA */ + >; + }; + + pcie_perstn_pmx_func: pcie_perstn_pmx_func { + pinctrl-single,pins = < + 0x15c MUX_M1 /* PCIE_PERST_N */ + >; + }; + + usbhub5734_pmx_func: usbhub5734_pmx_func { + pinctrl-single,pins = < + 0x11c MUX_M0 /* GPIO_073 */ + 0x120 MUX_M0 /* GPIO_074 */ + >; + }; + + spi1_pmx_func: spi1_pmx_func { + pinctrl-single,pins = < + 0x034 MUX_M1 /* SPI1_CLK */ + 0x038 MUX_M1 /* SPI1_DI */ + 0x03c MUX_M1 /* SPI1_DO */ + 0x040 MUX_M1 /* SPI1_CS_N */ + >; + }; + + uart0_pmx_func: uart0_pmx_func { + pinctrl-single,pins = < + 0x0cc MUX_M2 /* UART0_RXD */ + 0x0d0 MUX_M2 /* UART0_TXD */ + 0x0d4 MUX_M2 /* UART0_RXD_M */ + 0x0d8 MUX_M2 /* UART0_TXD_M */ + >; + }; + + uart1_pmx_func: uart1_pmx_func { + pinctrl-single,pins = < + 0x0b0 MUX_M2 /* UART1_CTS_N */ + 0x0b4 MUX_M2 /* UART1_RTS_N */ + 0x0a8 MUX_M2 /* UART1_RXD */ + 0x0ac MUX_M2 /* UART1_TXD */ + >; + }; + + uart2_pmx_func: uart2_pmx_func { + pinctrl-single,pins = < + 0x0bc MUX_M2 /* UART2_CTS_N */ + 0x0c0 MUX_M2 /* UART2_RTS_N */ + 0x0c8 MUX_M2 /* UART2_RXD */ + 0x0c4 MUX_M2 /* UART2_TXD */ + >; + }; + + uart3_pmx_func: uart3_pmx_func { + pinctrl-single,pins = < + 0x0dc MUX_M1 /* UART3_CTS_N */ + 0x0e0 MUX_M1 /* UART3_RTS_N */ + 0x0e4 MUX_M1 /* UART3_RXD */ + 0x0e8 MUX_M1 /* UART3_TXD */ + >; + }; + + uart4_pmx_func: uart4_pmx_func { + pinctrl-single,pins = < + 0x0ec MUX_M1 /* UART4_CTS_N */ + 0x0f0 MUX_M1 /* UART4_RTS_N */ + 0x0f4 MUX_M1 /* UART4_RXD */ + 0x0f8 MUX_M1 /* UART4_TXD */ + >; + }; + + uart5_pmx_func: uart5_pmx_func { + pinctrl-single,pins = < + 0x0c4 MUX_M3 /* UART5_CTS_N */ + 0x0c8 MUX_M3 /* UART5_RTS_N */ + 0x0bc MUX_M3 /* UART5_RXD */ + 0x0c0 MUX_M3 /* UART5_TXD */ + >; + }; + + uart6_pmx_func: uart6_pmx_func { + pinctrl-single,pins = < + 0x0cc MUX_M1 /* UART6_CTS_N */ + 0x0d0 MUX_M1 /* UART6_RTS_N */ + 0x0d4 MUX_M1 /* UART6_RXD */ + 0x0d8 MUX_M1 /* UART6_TXD */ + >; + }; + }; + + /* [IOMG_MMC0_000, IOMG_MMC0_005] */ + pmx1: pinmux@ff37e000 { + compatible = "pinctrl-single"; + reg = <0x0 0xff37e000 0x0 0x18>; + #gpio-range-cells = <0x3>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <0x20>; + pinctrl-single,function-mask = <0x7>; + /* pin base, nr pins & gpio function */ + pinctrl-single,gpio-range = <&range 0 6 0>; + + sd_pmx_func: sd_pmx_func { + pinctrl-single,pins = < + 0x000 MUX_M1 /* SD_CLK */ + 0x004 MUX_M1 /* SD_CMD */ + 0x008 MUX_M1 /* SD_DATA0 */ + 0x00c MUX_M1 /* SD_DATA1 */ + 0x010 MUX_M1 /* SD_DATA2 */ + 0x014 MUX_M1 /* SD_DATA3 */ + >; + }; + }; + + /* [IOMG_FIX_000, IOMG_FIX_011] */ + pmx2: pinmux@ff3b6000 { + compatible = "pinctrl-single"; + reg = <0x0 0xff3b6000 0x0 0x30>; + #pinctrl-cells = <1>; + #gpio-range-cells = <0x3>; + pinctrl-single,register-width = <0x20>; + pinctrl-single,function-mask = <0x7>; + /* pin base, nr pins & gpio function */ + pinctrl-single,gpio-range = <&range 0 12 0>; + + spi3_pmx_func: spi3_pmx_func { + pinctrl-single,pins = < + 0x008 MUX_M1 /* SPI3_CLK */ + 0x00c MUX_M1 /* SPI3_DI */ + 0x010 MUX_M1 /* SPI3_DO */ + 0x014 MUX_M1 /* SPI3_CS0_N */ + >; + }; + }; + + /* [IOMG_MMC1_000, IOMG_MMC1_005] */ + pmx3: pinmux@ff3fd000 { + compatible = "pinctrl-single"; + reg = <0x0 0xff3fd000 0x0 0x18>; + #pinctrl-cells = <1>; + #gpio-range-cells = <0x3>; + pinctrl-single,register-width = <0x20>; + pinctrl-single,function-mask = <0x7>; + /* pin base, nr pins & gpio function */ + pinctrl-single,gpio-range = <&range 0 6 0>; + + sdio_pmx_func: sdio_pmx_func { + pinctrl-single,pins = < + 0x000 MUX_M1 /* SDIO_CLK */ + 0x004 MUX_M1 /* SDIO_CMD */ + 0x008 MUX_M1 /* SDIO_DATA0 */ + 0x00c MUX_M1 /* SDIO_DATA1 */ + 0x010 MUX_M1 /* SDIO_DATA2 */ + 0x014 MUX_M1 /* SDIO_DATA3 */ + >; + }; + }; + + /* [IOMG_AO_000, IOMG_AO_041] */ + pmx4: pinmux@fff11000 { + compatible = "pinctrl-single"; + reg = <0x0 0xfff11000 0x0 0xa8>; + #pinctrl-cells = <1>; + #gpio-range-cells = <0x3>; + pinctrl-single,register-width = <0x20>; + pinctrl-single,function-mask = <0x7>; + /* pin base in node, nr pins & gpio function */ + pinctrl-single,gpio-range = <&range 0 42 0>; + + i2s2_pmx_func: i2s2_pmx_func { + pinctrl-single,pins = < + 0x044 MUX_M1 /* I2S2_DI */ + 0x048 MUX_M1 /* I2S2_DO */ + 0x04c MUX_M1 /* I2S2_XCLK */ + 0x050 MUX_M1 /* I2S2_XFS */ + >; + }; + + slimbus_pmx_func: slimbus_pmx_func { + pinctrl-single,pins = < + 0x02c MUX_M1 /* SLIMBUS_CLK */ + 0x030 MUX_M1 /* SLIMBUS_DATA */ + >; + }; + + i2c0_pmx_func: i2c0_pmx_func { + pinctrl-single,pins = < + 0x014 MUX_M1 /* I2C0_SCL */ + 0x018 MUX_M1 /* I2C0_SDA */ + >; + }; + + i2c1_pmx_func: i2c1_pmx_func { + pinctrl-single,pins = < + 0x01c MUX_M1 /* I2C1_SCL */ + 0x020 MUX_M1 /* I2C1_SDA */ + >; + }; + + i2c2_pmx_func: i2c2_pmx_func { + pinctrl-single,pins = < + 0x024 MUX_M1 /* I2C2_SCL */ + 0x028 MUX_M1 /* I2C2_SDA */ + >; + }; + + i2c7_pmx_func: i2c7_pmx_func { + pinctrl-single,pins = < + 0x024 MUX_M3 /* I2C7_SCL */ + 0x028 MUX_M3 /* I2C7_SDA */ + >; + }; + + spi2_pmx_func: spi2_pmx_func { + pinctrl-single,pins = < + 0x08c MUX_M1 /* SPI2_CLK */ + 0x090 MUX_M1 /* SPI2_DI */ + 0x094 MUX_M1 /* SPI2_DO */ + 0x098 MUX_M1 /* SPI2_CS0_N */ + >; + }; + + spi4_pmx_func: spi4_pmx_func { + pinctrl-single,pins = < + 0x08c MUX_M4 /* SPI4_CLK */ + 0x090 MUX_M4 /* SPI4_DI */ + 0x094 MUX_M4 /* SPI4_DO */ + 0x098 MUX_M4 /* SPI4_CS0_N */ + >; + }; + + i2s0_pmx_func: i2s0_pmx_func { + pinctrl-single,pins = < + 0x034 MUX_M1 /* I2S0_DI */ + 0x038 MUX_M1 /* I2S0_DO */ + 0x03c MUX_M1 /* I2S0_XCLK */ + 0x040 MUX_M1 /* I2S0_XFS */ + >; + }; + }; + + pmx5: pinmux@ff3fd800 { + compatible = "pinconf-single"; + reg = <0x0 0xff3fd800 0x0 0x18>; + #pinctrl-cells = <1>; + #address-cells = <1>; + #size-cells = <1>; + pinctrl-single,register-width = <32>; + + sdio_clk_cfg_func: sdio_clk_cfg_func { + pinctrl-single,pins = < + 0x000 0x0 /* SDIO_CLK */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE6_32MA + DRIVE6_MASK + >; + }; + + sdio_cfg_func: sdio_cfg_func { + pinctrl-single,pins = < + 0x004 0x0 /* SDIO_CMD */ + 0x008 0x0 /* SDIO_DATA0 */ + 0x00c 0x0 /* SDIO_DATA1 */ + 0x010 0x0 /* SDIO_DATA2 */ + 0x014 0x0 /* SDIO_DATA3 */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_UP + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE6_19MA + DRIVE6_MASK + >; + }; + }; + + pmx6: pinmux@ff37e800 { + compatible = "pinconf-single"; + reg = <0x0 0xff37e800 0x0 0x18>; + #pinctrl-cells = <1>; + #address-cells = <1>; + #size-cells = <1>; + pinctrl-single,register-width = <32>; + + sd_clk_cfg_func: sd_clk_cfg_func { + pinctrl-single,pins = < + 0x000 0x0 /* SD_CLK */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE6_32MA + DRIVE6_MASK + >; + }; + + sd_cfg_func: sd_cfg_func { + pinctrl-single,pins = < + 0x004 0x0 /* SD_CMD */ + 0x008 0x0 /* SD_DATA0 */ + 0x00c 0x0 /* SD_DATA1 */ + 0x010 0x0 /* SD_DATA2 */ + 0x014 0x0 /* SD_DATA3 */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_UP + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE6_19MA + DRIVE6_MASK + >; + }; + }; + }; +}; diff --git a/arch/arm64/boot/dts/hisilicon/hip07-d05.dts b/arch/arm64/boot/dts/hisilicon/hip07-d05.dts index e05844230583..f5d7f0889b41 100644 --- a/arch/arm64/boot/dts/hisilicon/hip07-d05.dts +++ b/arch/arm64/boot/dts/hisilicon/hip07-d05.dts @@ -64,3 +64,23 @@ &usb_ehci { status = "ok"; }; + +ð0 { + status = "ok"; +}; + +ð1 { + status = "ok"; +}; + +ð2 { + status = "ok"; +}; + +ð3 { + status = "ok"; +}; + +&sas1 { + status = "ok"; +}; diff --git a/arch/arm64/boot/dts/hisilicon/hip07.dtsi b/arch/arm64/boot/dts/hisilicon/hip07.dtsi index 5144eb1c179d..283d7b532e16 100644 --- a/arch/arm64/boot/dts/hisilicon/hip07.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hip07.dtsi @@ -1014,6 +1014,34 @@ compatible = "hisilicon,mbigen-v2"; reg = <0x0 0xa0080000 0x0 0x10000>; + mbigen_pcie2_a: intc_pcie2_a { + msi-parent = <&p0_its_dsa_a 0x40087>; + interrupt-controller; + #interrupt-cells = <2>; + num-pins = <10>; + }; + + mbigen_sas1: intc_sas1 { + msi-parent = <&p0_its_dsa_a 0x40000>; + interrupt-controller; + #interrupt-cells = <2>; + num-pins = <128>; + }; + + mbigen_sas2: intc_sas2 { + msi-parent = <&p0_its_dsa_a 0x40040>; + interrupt-controller; + #interrupt-cells = <2>; + num-pins = <128>; + }; + + mbigen_smmu_pcie: intc_smmu_pcie { + msi-parent = <&p0_its_dsa_a 0x40b0c>; + interrupt-controller; + #interrupt-cells = <2>; + num-pins = <3>; + }; + mbigen_usb: intc_usb { msi-parent = <&p0_its_dsa_a 0x40080>; interrupt-controller; @@ -1022,6 +1050,39 @@ }; }; + p0_mbigen_dsa_a: interrupt-controller@c0080000 { + compatible = "hisilicon,mbigen-v2"; + reg = <0x0 0xc0080000 0x0 0x10000>; + + mbigen_dsaf0: intc_dsaf0 { + msi-parent = <&p0_its_dsa_a 0x40800>; + interrupt-controller; + #interrupt-cells = <2>; + num-pins = <409>; + }; + + mbigen_dsa_roce: intc-roce { + msi-parent = <&p0_its_dsa_a 0x40B1E>; + interrupt-controller; + #interrupt-cells = <2>; + num-pins = <34>; + }; + + mbigen_sas0: intc-sas0 { + msi-parent = <&p0_its_dsa_a 0x40900>; + interrupt-controller; + #interrupt-cells = <2>; + num-pins = <128>; + }; + + mbigen_smmu_dsa: intc_smmu_dsa { + msi-parent = <&p0_its_dsa_a 0x40b20>; + interrupt-controller; + #interrupt-cells = <2>; + num-pins = <3>; + }; + }; + soc { compatible = "simple-bus"; #address-cells = <2>; @@ -1055,5 +1116,423 @@ dma-coherent; status = "disabled"; }; + + peri_c_subctrl: sub_ctrl_c@60000000 { + compatible = "hisilicon,peri-subctrl","syscon"; + reg = <0 0x60000000 0x0 0x10000>; + }; + + dsa_subctrl: dsa_subctrl@c0000000 { + compatible = "hisilicon,dsa-subctrl", "syscon"; + reg = <0x0 0xc0000000 0x0 0x10000>; + }; + + pcie_subctl: pcie_subctl@a0000000 { + compatible = "hisilicon,pcie-sas-subctrl", "syscon"; + reg = <0x0 0xa0000000 0x0 0x10000>; + }; + + serdes_ctrl: sds_ctrl@c2200000 { + compatible = "syscon"; + reg = <0 0xc2200000 0x0 0x80000>; + }; + + mdio@603c0000 { + compatible = "hisilicon,hns-mdio"; + reg = <0x0 0x603c0000 0x0 0x1000>; + subctrl-vbase = <&peri_c_subctrl 0x338 0xa38 + 0x531c 0x5a1c>; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + + phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + }; + + dsaf0: dsa@c7000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "hisilicon,hns-dsaf-v2"; + mode = "6port-16rss"; + reg = <0x0 0xc5000000 0x0 0x890000 + 0x0 0xc7000000 0x0 0x600000>; + reg-names = "ppe-base", "dsaf-base"; + interrupt-parent = <&mbigen_dsaf0>; + subctrl-syscon = <&dsa_subctrl>; + reset-field-offset = <0>; + interrupts = + <576 1>, <577 1>, <578 1>, <579 1>, <580 1>, + <581 1>, <582 1>, <583 1>, <584 1>, <585 1>, + <586 1>, <587 1>, <588 1>, <589 1>, <590 1>, + <591 1>, <592 1>, <593 1>, <594 1>, <595 1>, + <596 1>, <597 1>, <598 1>, <599 1>, <600 1>, + <960 1>, <961 1>, <962 1>, <963 1>, <964 1>, + <965 1>, <966 1>, <967 1>, <968 1>, <969 1>, + <970 1>, <971 1>, <972 1>, <973 1>, <974 1>, + <975 1>, <976 1>, <977 1>, <978 1>, <979 1>, + <980 1>, <981 1>, <982 1>, <983 1>, <984 1>, + <985 1>, <986 1>, <987 1>, <988 1>, <989 1>, + <990 1>, <991 1>, <992 1>, <993 1>, <994 1>, + <995 1>, <996 1>, <997 1>, <998 1>, <999 1>, + <1000 1>, <1001 1>, <1002 1>, <1003 1>, <1004 1>, + <1005 1>, <1006 1>, <1007 1>, <1008 1>, <1009 1>, + <1010 1>, <1011 1>, <1012 1>, <1013 1>, <1014 1>, + <1015 1>, <1016 1>, <1017 1>, <1018 1>, <1019 1>, + <1020 1>, <1021 1>, <1022 1>, <1023 1>, <1024 1>, + <1025 1>, <1026 1>, <1027 1>, <1028 1>, <1029 1>, + <1030 1>, <1031 1>, <1032 1>, <1033 1>, <1034 1>, + <1035 1>, <1036 1>, <1037 1>, <1038 1>, <1039 1>, + <1040 1>, <1041 1>, <1042 1>, <1043 1>, <1044 1>, + <1045 1>, <1046 1>, <1047 1>, <1048 1>, <1049 1>, + <1050 1>, <1051 1>, <1052 1>, <1053 1>, <1054 1>, + <1055 1>, <1056 1>, <1057 1>, <1058 1>, <1059 1>, + <1060 1>, <1061 1>, <1062 1>, <1063 1>, <1064 1>, + <1065 1>, <1066 1>, <1067 1>, <1068 1>, <1069 1>, + <1070 1>, <1071 1>, <1072 1>, <1073 1>, <1074 1>, + <1075 1>, <1076 1>, <1077 1>, <1078 1>, <1079 1>, + <1080 1>, <1081 1>, <1082 1>, <1083 1>, <1084 1>, + <1085 1>, <1086 1>, <1087 1>, <1088 1>, <1089 1>, + <1090 1>, <1091 1>, <1092 1>, <1093 1>, <1094 1>, + <1095 1>, <1096 1>, <1097 1>, <1098 1>, <1099 1>, + <1100 1>, <1101 1>, <1102 1>, <1103 1>, <1104 1>, + <1105 1>, <1106 1>, <1107 1>, <1108 1>, <1109 1>, + <1110 1>, <1111 1>, <1112 1>, <1113 1>, <1114 1>, + <1115 1>, <1116 1>, <1117 1>, <1118 1>, <1119 1>, + <1120 1>, <1121 1>, <1122 1>, <1123 1>, <1124 1>, + <1125 1>, <1126 1>, <1127 1>, <1128 1>, <1129 1>, + <1130 1>, <1131 1>, <1132 1>, <1133 1>, <1134 1>, + <1135 1>, <1136 1>, <1137 1>, <1138 1>, <1139 1>, + <1140 1>, <1141 1>, <1142 1>, <1143 1>, <1144 1>, + <1145 1>, <1146 1>, <1147 1>, <1148 1>, <1149 1>, + <1150 1>, <1151 1>, <1152 1>, <1153 1>, <1154 1>, + <1155 1>, <1156 1>, <1157 1>, <1158 1>, <1159 1>, + <1160 1>, <1161 1>, <1162 1>, <1163 1>, <1164 1>, + <1165 1>, <1166 1>, <1167 1>, <1168 1>, <1169 1>, + <1170 1>, <1171 1>, <1172 1>, <1173 1>, <1174 1>, + <1175 1>, <1176 1>, <1177 1>, <1178 1>, <1179 1>, + <1180 1>, <1181 1>, <1182 1>, <1183 1>, <1184 1>, + <1185 1>, <1186 1>, <1187 1>, <1188 1>, <1189 1>, + <1190 1>, <1191 1>, <1192 1>, <1193 1>, <1194 1>, + <1195 1>, <1196 1>, <1197 1>, <1198 1>, <1199 1>, + <1200 1>, <1201 1>, <1202 1>, <1203 1>, <1204 1>, + <1205 1>, <1206 1>, <1207 1>, <1208 1>, <1209 1>, + <1210 1>, <1211 1>, <1212 1>, <1213 1>, <1214 1>, + <1215 1>, <1216 1>, <1217 1>, <1218 1>, <1219 1>, + <1220 1>, <1221 1>, <1222 1>, <1223 1>, <1224 1>, + <1225 1>, <1226 1>, <1227 1>, <1228 1>, <1229 1>, + <1230 1>, <1231 1>, <1232 1>, <1233 1>, <1234 1>, + <1235 1>, <1236 1>, <1237 1>, <1238 1>, <1239 1>, + <1240 1>, <1241 1>, <1242 1>, <1243 1>, <1244 1>, + <1245 1>, <1246 1>, <1247 1>, <1248 1>, <1249 1>, + <1250 1>, <1251 1>, <1252 1>, <1253 1>, <1254 1>, + <1255 1>, <1256 1>, <1257 1>, <1258 1>, <1259 1>, + <1260 1>, <1261 1>, <1262 1>, <1263 1>, <1264 1>, + <1265 1>, <1266 1>, <1267 1>, <1268 1>, <1269 1>, + <1270 1>, <1271 1>, <1272 1>, <1273 1>, <1274 1>, + <1275 1>, <1276 1>, <1277 1>, <1278 1>, <1279 1>, + <1280 1>, <1281 1>, <1282 1>, <1283 1>, <1284 1>, + <1285 1>, <1286 1>, <1287 1>, <1288 1>, <1289 1>, + <1290 1>, <1291 1>, <1292 1>, <1293 1>, <1294 1>, + <1295 1>, <1296 1>, <1297 1>, <1298 1>, <1299 1>, + <1300 1>, <1301 1>, <1302 1>, <1303 1>, <1304 1>, + <1305 1>, <1306 1>, <1307 1>, <1308 1>, <1309 1>, + <1310 1>, <1311 1>, <1312 1>, <1313 1>, <1314 1>, + <1315 1>, <1316 1>, <1317 1>, <1318 1>, <1319 1>, + <1320 1>, <1321 1>, <1322 1>, <1323 1>, <1324 1>, + <1325 1>, <1326 1>, <1327 1>, <1328 1>, <1329 1>, + <1330 1>, <1331 1>, <1332 1>, <1333 1>, <1334 1>, + <1335 1>, <1336 1>, <1337 1>, <1338 1>, <1339 1>, + <1340 1>, <1341 1>, <1342 1>, <1343 1>; + + desc-num = <0x400>; + buf-size = <0x1000>; + dma-coherent; + + port@0 { + reg = <0>; + serdes-syscon = <&serdes_ctrl>; + port-rst-offset = <0>; + port-mode-offset = <0>; + mc-mac-mask = [ff f0 00 00 00 00]; + media-type = "fiber"; + }; + + port@1 { + reg = <1>; + serdes-syscon= <&serdes_ctrl>; + port-rst-offset = <1>; + port-mode-offset = <1>; + mc-mac-mask = [ff f0 00 00 00 00]; + media-type = "fiber"; + }; + + port@4 { + reg = <4>; + phy-handle = <&phy0>; + serdes-syscon= <&serdes_ctrl>; + port-rst-offset = <4>; + port-mode-offset = <2>; + mc-mac-mask = [ff f0 00 00 00 00]; + media-type = "copper"; + }; + + port@5 { + reg = <5>; + phy-handle = <&phy1>; + serdes-syscon= <&serdes_ctrl>; + port-rst-offset = <5>; + port-mode-offset = <3>; + mc-mac-mask = [ff f0 00 00 00 00]; + media-type = "copper"; + }; + }; + + eth0: ethernet@4{ + compatible = "hisilicon,hns-nic-v2"; + ae-handle = <&dsaf0>; + port-idx-in-ae = <4>; + local-mac-address = [00 00 00 00 00 00]; + status = "disabled"; + dma-coherent; + }; + + eth1: ethernet@5{ + compatible = "hisilicon,hns-nic-v2"; + ae-handle = <&dsaf0>; + port-idx-in-ae = <5>; + local-mac-address = [00 00 00 00 00 00]; + status = "disabled"; + dma-coherent; + }; + + eth2: ethernet@0{ + compatible = "hisilicon,hns-nic-v2"; + ae-handle = <&dsaf0>; + port-idx-in-ae = <0>; + local-mac-address = [00 00 00 00 00 00]; + status = "disabled"; + dma-coherent; + }; + + eth3: ethernet@1{ + compatible = "hisilicon,hns-nic-v2"; + ae-handle = <&dsaf0>; + port-idx-in-ae = <1>; + local-mac-address = [00 00 00 00 00 00]; + status = "disabled"; + dma-coherent; + }; + + infiniband@c4000000 { + compatible = "hisilicon,hns-roce-v1"; + reg = <0x0 0xc4000000 0x0 0x100000>; + dma-coherent; + eth-handle = <ð2 ð3 0 0 ð0 ð1>; + dsaf-handle = <&dsaf0>; + node-guid = [00 9A CD 00 00 01 02 03]; + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&mbigen_dsa_roce>; + interrupts = <722 1>, + <723 1>, + <724 1>, + <725 1>, + <726 1>, + <727 1>, + <728 1>, + <729 1>, + <730 1>, + <731 1>, + <732 1>, + <733 1>, + <734 1>, + <735 1>, + <736 1>, + <737 1>, + <738 1>, + <739 1>, + <740 1>, + <741 1>, + <742 1>, + <743 1>, + <744 1>, + <745 1>, + <746 1>, + <747 1>, + <748 1>, + <749 1>, + <750 1>, + <751 1>, + <752 1>, + <753 1>, + <785 1>, + <754 4>; + + interrupt-names = "hns-roce-comp-0", + "hns-roce-comp-1", + "hns-roce-comp-2", + "hns-roce-comp-3", + "hns-roce-comp-4", + "hns-roce-comp-5", + "hns-roce-comp-6", + "hns-roce-comp-7", + "hns-roce-comp-8", + "hns-roce-comp-9", + "hns-roce-comp-10", + "hns-roce-comp-11", + "hns-roce-comp-12", + "hns-roce-comp-13", + "hns-roce-comp-14", + "hns-roce-comp-15", + "hns-roce-comp-16", + "hns-roce-comp-17", + "hns-roce-comp-18", + "hns-roce-comp-19", + "hns-roce-comp-20", + "hns-roce-comp-21", + "hns-roce-comp-22", + "hns-roce-comp-23", + "hns-roce-comp-24", + "hns-roce-comp-25", + "hns-roce-comp-26", + "hns-roce-comp-27", + "hns-roce-comp-28", + "hns-roce-comp-29", + "hns-roce-comp-30", + "hns-roce-comp-31", + "hns-roce-async", + "hns-roce-common"; + }; + + sas0: sas@c3000000 { + compatible = "hisilicon,hip07-sas-v2"; + reg = <0 0xc3000000 0 0x10000>; + sas-addr = [50 01 88 20 16 00 00 00]; + hisilicon,sas-syscon = <&dsa_subctrl>; + ctrl-reset-reg = <0xa60>; + ctrl-reset-sts-reg = <0x5a30>; + ctrl-clock-ena-reg = <0x338>; + queue-count = <16>; + phy-count = <8>; + dma-coherent; + interrupt-parent = <&mbigen_sas0>; + interrupts = <64 4>,<65 4>,<66 4>,<67 4>,<68 4>, + <69 4>,<70 4>,<71 4>,<72 4>,<73 4>, + <74 4>,<75 4>,<76 4>,<77 4>,<78 4>, + <79 4>,<80 4>,<81 4>,<82 4>,<83 4>, + <84 4>,<85 4>,<86 4>,<87 4>,<88 4>, + <89 4>,<90 4>,<91 4>,<92 4>,<93 4>, + <94 4>,<95 4>,<96 4>,<97 4>,<98 4>, + <99 4>,<100 4>,<101 4>,<102 4>,<103 4>, + <104 4>,<105 4>,<106 4>,<107 4>,<108 4>, + <109 4>,<110 4>,<111 4>,<112 4>,<113 4>, + <114 4>,<115 4>,<116 4>,<117 4>,<118 4>, + <119 4>,<120 4>,<121 4>,<122 4>,<123 4>, + <124 4>,<125 4>,<126 4>,<127 4>,<128 4>, + <129 4>,<130 4>,<131 4>,<132 4>,<133 4>, + <134 4>,<135 4>,<136 4>,<137 4>,<138 4>, + <139 4>,<140 4>,<141 4>,<142 4>,<143 4>, + <144 4>,<145 4>,<146 4>,<147 4>,<148 4>, + <149 4>,<150 4>,<151 4>,<152 4>,<153 4>, + <154 4>,<155 4>,<156 4>,<157 4>,<158 4>, + <159 4>,<601 1>,<602 1>,<603 1>,<604 1>, + <605 1>,<606 1>,<607 1>,<608 1>,<609 1>, + <610 1>,<611 1>,<612 1>,<613 1>,<614 1>, + <615 1>,<616 1>,<617 1>,<618 1>,<619 1>, + <620 1>,<621 1>,<622 1>,<623 1>,<624 1>, + <625 1>,<626 1>,<627 1>,<628 1>,<629 1>, + <630 1>,<631 1>,<632 1>; + status = "disabled"; + }; + + sas1: sas@a2000000 { + compatible = "hisilicon,hip07-sas-v2"; + reg = <0 0xa2000000 0 0x10000>; + sas-addr = [50 01 88 20 16 00 00 00]; + hisilicon,sas-syscon = <&pcie_subctl>; + hip06-sas-v2-quirk-amt; + ctrl-reset-reg = <0xa18>; + ctrl-reset-sts-reg = <0x5a0c>; + ctrl-clock-ena-reg = <0x318>; + queue-count = <16>; + phy-count = <8>; + dma-coherent; + interrupt-parent = <&mbigen_sas1>; + interrupts = <64 4>,<65 4>,<66 4>,<67 4>,<68 4>, + <69 4>,<70 4>,<71 4>,<72 4>,<73 4>, + <74 4>,<75 4>,<76 4>,<77 4>,<78 4>, + <79 4>,<80 4>,<81 4>,<82 4>,<83 4>, + <84 4>,<85 4>,<86 4>,<87 4>,<88 4>, + <89 4>,<90 4>,<91 4>,<92 4>,<93 4>, + <94 4>,<95 4>,<96 4>,<97 4>,<98 4>, + <99 4>,<100 4>,<101 4>,<102 4>,<103 4>, + <104 4>,<105 4>,<106 4>,<107 4>,<108 4>, + <109 4>,<110 4>,<111 4>,<112 4>,<113 4>, + <114 4>,<115 4>,<116 4>,<117 4>,<118 4>, + <119 4>,<120 4>,<121 4>,<122 4>,<123 4>, + <124 4>,<125 4>,<126 4>,<127 4>,<128 4>, + <129 4>,<130 4>,<131 4>,<132 4>,<133 4>, + <134 4>,<135 4>,<136 4>,<137 4>,<138 4>, + <139 4>,<140 4>,<141 4>,<142 4>,<143 4>, + <144 4>,<145 4>,<146 4>,<147 4>,<148 4>, + <149 4>,<150 4>,<151 4>,<152 4>,<153 4>, + <154 4>,<155 4>,<156 4>,<157 4>,<158 4>, + <159 4>,<576 1>,<577 1>,<578 1>,<579 1>, + <580 1>,<581 1>,<582 1>,<583 1>,<584 1>, + <585 1>,<586 1>,<587 1>,<588 1>,<589 1>, + <590 1>,<591 1>,<592 1>,<593 1>,<594 1>, + <595 1>,<596 1>,<597 1>,<598 1>,<599 1>, + <600 1>,<601 1>,<602 1>,<603 1>,<604 1>, + <605 1>,<606 1>,<607 1>; + status = "disabled"; + }; + + sas2: sas@a3000000 { + compatible = "hisilicon,hip07-sas-v2"; + reg = <0 0xa3000000 0 0x10000>; + sas-addr = [50 01 88 20 16 00 00 00]; + hisilicon,sas-syscon = <&pcie_subctl>; + ctrl-reset-reg = <0xae0>; + ctrl-reset-sts-reg = <0x5a70>; + ctrl-clock-ena-reg = <0x3a8>; + queue-count = <16>; + phy-count = <9>; + dma-coherent; + interrupt-parent = <&mbigen_sas2>; + interrupts = <192 4>,<193 4>,<194 4>,<195 4>,<196 4>, + <197 4>,<198 4>,<199 4>,<200 4>,<201 4>, + <202 4>,<203 4>,<204 4>,<205 4>,<206 4>, + <207 4>,<208 4>,<209 4>,<210 4>,<211 4>, + <212 4>,<213 4>,<214 4>,<215 4>,<216 4>, + <217 4>,<218 4>,<219 4>,<220 4>,<221 4>, + <222 4>,<223 4>,<224 4>,<225 4>,<226 4>, + <227 4>,<228 4>,<229 4>,<230 4>,<231 4>, + <232 4>,<233 4>,<234 4>,<235 4>,<236 4>, + <237 4>,<238 4>,<239 4>,<240 4>,<241 4>, + <242 4>,<243 4>,<244 4>,<245 4>,<246 4>, + <247 4>,<248 4>,<249 4>,<250 4>,<251 4>, + <252 4>,<253 4>,<254 4>,<255 4>,<256 4>, + <257 4>,<258 4>,<259 4>,<260 4>,<261 4>, + <262 4>,<263 4>,<264 4>,<265 4>,<266 4>, + <267 4>,<268 4>,<269 4>,<270 4>,<271 4>, + <272 4>,<273 4>,<274 4>,<275 4>,<276 4>, + <277 4>,<278 4>,<279 4>,<280 4>,<281 4>, + <282 4>,<283 4>,<284 4>,<285 4>,<286 4>, + <287 4>,<608 1>,<609 1>,<610 1>,<611 1>, + <612 1>,<613 1>,<614 1>,<615 1>,<616 1>, + <617 1>,<618 1>,<619 1>,<620 1>,<621 1>, + <622 1>,<623 1>,<624 1>,<625 1>,<626 1>, + <627 1>,<628 1>,<629 1>,<630 1>,<631 1>, + <632 1>,<633 1>,<634 1>,<635 1>,<636 1>, + <637 1>,<638 1>,<639 1>; + status = "disabled"; + }; }; }; diff --git a/arch/arm64/boot/dts/include/arm b/arch/arm64/boot/dts/include/arm new file mode 120000 index 000000000000..cf63d80e2b93 --- /dev/null +++ b/arch/arm64/boot/dts/include/arm @@ -0,0 +1 @@ +../../../../arm/boot/dts
\ No newline at end of file diff --git a/arch/arm64/boot/dts/include/arm64 b/arch/arm64/boot/dts/include/arm64 new file mode 120000 index 000000000000..a96aa0ea9d8c --- /dev/null +++ b/arch/arm64/boot/dts/include/arm64 @@ -0,0 +1 @@ +..
\ No newline at end of file diff --git a/arch/arm64/boot/dts/marvell/armada-3720-db.dts b/arch/arm64/boot/dts/marvell/armada-3720-db.dts index 86602c907a61..cef5f976bc0f 100644 --- a/arch/arm64/boot/dts/marvell/armada-3720-db.dts +++ b/arch/arm64/boot/dts/marvell/armada-3720-db.dts @@ -46,6 +46,7 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include "armada-372x.dtsi" / { @@ -60,10 +61,49 @@ device_type = "memory"; reg = <0x00000000 0x00000000 0x00000000 0x20000000>; }; + + exp_usb3_vbus: usb3-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb3-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + gpio = <&gpio_exp 1 GPIO_ACTIVE_HIGH>; + }; + + usb3_phy: usb3-phy { + compatible = "usb-nop-xceiv"; + vcc-supply = <&exp_usb3_vbus>; + }; }; &i2c0 { status = "okay"; + + gpio_exp: pca9555@22 { + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + + reg = <0x22>; + /* + * IO0_0: PWR_EN_USB2 IO1_0: PWR_EN_VTT + * IO0_1: PWR_EN_USB23 IO1_1: MPCIE_WDISABLE + * IO0_2: PWR_EN_SATA IO1_2: RGMII_DEV_RSTN + * IO0_3: PWR_EN_PCIE IO1_3: SGMII_DEV_RSTN + * IO0_4: PWR_EN_SD + * IO0_5: PWR_EN_EMMC + * IO0_6: PWR_EN_RGMII IO1_6: SATA_USB3.0_SEL + * IO0_7: PWR_EN_SGMII IO1_7: PWR_MCI_PS + */ + }; + + rtc@68 { + /* PT7C4337A from pericom fully compatible with the ds1337 */ + compatible = "dallas,ds1337"; + reg = <0x68>; + }; }; /* CON3 */ @@ -106,9 +146,19 @@ status = "okay"; }; +&sdhci0 { + non-removable; + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs400-1_8v; + marvell,pad-type = "fixed-1-8v"; + status = "okay"; +}; + /* CON31 */ &usb3 { status = "okay"; + usb-phy = <&usb3_phy>; }; /* CON17 (PCIe) / CON12 (mini-PCIe) */ @@ -116,6 +166,12 @@ status = "okay"; }; +/* CON27 */ +&usb2 { + status = "okay"; +}; + + &mdio { status = "okay"; phy0: ethernet-phy@0 { diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi index b48d668a6ab6..58ae9e095af2 100644 --- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi @@ -112,6 +112,8 @@ i2c0: i2c@11000 { compatible = "marvell,armada-3700-i2c"; reg = <0x11000 0x24>; + #address-cells = <1>; + #size-cells = <0>; clocks = <&nb_periph_clk 10>; interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; mrvl,i2c-fast-mode; @@ -121,6 +123,8 @@ i2c1: i2c@11080 { compatible = "marvell,armada-3700-i2c"; reg = <0x11080 0x24>; + #address-cells = <1>; + #size-cells = <0>; clocks = <&nb_periph_clk 9>; interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; mrvl,i2c-fast-mode; @@ -196,7 +200,15 @@ compatible = "marvell,armada3700-xhci", "generic-xhci"; reg = <0x58000 0x4000>; - interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sb_periph_clk 12>; + status = "disabled"; + }; + + usb2: usb@5e000 { + compatible = "marvell,armada-3700-ehci"; + reg = <0x5e000 0x2000>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; @@ -213,6 +225,17 @@ }; }; + sdhci0: sdhci@d8000 { + compatible = "marvell,armada-3700-sdhci", + "marvell,sdhci-xenon"; + reg = <0xd8000 0x300 + 0x17808 0x4>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&nb_periph_clk 0>; + clock-names = "core"; + status = "disabled"; + }; + sata: sata@e0000 { compatible = "marvell,armada-3700-ahci"; reg = <0xe0000 0x2000>; diff --git a/arch/arm64/boot/dts/marvell/armada-7040-db.dts b/arch/arm64/boot/dts/marvell/armada-7040-db.dts index 070b589680c5..12442329b80f 100644 --- a/arch/arm64/boot/dts/marvell/armada-7040-db.dts +++ b/arch/arm64/boot/dts/marvell/armada-7040-db.dts @@ -146,3 +146,46 @@ &cpm_usb3_1 { status = "okay"; }; + +&ap_sdhci0 { + status = "okay"; + bus-width = <4>; + no-1-8-v; + non-removable; +}; + +&cpm_sdhci0 { + status = "okay"; + bus-width = <4>; + no-1-8-v; + non-removable; +}; + +&cpm_mdio { + phy0: ethernet-phy@0 { + reg = <0>; + }; + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + +&cpm_ethernet { + status = "okay"; +}; + +&cpm_eth1 { + status = "okay"; + phy = <&phy0>; + phy-mode = "sgmii"; +}; + +&cpm_eth2 { + status = "okay"; + phy = <&phy1>; + phy-mode = "rgmii-id"; +}; + +&cpm_crypto { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/marvell/armada-8020.dtsi b/arch/arm64/boot/dts/marvell/armada-8020.dtsi index 048e5cf5160e..7c08f1f28d9e 100644 --- a/arch/arm64/boot/dts/marvell/armada-8020.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-8020.dtsi @@ -54,3 +54,13 @@ compatible = "marvell,armada8020", "marvell,armada-ap806-dual", "marvell,armada-ap806"; }; + +/* The RTC requires external oscillator. But on Aramda 80x0, the RTC clock + * in CP master is not connected (by package) to the oscillator. So + * disable it. However, the RTC clock in CP slave is connected to the + * oscillator so this one is let enabled. + */ + +&cpm_rtc { + status = "disabled"; +}; diff --git a/arch/arm64/boot/dts/marvell/armada-8040-db.dts b/arch/arm64/boot/dts/marvell/armada-8040-db.dts index 6e6f182fb297..dc0d084005b2 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-db.dts +++ b/arch/arm64/boot/dts/marvell/armada-8040-db.dts @@ -124,6 +124,26 @@ status = "okay"; }; +&cpm_mdio { + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + +&cpm_ethernet { + status = "okay"; +}; + +&cpm_eth2 { + status = "okay"; + phy = <&phy1>; + phy-mode = "rgmii-id"; +}; + +&cpm_crypto { + status = "okay"; +}; + /* CON5 on CP1 expansion */ &cps_pcie2 { status = "okay"; @@ -148,3 +168,15 @@ &cps_usb3_1 { status = "okay"; }; + +&ap_sdhci0 { + status = "okay"; + bus-width = <4>; + non-removable; +}; + +&cpm_sdhci0 { + status = "okay"; + bus-width = <8>; + non-removable; +}; diff --git a/arch/arm64/boot/dts/marvell/armada-8040.dtsi b/arch/arm64/boot/dts/marvell/armada-8040.dtsi index 9c1b28c47683..33813a75bc30 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-8040.dtsi @@ -54,3 +54,12 @@ compatible = "marvell,armada8040", "marvell,armada-ap806-quad", "marvell,armada-ap806"; }; + +/* The RTC requires external oscillator. But on Aramda 80x0, the RTC clock + * in CP master is not connected (by package) to the oscillator. So + * disable it. However, the RTC clock in CP slave is connected to the + * oscillator so this one is let enabled. + */ +&cpm_rtc { + status = "disabled"; +}; diff --git a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi index a749ba2edec4..fe41bf9c301e 100644 --- a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi @@ -229,13 +229,25 @@ }; + ap_sdhci0: sdhci@6e0000 { + compatible = "marvell,armada-ap806-sdhci"; + reg = <0x6e0000 0x300>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "core"; + clocks = <&ap_syscon 4>; + dma-coherent; + marvell,xenon-phy-slow-mode; + status = "disabled"; + }; + ap_syscon: system-controller@6f4000 { compatible = "marvell,ap806-system-controller", "syscon"; #clock-cells = <1>; clock-output-names = "ap-cpu-cluster-0", "ap-cpu-cluster-1", - "ap-fixed", "ap-mss"; + "ap-fixed", "ap-mss", + "ap-emmc"; reg = <0x6f4000 0x1000>; }; }; diff --git a/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi index 3a99c36433d6..ac8df5201cd6 100644 --- a/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi @@ -59,6 +59,43 @@ interrupt-parent = <&gic>; ranges = <0x0 0x0 0xf2000000 0x2000000>; + cpm_ethernet: ethernet@0 { + compatible = "marvell,armada-7k-pp22"; + reg = <0x0 0x100000>, <0x129000 0xb000>; + clocks = <&cpm_syscon0 1 3>, <&cpm_syscon0 1 9>, <&cpm_syscon0 1 5>; + clock-names = "pp_clk", "gop_clk", "mg_clk"; + status = "disabled"; + dma-coherent; + + cpm_eth0: eth0 { + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + port-id = <0>; + gop-port-id = <0>; + status = "disabled"; + }; + + cpm_eth1: eth1 { + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + port-id = <1>; + gop-port-id = <2>; + status = "disabled"; + }; + + cpm_eth2: eth2 { + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + port-id = <2>; + gop-port-id = <3>; + status = "disabled"; + }; + }; + + cpm_mdio: mdio@12a200 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,orion-mdio"; + reg = <0x12a200 0x10>; + }; + cpm_syscon0: system-controller@440000 { compatible = "marvell,cp110-system-controller0", "syscon"; @@ -79,6 +116,13 @@ "cpm-usb3dev", "cpm-eip150", "cpm-eip197"; }; + cpm_rtc: rtc@284000 { + compatible = "marvell,armada-8k-rtc"; + reg = <0x284000 0x20>, <0x284080 0x24>; + reg-names = "rtc", "rtc-soc"; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + }; + cpm_sata0: sata@540000 { compatible = "marvell,armada-8k-ahci", "generic-ahci"; @@ -173,6 +217,32 @@ clocks = <&cpm_syscon0 1 25>; status = "okay"; }; + + cpm_sdhci0: sdhci@780000 { + compatible = "marvell,armada-cp110-sdhci"; + reg = <0x780000 0x300>; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "core"; + clocks = <&cpm_syscon0 1 4>; + dma-coherent; + status = "disabled"; + }; + + cpm_crypto: crypto@800000 { + compatible = "inside-secure,safexcel-eip197"; + reg = <0x800000 0x200000>; + interrupts = <GIC_SPI 34 (IRQ_TYPE_EDGE_RISING + | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "mem", "ring0", "ring1", + "ring2", "ring3", "eip"; + clocks = <&cpm_syscon0 1 26>; + status = "disabled"; + }; }; cpm_pcie0: pcie@f2600000 { diff --git a/arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi index 9e09c4d3b6bd..7740a75a8230 100644 --- a/arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi @@ -59,6 +59,50 @@ interrupt-parent = <&gic>; ranges = <0x0 0x0 0xf4000000 0x2000000>; + cps_rtc: rtc@284000 { + compatible = "marvell,armada-8k-rtc"; + reg = <0x284000 0x20>, <0x284080 0x24>; + reg-names = "rtc", "rtc-soc"; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + }; + + cps_ethernet: ethernet@0 { + compatible = "marvell,armada-7k-pp22"; + reg = <0x0 0x100000>, <0x129000 0xb000>; + clocks = <&cps_syscon0 1 3>, <&cps_syscon0 1 9>, <&cps_syscon0 1 5>; + clock-names = "pp_clk", "gop_clk", "mg_clk"; + status = "disabled"; + dma-coherent; + + cps_eth0: eth0 { + interrupts = <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>; + port-id = <0>; + gop-port-id = <0>; + status = "disabled"; + }; + + cps_eth1: eth1 { + interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>; + port-id = <1>; + gop-port-id = <2>; + status = "disabled"; + }; + + cps_eth2: eth2 { + interrupts = <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>; + port-id = <2>; + gop-port-id = <3>; + status = "disabled"; + }; + }; + + cps_mdio: mdio@12a200 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,orion-mdio"; + reg = <0x12a200 0x10>; + }; + cps_syscon0: system-controller@440000 { compatible = "marvell,cp110-system-controller0", "syscon"; @@ -173,6 +217,22 @@ clocks = <&cps_syscon0 1 25>; status = "okay"; }; + + cps_crypto: crypto@800000 { + compatible = "inside-secure,safexcel-eip197"; + reg = <0x800000 0x200000>; + interrupts = <GIC_SPI 34 (IRQ_TYPE_EDGE_RISING + | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "mem", "ring0", "ring1", + "ring2", "ring3", "eip"; + clocks = <&cps_syscon0 1 26>; + status = "disabled"; + }; }; cps_pcie0: pcie@f4600000 { diff --git a/arch/arm64/boot/dts/nvidia/tegra132.dtsi b/arch/arm64/boot/dts/nvidia/tegra132.dtsi index 3f3a46a4bd01..2b17936ac5be 100644 --- a/arch/arm64/boot/dts/nvidia/tegra132.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra132.dtsi @@ -224,7 +224,7 @@ }; flow-controller@60007000 { - compatible = "nvidia,tegra124-flowctrl"; + compatible = "nvidia,tegra132-flowctrl", "nvidia,tegra124-flowctrl"; reg = <0x0 0x60007000 0x0 0x1000>; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts index 0d3c0996d832..8daadadec63a 100644 --- a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts @@ -1,8 +1,99 @@ /dts-v1/; +#include <dt-bindings/input/linux-event-codes.h> + #include "tegra186-p3310.dtsi" / { model = "NVIDIA Tegra186 P2771-0000 Development Board"; compatible = "nvidia,p2771-0000", "nvidia,tegra186"; + + i2c@3160000 { + power-monitor@42 { + compatible = "ti,ina3221"; + reg = <0x42>; + }; + + power-monitor@43 { + compatible = "ti,ina3221"; + reg = <0x43>; + }; + + exp1: gpio@74 { + compatible = "ti,tca9539"; + reg = <0x74>; + + interrupt-parent = <&gpio>; + interrupts = <TEGRA_MAIN_GPIO(Y, 0) GPIO_ACTIVE_LOW>; + + #gpio-cells = <2>; + gpio-controller; + }; + + exp2: gpio@77 { + compatible = "ti,tca9539"; + reg = <0x77>; + + interrupt-parent = <&gpio>; + interrupts = <TEGRA_MAIN_GPIO(Y, 6) GPIO_ACTIVE_LOW>; + + #gpio-cells = <2>; + gpio-controller; + }; + }; + + /* SDMMC1 (SD/MMC) */ + sdhci@3400000 { + status = "okay"; + + vmmc-supply = <&vdd_sd>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + power { + label = "Power"; + gpios = <&gpio_aon TEGRA_AON_GPIO(FF, 0) + GPIO_ACTIVE_LOW>; + linux,input-type = <EV_KEY>; + linux,code = <KEY_POWER>; + debounce-interval = <10>; + wakeup-source; + }; + + volume-up { + label = "Volume Up"; + gpios = <&gpio_aon TEGRA_AON_GPIO(FF, 1) + GPIO_ACTIVE_LOW>; + linux,input-type = <EV_KEY>; + linux,code = <KEY_VOLUMEUP>; + debounce-interval = <10>; + }; + + volume-down { + label = "Volume Down"; + gpios = <&gpio_aon TEGRA_AON_GPIO(FF, 2) + GPIO_ACTIVE_LOW>; + linux,input-type = <EV_KEY>; + linux,code = <KEY_VOLUMEDOWN>; + debounce-interval = <10>; + }; + }; + + regulators { + vdd_sd: regulator@100 { + compatible = "regulator-fixed"; + reg = <100>; + + regulator-name = "SD_CARD_SW_PWR"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio TEGRA_MAIN_GPIO(P, 6) GPIO_ACTIVE_HIGH>; + enable-active-high; + + vin-supply = <&vdd_3v3_sys>; + }; + }; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi b/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi index 1abe2eceb3d1..cf84d7046ad5 100644 --- a/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi @@ -1,11 +1,23 @@ #include "tegra186.dtsi" +#include <dt-bindings/mfd/max77620.h> + / { model = "NVIDIA Tegra186 P3310 Processor Module"; compatible = "nvidia,p3310", "nvidia,tegra186"; aliases { + sdhci0 = "/sdhci@3460000"; + sdhci1 = "/sdhci@3400000"; serial0 = &uarta; + i2c0 = "/bpmp/i2c"; + i2c1 = "/i2c@3160000"; + i2c2 = "/i2c@c240000"; + i2c3 = "/i2c@3180000"; + i2c4 = "/i2c@3190000"; + i2c5 = "/i2c@31c0000"; + i2c6 = "/i2c@c250000"; + i2c7 = "/i2c@31e0000"; }; chosen { @@ -18,14 +30,99 @@ reg = <0x0 0x80000000 0x2 0x00000000>; }; + ethernet@2490000 { + status = "okay"; + + phy-reset-gpios = <&gpio TEGRA_MAIN_GPIO(M, 4) GPIO_ACTIVE_LOW>; + phy-handle = <&phy>; + phy-mode = "rgmii"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy: phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0x0>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_MAIN_GPIO(M, 5) IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; + serial@3100000 { status = "okay"; }; + i2c@3160000 { + status = "okay"; + + power-monitor@40 { + compatible = "ti,ina3221"; + reg = <0x40>; + }; + + power-monitor@41 { + compatible = "ti,ina3221"; + reg = <0x41>; + }; + }; + + i2c@3180000 { + status = "okay"; + }; + + i2c@3190000 { + status = "okay"; + }; + + i2c@31c0000 { + status = "okay"; + }; + + i2c@31e0000 { + status = "okay"; + }; + + /* SDMMC1 (SD/MMC) */ + sdhci@3400000 { + cd-gpios = <&gpio TEGRA_MAIN_GPIO(P, 5) GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio TEGRA_MAIN_GPIO(P, 4) GPIO_ACTIVE_LOW>; + + vqmmc-supply = <&vddio_sdmmc1>; + }; + + /* SDMMC3 (SDIO) */ + sdhci@3440000 { + status = "okay"; + }; + + /* SDMMC4 (eMMC) */ + sdhci@3460000 { + status = "okay"; + bus-width = <8>; + non-removable; + + vqmmc-supply = <&vdd_1v8_ap>; + vmmc-supply = <&vdd_3v3_sys>; + }; + hsp@3c00000 { status = "okay"; }; + i2c@c240000 { + status = "okay"; + }; + + i2c@c250000 { + status = "okay"; + }; + + pmc@c360000 { + nvidia,invert-interrupt; + }; + cpus { cpu@0 { enable-method = "psci"; @@ -53,7 +150,192 @@ }; bpmp { - status = "okay"; + i2c { + status = "okay"; + + pmic: pmic@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + + interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + #interrupt-cells = <2>; + interrupt-controller; + + #gpio-cells = <2>; + gpio-controller; + + pinctrl-names = "default"; + pinctrl-0 = <&max77620_default>; + + max77620_default: pinmux { + gpio0 { + pins = "gpio0"; + function = "gpio"; + }; + + gpio1 { + pins = "gpio1"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + gpio2 { + pins = "gpio2"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + + gpio3 { + pins = "gpio3"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + + gpio4 { + pins = "gpio4"; + function = "32k-out1"; + drive-push-pull = <1>; + }; + + gpio5 { + pins = "gpio5"; + function = "gpio"; + drive-push-pull = <0>; + }; + + gpio6 { + pins = "gpio6"; + function = "gpio"; + drive-push-pull = <1>; + }; + + gpio7 { + pins = "gpio7"; + function = "gpio"; + drive-push-pull = <0>; + }; + }; + + fps { + fps0 { + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>; + maxim,shutdown-fps-time-period-us = <640>; + }; + + fps1 { + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>; + maxim,shutdown-fps-time-period-us = <640>; + }; + + fps2 { + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>; + maxim,shutdown-fps-time-period-us = <640>; + }; + }; + + regulators { + in-sd0-supply = <&vdd_5v0_sys>; + in-sd1-supply = <&vdd_5v0_sys>; + in-sd2-supply = <&vdd_5v0_sys>; + in-sd3-supply = <&vdd_5v0_sys>; + + in-ldo0-1-supply = <&vdd_5v0_sys>; + in-ldo2-supply = <&vdd_5v0_sys>; + in-ldo3-5-supply = <&vdd_5v0_sys>; + in-ldo4-6-supply = <&vdd_1v8>; + in-ldo7-8-supply = <&avdd_dsi_csi>; + + sd0 { + regulator-name = "VDD_DDR_1V1_PMIC"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + }; + + avdd_dsi_csi: sd1 { + regulator-name = "AVDD_DSI_CSI_1V2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + /* XXX */ + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8: sd2 { + regulator-name = "VDD_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + /* XXX */ + regulator-always-on; + regulator-boot-on; + }; + + vdd_3v3_sys: sd3 { + regulator-name = "VDD_3V3_SYS"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + /* XXX */ + regulator-always-on; + regulator-boot-on; + }; + + ldo0 { + regulator-name = "VDD_1V8_AP_PLL"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + /* XXX */ + regulator-always-on; + regulator-boot-on; + }; + + ldo2 { + regulator-name = "VDDIO_3V3_AOHV"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + /* XXX */ + regulator-always-on; + regulator-boot-on; + }; + + vddio_sdmmc1: ldo3 { + regulator-name = "VDDIO_SDMMC1_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + ldo4 { + regulator-name = "VDD_RTC"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + vddio_sdmmc3: ldo5 { + regulator-name = "VDDIO_SDMMC3_AP"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + avdd_1v05: ldo7 { + regulator-name = "VDD_HDMI_1V05"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + /* XXX */ + regulator-always-on; + regulator-boot-on; + }; + + vdd_pex: ldo8 { + regulator-name = "VDD_PEX_1V05"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + /* XXX */ + regulator-always-on; + regulator-boot-on; + }; + }; + }; + }; }; psci { @@ -61,4 +343,39 @@ status = "okay"; method = "smc"; }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + vdd_5v0_sys: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + + regulator-name = "VDD_5V0_SYS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8_ap: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + + regulator-name = "VDD_1V8_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + /* XXX */ + regulator-always-on; + regulator-boot-on; + + gpio = <&pmic 1 GPIO_ACTIVE_HIGH>; + enable-active-high; + + vin-supply = <&vdd_1v8>; + }; + }; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra186.dtsi b/arch/arm64/boot/dts/nvidia/tegra186.dtsi index 62fa85ae0271..5e62e68ac053 100644 --- a/arch/arm64/boot/dts/nvidia/tegra186.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra186.dtsi @@ -2,6 +2,7 @@ #include <dt-bindings/gpio/tegra186-gpio.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/mailbox/tegra186-hsp.h> +#include <dt-bindings/power/tegra186-powergate.h> #include <dt-bindings/reset/tegra186-reset.h> / { @@ -27,6 +28,37 @@ gpio-controller; }; + ethernet@2490000 { + compatible = "nvidia,tegra186-eqos", + "snps,dwc-qos-ethernet-4.10"; + reg = <0x0 0x02490000 0x0 0x10000>; + interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>, /* common */ + <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>, /* power */ + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, /* rx0 */ + <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>, /* tx0 */ + <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>, /* rx1 */ + <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>, /* tx1 */ + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>, /* rx2 */ + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* tx2 */ + <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>, /* rx3 */ + <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>; /* tx3 */ + clocks = <&bpmp TEGRA186_CLK_AXI_CBB>, + <&bpmp TEGRA186_CLK_EQOS_AXI>, + <&bpmp TEGRA186_CLK_EQOS_RX>, + <&bpmp TEGRA186_CLK_EQOS_TX>, + <&bpmp TEGRA186_CLK_EQOS_PTP_REF>; + clock-names = "master_bus", "slave_bus", "rx", "tx", "ptp_ref"; + resets = <&bpmp TEGRA186_RESET_EQOS>; + reset-names = "eqos"; + status = "disabled"; + + snps,write-requests = <1>; + snps,read-requests = <3>; + snps,burst-map = <0x7>; + snps,txpbl = <32>; + snps,rxpbl = <8>; + }; + uarta: serial@3100000 { compatible = "nvidia,tegra186-uart", "nvidia,tegra20-uart"; reg = <0x0 0x03100000 0x0 0x40>; @@ -307,6 +339,33 @@ #interrupt-cells = <2>; }; + pmc@c360000 { + compatible = "nvidia,tegra186-pmc"; + reg = <0 0x0c360000 0 0x10000>, + <0 0x0c370000 0 0x10000>, + <0 0x0c380000 0 0x10000>, + <0 0x0c390000 0 0x10000>; + reg-names = "pmc", "wake", "aotag", "scratch"; + }; + + gpu@17000000 { + compatible = "nvidia,gp10b"; + reg = <0x0 0x17000000 0x0 0x1000000>, + <0x0 0x18000000 0x0 0x1000000>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "stall", "nonstall"; + + clocks = <&bpmp TEGRA186_CLK_GPCCLK>, + <&bpmp TEGRA186_CLK_GPU>; + clock-names = "gpu", "pwr"; + resets = <&bpmp TEGRA186_RESET_GPU>; + reset-names = "gpu"; + status = "disabled"; + + power-domains = <&bpmp TEGRA186_POWER_DOMAIN_GPU>; + }; + sysram@30000000 { compatible = "nvidia,tegra186-sysram", "mmio-sram"; reg = <0x0 0x30000000 0x0 0x50000>; diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi b/arch/arm64/boot/dts/nvidia/tegra210.dtsi index 2f832df29da8..8f26c4d4409a 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi @@ -89,6 +89,8 @@ ranges = <0x0 0x54000000 0x0 0x54000000 0x0 0x01000000>; + iommus = <&mc TEGRA_SWGROUP_HC>; + dpaux1: dpaux@54040000 { compatible = "nvidia,tegra210-dpaux"; reg = <0x0 0x54040000 0x0 0x00040000>; @@ -185,7 +187,14 @@ vic@54340000 { compatible = "nvidia,tegra210-vic"; reg = <0x0 0x54340000 0x0 0x00040000>; - status = "disabled"; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_VIC03>; + clock-names = "vic"; + resets = <&tegra_car 178>; + reset-names = "vic"; + + iommus = <&mc TEGRA_SWGROUP_VIC>; + power-domains = <&pd_vic>; }; nvjpg@54380000 { @@ -755,6 +764,14 @@ resets = <&tegra_car TEGRA210_CLK_XUSB_HOST>; #power-domain-cells = <0>; }; + + pd_vic: vic { + clocks = <&tegra_car TEGRA210_CLK_VIC03>; + clock-names = "vic"; + resets = <&tegra_car 178>; + reset-names = "vic"; + #power-domain-cells = <0>; + }; }; }; diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi index eac5389f2f38..a17f5b9a5de6 100644 --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi @@ -35,6 +35,17 @@ stdout-path = "serial0"; }; + reserved-memory { + ramoops@bff00000{ + compatible = "ramoops"; + reg = <0x0 0xbff00000 0x0 0x100000>; + + record-size = <0x20000>; + console-size = <0x20000>; + ftrace-size = <0x20000>; + }; + }; + soc { dma@7884000 { status = "okay"; diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi index 68a8e67cba29..ab3093995ded 100644 --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi @@ -157,7 +157,7 @@ }; pmu { - compatible = "arm,armv8-pmuv3"; + compatible = "arm,cortex-a53-pmu"; interrupts = <GIC_PPI 7 GIC_CPU_MASK_SIMPLE(4)>; }; @@ -833,8 +833,9 @@ clocks = <&gcc GCC_MSS_CFG_AHB_CLK>, <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>, - <&gcc GCC_BOOT_ROM_AHB_CLK>; - clock-names = "iface", "bus", "mem"; + <&gcc GCC_BOOT_ROM_AHB_CLK>, + <&xo_board>; + clock-names = "iface", "bus", "mem", "xo"; qcom,smem-states = <&hexagon_smp2p_out 0>; qcom,smem-state-names = "stop"; @@ -842,6 +843,7 @@ resets = <&scm 0>; reset-names = "mss_restart"; + cx-supply = <&pm8916_s1>; mx-supply = <&pm8916_l3>; pll-supply = <&pm8916_l7>; @@ -856,6 +858,16 @@ mpss { memory-region = <&mpss_mem>; }; + + smd-edge { + interrupts = <0 25 IRQ_TYPE_EDGE_RISING>; + + qcom,smd-edge = <0>; + qcom,ipc = <&apcs 8 12>; + qcom,remote-pid = <1>; + + label = "hexagon"; + }; }; pronto: wcnss@a21b000 { @@ -1214,14 +1226,6 @@ }; }; }; - - hexagon { - interrupts = <0 25 IRQ_TYPE_EDGE_RISING>; - - qcom,smd-edge = <0>; - qcom,ipc = <&apcs 8 12>; - qcom,remote-pid = <1>; - }; }; hexagon-smp2p { diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi index ed7223d3c8cb..9bc9c857a000 100644 --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi @@ -534,6 +534,26 @@ }; }; + adsp-pil { + compatible = "qcom,msm8996-adsp-pil"; + + interrupts-extended = <&intc 0 162 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", + "handover", "stop-ack"; + + clocks = <&xo_board>; + clock-names = "xo"; + + memory-region = <&adsp_region>; + + qcom,smem-states = <&adsp_smp2p_out 0>; + qcom,smem-state-names = "stop"; + }; + adsp-smp2p { compatible = "qcom,smp2p"; qcom,smem = <443>, <429>; @@ -547,7 +567,7 @@ adsp_smp2p_out: master-kernel { qcom,entry-name = "master-kernel"; - #qcom,state-cells = <1>; + #qcom,smem-state-cells = <1>; }; adsp_smp2p_in: slave-kernel { @@ -557,5 +577,29 @@ #interrupt-cells = <2>; }; }; + + smp2p-slpi { + compatible = "qcom,smp2p"; + qcom,smem = <481>, <430>; + + interrupts = <GIC_SPI 178 IRQ_TYPE_EDGE_RISING>; + + qcom,ipc = <&apcs 16 26>; + + qcom,local-pid = <0>; + qcom,remote-pid = <3>; + + slpi_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + interrupt-controller; + #interrupt-cells = <2>; + }; + + slpi_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + }; + }; #include "msm8996-pins.dtsi" diff --git a/arch/arm64/boot/dts/qcom/pm8994.dtsi b/arch/arm64/boot/dts/qcom/pm8994.dtsi index 0f1866024ae3..b413e44fd09e 100644 --- a/arch/arm64/boot/dts/qcom/pm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8994.dtsi @@ -9,6 +9,13 @@ #address-cells = <1>; #size-cells = <0>; + rtc@6000 { + compatible = "qcom,pm8941-rtc"; + reg = <0x6000>, <0x6100>; + reg-names = "rtc", "alarm"; + interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; + }; + pm8994_gpios: gpios@c000 { compatible = "qcom,pm8994-gpio"; reg = <0xc000>; diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts index c5f8f69a4f5f..ab352159de65 100644 --- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts +++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts @@ -33,6 +33,21 @@ reg = <0x0 0x48000000 0x0 0x38000000>; }; + memory@500000000 { + device_type = "memory"; + reg = <0x5 0x00000000 0x0 0x40000000>; + }; + + memory@600000000 { + device_type = "memory"; + reg = <0x6 0x00000000 0x0 0x40000000>; + }; + + memory@700000000 { + device_type = "memory"; + reg = <0x7 0x00000000 0x0 0x40000000>; + }; + leds { compatible = "gpio-leds"; @@ -213,7 +228,6 @@ &scif_clk { clock-frequency = <14745600>; - status = "okay"; }; &i2c2 { @@ -339,18 +353,7 @@ status = "okay"; phy0: ethernet-phy@0 { - rxc-skew-ps = <900>; - rxdv-skew-ps = <0>; - rxd0-skew-ps = <0>; - rxd1-skew-ps = <0>; - rxd2-skew-ps = <0>; - rxd3-skew-ps = <0>; - txc-skew-ps = <900>; - txen-skew-ps = <0>; - txd0-skew-ps = <0>; - txd1-skew-ps = <0>; - txd2-skew-ps = <0>; - txd3-skew-ps = <0>; + rxc-skew-ps = <1500>; reg = <0>; interrupt-parent = <&gpio2>; interrupts = <11 IRQ_TYPE_LEVEL_LOW>; diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts index 7a8986edcdc0..639aa085d996 100644 --- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts +++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts @@ -56,7 +56,7 @@ reg = <0x0 0x48000000 0x0 0x38000000>; }; - x12_clk: x12_clk { + x12_clk: x12 { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <24576000>; @@ -247,8 +247,22 @@ }; avb_pins: avb { - groups = "avb_mdc"; - function = "avb"; + mux { + groups = "avb_link", "avb_phy_int", "avb_mdc", + "avb_mii"; + function = "avb"; + }; + + pins_mdc { + groups = "avb_mdc"; + drive-strength = <24>; + }; + + pins_mii_tx { + pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0", + "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3"; + drive-strength = <12>; + }; }; du_pins: du { @@ -348,7 +362,6 @@ &scif_clk { clock-frequency = <14745600>; - status = "okay"; }; &i2c2 { @@ -485,6 +498,10 @@ clock-frequency = <22579200>; }; +&i2c_dvfs { + status = "okay"; +}; + &avb { pinctrl-0 = <&avb_pins>; pinctrl-names = "default"; @@ -493,18 +510,7 @@ status = "okay"; phy0: ethernet-phy@0 { - rxc-skew-ps = <900>; - rxdv-skew-ps = <0>; - rxd0-skew-ps = <0>; - rxd1-skew-ps = <0>; - rxd2-skew-ps = <0>; - rxd3-skew-ps = <0>; - txc-skew-ps = <900>; - txen-skew-ps = <0>; - txd0-skew-ps = <0>; - txd1-skew-ps = <0>; - txd2-skew-ps = <0>; - txd3-skew-ps = <0>; + rxc-skew-ps = <1500>; reg = <0>; interrupt-parent = <&gpio2>; interrupts = <11 IRQ_TYPE_LEVEL_LOW>; @@ -567,7 +573,6 @@ &pcie_bus_clk { clock-frequency = <100000000>; - status = "okay"; }; &pciec0 { diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi index eac4f29aa5cd..e99d6443b3e4 100644 --- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi @@ -25,10 +25,11 @@ i2c4 = &i2c4; i2c5 = &i2c5; i2c6 = &i2c6; + i2c7 = &i2c_dvfs; }; psci { - compatible = "arm,psci-0.2"; + compatible = "arm,psci-1.0", "arm,psci-0.2"; method = "smc"; }; @@ -72,17 +73,51 @@ enable-method = "psci"; }; - L2_CA57: cache-controller@0 { + a53_0: cpu@100 { + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x100>; + device_type = "cpu"; + power-domains = <&sysc R8A7795_PD_CA53_CPU0>; + next-level-cache = <&L2_CA53>; + enable-method = "psci"; + }; + + a53_1: cpu@101 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x101>; + device_type = "cpu"; + power-domains = <&sysc R8A7795_PD_CA53_CPU1>; + next-level-cache = <&L2_CA53>; + enable-method = "psci"; + }; + + a53_2: cpu@102 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x102>; + device_type = "cpu"; + power-domains = <&sysc R8A7795_PD_CA53_CPU2>; + next-level-cache = <&L2_CA53>; + enable-method = "psci"; + }; + + a53_3: cpu@103 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x103>; + device_type = "cpu"; + power-domains = <&sysc R8A7795_PD_CA53_CPU3>; + next-level-cache = <&L2_CA53>; + enable-method = "psci"; + }; + + L2_CA57: cache-controller-0 { compatible = "cache"; - reg = <0>; power-domains = <&sysc R8A7795_PD_CA57_SCU>; cache-unified; cache-level = <2>; }; - L2_CA53: cache-controller@100 { + L2_CA53: cache-controller-1 { compatible = "cache"; - reg = <0x100>; power-domains = <&sysc R8A7795_PD_CA53_SCU>; cache-unified; cache-level = <2>; @@ -165,10 +200,11 @@ <0x0 0xf1040000 0 0x20000>, <0x0 0xf1060000 0 0x20000>; interrupts = <GIC_PPI 9 - (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>; clocks = <&cpg CPG_MOD 408>; clock-names = "clk"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 408>; }; wdt0: watchdog@e6020000 { @@ -176,6 +212,7 @@ reg = <0 0xe6020000 0 0x0c>; clocks = <&cpg CPG_MOD 402>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 402>; status = "disabled"; }; @@ -191,6 +228,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 912>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 912>; }; gpio1: gpio@e6051000 { @@ -205,6 +243,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 911>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 911>; }; gpio2: gpio@e6052000 { @@ -219,6 +258,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 910>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 910>; }; gpio3: gpio@e6053000 { @@ -233,6 +273,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 909>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 909>; }; gpio4: gpio@e6054000 { @@ -247,6 +288,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 908>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 908>; }; gpio5: gpio@e6055000 { @@ -261,6 +303,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 907>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 907>; }; gpio6: gpio@e6055400 { @@ -275,6 +318,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 906>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 906>; }; gpio7: gpio@e6055800 { @@ -289,6 +333,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 905>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 905>; }; pmu_a57 { @@ -303,16 +348,28 @@ <&a57_3>; }; + pmu_a53 { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&a53_0>, + <&a53_1>, + <&a53_2>, + <&a53_3>; + }; + timer { compatible = "arm,armv8-timer"; interrupts = <GIC_PPI 13 - (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 14 - (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 11 - (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 10 - (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; }; cpg: clock-controller@e6150000 { @@ -322,6 +379,7 @@ clock-names = "extal", "extalr"; #clock-cells = <2>; #power-domain-cells = <0>; + #reset-cells = <1>; }; rst: reset-controller@e6160000 { @@ -358,6 +416,7 @@ GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 407>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 407>; }; dmac0: dma-controller@e6700000 { @@ -389,6 +448,7 @@ clocks = <&cpg CPG_MOD 219>; clock-names = "fck"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 219>; #dma-cells = <1>; dma-channels = <16>; }; @@ -422,6 +482,7 @@ clocks = <&cpg CPG_MOD 218>; clock-names = "fck"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 218>; #dma-cells = <1>; dma-channels = <16>; }; @@ -455,6 +516,7 @@ clocks = <&cpg CPG_MOD 217>; clock-names = "fck"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 217>; #dma-cells = <1>; dma-channels = <16>; }; @@ -488,6 +550,7 @@ clocks = <&cpg CPG_MOD 502>; clock-names = "fck"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 502>; #dma-cells = <1>; dma-channels = <16>; }; @@ -521,6 +584,7 @@ clocks = <&cpg CPG_MOD 501>; clock-names = "fck"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 501>; #dma-cells = <1>; dma-channels = <16>; }; @@ -563,7 +627,8 @@ "ch24"; clocks = <&cpg CPG_MOD 812>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; - phy-mode = "rgmii-id"; + resets = <&cpg 812>; + phy-mode = "rgmii-txid"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -581,6 +646,7 @@ assigned-clocks = <&cpg CPG_CORE R8A7795_CLK_CANFD>; assigned-clock-rates = <40000000>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 916>; status = "disabled"; }; @@ -596,6 +662,7 @@ assigned-clocks = <&cpg CPG_CORE R8A7795_CLK_CANFD>; assigned-clock-rates = <40000000>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 915>; status = "disabled"; }; @@ -612,6 +679,7 @@ assigned-clocks = <&cpg CPG_CORE R8A7795_CLK_CANFD>; assigned-clock-rates = <40000000>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 914>; status = "disabled"; channel0 { @@ -636,6 +704,7 @@ dmas = <&dmac1 0x31>, <&dmac1 0x30>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 520>; status = "disabled"; }; @@ -652,6 +721,7 @@ dmas = <&dmac1 0x33>, <&dmac1 0x32>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 519>; status = "disabled"; }; @@ -668,6 +738,7 @@ dmas = <&dmac1 0x35>, <&dmac1 0x34>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 518>; status = "disabled"; }; @@ -684,6 +755,7 @@ dmas = <&dmac0 0x37>, <&dmac0 0x36>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 517>; status = "disabled"; }; @@ -700,6 +772,7 @@ dmas = <&dmac0 0x39>, <&dmac0 0x38>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 516>; status = "disabled"; }; @@ -715,6 +788,7 @@ dmas = <&dmac1 0x51>, <&dmac1 0x50>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 207>; status = "disabled"; }; @@ -730,6 +804,7 @@ dmas = <&dmac1 0x53>, <&dmac1 0x52>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 206>; status = "disabled"; }; @@ -745,6 +820,7 @@ dmas = <&dmac1 0x13>, <&dmac1 0x12>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 310>; status = "disabled"; }; @@ -760,6 +836,7 @@ dmas = <&dmac0 0x57>, <&dmac0 0x56>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 204>; status = "disabled"; }; @@ -775,6 +852,7 @@ dmas = <&dmac0 0x59>, <&dmac0 0x58>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 203>; status = "disabled"; }; @@ -790,6 +868,21 @@ dmas = <&dmac1 0x5b>, <&dmac1 0x5a>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 202>; + status = "disabled"; + }; + + i2c_dvfs: i2c@e60b0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,iic-r8a7795", + "renesas,rcar-gen3-iic", + "renesas,rmobile-iic"; + reg = <0 0xe60b0000 0 0x425>; + interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 926>; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 926>; status = "disabled"; }; @@ -802,6 +895,7 @@ interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 931>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 931>; dmas = <&dmac1 0x91>, <&dmac1 0x90>; dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <110>; @@ -817,6 +911,7 @@ interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 930>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 930>; dmas = <&dmac1 0x93>, <&dmac1 0x92>; dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <6>; @@ -832,6 +927,7 @@ interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 929>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 929>; dmas = <&dmac1 0x95>, <&dmac1 0x94>; dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <6>; @@ -847,6 +943,7 @@ interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 928>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 928>; dmas = <&dmac0 0x97>, <&dmac0 0x96>; dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <110>; @@ -862,6 +959,7 @@ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 927>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 927>; dmas = <&dmac0 0x99>, <&dmac0 0x98>; dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <110>; @@ -877,6 +975,7 @@ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 919>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 919>; dmas = <&dmac0 0x9b>, <&dmac0 0x9a>; dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <110>; @@ -892,6 +991,7 @@ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 918>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 918>; dmas = <&dmac0 0x9d>, <&dmac0 0x9c>; dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <6>; @@ -903,6 +1003,7 @@ reg = <0 0xe6e30000 0 0x8>; clocks = <&cpg CPG_MOD 523>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 523>; #pwm-cells = <2>; status = "disabled"; }; @@ -912,6 +1013,7 @@ reg = <0 0xe6e31000 0 0x8>; clocks = <&cpg CPG_MOD 523>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 523>; #pwm-cells = <2>; status = "disabled"; }; @@ -921,6 +1023,7 @@ reg = <0 0xe6e32000 0 0x8>; clocks = <&cpg CPG_MOD 523>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 523>; #pwm-cells = <2>; status = "disabled"; }; @@ -930,6 +1033,7 @@ reg = <0 0xe6e33000 0 0x8>; clocks = <&cpg CPG_MOD 523>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 523>; #pwm-cells = <2>; status = "disabled"; }; @@ -939,6 +1043,7 @@ reg = <0 0xe6e34000 0 0x8>; clocks = <&cpg CPG_MOD 523>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 523>; #pwm-cells = <2>; status = "disabled"; }; @@ -948,6 +1053,7 @@ reg = <0 0xe6e35000 0 0x8>; clocks = <&cpg CPG_MOD 523>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 523>; #pwm-cells = <2>; status = "disabled"; }; @@ -957,6 +1063,7 @@ reg = <0 0xe6e36000 0 0x8>; clocks = <&cpg CPG_MOD 523>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 523>; #pwm-cells = <2>; status = "disabled"; }; @@ -1015,11 +1122,11 @@ rcar_sound,dvc { dvc0: dvc-0 { - dmas = <&audma0 0xbc>; + dmas = <&audma1 0xbc>; dma-names = "tx"; }; dvc1: dvc-1 { - dmas = <&audma0 0xbe>; + dmas = <&audma1 0xbe>; dma-names = "tx"; }; }; @@ -1149,10 +1256,11 @@ sata: sata@ee300000 { compatible = "renesas,sata-r8a7795"; - reg = <0 0xee300000 0 0x1fff>; + reg = <0 0xee300000 0 0x200000>; interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 815>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 815>; status = "disabled"; }; @@ -1162,6 +1270,7 @@ interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 328>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 328>; status = "disabled"; }; @@ -1171,6 +1280,7 @@ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 327>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 327>; status = "disabled"; }; @@ -1183,6 +1293,7 @@ interrupt-names = "ch0", "ch1"; clocks = <&cpg CPG_MOD 330>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 330>; #dma-cells = <1>; dma-channels = <2>; }; @@ -1196,6 +1307,7 @@ interrupt-names = "ch0", "ch1"; clocks = <&cpg CPG_MOD 331>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 331>; #dma-cells = <1>; dma-channels = <2>; }; @@ -1207,6 +1319,7 @@ clocks = <&cpg CPG_MOD 314>; max-frequency = <200000000>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 314>; status = "disabled"; }; @@ -1217,6 +1330,7 @@ clocks = <&cpg CPG_MOD 313>; max-frequency = <200000000>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 313>; status = "disabled"; }; @@ -1227,6 +1341,7 @@ clocks = <&cpg CPG_MOD 312>; max-frequency = <200000000>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 312>; status = "disabled"; }; @@ -1237,6 +1352,7 @@ clocks = <&cpg CPG_MOD 311>; max-frequency = <200000000>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 311>; status = "disabled"; }; @@ -1247,6 +1363,7 @@ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 703>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 703>; #phy-cells = <0>; status = "disabled"; }; @@ -1257,6 +1374,7 @@ reg = <0 0xee0a0200 0 0x700>; clocks = <&cpg CPG_MOD 702>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 702>; #phy-cells = <0>; status = "disabled"; }; @@ -1267,6 +1385,7 @@ reg = <0 0xee0c0200 0 0x700>; clocks = <&cpg CPG_MOD 701>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 701>; #phy-cells = <0>; status = "disabled"; }; @@ -1279,6 +1398,7 @@ phys = <&usb2_phy0>; phy-names = "usb"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 703>; status = "disabled"; }; @@ -1290,6 +1410,7 @@ phys = <&usb2_phy1>; phy-names = "usb"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 702>; status = "disabled"; }; @@ -1301,6 +1422,7 @@ phys = <&usb2_phy2>; phy-names = "usb"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 701>; status = "disabled"; }; @@ -1312,6 +1434,7 @@ phys = <&usb2_phy0>; phy-names = "usb"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 703>; status = "disabled"; }; @@ -1323,6 +1446,7 @@ phys = <&usb2_phy1>; phy-names = "usb"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 702>; status = "disabled"; }; @@ -1334,6 +1458,7 @@ phys = <&usb2_phy2>; phy-names = "usb"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 701>; status = "disabled"; }; @@ -1350,6 +1475,7 @@ phys = <&usb2_phy0>; phy-names = "usb"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 704>; status = "disabled"; }; @@ -1376,6 +1502,7 @@ clocks = <&cpg CPG_MOD 319>, <&pcie_bus_clk>; clock-names = "pcie", "pcie_bus"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 319>; status = "disabled"; }; @@ -1402,6 +1529,7 @@ clocks = <&cpg CPG_MOD 318>, <&pcie_bus_clk>; clock-names = "pcie", "pcie_bus"; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 318>; status = "disabled"; }; @@ -1411,6 +1539,7 @@ interrupts = <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 624>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 624>; renesas,fcp = <&fcpvb1>; }; @@ -1420,6 +1549,7 @@ reg = <0 0xfe92f000 0 0x200>; clocks = <&cpg CPG_MOD 606>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 606>; }; fcpf0: fcp@fe950000 { @@ -1427,6 +1557,7 @@ reg = <0 0xfe950000 0 0x200>; clocks = <&cpg CPG_MOD 615>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 615>; }; fcpf1: fcp@fe951000 { @@ -1434,6 +1565,7 @@ reg = <0 0xfe951000 0 0x200>; clocks = <&cpg CPG_MOD 614>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 614>; }; fcpf2: fcp@fe952000 { @@ -1441,6 +1573,7 @@ reg = <0 0xfe952000 0 0x200>; clocks = <&cpg CPG_MOD 613>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 613>; }; vspbd: vsp@fe960000 { @@ -1449,6 +1582,7 @@ interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 626>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 626>; renesas,fcp = <&fcpvb0>; }; @@ -1458,6 +1592,7 @@ reg = <0 0xfe96f000 0 0x200>; clocks = <&cpg CPG_MOD 607>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 607>; }; vspi0: vsp@fe9a0000 { @@ -1466,6 +1601,7 @@ interrupts = <GIC_SPI 444 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 631>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 631>; renesas,fcp = <&fcpvi0>; }; @@ -1475,6 +1611,7 @@ reg = <0 0xfe9af000 0 0x200>; clocks = <&cpg CPG_MOD 611>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 611>; }; vspi1: vsp@fe9b0000 { @@ -1483,6 +1620,7 @@ interrupts = <GIC_SPI 445 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 630>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 630>; renesas,fcp = <&fcpvi1>; }; @@ -1492,6 +1630,7 @@ reg = <0 0xfe9bf000 0 0x200>; clocks = <&cpg CPG_MOD 610>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 610>; }; vspi2: vsp@fe9c0000 { @@ -1500,6 +1639,7 @@ interrupts = <GIC_SPI 446 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 629>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 629>; renesas,fcp = <&fcpvi2>; }; @@ -1509,6 +1649,7 @@ reg = <0 0xfe9cf000 0 0x200>; clocks = <&cpg CPG_MOD 609>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 609>; }; vspd0: vsp@fea20000 { @@ -1517,6 +1658,7 @@ interrupts = <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 623>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 623>; renesas,fcp = <&fcpvd0>; }; @@ -1526,6 +1668,7 @@ reg = <0 0xfea27000 0 0x200>; clocks = <&cpg CPG_MOD 603>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 603>; }; vspd1: vsp@fea28000 { @@ -1534,6 +1677,7 @@ interrupts = <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 622>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 622>; renesas,fcp = <&fcpvd1>; }; @@ -1543,6 +1687,7 @@ reg = <0 0xfea2f000 0 0x200>; clocks = <&cpg CPG_MOD 602>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 602>; }; vspd2: vsp@fea30000 { @@ -1551,6 +1696,7 @@ interrupts = <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 621>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 621>; renesas,fcp = <&fcpvd2>; }; @@ -1560,6 +1706,7 @@ reg = <0 0xfea37000 0 0x200>; clocks = <&cpg CPG_MOD 601>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 601>; }; vspd3: vsp@fea38000 { @@ -1568,6 +1715,7 @@ interrupts = <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 620>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 620>; renesas,fcp = <&fcpvd3>; }; @@ -1577,6 +1725,7 @@ reg = <0 0xfea3f000 0 0x200>; clocks = <&cpg CPG_MOD 600>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 600>; }; fdp1@fe940000 { @@ -1585,6 +1734,7 @@ interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 119>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 119>; renesas,fcp = <&fcpf0>; }; @@ -1594,6 +1744,7 @@ interrupts = <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 118>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 118>; renesas,fcp = <&fcpf1>; }; @@ -1603,6 +1754,7 @@ interrupts = <GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 117>; power-domains = <&sysc R8A7795_PD_A3VP>; + resets = <&cpg 117>; renesas,fcp = <&fcpf2>; }; @@ -1662,6 +1814,7 @@ <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 522>; power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 522>; #thermal-sensor-cells = <1>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts index c3f064ac2cb4..372b2a944716 100644 --- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts +++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts @@ -180,7 +180,6 @@ &scif_clk { clock-frequency = <14745600>; - status = "okay"; }; &wdt0 { diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts index c7f40f8f3169..c9f59b6ce33f 100644 --- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts +++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts @@ -18,6 +18,7 @@ aliases { serial0 = &scif2; + serial1 = &scif1; ethernet0 = &avb; }; @@ -113,6 +114,11 @@ function = "avb"; }; + scif1_pins: scif1 { + groups = "scif1_data_a", "scif1_ctrl"; + function = "scif1"; + }; + scif2_pins: scif2 { groups = "scif2_data_a"; function = "scif2"; @@ -172,18 +178,7 @@ status = "okay"; phy0: ethernet-phy@0 { - rxc-skew-ps = <900>; - rxdv-skew-ps = <0>; - rxd0-skew-ps = <0>; - rxd1-skew-ps = <0>; - rxd2-skew-ps = <0>; - rxd3-skew-ps = <0>; - txc-skew-ps = <900>; - txen-skew-ps = <0>; - txd0-skew-ps = <0>; - txd1-skew-ps = <0>; - txd2-skew-ps = <0>; - txd3-skew-ps = <0>; + rxc-skew-ps = <1500>; reg = <0>; interrupt-parent = <&gpio2>; interrupts = <11 IRQ_TYPE_LEVEL_LOW>; @@ -239,6 +234,14 @@ status = "okay"; }; +&scif1 { + pinctrl-0 = <&scif1_pins>; + pinctrl-names = "default"; + + uart-has-rtscts; + status = "okay"; +}; + &scif2 { pinctrl-0 = <&scif2_pins>; pinctrl-names = "default"; @@ -247,7 +250,6 @@ &scif_clk { clock-frequency = <14745600>; - status = "okay"; }; &i2c2 { @@ -261,3 +263,7 @@ timeout-sec = <60>; status = "okay"; }; + +&i2c_dvfs { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi index f7120cdedd0d..2ec1ed5f4991 100644 --- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi @@ -25,10 +25,11 @@ i2c4 = &i2c4; i2c5 = &i2c5; i2c6 = &i2c6; + i2c7 = &i2c_dvfs; }; psci { - compatible = "arm,psci-0.2"; + compatible = "arm,psci-1.0", "arm,psci-0.2"; method = "smc"; }; @@ -36,7 +37,6 @@ #address-cells = <1>; #size-cells = <0>; - /* 1 core only at this point */ a57_0: cpu@0 { compatible = "arm,cortex-a57", "arm,armv8"; reg = <0x0>; @@ -46,13 +46,64 @@ enable-method = "psci"; }; - L2_CA57: cache-controller@0 { + a57_1: cpu@1 { + compatible = "arm,cortex-a57","arm,armv8"; + reg = <0x1>; + device_type = "cpu"; + power-domains = <&sysc R8A7796_PD_CA57_CPU1>; + next-level-cache = <&L2_CA57>; + enable-method = "psci"; + }; + + a53_0: cpu@100 { + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x100>; + device_type = "cpu"; + power-domains = <&sysc R8A7796_PD_CA53_CPU0>; + next-level-cache = <&L2_CA53>; + enable-method = "psci"; + }; + + a53_1: cpu@101 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x101>; + device_type = "cpu"; + power-domains = <&sysc R8A7796_PD_CA53_CPU1>; + next-level-cache = <&L2_CA53>; + enable-method = "psci"; + }; + + a53_2: cpu@102 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x102>; + device_type = "cpu"; + power-domains = <&sysc R8A7796_PD_CA53_CPU2>; + next-level-cache = <&L2_CA53>; + enable-method = "psci"; + }; + + a53_3: cpu@103 { + compatible = "arm,cortex-a53","arm,armv8"; + reg = <0x103>; + device_type = "cpu"; + power-domains = <&sysc R8A7796_PD_CA53_CPU3>; + next-level-cache = <&L2_CA53>; + enable-method = "psci"; + }; + + L2_CA57: cache-controller-0 { compatible = "cache"; - reg = <0>; power-domains = <&sysc R8A7796_PD_CA57_SCU>; cache-unified; cache-level = <2>; }; + + L2_CA53: cache-controller-1 { + compatible = "cache"; + power-domains = <&sysc R8A7796_PD_CA53_SCU>; + cache-unified; + cache-level = <2>; + }; }; extal_clk: extal { @@ -100,22 +151,23 @@ <0x0 0xf1040000 0 0x20000>, <0x0 0xf1060000 0 0x20000>; interrupts = <GIC_PPI 9 - (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>; + (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_HIGH)>; clocks = <&cpg CPG_MOD 408>; clock-names = "clk"; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 408>; }; timer { compatible = "arm,armv8-timer"; interrupts = <GIC_PPI 13 - (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>, + (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 14 - (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>, + (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 11 - (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>, + (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 10 - (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>; + (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>; }; wdt0: watchdog@e6020000 { @@ -124,6 +176,7 @@ reg = <0 0xe6020000 0 0x0c>; clocks = <&cpg CPG_MOD 402>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 402>; status = "disabled"; }; @@ -139,6 +192,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 912>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 912>; }; gpio1: gpio@e6051000 { @@ -153,6 +207,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 911>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 911>; }; gpio2: gpio@e6052000 { @@ -167,6 +222,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 910>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 910>; }; gpio3: gpio@e6053000 { @@ -181,6 +237,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 909>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 909>; }; gpio4: gpio@e6054000 { @@ -195,6 +252,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 908>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 908>; }; gpio5: gpio@e6055000 { @@ -209,6 +267,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 907>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 907>; }; gpio6: gpio@e6055400 { @@ -223,6 +282,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 906>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 906>; }; gpio7: gpio@e6055800 { @@ -237,6 +297,7 @@ interrupt-controller; clocks = <&cpg CPG_MOD 905>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 905>; }; pfc: pin-controller@e6060000 { @@ -244,6 +305,26 @@ reg = <0 0xe6060000 0 0x50c>; }; + pmu_a57 { + compatible = "arm,cortex-a57-pmu"; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&a57_0>, + <&a57_1>; + }; + + pmu_a53 { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&a53_0>, + <&a53_1>, + <&a53_2>, + <&a53_3>; + }; + cpg: clock-controller@e6150000 { compatible = "renesas,r8a7796-cpg-mssr"; reg = <0 0xe6150000 0 0x1000>; @@ -251,6 +332,7 @@ clock-names = "extal", "extalr"; #clock-cells = <2>; #power-domain-cells = <0>; + #reset-cells = <1>; }; rst: reset-controller@e6160000 { @@ -269,6 +351,20 @@ #power-domain-cells = <1>; }; + i2c_dvfs: i2c@e60b0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,iic-r8a7796", + "renesas,rcar-gen3-iic", + "renesas,rmobile-iic"; + reg = <0 0xe60b0000 0 0x425>; + interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 926>; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 926>; + status = "disabled"; + }; + i2c0: i2c@e6500000 { #address-cells = <1>; #size-cells = <0>; @@ -278,6 +374,7 @@ interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 931>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 931>; dmas = <&dmac1 0x91>, <&dmac1 0x90>, <&dmac2 0x91>, <&dmac2 0x90>; dma-names = "tx", "rx", "tx", "rx"; @@ -294,6 +391,7 @@ interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 930>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 930>; dmas = <&dmac1 0x93>, <&dmac1 0x92>, <&dmac2 0x93>, <&dmac2 0x92>; dma-names = "tx", "rx", "tx", "rx"; @@ -310,6 +408,7 @@ interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 929>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 929>; dmas = <&dmac1 0x95>, <&dmac1 0x94>, <&dmac2 0x95>, <&dmac2 0x94>; dma-names = "tx", "rx", "tx", "rx"; @@ -326,6 +425,7 @@ interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 928>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 928>; dmas = <&dmac0 0x97>, <&dmac0 0x96>; dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <110>; @@ -341,6 +441,7 @@ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 927>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 927>; dmas = <&dmac0 0x99>, <&dmac0 0x98>; dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <110>; @@ -356,6 +457,7 @@ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 919>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 919>; dmas = <&dmac0 0x9b>, <&dmac0 0x9a>; dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <110>; @@ -371,6 +473,7 @@ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 918>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 918>; dmas = <&dmac0 0x9d>, <&dmac0 0x9c>; dma-names = "tx", "rx"; i2c-scl-internal-delay-ns = <6>; @@ -389,6 +492,7 @@ assigned-clocks = <&cpg CPG_CORE R8A7796_CLK_CANFD>; assigned-clock-rates = <40000000>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 916>; status = "disabled"; }; @@ -404,6 +508,7 @@ assigned-clocks = <&cpg CPG_CORE R8A7796_CLK_CANFD>; assigned-clock-rates = <40000000>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 915>; status = "disabled"; }; @@ -420,6 +525,7 @@ assigned-clocks = <&cpg CPG_CORE R8A7796_CLK_CANFD>; assigned-clock-rates = <40000000>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 914>; status = "disabled"; channel0 { @@ -469,12 +575,135 @@ "ch24"; clocks = <&cpg CPG_MOD 812>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; - phy-mode = "rgmii-id"; + resets = <&cpg 812>; + phy-mode = "rgmii-txid"; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; + hscif0: serial@e6540000 { + compatible = "renesas,hscif-r8a7796", + "renesas,rcar-gen3-hscif", + "renesas,hscif"; + reg = <0 0xe6540000 0 0x60>; + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 520>, + <&cpg CPG_CORE R8A7796_CLK_S3D1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x31>, <&dmac1 0x30>, + <&dmac2 0x31>, <&dmac2 0x30>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 520>; + status = "disabled"; + }; + + hscif1: serial@e6550000 { + compatible = "renesas,hscif-r8a7796", + "renesas,rcar-gen3-hscif", + "renesas,hscif"; + reg = <0 0xe6550000 0 0x60>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 519>, + <&cpg CPG_CORE R8A7796_CLK_S3D1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x33>, <&dmac1 0x32>, + <&dmac2 0x33>, <&dmac2 0x32>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 519>; + status = "disabled"; + }; + + hscif2: serial@e6560000 { + compatible = "renesas,hscif-r8a7796", + "renesas,rcar-gen3-hscif", + "renesas,hscif"; + reg = <0 0xe6560000 0 0x60>; + interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 518>, + <&cpg CPG_CORE R8A7796_CLK_S3D1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x35>, <&dmac1 0x34>, + <&dmac2 0x35>, <&dmac2 0x34>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 518>; + status = "disabled"; + }; + + hscif3: serial@e66a0000 { + compatible = "renesas,hscif-r8a7796", + "renesas,rcar-gen3-hscif", + "renesas,hscif"; + reg = <0 0xe66a0000 0 0x60>; + interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 517>, + <&cpg CPG_CORE R8A7796_CLK_S3D1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x37>, <&dmac0 0x36>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 517>; + status = "disabled"; + }; + + hscif4: serial@e66b0000 { + compatible = "renesas,hscif-r8a7796", + "renesas,rcar-gen3-hscif", + "renesas,hscif"; + reg = <0 0xe66b0000 0 0x60>; + interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 516>, + <&cpg CPG_CORE R8A7796_CLK_S3D1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x39>, <&dmac0 0x38>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 516>; + status = "disabled"; + }; + + scif0: serial@e6e60000 { + compatible = "renesas,scif-r8a7796", + "renesas,rcar-gen3-scif", "renesas,scif"; + reg = <0 0xe6e60000 0 64>; + interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 207>, + <&cpg CPG_CORE R8A7796_CLK_S3D1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x51>, <&dmac1 0x50>, + <&dmac2 0x51>, <&dmac2 0x50>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 207>; + status = "disabled"; + }; + + scif1: serial@e6e68000 { + compatible = "renesas,scif-r8a7796", + "renesas,rcar-gen3-scif", "renesas,scif"; + reg = <0 0xe6e68000 0 64>; + interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 206>, + <&cpg CPG_CORE R8A7796_CLK_S3D1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x53>, <&dmac1 0x52>, + <&dmac2 0x53>, <&dmac2 0x52>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 206>; + status = "disabled"; + }; + scif2: serial@e6e88000 { compatible = "renesas,scif-r8a7796", "renesas,rcar-gen3-scif", "renesas,scif"; @@ -485,6 +714,56 @@ <&scif_clk>; clock-names = "fck", "brg_int", "scif_clk"; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 310>; + status = "disabled"; + }; + + scif3: serial@e6c50000 { + compatible = "renesas,scif-r8a7796", + "renesas,rcar-gen3-scif", "renesas,scif"; + reg = <0 0xe6c50000 0 64>; + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 204>, + <&cpg CPG_CORE R8A7796_CLK_S3D1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x57>, <&dmac0 0x56>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 204>; + status = "disabled"; + }; + + scif4: serial@e6c40000 { + compatible = "renesas,scif-r8a7796", + "renesas,rcar-gen3-scif", "renesas,scif"; + reg = <0 0xe6c40000 0 64>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 203>, + <&cpg CPG_CORE R8A7796_CLK_S3D1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x59>, <&dmac0 0x58>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 203>; + status = "disabled"; + }; + + scif5: serial@e6f30000 { + compatible = "renesas,scif-r8a7796", + "renesas,rcar-gen3-scif", "renesas,scif"; + reg = <0 0xe6f30000 0 64>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 202>, + <&cpg CPG_CORE R8A7796_CLK_S3D1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x5b>, <&dmac1 0x5a>, + <&dmac2 0x5b>, <&dmac2 0x5a>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 202>; status = "disabled"; }; @@ -498,6 +777,7 @@ <&dmac2 0x41>, <&dmac2 0x40>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 211>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -513,6 +793,7 @@ <&dmac2 0x43>, <&dmac2 0x42>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 210>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -527,6 +808,7 @@ dmas = <&dmac0 0x45>, <&dmac0 0x44>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 209>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -541,6 +823,7 @@ dmas = <&dmac0 0x47>, <&dmac0 0x46>; dma-names = "tx", "rx"; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 208>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -575,6 +858,7 @@ clocks = <&cpg CPG_MOD 219>; clock-names = "fck"; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 219>; #dma-cells = <1>; dma-channels = <16>; }; @@ -608,6 +892,7 @@ clocks = <&cpg CPG_MOD 218>; clock-names = "fck"; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 218>; #dma-cells = <1>; dma-channels = <16>; }; @@ -641,6 +926,7 @@ clocks = <&cpg CPG_MOD 217>; clock-names = "fck"; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 217>; #dma-cells = <1>; dma-channels = <16>; }; @@ -652,6 +938,7 @@ clocks = <&cpg CPG_MOD 314>; max-frequency = <200000000>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 314>; status = "disabled"; }; @@ -662,6 +949,7 @@ clocks = <&cpg CPG_MOD 313>; max-frequency = <200000000>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 313>; status = "disabled"; }; @@ -672,6 +960,7 @@ clocks = <&cpg CPG_MOD 312>; max-frequency = <200000000>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 312>; status = "disabled"; }; @@ -682,6 +971,7 @@ clocks = <&cpg CPG_MOD 311>; max-frequency = <200000000>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 311>; status = "disabled"; }; @@ -695,6 +985,7 @@ <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 522>; power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 522>; #thermal-sensor-cells = <1>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile index 3a862894ea44..b5636bba6b1c 100644 --- a/arch/arm64/boot/dts/rockchip/Makefile +++ b/arch/arm64/boot/dts/rockchip/Makefile @@ -1,9 +1,11 @@ +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-px5-evb.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-kevin.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/rockchip/rk3328-evb.dts b/arch/arm64/boot/dts/rockchip/rk3328-evb.dts new file mode 100644 index 000000000000..cf272392cebf --- /dev/null +++ b/arch/arm64/boot/dts/rockchip/rk3328-evb.dts @@ -0,0 +1,57 @@ +/* + * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "rk3328.dtsi" + +/ { + model = "Rockchip RK3328 EVB"; + compatible = "rockchip,rk3328-evb", "rockchip,rk3328"; + + chosen { + stdout-path = "serial2:1500000n8"; + }; +}; + +&uart2 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi new file mode 100644 index 000000000000..7e69f1fe78d6 --- /dev/null +++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi @@ -0,0 +1,1264 @@ +/* + * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/clock/rk3328-cru.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/power/rk3328-power.h> +#include <dt-bindings/soc/rockchip,boot-mode.h> + +/ { + compatible = "rockchip,rk3328"; + + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x0>; + clocks = <&cru ARMCLK>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x1>; + clocks = <&cru ARMCLK>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x2>; + clocks = <&cru ARMCLK>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x3>; + clocks = <&cru ARMCLK>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; + + l2: l2-cache0 { + compatible = "cache"; + }; + }; + + amba { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + dmac: dmac@ff1f0000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff1f0000 0x0 0x4000>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru ACLK_DMAC>; + clock-names = "apb_pclk"; + #dma-cells = <1>; + }; + }; + + arm-pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; + }; + + psci { + compatible = "arm,psci-1.0", "arm,psci-0.2"; + method = "smc"; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; + + xin24m: xin24m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + clock-output-names = "xin24m"; + }; + + grf: syscon@ff100000 { + compatible = "rockchip,rk3328-grf", "syscon", "simple-mfd"; + reg = <0x0 0xff100000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + power: power-controller { + compatible = "rockchip,rk3328-power-controller"; + #power-domain-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + pd_hevc@RK3328_PD_HEVC { + reg = <RK3328_PD_HEVC>; + }; + pd_video@RK3328_PD_VIDEO { + reg = <RK3328_PD_VIDEO>; + }; + pd_vpu@RK3328_PD_VPU { + reg = <RK3328_PD_VPU>; + }; + }; + + reboot-mode { + compatible = "syscon-reboot-mode"; + offset = <0x5c8>; + mode-normal = <BOOT_NORMAL>; + mode-recovery = <BOOT_RECOVERY>; + mode-bootloader = <BOOT_FASTBOOT>; + mode-loader = <BOOT_BL_DOWNLOAD>; + }; + + }; + + uart0: serial@ff110000 { + compatible = "rockchip,rk3328-uart", "snps,dw-apb-uart"; + reg = <0x0 0xff110000 0x0 0x100>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; + clock-names = "baudclk", "apb_pclk"; + dmas = <&dmac 2>, <&dmac 3>; + #dma-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>; + reg-io-width = <4>; + reg-shift = <2>; + status = "disabled"; + }; + + uart1: serial@ff120000 { + compatible = "rockchip,rk3328-uart", "snps,dw-apb-uart"; + reg = <0x0 0xff120000 0x0 0x100>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>; + clock-names = "sclk_uart", "pclk_uart"; + dmas = <&dmac 4>, <&dmac 5>; + #dma-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&uart1_xfer &uart1_cts &uart1_rts>; + reg-io-width = <4>; + reg-shift = <2>; + status = "disabled"; + }; + + uart2: serial@ff130000 { + compatible = "rockchip,rk3328-uart", "snps,dw-apb-uart"; + reg = <0x0 0xff130000 0x0 0x100>; + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>; + clock-names = "baudclk", "apb_pclk"; + dmas = <&dmac 6>, <&dmac 7>; + #dma-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&uart2m1_xfer>; + reg-io-width = <4>; + reg-shift = <2>; + status = "disabled"; + }; + + i2c0: i2c@ff150000 { + compatible = "rockchip,rk3328-i2c", "rockchip,rk3399-i2c"; + reg = <0x0 0xff150000 0x0 0x1000>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&cru SCLK_I2C0>, <&cru PCLK_I2C0>; + clock-names = "i2c", "pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_xfer>; + status = "disabled"; + }; + + i2c1: i2c@ff160000 { + compatible = "rockchip,rk3328-i2c", "rockchip,rk3399-i2c"; + reg = <0x0 0xff160000 0x0 0x1000>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&cru SCLK_I2C1>, <&cru PCLK_I2C1>; + clock-names = "i2c", "pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_xfer>; + status = "disabled"; + }; + + i2c2: i2c@ff170000 { + compatible = "rockchip,rk3328-i2c", "rockchip,rk3399-i2c"; + reg = <0x0 0xff170000 0x0 0x1000>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&cru SCLK_I2C2>, <&cru PCLK_I2C2>; + clock-names = "i2c", "pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_xfer>; + status = "disabled"; + }; + + i2c3: i2c@ff180000 { + compatible = "rockchip,rk3328-i2c", "rockchip,rk3399-i2c"; + reg = <0x0 0xff180000 0x0 0x1000>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&cru SCLK_I2C3>, <&cru PCLK_I2C3>; + clock-names = "i2c", "pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_xfer>; + status = "disabled"; + }; + + spi0: spi@ff190000 { + compatible = "rockchip,rk3328-spi", "rockchip,rk3066-spi"; + reg = <0x0 0xff190000 0x0 0x1000>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&cru SCLK_SPI>, <&cru PCLK_SPI>; + clock-names = "spiclk", "apb_pclk"; + dmas = <&dmac 8>, <&dmac 9>; + dma-names = "tx", "rx"; + pinctrl-names = "default"; + pinctrl-0 = <&spi0m2_clk &spi0m2_tx &spi0m2_rx &spi0m2_cs0>; + status = "disabled"; + }; + + wdt: watchdog@ff1a0000 { + compatible = "snps,dw-wdt"; + reg = <0x0 0xff1a0000 0x0 0x100>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + }; + + saradc: adc@ff280000 { + compatible = "rockchip,rk3328-saradc", "rockchip,rk3399-saradc"; + reg = <0x0 0xff280000 0x0 0x100>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; + #io-channel-cells = <1>; + clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>; + clock-names = "saradc", "apb_pclk"; + resets = <&cru SRST_SARADC_P>; + reset-names = "saradc-apb"; + status = "disabled"; + }; + + cru: clock-controller@ff440000 { + compatible = "rockchip,rk3328-cru", "rockchip,cru", "syscon"; + reg = <0x0 0xff440000 0x0 0x1000>; + rockchip,grf = <&grf>; + #clock-cells = <1>; + #reset-cells = <1>; + assigned-clocks = + /* + * CPLL should run at 1200, but that is to high for + * the initial dividers of most of its children. + * We need set cpll child clk div first, + * and then set the cpll frequency. + */ + <&cru DCLK_LCDC>, <&cru SCLK_PDM>, + <&cru SCLK_RTC32K>, <&cru SCLK_UART0>, + <&cru SCLK_UART1>, <&cru SCLK_UART2>, + <&cru ACLK_BUS_PRE>, <&cru ACLK_PERI_PRE>, + <&cru ACLK_VIO_PRE>, <&cru ACLK_RGA_PRE>, + <&cru ACLK_VOP_PRE>, <&cru ACLK_RKVDEC_PRE>, + <&cru ACLK_RKVENC>, <&cru ACLK_VPU_PRE>, + <&cru SCLK_VDEC_CABAC>, <&cru SCLK_VDEC_CORE>, + <&cru SCLK_VENC_CORE>, <&cru SCLK_VENC_DSP>, + <&cru SCLK_SDIO>, <&cru SCLK_TSP>, + <&cru SCLK_WIFI>, <&cru ARMCLK>, + <&cru PLL_GPLL>, <&cru PLL_CPLL>, + <&cru ACLK_BUS_PRE>, <&cru HCLK_BUS_PRE>, + <&cru PCLK_BUS_PRE>, <&cru ACLK_PERI_PRE>, + <&cru HCLK_PERI>, <&cru PCLK_PERI>, + <&cru SCLK_RTC32K>; + assigned-clock-parents = + <&cru HDMIPHY>, <&cru PLL_APLL>, + <&cru PLL_GPLL>, <&xin24m>, + <&xin24m>, <&xin24m>; + assigned-clock-rates = + <0>, <61440000>, + <0>, <24000000>, + <24000000>, <24000000>, + <15000000>, <15000000>, + <100000000>, <100000000>, + <100000000>, <100000000>, + <50000000>, <100000000>, + <100000000>, <100000000>, + <50000000>, <50000000>, + <50000000>, <50000000>, + <24000000>, <600000000>, + <491520000>, <1200000000>, + <150000000>, <75000000>, + <75000000>, <150000000>, + <75000000>, <75000000>, + <32768>; + }; + + gmac2io: ethernet@ff540000 { + compatible = "rockchip,rk3328-gmac"; + reg = <0x0 0xff540000 0x0 0x10000>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_RX>, + <&cru SCLK_MAC2IO_TX>, <&cru SCLK_MAC2IO_REF>, + <&cru SCLK_MAC2IO_REFOUT>, <&cru ACLK_MAC2IO>, + <&cru PCLK_MAC2IO>; + clock-names = "stmmaceth", "mac_clk_rx", + "mac_clk_tx", "clk_mac_ref", + "clk_mac_refout", "aclk_mac", + "pclk_mac"; + resets = <&cru SRST_GMAC2IO_A>; + reset-names = "stmmaceth"; + rockchip,grf = <&grf>; + status = "disabled"; + }; + + gic: interrupt-controller@ff811000 { + compatible = "arm,gic-400"; + #interrupt-cells = <3>; + #address-cells = <0>; + interrupt-controller; + reg = <0x0 0xff811000 0 0x1000>, + <0x0 0xff812000 0 0x2000>, + <0x0 0xff814000 0 0x2000>, + <0x0 0xff816000 0 0x2000>; + interrupts = <GIC_PPI 9 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + }; + + pinctrl: pinctrl { + compatible = "rockchip,rk3328-pinctrl"; + rockchip,grf = <&grf>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + gpio0: gpio0@ff210000 { + compatible = "rockchip,gpio-bank"; + reg = <0x0 0xff210000 0x0 0x100>; + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru PCLK_GPIO0>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio1@ff220000 { + compatible = "rockchip,gpio-bank"; + reg = <0x0 0xff220000 0x0 0x100>; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru PCLK_GPIO1>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio2@ff230000 { + compatible = "rockchip,gpio-bank"; + reg = <0x0 0xff230000 0x0 0x100>; + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru PCLK_GPIO2>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio3@ff240000 { + compatible = "rockchip,gpio-bank"; + reg = <0x0 0xff240000 0x0 0x100>; + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru PCLK_GPIO3>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + pcfg_pull_up: pcfg-pull-up { + bias-pull-up; + }; + + pcfg_pull_down: pcfg-pull-down { + bias-pull-down; + }; + + pcfg_pull_none: pcfg-pull-none { + bias-disable; + }; + + pcfg_pull_none_2ma: pcfg-pull-none-2ma { + bias-disable; + drive-strength = <2>; + }; + + pcfg_pull_up_2ma: pcfg-pull-up-2ma { + bias-pull-up; + drive-strength = <2>; + }; + + pcfg_pull_up_4ma: pcfg-pull-up-4ma { + bias-pull-up; + drive-strength = <4>; + }; + + pcfg_pull_none_4ma: pcfg-pull-none-4ma { + bias-disable; + drive-strength = <4>; + }; + + pcfg_pull_down_4ma: pcfg-pull-down-4ma { + bias-pull-down; + drive-strength = <4>; + }; + + pcfg_pull_none_8ma: pcfg-pull-none-8ma { + bias-disable; + drive-strength = <8>; + }; + + pcfg_pull_up_8ma: pcfg-pull-up-8ma { + bias-pull-up; + drive-strength = <8>; + }; + + pcfg_pull_none_12ma: pcfg-pull-none-12ma { + bias-disable; + drive-strength = <12>; + }; + + pcfg_pull_up_12ma: pcfg-pull-up-12ma { + bias-pull-up; + drive-strength = <12>; + }; + + pcfg_output_high: pcfg-output-high { + output-high; + }; + + pcfg_output_low: pcfg-output-low { + output-low; + }; + + pcfg_input_high: pcfg-input-high { + bias-pull-up; + input-enable; + }; + + pcfg_input: pcfg-input { + input-enable; + }; + + i2c0 { + i2c0_xfer: i2c0-xfer { + rockchip,pins = <2 RK_PD0 1 &pcfg_pull_none>, + <2 RK_PD1 1 &pcfg_pull_none>; + }; + }; + + i2c1 { + i2c1_xfer: i2c1-xfer { + rockchip,pins = <2 RK_PA4 2 &pcfg_pull_none>, + <2 RK_PA5 2 &pcfg_pull_none>; + }; + }; + + i2c2 { + i2c2_xfer: i2c2-xfer { + rockchip,pins = <2 RK_PB5 1 &pcfg_pull_none>, + <2 RK_PB6 1 &pcfg_pull_none>; + }; + }; + + i2c3 { + i2c3_xfer: i2c3-xfer { + rockchip,pins = <0 RK_PA5 2 &pcfg_pull_none>, + <0 RK_PA6 2 &pcfg_pull_none>; + }; + i2c3_gpio: i2c3-gpio { + rockchip,pins = + <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>, + <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + hdmi_i2c { + hdmii2c_xfer: hdmii2c-xfer { + rockchip,pins = <0 RK_PA5 1 &pcfg_pull_none>, + <0 RK_PA6 1 &pcfg_pull_none>; + }; + }; + + tsadc { + otp_gpio: otp-gpio { + rockchip,pins = <2 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + otp_out: otp-out { + rockchip,pins = <2 RK_PB5 1 &pcfg_pull_none>; + }; + }; + + uart0 { + uart0_xfer: uart0-xfer { + rockchip,pins = <1 RK_PB1 1 &pcfg_pull_up>, + <1 RK_PB0 1 &pcfg_pull_none>; + }; + + uart0_cts: uart0-cts { + rockchip,pins = <1 RK_PB3 1 &pcfg_pull_none>; + }; + + uart0_rts: uart0-rts { + rockchip,pins = <1 RK_PB2 1 &pcfg_pull_none>; + }; + + uart0_rts_gpio: uart0-rts-gpio { + rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + uart1 { + uart1_xfer: uart1-xfer { + rockchip,pins = <3 RK_PA4 4 &pcfg_pull_up>, + <3 RK_PA6 4 &pcfg_pull_none>; + }; + + uart1_cts: uart1-cts { + rockchip,pins = <3 RK_PA7 4 &pcfg_pull_none>; + }; + + uart1_rts: uart1-rts { + rockchip,pins = <3 RK_PA5 4 &pcfg_pull_none>; + }; + + uart1_rts_gpio: uart1-rts-gpio { + rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + uart2-0 { + uart2m0_xfer: uart2m0-xfer { + rockchip,pins = <1 RK_PA0 2 &pcfg_pull_up>, + <1 RK_PA1 2 &pcfg_pull_none>; + }; + }; + + uart2-1 { + uart2m1_xfer: uart2m1-xfer { + rockchip,pins = <2 RK_PA0 1 &pcfg_pull_up>, + <2 RK_PA1 1 &pcfg_pull_none>; + }; + }; + + spi0-0 { + spi0m0_clk: spi0m0-clk { + rockchip,pins = <2 RK_PB0 1 &pcfg_pull_up>; + }; + + spi0m0_cs0: spi0m0-cs0 { + rockchip,pins = <2 RK_PB3 1 &pcfg_pull_up>; + }; + + spi0m0_tx: spi0m0-tx { + rockchip,pins = <2 RK_PB1 1 &pcfg_pull_up>; + }; + + spi0m0_rx: spi0m0-rx { + rockchip,pins = <2 RK_PB2 1 &pcfg_pull_up>; + }; + + spi0m0_cs1: spi0m0-cs1 { + rockchip,pins = <2 RK_PB4 1 &pcfg_pull_up>; + }; + }; + + spi0-1 { + spi0m1_clk: spi0m1-clk { + rockchip,pins = <3 RK_PC7 2 &pcfg_pull_up>; + }; + + spi0m1_cs0: spi0m1-cs0 { + rockchip,pins = <3 RK_PD2 2 &pcfg_pull_up>; + }; + + spi0m1_tx: spi0m1-tx { + rockchip,pins = <3 RK_PD1 2 &pcfg_pull_up>; + }; + + spi0m1_rx: spi0m1-rx { + rockchip,pins = <3 RK_PD0 2 &pcfg_pull_up>; + }; + + spi0m1_cs1: spi0m1-cs1 { + rockchip,pins = <3 RK_PD3 2 &pcfg_pull_up>; + }; + }; + + spi0-2 { + spi0m2_clk: spi0m2-clk { + rockchip,pins = <3 RK_PA0 4 &pcfg_pull_up>; + }; + + spi0m2_cs0: spi0m2-cs0 { + rockchip,pins = <3 RK_PB0 3 &pcfg_pull_up>; + }; + + spi0m2_tx: spi0m2-tx { + rockchip,pins = <3 RK_PA1 4 &pcfg_pull_up>; + }; + + spi0m2_rx: spi0m2-rx { + rockchip,pins = <3 RK_PA2 4 &pcfg_pull_up>; + }; + }; + + i2s1 { + i2s1_mclk: i2s1-mclk { + rockchip,pins = <2 RK_PB7 1 &pcfg_pull_none>; + }; + + i2s1_sclk: i2s1-sclk { + rockchip,pins = <2 RK_PC2 1 &pcfg_pull_none>; + }; + + i2s1_lrckrx: i2s1-lrckrx { + rockchip,pins = <2 RK_PC0 1 &pcfg_pull_none>; + }; + + i2s1_lrcktx: i2s1-lrcktx { + rockchip,pins = <2 RK_PC1 1 &pcfg_pull_none>; + }; + + i2s1_sdi: i2s1-sdi { + rockchip,pins = <2 RK_PC3 1 &pcfg_pull_none>; + }; + + i2s1_sdo: i2s1-sdo { + rockchip,pins = <2 RK_PC7 1 &pcfg_pull_none>; + }; + + i2s1_sdio1: i2s1-sdio1 { + rockchip,pins = <2 RK_PC4 1 &pcfg_pull_none>; + }; + + i2s1_sdio2: i2s1-sdio2 { + rockchip,pins = <2 RK_PC5 1 &pcfg_pull_none>; + }; + + i2s1_sdio3: i2s1-sdio3 { + rockchip,pins = <2 RK_PC6 1 &pcfg_pull_none>; + }; + + i2s1_sleep: i2s1-sleep { + rockchip,pins = + <2 RK_PB7 RK_FUNC_GPIO &pcfg_input_high>, + <2 RK_PC0 RK_FUNC_GPIO &pcfg_input_high>, + <2 RK_PC1 RK_FUNC_GPIO &pcfg_input_high>, + <2 RK_PC2 RK_FUNC_GPIO &pcfg_input_high>, + <2 RK_PC3 RK_FUNC_GPIO &pcfg_input_high>, + <2 RK_PC4 RK_FUNC_GPIO &pcfg_input_high>, + <2 RK_PC5 RK_FUNC_GPIO &pcfg_input_high>, + <2 RK_PC6 RK_FUNC_GPIO &pcfg_input_high>, + <2 RK_PC7 RK_FUNC_GPIO &pcfg_input_high>; + }; + }; + + i2s2-0 { + i2s2m0_mclk: i2s2m0-mclk { + rockchip,pins = <1 RK_PC5 1 &pcfg_pull_none>; + }; + + i2s2m0_sclk: i2s2m0-sclk { + rockchip,pins = <1 RK_PC6 1 &pcfg_pull_none>; + }; + + i2s2m0_lrckrx: i2s2m0-lrckrx { + rockchip,pins = <1 RK_PD2 1 &pcfg_pull_none>; + }; + + i2s2m0_lrcktx: i2s2m0-lrcktx { + rockchip,pins = <1 RK_PC7 1 &pcfg_pull_none>; + }; + + i2s2m0_sdi: i2s2m0-sdi { + rockchip,pins = <1 RK_PD0 1 &pcfg_pull_none>; + }; + + i2s2m0_sdo: i2s2m0-sdo { + rockchip,pins = <1 RK_PD1 1 &pcfg_pull_none>; + }; + + i2s2m0_sleep: i2s2m0-sleep { + rockchip,pins = + <1 RK_PC5 RK_FUNC_GPIO &pcfg_input_high>, + <1 RK_PC6 RK_FUNC_GPIO &pcfg_input_high>, + <1 RK_PD2 RK_FUNC_GPIO &pcfg_input_high>, + <1 RK_PC7 RK_FUNC_GPIO &pcfg_input_high>, + <1 RK_PD0 RK_FUNC_GPIO &pcfg_input_high>, + <1 RK_PD1 RK_FUNC_GPIO &pcfg_input_high>; + }; + }; + + i2s2-1 { + i2s2m1_mclk: i2s2m1-mclk { + rockchip,pins = <1 RK_PC5 1 &pcfg_pull_none>; + }; + + i2s2m1_sclk: i2s2m1-sclk { + rockchip,pins = <3 RK_PA0 6 &pcfg_pull_none>; + }; + + i2s2m1_lrckrx: i2sm1-lrckrx { + rockchip,pins = <3 RK_PB0 6 &pcfg_pull_none>; + }; + + i2s2m1_lrcktx: i2s2m1-lrcktx { + rockchip,pins = <3 RK_PB0 4 &pcfg_pull_none>; + }; + + i2s2m1_sdi: i2s2m1-sdi { + rockchip,pins = <3 RK_PA2 6 &pcfg_pull_none>; + }; + + i2s2m1_sdo: i2s2m1-sdo { + rockchip,pins = <3 RK_PA1 6 &pcfg_pull_none>; + }; + + i2s2m1_sleep: i2s2m1-sleep { + rockchip,pins = + <1 RK_PC5 RK_FUNC_GPIO &pcfg_input_high>, + <3 RK_PA0 RK_FUNC_GPIO &pcfg_input_high>, + <3 RK_PB0 RK_FUNC_GPIO &pcfg_input_high>, + <3 RK_PA2 RK_FUNC_GPIO &pcfg_input_high>, + <3 RK_PA1 RK_FUNC_GPIO &pcfg_input_high>; + }; + }; + + spdif-0 { + spdifm0_tx: spdifm0-tx { + rockchip,pins = <0 RK_PD3 1 &pcfg_pull_none>; + }; + }; + + spdif-1 { + spdifm1_tx: spdifm1-tx { + rockchip,pins = <2 RK_PC1 2 &pcfg_pull_none>; + }; + }; + + spdif-2 { + spdifm2_tx: spdifm2-tx { + rockchip,pins = <0 RK_PA2 2 &pcfg_pull_none>; + }; + }; + + sdmmc0-0 { + sdmmc0m0_pwren: sdmmc0m0-pwren { + rockchip,pins = <2 RK_PA7 1 &pcfg_pull_up_4ma>; + }; + + sdmmc0m0_gpio: sdmmc0m0-gpio { + rockchip,pins = <2 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up_4ma>; + }; + }; + + sdmmc0-1 { + sdmmc0m1_pwren: sdmmc0m1-pwren { + rockchip,pins = <0 RK_PD6 3 &pcfg_pull_up_4ma>; + }; + + sdmmc0m1_gpio: sdmmc0m1-gpio { + rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up_4ma>; + }; + }; + + sdmmc0 { + sdmmc0_clk: sdmmc0-clk { + rockchip,pins = <1 RK_PA6 1 &pcfg_pull_none_4ma>; + }; + + sdmmc0_cmd: sdmmc0-cmd { + rockchip,pins = <1 RK_PA4 1 &pcfg_pull_up_4ma>; + }; + + sdmmc0_dectn: sdmmc0-dectn { + rockchip,pins = <1 RK_PA5 1 &pcfg_pull_up_4ma>; + }; + + sdmmc0_wrprt: sdmmc0-wrprt { + rockchip,pins = <1 RK_PA7 1 &pcfg_pull_up_4ma>; + }; + + sdmmc0_bus1: sdmmc0-bus1 { + rockchip,pins = <1 RK_PA0 1 &pcfg_pull_up_4ma>; + }; + + sdmmc0_bus4: sdmmc0-bus4 { + rockchip,pins = <1 RK_PA0 1 &pcfg_pull_up_4ma>, + <1 RK_PA1 1 &pcfg_pull_up_4ma>, + <1 RK_PA2 1 &pcfg_pull_up_4ma>, + <1 RK_PA3 1 &pcfg_pull_up_4ma>; + }; + + sdmmc0_gpio: sdmmc0-gpio { + rockchip,pins = + <1 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up_4ma>; + }; + }; + + sdmmc0ext { + sdmmc0ext_clk: sdmmc0ext-clk { + rockchip,pins = <3 RK_PA2 3 &pcfg_pull_none_4ma>; + }; + + sdmmc0ext_cmd: sdmmc0ext-cmd { + rockchip,pins = <3 RK_PA0 3 &pcfg_pull_up_4ma>; + }; + + sdmmc0ext_wrprt: sdmmc0ext-wrprt { + rockchip,pins = <3 RK_PA3 3 &pcfg_pull_up_4ma>; + }; + + sdmmc0ext_dectn: sdmmc0ext-dectn { + rockchip,pins = <3 RK_PA1 3 &pcfg_pull_up_4ma>; + }; + + sdmmc0ext_bus1: sdmmc0ext-bus1 { + rockchip,pins = <3 RK_PA4 3 &pcfg_pull_up_4ma>; + }; + + sdmmc0ext_bus4: sdmmc0ext-bus4 { + rockchip,pins = + <3 RK_PA4 3 &pcfg_pull_up_4ma>, + <3 RK_PA5 3 &pcfg_pull_up_4ma>, + <3 RK_PA6 3 &pcfg_pull_up_4ma>, + <3 RK_PA7 3 &pcfg_pull_up_4ma>; + }; + + sdmmc0ext_gpio: sdmmc0ext-gpio { + rockchip,pins = + <3 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up_4ma>; + }; + }; + + sdmmc1 { + sdmmc1_clk: sdmmc1-clk { + rockchip,pins = <1 RK_PB4 1 &pcfg_pull_none_8ma>; + }; + + sdmmc1_cmd: sdmmc1-cmd { + rockchip,pins = <1 RK_PB5 1 &pcfg_pull_up_8ma>; + }; + + sdmmc1_pwren: sdmmc1-pwren { + rockchip,pins = <1 RK_PC2 1 &pcfg_pull_up_8ma>; + }; + + sdmmc1_wrprt: sdmmc1-wrprt { + rockchip,pins = <1 RK_PC4 1 &pcfg_pull_up_8ma>; + }; + + sdmmc1_dectn: sdmmc1-dectn { + rockchip,pins = <1 RK_PC3 1 &pcfg_pull_up_8ma>; + }; + + sdmmc1_bus1: sdmmc1-bus1 { + rockchip,pins = <1 RK_PB6 1 &pcfg_pull_up_8ma>; + }; + + sdmmc1_bus4: sdmmc1-bus4 { + rockchip,pins = <1 RK_PB6 1 &pcfg_pull_up_8ma>, + <1 RK_PB7 1 &pcfg_pull_up_8ma>, + <1 RK_PC0 1 &pcfg_pull_up_8ma>, + <1 RK_PC1 1 &pcfg_pull_up_8ma>; + }; + + sdmmc1_gpio: sdmmc1-gpio { + rockchip,pins = + <1 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PB7 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PC0 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PC3 RK_FUNC_GPIO &pcfg_pull_up_4ma>, + <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_up_4ma>; + }; + }; + + emmc { + emmc_clk: emmc-clk { + rockchip,pins = <3 RK_PC5 2 &pcfg_pull_none_12ma>; + }; + + emmc_cmd: emmc-cmd { + rockchip,pins = <3 RK_PC3 2 &pcfg_pull_up_12ma>; + }; + + emmc_pwren: emmc-pwren { + rockchip,pins = <3 RK_PC6 2 &pcfg_pull_none>; + }; + + emmc_rstnout: emmc-rstnout { + rockchip,pins = <3 RK_PC4 2 &pcfg_pull_none>; + }; + + emmc_bus1: emmc-bus1 { + rockchip,pins = <0 RK_PA7 2 &pcfg_pull_up_12ma>; + }; + + emmc_bus4: emmc-bus4 { + rockchip,pins = + <0 RK_PA7 2 &pcfg_pull_up_12ma>, + <2 RK_PD4 2 &pcfg_pull_up_12ma>, + <2 RK_PD5 2 &pcfg_pull_up_12ma>, + <2 RK_PD6 2 &pcfg_pull_up_12ma>; + }; + + emmc_bus8: emmc-bus8 { + rockchip,pins = + <0 RK_PA7 2 &pcfg_pull_up_12ma>, + <2 RK_PD4 2 &pcfg_pull_up_12ma>, + <2 RK_PD5 2 &pcfg_pull_up_12ma>, + <2 RK_PD6 2 &pcfg_pull_up_12ma>, + <2 RK_PD7 2 &pcfg_pull_up_12ma>, + <3 RK_PC0 2 &pcfg_pull_up_12ma>, + <3 RK_PC1 2 &pcfg_pull_up_12ma>, + <3 RK_PC2 2 &pcfg_pull_up_12ma>; + }; + }; + + pwm0 { + pwm0_pin: pwm0-pin { + rockchip,pins = <2 RK_PA4 1 &pcfg_pull_none>; + }; + }; + + pwm1 { + pwm1_pin: pwm1-pin { + rockchip,pins = <2 RK_PA5 1 &pcfg_pull_none>; + }; + }; + + pwm2 { + pwm2_pin: pwm2-pin { + rockchip,pins = <2 RK_PA6 1 &pcfg_pull_none>; + }; + }; + + pwmir { + pwmir_pin: pwmir-pin { + rockchip,pins = <2 RK_PA2 1 &pcfg_pull_none>; + }; + }; + + gmac-1 { + rgmiim1_pins: rgmiim1-pins { + rockchip,pins = + /* mac_txclk */ + <1 RK_PB4 2 &pcfg_pull_none_12ma>, + /* mac_rxclk */ + <1 RK_PB5 2 &pcfg_pull_none_2ma>, + /* mac_mdio */ + <1 RK_PC3 2 &pcfg_pull_none_2ma>, + /* mac_txen */ + <1 RK_PD1 2 &pcfg_pull_none_12ma>, + /* mac_clk */ + <1 RK_PC5 2 &pcfg_pull_none_2ma>, + /* mac_rxdv */ + <1 RK_PC6 2 &pcfg_pull_none_2ma>, + /* mac_mdc */ + <1 RK_PC7 2 &pcfg_pull_none_2ma>, + /* mac_rxd1 */ + <1 RK_PB2 2 &pcfg_pull_none_2ma>, + /* mac_rxd0 */ + <1 RK_PB3 2 &pcfg_pull_none_2ma>, + /* mac_txd1 */ + <1 RK_PB0 2 &pcfg_pull_none_12ma>, + /* mac_txd0 */ + <1 RK_PB1 2 &pcfg_pull_none_12ma>, + /* mac_rxd3 */ + <1 RK_PB6 2 &pcfg_pull_none_2ma>, + /* mac_rxd2 */ + <1 RK_PB7 2 &pcfg_pull_none_2ma>, + /* mac_txd3 */ + <1 RK_PC0 2 &pcfg_pull_none_12ma>, + /* mac_txd2 */ + <1 RK_PC1 2 &pcfg_pull_none_12ma>, + + /* mac_txclk */ + <0 RK_PB0 1 &pcfg_pull_none>, + /* mac_txen */ + <0 RK_PB4 1 &pcfg_pull_none>, + /* mac_clk */ + <0 RK_PD0 1 &pcfg_pull_none>, + /* mac_txd1 */ + <0 RK_PC0 1 &pcfg_pull_none>, + /* mac_txd0 */ + <0 RK_PC1 1 &pcfg_pull_none>, + /* mac_txd3 */ + <0 RK_PC7 1 &pcfg_pull_none>, + /* mac_txd2 */ + <0 RK_PC6 1 &pcfg_pull_none>; + }; + + rmiim1_pins: rmiim1-pins { + rockchip,pins = + /* mac_mdio */ + <1 RK_PC3 2 &pcfg_pull_none_2ma>, + /* mac_txen */ + <1 RK_PD1 2 &pcfg_pull_none_12ma>, + /* mac_clk */ + <1 RK_PC5 2 &pcfg_pull_none_2ma>, + /* mac_rxer */ + <1 RK_PD0 2 &pcfg_pull_none_2ma>, + /* mac_rxdv */ + <1 RK_PC6 2 &pcfg_pull_none_2ma>, + /* mac_mdc */ + <1 RK_PC7 2 &pcfg_pull_none_2ma>, + /* mac_rxd1 */ + <1 RK_PB2 2 &pcfg_pull_none_2ma>, + /* mac_rxd0 */ + <1 RK_PB3 2 &pcfg_pull_none_2ma>, + /* mac_txd1 */ + <1 RK_PB0 2 &pcfg_pull_none_12ma>, + /* mac_txd0 */ + <1 RK_PB1 2 &pcfg_pull_none_12ma>, + + /* mac_mdio */ + <0 RK_PB3 1 &pcfg_pull_none>, + /* mac_txen */ + <0 RK_PB4 1 &pcfg_pull_none>, + /* mac_clk */ + <0 RK_PD0 1 &pcfg_pull_none>, + /* mac_mdc */ + <0 RK_PC3 1 &pcfg_pull_none>, + /* mac_txd1 */ + <0 RK_PC0 1 &pcfg_pull_none>, + /* mac_txd0 */ + <0 RK_PC1 1 &pcfg_pull_none>; + }; + }; + + gmac2phy { + fephyled_speed100: fephyled-speed100 { + rockchip,pins = <0 RK_PD7 1 &pcfg_pull_none>; + }; + + fephyled_speed10: fephyled-speed10 { + rockchip,pins = <0 RK_PD6 1 &pcfg_pull_none>; + }; + + fephyled_duplex: fephyled-duplex { + rockchip,pins = <0 RK_PD6 2 &pcfg_pull_none>; + }; + + fephyled_rxm0: fephyled-rxm0 { + rockchip,pins = <0 RK_PD5 1 &pcfg_pull_none>; + }; + + fephyled_txm0: fephyled-txm0 { + rockchip,pins = <0 RK_PD5 2 &pcfg_pull_none>; + }; + + fephyled_linkm0: fephyled-linkm0 { + rockchip,pins = <0 RK_PD4 1 &pcfg_pull_none>; + }; + + fephyled_rxm1: fephyled-rxm1 { + rockchip,pins = <2 RK_PD1 2 &pcfg_pull_none>; + }; + + fephyled_txm1: fephyled-txm1 { + rockchip,pins = <2 RK_PD1 3 &pcfg_pull_none>; + }; + + fephyled_linkm1: fephyled-linkm1 { + rockchip,pins = <2 RK_PD0 2 &pcfg_pull_none>; + }; + }; + + tsadc_pin { + tsadc_int: tsadc-int { + rockchip,pins = <2 RK_PB5 2 &pcfg_pull_none>; + }; + tsadc_gpio: tsadc-gpio { + rockchip,pins = <2 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + hdmi_pin { + hdmi_cec: hdmi-cec { + rockchip,pins = <0 RK_PA3 1 &pcfg_pull_none>; + }; + + hdmi_hpd: hdmi-hpd { + rockchip,pins = <0 RK_PA4 1 &pcfg_pull_down>; + }; + }; + + cif-0 { + dvp_d2d9_m0:dvp-d2d9-m0 { + rockchip,pins = + /* cif_d0 */ + <3 RK_PA4 2 &pcfg_pull_none>, + /* cif_d1 */ + <3 RK_PA5 2 &pcfg_pull_none>, + /* cif_d2 */ + <3 RK_PA6 2 &pcfg_pull_none>, + /* cif_d3 */ + <3 RK_PA7 2 &pcfg_pull_none>, + /* cif_d4 */ + <3 RK_PB0 2 &pcfg_pull_none>, + /* cif_d5m0 */ + <3 RK_PB1 2 &pcfg_pull_none>, + /* cif_d6m0 */ + <3 RK_PB2 2 &pcfg_pull_none>, + /* cif_d7m0 */ + <3 RK_PB3 2 &pcfg_pull_none>, + /* cif_href */ + <3 RK_PA1 2 &pcfg_pull_none>, + /* cif_vsync */ + <3 RK_PA0 2 &pcfg_pull_none>, + /* cif_clkoutm0 */ + <3 RK_PA3 2 &pcfg_pull_none>, + /* cif_clkin */ + <3 RK_PA2 2 &pcfg_pull_none>; + }; + }; + + cif-1 { + dvp_d2d9_m1:dvp-d2d9-m1 { + rockchip,pins = + /* cif_d0 */ + <3 RK_PA4 2 &pcfg_pull_none>, + /* cif_d1 */ + <3 RK_PA5 2 &pcfg_pull_none>, + /* cif_d2 */ + <3 RK_PA6 2 &pcfg_pull_none>, + /* cif_d3 */ + <3 RK_PA7 2 &pcfg_pull_none>, + /* cif_d4 */ + <3 RK_PB0 2 &pcfg_pull_none>, + /* cif_d5m1 */ + <2 RK_PC0 4 &pcfg_pull_none>, + /* cif_d6m1 */ + <2 RK_PC1 4 &pcfg_pull_none>, + /* cif_d7m1 */ + <2 RK_PC2 4 &pcfg_pull_none>, + /* cif_href */ + <3 RK_PA1 2 &pcfg_pull_none>, + /* cif_vsync */ + <3 RK_PA0 2 &pcfg_pull_none>, + /* cif_clkoutm1 */ + <2 RK_PB7 4 &pcfg_pull_none>, + /* cif_clkin */ + <3 RK_PA2 2 &pcfg_pull_none>; + }; + }; + }; +}; diff --git a/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts b/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts index 8cdb3bff9c55..ff48edd8e348 100644 --- a/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts +++ b/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts @@ -53,7 +53,7 @@ }; memory@0 { - reg = <0x0 0x0 0x0 0x80000000>; + reg = <0x0 0x0 0x0 0x40000000>; device_type = "memory"; }; diff --git a/arch/arm64/boot/dts/rockchip/rk3368.dtsi b/arch/arm64/boot/dts/rockchip/rk3368.dtsi index a635adc47e74..6d5dc0587e59 100644 --- a/arch/arm64/boot/dts/rockchip/rk3368.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3368.dtsi @@ -108,23 +108,10 @@ }; }; - idle-states { - entry-method = "psci"; - - cpu_sleep: cpu-sleep-0 { - compatible = "arm,idle-state"; - arm,psci-suspend-param = <0x1010000>; - entry-latency-us = <0x3fffffff>; - exit-latency-us = <0x40000000>; - min-residency-us = <0xffffffff>; - }; - }; - cpu_l0: cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x0 0x0>; - cpu-idle-states = <&cpu_sleep>; enable-method = "psci"; #cooling-cells = <2>; /* min followed by max */ @@ -134,7 +121,6 @@ device_type = "cpu"; compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x0 0x1>; - cpu-idle-states = <&cpu_sleep>; enable-method = "psci"; }; @@ -142,7 +128,6 @@ device_type = "cpu"; compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x0 0x2>; - cpu-idle-states = <&cpu_sleep>; enable-method = "psci"; }; @@ -150,7 +135,6 @@ device_type = "cpu"; compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x0 0x3>; - cpu-idle-states = <&cpu_sleep>; enable-method = "psci"; }; @@ -158,7 +142,6 @@ device_type = "cpu"; compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x0 0x100>; - cpu-idle-states = <&cpu_sleep>; enable-method = "psci"; #cooling-cells = <2>; /* min followed by max */ @@ -168,7 +151,6 @@ device_type = "cpu"; compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x0 0x101>; - cpu-idle-states = <&cpu_sleep>; enable-method = "psci"; }; @@ -176,7 +158,6 @@ device_type = "cpu"; compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x0 0x102>; - cpu-idle-states = <&cpu_sleep>; enable-method = "psci"; }; @@ -184,11 +165,39 @@ device_type = "cpu"; compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x0 0x103>; - cpu-idle-states = <&cpu_sleep>; enable-method = "psci"; }; }; + amba { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + dmac_peri: dma-controller@ff250000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff250000 0x0 0x4000>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + arm,pl330-broken-no-flushp; + clocks = <&cru ACLK_DMAC_PERI>; + clock-names = "apb_pclk"; + }; + + dmac_bus: dma-controller@ff600000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff600000 0x0 0x4000>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + arm,pl330-broken-no-flushp; + clocks = <&cru ACLK_DMAC_BUS>; + clock-names = "apb_pclk"; + }; + }; + arm-pmu { compatible = "arm,armv8-pmuv3"; interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>, @@ -237,6 +246,8 @@ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; fifo-depth = <0x100>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + resets = <&cru SRST_MMC0>; + reset-names = "reset"; status = "disabled"; }; @@ -249,6 +260,8 @@ clock-names = "biu", "ciu", "ciu_drv", "ciu_sample"; fifo-depth = <0x100>; interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + resets = <&cru SRST_SDIO0>; + reset-names = "reset"; status = "disabled"; }; @@ -261,6 +274,8 @@ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; fifo-depth = <0x100>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + resets = <&cru SRST_EMMC>; + reset-names = "reset"; status = "disabled"; }; @@ -631,6 +646,7 @@ clocks = <&cru PCLK_MAILBOX>; clock-names = "pclk_mailbox"; #mbox-cells = <1>; + status = "disabled"; }; pmugrf: syscon@ff738000 { @@ -684,6 +700,30 @@ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; }; + i2s_2ch: i2s-2ch@ff890000 { + compatible = "rockchip,rk3368-i2s", "rockchip,rk3066-i2s"; + reg = <0x0 0xff890000 0x0 0x1000>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "i2s_clk", "i2s_hclk"; + clocks = <&cru SCLK_I2S_2CH>, <&cru HCLK_I2S_2CH>; + dmas = <&dmac_bus 6>, <&dmac_bus 7>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + i2s_8ch: i2s-8ch@ff898000 { + compatible = "rockchip,rk3368-i2s", "rockchip,rk3066-i2s"; + reg = <0x0 0xff898000 0x0 0x1000>; + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "i2s_clk", "i2s_hclk"; + clocks = <&cru SCLK_I2S_8CH>, <&cru HCLK_I2S_8CH>; + dmas = <&dmac_bus 0>, <&dmac_bus 1>; + dma-names = "tx", "rx"; + pinctrl-names = "default"; + pinctrl-0 = <&i2s_8ch_bus>; + status = "disabled"; + }; + gic: interrupt-controller@ffb71000 { compatible = "arm,gic-400"; interrupt-controller; @@ -886,6 +926,20 @@ }; }; + i2s { + i2s_8ch_bus: i2s-8ch-bus { + rockchip,pins = <2 12 RK_FUNC_1 &pcfg_pull_none>, + <2 13 RK_FUNC_1 &pcfg_pull_none>, + <2 14 RK_FUNC_1 &pcfg_pull_none>, + <2 15 RK_FUNC_1 &pcfg_pull_none>, + <2 16 RK_FUNC_1 &pcfg_pull_none>, + <2 17 RK_FUNC_1 &pcfg_pull_none>, + <2 18 RK_FUNC_1 &pcfg_pull_none>, + <2 19 RK_FUNC_1 &pcfg_pull_none>, + <2 20 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + pwm0 { pwm0_pin: pwm0-pin { rockchip,pins = <3 8 RK_FUNC_2 &pcfg_pull_none>; diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts b/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts new file mode 100644 index 000000000000..658bb9dc9dfd --- /dev/null +++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts @@ -0,0 +1,306 @@ +/* + * Google Gru-Kevin Rev 6+ board device tree source + * + * Copyright 2016-2017 Google, Inc + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "rk3399-gru.dtsi" +#include <include/dt-bindings/input/linux-event-codes.h> + +/* + * Kevin-specific things + * + * Things in this section should use names from Kevin schematic since no + * equivalent exists in Gru schematic. If referring to signals that exist + * in Gru we use the Gru names, though. Confusing enough for you? + */ +/ { + model = "Google Kevin"; + compatible = "google,kevin-rev15", "google,kevin-rev14", + "google,kevin-rev13", "google,kevin-rev12", + "google,kevin-rev11", "google,kevin-rev10", + "google,kevin-rev9", "google,kevin-rev8", + "google,kevin-rev7", "google,kevin-rev6", + "google,kevin", "google,gru", "rockchip,rk3399"; + + /* Power tree */ + + p3_3v_dig: p3-3v-dig { + compatible = "regulator-fixed"; + regulator-name = "p3.3v_dig"; + pinctrl-names = "default"; + pinctrl-0 = <&cpu3_pen_pwr_en>; + + enable-active-high; + gpio = <&gpio4 30 GPIO_ACTIVE_HIGH>; + vin-supply = <&pp3300>; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&cros_ec_pwm 1>; + brightness-levels = <0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 + 17 18 19 20 21 22 23 24 25 26 27 28 29 30 + 31 32 33 34 35 36 37 38 39 40 41 42 43 44 + 45 46 47 48 49 50 51 52 53 54 55 56 57 58 + 59 60 61 62 63 64 65 66 67 68 69 70 71 72 + 73 74 75 76 77 78 79 80 81 82 83 84 85 86 + 87 88 89 90 91 92 93 94 95 96 97 98 99 100>; + default-brightness-level = <51>; + enable-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + power-supply = <&pp3300_disp>; + pinctrl-names = "default"; + pinctrl-0 = <&bl_en>; + pwm-delay-us = <10000>; + }; + + thermistor_ppvar_bigcpu: thermistor-ppvar-bigcpu { + compatible = "murata,ncp15wb473"; + pullup-uv = <1800000>; + pullup-ohm = <25500>; + pulldown-ohm = <0>; + io-channels = <&saradc 2>; + #thermal-sensor-cells = <0>; + }; + + thermistor_ppvar_litcpu: thermistor-ppvar-litcpu { + compatible = "murata,ncp15wb473"; + pullup-uv = <1800000>; + pullup-ohm = <25500>; + pulldown-ohm = <0>; + io-channels = <&saradc 3>; + #thermal-sensor-cells = <0>; + }; +}; + +&gpio_keys { + pinctrl-names = "default"; + pinctrl-0 = <&bt_host_wake_l>, <&cpu1_pen_eject>; + + pen-insert { + label = "Pen Insert"; + /* Insert = low, eject = high */ + gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + linux,code = <SW_PEN_INSERTED>; + linux,input-type = <EV_SW>; + wakeup-source; + }; +}; + +&thermal_zones { + bigcpu_reg_thermal: bigcpu-reg-thermal { + polling-delay-passive = <100>; /* milliseconds */ + polling-delay = <1000>; /* milliseconds */ + thermal-sensors = <&thermistor_ppvar_bigcpu 0>; + sustainable-power = <4000>; + + ppvar_bigcpu_trips: trips { + ppvar_bigcpu_on: ppvar-bigcpu-on { + temperature = <40000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + + ppvar_bigcpu_alert: ppvar-bigcpu-alert { + temperature = <50000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + + ppvar_bigcpu_crit: ppvar-bigcpu-crit { + temperature = <90000>; /* millicelsius */ + hysteresis = <0>; /* millicelsius */ + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&ppvar_bigcpu_alert>; + cooling-device = + <&cpu_l0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + contribution = <4096>; + }; + map1 { + trip = <&ppvar_bigcpu_alert>; + cooling-device = + <&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + contribution = <1024>; + }; + }; + }; + + litcpu_reg_thermal: litcpu-reg-thermal { + polling-delay-passive = <100>; /* milliseconds */ + polling-delay = <1000>; /* milliseconds */ + thermal-sensors = <&thermistor_ppvar_litcpu 0>; + sustainable-power = <4000>; + + ppvar_litcpu_trips: trips { + ppvar_litcpu_on: ppvar-litcpu-on { + temperature = <40000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + + ppvar_litcpu_alert: ppvar-litcpu-alert { + temperature = <50000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + + ppvar_litcpu_crit: ppvar-litcpu-crit { + temperature = <90000>; /* millicelsius */ + hysteresis = <0>; /* millicelsius */ + type = "critical"; + }; + }; + }; +}; + +ap_i2c_tpm: &i2c0 { + status = "okay"; + + clock-frequency = <400000>; + + /* These are relatively safe rise/fall times. */ + i2c-scl-falling-time-ns = <50>; + i2c-scl-rising-time-ns = <300>; + + tpm: tpm@20 { + compatible = "infineon,slb9645tt"; + reg = <0x20>; + powered-while-suspended; + }; +}; + +ap_i2c_dig: &i2c2 { + status = "okay"; + + clock-frequency = <400000>; + + /* These are relatively safe rise/fall times. */ + i2c-scl-falling-time-ns = <50>; + i2c-scl-rising-time-ns = <300>; + + digitizer: digitizer@9 { + /* wacom,w9013 */ + compatible = "hid-over-i2c"; + reg = <0x9>; + pinctrl-names = "default"; + pinctrl-0 = <&cpu1_dig_irq_l &cpu1_dig_pdct_l>; + + vdd-supply = <&p3_3v_dig>; + post-power-on-delay-ms = <100>; + + interrupt-parent = <&gpio2>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + + hid-descr-addr = <0x1>; + }; +}; + +/* Adjustments to things in the gru baseboard */ + +&ap_i2c_tp { + trackpad@4a { + compatible = "atmel,atmel_mxt_tp"; + reg = <0x4a>; + pinctrl-names = "default"; + pinctrl-0 = <&trackpad_int_l>; + interrupt-parent = <&gpio1>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + wakeup-source; + }; +}; + +&ap_i2c_ts { + touchscreen@4b { + compatible = "atmel,atmel_mxt_ts"; + reg = <0x4b>; + pinctrl-names = "default"; + pinctrl-0 = <&touch_int_l>; + interrupt-parent = <&gpio3>; + interrupts = <13 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&saradc { + status = "okay"; + vref-supply = <&pp1800_ap_io>; +}; + +&mvl_wifi { + marvell,wakeup-pin = <14>; /* GPIO_14 on Marvell */ +}; + +&pinctrl { + digitizer { + /* Has external pullup */ + cpu1_dig_irq_l: cpu1-dig-irq-l { + rockchip,pins = <2 4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + /* Has external pullup */ + cpu1_dig_pdct_l: cpu1-dig-pdct-l { + rockchip,pins = <2 5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + discrete-regulators { + cpu3_pen_pwr_en: cpu3-pen-pwr-en { + rockchip,pins = <4 30 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pen { + cpu1_pen_eject: cpu1-pen-eject { + rockchip,pins = <0 13 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + wifi { + wlan_host_wake_l: wlan-host-wake-l { + rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi new file mode 100644 index 000000000000..0d960b7f7625 --- /dev/null +++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi @@ -0,0 +1,1103 @@ +/* + * Google Gru (and derivatives) board device tree source + * + * Copyright 2016-2017 Google, Inc + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/input/input.h> +#include "rk3399.dtsi" +#include "rk3399-opp.dtsi" + +/ { + chosen { + stdout-path = "serial2:115200n8"; + }; + + /* + * Power Tree + * + * In general an attempt is made to include all rails called out by + * the schematic as long as those rails interact in some way with + * the AP. AKA: + * - Rails that only connect to the EC (or devices that the EC talks to) + * are not included. + * - Rails _are_ included if the rails go to the AP even if the AP + * doesn't currently care about them / they are always on. The idea + * here is that it makes it easier to map to the schematic or extend + * later. + * + * If two rails are substantially the same from the AP's point of + * view, though, we won't create a full fixed regulator. We'll just + * put the child rail as an alias of the parent rail. Sometimes rails + * look the same to the AP because one of these is true: + * - The EC controls the enable and the EC always enables a rail as + * long as the AP is running. + * - The rails are actually connected to each other by a jumper and + * the distinction is just there to add clarity/flexibility to the + * schematic. + */ + + ppvar_sys: ppvar-sys { + compatible = "regulator-fixed"; + regulator-name = "ppvar_sys"; + regulator-always-on; + regulator-boot-on; + }; + + pp900_ap: pp900-ap { + compatible = "regulator-fixed"; + regulator-name = "pp900_ap"; + + /* EC turns on w/ pp900_ap_en; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + vin-supply = <&ppvar_sys>; + }; + + pp1200_lpddr: pp1200-lpddr { + compatible = "regulator-fixed"; + regulator-name = "pp1200_lpddr"; + + /* EC turns on w/ lpddr_pwr_en; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + + vin-supply = <&ppvar_sys>; + }; + + pp1800: pp1800 { + compatible = "regulator-fixed"; + regulator-name = "pp1800"; + + /* Always on when ppvar_sys shows power good */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + vin-supply = <&ppvar_sys>; + }; + + pp3000: pp3000 { + compatible = "regulator-fixed"; + regulator-name = "pp3000"; + pinctrl-names = "default"; + pinctrl-0 = <&pp3000_en>; + + enable-active-high; + gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>; + + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + + vin-supply = <&ppvar_sys>; + }; + + pp3300: pp3300 { + compatible = "regulator-fixed"; + regulator-name = "pp3300"; + + /* Always on; plain and simple */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + vin-supply = <&ppvar_sys>; + }; + + pp5000: pp5000 { + compatible = "regulator-fixed"; + regulator-name = "pp5000"; + + /* EC turns on w/ pp5000_en; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + vin-supply = <&ppvar_sys>; + }; + + ppvar_bigcpu: ppvar-bigcpu { + compatible = "pwm-regulator"; + regulator-name = "ppvar_bigcpu"; + /* + * OVP circuit requires special handling which is not yet + * represented. Keep disabled for now. + */ + status = "disabled"; + + pwms = <&pwm1 0 3337 0>; + pwm-supply = <&ppvar_sys>; + pwm-dutycycle-range = <100 0>; + pwm-dutycycle-unit = <100>; + + /* EC turns on w/ ap_core_en; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <798674>; + regulator-max-microvolt = <1302172>; + }; + + ppvar_litcpu: ppvar-litcpu { + compatible = "pwm-regulator"; + regulator-name = "ppvar_litcpu"; + /* + * OVP circuit requires special handling which is not yet + * represented. Keep disabled for now. + */ + status = "disabled"; + + pwms = <&pwm2 0 3337 0>; + pwm-supply = <&ppvar_sys>; + pwm-dutycycle-range = <100 0>; + pwm-dutycycle-unit = <100>; + + /* EC turns on w/ ap_core_en; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <799065>; + regulator-max-microvolt = <1303738>; + }; + + ppvar_gpu: ppvar-gpu { + compatible = "pwm-regulator"; + regulator-name = "ppvar_gpu"; + /* + * OVP circuit requires special handling which is not yet + * represented. Keep disabled for now. + */ + status = "disabled"; + + pwms = <&pwm0 0 3337 0>; + pwm-supply = <&ppvar_sys>; + pwm-dutycycle-range = <100 0>; + pwm-dutycycle-unit = <100>; + + /* EC turns on w/ ap_core_en; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <785782>; + regulator-max-microvolt = <1217729>; + }; + + ppvar_centerlogic: ppvar-centerlogic { + compatible = "pwm-regulator"; + regulator-name = "ppvar_centerlogic"; + /* + * OVP circuit requires special handling which is not yet + * represented. Keep disabled for now. + */ + status = "disabled"; + + pwms = <&pwm3 0 3337 0>; + pwm-supply = <&ppvar_sys>; + pwm-dutycycle-range = <100 0>; + pwm-dutycycle-unit = <100>; + + /* EC turns on w/ ppvar_centerlogic_en; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <800069>; + regulator-max-microvolt = <1049692>; + }; + + /* Schematics call this PPVAR even though it's fixed */ + ppvar_logic: ppvar-logic { + compatible = "regulator-fixed"; + regulator-name = "ppvar_logic"; + + /* EC turns on w/ ppvar_logic_en; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + vin-supply = <&ppvar_sys>; + }; + + /* EC turns on w/ pp900_ddrpll_en */ + pp900_ddrpll: pp900-ap { + }; + + /* EC turns on w/ pp900_pcie_en */ + pp900_pcie: pp900-ap { + }; + + /* EC turns on w/ pp900_pll_en */ + pp900_pll: pp900-ap { + }; + + /* EC turns on w/ pp900_pmu_en */ + pp900_pmu: pp900-ap { + }; + + /* EC turns on w/ pp900_usb_en */ + pp900_usb: pp900-ap { + }; + + /* EC turns on w/ pp1800_s0_en_l */ + pp1800_ap_io: pp1800_emmc: pp1800_nfc: pp1800_s0: pp1800 { + }; + + /* EC turns on w/ pp1800_avdd_en_l */ + pp1800_avdd: pp1800 { + }; + + /* EC turns on w/ pp1800_lid_en_l */ + pp1800_lid: pp1800_mic: pp1800 { + }; + + /* EC turns on w/ lpddr_pwr_en */ + pp1800_lpddr: pp1800 { + }; + + /* EC turns on w/ pp1800_pmu_en_l */ + pp1800_pmu: pp1800 { + }; + + /* EC turns on w/ pp1800_usb_en_l */ + pp1800_usb: pp1800 { + }; + + pp1500_ap_io: pp1500-ap-io { + compatible = "regulator-fixed"; + regulator-name = "pp1500_ap_io"; + pinctrl-names = "default"; + pinctrl-0 = <&pp1500_en>; + + enable-active-high; + gpio = <&gpio0 10 GPIO_ACTIVE_HIGH>; + + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + + vin-supply = <&pp1800>; + }; + + pp1800_audio: pp1800-audio { + compatible = "regulator-fixed"; + regulator-name = "pp1800_audio"; + pinctrl-names = "default"; + pinctrl-0 = <&pp1800_audio_en>; + + enable-active-high; + gpio = <&gpio0 2 GPIO_ACTIVE_HIGH>; + + regulator-always-on; + regulator-boot-on; + + vin-supply = <&pp1800>; + }; + + /* gpio is shared with pp3300_wifi_bt */ + pp1800_pcie: pp1800-pcie { + compatible = "regulator-fixed"; + regulator-name = "pp1800_pcie"; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_module_pd_l>; + + enable-active-high; + gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>; + + /* + * Need to wait 1ms + ramp-up time before we can power on WiFi. + * This has been approximated as 8ms total. + */ + regulator-enable-ramp-delay = <8000>; + + vin-supply = <&pp1800>; + }; + + /* + * This is a bit of a hack. The WiFi module should be reset at least + * 1ms after its regulators have ramped up (max rampup time is ~7ms). + * With some stretching of the imagination, we can call the 1.8V + * regulator a supply. + */ + wlan_pd_n: wlan-pd-n { + compatible = "regulator-fixed"; + regulator-name = "wlan_pd_n"; + + /* Note the wlan_module_reset_l pinctrl */ + enable-active-high; + gpio = <&gpio1 11 GPIO_ACTIVE_HIGH>; + + vin-supply = <&pp1800_pcie>; + }; + + /* Always on; plain and simple */ + pp3000_ap: pp3000_emmc: pp3000 { + }; + + pp3000_sd_slot: pp3000-sd-slot { + compatible = "regulator-fixed"; + regulator-name = "pp3000_sd_slot"; + pinctrl-names = "default"; + pinctrl-0 = <&sd_slot_pwr_en>; + + enable-active-high; + gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>; + + vin-supply = <&pp3000>; + }; + + /* + * Technically, this is a small abuse of 'regulator-gpio'; this + * regulator is a mux between pp1800 and pp3300. pp1800 and pp3300 are + * always on though, so it is sufficient to simply control the mux + * here. + */ + ppvar_sd_card_io: ppvar-sd-card-io { + compatible = "regulator-gpio"; + regulator-name = "ppvar_sd_card_io"; + pinctrl-names = "default"; + pinctrl-0 = <&sd_io_pwr_en &sd_pwr_1800_sel>; + + enable-active-high; + enable-gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>; + gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 + 3000000 0x0>; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; + + /* EC turns on w/ pp3300_trackpad_en_l */ + pp3300_trackpad: pp3300-trackpad { + }; + + /* EC turns on w/ pp3300_usb_en_l */ + pp3300_usb: pp3300 { + }; + + pp3300_disp: pp3300-disp { + compatible = "regulator-fixed"; + regulator-name = "pp3300_disp"; + pinctrl-names = "default"; + pinctrl-0 = <&pp3300_disp_en>; + + enable-active-high; + gpio = <&gpio4 27 GPIO_ACTIVE_HIGH>; + + startup-delay-us = <2000>; + vin-supply = <&pp3300>; + }; + + /* gpio is shared with pp1800_pcie and pinctrl is set there */ + pp3300_wifi_bt: pp3300-wifi-bt { + compatible = "regulator-fixed"; + regulator-name = "pp3300_wifi_bt"; + + enable-active-high; + gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>; + + vin-supply = <&pp3300>; + }; + + /* EC turns on w/ usb_a_en */ + pp5000_usb_a_vbus: pp5000 { + }; + + gpio_keys: gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&bt_host_wake_l>; + + wake-on-bt { + label = "Wake-on-Bluetooth"; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + linux,code = <KEY_WAKEUP>; + wakeup-source; + }; + }; + + max98357a: max98357a { + compatible = "maxim,max98357a"; + pinctrl-names = "default"; + pinctrl-0 = <&sdmode_en>; + sdmode-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + sdmode-delay = <2>; + #sound-dai-cells = <0>; + status = "okay"; + }; + + sound { + compatible = "rockchip,rk3399-gru-sound"; + rockchip,cpu = <&i2s0 &i2s2>; + rockchip,codec = <&max98357a &headsetcodec &codec>; + }; +}; + +/* + * Set some suspend operating points to avoid OVP in suspend + * + * When we go into S3 ARM Trusted Firmware will transition our PWM regulators + * from wherever they're at back to the "default" operating point (whatever + * voltage we get when we set the PWM pins to "input"). + * + * This quick transition under light load has the possibility to trigger the + * regulator "over voltage protection" (OVP). + * + * To make extra certain that we don't hit this OVP at suspend time, we'll + * transition to a voltage that's much closer to the default (~1.0 V) so that + * there will not be a big jump. Technically we only need to get within 200 mV + * of the default voltage, but the speed here should be fast enough and we need + * suspend/resume to be rock solid. + */ + +&cluster0_opp { + opp05 { + opp-suspend; + }; +}; + +&cluster1_opp { + opp06 { + opp-suspend; + }; +}; + +&cpu_l0 { + cpu-supply = <&ppvar_litcpu>; +}; + +&cpu_l1 { + cpu-supply = <&ppvar_litcpu>; +}; + +&cpu_l2 { + cpu-supply = <&ppvar_litcpu>; +}; + +&cpu_l3 { + cpu-supply = <&ppvar_litcpu>; +}; + +&cpu_b0 { + cpu-supply = <&ppvar_bigcpu>; +}; + +&cpu_b1 { + cpu-supply = <&ppvar_bigcpu>; +}; + + +&cru { + assigned-clocks = + <&cru PLL_GPLL>, <&cru PLL_CPLL>, + <&cru PLL_NPLL>, + <&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>, + <&cru PCLK_PERIHP>, + <&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>, + <&cru PCLK_PERILP0>, <&cru ACLK_CCI>, + <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>; + assigned-clock-rates = + <600000000>, <800000000>, + <1000000000>, + <150000000>, <75000000>, + <37500000>, + <100000000>, <100000000>, + <50000000>, <800000000>, + <100000000>, <50000000>; +}; + +&emmc_phy { + status = "okay"; +}; + +ap_i2c_mic: &i2c1 { + status = "okay"; + + clock-frequency = <400000>; + + /* These are relatively safe rise/fall times */ + i2c-scl-falling-time-ns = <50>; + i2c-scl-rising-time-ns = <300>; + + headsetcodec: rt5514@57 { + compatible = "realtek,rt5514"; + reg = <0x57>; + interrupt-parent = <&gpio1>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mic_int>; + realtek,dmic-init-delay = <20>; + wakeup-source; + }; +}; + +ap_i2c_ts: &i2c3 { + status = "okay"; + + clock-frequency = <400000>; + + /* These are relatively safe rise/fall times */ + i2c-scl-falling-time-ns = <50>; + i2c-scl-rising-time-ns = <300>; +}; + +ap_i2c_tp: &i2c5 { + status = "okay"; + + clock-frequency = <400000>; + + /* These are relatively safe rise/fall times */ + i2c-scl-falling-time-ns = <50>; + i2c-scl-rising-time-ns = <300>; + + /* + * Note strange pullup enable. Apparently this avoids leakage but + * still allows us to get nice 4.7K pullups for high speed i2c + * transfers. Basically we want the pullup on whenever the ap is + * alive, so the "en" pin just gets set to output high. + */ + pinctrl-0 = <&i2c5_xfer &ap_i2c_tp_pu_en>; +}; + +ap_i2c_audio: &i2c8 { + status = "okay"; + + clock-frequency = <400000>; + + /* These are relatively safe rise/fall times */ + i2c-scl-falling-time-ns = <50>; + i2c-scl-rising-time-ns = <300>; + + codec: da7219@1a { + compatible = "dlg,da7219"; + reg = <0x1a>; + interrupt-parent = <&gpio1>; + interrupts = <23 IRQ_TYPE_LEVEL_LOW>; + clocks = <&cru SCLK_I2S_8CH_OUT>; + clock-names = "mclk"; + dlg,micbias-lvl = <2600>; + dlg,mic-amp-in-sel = "diff"; + pinctrl-names = "default"; + pinctrl-0 = <&headset_int_l>; + VDD-supply = <&pp1800>; + VDDMIC-supply = <&pp3300>; + VDDIO-supply = <&pp1800>; + + da7219_aad { + dlg,adc-1bit-rpt = <1>; + dlg,btn-avg = <4>; + dlg,btn-cfg = <50>; + dlg,mic-det-thr = <500>; + dlg,jack-ins-deb = <20>; + dlg,jack-det-rate = "32ms_64ms"; + dlg,jack-rem-deb = <1>; + + dlg,a-d-btn-thr = <0xa>; + dlg,d-b-btn-thr = <0x16>; + dlg,b-c-btn-thr = <0x21>; + dlg,c-mic-btn-thr = <0x3E>; + }; + }; +}; + +&i2s0 { + status = "okay"; +}; + +&i2s2 { + status = "okay"; +}; + +&io_domains { + status = "okay"; + + audio-supply = <&pp1800_audio>; /* APIO5_VDD; 3d 4a */ + bt656-supply = <&pp1800_ap_io>; /* APIO2_VDD; 2a 2b */ + gpio1830-supply = <&pp3000_ap>; /* APIO4_VDD; 4c 4d */ + sdmmc-supply = <&ppvar_sd_card_io>; /* SDMMC0_VDD; 4b */ +}; + +&pcie0 { + status = "okay"; + + ep-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie_clkreqn_cpm>, <&wifi_perst_l>; + vpcie3v3-supply = <&pp3300_wifi_bt>; + vpcie1v8-supply = <&wlan_pd_n>; /* HACK: see &wlan_pd_n */ + vpcie0v9-supply = <&pp900_pcie>; + + pci_rootport: pcie@0,0 { + reg = <0x83000000 0x0 0x00000000 0x0 0x00000000>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + mvl_wifi: wifi@0,0 { + compatible = "pci1b4b,2b42"; + reg = <0x83010000 0x0 0x00000000 0x0 0x00100000 + 0x83010000 0x0 0x00100000 0x0 0x00100000>; + interrupt-parent = <&gpio0>; + interrupts = <8 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_host_wake_l>; + wakeup-source; + }; + }; +}; + +&pcie_phy { + status = "okay"; +}; + +&pmu_io_domains { + status = "okay"; + + pmu1830-supply = <&pp1800_pmu>; /* PMUIO2_VDD */ +}; + +&pwm0 { + status = "okay"; +}; + +&pwm1 { + status = "okay"; +}; + +&pwm2 { + status = "okay"; +}; + +&pwm3 { + status = "okay"; +}; + +&sdhci { + /* + * Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the + * same (or nearly the same) performance for all eMMC that are intended + * to be used. + */ + assigned-clock-rates = <150000000>; + + bus-width = <8>; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + non-removable; + status = "okay"; +}; + +&sdmmc { + status = "okay"; + + /* + * Note: configure "sdmmc_cd" as card detect even though it's actually + * hooked to ground. Because we specified "cd-gpios" below dw_mmc + * should be ignoring card detect anyway. Specifying the pin as + * sdmmc_cd means that even if you've got GRF_SOC_CON7[12] (force_jtag) + * turned on that the system will still make sure the port is + * configured as SDMMC and not JTAG. + */ + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_cd_gpio + &sdmmc_bus4>; + + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + cd-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>; + disable-wp; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + sd-uhs-sdr104; + vmmc-supply = <&pp3000_sd_slot>; + vqmmc-supply = <&ppvar_sd_card_io>; +}; + +&spi1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-1 = <&spi1_sleep>; + + spiflash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + + /* May run faster once verified. */ + spi-max-frequency = <10000000>; + }; +}; + +&spi2 { + status = "okay"; + + wacky_spi_audio: spi2@0 { + compatible = "realtek,rt5514"; + reg = <0>; + + /* May run faster once verified. */ + spi-max-frequency = <10000000>; + }; +}; + +&spi5 { + status = "okay"; + + cros_ec: ec@0 { + compatible = "google,cros-ec-spi"; + reg = <0>; + interrupt-parent = <&gpio0>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ec_ap_int_l>; + spi-max-frequency = <3000000>; + + i2c_tunnel: i2c-tunnel { + compatible = "google,cros-ec-i2c-tunnel"; + google,remote-bus = <4>; + #address-cells = <1>; + #size-cells = <0>; + }; + + cros_ec_pwm: ec-pwm { + compatible = "google,cros-ec-pwm"; + #pwm-cells = <1>; + }; + }; +}; + +&tsadc { + status = "okay"; + + rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */ + rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */ +}; + +&u2phy0 { + status = "okay"; +}; + +&u2phy1 { + status = "okay"; +}; + +&u2phy0_host { + status = "okay"; +}; + +&u2phy1_host { + status = "okay"; +}; + +&u2phy0_otg { + status = "okay"; +}; + +&u2phy1_otg { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&usb_host0_ehci { + status = "okay"; +}; + +&usb_host0_ohci { + status = "okay"; +}; + +&usb_host1_ehci { + status = "okay"; +}; + +&usb_host1_ohci { + status = "okay"; +}; + +&usbdrd3_0 { + status = "okay"; +}; + +&usbdrd_dwc3_0 { + status = "okay"; + dr_mode = "host"; +}; + +&usbdrd3_1 { + status = "okay"; +}; + +&usbdrd_dwc3_1 { + status = "okay"; + dr_mode = "host"; +}; + +#include <arm/cros-ec-keyboard.dtsi> +#include <arm/cros-ec-sbs.dtsi> + +&pinctrl { + /* + * pinctrl settings for pins that have no real owners. + * + * At the moment settings are identical for S0 and S3, but if we later + * need to configure things differently for S3 we'll adjust here. + */ + pinctrl-names = "default"; + pinctrl-0 = < + &ap_pwroff /* AP will auto-assert this when in S3 */ + &clk_32k /* This pin is always 32k on gru boards */ + + /* + * We want this driven low ASAP; firmware should help us, but + * we can help ourselves too. + */ + &wlan_module_reset_l + >; + + pcfg_output_low: pcfg-output-low { + output-low; + }; + + pcfg_output_high: pcfg-output-high { + output-high; + }; + + pcfg_pull_none_8ma: pcfg-pull-none-8ma { + bias-disable; + drive-strength = <8>; + }; + + backlight-enable { + bl_en: bl-en { + rockchip,pins = <1 17 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + cros-ec { + ec_ap_int_l: ec-ap-int-l { + rockchip,pins = <RK_GPIO0 1 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + discrete-regulators { + pp1500_en: pp1500-en { + rockchip,pins = <RK_GPIO0 10 RK_FUNC_GPIO + &pcfg_pull_none>; + }; + + pp1800_audio_en: pp1800-audio-en { + rockchip,pins = <RK_GPIO0 2 RK_FUNC_GPIO + &pcfg_pull_down>; + }; + + pp3300_disp_en: pp3300-disp-en { + rockchip,pins = <RK_GPIO4 27 RK_FUNC_GPIO + &pcfg_pull_none>; + }; + + pp3000_en: pp3000-en { + rockchip,pins = <RK_GPIO0 12 RK_FUNC_GPIO + &pcfg_pull_none>; + }; + + sd_io_pwr_en: sd-io-pwr-en { + rockchip,pins = <RK_GPIO2 2 RK_FUNC_GPIO + &pcfg_pull_none>; + }; + + sd_pwr_1800_sel: sd-pwr-1800-sel { + rockchip,pins = <RK_GPIO2 28 RK_FUNC_GPIO + &pcfg_pull_none>; + }; + + sd_slot_pwr_en: sd-slot-pwr-en { + rockchip,pins = <RK_GPIO4 29 RK_FUNC_GPIO + &pcfg_pull_none>; + }; + + wlan_module_pd_l: wlan-module-pd-l { + rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO + &pcfg_pull_down>; + }; + }; + + codec { + /* Has external pullup */ + headset_int_l: headset-int-l { + rockchip,pins = <1 23 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + mic_int: mic-int { + rockchip,pins = <1 13 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; + + max98357a { + sdmode_en: sdmode-en { + rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; + + pcie { + pcie_clkreqn_cpm: pci-clkreqn-cpm { + /* + * Since our pcie doesn't support ClockPM(CPM), we want + * to hack this as gpio, so the EP could be able to + * de-assert it along and make ClockPM(CPM) work. + */ + rockchip,pins = <2 26 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + sdmmc { + /* + * We run sdmmc at max speed; bump up drive strength. + * We also have external pulls, so disable the internal ones. + */ + sdmmc_bus4: sdmmc-bus4 { + rockchip,pins = + <4 8 RK_FUNC_1 &pcfg_pull_none_8ma>, + <4 9 RK_FUNC_1 &pcfg_pull_none_8ma>, + <4 10 RK_FUNC_1 &pcfg_pull_none_8ma>, + <4 11 RK_FUNC_1 &pcfg_pull_none_8ma>; + }; + + sdmmc_clk: sdmmc-clk { + rockchip,pins = + <4 12 RK_FUNC_1 &pcfg_pull_none_8ma>; + }; + + sdmmc_cmd: sdmmc-cmd { + rockchip,pins = + <4 13 RK_FUNC_1 &pcfg_pull_none_8ma>; + }; + + /* + * In our case the official card detect is hooked to ground + * to avoid getting access to JTAG just by sticking something + * in the SD card slot (see the force_jtag bit in the TRM). + * + * We still configure it as card detect because it doesn't + * hurt and dw_mmc will ignore it. We make sure to disable + * the pull though so we don't burn needless power. + */ + sdmmc_cd: sdmcc-cd { + rockchip,pins = + <0 7 RK_FUNC_1 &pcfg_pull_none>; + }; + + /* This is where we actually hook up CD; has external pull */ + sdmmc_cd_gpio: sdmmc-cd-gpio { + rockchip,pins = <4 24 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + spi1 { + spi1_sleep: spi1-sleep { + /* + * Pull down SPI1 CLK/CS/RX/TX during suspend, to + * prevent leakage. + */ + rockchip,pins = <1 9 RK_FUNC_GPIO &pcfg_pull_down>, + <1 10 RK_FUNC_GPIO &pcfg_pull_down>, + <1 7 RK_FUNC_GPIO &pcfg_pull_down>, + <1 8 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; + + touchscreen { + touch_int_l: touch-int-l { + rockchip,pins = <3 13 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + touch_reset_l: touch-reset-l { + rockchip,pins = <4 26 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + trackpad { + ap_i2c_tp_pu_en: ap-i2c-tp-pu-en { + rockchip,pins = <3 12 RK_FUNC_GPIO &pcfg_output_high>; + }; + + trackpad_int_l: trackpad-int-l { + rockchip,pins = <1 4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + wifi { + wifi_perst_l: wifi-perst-l { + rockchip,pins = <2 27 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + wlan_module_reset_l: wlan-module-reset-l { + /* + * We want this driven low ASAP (As {Soon,Strongly} As + * Possible), to avoid leakage through the powered-down + * WiFi. + */ + rockchip,pins = <1 11 RK_FUNC_GPIO &pcfg_output_low>; + }; + + bt_host_wake_l: bt-host-wake-l { + /* Kevin has an external pull up, but Gru does not */ + rockchip,pins = <0 3 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + write-protect { + ap_fw_wp: ap-fw-wp { + rockchip,pins = <1 18 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/rockchip/rk3399-opp.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-opp.dtsi new file mode 100644 index 000000000000..dd82e16236a8 --- /dev/null +++ b/arch/arm64/boot/dts/rockchip/rk3399-opp.dtsi @@ -0,0 +1,145 @@ +/* + * Copyright (c) 2016-2017 Fuzhou Rockchip Electronics Co., Ltd + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/ { + cluster0_opp: opp-table0 { + compatible = "operating-points-v2"; + opp-shared; + + opp00 { + opp-hz = /bits/ 64 <408000000>; + opp-microvolt = <800000>; + clock-latency-ns = <40000>; + }; + opp01 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <800000>; + }; + opp02 { + opp-hz = /bits/ 64 <816000000>; + opp-microvolt = <800000>; + }; + opp03 { + opp-hz = /bits/ 64 <1008000000>; + opp-microvolt = <875000>; + }; + opp04 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <925000>; + }; + opp05 { + opp-hz = /bits/ 64 <1416000000>; + opp-microvolt = <1050000>; + }; + opp06 { + opp-hz = /bits/ 64 <1512000000>; + opp-microvolt = <1125000>; + }; + }; + + cluster1_opp: opp-table1 { + compatible = "operating-points-v2"; + opp-shared; + + opp00 { + opp-hz = /bits/ 64 <408000000>; + opp-microvolt = <800000>; + clock-latency-ns = <40000>; + }; + opp01 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <800000>; + }; + opp02 { + opp-hz = /bits/ 64 <816000000>; + opp-microvolt = <825000>; + }; + opp03 { + opp-hz = /bits/ 64 <1008000000>; + opp-microvolt = <875000>; + }; + opp04 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <950000>; + }; + opp05 { + opp-hz = /bits/ 64 <1416000000>; + opp-microvolt = <1025000>; + }; + opp06 { + opp-hz = /bits/ 64 <1608000000>; + opp-microvolt = <1075000>; + }; + opp07 { + opp-hz = /bits/ 64 <1800000000>; + opp-microvolt = <1150000>; + }; + opp08 { + opp-hz = /bits/ 64 <2016000000>; + opp-microvolt = <1250000>; + }; + }; +}; + +&cpu_l0 { + operating-points-v2 = <&cluster0_opp>; +}; + +&cpu_l1 { + operating-points-v2 = <&cluster0_opp>; +}; + +&cpu_l2 { + operating-points-v2 = <&cluster0_opp>; +}; + +&cpu_l3 { + operating-points-v2 = <&cluster0_opp>; +}; + +&cpu_b0 { + operating-points-v2 = <&cluster1_opp>; +}; + +&cpu_b1 { + operating-points-v2 = <&cluster1_opp>; +}; diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi index 8e6d1bdeb9c3..f4f3c96c798d 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi @@ -211,6 +211,51 @@ }; }; + pcie0: pcie@f8000000 { + compatible = "rockchip,rk3399-pcie"; + reg = <0x0 0xf8000000 0x0 0x2000000>, + <0x0 0xfd000000 0x0 0x1000000>; + reg-names = "axi-base", "apb-base"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + aspm-no-l0s; + bus-range = <0x0 0x1>; + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, + <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>; + clock-names = "aclk", "aclk-perf", + "hclk", "pm"; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "sys", "legacy", "client"; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie0_intc 0>, + <0 0 0 2 &pcie0_intc 1>, + <0 0 0 3 &pcie0_intc 2>, + <0 0 0 4 &pcie0_intc 3>; + linux,pci-domain = <0>; + max-link-speed = <1>; + msi-map = <0x0 &its 0x0 0x1000>; + phys = <&pcie_phy>; + phy-names = "pcie-phy"; + ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x600000 + 0x81000000 0x0 0xfa600000 0x0 0xfa600000 0x0 0x100000>; + resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>, + <&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, + <&cru SRST_A_PCIE>; + reset-names = "core", "mgmt", "mgmt-sticky", "pipe", + "pm", "pclk", "aclk"; + status = "disabled"; + + pcie0_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; + gmac: ethernet@fe300000 { compatible = "rockchip,rk3399-gmac"; reg = <0x0 0xfe300000 0x0 0x10000>; @@ -241,6 +286,8 @@ <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>; clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; fifo-depth = <0x100>; + resets = <&cru SRST_SDIO0>; + reset-names = "reset"; status = "disabled"; }; @@ -255,6 +302,8 @@ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; fifo-depth = <0x100>; power-domains = <&power RK3399_PD_SD>; + resets = <&cru SRST_SDMMC>; + reset-names = "reset"; status = "disabled"; }; @@ -275,50 +324,6 @@ status = "disabled"; }; - pcie0: pcie@f8000000 { - compatible = "rockchip,rk3399-pcie"; - reg = <0x0 0xf8000000 0x0 0x2000000>, - <0x0 0xfd000000 0x0 0x1000000>; - reg-names = "axi-base", "apb-base"; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - aspm-no-l0s; - bus-range = <0x0 0x1>; - clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, - <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>; - clock-names = "aclk", "aclk-perf", - "hclk", "pm"; - interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH 0>, - <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH 0>, - <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH 0>; - interrupt-names = "sys", "legacy", "client"; - interrupt-map-mask = <0 0 0 7>; - interrupt-map = <0 0 0 1 &pcie0_intc 0>, - <0 0 0 2 &pcie0_intc 1>, - <0 0 0 3 &pcie0_intc 2>, - <0 0 0 4 &pcie0_intc 3>; - max-link-speed = <1>; - msi-map = <0x0 &its 0x0 0x1000>; - phys = <&pcie_phy>; - phy-names = "pcie-phy"; - ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x600000 - 0x81000000 0x0 0xfa600000 0x0 0xfa600000 0x0 0x100000>; - resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, - <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>, - <&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, - <&cru SRST_A_PCIE>; - reset-names = "core", "mgmt", "mgmt-sticky", "pipe", - "pm", "pclk", "aclk"; - status = "disabled"; - - pcie0_intc: interrupt-controller { - interrupt-controller; - #address-cells = <0>; - #interrupt-cells = <1>; - }; - }; - usb_host0_ehci: usb@fe380000 { compatible = "generic-ehci"; reg = <0x0 0xfe380000 0x0 0x20000>; @@ -371,6 +376,60 @@ status = "disabled"; }; + usbdrd3_0: usb@fe800000 { + compatible = "rockchip,rk3399-dwc3"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, + <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_GRF>; + clock-names = "ref_clk", "suspend_clk", + "bus_clk", "grf_clk"; + status = "disabled"; + + usbdrd_dwc3_0: dwc3 { + compatible = "snps,dwc3"; + reg = <0x0 0xfe800000 0x0 0x100000>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH 0>; + dr_mode = "otg"; + phys = <&u2phy0_otg>; + phy-names = "usb2-phy"; + phy_type = "utmi_wide"; + snps,dis_enblslpm_quirk; + snps,dis-u2-freeclk-exists-quirk; + snps,dis_u2_susphy_quirk; + snps,dis-del-phy-power-chg-quirk; + status = "disabled"; + }; + }; + + usbdrd3_1: usb@fe900000 { + compatible = "rockchip,rk3399-dwc3"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clocks = <&cru SCLK_USB3OTG1_REF>, <&cru SCLK_USB3OTG1_SUSPEND>, + <&cru ACLK_USB3OTG1>, <&cru ACLK_USB3_GRF>; + clock-names = "ref_clk", "suspend_clk", + "bus_clk", "grf_clk"; + status = "disabled"; + + usbdrd_dwc3_1: dwc3 { + compatible = "snps,dwc3"; + reg = <0x0 0xfe900000 0x0 0x100000>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH 0>; + dr_mode = "otg"; + phys = <&u2phy1_otg>; + phy-names = "usb2-phy"; + phy_type = "utmi_wide"; + snps,dis_enblslpm_quirk; + snps,dis-u2-freeclk-exists-quirk; + snps,dis_u2_susphy_quirk; + snps,dis-del-phy-power-chg-quirk; + status = "disabled"; + }; + }; + gic: interrupt-controller@fee00000 { compatible = "arm,gic-v3"; #interrupt-cells = <4>; diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts index 7168cf818ad8..0173e93ab141 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts +++ b/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts @@ -52,11 +52,6 @@ model = "UniPhier LD11 Reference Board"; compatible = "socionext,uniphier-ld11-ref", "socionext,uniphier-ld11"; - memory { - device_type = "memory"; - reg = <0 0x80000000 0 0x40000000>; - }; - chosen { stdout-path = "serial0:115200n8"; }; @@ -73,6 +68,11 @@ i2c4 = &i2c4; i2c5 = &i2c5; }; + + memory@80000000 { + device_type = "memory"; + reg = <0 0x80000000 0 0x40000000>; + }; }; ðsc { diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi index da881f5b6ed4..151c043b4835 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi @@ -140,7 +140,7 @@ <1 10 4>; }; - soc { + soc@0 { compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; @@ -304,6 +304,8 @@ compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc"; reg = <0x5a000000 0x400>; interrupts = <0 78 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_emmc>; clocks = <&sys_clk 4>; bus-width = <8>; mmc-ddr-1_8v; @@ -318,7 +320,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb0>; clocks = <&mio_clk 7>, <&mio_clk 8>, <&mio_clk 12>; - resets = <&mio_rst 7>, <&mio_rst 8>, <&mio_rst 12>, <&sys_rst 8>; + resets = <&sys_rst 8>, <&mio_rst 7>, <&mio_rst 8>, + <&mio_rst 12>; }; usb1: usb@5a810100 { @@ -329,7 +332,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb1>; clocks = <&mio_clk 7>, <&mio_clk 9>, <&mio_clk 13>; - resets = <&mio_rst 7>, <&mio_rst 9>, <&mio_rst 13>, <&sys_rst 8>; + resets = <&sys_rst 8>, <&mio_rst 7>, <&mio_rst 9>, + <&mio_rst 13>; }; usb2: usb@5a820100 { @@ -340,7 +344,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb2>; clocks = <&mio_clk 7>, <&mio_clk 10>, <&mio_clk 14>; - resets = <&mio_rst 7>, <&mio_rst 10>, <&mio_rst 14>, <&sys_rst 8>; + resets = <&sys_rst 8>, <&mio_rst 7>, <&mio_rst 10>, + <&mio_rst 14>; }; mioctrl@5b3e0000 { diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts index 609162a1a322..fca4c479b469 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts +++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts @@ -52,11 +52,6 @@ model = "UniPhier LD20 Reference Board"; compatible = "socionext,uniphier-ld20-ref", "socionext,uniphier-ld20"; - memory { - device_type = "memory"; - reg = <0 0x80000000 0 0xc0000000>; - }; - chosen { stdout-path = "serial0:115200n8"; }; @@ -73,6 +68,11 @@ i2c4 = &i2c4; i2c5 = &i2c5; }; + + memory@80000000 { + device_type = "memory"; + reg = <0 0x80000000 0 0xc0000000>; + }; }; ðsc { diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi index a6b3a70dae83..6193f11acb78 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi @@ -209,7 +209,7 @@ <1 10 4>; }; - soc { + soc@0 { compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; @@ -378,6 +378,8 @@ compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc"; reg = <0x5a000000 0x400>; interrupts = <0 78 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_emmc>; clocks = <&sys_clk 4>; bus-width = <8>; mmc-ddr-1_8v; diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile index b658c5e09b15..f0535e6eaaaa 100644 --- a/arch/arm64/boot/dts/sprd/Makefile +++ b/arch/arm64/boot/dts/sprd/Makefile @@ -1,4 +1,5 @@ -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \ + sp9860g-1h10.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi new file mode 100644 index 000000000000..7b7d8cedacda --- /dev/null +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi @@ -0,0 +1,569 @@ +/* + * Spreadtrum SC9860 SoC + * + * Copyright (C) 2016, Spreadtrum Communications Inc. + * + * SPDX-License-Identifier: (GPL-2.0+ OR MIT) + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include "whale2.dtsi" + +/ { + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu-map { + cluster0 { + core0 { + cpu = <&CPU0>; + }; + core1 { + cpu = <&CPU1>; + }; + core2 { + cpu = <&CPU2>; + }; + core3 { + cpu = <&CPU3>; + }; + }; + + cluster1 { + core0 { + cpu = <&CPU4>; + }; + core1 { + cpu = <&CPU5>; + }; + core2 { + cpu = <&CPU6>; + }; + core3 { + cpu = <&CPU7>; + }; + }; + }; + + CPU0: cpu@530000 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x530000>; + enable-method = "psci"; + cpu-idle-states = <&CORE_PD &CLUSTER_PD>; + }; + + CPU1: cpu@530001 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x530001>; + enable-method = "psci"; + cpu-idle-states = <&CORE_PD &CLUSTER_PD>; + }; + + CPU2: cpu@530002 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x530002>; + enable-method = "psci"; + cpu-idle-states = <&CORE_PD &CLUSTER_PD>; + }; + + CPU3: cpu@530003 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x530003>; + enable-method = "psci"; + cpu-idle-states = <&CORE_PD &CLUSTER_PD>; + }; + + CPU4: cpu@530100 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x530100>; + enable-method = "psci"; + cpu-idle-states = <&CORE_PD &CLUSTER_PD>; + }; + + CPU5: cpu@530101 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x530101>; + enable-method = "psci"; + cpu-idle-states = <&CORE_PD &CLUSTER_PD>; + }; + + CPU6: cpu@530102 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x530102>; + enable-method = "psci"; + cpu-idle-states = <&CORE_PD &CLUSTER_PD>; + }; + + CPU7: cpu@530103 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x530103>; + enable-method = "psci"; + cpu-idle-states = <&CORE_PD &CLUSTER_PD>; + }; + }; + + idle-states{ + entry-method = "arm,psci"; + + CORE_PD: core_pd { + compatible = "arm,idle-state"; + entry-latency-us = <1000>; + exit-latency-us = <700>; + min-residency-us = <2500>; + local-timer-stop; + arm,psci-suspend-param = <0x00010002>; + }; + + CLUSTER_PD: cluster_pd { + compatible = "arm,idle-state"; + entry-latency-us = <1000>; + exit-latency-us = <1000>; + min-residency-us = <3000>; + local-timer-stop; + arm,psci-suspend-param = <0x01010003>; + }; + }; + + gic: interrupt-controller@12001000 { + compatible = "arm,gic-400"; + reg = <0 0x12001000 0 0x1000>, + <0 0x12002000 0 0x2000>, + <0 0x12004000 0 0x2000>, + <0 0x12006000 0 0x2000>; + #interrupt-cells = <3>; + interrupt-controller; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) + | IRQ_TYPE_LEVEL_HIGH)>; + }; + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) + | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) + | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) + | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) + | IRQ_TYPE_LEVEL_LOW)>; + }; + + pmu { + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3"; + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&CPU0>, + <&CPU1>, + <&CPU2>, + <&CPU3>, + <&CPU4>, + <&CPU5>, + <&CPU6>, + <&CPU7>; + }; + + soc { + funnel@10001000 { /* SoC Funnel */ + compatible = "arm,coresight-funnel", "arm,primecell"; + reg = <0 0x10001000 0 0x1000>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + soc_funnel_out_port: endpoint { + remote-endpoint = <&etb_in>; + }; + }; + + port@1 { + reg = <0>; + soc_funnel_in_port0: endpoint { + slave-mode; + remote-endpoint = + <&main_funnel_out_port>; + }; + }; + + port@2 { + reg = <4>; + soc_funnel_in_port1: endpoint { + slave-mode; + remote-endpioint = + <&stm_out_port>; + }; + }; + }; + }; + + etb@10003000 { + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x10003000 0 0x1000>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + port { + etb_in: endpoint { + slave-mode; + remote-endpoint = + <&soc_funnel_out_port>; + }; + }; + }; + + stm@10006000 { + compatible = "arm,coresight-stm", "arm,primecell"; + reg = <0 0x10006000 0 0x1000>, + <0 0x01000000 0 0x180000>; + reg-names = "stm-base", "stm-stimulus-base"; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + port { + stm_out_port: endpoint { + remote-endpoint = + <&soc_funnel_in_port1>; + }; + }; + }; + + funnel@11001000 { /* Cluster0 Funnel */ + compatible = "arm,coresight-funnel", "arm,primecell"; + reg = <0 0x11001000 0 0x1000>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + cluster0_funnel_out_port: endpoint { + remote-endpoint = + <&cluster0_etf_in>; + }; + }; + + port@1 { + reg = <0>; + cluster0_funnel_in_port0: endpoint { + slave-mode; + remote-endpoint = <&etm0_out>; + }; + }; + + port@2 { + reg = <1>; + cluster0_funnel_in_port1: endpoint { + slave-mode; + remote-endpoint = <&etm1_out>; + }; + }; + + port@3 { + reg = <2>; + cluster0_funnel_in_port2: endpoint { + slave-mode; + remote-endpoint = <&etm2_out>; + }; + }; + + port@4 { + reg = <4>; + cluster0_funnel_in_port3: endpoint { + slave-mode; + remote-endpoint = <&etm3_out>; + }; + }; + }; + }; + + funnel@11002000 { /* Cluster1 Funnel */ + compatible = "arm,coresight-funnel", "arm,primecell"; + reg = <0 0x11002000 0 0x1000>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + cluster1_funnel_out_port: endpoint { + remote-endpoint = + <&cluster1_etf_in>; + }; + }; + + port@1 { + reg = <0>; + cluster1_funnel_in_port0: endpoint { + slave-mode; + remote-endpoint = <&etm4_out>; + }; + }; + + port@2 { + reg = <1>; + cluster1_funnel_in_port1: endpoint { + slave-mode; + remote-endpoint = <&etm5_out>; + }; + }; + + port@3 { + reg = <2>; + cluster1_funnel_in_port2: endpoint { + slave-mode; + remote-endpoint = <&etm6_out>; + }; + }; + + port@4 { + reg = <3>; + cluster1_funnel_in_port3: endpoint { + slave-mode; + remote-endpoint = <&etm7_out>; + }; + }; + }; + }; + + etf@11003000 { /* ETF on Cluster0 */ + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x11003000 0 0x1000>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + cluster0_etf_out: endpoint { + remote-endpoint = + <&main_funnel_in_port0>; + }; + }; + + port@1 { + reg = <0>; + cluster0_etf_in: endpoint { + slave-mode; + remote-endpoint = + <&cluster0_funnel_out_port>; + }; + }; + }; + }; + + etf@11004000 { /* ETF on Cluster1 */ + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x11004000 0 0x1000>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + cluster1_etf_out: endpoint { + remote-endpoint = + <&main_funnel_in_port1>; + }; + }; + + port@1 { + reg = <0>; + cluster1_etf_in: endpoint { + slave-mode; + remote-endpoint = + <&cluster1_funnel_out_port>; + }; + }; + }; + }; + + funnel@11005000 { /* Main Funnel */ + compatible = "arm,coresight-funnel", "arm,primecell"; + reg = <0 0x11005000 0 0x1000>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + main_funnel_out_port: endpoint { + remote-endpoint = + <&soc_funnel_in_port0>; + }; + }; + + port@1 { + reg = <0>; + main_funnel_in_port0: endpoint { + slave-mode; + remote-endpoint = + <&cluster0_etf_out>; + }; + }; + + port@2 { + reg = <1>; + main_funnel_in_port1: endpoint { + slave-mode; + remote-endpoint = + <&cluster1_etf_out>; + }; + }; + }; + }; + + etm@11440000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x11440000 0 0x1000>; + cpu = <&CPU0>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + + port { + etm0_out: endpoint { + remote-endpoint = + <&cluster0_funnel_in_port0>; + }; + }; + }; + + etm@11540000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x11540000 0 0x1000>; + cpu = <&CPU1>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + + port { + etm1_out: endpoint { + remote-endpoint = + <&cluster0_funnel_in_port1>; + }; + }; + }; + + etm@11640000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x11640000 0 0x1000>; + cpu = <&CPU2>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + + port { + etm2_out: endpoint { + remote-endpoint = + <&cluster0_funnel_in_port2>; + }; + }; + }; + + etm@11740000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x11740000 0 0x1000>; + cpu = <&CPU3>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + + port { + etm3_out: endpoint { + remote-endpoint = + <&cluster0_funnel_in_port3>; + }; + }; + }; + + etm@11840000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x11840000 0 0x1000>; + cpu = <&CPU4>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + + port { + etm4_out: endpoint { + remote-endpoint = + <&cluster1_funnel_in_port0>; + }; + }; + }; + + etm@11940000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x11940000 0 0x1000>; + cpu = <&CPU5>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + + port { + etm5_out: endpoint { + remote-endpoint = + <&cluster1_funnel_in_port1>; + }; + }; + }; + + etm@11a40000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x11a40000 0 0x1000>; + cpu = <&CPU6>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + + port { + etm6_out: endpoint { + remote-endpoint = + <&cluster1_funnel_in_port2>; + }; + }; + }; + + etm@11b40000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x11b40000 0 0x1000>; + cpu = <&CPU7>; + clocks = <&ext_26m>; + clock-names = "apb_pclk"; + + port { + etm7_out: endpoint { + remote-endpoint = + <&cluster1_funnel_in_port3>; + }; + }; + }; + }; +}; diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts new file mode 100644 index 000000000000..ae0b28ce6319 --- /dev/null +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts @@ -0,0 +1,56 @@ +/* + * Spreadtrum SP9860g board + * + * Copyright (C) 2017, Spreadtrum Communications Inc. + * + * SPDX-License-Identifier: (GPL-2.0+ OR MIT) + */ + +/dts-v1/; + +#include "sc9860.dtsi" + +/ { + model = "Spreadtrum SP9860G 3GFHD Board"; + + compatible = "sprd,sp9860g-1h10", "sprd,sc9860"; + + aliases { + serial0 = &uart0; /* for Bluetooth */ + serial1 = &uart1; /* UART console */ + serial2 = &uart2; /* Reserved */ + serial3 = &uart3; /* for GPS */ + }; + + memory{ + device_type = "memory"; + reg = <0x0 0x80000000 0 0x60000000>, + <0x1 0x80000000 0 0x60000000>; + }; + + chosen { + stdout-path = "serial1:115200n8"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + }; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi new file mode 100644 index 000000000000..7c217c547f85 --- /dev/null +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi @@ -0,0 +1,71 @@ +/* + * Spreadtrum Whale2 platform peripherals + * + * Copyright (C) 2016, Spreadtrum Communications Inc. + * + * SPDX-License-Identifier: (GPL-2.0+ OR MIT) + */ + +/ { + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + soc: soc { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + ap-apb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0 0x70000000 0x10000000>; + + uart0: serial@0 { + compatible = "sprd,sc9860-uart", + "sprd,sc9836-uart"; + reg = <0x0 0x100>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ext_26m>; + status = "disabled"; + }; + + uart1: serial@100000 { + compatible = "sprd,sc9860-uart", + "sprd,sc9836-uart"; + reg = <0x100000 0x100>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ext_26m>; + status = "disabled"; + }; + + uart2: serial@200000 { + compatible = "sprd,sc9860-uart", + "sprd,sc9836-uart"; + reg = <0x200000 0x100>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ext_26m>; + status = "disabled"; + }; + + uart3: serial@300000 { + compatible = "sprd,sc9860-uart", + "sprd,sc9836-uart"; + reg = <0x300000 0x100>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ext_26m>; + status = "disabled"; + }; + }; + + }; + + ext_26m: ext-26m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; + clock-output-names = "ext_26m"; + }; +}; diff --git a/arch/arm64/boot/dts/zte/zx296718-evb.dts b/arch/arm64/boot/dts/zte/zx296718-evb.dts index e164ff6de5fc..bb900d2bbcfb 100644 --- a/arch/arm64/boot/dts/zte/zx296718-evb.dts +++ b/arch/arm64/boot/dts/zte/zx296718-evb.dts @@ -57,6 +57,34 @@ reg = <0x40000000 0x40000000>; }; + sound0 { + compatible = "simple-audio-card"; + simple-audio-card,name = "zx_snd_spdif0"; + + simple-audio-card,cpu { + sound-dai = <&spdif0>; + }; + + simple-audio-card,codec { + sound-dai = <&hdmi>; + }; + }; +}; + +&emmc { + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&sd1 { + status = "okay"; +}; + +&spdif0 { + status = "okay"; }; &uart0 { diff --git a/arch/arm64/boot/dts/zte/zx296718.dtsi b/arch/arm64/boot/dts/zte/zx296718.dtsi index b850b2cd0adc..316dc713268c 100644 --- a/arch/arm64/boot/dts/zte/zx296718.dtsi +++ b/arch/arm64/boot/dts/zte/zx296718.dtsi @@ -235,13 +235,6 @@ clock-output-names = "pll_mac"; }; - pll_vga: clk-pll-1073m { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <1073000000>; - clock-output-names = "pll_vga"; - }; - pll_mm0: clk-pll-1188m { compatible = "fixed-clock"; #clock-cells = <0>; @@ -305,6 +298,51 @@ status = "disabled"; }; + sd0: mmc@1110000 { + compatible = "zte,zx296718-dw-mshc"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x01110000 0x1000>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + fifo-depth = <32>; + data-addr = <0x200>; + fifo-watermark-aligned; + bus-width = <4>; + clock-frequency = <50000000>; + clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>; + clock-names = "biu", "ciu"; + num-slots = <1>; + max-frequency = <50000000>; + cap-sdio-irq; + cap-sd-highspeed; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + sd-uhs-sdr104; + sd-uhs-ddr50; + status = "disabled"; + }; + + sd1: mmc@1111000 { + compatible = "zte,zx296718-dw-mshc"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x01111000 0x1000>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + fifo-depth = <32>; + data-addr = <0x200>; + fifo-watermark-aligned; + bus-width = <4>; + clock-frequency = <167000000>; + clocks = <&topcrm SD1_AHB>, <&topcrm SD1_WCLK>; + clock-names = "biu", "ciu"; + num-slots = <1>; + max-frequency = <167000000>; + cap-sdio-irq; + cap-sd-highspeed; + status = "disabled"; + }; + dma: dma-controller@1460000 { compatible = "zte,zx296702-dma"; reg = <0x01460000 0x1000>; @@ -328,6 +366,47 @@ #clock-cells = <1>; }; + vou: vou@1440000 { + compatible = "zte,zx296718-vou"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1440000 0x10000>; + + dpc: dpc@0 { + compatible = "zte,zx296718-dpc"; + reg = <0x0000 0x1000>, <0x1000 0x1000>, + <0x5000 0x1000>, <0x6000 0x1000>, + <0xa000 0x1000>; + reg-names = "osd", "timing_ctrl", + "dtrc", "vou_ctrl", + "otfppu"; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topcrm VOU_ACLK>, <&topcrm VOU_PPU_WCLK>, + <&topcrm VOU_MAIN_WCLK>, <&topcrm VOU_AUX_WCLK>; + clock-names = "aclk", "ppu_wclk", + "main_wclk", "aux_wclk"; + }; + + hdmi: hdmi@c000 { + compatible = "zte,zx296718-hdmi"; + reg = <0xc000 0x4000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_EDGE_RISING>; + clocks = <&topcrm HDMI_OSC_CEC>, + <&topcrm HDMI_OSC_CLK>, + <&topcrm HDMI_XCLK>; + clock-names = "osc_cec", "osc_clk", "xclk"; + #sound-dai-cells = <0>; + status = "disabled"; + }; + + tvenc: tvenc@2000 { + compatible = "zte,zx296718-tvenc"; + reg = <0x2000 0x1000>; + zte,tvenc-power-control = <&sysctrl 0x170 0x10>; + status = "disabled"; + }; + }; + topcrm: clock-controller@1461000 { compatible = "zte,zx296718-topcrm"; reg = <0x01461000 0x1000>; @@ -339,10 +418,43 @@ reg = <0x1463000 0x1000>; }; + emmc: mmc@1470000{ + compatible = "zte,zx296718-dw-mshc"; + reg = <0x01470000 0x1000>; + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; + zte,aon-syscon = <&aon_sysctrl>; + bus-width = <8>; + fifo-depth = <128>; + data-addr = <0x200>; + fifo-watermark-aligned; + clock-frequency = <167000000>; + clocks = <&topcrm EMMC_NAND_AHB>, <&topcrm EMMC_WCLK>; + clock-names = "biu", "ciu"; + max-frequency = <167000000>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + non-removable; + disable-wp; + status = "disabled"; + }; + audiocrm: clock-controller@1480000 { compatible = "zte,zx296718-audiocrm"; reg = <0x01480000 0x1000>; #clock-cells = <1>; }; + + spdif0: spdif@1488000 { + compatible = "zte,zx296702-spdif"; + reg = <0x1488000 0x1000>; + clocks = <&audiocrm AUDIO_SPDIF0_WCLK>; + clock-names = "tx"; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + #sound-dai-cells = <0>; + dmas = <&dma 30>; + dma-names = "tx"; + status = "disabled"; + }; }; }; diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index 7c48028ec64a..ce072859e3b2 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -82,6 +82,7 @@ CONFIG_CMA=y CONFIG_SECCOMP=y CONFIG_XEN=y CONFIG_KEXEC=y +CONFIG_CRASH_DUMP=y # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set CONFIG_COMPAT=y CONFIG_CPU_IDLE=y @@ -185,6 +186,8 @@ CONFIG_HNS_ENET=y CONFIG_E1000E=y CONFIG_IGB=y CONFIG_IGBVF=y +CONFIG_MVPP2=y +CONFIG_MVNETA=y CONFIG_SKY2=y CONFIG_RAVB=y CONFIG_SMC91X=y @@ -249,8 +252,10 @@ CONFIG_I2C_DESIGNWARE_PLATFORM=y CONFIG_I2C_IMX=y CONFIG_I2C_MESON=y CONFIG_I2C_MV64XXX=y +CONFIG_I2C_PXA=y CONFIG_I2C_QUP=y CONFIG_I2C_RK3X=y +CONFIG_I2C_SH_MOBILE=y CONFIG_I2C_TEGRA=y CONFIG_I2C_UNIPHIER_F=y CONFIG_I2C_RCAR=y @@ -299,6 +304,7 @@ CONFIG_RENESAS_WDT=y CONFIG_S3C2410_WATCHDOG=y CONFIG_MESON_GXBB_WATCHDOG=m CONFIG_MESON_WATCHDOG=m +CONFIG_MFD_EXYNOS_LPASS=m CONFIG_MFD_MAX77620=y CONFIG_MFD_RK808=y CONFIG_MFD_SPMI_PMIC=y @@ -324,10 +330,20 @@ CONFIG_MEDIA_CONTROLLER=y CONFIG_VIDEO_V4L2_SUBDEV_API=y # CONFIG_DVB_NET is not set CONFIG_V4L_MEM2MEM_DRIVERS=y +CONFIG_VIDEO_SAMSUNG_S5P_JPEG=m +CONFIG_VIDEO_SAMSUNG_S5P_MFC=m +CONFIG_VIDEO_SAMSUNG_EXYNOS_GSC=m CONFIG_VIDEO_RENESAS_FCP=m CONFIG_VIDEO_RENESAS_VSP1=m CONFIG_DRM=m CONFIG_DRM_NOUVEAU=m +CONFIG_DRM_EXYNOS=m +CONFIG_DRM_EXYNOS5433_DECON=y +CONFIG_DRM_EXYNOS7_DECON=y +CONFIG_DRM_EXYNOS_DSI=y +# CONFIG_DRM_EXYNOS_DP is not set +CONFIG_DRM_EXYNOS_HDMI=y +CONFIG_DRM_EXYNOS_MIC=y CONFIG_DRM_RCAR_DU=m CONFIG_DRM_RCAR_HDMI=y CONFIG_DRM_RCAR_LVDS=y @@ -398,11 +414,15 @@ CONFIG_MMC_DW_EXYNOS=y CONFIG_MMC_DW_K3=y CONFIG_MMC_DW_ROCKCHIP=y CONFIG_MMC_SUNXI=y +CONFIG_MMC_SDHCI_XENON=y +CONFIG_MMC_BCM2835=y CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=y CONFIG_LEDS_GPIO=y +CONFIG_LEDS_PWM=y CONFIG_LEDS_SYSCON=y CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_DEFAULT_ON=y CONFIG_LEDS_TRIGGER_HEARTBEAT=y CONFIG_LEDS_TRIGGER_CPU=y CONFIG_RTC_CLASS=y @@ -469,6 +489,7 @@ CONFIG_PHY_RCAR_GEN3_USB2=y CONFIG_PHY_HI6220_USB=y CONFIG_PHY_ROCKCHIP_INNO_USB2=y CONFIG_PHY_ROCKCHIP_EMMC=y +CONFIG_PHY_SUN4I_USB=y CONFIG_PHY_XGENE=y CONFIG_PHY_TEGRA_XUSB=y CONFIG_ARM_SCPI_PROTOCOL=y @@ -518,6 +539,7 @@ CONFIG_MEMTEST=y CONFIG_SECURITY=y CONFIG_CRYPTO_ECHAINIV=y CONFIG_CRYPTO_ANSI_CPRNG=y +CONFIG_CRYPTO_DEV_SAFEXCEL=m CONFIG_ARM64_CRYPTO=y CONFIG_CRYPTO_SHA1_ARM64_CE=y CONFIG_CRYPTO_SHA2_ARM64_CE=y diff --git a/arch/arm64/include/asm/Kbuild b/arch/arm64/include/asm/Kbuild index a12f1afc95a3..a7a97a608033 100644 --- a/arch/arm64/include/asm/Kbuild +++ b/arch/arm64/include/asm/Kbuild @@ -29,6 +29,7 @@ generic-y += rwsem.h generic-y += segment.h generic-y += sembuf.h generic-y += serial.h +generic-y += set_memory.h generic-y += shmbuf.h generic-y += simd.h generic-y += sizes.h diff --git a/arch/arm64/include/asm/acpi.h b/arch/arm64/include/asm/acpi.h index c1976c0adca7..0e99978da3f0 100644 --- a/arch/arm64/include/asm/acpi.h +++ b/arch/arm64/include/asm/acpi.h @@ -85,6 +85,8 @@ static inline bool acpi_has_cpu_in_madt(void) return true; } +struct acpi_madt_generic_interrupt *acpi_cpu_get_madt_gicc(int cpu); + static inline void arch_fix_phys_package_id(int num, u32 slot) { } void __init acpi_init_cpus(void); diff --git a/arch/arm64/include/asm/arch_gicv3.h b/arch/arm64/include/asm/arch_gicv3.h index f37e3a21f6e7..1a98bc8602a2 100644 --- a/arch/arm64/include/asm/arch_gicv3.h +++ b/arch/arm64/include/asm/arch_gicv3.h @@ -20,69 +20,14 @@ #include <asm/sysreg.h> -#define ICC_EOIR1_EL1 sys_reg(3, 0, 12, 12, 1) -#define ICC_DIR_EL1 sys_reg(3, 0, 12, 11, 1) -#define ICC_IAR1_EL1 sys_reg(3, 0, 12, 12, 0) -#define ICC_SGI1R_EL1 sys_reg(3, 0, 12, 11, 5) -#define ICC_PMR_EL1 sys_reg(3, 0, 4, 6, 0) -#define ICC_CTLR_EL1 sys_reg(3, 0, 12, 12, 4) -#define ICC_SRE_EL1 sys_reg(3, 0, 12, 12, 5) -#define ICC_GRPEN1_EL1 sys_reg(3, 0, 12, 12, 7) -#define ICC_BPR1_EL1 sys_reg(3, 0, 12, 12, 3) - -#define ICC_SRE_EL2 sys_reg(3, 4, 12, 9, 5) - -/* - * System register definitions - */ -#define ICH_VSEIR_EL2 sys_reg(3, 4, 12, 9, 4) -#define ICH_HCR_EL2 sys_reg(3, 4, 12, 11, 0) -#define ICH_VTR_EL2 sys_reg(3, 4, 12, 11, 1) -#define ICH_MISR_EL2 sys_reg(3, 4, 12, 11, 2) -#define ICH_EISR_EL2 sys_reg(3, 4, 12, 11, 3) -#define ICH_ELSR_EL2 sys_reg(3, 4, 12, 11, 5) -#define ICH_VMCR_EL2 sys_reg(3, 4, 12, 11, 7) - -#define __LR0_EL2(x) sys_reg(3, 4, 12, 12, x) -#define __LR8_EL2(x) sys_reg(3, 4, 12, 13, x) - -#define ICH_LR0_EL2 __LR0_EL2(0) -#define ICH_LR1_EL2 __LR0_EL2(1) -#define ICH_LR2_EL2 __LR0_EL2(2) -#define ICH_LR3_EL2 __LR0_EL2(3) -#define ICH_LR4_EL2 __LR0_EL2(4) -#define ICH_LR5_EL2 __LR0_EL2(5) -#define ICH_LR6_EL2 __LR0_EL2(6) -#define ICH_LR7_EL2 __LR0_EL2(7) -#define ICH_LR8_EL2 __LR8_EL2(0) -#define ICH_LR9_EL2 __LR8_EL2(1) -#define ICH_LR10_EL2 __LR8_EL2(2) -#define ICH_LR11_EL2 __LR8_EL2(3) -#define ICH_LR12_EL2 __LR8_EL2(4) -#define ICH_LR13_EL2 __LR8_EL2(5) -#define ICH_LR14_EL2 __LR8_EL2(6) -#define ICH_LR15_EL2 __LR8_EL2(7) - -#define __AP0Rx_EL2(x) sys_reg(3, 4, 12, 8, x) -#define ICH_AP0R0_EL2 __AP0Rx_EL2(0) -#define ICH_AP0R1_EL2 __AP0Rx_EL2(1) -#define ICH_AP0R2_EL2 __AP0Rx_EL2(2) -#define ICH_AP0R3_EL2 __AP0Rx_EL2(3) - -#define __AP1Rx_EL2(x) sys_reg(3, 4, 12, 9, x) -#define ICH_AP1R0_EL2 __AP1Rx_EL2(0) -#define ICH_AP1R1_EL2 __AP1Rx_EL2(1) -#define ICH_AP1R2_EL2 __AP1Rx_EL2(2) -#define ICH_AP1R3_EL2 __AP1Rx_EL2(3) - #ifndef __ASSEMBLY__ #include <linux/stringify.h> #include <asm/barrier.h> #include <asm/cacheflush.h> -#define read_gicreg read_sysreg_s -#define write_gicreg write_sysreg_s +#define read_gicreg(r) read_sysreg_s(SYS_ ## r) +#define write_gicreg(v, r) write_sysreg_s(v, SYS_ ## r) /* * Low-level accessors @@ -93,13 +38,13 @@ static inline void gic_write_eoir(u32 irq) { - write_sysreg_s(irq, ICC_EOIR1_EL1); + write_sysreg_s(irq, SYS_ICC_EOIR1_EL1); isb(); } static inline void gic_write_dir(u32 irq) { - write_sysreg_s(irq, ICC_DIR_EL1); + write_sysreg_s(irq, SYS_ICC_DIR_EL1); isb(); } @@ -107,7 +52,7 @@ static inline u64 gic_read_iar_common(void) { u64 irqstat; - irqstat = read_sysreg_s(ICC_IAR1_EL1); + irqstat = read_sysreg_s(SYS_ICC_IAR1_EL1); dsb(sy); return irqstat; } @@ -124,7 +69,7 @@ static inline u64 gic_read_iar_cavium_thunderx(void) u64 irqstat; nops(8); - irqstat = read_sysreg_s(ICC_IAR1_EL1); + irqstat = read_sysreg_s(SYS_ICC_IAR1_EL1); nops(4); mb(); @@ -133,40 +78,40 @@ static inline u64 gic_read_iar_cavium_thunderx(void) static inline void gic_write_pmr(u32 val) { - write_sysreg_s(val, ICC_PMR_EL1); + write_sysreg_s(val, SYS_ICC_PMR_EL1); } static inline void gic_write_ctlr(u32 val) { - write_sysreg_s(val, ICC_CTLR_EL1); + write_sysreg_s(val, SYS_ICC_CTLR_EL1); isb(); } static inline void gic_write_grpen1(u32 val) { - write_sysreg_s(val, ICC_GRPEN1_EL1); + write_sysreg_s(val, SYS_ICC_GRPEN1_EL1); isb(); } static inline void gic_write_sgi1r(u64 val) { - write_sysreg_s(val, ICC_SGI1R_EL1); + write_sysreg_s(val, SYS_ICC_SGI1R_EL1); } static inline u32 gic_read_sre(void) { - return read_sysreg_s(ICC_SRE_EL1); + return read_sysreg_s(SYS_ICC_SRE_EL1); } static inline void gic_write_sre(u32 val) { - write_sysreg_s(val, ICC_SRE_EL1); + write_sysreg_s(val, SYS_ICC_SRE_EL1); isb(); } static inline void gic_write_bpr1(u32 val) { - asm volatile("msr_s " __stringify(ICC_BPR1_EL1) ", %0" : : "r" (val)); + write_sysreg_s(val, SYS_ICC_BPR1_EL1); } #define gic_read_typer(c) readq_relaxed(c) diff --git a/arch/arm64/include/asm/asm-uaccess.h b/arch/arm64/include/asm/asm-uaccess.h index df411f3e083c..ecd9788cd298 100644 --- a/arch/arm64/include/asm/asm-uaccess.h +++ b/arch/arm64/include/asm/asm-uaccess.h @@ -62,4 +62,13 @@ alternative_if ARM64_ALT_PAN_NOT_UAO alternative_else_nop_endif .endm +/* + * Remove the address tag from a virtual address, if present. + */ + .macro clear_address_tag, dst, addr + tst \addr, #(1 << 55) + bic \dst, \addr, #(0xff << 56) + csel \dst, \dst, \addr, eq + .endm + #endif diff --git a/arch/arm64/include/asm/atomic_lse.h b/arch/arm64/include/asm/atomic_lse.h index 7457ce082b5f..99fa69c9c3cf 100644 --- a/arch/arm64/include/asm/atomic_lse.h +++ b/arch/arm64/include/asm/atomic_lse.h @@ -322,7 +322,7 @@ static inline void atomic64_and(long i, atomic64_t *v) #define ATOMIC64_FETCH_OP_AND(name, mb, cl...) \ static inline long atomic64_fetch_and##name(long i, atomic64_t *v) \ { \ - register long x0 asm ("w0") = i; \ + register long x0 asm ("x0") = i; \ register atomic64_t *x1 asm ("x1") = v; \ \ asm volatile(ARM64_LSE_ATOMIC_INSN( \ @@ -394,7 +394,7 @@ ATOMIC64_OP_SUB_RETURN( , al, "memory") #define ATOMIC64_FETCH_OP_SUB(name, mb, cl...) \ static inline long atomic64_fetch_sub##name(long i, atomic64_t *v) \ { \ - register long x0 asm ("w0") = i; \ + register long x0 asm ("x0") = i; \ register atomic64_t *x1 asm ("x1") = v; \ \ asm volatile(ARM64_LSE_ATOMIC_INSN( \ diff --git a/arch/arm64/include/asm/barrier.h b/arch/arm64/include/asm/barrier.h index 4e0497f581a0..0fe7e43b7fbc 100644 --- a/arch/arm64/include/asm/barrier.h +++ b/arch/arm64/include/asm/barrier.h @@ -42,25 +42,35 @@ #define __smp_rmb() dmb(ishld) #define __smp_wmb() dmb(ishst) -#define __smp_store_release(p, v) \ +#define __smp_store_release(p, v) \ do { \ + union { typeof(*p) __val; char __c[1]; } __u = \ + { .__val = (__force typeof(*p)) (v) }; \ compiletime_assert_atomic_type(*p); \ switch (sizeof(*p)) { \ case 1: \ asm volatile ("stlrb %w1, %0" \ - : "=Q" (*p) : "r" (v) : "memory"); \ + : "=Q" (*p) \ + : "r" (*(__u8 *)__u.__c) \ + : "memory"); \ break; \ case 2: \ asm volatile ("stlrh %w1, %0" \ - : "=Q" (*p) : "r" (v) : "memory"); \ + : "=Q" (*p) \ + : "r" (*(__u16 *)__u.__c) \ + : "memory"); \ break; \ case 4: \ asm volatile ("stlr %w1, %0" \ - : "=Q" (*p) : "r" (v) : "memory"); \ + : "=Q" (*p) \ + : "r" (*(__u32 *)__u.__c) \ + : "memory"); \ break; \ case 8: \ asm volatile ("stlr %1, %0" \ - : "=Q" (*p) : "r" (v) : "memory"); \ + : "=Q" (*p) \ + : "r" (*(__u64 *)__u.__c) \ + : "memory"); \ break; \ } \ } while (0) diff --git a/arch/arm64/include/asm/bug.h b/arch/arm64/include/asm/bug.h index a9be1072933c..366448eb0fb7 100644 --- a/arch/arm64/include/asm/bug.h +++ b/arch/arm64/include/asm/bug.h @@ -20,9 +20,6 @@ #include <asm/brk-imm.h> -#ifdef CONFIG_GENERIC_BUG -#define HAVE_ARCH_BUG - #ifdef CONFIG_DEBUG_BUGVERBOSE #define _BUGVERBOSE_LOCATION(file, line) __BUGVERBOSE_LOCATION(file, line) #define __BUGVERBOSE_LOCATION(file, line) \ @@ -36,28 +33,35 @@ #define _BUGVERBOSE_LOCATION(file, line) #endif -#define _BUG_FLAGS(flags) __BUG_FLAGS(flags) +#ifdef CONFIG_GENERIC_BUG -#define __BUG_FLAGS(flags) asm volatile ( \ +#define __BUG_ENTRY(flags) \ ".pushsection __bug_table,\"a\"\n\t" \ ".align 2\n\t" \ "0: .long 1f - 0b\n\t" \ _BUGVERBOSE_LOCATION(__FILE__, __LINE__) \ ".short " #flags "\n\t" \ ".popsection\n" \ - \ - "1: brk %[imm]" \ - :: [imm] "i" (BUG_BRK_IMM) \ -) + "1: " +#else +#define __BUG_ENTRY(flags) "" +#endif + +#define __BUG_FLAGS(flags) \ + asm volatile ( \ + __BUG_ENTRY(flags) \ + "brk %[imm]" :: [imm] "i" (BUG_BRK_IMM) \ + ); -#define BUG() do { \ - _BUG_FLAGS(0); \ - unreachable(); \ + +#define BUG() do { \ + __BUG_FLAGS(0); \ + unreachable(); \ } while (0) -#define __WARN_FLAGS(flags) _BUG_FLAGS(BUGFLAG_WARNING|(flags)) +#define __WARN_FLAGS(flags) __BUG_FLAGS(BUGFLAG_WARNING|(flags)) -#endif /* ! CONFIG_GENERIC_BUG */ +#define HAVE_ARCH_BUG #include <asm-generic/bug.h> diff --git a/arch/arm64/include/asm/cache.h b/arch/arm64/include/asm/cache.h index 5082b30bc2c0..ea9bb4e0e9bb 100644 --- a/arch/arm64/include/asm/cache.h +++ b/arch/arm64/include/asm/cache.h @@ -16,7 +16,18 @@ #ifndef __ASM_CACHE_H #define __ASM_CACHE_H -#include <asm/cachetype.h> +#include <asm/cputype.h> + +#define CTR_L1IP_SHIFT 14 +#define CTR_L1IP_MASK 3 +#define CTR_CWG_SHIFT 24 +#define CTR_CWG_MASK 15 + +#define CTR_L1IP(ctr) (((ctr) >> CTR_L1IP_SHIFT) & CTR_L1IP_MASK) + +#define ICACHE_POLICY_VPIPT 0 +#define ICACHE_POLICY_VIPT 2 +#define ICACHE_POLICY_PIPT 3 #define L1_CACHE_SHIFT 7 #define L1_CACHE_BYTES (1 << L1_CACHE_SHIFT) @@ -32,6 +43,31 @@ #ifndef __ASSEMBLY__ +#include <linux/bitops.h> + +#define ICACHEF_ALIASING 0 +#define ICACHEF_VPIPT 1 +extern unsigned long __icache_flags; + +/* + * Whilst the D-side always behaves as PIPT on AArch64, aliasing is + * permitted in the I-cache. + */ +static inline int icache_is_aliasing(void) +{ + return test_bit(ICACHEF_ALIASING, &__icache_flags); +} + +static inline int icache_is_vpipt(void) +{ + return test_bit(ICACHEF_VPIPT, &__icache_flags); +} + +static inline u32 cache_type_cwg(void) +{ + return (read_cpuid_cachetype() >> CTR_CWG_SHIFT) & CTR_CWG_MASK; +} + #define __read_mostly __attribute__((__section__(".data..read_mostly"))) static inline int cache_line_size(void) diff --git a/arch/arm64/include/asm/cacheflush.h b/arch/arm64/include/asm/cacheflush.h index 5a2a6ee65f65..d74a284abdc2 100644 --- a/arch/arm64/include/asm/cacheflush.h +++ b/arch/arm64/include/asm/cacheflush.h @@ -150,9 +150,6 @@ static inline void flush_cache_vunmap(unsigned long start, unsigned long end) { } -int set_memory_ro(unsigned long addr, int numpages); -int set_memory_rw(unsigned long addr, int numpages); -int set_memory_x(unsigned long addr, int numpages); -int set_memory_nx(unsigned long addr, int numpages); +int set_memory_valid(unsigned long addr, unsigned long size, int enable); #endif diff --git a/arch/arm64/include/asm/cachetype.h b/arch/arm64/include/asm/cachetype.h deleted file mode 100644 index f5588692f1d4..000000000000 --- a/arch/arm64/include/asm/cachetype.h +++ /dev/null @@ -1,100 +0,0 @@ -/* - * Copyright (C) 2012 ARM Ltd. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see <http://www.gnu.org/licenses/>. - */ -#ifndef __ASM_CACHETYPE_H -#define __ASM_CACHETYPE_H - -#include <asm/cputype.h> - -#define CTR_L1IP_SHIFT 14 -#define CTR_L1IP_MASK 3 -#define CTR_CWG_SHIFT 24 -#define CTR_CWG_MASK 15 - -#define ICACHE_POLICY_RESERVED 0 -#define ICACHE_POLICY_AIVIVT 1 -#define ICACHE_POLICY_VIPT 2 -#define ICACHE_POLICY_PIPT 3 - -#ifndef __ASSEMBLY__ - -#include <linux/bitops.h> - -#define CTR_L1IP(ctr) (((ctr) >> CTR_L1IP_SHIFT) & CTR_L1IP_MASK) - -#define ICACHEF_ALIASING 0 -#define ICACHEF_AIVIVT 1 - -extern unsigned long __icache_flags; - -/* - * NumSets, bits[27:13] - (Number of sets in cache) - 1 - * Associativity, bits[12:3] - (Associativity of cache) - 1 - * LineSize, bits[2:0] - (Log2(Number of words in cache line)) - 2 - */ -#define CCSIDR_EL1_WRITE_THROUGH BIT(31) -#define CCSIDR_EL1_WRITE_BACK BIT(30) -#define CCSIDR_EL1_READ_ALLOCATE BIT(29) -#define CCSIDR_EL1_WRITE_ALLOCATE BIT(28) -#define CCSIDR_EL1_LINESIZE_MASK 0x7 -#define CCSIDR_EL1_LINESIZE(x) ((x) & CCSIDR_EL1_LINESIZE_MASK) -#define CCSIDR_EL1_ASSOCIATIVITY_SHIFT 3 -#define CCSIDR_EL1_ASSOCIATIVITY_MASK 0x3ff -#define CCSIDR_EL1_ASSOCIATIVITY(x) \ - (((x) >> CCSIDR_EL1_ASSOCIATIVITY_SHIFT) & CCSIDR_EL1_ASSOCIATIVITY_MASK) -#define CCSIDR_EL1_NUMSETS_SHIFT 13 -#define CCSIDR_EL1_NUMSETS_MASK 0x7fff -#define CCSIDR_EL1_NUMSETS(x) \ - (((x) >> CCSIDR_EL1_NUMSETS_SHIFT) & CCSIDR_EL1_NUMSETS_MASK) - -#define CACHE_LINESIZE(x) (16 << CCSIDR_EL1_LINESIZE(x)) -#define CACHE_NUMSETS(x) (CCSIDR_EL1_NUMSETS(x) + 1) -#define CACHE_ASSOCIATIVITY(x) (CCSIDR_EL1_ASSOCIATIVITY(x) + 1) - -extern u64 __attribute_const__ cache_get_ccsidr(u64 csselr); - -/* Helpers for Level 1 Instruction cache csselr = 1L */ -static inline int icache_get_linesize(void) -{ - return CACHE_LINESIZE(cache_get_ccsidr(1L)); -} - -static inline int icache_get_numsets(void) -{ - return CACHE_NUMSETS(cache_get_ccsidr(1L)); -} - -/* - * Whilst the D-side always behaves as PIPT on AArch64, aliasing is - * permitted in the I-cache. - */ -static inline int icache_is_aliasing(void) -{ - return test_bit(ICACHEF_ALIASING, &__icache_flags); -} - -static inline int icache_is_aivivt(void) -{ - return test_bit(ICACHEF_AIVIVT, &__icache_flags); -} - -static inline u32 cache_type_cwg(void) -{ - return (read_cpuid_cachetype() >> CTR_CWG_SHIFT) & CTR_CWG_MASK; -} - -#endif /* __ASSEMBLY__ */ - -#endif /* __ASM_CACHETYPE_H */ diff --git a/arch/arm64/include/asm/cmpxchg.h b/arch/arm64/include/asm/cmpxchg.h index 91b26d26af8a..ae852add053d 100644 --- a/arch/arm64/include/asm/cmpxchg.h +++ b/arch/arm64/include/asm/cmpxchg.h @@ -46,7 +46,7 @@ static inline unsigned long __xchg_case_##name(unsigned long x, \ " swp" #acq_lse #rel #sz "\t%" #w "3, %" #w "0, %2\n" \ __nops(3) \ " " #nop_lse) \ - : "=&r" (ret), "=&r" (tmp), "+Q" (*(u8 *)ptr) \ + : "=&r" (ret), "=&r" (tmp), "+Q" (*(unsigned long *)ptr) \ : "r" (x) \ : cl); \ \ diff --git a/arch/arm64/include/asm/cpufeature.h b/arch/arm64/include/asm/cpufeature.h index f31c48d0cd68..e7f84a7b4465 100644 --- a/arch/arm64/include/asm/cpufeature.h +++ b/arch/arm64/include/asm/cpufeature.h @@ -226,7 +226,7 @@ void update_cpu_errata_workarounds(void); void __init enable_errata_workarounds(void); void verify_local_cpu_errata_workarounds(void); -u64 read_system_reg(u32 id); +u64 read_sanitised_ftr_reg(u32 id); static inline bool cpu_supports_mixed_endian_el0(void) { @@ -240,7 +240,7 @@ static inline bool system_supports_32bit_el0(void) static inline bool system_supports_mixed_endian_el0(void) { - return id_aa64mmfr0_mixed_endian_el0(read_system_reg(SYS_ID_AA64MMFR0_EL1)); + return id_aa64mmfr0_mixed_endian_el0(read_sanitised_ftr_reg(SYS_ID_AA64MMFR0_EL1)); } static inline bool system_supports_fpsimd(void) diff --git a/arch/arm64/include/asm/esr.h b/arch/arm64/include/asm/esr.h index ad42e79a5d4d..85997c0e5443 100644 --- a/arch/arm64/include/asm/esr.h +++ b/arch/arm64/include/asm/esr.h @@ -177,6 +177,10 @@ #define ESR_ELx_SYS64_ISS_SYS_CNTVCT (ESR_ELx_SYS64_ISS_SYS_VAL(3, 3, 2, 14, 0) | \ ESR_ELx_SYS64_ISS_DIR_READ) + +#define ESR_ELx_SYS64_ISS_SYS_CNTFRQ (ESR_ELx_SYS64_ISS_SYS_VAL(3, 3, 0, 14, 0) | \ + ESR_ELx_SYS64_ISS_DIR_READ) + #ifndef __ASSEMBLY__ #include <asm/types.h> diff --git a/arch/arm64/include/asm/hardirq.h b/arch/arm64/include/asm/hardirq.h index 8740297dac77..1473fc2f7ab7 100644 --- a/arch/arm64/include/asm/hardirq.h +++ b/arch/arm64/include/asm/hardirq.h @@ -20,7 +20,7 @@ #include <linux/threads.h> #include <asm/irq.h> -#define NR_IPI 6 +#define NR_IPI 7 typedef struct { unsigned int __softirq_pending; diff --git a/arch/arm64/include/asm/hw_breakpoint.h b/arch/arm64/include/asm/hw_breakpoint.h index b6b167ac082b..41770766d964 100644 --- a/arch/arm64/include/asm/hw_breakpoint.h +++ b/arch/arm64/include/asm/hw_breakpoint.h @@ -149,7 +149,7 @@ static inline void ptrace_hw_copy_thread(struct task_struct *task) /* Determine number of BRP registers available. */ static inline int get_num_brps(void) { - u64 dfr0 = read_system_reg(SYS_ID_AA64DFR0_EL1); + u64 dfr0 = read_sanitised_ftr_reg(SYS_ID_AA64DFR0_EL1); return 1 + cpuid_feature_extract_unsigned_field(dfr0, ID_AA64DFR0_BRPS_SHIFT); @@ -158,7 +158,7 @@ static inline int get_num_brps(void) /* Determine number of WRP registers available. */ static inline int get_num_wrps(void) { - u64 dfr0 = read_system_reg(SYS_ID_AA64DFR0_EL1); + u64 dfr0 = read_sanitised_ftr_reg(SYS_ID_AA64DFR0_EL1); return 1 + cpuid_feature_extract_unsigned_field(dfr0, ID_AA64DFR0_WRPS_SHIFT); diff --git a/arch/arm64/include/asm/insn.h b/arch/arm64/include/asm/insn.h index aecc07e09a18..29cb2ca756f6 100644 --- a/arch/arm64/include/asm/insn.h +++ b/arch/arm64/include/asm/insn.h @@ -80,6 +80,7 @@ enum aarch64_insn_register_type { AARCH64_INSN_REGTYPE_RM, AARCH64_INSN_REGTYPE_RD, AARCH64_INSN_REGTYPE_RA, + AARCH64_INSN_REGTYPE_RS, }; enum aarch64_insn_register { @@ -188,6 +189,8 @@ enum aarch64_insn_ldst_type { AARCH64_INSN_LDST_STORE_PAIR_PRE_INDEX, AARCH64_INSN_LDST_LOAD_PAIR_POST_INDEX, AARCH64_INSN_LDST_STORE_PAIR_POST_INDEX, + AARCH64_INSN_LDST_LOAD_EX, + AARCH64_INSN_LDST_STORE_EX, }; enum aarch64_insn_adsb_type { @@ -240,6 +243,23 @@ enum aarch64_insn_logic_type { AARCH64_INSN_LOGIC_BIC_SETFLAGS }; +enum aarch64_insn_prfm_type { + AARCH64_INSN_PRFM_TYPE_PLD, + AARCH64_INSN_PRFM_TYPE_PLI, + AARCH64_INSN_PRFM_TYPE_PST, +}; + +enum aarch64_insn_prfm_target { + AARCH64_INSN_PRFM_TARGET_L1, + AARCH64_INSN_PRFM_TARGET_L2, + AARCH64_INSN_PRFM_TARGET_L3, +}; + +enum aarch64_insn_prfm_policy { + AARCH64_INSN_PRFM_POLICY_KEEP, + AARCH64_INSN_PRFM_POLICY_STRM, +}; + #define __AARCH64_INSN_FUNCS(abbr, mask, val) \ static __always_inline bool aarch64_insn_is_##abbr(u32 code) \ { return (code & (mask)) == (val); } \ @@ -248,6 +268,7 @@ static __always_inline u32 aarch64_insn_get_##abbr##_value(void) \ __AARCH64_INSN_FUNCS(adr, 0x9F000000, 0x10000000) __AARCH64_INSN_FUNCS(adrp, 0x9F000000, 0x90000000) +__AARCH64_INSN_FUNCS(prfm, 0x3FC00000, 0x39800000) __AARCH64_INSN_FUNCS(prfm_lit, 0xFF000000, 0xD8000000) __AARCH64_INSN_FUNCS(str_reg, 0x3FE0EC00, 0x38206800) __AARCH64_INSN_FUNCS(ldr_reg, 0x3FE0EC00, 0x38606800) @@ -357,6 +378,11 @@ u32 aarch64_insn_gen_load_store_pair(enum aarch64_insn_register reg1, int offset, enum aarch64_insn_variant variant, enum aarch64_insn_ldst_type type); +u32 aarch64_insn_gen_load_store_ex(enum aarch64_insn_register reg, + enum aarch64_insn_register base, + enum aarch64_insn_register state, + enum aarch64_insn_size_type size, + enum aarch64_insn_ldst_type type); u32 aarch64_insn_gen_add_sub_imm(enum aarch64_insn_register dst, enum aarch64_insn_register src, int imm, enum aarch64_insn_variant variant, @@ -397,6 +423,10 @@ u32 aarch64_insn_gen_logical_shifted_reg(enum aarch64_insn_register dst, int shift, enum aarch64_insn_variant variant, enum aarch64_insn_logic_type type); +u32 aarch64_insn_gen_prefetch(enum aarch64_insn_register base, + enum aarch64_insn_prfm_type type, + enum aarch64_insn_prfm_target target, + enum aarch64_insn_prfm_policy policy); s32 aarch64_get_branch_offset(u32 insn); u32 aarch64_set_branch_offset(u32 insn, s32 offset); diff --git a/arch/arm64/include/asm/io.h b/arch/arm64/include/asm/io.h index 0c00c87bb9dd..35b2e50f17fb 100644 --- a/arch/arm64/include/asm/io.h +++ b/arch/arm64/include/asm/io.h @@ -173,6 +173,16 @@ extern void __iomem *ioremap_cache(phys_addr_t phys_addr, size_t size); #define iounmap __iounmap /* + * PCI configuration space mapping function. + * + * The PCI specification disallows posted write configuration transactions. + * Add an arch specific pci_remap_cfgspace() definition that is implemented + * through nGnRnE device memory attribute as recommended by the ARM v8 + * Architecture reference manual Issue A.k B2.8.2 "Device memory". + */ +#define pci_remap_cfgspace(addr, size) __ioremap((addr), (size), __pgprot(PROT_DEVICE_nGnRnE)) + +/* * io{read,write}{16,32,64}be() macros */ #define ioread16be(p) ({ __u16 __v = be16_to_cpu((__force __be16)__raw_readw(p)); __iormb(); __v; }) diff --git a/arch/arm64/include/asm/kexec.h b/arch/arm64/include/asm/kexec.h index 04744dc5fb61..e17f0529a882 100644 --- a/arch/arm64/include/asm/kexec.h +++ b/arch/arm64/include/asm/kexec.h @@ -40,9 +40,59 @@ static inline void crash_setup_regs(struct pt_regs *newregs, struct pt_regs *oldregs) { - /* Empty routine needed to avoid build errors. */ + if (oldregs) { + memcpy(newregs, oldregs, sizeof(*newregs)); + } else { + u64 tmp1, tmp2; + + __asm__ __volatile__ ( + "stp x0, x1, [%2, #16 * 0]\n" + "stp x2, x3, [%2, #16 * 1]\n" + "stp x4, x5, [%2, #16 * 2]\n" + "stp x6, x7, [%2, #16 * 3]\n" + "stp x8, x9, [%2, #16 * 4]\n" + "stp x10, x11, [%2, #16 * 5]\n" + "stp x12, x13, [%2, #16 * 6]\n" + "stp x14, x15, [%2, #16 * 7]\n" + "stp x16, x17, [%2, #16 * 8]\n" + "stp x18, x19, [%2, #16 * 9]\n" + "stp x20, x21, [%2, #16 * 10]\n" + "stp x22, x23, [%2, #16 * 11]\n" + "stp x24, x25, [%2, #16 * 12]\n" + "stp x26, x27, [%2, #16 * 13]\n" + "stp x28, x29, [%2, #16 * 14]\n" + "mov %0, sp\n" + "stp x30, %0, [%2, #16 * 15]\n" + + "/* faked current PSTATE */\n" + "mrs %0, CurrentEL\n" + "mrs %1, SPSEL\n" + "orr %0, %0, %1\n" + "mrs %1, DAIF\n" + "orr %0, %0, %1\n" + "mrs %1, NZCV\n" + "orr %0, %0, %1\n" + /* pc */ + "adr %1, 1f\n" + "1:\n" + "stp %1, %0, [%2, #16 * 16]\n" + : "=&r" (tmp1), "=&r" (tmp2) + : "r" (newregs) + : "memory" + ); + } } +#if defined(CONFIG_KEXEC_CORE) && defined(CONFIG_HIBERNATION) +extern bool crash_is_nosave(unsigned long pfn); +extern void crash_prepare_suspend(void); +extern void crash_post_resume(void); +#else +static inline bool crash_is_nosave(unsigned long pfn) {return false; } +static inline void crash_prepare_suspend(void) {} +static inline void crash_post_resume(void) {} +#endif + #endif /* __ASSEMBLY__ */ #endif diff --git a/arch/arm64/include/asm/kvm_asm.h b/arch/arm64/include/asm/kvm_asm.h index ec3553eb9349..26a64d0f9ab9 100644 --- a/arch/arm64/include/asm/kvm_asm.h +++ b/arch/arm64/include/asm/kvm_asm.h @@ -28,7 +28,7 @@ #define ARM_EXCEPTION_EL1_SERROR 1 #define ARM_EXCEPTION_TRAP 2 /* The hyp-stub will return this for any kvm_call_hyp() call */ -#define ARM_EXCEPTION_HYP_GONE 3 +#define ARM_EXCEPTION_HYP_GONE HVC_STUB_ERR #define KVM_ARM64_DEBUG_DIRTY_SHIFT 0 #define KVM_ARM64_DEBUG_DIRTY (1 << KVM_ARM64_DEBUG_DIRTY_SHIFT) @@ -47,7 +47,6 @@ struct kvm_vcpu; extern char __kvm_hyp_init[]; extern char __kvm_hyp_init_end[]; -extern char __kvm_hyp_reset[]; extern char __kvm_hyp_vector[]; @@ -59,6 +58,8 @@ extern void __kvm_tlb_flush_local_vmid(struct kvm_vcpu *vcpu); extern int __kvm_vcpu_run(struct kvm_vcpu *vcpu); extern u64 __vgic_v3_get_ich_vtr_el2(void); +extern u64 __vgic_v3_read_vmcr(void); +extern void __vgic_v3_write_vmcr(u32 vmcr); extern void __vgic_v3_init_lrs(void); extern u32 __kvm_get_mdcr_el2(void); diff --git a/arch/arm64/include/asm/kvm_emulate.h b/arch/arm64/include/asm/kvm_emulate.h index f5ea0ba70f07..fe39e6841326 100644 --- a/arch/arm64/include/asm/kvm_emulate.h +++ b/arch/arm64/include/asm/kvm_emulate.h @@ -240,6 +240,12 @@ static inline u8 kvm_vcpu_trap_get_fault_type(const struct kvm_vcpu *vcpu) return kvm_vcpu_get_hsr(vcpu) & ESR_ELx_FSC_TYPE; } +static inline int kvm_vcpu_sys_get_rt(struct kvm_vcpu *vcpu) +{ + u32 esr = kvm_vcpu_get_hsr(vcpu); + return (esr & ESR_ELx_SYS64_ISS_RT_MASK) >> ESR_ELx_SYS64_ISS_RT_SHIFT; +} + static inline unsigned long kvm_vcpu_get_mpidr_aff(struct kvm_vcpu *vcpu) { return vcpu_sys_reg(vcpu, MPIDR_EL1) & MPIDR_HWID_BITMASK; diff --git a/arch/arm64/include/asm/kvm_host.h b/arch/arm64/include/asm/kvm_host.h index e7705e7bb07b..5e19165c5fa8 100644 --- a/arch/arm64/include/asm/kvm_host.h +++ b/arch/arm64/include/asm/kvm_host.h @@ -31,7 +31,6 @@ #define __KVM_HAVE_ARCH_INTC_INITIALIZED #define KVM_USER_MEM_SLOTS 512 -#define KVM_COALESCED_MMIO_PAGE_OFFSET 1 #define KVM_HALT_POLL_NS_DEFAULT 500000 #include <kvm/arm_vgic.h> @@ -42,7 +41,7 @@ #define KVM_VCPU_MAX_FEATURES 4 -#define KVM_REQ_VCPU_EXIT 8 +#define KVM_REQ_VCPU_EXIT (8 | KVM_REQUEST_WAIT | KVM_REQUEST_NO_WAKEUP) int __attribute_const__ kvm_target_cpu(void); int kvm_reset_vcpu(struct kvm_vcpu *vcpu); @@ -362,13 +361,6 @@ static inline void __cpu_init_hyp_mode(phys_addr_t pgd_ptr, __kvm_call_hyp((void *)pgd_ptr, hyp_stack_ptr, vector_ptr); } -void __kvm_hyp_teardown(void); -static inline void __cpu_reset_hyp_mode(unsigned long vector_ptr, - phys_addr_t phys_idmap_start) -{ - kvm_call_hyp(__kvm_hyp_teardown, phys_idmap_start); -} - static inline void kvm_arch_hardware_unsetup(void) {} static inline void kvm_arch_sync_events(struct kvm *kvm) {} static inline void kvm_arch_vcpu_uninit(struct kvm_vcpu *vcpu) {} diff --git a/arch/arm64/include/asm/kvm_mmu.h b/arch/arm64/include/asm/kvm_mmu.h index ed1246014901..a89cc22abadc 100644 --- a/arch/arm64/include/asm/kvm_mmu.h +++ b/arch/arm64/include/asm/kvm_mmu.h @@ -108,7 +108,7 @@ alternative_else_nop_endif #else #include <asm/pgalloc.h> -#include <asm/cachetype.h> +#include <asm/cache.h> #include <asm/cacheflush.h> #include <asm/mmu_context.h> #include <asm/pgtable.h> @@ -155,7 +155,6 @@ void kvm_mmu_free_memory_caches(struct kvm_vcpu *vcpu); phys_addr_t kvm_mmu_get_httbr(void); phys_addr_t kvm_get_idmap_vector(void); -phys_addr_t kvm_get_idmap_start(void); int kvm_mmu_init(void); void kvm_clear_hyp_idmap(void); @@ -242,12 +241,13 @@ static inline void __coherent_cache_guest_page(struct kvm_vcpu *vcpu, kvm_flush_dcache_to_poc(va, size); - if (!icache_is_aliasing()) { /* PIPT */ - flush_icache_range((unsigned long)va, - (unsigned long)va + size); - } else if (!icache_is_aivivt()) { /* non ASID-tagged VIVT */ + if (icache_is_aliasing()) { /* any kind of VIPT cache */ __flush_icache_all(); + } else if (is_kernel_in_hyp_mode() || !icache_is_vpipt()) { + /* PIPT or VPIPT at EL2 (see comment in __kvm_tlb_flush_vmid_ipa) */ + flush_icache_range((unsigned long)va, + (unsigned long)va + size); } } @@ -307,7 +307,7 @@ static inline void __kvm_extend_hypmap(pgd_t *boot_hyp_pgd, static inline unsigned int kvm_get_vmid_bits(void) { - int reg = read_system_reg(SYS_ID_AA64MMFR1_EL1); + int reg = read_sanitised_ftr_reg(SYS_ID_AA64MMFR1_EL1); return (cpuid_feature_extract_unsigned_field(reg, ID_AA64MMFR1_VMIDBITS_SHIFT) == 2) ? 16 : 8; } diff --git a/arch/arm64/include/asm/mmu.h b/arch/arm64/include/asm/mmu.h index 47619411f0ff..5468c834b072 100644 --- a/arch/arm64/include/asm/mmu.h +++ b/arch/arm64/include/asm/mmu.h @@ -37,5 +37,6 @@ extern void create_pgd_mapping(struct mm_struct *mm, phys_addr_t phys, unsigned long virt, phys_addr_t size, pgprot_t prot, bool page_mappings_only); extern void *fixmap_remap_fdt(phys_addr_t dt_phys); +extern void mark_linear_text_alias_ro(void); #endif diff --git a/arch/arm64/include/asm/module.h b/arch/arm64/include/asm/module.h index 06ff7fd9e81f..d57693f5d4ec 100644 --- a/arch/arm64/include/asm/module.h +++ b/arch/arm64/include/asm/module.h @@ -17,26 +17,26 @@ #define __ASM_MODULE_H #include <asm-generic/module.h> -#include <asm/memory.h> #define MODULE_ARCH_VERMAGIC "aarch64" #ifdef CONFIG_ARM64_MODULE_PLTS -struct mod_arch_specific { +struct mod_plt_sec { struct elf64_shdr *plt; int plt_num_entries; int plt_max_entries; }; + +struct mod_arch_specific { + struct mod_plt_sec core; + struct mod_plt_sec init; +}; #endif -u64 module_emit_plt_entry(struct module *mod, const Elf64_Rela *rela, +u64 module_emit_plt_entry(struct module *mod, void *loc, const Elf64_Rela *rela, Elf64_Sym *sym); #ifdef CONFIG_RANDOMIZE_BASE -#ifdef CONFIG_MODVERSIONS -#define ARCH_RELOCATES_KCRCTAB -#define reloc_start (kimage_vaddr - KIMAGE_VADDR) -#endif extern u64 module_alloc_base; #else #define module_alloc_base ((u64)_etext - MODULES_VSIZE) diff --git a/arch/arm64/include/asm/pci.h b/arch/arm64/include/asm/pci.h index b9a7ba9ca44c..1fc19744ffe9 100644 --- a/arch/arm64/include/asm/pci.h +++ b/arch/arm64/include/asm/pci.h @@ -22,6 +22,8 @@ */ #define PCI_DMA_BUS_IS_PHYS (0) +#define ARCH_GENERIC_PCI_MMAP_RESOURCE 1 + extern int isa_dma_bridge_buggy; #ifdef CONFIG_PCI diff --git a/arch/arm64/include/asm/pgtable.h b/arch/arm64/include/asm/pgtable.h index 0eef6064bf3b..c213fdbd056c 100644 --- a/arch/arm64/include/asm/pgtable.h +++ b/arch/arm64/include/asm/pgtable.h @@ -74,6 +74,16 @@ extern unsigned long empty_zero_page[PAGE_SIZE / sizeof(unsigned long)]; #define pte_user_exec(pte) (!(pte_val(pte) & PTE_UXN)) #define pte_cont(pte) (!!(pte_val(pte) & PTE_CONT)) +#define pte_cont_addr_end(addr, end) \ +({ unsigned long __boundary = ((addr) + CONT_PTE_SIZE) & CONT_PTE_MASK; \ + (__boundary - 1 < (end) - 1) ? __boundary : (end); \ +}) + +#define pmd_cont_addr_end(addr, end) \ +({ unsigned long __boundary = ((addr) + CONT_PMD_SIZE) & CONT_PMD_MASK; \ + (__boundary - 1 < (end) - 1) ? __boundary : (end); \ +}) + #ifdef CONFIG_ARM64_HW_AFDBM #define pte_hw_dirty(pte) (pte_write(pte) && !(pte_val(pte) & PTE_RDONLY)) #else diff --git a/arch/arm64/include/asm/processor.h b/arch/arm64/include/asm/processor.h index c97b8bd2acba..9428b93fefb2 100644 --- a/arch/arm64/include/asm/processor.h +++ b/arch/arm64/include/asm/processor.h @@ -50,6 +50,7 @@ extern phys_addr_t arm64_dma_phys_limit; #define ARCH_LOW_ADDRESS_LIMIT (arm64_dma_phys_limit - 1) struct debug_info { +#ifdef CONFIG_HAVE_HW_BREAKPOINT /* Have we suspended stepping by a debugger? */ int suspended_step; /* Allow breakpoints and watchpoints to be disabled for this thread. */ @@ -58,6 +59,7 @@ struct debug_info { /* Hardware breakpoints pinned to this task. */ struct perf_event *hbp_break[ARM_MAX_BRP]; struct perf_event *hbp_watch[ARM_MAX_WRP]; +#endif }; struct cpu_context { diff --git a/arch/arm64/include/asm/sections.h b/arch/arm64/include/asm/sections.h index 4e7e7067afdb..941267caa39c 100644 --- a/arch/arm64/include/asm/sections.h +++ b/arch/arm64/include/asm/sections.h @@ -24,6 +24,8 @@ extern char __hibernate_exit_text_start[], __hibernate_exit_text_end[]; extern char __hyp_idmap_text_start[], __hyp_idmap_text_end[]; extern char __hyp_text_start[], __hyp_text_end[]; extern char __idmap_text_start[], __idmap_text_end[]; +extern char __initdata_begin[], __initdata_end[]; +extern char __inittext_begin[], __inittext_end[]; extern char __irqentry_text_start[], __irqentry_text_end[]; extern char __mmuoff_data_start[], __mmuoff_data_end[]; diff --git a/arch/arm64/include/asm/smp.h b/arch/arm64/include/asm/smp.h index d050d720a1b4..55f08c5acfad 100644 --- a/arch/arm64/include/asm/smp.h +++ b/arch/arm64/include/asm/smp.h @@ -148,6 +148,9 @@ static inline void cpu_panic_kernel(void) */ bool cpus_are_stuck_in_kernel(void); +extern void smp_send_crash_stop(void); +extern bool smp_crash_stop_failed(void); + #endif /* ifndef __ASSEMBLY__ */ #endif /* ifndef __ASM_SMP_H */ diff --git a/arch/arm64/include/asm/sysreg.h b/arch/arm64/include/asm/sysreg.h index ac24b6e798b1..15c142ce991c 100644 --- a/arch/arm64/include/asm/sysreg.h +++ b/arch/arm64/include/asm/sysreg.h @@ -48,6 +48,8 @@ ((crn) << CRn_shift) | ((crm) << CRm_shift) | \ ((op2) << Op2_shift)) +#define sys_insn sys_reg + #define sys_reg_Op0(id) (((id) >> Op0_shift) & Op0_mask) #define sys_reg_Op1(id) (((id) >> Op1_shift) & Op1_mask) #define sys_reg_CRn(id) (((id) >> CRn_shift) & CRn_mask) @@ -81,6 +83,41 @@ #endif /* CONFIG_BROKEN_GAS_INST */ +#define REG_PSTATE_PAN_IMM sys_reg(0, 0, 4, 0, 4) +#define REG_PSTATE_UAO_IMM sys_reg(0, 0, 4, 0, 3) + +#define SET_PSTATE_PAN(x) __emit_inst(0xd5000000 | REG_PSTATE_PAN_IMM | \ + (!!x)<<8 | 0x1f) +#define SET_PSTATE_UAO(x) __emit_inst(0xd5000000 | REG_PSTATE_UAO_IMM | \ + (!!x)<<8 | 0x1f) + +#define SYS_DC_ISW sys_insn(1, 0, 7, 6, 2) +#define SYS_DC_CSW sys_insn(1, 0, 7, 10, 2) +#define SYS_DC_CISW sys_insn(1, 0, 7, 14, 2) + +#define SYS_OSDTRRX_EL1 sys_reg(2, 0, 0, 0, 2) +#define SYS_MDCCINT_EL1 sys_reg(2, 0, 0, 2, 0) +#define SYS_MDSCR_EL1 sys_reg(2, 0, 0, 2, 2) +#define SYS_OSDTRTX_EL1 sys_reg(2, 0, 0, 3, 2) +#define SYS_OSECCR_EL1 sys_reg(2, 0, 0, 6, 2) +#define SYS_DBGBVRn_EL1(n) sys_reg(2, 0, 0, n, 4) +#define SYS_DBGBCRn_EL1(n) sys_reg(2, 0, 0, n, 5) +#define SYS_DBGWVRn_EL1(n) sys_reg(2, 0, 0, n, 6) +#define SYS_DBGWCRn_EL1(n) sys_reg(2, 0, 0, n, 7) +#define SYS_MDRAR_EL1 sys_reg(2, 0, 1, 0, 0) +#define SYS_OSLAR_EL1 sys_reg(2, 0, 1, 0, 4) +#define SYS_OSLSR_EL1 sys_reg(2, 0, 1, 1, 4) +#define SYS_OSDLR_EL1 sys_reg(2, 0, 1, 3, 4) +#define SYS_DBGPRCR_EL1 sys_reg(2, 0, 1, 4, 4) +#define SYS_DBGCLAIMSET_EL1 sys_reg(2, 0, 7, 8, 6) +#define SYS_DBGCLAIMCLR_EL1 sys_reg(2, 0, 7, 9, 6) +#define SYS_DBGAUTHSTATUS_EL1 sys_reg(2, 0, 7, 14, 6) +#define SYS_MDCCSR_EL0 sys_reg(2, 3, 0, 1, 0) +#define SYS_DBGDTR_EL0 sys_reg(2, 3, 0, 4, 0) +#define SYS_DBGDTRRX_EL0 sys_reg(2, 3, 0, 5, 0) +#define SYS_DBGDTRTX_EL0 sys_reg(2, 3, 0, 5, 0) +#define SYS_DBGVCR32_EL2 sys_reg(2, 4, 0, 7, 0) + #define SYS_MIDR_EL1 sys_reg(3, 0, 0, 0, 0) #define SYS_MPIDR_EL1 sys_reg(3, 0, 0, 0, 5) #define SYS_REVIDR_EL1 sys_reg(3, 0, 0, 0, 6) @@ -88,6 +125,7 @@ #define SYS_ID_PFR0_EL1 sys_reg(3, 0, 0, 1, 0) #define SYS_ID_PFR1_EL1 sys_reg(3, 0, 0, 1, 1) #define SYS_ID_DFR0_EL1 sys_reg(3, 0, 0, 1, 2) +#define SYS_ID_AFR0_EL1 sys_reg(3, 0, 0, 1, 3) #define SYS_ID_MMFR0_EL1 sys_reg(3, 0, 0, 1, 4) #define SYS_ID_MMFR1_EL1 sys_reg(3, 0, 0, 1, 5) #define SYS_ID_MMFR2_EL1 sys_reg(3, 0, 0, 1, 6) @@ -118,17 +156,127 @@ #define SYS_ID_AA64MMFR1_EL1 sys_reg(3, 0, 0, 7, 1) #define SYS_ID_AA64MMFR2_EL1 sys_reg(3, 0, 0, 7, 2) -#define SYS_CNTFRQ_EL0 sys_reg(3, 3, 14, 0, 0) +#define SYS_SCTLR_EL1 sys_reg(3, 0, 1, 0, 0) +#define SYS_ACTLR_EL1 sys_reg(3, 0, 1, 0, 1) +#define SYS_CPACR_EL1 sys_reg(3, 0, 1, 0, 2) + +#define SYS_TTBR0_EL1 sys_reg(3, 0, 2, 0, 0) +#define SYS_TTBR1_EL1 sys_reg(3, 0, 2, 0, 1) +#define SYS_TCR_EL1 sys_reg(3, 0, 2, 0, 2) + +#define SYS_ICC_PMR_EL1 sys_reg(3, 0, 4, 6, 0) + +#define SYS_AFSR0_EL1 sys_reg(3, 0, 5, 1, 0) +#define SYS_AFSR1_EL1 sys_reg(3, 0, 5, 1, 1) +#define SYS_ESR_EL1 sys_reg(3, 0, 5, 2, 0) +#define SYS_FAR_EL1 sys_reg(3, 0, 6, 0, 0) +#define SYS_PAR_EL1 sys_reg(3, 0, 7, 4, 0) + +#define SYS_PMINTENSET_EL1 sys_reg(3, 0, 9, 14, 1) +#define SYS_PMINTENCLR_EL1 sys_reg(3, 0, 9, 14, 2) + +#define SYS_MAIR_EL1 sys_reg(3, 0, 10, 2, 0) +#define SYS_AMAIR_EL1 sys_reg(3, 0, 10, 3, 0) + +#define SYS_VBAR_EL1 sys_reg(3, 0, 12, 0, 0) + +#define SYS_ICC_DIR_EL1 sys_reg(3, 0, 12, 11, 1) +#define SYS_ICC_SGI1R_EL1 sys_reg(3, 0, 12, 11, 5) +#define SYS_ICC_IAR1_EL1 sys_reg(3, 0, 12, 12, 0) +#define SYS_ICC_EOIR1_EL1 sys_reg(3, 0, 12, 12, 1) +#define SYS_ICC_BPR1_EL1 sys_reg(3, 0, 12, 12, 3) +#define SYS_ICC_CTLR_EL1 sys_reg(3, 0, 12, 12, 4) +#define SYS_ICC_SRE_EL1 sys_reg(3, 0, 12, 12, 5) +#define SYS_ICC_GRPEN1_EL1 sys_reg(3, 0, 12, 12, 7) + +#define SYS_CONTEXTIDR_EL1 sys_reg(3, 0, 13, 0, 1) +#define SYS_TPIDR_EL1 sys_reg(3, 0, 13, 0, 4) + +#define SYS_CNTKCTL_EL1 sys_reg(3, 0, 14, 1, 0) + +#define SYS_CLIDR_EL1 sys_reg(3, 1, 0, 0, 1) +#define SYS_AIDR_EL1 sys_reg(3, 1, 0, 0, 7) + +#define SYS_CSSELR_EL1 sys_reg(3, 2, 0, 0, 0) + #define SYS_CTR_EL0 sys_reg(3, 3, 0, 0, 1) #define SYS_DCZID_EL0 sys_reg(3, 3, 0, 0, 7) -#define REG_PSTATE_PAN_IMM sys_reg(0, 0, 4, 0, 4) -#define REG_PSTATE_UAO_IMM sys_reg(0, 0, 4, 0, 3) +#define SYS_PMCR_EL0 sys_reg(3, 3, 9, 12, 0) +#define SYS_PMCNTENSET_EL0 sys_reg(3, 3, 9, 12, 1) +#define SYS_PMCNTENCLR_EL0 sys_reg(3, 3, 9, 12, 2) +#define SYS_PMOVSCLR_EL0 sys_reg(3, 3, 9, 12, 3) +#define SYS_PMSWINC_EL0 sys_reg(3, 3, 9, 12, 4) +#define SYS_PMSELR_EL0 sys_reg(3, 3, 9, 12, 5) +#define SYS_PMCEID0_EL0 sys_reg(3, 3, 9, 12, 6) +#define SYS_PMCEID1_EL0 sys_reg(3, 3, 9, 12, 7) +#define SYS_PMCCNTR_EL0 sys_reg(3, 3, 9, 13, 0) +#define SYS_PMXEVTYPER_EL0 sys_reg(3, 3, 9, 13, 1) +#define SYS_PMXEVCNTR_EL0 sys_reg(3, 3, 9, 13, 2) +#define SYS_PMUSERENR_EL0 sys_reg(3, 3, 9, 14, 0) +#define SYS_PMOVSSET_EL0 sys_reg(3, 3, 9, 14, 3) + +#define SYS_TPIDR_EL0 sys_reg(3, 3, 13, 0, 2) +#define SYS_TPIDRRO_EL0 sys_reg(3, 3, 13, 0, 3) -#define SET_PSTATE_PAN(x) __emit_inst(0xd5000000 | REG_PSTATE_PAN_IMM | \ - (!!x)<<8 | 0x1f) -#define SET_PSTATE_UAO(x) __emit_inst(0xd5000000 | REG_PSTATE_UAO_IMM | \ - (!!x)<<8 | 0x1f) +#define SYS_CNTFRQ_EL0 sys_reg(3, 3, 14, 0, 0) + +#define SYS_CNTP_TVAL_EL0 sys_reg(3, 3, 14, 2, 0) +#define SYS_CNTP_CTL_EL0 sys_reg(3, 3, 14, 2, 1) +#define SYS_CNTP_CVAL_EL0 sys_reg(3, 3, 14, 2, 2) + +#define __PMEV_op2(n) ((n) & 0x7) +#define __CNTR_CRm(n) (0x8 | (((n) >> 3) & 0x3)) +#define SYS_PMEVCNTRn_EL0(n) sys_reg(3, 3, 14, __CNTR_CRm(n), __PMEV_op2(n)) +#define __TYPER_CRm(n) (0xc | (((n) >> 3) & 0x3)) +#define SYS_PMEVTYPERn_EL0(n) sys_reg(3, 3, 14, __TYPER_CRm(n), __PMEV_op2(n)) + +#define SYS_PMCCFILTR_EL0 sys_reg (3, 3, 14, 15, 7) + +#define SYS_DACR32_EL2 sys_reg(3, 4, 3, 0, 0) +#define SYS_IFSR32_EL2 sys_reg(3, 4, 5, 0, 1) +#define SYS_FPEXC32_EL2 sys_reg(3, 4, 5, 3, 0) + +#define __SYS__AP0Rx_EL2(x) sys_reg(3, 4, 12, 8, x) +#define SYS_ICH_AP0R0_EL2 __SYS__AP0Rx_EL2(0) +#define SYS_ICH_AP0R1_EL2 __SYS__AP0Rx_EL2(1) +#define SYS_ICH_AP0R2_EL2 __SYS__AP0Rx_EL2(2) +#define SYS_ICH_AP0R3_EL2 __SYS__AP0Rx_EL2(3) + +#define __SYS__AP1Rx_EL2(x) sys_reg(3, 4, 12, 9, x) +#define SYS_ICH_AP1R0_EL2 __SYS__AP1Rx_EL2(0) +#define SYS_ICH_AP1R1_EL2 __SYS__AP1Rx_EL2(1) +#define SYS_ICH_AP1R2_EL2 __SYS__AP1Rx_EL2(2) +#define SYS_ICH_AP1R3_EL2 __SYS__AP1Rx_EL2(3) + +#define SYS_ICH_VSEIR_EL2 sys_reg(3, 4, 12, 9, 4) +#define SYS_ICC_SRE_EL2 sys_reg(3, 4, 12, 9, 5) +#define SYS_ICH_HCR_EL2 sys_reg(3, 4, 12, 11, 0) +#define SYS_ICH_VTR_EL2 sys_reg(3, 4, 12, 11, 1) +#define SYS_ICH_MISR_EL2 sys_reg(3, 4, 12, 11, 2) +#define SYS_ICH_EISR_EL2 sys_reg(3, 4, 12, 11, 3) +#define SYS_ICH_ELSR_EL2 sys_reg(3, 4, 12, 11, 5) +#define SYS_ICH_VMCR_EL2 sys_reg(3, 4, 12, 11, 7) + +#define __SYS__LR0_EL2(x) sys_reg(3, 4, 12, 12, x) +#define SYS_ICH_LR0_EL2 __SYS__LR0_EL2(0) +#define SYS_ICH_LR1_EL2 __SYS__LR0_EL2(1) +#define SYS_ICH_LR2_EL2 __SYS__LR0_EL2(2) +#define SYS_ICH_LR3_EL2 __SYS__LR0_EL2(3) +#define SYS_ICH_LR4_EL2 __SYS__LR0_EL2(4) +#define SYS_ICH_LR5_EL2 __SYS__LR0_EL2(5) +#define SYS_ICH_LR6_EL2 __SYS__LR0_EL2(6) +#define SYS_ICH_LR7_EL2 __SYS__LR0_EL2(7) + +#define __SYS__LR8_EL2(x) sys_reg(3, 4, 12, 13, x) +#define SYS_ICH_LR8_EL2 __SYS__LR8_EL2(0) +#define SYS_ICH_LR9_EL2 __SYS__LR8_EL2(1) +#define SYS_ICH_LR10_EL2 __SYS__LR8_EL2(2) +#define SYS_ICH_LR11_EL2 __SYS__LR8_EL2(3) +#define SYS_ICH_LR12_EL2 __SYS__LR8_EL2(4) +#define SYS_ICH_LR13_EL2 __SYS__LR8_EL2(5) +#define SYS_ICH_LR14_EL2 __SYS__LR8_EL2(6) +#define SYS_ICH_LR15_EL2 __SYS__LR8_EL2(7) /* Common SCTLR_ELx flags. */ #define SCTLR_ELx_EE (1 << 25) @@ -156,6 +304,11 @@ #define ID_AA64ISAR0_SHA1_SHIFT 8 #define ID_AA64ISAR0_AES_SHIFT 4 +/* id_aa64isar1 */ +#define ID_AA64ISAR1_LRCPC_SHIFT 20 +#define ID_AA64ISAR1_FCMA_SHIFT 16 +#define ID_AA64ISAR1_JSCVT_SHIFT 12 + /* id_aa64pfr0 */ #define ID_AA64PFR0_GIC_SHIFT 24 #define ID_AA64PFR0_ASIMD_SHIFT 20 diff --git a/arch/arm64/include/asm/uaccess.h b/arch/arm64/include/asm/uaccess.h index ba497172610d..7b8a04789cef 100644 --- a/arch/arm64/include/asm/uaccess.h +++ b/arch/arm64/include/asm/uaccess.h @@ -69,20 +69,21 @@ static inline void set_fs(mm_segment_t fs) */ #define __range_ok(addr, size) \ ({ \ + unsigned long __addr = (unsigned long __force)(addr); \ unsigned long flag, roksum; \ __chk_user_ptr(addr); \ asm("adds %1, %1, %3; ccmp %1, %4, #2, cc; cset %0, ls" \ : "=&r" (flag), "=&r" (roksum) \ - : "1" (addr), "Ir" (size), \ + : "1" (__addr), "Ir" (size), \ "r" (current_thread_info()->addr_limit) \ : "cc"); \ flag; \ }) /* - * When dealing with data aborts or instruction traps we may end up with - * a tagged userland pointer. Clear the tag to get a sane pointer to pass - * on to access_ok(), for instance. + * When dealing with data aborts, watchpoints, or instruction traps we may end + * up with a tagged userland pointer. Clear the tag to get a sane pointer to + * pass on to access_ok(), for instance. */ #define untagged_addr(addr) sign_extend64(addr, 55) @@ -230,7 +231,7 @@ do { \ (err), ARM64_HAS_UAO); \ break; \ case 8: \ - __get_user_asm("ldr", "ldtr", "%", __gu_val, (ptr), \ + __get_user_asm("ldr", "ldtr", "%x", __gu_val, (ptr), \ (err), ARM64_HAS_UAO); \ break; \ default: \ @@ -297,7 +298,7 @@ do { \ (err), ARM64_HAS_UAO); \ break; \ case 8: \ - __put_user_asm("str", "sttr", "%", __pu_val, (ptr), \ + __put_user_asm("str", "sttr", "%x", __pu_val, (ptr), \ (err), ARM64_HAS_UAO); \ break; \ default: \ diff --git a/arch/arm64/include/asm/unistd.h b/arch/arm64/include/asm/unistd.h index bdbeb06dc11e..a0baa9af5487 100644 --- a/arch/arm64/include/asm/unistd.h +++ b/arch/arm64/include/asm/unistd.h @@ -14,7 +14,6 @@ * along with this program. If not, see <http://www.gnu.org/licenses/>. */ #ifdef CONFIG_COMPAT -#define __ARCH_WANT_COMPAT_SYS_GETDENTS64 #define __ARCH_WANT_COMPAT_STAT64 #define __ARCH_WANT_SYS_GETHOSTNAME #define __ARCH_WANT_SYS_PAUSE diff --git a/arch/arm64/include/asm/unistd32.h b/arch/arm64/include/asm/unistd32.h index c66b51aab195..ef292160748c 100644 --- a/arch/arm64/include/asm/unistd32.h +++ b/arch/arm64/include/asm/unistd32.h @@ -456,7 +456,7 @@ __SYSCALL(__NR_setfsuid32, sys_setfsuid) #define __NR_setfsgid32 216 __SYSCALL(__NR_setfsgid32, sys_setfsgid) #define __NR_getdents64 217 -__SYSCALL(__NR_getdents64, compat_sys_getdents64) +__SYSCALL(__NR_getdents64, sys_getdents64) #define __NR_pivot_root 218 __SYSCALL(__NR_pivot_root, sys_pivot_root) #define __NR_mincore 219 diff --git a/arch/arm64/include/asm/virt.h b/arch/arm64/include/asm/virt.h index 439f6b5d31f6..c5f89442785c 100644 --- a/arch/arm64/include/asm/virt.h +++ b/arch/arm64/include/asm/virt.h @@ -19,25 +19,38 @@ #define __ASM__VIRT_H /* - * The arm64 hcall implementation uses x0 to specify the hcall type. A value - * less than 0xfff indicates a special hcall, such as get/set vector. - * Any other value is used as a pointer to the function to call. + * The arm64 hcall implementation uses x0 to specify the hcall + * number. A value less than HVC_STUB_HCALL_NR indicates a special + * hcall, such as set vector. Any other value is handled in a + * hypervisor specific way. + * + * The hypercall is allowed to clobber any of the caller-saved + * registers (x0-x18), so it is advisable to use it through the + * indirection of a function call (as implemented in hyp-stub.S). */ -/* HVC_GET_VECTORS - Return the value of the vbar_el2 register. */ -#define HVC_GET_VECTORS 0 - /* * HVC_SET_VECTORS - Set the value of the vbar_el2 register. * * @x1: Physical address of the new vector table. */ -#define HVC_SET_VECTORS 1 +#define HVC_SET_VECTORS 0 /* * HVC_SOFT_RESTART - CPU soft reset, used by the cpu_soft_restart routine. */ -#define HVC_SOFT_RESTART 2 +#define HVC_SOFT_RESTART 1 + +/* + * HVC_RESET_VECTORS - Restore the vectors to the original HYP stubs + */ +#define HVC_RESET_VECTORS 2 + +/* Max number of HYP stub hypercalls */ +#define HVC_STUB_HCALL_NR 3 + +/* Error returned when an invalid stub number is passed into x0 */ +#define HVC_STUB_ERR 0xbadca11 #define BOOT_CPU_MODE_EL1 (0xe11) #define BOOT_CPU_MODE_EL2 (0xe12) @@ -61,7 +74,7 @@ extern u32 __boot_cpu_mode[2]; void __hyp_set_vectors(phys_addr_t phys_vector_base); -phys_addr_t __hyp_get_vectors(void); +void __hyp_reset_vectors(void); /* Reports the availability of HYP mode */ static inline bool is_hyp_mode_available(void) diff --git a/arch/arm64/include/uapi/asm/Kbuild b/arch/arm64/include/uapi/asm/Kbuild index 825b0fe51c2b..13a97aa2285f 100644 --- a/arch/arm64/include/uapi/asm/Kbuild +++ b/arch/arm64/include/uapi/asm/Kbuild @@ -2,21 +2,3 @@ include include/uapi/asm-generic/Kbuild.asm generic-y += kvm_para.h - -header-y += auxvec.h -header-y += bitsperlong.h -header-y += byteorder.h -header-y += fcntl.h -header-y += hwcap.h -header-y += kvm_para.h -header-y += perf_regs.h -header-y += param.h -header-y += ptrace.h -header-y += setup.h -header-y += sigcontext.h -header-y += siginfo.h -header-y += signal.h -header-y += stat.h -header-y += statfs.h -header-y += ucontext.h -header-y += unistd.h diff --git a/arch/arm64/include/uapi/asm/hwcap.h b/arch/arm64/include/uapi/asm/hwcap.h index 61c263cba272..4e187ce2a811 100644 --- a/arch/arm64/include/uapi/asm/hwcap.h +++ b/arch/arm64/include/uapi/asm/hwcap.h @@ -32,5 +32,8 @@ #define HWCAP_ASIMDHP (1 << 10) #define HWCAP_CPUID (1 << 11) #define HWCAP_ASIMDRDM (1 << 12) +#define HWCAP_JSCVT (1 << 13) +#define HWCAP_FCMA (1 << 14) +#define HWCAP_LRCPC (1 << 15) #endif /* _UAPI__ASM_HWCAP_H */ diff --git a/arch/arm64/include/uapi/asm/kvm.h b/arch/arm64/include/uapi/asm/kvm.h index c2860358ae3e..70eea2ecc663 100644 --- a/arch/arm64/include/uapi/asm/kvm.h +++ b/arch/arm64/include/uapi/asm/kvm.h @@ -39,6 +39,8 @@ #define __KVM_HAVE_IRQ_LINE #define __KVM_HAVE_READONLY_MEM +#define KVM_COALESCED_MMIO_PAGE_OFFSET 1 + #define KVM_REG_SIZE(id) \ (1U << (((id) & KVM_REG_SIZE_MASK) >> KVM_REG_SIZE_SHIFT)) @@ -143,6 +145,8 @@ struct kvm_debug_exit_arch { #define KVM_GUESTDBG_USE_HW (1 << 17) struct kvm_sync_regs { + /* Used with KVM_CAP_ARM_USER_IRQ */ + __u64 device_irq_level; }; struct kvm_arch_memory_slot { @@ -212,13 +216,17 @@ struct kvm_arch_memory_slot { #define KVM_DEV_ARM_VGIC_GRP_REDIST_REGS 5 #define KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS 6 #define KVM_DEV_ARM_VGIC_GRP_LEVEL_INFO 7 +#define KVM_DEV_ARM_VGIC_GRP_ITS_REGS 8 #define KVM_DEV_ARM_VGIC_LINE_LEVEL_INFO_SHIFT 10 #define KVM_DEV_ARM_VGIC_LINE_LEVEL_INFO_MASK \ (0x3fffffULL << KVM_DEV_ARM_VGIC_LINE_LEVEL_INFO_SHIFT) #define KVM_DEV_ARM_VGIC_LINE_LEVEL_INTID_MASK 0x3ff #define VGIC_LEVEL_INFO_LINE_LEVEL 0 -#define KVM_DEV_ARM_VGIC_CTRL_INIT 0 +#define KVM_DEV_ARM_VGIC_CTRL_INIT 0 +#define KVM_DEV_ARM_ITS_SAVE_TABLES 1 +#define KVM_DEV_ARM_ITS_RESTORE_TABLES 2 +#define KVM_DEV_ARM_VGIC_SAVE_PENDING_TABLES 3 /* Device Control API on vcpu fd */ #define KVM_ARM_VCPU_PMU_V3_CTRL 0 diff --git a/arch/arm64/kernel/Makefile b/arch/arm64/kernel/Makefile index 1606c6b2a280..1dcb69d3d0e5 100644 --- a/arch/arm64/kernel/Makefile +++ b/arch/arm64/kernel/Makefile @@ -50,6 +50,9 @@ arm64-obj-$(CONFIG_RANDOMIZE_BASE) += kaslr.o arm64-obj-$(CONFIG_HIBERNATION) += hibernate.o hibernate-asm.o arm64-obj-$(CONFIG_KEXEC) += machine_kexec.o relocate_kernel.o \ cpu-reset.o +arm64-obj-$(CONFIG_ARM64_RELOC_TEST) += arm64-reloc-test.o +arm64-reloc-test-y := reloc_test_core.o reloc_test_syms.o +arm64-obj-$(CONFIG_CRASH_DUMP) += crash_dump.o obj-y += $(arm64-obj-y) vdso/ probes/ obj-m += $(arm64-obj-m) diff --git a/arch/arm64/kernel/alternative.c b/arch/arm64/kernel/alternative.c index 06d650f61da7..8840c109c5d6 100644 --- a/arch/arm64/kernel/alternative.c +++ b/arch/arm64/kernel/alternative.c @@ -105,11 +105,11 @@ static u32 get_alt_insn(struct alt_instr *alt, u32 *insnptr, u32 *altinsnptr) return insn; } -static void __apply_alternatives(void *alt_region) +static void __apply_alternatives(void *alt_region, bool use_linear_alias) { struct alt_instr *alt; struct alt_region *region = alt_region; - u32 *origptr, *replptr; + u32 *origptr, *replptr, *updptr; for (alt = region->begin; alt < region->end; alt++) { u32 insn; @@ -124,11 +124,12 @@ static void __apply_alternatives(void *alt_region) origptr = ALT_ORIG_PTR(alt); replptr = ALT_REPL_PTR(alt); + updptr = use_linear_alias ? (u32 *)lm_alias(origptr) : origptr; nr_inst = alt->alt_len / sizeof(insn); for (i = 0; i < nr_inst; i++) { insn = get_alt_insn(alt, origptr + i, replptr + i); - *(origptr + i) = cpu_to_le32(insn); + updptr[i] = cpu_to_le32(insn); } flush_icache_range((uintptr_t)origptr, @@ -155,7 +156,7 @@ static int __apply_alternatives_multi_stop(void *unused) isb(); } else { BUG_ON(patched); - __apply_alternatives(®ion); + __apply_alternatives(®ion, true); /* Barriers provided by the cache flushing */ WRITE_ONCE(patched, 1); } @@ -176,5 +177,5 @@ void apply_alternatives(void *start, size_t length) .end = start + length, }; - __apply_alternatives(®ion); + __apply_alternatives(®ion, false); } diff --git a/arch/arm64/kernel/armv8_deprecated.c b/arch/arm64/kernel/armv8_deprecated.c index 657977e77ec8..f0e6d717885b 100644 --- a/arch/arm64/kernel/armv8_deprecated.c +++ b/arch/arm64/kernel/armv8_deprecated.c @@ -306,7 +306,8 @@ do { \ _ASM_EXTABLE(0b, 4b) \ _ASM_EXTABLE(1b, 4b) \ : "=&r" (res), "+r" (data), "=&r" (temp), "=&r" (temp2) \ - : "r" (addr), "i" (-EAGAIN), "i" (-EFAULT), \ + : "r" ((unsigned long)addr), "i" (-EAGAIN), \ + "i" (-EFAULT), \ "i" (__SWP_LL_SC_LOOPS) \ : "memory"); \ uaccess_disable(); \ diff --git a/arch/arm64/kernel/cacheinfo.c b/arch/arm64/kernel/cacheinfo.c index 3f2250fc391b..380f2e2fbed5 100644 --- a/arch/arm64/kernel/cacheinfo.c +++ b/arch/arm64/kernel/cacheinfo.c @@ -17,15 +17,9 @@ * along with this program. If not, see <http://www.gnu.org/licenses/>. */ -#include <linux/bitops.h> #include <linux/cacheinfo.h> -#include <linux/cpu.h> -#include <linux/compiler.h> #include <linux/of.h> -#include <asm/cachetype.h> -#include <asm/processor.h> - #define MAX_CACHE_LEVEL 7 /* Max 7 level supported */ /* Ctypen, bits[3(n - 1) + 2 : 3(n - 1)], for n = 1 to 7 */ #define CLIDR_CTYPE_SHIFT(level) (3 * (level - 1)) @@ -43,43 +37,11 @@ static inline enum cache_type get_cache_type(int level) return CLIDR_CTYPE(clidr, level); } -/* - * Cache Size Selection Register(CSSELR) selects which Cache Size ID - * Register(CCSIDR) is accessible by specifying the required cache - * level and the cache type. We need to ensure that no one else changes - * CSSELR by calling this in non-preemtible context - */ -u64 __attribute_const__ cache_get_ccsidr(u64 csselr) -{ - u64 ccsidr; - - WARN_ON(preemptible()); - - write_sysreg(csselr, csselr_el1); - isb(); - ccsidr = read_sysreg(ccsidr_el1); - - return ccsidr; -} - static void ci_leaf_init(struct cacheinfo *this_leaf, enum cache_type type, unsigned int level) { - bool is_icache = type & CACHE_TYPE_INST; - u64 tmp = cache_get_ccsidr((level - 1) << 1 | is_icache); - this_leaf->level = level; this_leaf->type = type; - this_leaf->coherency_line_size = CACHE_LINESIZE(tmp); - this_leaf->number_of_sets = CACHE_NUMSETS(tmp); - this_leaf->ways_of_associativity = CACHE_ASSOCIATIVITY(tmp); - this_leaf->size = this_leaf->number_of_sets * - this_leaf->coherency_line_size * this_leaf->ways_of_associativity; - this_leaf->attributes = - ((tmp & CCSIDR_EL1_WRITE_THROUGH) ? CACHE_WRITE_THROUGH : 0) | - ((tmp & CCSIDR_EL1_WRITE_BACK) ? CACHE_WRITE_BACK : 0) | - ((tmp & CCSIDR_EL1_READ_ALLOCATE) ? CACHE_READ_ALLOCATE : 0) | - ((tmp & CCSIDR_EL1_WRITE_ALLOCATE) ? CACHE_WRITE_ALLOCATE : 0); } static int __init_cache_level(unsigned int cpu) diff --git a/arch/arm64/kernel/cpufeature.c b/arch/arm64/kernel/cpufeature.c index 6eb77ae99b79..94b8f7fc3310 100644 --- a/arch/arm64/kernel/cpufeature.c +++ b/arch/arm64/kernel/cpufeature.c @@ -97,6 +97,13 @@ static const struct arm64_ftr_bits ftr_id_aa64isar0[] = { ARM64_FTR_END, }; +static const struct arm64_ftr_bits ftr_id_aa64isar1[] = { + ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_EXACT, ID_AA64ISAR1_LRCPC_SHIFT, 4, 0), + ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_EXACT, ID_AA64ISAR1_FCMA_SHIFT, 4, 0), + ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_EXACT, ID_AA64ISAR1_JSCVT_SHIFT, 4, 0), + ARM64_FTR_END, +}; + static const struct arm64_ftr_bits ftr_id_aa64pfr0[] = { ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_EXACT, ID_AA64PFR0_GIC_SHIFT, 4, 0), S_ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_ASIMD_SHIFT, 4, ID_AA64PFR0_ASIMD_NI), @@ -153,9 +160,9 @@ static const struct arm64_ftr_bits ftr_ctr[] = { /* * Linux can handle differing I-cache policies. Userspace JITs will * make use of *minLine. - * If we have differing I-cache policies, report it as the weakest - AIVIVT. + * If we have differing I-cache policies, report it as the weakest - VIPT. */ - ARM64_FTR_BITS(FTR_VISIBLE, FTR_NONSTRICT, FTR_EXACT, 14, 2, ICACHE_POLICY_AIVIVT), /* L1Ip */ + ARM64_FTR_BITS(FTR_VISIBLE, FTR_NONSTRICT, FTR_EXACT, 14, 2, ICACHE_POLICY_VIPT), /* L1Ip */ ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, 0, 4, 0), /* IminLine */ ARM64_FTR_END, }; @@ -314,7 +321,7 @@ static const struct __ftr_reg_entry { /* Op1 = 0, CRn = 0, CRm = 6 */ ARM64_FTR_REG(SYS_ID_AA64ISAR0_EL1, ftr_id_aa64isar0), - ARM64_FTR_REG(SYS_ID_AA64ISAR1_EL1, ftr_raz), + ARM64_FTR_REG(SYS_ID_AA64ISAR1_EL1, ftr_id_aa64isar1), /* Op1 = 0, CRn = 0, CRm = 7 */ ARM64_FTR_REG(SYS_ID_AA64MMFR0_EL1, ftr_id_aa64mmfr0), @@ -585,7 +592,7 @@ void update_cpu_features(int cpu, * If we have AArch32, we care about 32-bit features for compat. * If the system doesn't support AArch32, don't update them. */ - if (id_aa64pfr0_32bit_el0(read_system_reg(SYS_ID_AA64PFR0_EL1)) && + if (id_aa64pfr0_32bit_el0(read_sanitised_ftr_reg(SYS_ID_AA64PFR0_EL1)) && id_aa64pfr0_32bit_el0(info->reg_id_aa64pfr0)) { taint |= check_update_ftr_reg(SYS_ID_DFR0_EL1, cpu, @@ -636,7 +643,7 @@ void update_cpu_features(int cpu, "Unsupported CPU feature variation.\n"); } -u64 read_system_reg(u32 id) +u64 read_sanitised_ftr_reg(u32 id) { struct arm64_ftr_reg *regp = get_arm64_ftr_reg(id); @@ -649,10 +656,10 @@ u64 read_system_reg(u32 id) case r: return read_sysreg_s(r) /* - * __raw_read_system_reg() - Used by a STARTING cpu before cpuinfo is populated. + * __read_sysreg_by_encoding() - Used by a STARTING cpu before cpuinfo is populated. * Read the system register on the current CPU */ -static u64 __raw_read_system_reg(u32 sys_id) +static u64 __read_sysreg_by_encoding(u32 sys_id) { switch (sys_id) { read_sysreg_case(SYS_ID_PFR0_EL1); @@ -709,9 +716,9 @@ has_cpuid_feature(const struct arm64_cpu_capabilities *entry, int scope) WARN_ON(scope == SCOPE_LOCAL_CPU && preemptible()); if (scope == SCOPE_SYSTEM) - val = read_system_reg(entry->sys_reg); + val = read_sanitised_ftr_reg(entry->sys_reg); else - val = __raw_read_system_reg(entry->sys_reg); + val = __read_sysreg_by_encoding(entry->sys_reg); return feature_matches(val, entry); } @@ -761,7 +768,7 @@ static bool hyp_offset_low(const struct arm64_cpu_capabilities *entry, static bool has_no_fpsimd(const struct arm64_cpu_capabilities *entry, int __unused) { - u64 pfr0 = read_system_reg(SYS_ID_AA64PFR0_EL1); + u64 pfr0 = read_sanitised_ftr_reg(SYS_ID_AA64PFR0_EL1); return cpuid_feature_extract_signed_field(pfr0, ID_AA64PFR0_FP_SHIFT) < 0; @@ -888,6 +895,9 @@ static const struct arm64_cpu_capabilities arm64_elf_hwcaps[] = { HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_FP_SHIFT, FTR_SIGNED, 1, CAP_HWCAP, HWCAP_FPHP), HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_ASIMD_SHIFT, FTR_SIGNED, 0, CAP_HWCAP, HWCAP_ASIMD), HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_ASIMD_SHIFT, FTR_SIGNED, 1, CAP_HWCAP, HWCAP_ASIMDHP), + HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_JSCVT_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, HWCAP_JSCVT), + HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_FCMA_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, HWCAP_FCMA), + HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_LRCPC_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, HWCAP_LRCPC), {}, }; diff --git a/arch/arm64/kernel/cpuinfo.c b/arch/arm64/kernel/cpuinfo.c index 5b22c687f02a..68b1f364c515 100644 --- a/arch/arm64/kernel/cpuinfo.c +++ b/arch/arm64/kernel/cpuinfo.c @@ -15,7 +15,7 @@ * along with this program. If not, see <http://www.gnu.org/licenses/>. */ #include <asm/arch_timer.h> -#include <asm/cachetype.h> +#include <asm/cache.h> #include <asm/cpu.h> #include <asm/cputype.h> #include <asm/cpufeature.h> @@ -43,10 +43,10 @@ DEFINE_PER_CPU(struct cpuinfo_arm64, cpu_data); static struct cpuinfo_arm64 boot_cpu_data; static char *icache_policy_str[] = { - [ICACHE_POLICY_RESERVED] = "RESERVED/UNKNOWN", - [ICACHE_POLICY_AIVIVT] = "AIVIVT", - [ICACHE_POLICY_VIPT] = "VIPT", - [ICACHE_POLICY_PIPT] = "PIPT", + [0 ... ICACHE_POLICY_PIPT] = "RESERVED/UNKNOWN", + [ICACHE_POLICY_VIPT] = "VIPT", + [ICACHE_POLICY_PIPT] = "PIPT", + [ICACHE_POLICY_VPIPT] = "VPIPT", }; unsigned long __icache_flags; @@ -65,6 +65,9 @@ static const char *const hwcap_str[] = { "asimdhp", "cpuid", "asimdrdm", + "jscvt", + "fcma", + "lrcpc", NULL }; @@ -289,20 +292,18 @@ static void cpuinfo_detect_icache_policy(struct cpuinfo_arm64 *info) unsigned int cpu = smp_processor_id(); u32 l1ip = CTR_L1IP(info->reg_ctr); - if (l1ip != ICACHE_POLICY_PIPT) { - /* - * VIPT caches are non-aliasing if the VA always equals the PA - * in all bit positions that are covered by the index. This is - * the case if the size of a way (# of sets * line size) does - * not exceed PAGE_SIZE. - */ - u32 waysize = icache_get_numsets() * icache_get_linesize(); - - if (l1ip != ICACHE_POLICY_VIPT || waysize > PAGE_SIZE) - set_bit(ICACHEF_ALIASING, &__icache_flags); + switch (l1ip) { + case ICACHE_POLICY_PIPT: + break; + case ICACHE_POLICY_VPIPT: + set_bit(ICACHEF_VPIPT, &__icache_flags); + break; + default: + /* Fallthrough */ + case ICACHE_POLICY_VIPT: + /* Assume aliasing */ + set_bit(ICACHEF_ALIASING, &__icache_flags); } - if (l1ip == ICACHE_POLICY_AIVIVT) - set_bit(ICACHEF_AIVIVT, &__icache_flags); pr_info("Detected %s I-cache on CPU%d\n", icache_policy_str[l1ip], cpu); } diff --git a/arch/arm64/kernel/crash_dump.c b/arch/arm64/kernel/crash_dump.c new file mode 100644 index 000000000000..f46d57c31443 --- /dev/null +++ b/arch/arm64/kernel/crash_dump.c @@ -0,0 +1,71 @@ +/* + * Routines for doing kexec-based kdump + * + * Copyright (C) 2017 Linaro Limited + * Author: AKASHI Takahiro <takahiro.akashi@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/crash_dump.h> +#include <linux/errno.h> +#include <linux/io.h> +#include <linux/memblock.h> +#include <linux/uaccess.h> +#include <asm/memory.h> + +/** + * copy_oldmem_page() - copy one page from old kernel memory + * @pfn: page frame number to be copied + * @buf: buffer where the copied page is placed + * @csize: number of bytes to copy + * @offset: offset in bytes into the page + * @userbuf: if set, @buf is in a user address space + * + * This function copies one page from old kernel memory into buffer pointed by + * @buf. If @buf is in userspace, set @userbuf to %1. Returns number of bytes + * copied or negative error in case of failure. + */ +ssize_t copy_oldmem_page(unsigned long pfn, char *buf, + size_t csize, unsigned long offset, + int userbuf) +{ + void *vaddr; + + if (!csize) + return 0; + + vaddr = memremap(__pfn_to_phys(pfn), PAGE_SIZE, MEMREMAP_WB); + if (!vaddr) + return -ENOMEM; + + if (userbuf) { + if (copy_to_user((char __user *)buf, vaddr + offset, csize)) { + memunmap(vaddr); + return -EFAULT; + } + } else { + memcpy(buf, vaddr + offset, csize); + } + + memunmap(vaddr); + + return csize; +} + +/** + * elfcorehdr_read - read from ELF core header + * @buf: buffer where the data is placed + * @csize: number of bytes to read + * @ppos: address in the memory + * + * This function reads @count bytes from elf core header which exists + * on crash dump kernel's memory. + */ +ssize_t elfcorehdr_read(char *buf, size_t count, u64 *ppos) +{ + memcpy(buf, phys_to_virt((phys_addr_t)*ppos), count); + return count; +} diff --git a/arch/arm64/kernel/debug-monitors.c b/arch/arm64/kernel/debug-monitors.c index 32913567da08..d618e25c3de1 100644 --- a/arch/arm64/kernel/debug-monitors.c +++ b/arch/arm64/kernel/debug-monitors.c @@ -36,7 +36,7 @@ /* Determine debug architecture. */ u8 debug_monitors_arch(void) { - return cpuid_feature_extract_unsigned_field(read_system_reg(SYS_ID_AA64DFR0_EL1), + return cpuid_feature_extract_unsigned_field(read_sanitised_ftr_reg(SYS_ID_AA64DFR0_EL1), ID_AA64DFR0_DEBUGVER_SHIFT); } diff --git a/arch/arm64/kernel/efi-header.S b/arch/arm64/kernel/efi-header.S new file mode 100644 index 000000000000..613fc3000677 --- /dev/null +++ b/arch/arm64/kernel/efi-header.S @@ -0,0 +1,155 @@ +/* + * Copyright (C) 2013 - 2017 Linaro, Ltd. + * Copyright (C) 2013, 2014 Red Hat, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/pe.h> +#include <linux/sizes.h> + + .macro __EFI_PE_HEADER + .long PE_MAGIC +coff_header: + .short IMAGE_FILE_MACHINE_ARM64 // Machine + .short section_count // NumberOfSections + .long 0 // TimeDateStamp + .long 0 // PointerToSymbolTable + .long 0 // NumberOfSymbols + .short section_table - optional_header // SizeOfOptionalHeader + .short IMAGE_FILE_DEBUG_STRIPPED | \ + IMAGE_FILE_EXECUTABLE_IMAGE | \ + IMAGE_FILE_LINE_NUMS_STRIPPED // Characteristics + +optional_header: + .short PE_OPT_MAGIC_PE32PLUS // PE32+ format + .byte 0x02 // MajorLinkerVersion + .byte 0x14 // MinorLinkerVersion + .long __initdata_begin - efi_header_end // SizeOfCode + .long __pecoff_data_size // SizeOfInitializedData + .long 0 // SizeOfUninitializedData + .long __efistub_entry - _head // AddressOfEntryPoint + .long efi_header_end - _head // BaseOfCode + +extra_header_fields: + .quad 0 // ImageBase + .long SZ_4K // SectionAlignment + .long PECOFF_FILE_ALIGNMENT // FileAlignment + .short 0 // MajorOperatingSystemVersion + .short 0 // MinorOperatingSystemVersion + .short 0 // MajorImageVersion + .short 0 // MinorImageVersion + .short 0 // MajorSubsystemVersion + .short 0 // MinorSubsystemVersion + .long 0 // Win32VersionValue + + .long _end - _head // SizeOfImage + + // Everything before the kernel image is considered part of the header + .long efi_header_end - _head // SizeOfHeaders + .long 0 // CheckSum + .short IMAGE_SUBSYSTEM_EFI_APPLICATION // Subsystem + .short 0 // DllCharacteristics + .quad 0 // SizeOfStackReserve + .quad 0 // SizeOfStackCommit + .quad 0 // SizeOfHeapReserve + .quad 0 // SizeOfHeapCommit + .long 0 // LoaderFlags + .long (section_table - .) / 8 // NumberOfRvaAndSizes + + .quad 0 // ExportTable + .quad 0 // ImportTable + .quad 0 // ResourceTable + .quad 0 // ExceptionTable + .quad 0 // CertificationTable + .quad 0 // BaseRelocationTable + +#ifdef CONFIG_DEBUG_EFI + .long efi_debug_table - _head // DebugTable + .long efi_debug_table_size +#endif + + // Section table +section_table: + .ascii ".text\0\0\0" + .long __initdata_begin - efi_header_end // VirtualSize + .long efi_header_end - _head // VirtualAddress + .long __initdata_begin - efi_header_end // SizeOfRawData + .long efi_header_end - _head // PointerToRawData + + .long 0 // PointerToRelocations + .long 0 // PointerToLineNumbers + .short 0 // NumberOfRelocations + .short 0 // NumberOfLineNumbers + .long IMAGE_SCN_CNT_CODE | \ + IMAGE_SCN_MEM_READ | \ + IMAGE_SCN_MEM_EXECUTE // Characteristics + + .ascii ".data\0\0\0" + .long __pecoff_data_size // VirtualSize + .long __initdata_begin - _head // VirtualAddress + .long __pecoff_data_rawsize // SizeOfRawData + .long __initdata_begin - _head // PointerToRawData + + .long 0 // PointerToRelocations + .long 0 // PointerToLineNumbers + .short 0 // NumberOfRelocations + .short 0 // NumberOfLineNumbers + .long IMAGE_SCN_CNT_INITIALIZED_DATA | \ + IMAGE_SCN_MEM_READ | \ + IMAGE_SCN_MEM_WRITE // Characteristics + + .set section_count, (. - section_table) / 40 + +#ifdef CONFIG_DEBUG_EFI + /* + * The debug table is referenced via its Relative Virtual Address (RVA), + * which is only defined for those parts of the image that are covered + * by a section declaration. Since this header is not covered by any + * section, the debug table must be emitted elsewhere. So stick it in + * the .init.rodata section instead. + * + * Note that the EFI debug entry itself may legally have a zero RVA, + * which means we can simply put it right after the section headers. + */ + __INITRODATA + + .align 2 +efi_debug_table: + // EFI_IMAGE_DEBUG_DIRECTORY_ENTRY + .long 0 // Characteristics + .long 0 // TimeDateStamp + .short 0 // MajorVersion + .short 0 // MinorVersion + .long IMAGE_DEBUG_TYPE_CODEVIEW // Type + .long efi_debug_entry_size // SizeOfData + .long 0 // RVA + .long efi_debug_entry - _head // FileOffset + + .set efi_debug_table_size, . - efi_debug_table + .previous + +efi_debug_entry: + // EFI_IMAGE_DEBUG_CODEVIEW_NB10_ENTRY + .ascii "NB10" // Signature + .long 0 // Unknown + .long 0 // Unknown2 + .long 0 // Unknown3 + + .asciz VMLINUX_PATH + + .set efi_debug_entry_size, . - efi_debug_entry +#endif + + /* + * EFI will load .text onwards at the 4k section alignment + * described in the PE/COFF header. To ensure that instruction + * sequences using an adrp and a :lo12: immediate will function + * correctly at this alignment, we must ensure that .text is + * placed at a 4k boundary in the Image to begin with. + */ + .align 12 +efi_header_end: + .endm diff --git a/arch/arm64/kernel/entry.S b/arch/arm64/kernel/entry.S index 43512d4d7df2..b738880350f9 100644 --- a/arch/arm64/kernel/entry.S +++ b/arch/arm64/kernel/entry.S @@ -428,12 +428,13 @@ el1_da: /* * Data abort handling */ - mrs x0, far_el1 + mrs x3, far_el1 enable_dbg // re-enable interrupts if they were enabled in the aborted context tbnz x23, #7, 1f // PSR_I_BIT enable_irq 1: + clear_address_tag x0, x3 mov x2, sp // struct pt_regs bl do_mem_abort @@ -594,7 +595,7 @@ el0_da: // enable interrupts before calling the main handler enable_dbg_and_irq ct_user_exit - bic x0, x26, #(0xff << 56) + clear_address_tag x0, x26 mov x1, x25 mov x2, sp bl do_mem_abort diff --git a/arch/arm64/kernel/head.S b/arch/arm64/kernel/head.S index 4fb6ccd886d1..973df7de7bf8 100644 --- a/arch/arm64/kernel/head.S +++ b/arch/arm64/kernel/head.S @@ -42,6 +42,8 @@ #include <asm/thread_info.h> #include <asm/virt.h> +#include "efi-header.S" + #define __PHYS_OFFSET (KERNEL_START - TEXT_OFFSET) #if (TEXT_OFFSET & 0xfff) != 0 @@ -89,166 +91,14 @@ _head: .quad 0 // reserved .quad 0 // reserved .quad 0 // reserved - .byte 0x41 // Magic number, "ARM\x64" - .byte 0x52 - .byte 0x4d - .byte 0x64 + .ascii "ARM\x64" // Magic number #ifdef CONFIG_EFI .long pe_header - _head // Offset to the PE header. -#else - .word 0 // reserved -#endif -#ifdef CONFIG_EFI - .align 3 pe_header: - .ascii "PE" - .short 0 -coff_header: - .short 0xaa64 // AArch64 - .short 2 // nr_sections - .long 0 // TimeDateStamp - .long 0 // PointerToSymbolTable - .long 1 // NumberOfSymbols - .short section_table - optional_header // SizeOfOptionalHeader - .short 0x206 // Characteristics. - // IMAGE_FILE_DEBUG_STRIPPED | - // IMAGE_FILE_EXECUTABLE_IMAGE | - // IMAGE_FILE_LINE_NUMS_STRIPPED -optional_header: - .short 0x20b // PE32+ format - .byte 0x02 // MajorLinkerVersion - .byte 0x14 // MinorLinkerVersion - .long _end - efi_header_end // SizeOfCode - .long 0 // SizeOfInitializedData - .long 0 // SizeOfUninitializedData - .long __efistub_entry - _head // AddressOfEntryPoint - .long efi_header_end - _head // BaseOfCode - -extra_header_fields: - .quad 0 // ImageBase - .long 0x1000 // SectionAlignment - .long PECOFF_FILE_ALIGNMENT // FileAlignment - .short 0 // MajorOperatingSystemVersion - .short 0 // MinorOperatingSystemVersion - .short 0 // MajorImageVersion - .short 0 // MinorImageVersion - .short 0 // MajorSubsystemVersion - .short 0 // MinorSubsystemVersion - .long 0 // Win32VersionValue - - .long _end - _head // SizeOfImage - - // Everything before the kernel image is considered part of the header - .long efi_header_end - _head // SizeOfHeaders - .long 0 // CheckSum - .short 0xa // Subsystem (EFI application) - .short 0 // DllCharacteristics - .quad 0 // SizeOfStackReserve - .quad 0 // SizeOfStackCommit - .quad 0 // SizeOfHeapReserve - .quad 0 // SizeOfHeapCommit - .long 0 // LoaderFlags - .long (section_table - .) / 8 // NumberOfRvaAndSizes - - .quad 0 // ExportTable - .quad 0 // ImportTable - .quad 0 // ResourceTable - .quad 0 // ExceptionTable - .quad 0 // CertificationTable - .quad 0 // BaseRelocationTable - -#ifdef CONFIG_DEBUG_EFI - .long efi_debug_table - _head // DebugTable - .long efi_debug_table_size -#endif - - // Section table -section_table: - - /* - * The EFI application loader requires a relocation section - * because EFI applications must be relocatable. This is a - * dummy section as far as we are concerned. - */ - .ascii ".reloc" - .byte 0 - .byte 0 // end of 0 padding of section name - .long 0 - .long 0 - .long 0 // SizeOfRawData - .long 0 // PointerToRawData - .long 0 // PointerToRelocations - .long 0 // PointerToLineNumbers - .short 0 // NumberOfRelocations - .short 0 // NumberOfLineNumbers - .long 0x42100040 // Characteristics (section flags) - - - .ascii ".text" - .byte 0 - .byte 0 - .byte 0 // end of 0 padding of section name - .long _end - efi_header_end // VirtualSize - .long efi_header_end - _head // VirtualAddress - .long _edata - efi_header_end // SizeOfRawData - .long efi_header_end - _head // PointerToRawData - - .long 0 // PointerToRelocations (0 for executables) - .long 0 // PointerToLineNumbers (0 for executables) - .short 0 // NumberOfRelocations (0 for executables) - .short 0 // NumberOfLineNumbers (0 for executables) - .long 0xe0500020 // Characteristics (section flags) - -#ifdef CONFIG_DEBUG_EFI - /* - * The debug table is referenced via its Relative Virtual Address (RVA), - * which is only defined for those parts of the image that are covered - * by a section declaration. Since this header is not covered by any - * section, the debug table must be emitted elsewhere. So stick it in - * the .init.rodata section instead. - * - * Note that the EFI debug entry itself may legally have a zero RVA, - * which means we can simply put it right after the section headers. - */ - __INITRODATA - - .align 2 -efi_debug_table: - // EFI_IMAGE_DEBUG_DIRECTORY_ENTRY - .long 0 // Characteristics - .long 0 // TimeDateStamp - .short 0 // MajorVersion - .short 0 // MinorVersion - .long 2 // Type == EFI_IMAGE_DEBUG_TYPE_CODEVIEW - .long efi_debug_entry_size // SizeOfData - .long 0 // RVA - .long efi_debug_entry - _head // FileOffset - - .set efi_debug_table_size, . - efi_debug_table - .previous - -efi_debug_entry: - // EFI_IMAGE_DEBUG_CODEVIEW_NB10_ENTRY - .ascii "NB10" // Signature - .long 0 // Unknown - .long 0 // Unknown2 - .long 0 // Unknown3 - - .asciz VMLINUX_PATH - - .set efi_debug_entry_size, . - efi_debug_entry -#endif - - /* - * EFI will load .text onwards at the 4k section alignment - * described in the PE/COFF header. To ensure that instruction - * sequences using an adrp and a :lo12: immediate will function - * correctly at this alignment, we must ensure that .text is - * placed at a 4k boundary in the Image to begin with. - */ - .align 12 -efi_header_end: + __EFI_PE_HEADER +#else + .long 0 // reserved #endif __INIT @@ -534,13 +384,8 @@ ENTRY(kimage_vaddr) ENTRY(el2_setup) mrs x0, CurrentEL cmp x0, #CurrentEL_EL2 - b.ne 1f - mrs x0, sctlr_el2 -CPU_BE( orr x0, x0, #(1 << 25) ) // Set the EE bit for EL2 -CPU_LE( bic x0, x0, #(1 << 25) ) // Clear the EE bit for EL2 - msr sctlr_el2, x0 - b 2f -1: mrs x0, sctlr_el1 + b.eq 1f + mrs x0, sctlr_el1 CPU_BE( orr x0, x0, #(3 << 24) ) // Set the EE and E0E bits for EL1 CPU_LE( bic x0, x0, #(3 << 24) ) // Clear the EE and E0E bits for EL1 msr sctlr_el1, x0 @@ -548,7 +393,11 @@ CPU_LE( bic x0, x0, #(3 << 24) ) // Clear the EE and E0E bits for EL1 isb ret -2: +1: mrs x0, sctlr_el2 +CPU_BE( orr x0, x0, #(1 << 25) ) // Set the EE bit for EL2 +CPU_LE( bic x0, x0, #(1 << 25) ) // Clear the EE bit for EL2 + msr sctlr_el2, x0 + #ifdef CONFIG_ARM64_VHE /* * Check for VHE being present. For the rest of the EL2 setup, @@ -594,14 +443,14 @@ set_hcr: cmp x0, #1 b.ne 3f - mrs_s x0, ICC_SRE_EL2 + mrs_s x0, SYS_ICC_SRE_EL2 orr x0, x0, #ICC_SRE_EL2_SRE // Set ICC_SRE_EL2.SRE==1 orr x0, x0, #ICC_SRE_EL2_ENABLE // Set ICC_SRE_EL2.Enable==1 - msr_s ICC_SRE_EL2, x0 + msr_s SYS_ICC_SRE_EL2, x0 isb // Make sure SRE is now set - mrs_s x0, ICC_SRE_EL2 // Read SRE back, + mrs_s x0, SYS_ICC_SRE_EL2 // Read SRE back, tbz x0, #0, 3f // and check that it sticks - msr_s ICH_HCR_EL2, xzr // Reset ICC_HCR_EL2 to defaults + msr_s SYS_ICH_HCR_EL2, xzr // Reset ICC_HCR_EL2 to defaults 3: #endif @@ -612,26 +461,6 @@ set_hcr: msr vpidr_el2, x0 msr vmpidr_el2, x1 - /* - * When VHE is not in use, early init of EL2 and EL1 needs to be - * done here. - * When VHE _is_ in use, EL1 will not be used in the host and - * requires no configuration, and all non-hyp-specific EL2 setup - * will be done via the _EL1 system register aliases in __cpu_setup. - */ - cbnz x2, 1f - - /* sctlr_el1 */ - mov x0, #0x0800 // Set/clear RES{1,0} bits -CPU_BE( movk x0, #0x33d0, lsl #16 ) // Set EE and E0E on BE systems -CPU_LE( movk x0, #0x30d0, lsl #16 ) // Clear EE and E0E on LE systems - msr sctlr_el1, x0 - - /* Coprocessor traps. */ - mov x0, #0x33ff - msr cptr_el2, x0 // Disable copro. traps to EL2 -1: - #ifdef CONFIG_COMPAT msr hstr_el2, xzr // Disable CP15 traps to EL2 #endif @@ -668,6 +497,23 @@ CPU_LE( movk x0, #0x30d0, lsl #16 ) // Clear EE and E0E on LE systems ret install_el2_stub: + /* + * When VHE is not in use, early init of EL2 and EL1 needs to be + * done here. + * When VHE _is_ in use, EL1 will not be used in the host and + * requires no configuration, and all non-hyp-specific EL2 setup + * will be done via the _EL1 system register aliases in __cpu_setup. + */ + /* sctlr_el1 */ + mov x0, #0x0800 // Set/clear RES{1,0} bits +CPU_BE( movk x0, #0x33d0, lsl #16 ) // Set EE and E0E on BE systems +CPU_LE( movk x0, #0x30d0, lsl #16 ) // Clear EE and E0E on LE systems + msr sctlr_el1, x0 + + /* Coprocessor traps. */ + mov x0, #0x33ff + msr cptr_el2, x0 // Disable copro. traps to EL2 + /* Hypervisor stub */ adr_l x0, __hyp_stub_vectors msr vbar_el2, x0 diff --git a/arch/arm64/kernel/hibernate.c b/arch/arm64/kernel/hibernate.c index 97a7384100f3..a44e13942d30 100644 --- a/arch/arm64/kernel/hibernate.c +++ b/arch/arm64/kernel/hibernate.c @@ -28,6 +28,7 @@ #include <asm/cacheflush.h> #include <asm/cputype.h> #include <asm/irqflags.h> +#include <asm/kexec.h> #include <asm/memory.h> #include <asm/mmu_context.h> #include <asm/pgalloc.h> @@ -102,7 +103,8 @@ int pfn_is_nosave(unsigned long pfn) unsigned long nosave_begin_pfn = sym_to_pfn(&__nosave_begin); unsigned long nosave_end_pfn = sym_to_pfn(&__nosave_end - 1); - return (pfn >= nosave_begin_pfn) && (pfn <= nosave_end_pfn); + return ((pfn >= nosave_begin_pfn) && (pfn <= nosave_end_pfn)) || + crash_is_nosave(pfn); } void notrace save_processor_state(void) @@ -286,6 +288,9 @@ int swsusp_arch_suspend(void) local_dbg_save(flags); if (__cpu_suspend_enter(&state)) { + /* make the crash dump kernel image visible/saveable */ + crash_prepare_suspend(); + sleep_cpu = smp_processor_id(); ret = swsusp_save(); } else { @@ -297,6 +302,9 @@ int swsusp_arch_suspend(void) if (el2_reset_needed()) dcache_clean_range(__hyp_idmap_text_start, __hyp_idmap_text_end); + /* make the crash dump kernel image protected again */ + crash_post_resume(); + /* * Tell the hibernation core that we've just restored * the memory diff --git a/arch/arm64/kernel/hw_breakpoint.c b/arch/arm64/kernel/hw_breakpoint.c index 0296e7924240..749f81779420 100644 --- a/arch/arm64/kernel/hw_breakpoint.c +++ b/arch/arm64/kernel/hw_breakpoint.c @@ -36,6 +36,7 @@ #include <asm/traps.h> #include <asm/cputype.h> #include <asm/system_misc.h> +#include <asm/uaccess.h> /* Breakpoint currently in use for each BRP. */ static DEFINE_PER_CPU(struct perf_event *, bp_on_reg[ARM_MAX_BRP]); @@ -721,6 +722,8 @@ static u64 get_distance_from_watchpoint(unsigned long addr, u64 val, u64 wp_low, wp_high; u32 lens, lene; + addr = untagged_addr(addr); + lens = __ffs(ctrl->len); lene = __fls(ctrl->len); diff --git a/arch/arm64/kernel/hyp-stub.S b/arch/arm64/kernel/hyp-stub.S index d3b5f75e652e..e1261fbaa374 100644 --- a/arch/arm64/kernel/hyp-stub.S +++ b/arch/arm64/kernel/hyp-stub.S @@ -55,18 +55,7 @@ ENDPROC(__hyp_stub_vectors) .align 11 el1_sync: - mrs x30, esr_el2 - lsr x30, x30, #ESR_ELx_EC_SHIFT - - cmp x30, #ESR_ELx_EC_HVC64 - b.ne 9f // Not an HVC trap - - cmp x0, #HVC_GET_VECTORS - b.ne 1f - mrs x0, vbar_el2 - b 9f - -1: cmp x0, #HVC_SET_VECTORS + cmp x0, #HVC_SET_VECTORS b.ne 2f msr vbar_el2, x1 b 9f @@ -79,10 +68,15 @@ el1_sync: mov x1, x3 br x4 // no return +3: cmp x0, #HVC_RESET_VECTORS + beq 9f // Nothing to reset! + /* Someone called kvm_call_hyp() against the hyp-stub... */ -3: mov x0, #ARM_EXCEPTION_HYP_GONE + ldr x0, =HVC_STUB_ERR + eret -9: eret +9: mov x0, xzr + eret ENDPROC(el1_sync) .macro invalid_vector label @@ -121,19 +115,15 @@ ENDPROC(\label) * initialisation entry point. */ -ENTRY(__hyp_get_vectors) - str lr, [sp, #-16]! - mov x0, #HVC_GET_VECTORS - hvc #0 - ldr lr, [sp], #16 - ret -ENDPROC(__hyp_get_vectors) - ENTRY(__hyp_set_vectors) - str lr, [sp, #-16]! mov x1, x0 mov x0, #HVC_SET_VECTORS hvc #0 - ldr lr, [sp], #16 ret ENDPROC(__hyp_set_vectors) + +ENTRY(__hyp_reset_vectors) + mov x0, #HVC_RESET_VECTORS + hvc #0 + ret +ENDPROC(__hyp_reset_vectors) diff --git a/arch/arm64/kernel/insn.c b/arch/arm64/kernel/insn.c index 3a63954a8b14..b884a926a632 100644 --- a/arch/arm64/kernel/insn.c +++ b/arch/arm64/kernel/insn.c @@ -474,6 +474,7 @@ static u32 aarch64_insn_encode_register(enum aarch64_insn_register_type type, shift = 10; break; case AARCH64_INSN_REGTYPE_RM: + case AARCH64_INSN_REGTYPE_RS: shift = 16; break; default: @@ -757,6 +758,111 @@ u32 aarch64_insn_gen_load_store_pair(enum aarch64_insn_register reg1, offset >> shift); } +u32 aarch64_insn_gen_load_store_ex(enum aarch64_insn_register reg, + enum aarch64_insn_register base, + enum aarch64_insn_register state, + enum aarch64_insn_size_type size, + enum aarch64_insn_ldst_type type) +{ + u32 insn; + + switch (type) { + case AARCH64_INSN_LDST_LOAD_EX: + insn = aarch64_insn_get_load_ex_value(); + break; + case AARCH64_INSN_LDST_STORE_EX: + insn = aarch64_insn_get_store_ex_value(); + break; + default: + pr_err("%s: unknown load/store exclusive encoding %d\n", __func__, type); + return AARCH64_BREAK_FAULT; + } + + insn = aarch64_insn_encode_ldst_size(size, insn); + + insn = aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RT, insn, + reg); + + insn = aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RN, insn, + base); + + insn = aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RT2, insn, + AARCH64_INSN_REG_ZR); + + return aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RS, insn, + state); +} + +static u32 aarch64_insn_encode_prfm_imm(enum aarch64_insn_prfm_type type, + enum aarch64_insn_prfm_target target, + enum aarch64_insn_prfm_policy policy, + u32 insn) +{ + u32 imm_type = 0, imm_target = 0, imm_policy = 0; + + switch (type) { + case AARCH64_INSN_PRFM_TYPE_PLD: + break; + case AARCH64_INSN_PRFM_TYPE_PLI: + imm_type = BIT(0); + break; + case AARCH64_INSN_PRFM_TYPE_PST: + imm_type = BIT(1); + break; + default: + pr_err("%s: unknown prfm type encoding %d\n", __func__, type); + return AARCH64_BREAK_FAULT; + } + + switch (target) { + case AARCH64_INSN_PRFM_TARGET_L1: + break; + case AARCH64_INSN_PRFM_TARGET_L2: + imm_target = BIT(0); + break; + case AARCH64_INSN_PRFM_TARGET_L3: + imm_target = BIT(1); + break; + default: + pr_err("%s: unknown prfm target encoding %d\n", __func__, target); + return AARCH64_BREAK_FAULT; + } + + switch (policy) { + case AARCH64_INSN_PRFM_POLICY_KEEP: + break; + case AARCH64_INSN_PRFM_POLICY_STRM: + imm_policy = BIT(0); + break; + default: + pr_err("%s: unknown prfm policy encoding %d\n", __func__, policy); + return AARCH64_BREAK_FAULT; + } + + /* In this case, imm5 is encoded into Rt field. */ + insn &= ~GENMASK(4, 0); + insn |= imm_policy | (imm_target << 1) | (imm_type << 3); + + return insn; +} + +u32 aarch64_insn_gen_prefetch(enum aarch64_insn_register base, + enum aarch64_insn_prfm_type type, + enum aarch64_insn_prfm_target target, + enum aarch64_insn_prfm_policy policy) +{ + u32 insn = aarch64_insn_get_prfm_value(); + + insn = aarch64_insn_encode_ldst_size(AARCH64_INSN_SIZE_64, insn); + + insn = aarch64_insn_encode_prfm_imm(type, target, policy, insn); + + insn = aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RN, insn, + base); + + return aarch64_insn_encode_immediate(AARCH64_INSN_IMM_12, insn, 0); +} + u32 aarch64_insn_gen_add_sub_imm(enum aarch64_insn_register dst, enum aarch64_insn_register src, int imm, enum aarch64_insn_variant variant, diff --git a/arch/arm64/kernel/machine_kexec.c b/arch/arm64/kernel/machine_kexec.c index bc96c8a7fc79..481f54a866c5 100644 --- a/arch/arm64/kernel/machine_kexec.c +++ b/arch/arm64/kernel/machine_kexec.c @@ -9,12 +9,19 @@ * published by the Free Software Foundation. */ +#include <linux/interrupt.h> +#include <linux/irq.h> +#include <linux/kernel.h> #include <linux/kexec.h> +#include <linux/page-flags.h> #include <linux/smp.h> #include <asm/cacheflush.h> #include <asm/cpu_ops.h> +#include <asm/memory.h> +#include <asm/mmu.h> #include <asm/mmu_context.h> +#include <asm/page.h> #include "cpu-reset.h" @@ -22,8 +29,6 @@ extern const unsigned char arm64_relocate_new_kernel[]; extern const unsigned long arm64_relocate_new_kernel_size; -static unsigned long kimage_start; - /** * kexec_image_info - For debugging output. */ @@ -64,8 +69,6 @@ void machine_kexec_cleanup(struct kimage *kimage) */ int machine_kexec_prepare(struct kimage *kimage) { - kimage_start = kimage->start; - kexec_image_info(kimage); if (kimage->type != KEXEC_TYPE_CRASH && cpus_are_stuck_in_kernel()) { @@ -144,11 +147,15 @@ void machine_kexec(struct kimage *kimage) { phys_addr_t reboot_code_buffer_phys; void *reboot_code_buffer; + bool in_kexec_crash = (kimage == kexec_crash_image); + bool stuck_cpus = cpus_are_stuck_in_kernel(); /* * New cpus may have become stuck_in_kernel after we loaded the image. */ - BUG_ON(cpus_are_stuck_in_kernel() || (num_online_cpus() > 1)); + BUG_ON(!in_kexec_crash && (stuck_cpus || (num_online_cpus() > 1))); + WARN(in_kexec_crash && (stuck_cpus || smp_crash_stop_failed()), + "Some CPUs may be stale, kdump will be unreliable.\n"); reboot_code_buffer_phys = page_to_phys(kimage->control_code_page); reboot_code_buffer = phys_to_virt(reboot_code_buffer_phys); @@ -183,7 +190,7 @@ void machine_kexec(struct kimage *kimage) kexec_list_flush(kimage); /* Flush the new image if already in place. */ - if (kimage->head & IND_DONE) + if ((kimage != kexec_crash_image) && (kimage->head & IND_DONE)) kexec_segment_flush(kimage); pr_info("Bye!\n"); @@ -200,13 +207,158 @@ void machine_kexec(struct kimage *kimage) * relocation is complete. */ - cpu_soft_restart(1, reboot_code_buffer_phys, kimage->head, - kimage_start, 0); + cpu_soft_restart(kimage != kexec_crash_image, + reboot_code_buffer_phys, kimage->head, kimage->start, 0); BUG(); /* Should never get here. */ } +static void machine_kexec_mask_interrupts(void) +{ + unsigned int i; + struct irq_desc *desc; + + for_each_irq_desc(i, desc) { + struct irq_chip *chip; + int ret; + + chip = irq_desc_get_chip(desc); + if (!chip) + continue; + + /* + * First try to remove the active state. If this + * fails, try to EOI the interrupt. + */ + ret = irq_set_irqchip_state(i, IRQCHIP_STATE_ACTIVE, false); + + if (ret && irqd_irq_inprogress(&desc->irq_data) && + chip->irq_eoi) + chip->irq_eoi(&desc->irq_data); + + if (chip->irq_mask) + chip->irq_mask(&desc->irq_data); + + if (chip->irq_disable && !irqd_irq_disabled(&desc->irq_data)) + chip->irq_disable(&desc->irq_data); + } +} + +/** + * machine_crash_shutdown - shutdown non-crashing cpus and save registers + */ void machine_crash_shutdown(struct pt_regs *regs) { - /* Empty routine needed to avoid build errors. */ + local_irq_disable(); + + /* shutdown non-crashing cpus */ + smp_send_crash_stop(); + + /* for crashing cpu */ + crash_save_cpu(regs, smp_processor_id()); + machine_kexec_mask_interrupts(); + + pr_info("Starting crashdump kernel...\n"); +} + +void arch_kexec_protect_crashkres(void) +{ + int i; + + kexec_segment_flush(kexec_crash_image); + + for (i = 0; i < kexec_crash_image->nr_segments; i++) + set_memory_valid( + __phys_to_virt(kexec_crash_image->segment[i].mem), + kexec_crash_image->segment[i].memsz >> PAGE_SHIFT, 0); +} + +void arch_kexec_unprotect_crashkres(void) +{ + int i; + + for (i = 0; i < kexec_crash_image->nr_segments; i++) + set_memory_valid( + __phys_to_virt(kexec_crash_image->segment[i].mem), + kexec_crash_image->segment[i].memsz >> PAGE_SHIFT, 1); +} + +#ifdef CONFIG_HIBERNATION +/* + * To preserve the crash dump kernel image, the relevant memory segments + * should be mapped again around the hibernation. + */ +void crash_prepare_suspend(void) +{ + if (kexec_crash_image) + arch_kexec_unprotect_crashkres(); +} + +void crash_post_resume(void) +{ + if (kexec_crash_image) + arch_kexec_protect_crashkres(); +} + +/* + * crash_is_nosave + * + * Return true only if a page is part of reserved memory for crash dump kernel, + * but does not hold any data of loaded kernel image. + * + * Note that all the pages in crash dump kernel memory have been initially + * marked as Reserved in kexec_reserve_crashkres_pages(). + * + * In hibernation, the pages which are Reserved and yet "nosave" are excluded + * from the hibernation iamge. crash_is_nosave() does thich check for crash + * dump kernel and will reduce the total size of hibernation image. + */ + +bool crash_is_nosave(unsigned long pfn) +{ + int i; + phys_addr_t addr; + + if (!crashk_res.end) + return false; + + /* in reserved memory? */ + addr = __pfn_to_phys(pfn); + if ((addr < crashk_res.start) || (crashk_res.end < addr)) + return false; + + if (!kexec_crash_image) + return true; + + /* not part of loaded kernel image? */ + for (i = 0; i < kexec_crash_image->nr_segments; i++) + if (addr >= kexec_crash_image->segment[i].mem && + addr < (kexec_crash_image->segment[i].mem + + kexec_crash_image->segment[i].memsz)) + return false; + + return true; +} + +void crash_free_reserved_phys_range(unsigned long begin, unsigned long end) +{ + unsigned long addr; + struct page *page; + + for (addr = begin; addr < end; addr += PAGE_SIZE) { + page = phys_to_page(addr); + ClearPageReserved(page); + free_reserved_page(page); + } +} +#endif /* CONFIG_HIBERNATION */ + +void arch_crash_save_vmcoreinfo(void) +{ + VMCOREINFO_NUMBER(VA_BITS); + /* Please note VMCOREINFO_NUMBER() uses "%d", not "%x" */ + vmcoreinfo_append_str("NUMBER(kimage_voffset)=0x%llx\n", + kimage_voffset); + vmcoreinfo_append_str("NUMBER(PHYS_OFFSET)=0x%llx\n", + PHYS_OFFSET); } diff --git a/arch/arm64/kernel/module-plts.c b/arch/arm64/kernel/module-plts.c index 1ce90d8450ae..d05dbe658409 100644 --- a/arch/arm64/kernel/module-plts.c +++ b/arch/arm64/kernel/module-plts.c @@ -1,5 +1,5 @@ /* - * Copyright (C) 2014-2016 Linaro Ltd. <ard.biesheuvel@linaro.org> + * Copyright (C) 2014-2017 Linaro Ltd. <ard.biesheuvel@linaro.org> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -26,35 +26,21 @@ struct plt_entry { __le32 br; /* br x16 */ }; -u64 module_emit_plt_entry(struct module *mod, const Elf64_Rela *rela, +static bool in_init(const struct module *mod, void *loc) +{ + return (u64)loc - (u64)mod->init_layout.base < mod->init_layout.size; +} + +u64 module_emit_plt_entry(struct module *mod, void *loc, const Elf64_Rela *rela, Elf64_Sym *sym) { - struct plt_entry *plt = (struct plt_entry *)mod->arch.plt->sh_addr; - int i = mod->arch.plt_num_entries; + struct mod_plt_sec *pltsec = !in_init(mod, loc) ? &mod->arch.core : + &mod->arch.init; + struct plt_entry *plt = (struct plt_entry *)pltsec->plt->sh_addr; + int i = pltsec->plt_num_entries; u64 val = sym->st_value + rela->r_addend; /* - * We only emit PLT entries against undefined (SHN_UNDEF) symbols, - * which are listed in the ELF symtab section, but without a type - * or a size. - * So, similar to how the module loader uses the Elf64_Sym::st_value - * field to store the resolved addresses of undefined symbols, let's - * borrow the Elf64_Sym::st_size field (whose value is never used by - * the module loader, even for symbols that are defined) to record - * the address of a symbol's associated PLT entry as we emit it for a - * zero addend relocation (which is the only kind we have to deal with - * in practice). This allows us to find duplicates without having to - * go through the table every time. - */ - if (rela->r_addend == 0 && sym->st_size != 0) { - BUG_ON(sym->st_size < (u64)plt || sym->st_size >= (u64)&plt[i]); - return sym->st_size; - } - - mod->arch.plt_num_entries++; - BUG_ON(mod->arch.plt_num_entries > mod->arch.plt_max_entries); - - /* * MOVK/MOVN/MOVZ opcode: * +--------+------------+--------+-----------+-------------+---------+ * | sf[31] | opc[30:29] | 100101 | hw[22:21] | imm16[20:5] | Rd[4:0] | @@ -72,8 +58,19 @@ u64 module_emit_plt_entry(struct module *mod, const Elf64_Rela *rela, cpu_to_le32(0xd61f0200) }; - if (rela->r_addend == 0) - sym->st_size = (u64)&plt[i]; + /* + * Check if the entry we just created is a duplicate. Given that the + * relocations are sorted, this will be the last entry we allocated. + * (if one exists). + */ + if (i > 0 && + plt[i].mov0 == plt[i - 1].mov0 && + plt[i].mov1 == plt[i - 1].mov1 && + plt[i].mov2 == plt[i - 1].mov2) + return (u64)&plt[i - 1]; + + pltsec->plt_num_entries++; + BUG_ON(pltsec->plt_num_entries > pltsec->plt_max_entries); return (u64)&plt[i]; } @@ -104,7 +101,8 @@ static bool duplicate_rel(const Elf64_Rela *rela, int num) return num > 0 && cmp_rela(rela + num, rela + num - 1) == 0; } -static unsigned int count_plts(Elf64_Sym *syms, Elf64_Rela *rela, int num) +static unsigned int count_plts(Elf64_Sym *syms, Elf64_Rela *rela, int num, + Elf64_Word dstidx) { unsigned int ret = 0; Elf64_Sym *s; @@ -116,13 +114,17 @@ static unsigned int count_plts(Elf64_Sym *syms, Elf64_Rela *rela, int num) case R_AARCH64_CALL26: /* * We only have to consider branch targets that resolve - * to undefined symbols. This is not simply a heuristic, - * it is a fundamental limitation, since the PLT itself - * is part of the module, and needs to be within 128 MB - * as well, so modules can never grow beyond that limit. + * to symbols that are defined in a different section. + * This is not simply a heuristic, it is a fundamental + * limitation, since there is no guaranteed way to emit + * PLT entries sufficiently close to the branch if the + * section size exceeds the range of a branch + * instruction. So ignore relocations against defined + * symbols if they live in the same section as the + * relocation target. */ s = syms + ELF64_R_SYM(rela[i].r_info); - if (s->st_shndx != SHN_UNDEF) + if (s->st_shndx == dstidx) break; /* @@ -149,7 +151,8 @@ static unsigned int count_plts(Elf64_Sym *syms, Elf64_Rela *rela, int num) int module_frob_arch_sections(Elf_Ehdr *ehdr, Elf_Shdr *sechdrs, char *secstrings, struct module *mod) { - unsigned long plt_max_entries = 0; + unsigned long core_plts = 0; + unsigned long init_plts = 0; Elf64_Sym *syms = NULL; int i; @@ -158,14 +161,16 @@ int module_frob_arch_sections(Elf_Ehdr *ehdr, Elf_Shdr *sechdrs, * entries. Record the symtab address as well. */ for (i = 0; i < ehdr->e_shnum; i++) { - if (strcmp(".plt", secstrings + sechdrs[i].sh_name) == 0) - mod->arch.plt = sechdrs + i; + if (!strcmp(secstrings + sechdrs[i].sh_name, ".plt")) + mod->arch.core.plt = sechdrs + i; + else if (!strcmp(secstrings + sechdrs[i].sh_name, ".init.plt")) + mod->arch.init.plt = sechdrs + i; else if (sechdrs[i].sh_type == SHT_SYMTAB) syms = (Elf64_Sym *)sechdrs[i].sh_addr; } - if (!mod->arch.plt) { - pr_err("%s: module PLT section missing\n", mod->name); + if (!mod->arch.core.plt || !mod->arch.init.plt) { + pr_err("%s: module PLT section(s) missing\n", mod->name); return -ENOEXEC; } if (!syms) { @@ -188,14 +193,27 @@ int module_frob_arch_sections(Elf_Ehdr *ehdr, Elf_Shdr *sechdrs, /* sort by type, symbol index and addend */ sort(rels, numrels, sizeof(Elf64_Rela), cmp_rela, NULL); - plt_max_entries += count_plts(syms, rels, numrels); + if (strncmp(secstrings + dstsec->sh_name, ".init", 5) != 0) + core_plts += count_plts(syms, rels, numrels, + sechdrs[i].sh_info); + else + init_plts += count_plts(syms, rels, numrels, + sechdrs[i].sh_info); } - mod->arch.plt->sh_type = SHT_NOBITS; - mod->arch.plt->sh_flags = SHF_EXECINSTR | SHF_ALLOC; - mod->arch.plt->sh_addralign = L1_CACHE_BYTES; - mod->arch.plt->sh_size = plt_max_entries * sizeof(struct plt_entry); - mod->arch.plt_num_entries = 0; - mod->arch.plt_max_entries = plt_max_entries; + mod->arch.core.plt->sh_type = SHT_NOBITS; + mod->arch.core.plt->sh_flags = SHF_EXECINSTR | SHF_ALLOC; + mod->arch.core.plt->sh_addralign = L1_CACHE_BYTES; + mod->arch.core.plt->sh_size = (core_plts + 1) * sizeof(struct plt_entry); + mod->arch.core.plt_num_entries = 0; + mod->arch.core.plt_max_entries = core_plts; + + mod->arch.init.plt->sh_type = SHT_NOBITS; + mod->arch.init.plt->sh_flags = SHF_EXECINSTR | SHF_ALLOC; + mod->arch.init.plt->sh_addralign = L1_CACHE_BYTES; + mod->arch.init.plt->sh_size = (init_plts + 1) * sizeof(struct plt_entry); + mod->arch.init.plt_num_entries = 0; + mod->arch.init.plt_max_entries = init_plts; + return 0; } diff --git a/arch/arm64/kernel/module.c b/arch/arm64/kernel/module.c index 7f316982ce00..f035ff6fb223 100644 --- a/arch/arm64/kernel/module.c +++ b/arch/arm64/kernel/module.c @@ -32,11 +32,16 @@ void *module_alloc(unsigned long size) { + gfp_t gfp_mask = GFP_KERNEL; void *p; + /* Silence the initial allocation */ + if (IS_ENABLED(CONFIG_ARM64_MODULE_PLTS)) + gfp_mask |= __GFP_NOWARN; + p = __vmalloc_node_range(size, MODULE_ALIGN, module_alloc_base, module_alloc_base + MODULES_VSIZE, - GFP_KERNEL, PAGE_KERNEL_EXEC, 0, + gfp_mask, PAGE_KERNEL_EXEC, 0, NUMA_NO_NODE, __builtin_return_address(0)); if (!p && IS_ENABLED(CONFIG_ARM64_MODULE_PLTS) && @@ -380,7 +385,7 @@ int apply_relocate_add(Elf64_Shdr *sechdrs, if (IS_ENABLED(CONFIG_ARM64_MODULE_PLTS) && ovf == -ERANGE) { - val = module_emit_plt_entry(me, &rel[i], sym); + val = module_emit_plt_entry(me, loc, &rel[i], sym); ovf = reloc_insn_imm(RELOC_OP_PREL, loc, val, 2, 26, AARCH64_INSN_IMM_26); } diff --git a/arch/arm64/kernel/module.lds b/arch/arm64/kernel/module.lds index 8949f6c6f729..f7c9781a9d48 100644 --- a/arch/arm64/kernel/module.lds +++ b/arch/arm64/kernel/module.lds @@ -1,3 +1,4 @@ SECTIONS { .plt (NOLOAD) : { BYTE(0) } + .init.plt (NOLOAD) : { BYTE(0) } } diff --git a/arch/arm64/kernel/perf_event.c b/arch/arm64/kernel/perf_event.c index 57ae9d9ed9bb..bcc79471b38e 100644 --- a/arch/arm64/kernel/perf_event.c +++ b/arch/arm64/kernel/perf_event.c @@ -290,6 +290,12 @@ static const unsigned armv8_a53_perf_cache_map[PERF_COUNT_HW_CACHE_MAX] [C(L1I)][C(OP_READ)][C(RESULT_ACCESS)] = ARMV8_PMUV3_PERFCTR_L1I_CACHE, [C(L1I)][C(OP_READ)][C(RESULT_MISS)] = ARMV8_PMUV3_PERFCTR_L1I_CACHE_REFILL, + [C(LL)][C(OP_READ)][C(RESULT_ACCESS)] = ARMV8_PMUV3_PERFCTR_L2D_CACHE, + [C(LL)][C(OP_READ)][C(RESULT_MISS)] = ARMV8_PMUV3_PERFCTR_L2D_CACHE_REFILL, + [C(LL)][C(OP_WRITE)][C(RESULT_ACCESS)] = ARMV8_PMUV3_PERFCTR_L2D_CACHE, + [C(LL)][C(OP_WRITE)][C(RESULT_MISS)] = ARMV8_PMUV3_PERFCTR_L2D_CACHE_REFILL, + + [C(DTLB)][C(OP_READ)][C(RESULT_MISS)] = ARMV8_PMUV3_PERFCTR_L1D_TLB_REFILL, [C(ITLB)][C(OP_READ)][C(RESULT_MISS)] = ARMV8_PMUV3_PERFCTR_L1I_TLB_REFILL, [C(BPU)][C(OP_READ)][C(RESULT_ACCESS)] = ARMV8_PMUV3_PERFCTR_BR_PRED, @@ -957,10 +963,26 @@ static int armv8_vulcan_map_event(struct perf_event *event) ARMV8_PMU_EVTYPE_EVENT); } +struct armv8pmu_probe_info { + struct arm_pmu *pmu; + bool present; +}; + static void __armv8pmu_probe_pmu(void *info) { - struct arm_pmu *cpu_pmu = info; + struct armv8pmu_probe_info *probe = info; + struct arm_pmu *cpu_pmu = probe->pmu; + u64 dfr0; u32 pmceid[2]; + int pmuver; + + dfr0 = read_sysreg(id_aa64dfr0_el1); + pmuver = cpuid_feature_extract_signed_field(dfr0, + ID_AA64DFR0_PMUVER_SHIFT); + if (pmuver < 1) + return; + + probe->present = true; /* Read the nb of CNTx counters supported from PMNC */ cpu_pmu->num_events = (armv8pmu_pmcr_read() >> ARMV8_PMU_PMCR_N_SHIFT) @@ -979,13 +1001,27 @@ static void __armv8pmu_probe_pmu(void *info) static int armv8pmu_probe_pmu(struct arm_pmu *cpu_pmu) { - return smp_call_function_any(&cpu_pmu->supported_cpus, + struct armv8pmu_probe_info probe = { + .pmu = cpu_pmu, + .present = false, + }; + int ret; + + ret = smp_call_function_any(&cpu_pmu->supported_cpus, __armv8pmu_probe_pmu, - cpu_pmu, 1); + &probe, 1); + if (ret) + return ret; + + return probe.present ? 0 : -ENODEV; } -static void armv8_pmu_init(struct arm_pmu *cpu_pmu) +static int armv8_pmu_init(struct arm_pmu *cpu_pmu) { + int ret = armv8pmu_probe_pmu(cpu_pmu); + if (ret) + return ret; + cpu_pmu->handle_irq = armv8pmu_handle_irq, cpu_pmu->enable = armv8pmu_enable_event, cpu_pmu->disable = armv8pmu_disable_event, @@ -997,78 +1033,104 @@ static void armv8_pmu_init(struct arm_pmu *cpu_pmu) cpu_pmu->reset = armv8pmu_reset, cpu_pmu->max_period = (1LLU << 32) - 1, cpu_pmu->set_event_filter = armv8pmu_set_event_filter; + + return 0; } static int armv8_pmuv3_init(struct arm_pmu *cpu_pmu) { - armv8_pmu_init(cpu_pmu); + int ret = armv8_pmu_init(cpu_pmu); + if (ret) + return ret; + cpu_pmu->name = "armv8_pmuv3"; cpu_pmu->map_event = armv8_pmuv3_map_event; cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_EVENTS] = &armv8_pmuv3_events_attr_group; cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_FORMATS] = &armv8_pmuv3_format_attr_group; - return armv8pmu_probe_pmu(cpu_pmu); + + return 0; } static int armv8_a53_pmu_init(struct arm_pmu *cpu_pmu) { - armv8_pmu_init(cpu_pmu); + int ret = armv8_pmu_init(cpu_pmu); + if (ret) + return ret; + cpu_pmu->name = "armv8_cortex_a53"; cpu_pmu->map_event = armv8_a53_map_event; cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_EVENTS] = &armv8_pmuv3_events_attr_group; cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_FORMATS] = &armv8_pmuv3_format_attr_group; - return armv8pmu_probe_pmu(cpu_pmu); + + return 0; } static int armv8_a57_pmu_init(struct arm_pmu *cpu_pmu) { - armv8_pmu_init(cpu_pmu); + int ret = armv8_pmu_init(cpu_pmu); + if (ret) + return ret; + cpu_pmu->name = "armv8_cortex_a57"; cpu_pmu->map_event = armv8_a57_map_event; cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_EVENTS] = &armv8_pmuv3_events_attr_group; cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_FORMATS] = &armv8_pmuv3_format_attr_group; - return armv8pmu_probe_pmu(cpu_pmu); + + return 0; } static int armv8_a72_pmu_init(struct arm_pmu *cpu_pmu) { - armv8_pmu_init(cpu_pmu); + int ret = armv8_pmu_init(cpu_pmu); + if (ret) + return ret; + cpu_pmu->name = "armv8_cortex_a72"; cpu_pmu->map_event = armv8_a57_map_event; cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_EVENTS] = &armv8_pmuv3_events_attr_group; cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_FORMATS] = &armv8_pmuv3_format_attr_group; - return armv8pmu_probe_pmu(cpu_pmu); + + return 0; } static int armv8_thunder_pmu_init(struct arm_pmu *cpu_pmu) { - armv8_pmu_init(cpu_pmu); + int ret = armv8_pmu_init(cpu_pmu); + if (ret) + return ret; + cpu_pmu->name = "armv8_cavium_thunder"; cpu_pmu->map_event = armv8_thunder_map_event; cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_EVENTS] = &armv8_pmuv3_events_attr_group; cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_FORMATS] = &armv8_pmuv3_format_attr_group; - return armv8pmu_probe_pmu(cpu_pmu); + + return 0; } static int armv8_vulcan_pmu_init(struct arm_pmu *cpu_pmu) { - armv8_pmu_init(cpu_pmu); + int ret = armv8_pmu_init(cpu_pmu); + if (ret) + return ret; + cpu_pmu->name = "armv8_brcm_vulcan"; cpu_pmu->map_event = armv8_vulcan_map_event; cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_EVENTS] = &armv8_pmuv3_events_attr_group; cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_FORMATS] = &armv8_pmuv3_format_attr_group; - return armv8pmu_probe_pmu(cpu_pmu); + + return 0; } static const struct of_device_id armv8_pmu_of_device_ids[] = { @@ -1081,24 +1143,9 @@ static const struct of_device_id armv8_pmu_of_device_ids[] = { {}, }; -/* - * Non DT systems have their micro/arch events probed at run-time. - * A fairly complete list of generic events are provided and ones that - * aren't supported by the current PMU are disabled. - */ -static const struct pmu_probe_info armv8_pmu_probe_table[] = { - PMU_PROBE(0, 0, armv8_pmuv3_init), /* enable all defined counters */ - { /* sentinel value */ } -}; - static int armv8_pmu_device_probe(struct platform_device *pdev) { - if (acpi_disabled) - return arm_pmu_device_probe(pdev, armv8_pmu_of_device_ids, - NULL); - - return arm_pmu_device_probe(pdev, armv8_pmu_of_device_ids, - armv8_pmu_probe_table); + return arm_pmu_device_probe(pdev, armv8_pmu_of_device_ids, NULL); } static struct platform_driver armv8_pmu_driver = { @@ -1109,4 +1156,11 @@ static struct platform_driver armv8_pmu_driver = { .probe = armv8_pmu_device_probe, }; -builtin_platform_driver(armv8_pmu_driver); +static int __init armv8_pmu_driver_init(void) +{ + if (acpi_disabled) + return platform_driver_register(&armv8_pmu_driver); + else + return arm_pmu_acpi_probe(armv8_pmuv3_init); +} +device_initcall(armv8_pmu_driver_init) diff --git a/arch/arm64/kernel/process.c b/arch/arm64/kernel/process.c index 043d373b8369..ae2a835898d7 100644 --- a/arch/arm64/kernel/process.c +++ b/arch/arm64/kernel/process.c @@ -205,12 +205,10 @@ void __show_regs(struct pt_regs *regs) pr_cont("\n"); } - printk("\n"); } void show_regs(struct pt_regs * regs) { - printk("\n"); __show_regs(regs); } diff --git a/arch/arm64/kernel/reloc_test_core.c b/arch/arm64/kernel/reloc_test_core.c new file mode 100644 index 000000000000..c124752a8bd3 --- /dev/null +++ b/arch/arm64/kernel/reloc_test_core.c @@ -0,0 +1,81 @@ +/* + * Copyright (C) 2017 Linaro, Ltd. <ard.biesheuvel@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/module.h> + +int sym64_rel; + +#define SYM64_ABS_VAL 0xffff880000cccccc +#define SYM32_ABS_VAL 0xf800cccc +#define SYM16_ABS_VAL 0xf8cc + +#define __SET_ABS(name, val) asm(".globl " #name "; .set "#name ", " #val) +#define SET_ABS(name, val) __SET_ABS(name, val) + +SET_ABS(sym64_abs, SYM64_ABS_VAL); +SET_ABS(sym32_abs, SYM32_ABS_VAL); +SET_ABS(sym16_abs, SYM16_ABS_VAL); + +asmlinkage u64 absolute_data64(void); +asmlinkage u64 absolute_data32(void); +asmlinkage u64 absolute_data16(void); +asmlinkage u64 signed_movw(void); +asmlinkage u64 unsigned_movw(void); +asmlinkage u64 relative_adrp(void); +asmlinkage u64 relative_adr(void); +asmlinkage u64 relative_data64(void); +asmlinkage u64 relative_data32(void); +asmlinkage u64 relative_data16(void); + +static struct { + char name[32]; + u64 (*f)(void); + u64 expect; +} const funcs[] = { + { "R_AARCH64_ABS64", absolute_data64, UL(SYM64_ABS_VAL) }, + { "R_AARCH64_ABS32", absolute_data32, UL(SYM32_ABS_VAL) }, + { "R_AARCH64_ABS16", absolute_data16, UL(SYM16_ABS_VAL) }, + { "R_AARCH64_MOVW_SABS_Gn", signed_movw, UL(SYM64_ABS_VAL) }, + { "R_AARCH64_MOVW_UABS_Gn", unsigned_movw, UL(SYM64_ABS_VAL) }, +#ifndef CONFIG_ARM64_ERRATUM_843419 + { "R_AARCH64_ADR_PREL_PG_HI21", relative_adrp, (u64)&sym64_rel }, +#endif + { "R_AARCH64_ADR_PREL_LO21", relative_adr, (u64)&sym64_rel }, + { "R_AARCH64_PREL64", relative_data64, (u64)&sym64_rel }, + { "R_AARCH64_PREL32", relative_data32, (u64)&sym64_rel }, + { "R_AARCH64_PREL16", relative_data16, (u64)&sym64_rel }, +}; + +static int reloc_test_init(void) +{ + int i; + + pr_info("Relocation test:\n"); + pr_info("-------------------------------------------------------\n"); + + for (i = 0; i < ARRAY_SIZE(funcs); i++) { + u64 ret = funcs[i].f(); + + pr_info("%-31s 0x%016llx %s\n", funcs[i].name, ret, + ret == funcs[i].expect ? "pass" : "fail"); + if (ret != funcs[i].expect) + pr_err("Relocation failed, expected 0x%016llx, not 0x%016llx\n", + funcs[i].expect, ret); + } + return 0; +} + +static void reloc_test_exit(void) +{ +} + +module_init(reloc_test_init); +module_exit(reloc_test_exit); + +MODULE_LICENSE("GPL v2"); diff --git a/arch/arm64/kernel/reloc_test_syms.S b/arch/arm64/kernel/reloc_test_syms.S new file mode 100644 index 000000000000..e1edcefeb02d --- /dev/null +++ b/arch/arm64/kernel/reloc_test_syms.S @@ -0,0 +1,83 @@ +/* + * Copyright (C) 2017 Linaro, Ltd. <ard.biesheuvel@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <linux/linkage.h> + +ENTRY(absolute_data64) + ldr x0, 0f + ret +0: .quad sym64_abs +ENDPROC(absolute_data64) + +ENTRY(absolute_data32) + ldr w0, 0f + ret +0: .long sym32_abs +ENDPROC(absolute_data32) + +ENTRY(absolute_data16) + adr x0, 0f + ldrh w0, [x0] + ret +0: .short sym16_abs, 0 +ENDPROC(absolute_data16) + +ENTRY(signed_movw) + movz x0, #:abs_g2_s:sym64_abs + movk x0, #:abs_g1_nc:sym64_abs + movk x0, #:abs_g0_nc:sym64_abs + ret +ENDPROC(signed_movw) + +ENTRY(unsigned_movw) + movz x0, #:abs_g3:sym64_abs + movk x0, #:abs_g2_nc:sym64_abs + movk x0, #:abs_g1_nc:sym64_abs + movk x0, #:abs_g0_nc:sym64_abs + ret +ENDPROC(unsigned_movw) + +#ifndef CONFIG_ARM64_ERRATUM_843419 + +ENTRY(relative_adrp) + adrp x0, sym64_rel + add x0, x0, #:lo12:sym64_rel + ret +ENDPROC(relative_adrp) + +#endif + +ENTRY(relative_adr) + adr x0, sym64_rel + ret +ENDPROC(relative_adr) + +ENTRY(relative_data64) + adr x1, 0f + ldr x0, [x1] + add x0, x0, x1 + ret +0: .quad sym64_rel - . +ENDPROC(relative_data64) + +ENTRY(relative_data32) + adr x1, 0f + ldr w0, [x1] + add x0, x0, x1 + ret +0: .long sym64_rel - . +ENDPROC(relative_data32) + +ENTRY(relative_data16) + adr x1, 0f + ldrsh w0, [x1] + add x0, x0, x1 + ret +0: .short sym64_rel - ., 0 +ENDPROC(relative_data16) diff --git a/arch/arm64/kernel/setup.c b/arch/arm64/kernel/setup.c index 42274bda0ccb..2c822ef94f34 100644 --- a/arch/arm64/kernel/setup.c +++ b/arch/arm64/kernel/setup.c @@ -31,7 +31,6 @@ #include <linux/screen_info.h> #include <linux/init.h> #include <linux/kexec.h> -#include <linux/crash_dump.h> #include <linux/root_dev.h> #include <linux/cpu.h> #include <linux/interrupt.h> @@ -181,6 +180,7 @@ static void __init smp_build_mpidr_hash(void) static void __init setup_machine_fdt(phys_addr_t dt_phys) { void *dt_virt = fixmap_remap_fdt(dt_phys); + const char *name; if (!dt_virt || !early_init_dt_scan(dt_virt)) { pr_crit("\n" @@ -193,7 +193,9 @@ static void __init setup_machine_fdt(phys_addr_t dt_phys) cpu_relax(); } - dump_stack_set_arch_desc("%s (DT)", of_flat_dt_get_machine_name()); + name = of_flat_dt_get_machine_name(); + pr_info("Machine model: %s\n", name); + dump_stack_set_arch_desc("%s (DT)", name); } static void __init request_standard_resources(void) @@ -226,6 +228,12 @@ static void __init request_standard_resources(void) if (kernel_data.start >= res->start && kernel_data.end <= res->end) request_resource(res, &kernel_data); +#ifdef CONFIG_KEXEC_CORE + /* Userspace will find "Crash kernel" region in /proc/iomem. */ + if (crashk_res.end && crashk_res.start >= res->start && + crashk_res.end <= res->end) + request_resource(res, &crashk_res); +#endif } } diff --git a/arch/arm64/kernel/smp.c b/arch/arm64/kernel/smp.c index 9b1036570586..6e0e16a3a7d4 100644 --- a/arch/arm64/kernel/smp.c +++ b/arch/arm64/kernel/smp.c @@ -39,6 +39,7 @@ #include <linux/completion.h> #include <linux/of.h> #include <linux/irq_work.h> +#include <linux/kexec.h> #include <asm/alternative.h> #include <asm/atomic.h> @@ -76,6 +77,7 @@ enum ipi_msg_type { IPI_RESCHEDULE, IPI_CALL_FUNC, IPI_CPU_STOP, + IPI_CPU_CRASH_STOP, IPI_TIMER, IPI_IRQ_WORK, IPI_WAKEUP @@ -434,6 +436,7 @@ void __init smp_cpus_done(unsigned int max_cpus) setup_cpu_features(); hyp_mode_check(); apply_alternatives_all(); + mark_linear_text_alias_ro(); } void __init smp_prepare_boot_cpu(void) @@ -518,6 +521,13 @@ static bool bootcpu_valid __initdata; static unsigned int cpu_count = 1; #ifdef CONFIG_ACPI +static struct acpi_madt_generic_interrupt cpu_madt_gicc[NR_CPUS]; + +struct acpi_madt_generic_interrupt *acpi_cpu_get_madt_gicc(int cpu) +{ + return &cpu_madt_gicc[cpu]; +} + /* * acpi_map_gic_cpu_interface - parse processor MADT entry * @@ -552,6 +562,7 @@ acpi_map_gic_cpu_interface(struct acpi_madt_generic_interrupt *processor) return; } bootcpu_valid = true; + cpu_madt_gicc[0] = *processor; early_map_cpu_to_node(0, acpi_numa_get_nid(0, hwid)); return; } @@ -562,6 +573,8 @@ acpi_map_gic_cpu_interface(struct acpi_madt_generic_interrupt *processor) /* map the logical cpu id to cpu MPIDR */ cpu_logical_map(cpu_count) = hwid; + cpu_madt_gicc[cpu_count] = *processor; + /* * Set-up the ACPI parking protocol cpu entries * while initializing the cpu_logical_map to @@ -755,6 +768,7 @@ static const char *ipi_types[NR_IPI] __tracepoint_string = { S(IPI_RESCHEDULE, "Rescheduling interrupts"), S(IPI_CALL_FUNC, "Function call interrupts"), S(IPI_CPU_STOP, "CPU stop interrupts"), + S(IPI_CPU_CRASH_STOP, "CPU stop (for crash dump) interrupts"), S(IPI_TIMER, "Timer broadcast interrupts"), S(IPI_IRQ_WORK, "IRQ work interrupts"), S(IPI_WAKEUP, "CPU wake-up interrupts"), @@ -829,6 +843,29 @@ static void ipi_cpu_stop(unsigned int cpu) cpu_relax(); } +#ifdef CONFIG_KEXEC_CORE +static atomic_t waiting_for_crash_ipi = ATOMIC_INIT(0); +#endif + +static void ipi_cpu_crash_stop(unsigned int cpu, struct pt_regs *regs) +{ +#ifdef CONFIG_KEXEC_CORE + crash_save_cpu(regs, cpu); + + atomic_dec(&waiting_for_crash_ipi); + + local_irq_disable(); + +#ifdef CONFIG_HOTPLUG_CPU + if (cpu_ops[cpu]->cpu_die) + cpu_ops[cpu]->cpu_die(cpu); +#endif + + /* just in case */ + cpu_park_loop(); +#endif +} + /* * Main handler for inter-processor interrupts */ @@ -859,6 +896,15 @@ void handle_IPI(int ipinr, struct pt_regs *regs) irq_exit(); break; + case IPI_CPU_CRASH_STOP: + if (IS_ENABLED(CONFIG_KEXEC_CORE)) { + irq_enter(); + ipi_cpu_crash_stop(cpu, regs); + + unreachable(); + } + break; + #ifdef CONFIG_GENERIC_CLOCKEVENTS_BROADCAST case IPI_TIMER: irq_enter(); @@ -931,6 +977,39 @@ void smp_send_stop(void) cpumask_pr_args(cpu_online_mask)); } +#ifdef CONFIG_KEXEC_CORE +void smp_send_crash_stop(void) +{ + cpumask_t mask; + unsigned long timeout; + + if (num_online_cpus() == 1) + return; + + cpumask_copy(&mask, cpu_online_mask); + cpumask_clear_cpu(smp_processor_id(), &mask); + + atomic_set(&waiting_for_crash_ipi, num_online_cpus() - 1); + + pr_crit("SMP: stopping secondary CPUs\n"); + smp_cross_call(&mask, IPI_CPU_CRASH_STOP); + + /* Wait up to one second for other CPUs to stop */ + timeout = USEC_PER_SEC; + while ((atomic_read(&waiting_for_crash_ipi) > 0) && timeout--) + udelay(1); + + if (atomic_read(&waiting_for_crash_ipi) > 0) + pr_warning("SMP: failed to stop secondary CPUs %*pbl\n", + cpumask_pr_args(&mask)); +} + +bool smp_crash_stop_failed(void) +{ + return (atomic_read(&waiting_for_crash_ipi) > 0); +} +#endif + /* * not supported here */ diff --git a/arch/arm64/kernel/traps.c b/arch/arm64/kernel/traps.c index 1de444e6c669..0805b44f986a 100644 --- a/arch/arm64/kernel/traps.c +++ b/arch/arm64/kernel/traps.c @@ -443,7 +443,7 @@ int cpu_enable_cache_maint_trap(void *__unused) } #define __user_cache_maint(insn, address, res) \ - if (untagged_addr(address) >= user_addr_max()) { \ + if (address >= user_addr_max()) { \ res = -EFAULT; \ } else { \ uaccess_ttbr0_enable(); \ @@ -469,7 +469,7 @@ static void user_cache_maint_handler(unsigned int esr, struct pt_regs *regs) int crm = (esr & ESR_ELx_SYS64_ISS_CRM_MASK) >> ESR_ELx_SYS64_ISS_CRM_SHIFT; int ret = 0; - address = pt_regs_read_reg(regs, rt); + address = untagged_addr(pt_regs_read_reg(regs, rt)); switch (crm) { case ESR_ELx_SYS64_ISS_CRM_DC_CVAU: /* DC CVAU, gets promoted */ @@ -513,6 +513,14 @@ static void cntvct_read_handler(unsigned int esr, struct pt_regs *regs) regs->pc += 4; } +static void cntfrq_read_handler(unsigned int esr, struct pt_regs *regs) +{ + int rt = (esr & ESR_ELx_SYS64_ISS_RT_MASK) >> ESR_ELx_SYS64_ISS_RT_SHIFT; + + pt_regs_write_reg(regs, rt, read_sysreg(cntfrq_el0)); + regs->pc += 4; +} + struct sys64_hook { unsigned int esr_mask; unsigned int esr_val; @@ -537,6 +545,12 @@ static struct sys64_hook sys64_hooks[] = { .esr_val = ESR_ELx_SYS64_ISS_SYS_CNTVCT, .handler = cntvct_read_handler, }, + { + /* Trap read access to CNTFRQ_EL0 */ + .esr_mask = ESR_ELx_SYS64_ISS_SYS_OP_MASK, + .esr_val = ESR_ELx_SYS64_ISS_SYS_CNTFRQ, + .handler = cntfrq_read_handler, + }, {}, }; diff --git a/arch/arm64/kernel/vmlinux.lds.S b/arch/arm64/kernel/vmlinux.lds.S index b8deffa9e1bf..987a00ee446c 100644 --- a/arch/arm64/kernel/vmlinux.lds.S +++ b/arch/arm64/kernel/vmlinux.lds.S @@ -143,12 +143,27 @@ SECTIONS . = ALIGN(SEGMENT_ALIGN); __init_begin = .; + __inittext_begin = .; INIT_TEXT_SECTION(8) .exit.text : { ARM_EXIT_KEEP(EXIT_TEXT) } + . = ALIGN(4); + .altinstructions : { + __alt_instructions = .; + *(.altinstructions) + __alt_instructions_end = .; + } + .altinstr_replacement : { + *(.altinstr_replacement) + } + + . = ALIGN(PAGE_SIZE); + __inittext_end = .; + __initdata_begin = .; + .init.data : { INIT_DATA INIT_SETUP(16) @@ -164,15 +179,6 @@ SECTIONS PERCPU_SECTION(L1_CACHE_BYTES) - . = ALIGN(4); - .altinstructions : { - __alt_instructions = .; - *(.altinstructions) - __alt_instructions_end = .; - } - .altinstr_replacement : { - *(.altinstr_replacement) - } .rela : ALIGN(8) { *(.rela .rela*) } @@ -181,6 +187,7 @@ SECTIONS __rela_size = SIZEOF(.rela); . = ALIGN(SEGMENT_ALIGN); + __initdata_end = .; __init_end = .; _data = .; @@ -206,6 +213,7 @@ SECTIONS } PECOFF_EDATA_PADDING + __pecoff_data_rawsize = ABSOLUTE(. - __initdata_begin); _edata = .; BSS_SECTION(0, 0, 0) @@ -221,6 +229,7 @@ SECTIONS . += RESERVED_TTBR0_SIZE; #endif + __pecoff_data_size = ABSOLUTE(. - __initdata_begin); _end = .; STABS_DEBUG diff --git a/arch/arm64/kvm/Makefile b/arch/arm64/kvm/Makefile index afd51bebb9c5..5d9810086c25 100644 --- a/arch/arm64/kvm/Makefile +++ b/arch/arm64/kvm/Makefile @@ -7,14 +7,13 @@ CFLAGS_arm.o := -I. CFLAGS_mmu.o := -I. KVM=../../../virt/kvm -ARM=../../../arch/arm/kvm obj-$(CONFIG_KVM_ARM_HOST) += kvm.o obj-$(CONFIG_KVM_ARM_HOST) += hyp/ kvm-$(CONFIG_KVM_ARM_HOST) += $(KVM)/kvm_main.o $(KVM)/coalesced_mmio.o $(KVM)/eventfd.o $(KVM)/vfio.o -kvm-$(CONFIG_KVM_ARM_HOST) += $(ARM)/arm.o $(ARM)/mmu.o $(ARM)/mmio.o -kvm-$(CONFIG_KVM_ARM_HOST) += $(ARM)/psci.o $(ARM)/perf.o +kvm-$(CONFIG_KVM_ARM_HOST) += $(KVM)/arm/arm.o $(KVM)/arm/mmu.o $(KVM)/arm/mmio.o +kvm-$(CONFIG_KVM_ARM_HOST) += $(KVM)/arm/psci.o $(KVM)/arm/perf.o kvm-$(CONFIG_KVM_ARM_HOST) += inject_fault.o regmap.o kvm-$(CONFIG_KVM_ARM_HOST) += hyp.o hyp-init.o handle_exit.o diff --git a/arch/arm64/kvm/hyp-init.S b/arch/arm64/kvm/hyp-init.S index 6b29d3d9e1f2..839425c24b1c 100644 --- a/arch/arm64/kvm/hyp-init.S +++ b/arch/arm64/kvm/hyp-init.S @@ -22,6 +22,7 @@ #include <asm/kvm_mmu.h> #include <asm/pgtable-hwdef.h> #include <asm/sysreg.h> +#include <asm/virt.h> .text .pushsection .hyp.idmap.text, "ax" @@ -58,6 +59,9 @@ __invalid: * x2: HYP vectors */ __do_hyp_init: + /* Check for a stub HVC call */ + cmp x0, #HVC_STUB_HCALL_NR + b.lo __kvm_handle_stub_hvc msr ttbr0_el2, x0 @@ -119,23 +123,45 @@ __do_hyp_init: eret ENDPROC(__kvm_hyp_init) +ENTRY(__kvm_handle_stub_hvc) + cmp x0, #HVC_SOFT_RESTART + b.ne 1f + + /* This is where we're about to jump, staying at EL2 */ + msr elr_el2, x1 + mov x0, #(PSR_F_BIT | PSR_I_BIT | PSR_A_BIT | PSR_D_BIT | PSR_MODE_EL2h) + msr spsr_el2, x0 + + /* Shuffle the arguments, and don't come back */ + mov x0, x2 + mov x1, x3 + mov x2, x4 + b reset + +1: cmp x0, #HVC_RESET_VECTORS + b.ne 1f +reset: /* - * Reset kvm back to the hyp stub. + * Reset kvm back to the hyp stub. Do not clobber x0-x4 in + * case we coming via HVC_SOFT_RESTART. */ -ENTRY(__kvm_hyp_reset) - /* We're now in idmap, disable MMU */ - mrs x0, sctlr_el2 - ldr x1, =SCTLR_ELx_FLAGS - bic x0, x0, x1 // Clear SCTL_M and etc - msr sctlr_el2, x0 + mrs x5, sctlr_el2 + ldr x6, =SCTLR_ELx_FLAGS + bic x5, x5, x6 // Clear SCTL_M and etc + msr sctlr_el2, x5 isb /* Install stub vectors */ - adr_l x0, __hyp_stub_vectors - msr vbar_el2, x0 + adr_l x5, __hyp_stub_vectors + msr vbar_el2, x5 + mov x0, xzr + eret +1: /* Bad stub call */ + ldr x0, =HVC_STUB_ERR eret -ENDPROC(__kvm_hyp_reset) + +ENDPROC(__kvm_handle_stub_hvc) .ltorg diff --git a/arch/arm64/kvm/hyp.S b/arch/arm64/kvm/hyp.S index 2726635dceba..952f6cb9cf72 100644 --- a/arch/arm64/kvm/hyp.S +++ b/arch/arm64/kvm/hyp.S @@ -36,15 +36,12 @@ * passed in x0. * * A function pointer with a value less than 0xfff has a special meaning, - * and is used to implement __hyp_get_vectors in the same way as in + * and is used to implement hyp stubs in the same way as in * arch/arm64/kernel/hyp_stub.S. - * HVC behaves as a 'bl' call and will clobber lr. */ ENTRY(__kvm_call_hyp) alternative_if_not ARM64_HAS_VIRT_HOST_EXTN - str lr, [sp, #-16]! hvc #0 - ldr lr, [sp], #16 ret alternative_else_nop_endif b __vhe_hyp_call diff --git a/arch/arm64/kvm/hyp/hyp-entry.S b/arch/arm64/kvm/hyp/hyp-entry.S index 5e9052f087f2..5170ce1021da 100644 --- a/arch/arm64/kvm/hyp/hyp-entry.S +++ b/arch/arm64/kvm/hyp/hyp-entry.S @@ -32,17 +32,17 @@ * Shuffle the parameters before calling the function * pointed to in x0. Assumes parameters in x[1,2,3]. */ + str lr, [sp, #-16]! mov lr, x0 mov x0, x1 mov x1, x2 mov x2, x3 blr lr + ldr lr, [sp], #16 .endm ENTRY(__vhe_hyp_call) - str lr, [sp, #-16]! do_el2_call - ldr lr, [sp], #16 /* * We used to rely on having an exception return to get * an implicit isb. In the E2H case, we don't have it anymore. @@ -53,21 +53,6 @@ ENTRY(__vhe_hyp_call) ret ENDPROC(__vhe_hyp_call) -/* - * Compute the idmap address of __kvm_hyp_reset based on the idmap - * start passed as a parameter, and jump there. - * - * x0: HYP phys_idmap_start - */ -ENTRY(__kvm_hyp_teardown) - mov x4, x0 - adr_l x3, __kvm_hyp_reset - - /* insert __kvm_hyp_reset()s offset into phys_idmap_start */ - bfi x4, x3, #0, #PAGE_SHIFT - br x4 -ENDPROC(__kvm_hyp_teardown) - el1_sync: // Guest trapped into EL2 stp x0, x1, [sp, #-16]! @@ -87,10 +72,24 @@ alternative_endif /* Here, we're pretty sure the host called HVC. */ ldp x0, x1, [sp], #16 - cmp x0, #HVC_GET_VECTORS - b.ne 1f - mrs x0, vbar_el2 - b 2f + /* Check for a stub HVC call */ + cmp x0, #HVC_STUB_HCALL_NR + b.hs 1f + + /* + * Compute the idmap address of __kvm_handle_stub_hvc and + * jump there. Since we use kimage_voffset, do not use the + * HYP VA for __kvm_handle_stub_hvc, but the kernel VA instead + * (by loading it from the constant pool). + * + * Preserve x0-x4, which may contain stub parameters. + */ + ldr x5, =__kvm_handle_stub_hvc + ldr_l x6, kimage_voffset + + /* x5 = __pa(x5) */ + sub x5, x5, x6 + br x5 1: /* @@ -99,7 +98,7 @@ alternative_endif kern_hyp_va x0 do_el2_call -2: eret + eret el1_trap: /* diff --git a/arch/arm64/kvm/hyp/tlb.c b/arch/arm64/kvm/hyp/tlb.c index 9e1d2b75eecd..73464a96c365 100644 --- a/arch/arm64/kvm/hyp/tlb.c +++ b/arch/arm64/kvm/hyp/tlb.c @@ -94,6 +94,28 @@ void __hyp_text __kvm_tlb_flush_vmid_ipa(struct kvm *kvm, phys_addr_t ipa) dsb(ish); isb(); + /* + * If the host is running at EL1 and we have a VPIPT I-cache, + * then we must perform I-cache maintenance at EL2 in order for + * it to have an effect on the guest. Since the guest cannot hit + * I-cache lines allocated with a different VMID, we don't need + * to worry about junk out of guest reset (we nuke the I-cache on + * VMID rollover), but we do need to be careful when remapping + * executable pages for the same guest. This can happen when KSM + * takes a CoW fault on an executable page, copies the page into + * a page that was previously mapped in the guest and then needs + * to invalidate the guest view of the I-cache for that page + * from EL1. To solve this, we invalidate the entire I-cache when + * unmapping a page from a guest if we have a VPIPT I-cache but + * the host is running at EL1. As above, we could do better if + * we had the VA. + * + * The moral of this story is: if you have a VPIPT I-cache, then + * you should be running with VHE enabled. + */ + if (!has_vhe() && icache_is_vpipt()) + __flush_icache_all(); + __tlb_switch_to_host()(kvm); } diff --git a/arch/arm64/kvm/reset.c b/arch/arm64/kvm/reset.c index d9e9697de1b2..561badf93de8 100644 --- a/arch/arm64/kvm/reset.c +++ b/arch/arm64/kvm/reset.c @@ -60,7 +60,7 @@ static bool cpu_has_32bit_el1(void) { u64 pfr0; - pfr0 = read_system_reg(SYS_ID_AA64PFR0_EL1); + pfr0 = read_sanitised_ftr_reg(SYS_ID_AA64PFR0_EL1); return !!(pfr0 & 0x20); } diff --git a/arch/arm64/kvm/sys_regs.c b/arch/arm64/kvm/sys_regs.c index 0e26f8c2b56f..0fe27024a2e1 100644 --- a/arch/arm64/kvm/sys_regs.c +++ b/arch/arm64/kvm/sys_regs.c @@ -55,6 +55,15 @@ * 64bit interface. */ +static bool read_from_write_only(struct kvm_vcpu *vcpu, + const struct sys_reg_params *params) +{ + WARN_ONCE(1, "Unexpected sys_reg read to write-only register\n"); + print_sys_reg_instr(params); + kvm_inject_undefined(vcpu); + return false; +} + /* 3 bits per cache level, as per CLIDR, but non-existent caches always 0 */ static u32 cache_levels; @@ -460,35 +469,35 @@ static void reset_pmcr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r) vcpu_sys_reg(vcpu, PMCR_EL0) = val; } -static bool pmu_access_el0_disabled(struct kvm_vcpu *vcpu) +static bool check_pmu_access_disabled(struct kvm_vcpu *vcpu, u64 flags) { u64 reg = vcpu_sys_reg(vcpu, PMUSERENR_EL0); + bool enabled = (reg & flags) || vcpu_mode_priv(vcpu); - return !((reg & ARMV8_PMU_USERENR_EN) || vcpu_mode_priv(vcpu)); + if (!enabled) + kvm_inject_undefined(vcpu); + + return !enabled; } -static bool pmu_write_swinc_el0_disabled(struct kvm_vcpu *vcpu) +static bool pmu_access_el0_disabled(struct kvm_vcpu *vcpu) { - u64 reg = vcpu_sys_reg(vcpu, PMUSERENR_EL0); + return check_pmu_access_disabled(vcpu, ARMV8_PMU_USERENR_EN); +} - return !((reg & (ARMV8_PMU_USERENR_SW | ARMV8_PMU_USERENR_EN)) - || vcpu_mode_priv(vcpu)); +static bool pmu_write_swinc_el0_disabled(struct kvm_vcpu *vcpu) +{ + return check_pmu_access_disabled(vcpu, ARMV8_PMU_USERENR_SW | ARMV8_PMU_USERENR_EN); } static bool pmu_access_cycle_counter_el0_disabled(struct kvm_vcpu *vcpu) { - u64 reg = vcpu_sys_reg(vcpu, PMUSERENR_EL0); - - return !((reg & (ARMV8_PMU_USERENR_CR | ARMV8_PMU_USERENR_EN)) - || vcpu_mode_priv(vcpu)); + return check_pmu_access_disabled(vcpu, ARMV8_PMU_USERENR_CR | ARMV8_PMU_USERENR_EN); } static bool pmu_access_event_counter_el0_disabled(struct kvm_vcpu *vcpu) { - u64 reg = vcpu_sys_reg(vcpu, PMUSERENR_EL0); - - return !((reg & (ARMV8_PMU_USERENR_ER | ARMV8_PMU_USERENR_EN)) - || vcpu_mode_priv(vcpu)); + return check_pmu_access_disabled(vcpu, ARMV8_PMU_USERENR_ER | ARMV8_PMU_USERENR_EN); } static bool access_pmcr(struct kvm_vcpu *vcpu, struct sys_reg_params *p, @@ -567,8 +576,10 @@ static bool pmu_counter_idx_valid(struct kvm_vcpu *vcpu, u64 idx) pmcr = vcpu_sys_reg(vcpu, PMCR_EL0); val = (pmcr >> ARMV8_PMU_PMCR_N_SHIFT) & ARMV8_PMU_PMCR_N_MASK; - if (idx >= val && idx != ARMV8_PMU_CYCLE_IDX) + if (idx >= val && idx != ARMV8_PMU_CYCLE_IDX) { + kvm_inject_undefined(vcpu); return false; + } return true; } @@ -707,8 +718,10 @@ static bool access_pminten(struct kvm_vcpu *vcpu, struct sys_reg_params *p, if (!kvm_arm_pmu_v3_ready(vcpu)) return trap_raz_wi(vcpu, p, r); - if (!vcpu_mode_priv(vcpu)) + if (!vcpu_mode_priv(vcpu)) { + kvm_inject_undefined(vcpu); return false; + } if (p->is_write) { u64 val = p->regval & mask; @@ -759,16 +772,15 @@ static bool access_pmswinc(struct kvm_vcpu *vcpu, struct sys_reg_params *p, if (!kvm_arm_pmu_v3_ready(vcpu)) return trap_raz_wi(vcpu, p, r); + if (!p->is_write) + return read_from_write_only(vcpu, p); + if (pmu_write_swinc_el0_disabled(vcpu)) return false; - if (p->is_write) { - mask = kvm_pmu_valid_counter_mask(vcpu); - kvm_pmu_software_increment(vcpu, p->regval & mask); - return true; - } - - return false; + mask = kvm_pmu_valid_counter_mask(vcpu); + kvm_pmu_software_increment(vcpu, p->regval & mask); + return true; } static bool access_pmuserenr(struct kvm_vcpu *vcpu, struct sys_reg_params *p, @@ -778,8 +790,10 @@ static bool access_pmuserenr(struct kvm_vcpu *vcpu, struct sys_reg_params *p, return trap_raz_wi(vcpu, p, r); if (p->is_write) { - if (!vcpu_mode_priv(vcpu)) + if (!vcpu_mode_priv(vcpu)) { + kvm_inject_undefined(vcpu); return false; + } vcpu_sys_reg(vcpu, PMUSERENR_EL0) = p->regval & ARMV8_PMU_USERENR_MASK; @@ -793,31 +807,23 @@ static bool access_pmuserenr(struct kvm_vcpu *vcpu, struct sys_reg_params *p, /* Silly macro to expand the DBG{BCR,BVR,WVR,WCR}n_EL1 registers in one go */ #define DBG_BCR_BVR_WCR_WVR_EL1(n) \ - /* DBGBVRn_EL1 */ \ - { Op0(0b10), Op1(0b000), CRn(0b0000), CRm((n)), Op2(0b100), \ + { SYS_DESC(SYS_DBGBVRn_EL1(n)), \ trap_bvr, reset_bvr, n, 0, get_bvr, set_bvr }, \ - /* DBGBCRn_EL1 */ \ - { Op0(0b10), Op1(0b000), CRn(0b0000), CRm((n)), Op2(0b101), \ + { SYS_DESC(SYS_DBGBCRn_EL1(n)), \ trap_bcr, reset_bcr, n, 0, get_bcr, set_bcr }, \ - /* DBGWVRn_EL1 */ \ - { Op0(0b10), Op1(0b000), CRn(0b0000), CRm((n)), Op2(0b110), \ + { SYS_DESC(SYS_DBGWVRn_EL1(n)), \ trap_wvr, reset_wvr, n, 0, get_wvr, set_wvr }, \ - /* DBGWCRn_EL1 */ \ - { Op0(0b10), Op1(0b000), CRn(0b0000), CRm((n)), Op2(0b111), \ + { SYS_DESC(SYS_DBGWCRn_EL1(n)), \ trap_wcr, reset_wcr, n, 0, get_wcr, set_wcr } /* Macro to expand the PMEVCNTRn_EL0 register */ #define PMU_PMEVCNTR_EL0(n) \ - /* PMEVCNTRn_EL0 */ \ - { Op0(0b11), Op1(0b011), CRn(0b1110), \ - CRm((0b1000 | (((n) >> 3) & 0x3))), Op2(((n) & 0x7)), \ + { SYS_DESC(SYS_PMEVCNTRn_EL0(n)), \ access_pmu_evcntr, reset_unknown, (PMEVCNTR0_EL0 + n), } /* Macro to expand the PMEVTYPERn_EL0 register */ #define PMU_PMEVTYPER_EL0(n) \ - /* PMEVTYPERn_EL0 */ \ - { Op0(0b11), Op1(0b011), CRn(0b1110), \ - CRm((0b1100 | (((n) >> 3) & 0x3))), Op2(((n) & 0x7)), \ + { SYS_DESC(SYS_PMEVTYPERn_EL0(n)), \ access_pmu_evtyper, reset_unknown, (PMEVTYPER0_EL0 + n), } static bool access_cntp_tval(struct kvm_vcpu *vcpu, @@ -887,24 +893,14 @@ static bool access_cntp_cval(struct kvm_vcpu *vcpu, * more demanding guest... */ static const struct sys_reg_desc sys_reg_descs[] = { - /* DC ISW */ - { Op0(0b01), Op1(0b000), CRn(0b0111), CRm(0b0110), Op2(0b010), - access_dcsw }, - /* DC CSW */ - { Op0(0b01), Op1(0b000), CRn(0b0111), CRm(0b1010), Op2(0b010), - access_dcsw }, - /* DC CISW */ - { Op0(0b01), Op1(0b000), CRn(0b0111), CRm(0b1110), Op2(0b010), - access_dcsw }, + { SYS_DESC(SYS_DC_ISW), access_dcsw }, + { SYS_DESC(SYS_DC_CSW), access_dcsw }, + { SYS_DESC(SYS_DC_CISW), access_dcsw }, DBG_BCR_BVR_WCR_WVR_EL1(0), DBG_BCR_BVR_WCR_WVR_EL1(1), - /* MDCCINT_EL1 */ - { Op0(0b10), Op1(0b000), CRn(0b0000), CRm(0b0010), Op2(0b000), - trap_debug_regs, reset_val, MDCCINT_EL1, 0 }, - /* MDSCR_EL1 */ - { Op0(0b10), Op1(0b000), CRn(0b0000), CRm(0b0010), Op2(0b010), - trap_debug_regs, reset_val, MDSCR_EL1, 0 }, + { SYS_DESC(SYS_MDCCINT_EL1), trap_debug_regs, reset_val, MDCCINT_EL1, 0 }, + { SYS_DESC(SYS_MDSCR_EL1), trap_debug_regs, reset_val, MDSCR_EL1, 0 }, DBG_BCR_BVR_WCR_WVR_EL1(2), DBG_BCR_BVR_WCR_WVR_EL1(3), DBG_BCR_BVR_WCR_WVR_EL1(4), @@ -920,179 +916,77 @@ static const struct sys_reg_desc sys_reg_descs[] = { DBG_BCR_BVR_WCR_WVR_EL1(14), DBG_BCR_BVR_WCR_WVR_EL1(15), - /* MDRAR_EL1 */ - { Op0(0b10), Op1(0b000), CRn(0b0001), CRm(0b0000), Op2(0b000), - trap_raz_wi }, - /* OSLAR_EL1 */ - { Op0(0b10), Op1(0b000), CRn(0b0001), CRm(0b0000), Op2(0b100), - trap_raz_wi }, - /* OSLSR_EL1 */ - { Op0(0b10), Op1(0b000), CRn(0b0001), CRm(0b0001), Op2(0b100), - trap_oslsr_el1 }, - /* OSDLR_EL1 */ - { Op0(0b10), Op1(0b000), CRn(0b0001), CRm(0b0011), Op2(0b100), - trap_raz_wi }, - /* DBGPRCR_EL1 */ - { Op0(0b10), Op1(0b000), CRn(0b0001), CRm(0b0100), Op2(0b100), - trap_raz_wi }, - /* DBGCLAIMSET_EL1 */ - { Op0(0b10), Op1(0b000), CRn(0b0111), CRm(0b1000), Op2(0b110), - trap_raz_wi }, - /* DBGCLAIMCLR_EL1 */ - { Op0(0b10), Op1(0b000), CRn(0b0111), CRm(0b1001), Op2(0b110), - trap_raz_wi }, - /* DBGAUTHSTATUS_EL1 */ - { Op0(0b10), Op1(0b000), CRn(0b0111), CRm(0b1110), Op2(0b110), - trap_dbgauthstatus_el1 }, - - /* MDCCSR_EL1 */ - { Op0(0b10), Op1(0b011), CRn(0b0000), CRm(0b0001), Op2(0b000), - trap_raz_wi }, - /* DBGDTR_EL0 */ - { Op0(0b10), Op1(0b011), CRn(0b0000), CRm(0b0100), Op2(0b000), - trap_raz_wi }, - /* DBGDTR[TR]X_EL0 */ - { Op0(0b10), Op1(0b011), CRn(0b0000), CRm(0b0101), Op2(0b000), - trap_raz_wi }, - - /* DBGVCR32_EL2 */ - { Op0(0b10), Op1(0b100), CRn(0b0000), CRm(0b0111), Op2(0b000), - NULL, reset_val, DBGVCR32_EL2, 0 }, - - /* MPIDR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0000), Op2(0b101), - NULL, reset_mpidr, MPIDR_EL1 }, - /* SCTLR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b0001), CRm(0b0000), Op2(0b000), - access_vm_reg, reset_val, SCTLR_EL1, 0x00C50078 }, - /* CPACR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b0001), CRm(0b0000), Op2(0b010), - NULL, reset_val, CPACR_EL1, 0 }, - /* TTBR0_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b0010), CRm(0b0000), Op2(0b000), - access_vm_reg, reset_unknown, TTBR0_EL1 }, - /* TTBR1_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b0010), CRm(0b0000), Op2(0b001), - access_vm_reg, reset_unknown, TTBR1_EL1 }, - /* TCR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b0010), CRm(0b0000), Op2(0b010), - access_vm_reg, reset_val, TCR_EL1, 0 }, - - /* AFSR0_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b0101), CRm(0b0001), Op2(0b000), - access_vm_reg, reset_unknown, AFSR0_EL1 }, - /* AFSR1_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b0101), CRm(0b0001), Op2(0b001), - access_vm_reg, reset_unknown, AFSR1_EL1 }, - /* ESR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b0101), CRm(0b0010), Op2(0b000), - access_vm_reg, reset_unknown, ESR_EL1 }, - /* FAR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b0110), CRm(0b0000), Op2(0b000), - access_vm_reg, reset_unknown, FAR_EL1 }, - /* PAR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b0111), CRm(0b0100), Op2(0b000), - NULL, reset_unknown, PAR_EL1 }, - - /* PMINTENSET_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b1001), CRm(0b1110), Op2(0b001), - access_pminten, reset_unknown, PMINTENSET_EL1 }, - /* PMINTENCLR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b1001), CRm(0b1110), Op2(0b010), - access_pminten, NULL, PMINTENSET_EL1 }, - - /* MAIR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b1010), CRm(0b0010), Op2(0b000), - access_vm_reg, reset_unknown, MAIR_EL1 }, - /* AMAIR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b1010), CRm(0b0011), Op2(0b000), - access_vm_reg, reset_amair_el1, AMAIR_EL1 }, - - /* VBAR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b1100), CRm(0b0000), Op2(0b000), - NULL, reset_val, VBAR_EL1, 0 }, - - /* ICC_SGI1R_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b1100), CRm(0b1011), Op2(0b101), - access_gic_sgi }, - /* ICC_SRE_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b1100), CRm(0b1100), Op2(0b101), - access_gic_sre }, - - /* CONTEXTIDR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b1101), CRm(0b0000), Op2(0b001), - access_vm_reg, reset_val, CONTEXTIDR_EL1, 0 }, - /* TPIDR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b1101), CRm(0b0000), Op2(0b100), - NULL, reset_unknown, TPIDR_EL1 }, - - /* CNTKCTL_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b1110), CRm(0b0001), Op2(0b000), - NULL, reset_val, CNTKCTL_EL1, 0}, - - /* CSSELR_EL1 */ - { Op0(0b11), Op1(0b010), CRn(0b0000), CRm(0b0000), Op2(0b000), - NULL, reset_unknown, CSSELR_EL1 }, - - /* PMCR_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1001), CRm(0b1100), Op2(0b000), - access_pmcr, reset_pmcr, }, - /* PMCNTENSET_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1001), CRm(0b1100), Op2(0b001), - access_pmcnten, reset_unknown, PMCNTENSET_EL0 }, - /* PMCNTENCLR_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1001), CRm(0b1100), Op2(0b010), - access_pmcnten, NULL, PMCNTENSET_EL0 }, - /* PMOVSCLR_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1001), CRm(0b1100), Op2(0b011), - access_pmovs, NULL, PMOVSSET_EL0 }, - /* PMSWINC_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1001), CRm(0b1100), Op2(0b100), - access_pmswinc, reset_unknown, PMSWINC_EL0 }, - /* PMSELR_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1001), CRm(0b1100), Op2(0b101), - access_pmselr, reset_unknown, PMSELR_EL0 }, - /* PMCEID0_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1001), CRm(0b1100), Op2(0b110), - access_pmceid }, - /* PMCEID1_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1001), CRm(0b1100), Op2(0b111), - access_pmceid }, - /* PMCCNTR_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1001), CRm(0b1101), Op2(0b000), - access_pmu_evcntr, reset_unknown, PMCCNTR_EL0 }, - /* PMXEVTYPER_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1001), CRm(0b1101), Op2(0b001), - access_pmu_evtyper }, - /* PMXEVCNTR_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1001), CRm(0b1101), Op2(0b010), - access_pmu_evcntr }, - /* PMUSERENR_EL0 - * This register resets as unknown in 64bit mode while it resets as zero + { SYS_DESC(SYS_MDRAR_EL1), trap_raz_wi }, + { SYS_DESC(SYS_OSLAR_EL1), trap_raz_wi }, + { SYS_DESC(SYS_OSLSR_EL1), trap_oslsr_el1 }, + { SYS_DESC(SYS_OSDLR_EL1), trap_raz_wi }, + { SYS_DESC(SYS_DBGPRCR_EL1), trap_raz_wi }, + { SYS_DESC(SYS_DBGCLAIMSET_EL1), trap_raz_wi }, + { SYS_DESC(SYS_DBGCLAIMCLR_EL1), trap_raz_wi }, + { SYS_DESC(SYS_DBGAUTHSTATUS_EL1), trap_dbgauthstatus_el1 }, + + { SYS_DESC(SYS_MDCCSR_EL0), trap_raz_wi }, + { SYS_DESC(SYS_DBGDTR_EL0), trap_raz_wi }, + // DBGDTR[TR]X_EL0 share the same encoding + { SYS_DESC(SYS_DBGDTRTX_EL0), trap_raz_wi }, + + { SYS_DESC(SYS_DBGVCR32_EL2), NULL, reset_val, DBGVCR32_EL2, 0 }, + + { SYS_DESC(SYS_MPIDR_EL1), NULL, reset_mpidr, MPIDR_EL1 }, + { SYS_DESC(SYS_SCTLR_EL1), access_vm_reg, reset_val, SCTLR_EL1, 0x00C50078 }, + { SYS_DESC(SYS_CPACR_EL1), NULL, reset_val, CPACR_EL1, 0 }, + { SYS_DESC(SYS_TTBR0_EL1), access_vm_reg, reset_unknown, TTBR0_EL1 }, + { SYS_DESC(SYS_TTBR1_EL1), access_vm_reg, reset_unknown, TTBR1_EL1 }, + { SYS_DESC(SYS_TCR_EL1), access_vm_reg, reset_val, TCR_EL1, 0 }, + + { SYS_DESC(SYS_AFSR0_EL1), access_vm_reg, reset_unknown, AFSR0_EL1 }, + { SYS_DESC(SYS_AFSR1_EL1), access_vm_reg, reset_unknown, AFSR1_EL1 }, + { SYS_DESC(SYS_ESR_EL1), access_vm_reg, reset_unknown, ESR_EL1 }, + { SYS_DESC(SYS_FAR_EL1), access_vm_reg, reset_unknown, FAR_EL1 }, + { SYS_DESC(SYS_PAR_EL1), NULL, reset_unknown, PAR_EL1 }, + + { SYS_DESC(SYS_PMINTENSET_EL1), access_pminten, reset_unknown, PMINTENSET_EL1 }, + { SYS_DESC(SYS_PMINTENCLR_EL1), access_pminten, NULL, PMINTENSET_EL1 }, + + { SYS_DESC(SYS_MAIR_EL1), access_vm_reg, reset_unknown, MAIR_EL1 }, + { SYS_DESC(SYS_AMAIR_EL1), access_vm_reg, reset_amair_el1, AMAIR_EL1 }, + + { SYS_DESC(SYS_VBAR_EL1), NULL, reset_val, VBAR_EL1, 0 }, + + { SYS_DESC(SYS_ICC_SGI1R_EL1), access_gic_sgi }, + { SYS_DESC(SYS_ICC_SRE_EL1), access_gic_sre }, + + { SYS_DESC(SYS_CONTEXTIDR_EL1), access_vm_reg, reset_val, CONTEXTIDR_EL1, 0 }, + { SYS_DESC(SYS_TPIDR_EL1), NULL, reset_unknown, TPIDR_EL1 }, + + { SYS_DESC(SYS_CNTKCTL_EL1), NULL, reset_val, CNTKCTL_EL1, 0}, + + { SYS_DESC(SYS_CSSELR_EL1), NULL, reset_unknown, CSSELR_EL1 }, + + { SYS_DESC(SYS_PMCR_EL0), access_pmcr, reset_pmcr, }, + { SYS_DESC(SYS_PMCNTENSET_EL0), access_pmcnten, reset_unknown, PMCNTENSET_EL0 }, + { SYS_DESC(SYS_PMCNTENCLR_EL0), access_pmcnten, NULL, PMCNTENSET_EL0 }, + { SYS_DESC(SYS_PMOVSCLR_EL0), access_pmovs, NULL, PMOVSSET_EL0 }, + { SYS_DESC(SYS_PMSWINC_EL0), access_pmswinc, reset_unknown, PMSWINC_EL0 }, + { SYS_DESC(SYS_PMSELR_EL0), access_pmselr, reset_unknown, PMSELR_EL0 }, + { SYS_DESC(SYS_PMCEID0_EL0), access_pmceid }, + { SYS_DESC(SYS_PMCEID1_EL0), access_pmceid }, + { SYS_DESC(SYS_PMCCNTR_EL0), access_pmu_evcntr, reset_unknown, PMCCNTR_EL0 }, + { SYS_DESC(SYS_PMXEVTYPER_EL0), access_pmu_evtyper }, + { SYS_DESC(SYS_PMXEVCNTR_EL0), access_pmu_evcntr }, + /* + * PMUSERENR_EL0 resets as unknown in 64bit mode while it resets as zero * in 32bit mode. Here we choose to reset it as zero for consistency. */ - { Op0(0b11), Op1(0b011), CRn(0b1001), CRm(0b1110), Op2(0b000), - access_pmuserenr, reset_val, PMUSERENR_EL0, 0 }, - /* PMOVSSET_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1001), CRm(0b1110), Op2(0b011), - access_pmovs, reset_unknown, PMOVSSET_EL0 }, - - /* TPIDR_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1101), CRm(0b0000), Op2(0b010), - NULL, reset_unknown, TPIDR_EL0 }, - /* TPIDRRO_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1101), CRm(0b0000), Op2(0b011), - NULL, reset_unknown, TPIDRRO_EL0 }, - - /* CNTP_TVAL_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1110), CRm(0b0010), Op2(0b000), - access_cntp_tval }, - /* CNTP_CTL_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1110), CRm(0b0010), Op2(0b001), - access_cntp_ctl }, - /* CNTP_CVAL_EL0 */ - { Op0(0b11), Op1(0b011), CRn(0b1110), CRm(0b0010), Op2(0b010), - access_cntp_cval }, + { SYS_DESC(SYS_PMUSERENR_EL0), access_pmuserenr, reset_val, PMUSERENR_EL0, 0 }, + { SYS_DESC(SYS_PMOVSSET_EL0), access_pmovs, reset_unknown, PMOVSSET_EL0 }, + + { SYS_DESC(SYS_TPIDR_EL0), NULL, reset_unknown, TPIDR_EL0 }, + { SYS_DESC(SYS_TPIDRRO_EL0), NULL, reset_unknown, TPIDRRO_EL0 }, + + { SYS_DESC(SYS_CNTP_TVAL_EL0), access_cntp_tval }, + { SYS_DESC(SYS_CNTP_CTL_EL0), access_cntp_ctl }, + { SYS_DESC(SYS_CNTP_CVAL_EL0), access_cntp_cval }, /* PMEVCNTRn_EL0 */ PMU_PMEVCNTR_EL0(0), @@ -1158,22 +1052,15 @@ static const struct sys_reg_desc sys_reg_descs[] = { PMU_PMEVTYPER_EL0(28), PMU_PMEVTYPER_EL0(29), PMU_PMEVTYPER_EL0(30), - /* PMCCFILTR_EL0 - * This register resets as unknown in 64bit mode while it resets as zero + /* + * PMCCFILTR_EL0 resets as unknown in 64bit mode while it resets as zero * in 32bit mode. Here we choose to reset it as zero for consistency. */ - { Op0(0b11), Op1(0b011), CRn(0b1110), CRm(0b1111), Op2(0b111), - access_pmu_evtyper, reset_val, PMCCFILTR_EL0, 0 }, - - /* DACR32_EL2 */ - { Op0(0b11), Op1(0b100), CRn(0b0011), CRm(0b0000), Op2(0b000), - NULL, reset_unknown, DACR32_EL2 }, - /* IFSR32_EL2 */ - { Op0(0b11), Op1(0b100), CRn(0b0101), CRm(0b0000), Op2(0b001), - NULL, reset_unknown, IFSR32_EL2 }, - /* FPEXC32_EL2 */ - { Op0(0b11), Op1(0b100), CRn(0b0101), CRm(0b0011), Op2(0b000), - NULL, reset_val, FPEXC32_EL2, 0x70 }, + { SYS_DESC(SYS_PMCCFILTR_EL0), access_pmu_evtyper, reset_val, PMCCFILTR_EL0, 0 }, + + { SYS_DESC(SYS_DACR32_EL2), NULL, reset_unknown, DACR32_EL2 }, + { SYS_DESC(SYS_IFSR32_EL2), NULL, reset_unknown, IFSR32_EL2 }, + { SYS_DESC(SYS_FPEXC32_EL2), NULL, reset_val, FPEXC32_EL2, 0x70 }, }; static bool trap_dbgidr(struct kvm_vcpu *vcpu, @@ -1183,8 +1070,8 @@ static bool trap_dbgidr(struct kvm_vcpu *vcpu, if (p->is_write) { return ignore_write(vcpu, p); } else { - u64 dfr = read_system_reg(SYS_ID_AA64DFR0_EL1); - u64 pfr = read_system_reg(SYS_ID_AA64PFR0_EL1); + u64 dfr = read_sanitised_ftr_reg(SYS_ID_AA64DFR0_EL1); + u64 pfr = read_sanitised_ftr_reg(SYS_ID_AA64PFR0_EL1); u32 el3 = !!cpuid_feature_extract_unsigned_field(pfr, ID_AA64PFR0_EL3_SHIFT); p->regval = ((((dfr >> ID_AA64DFR0_WRPS_SHIFT) & 0xf) << 28) | @@ -1557,6 +1444,22 @@ int kvm_handle_cp14_load_store(struct kvm_vcpu *vcpu, struct kvm_run *run) return 1; } +static void perform_access(struct kvm_vcpu *vcpu, + struct sys_reg_params *params, + const struct sys_reg_desc *r) +{ + /* + * Not having an accessor means that we have configured a trap + * that we don't know how to handle. This certainly qualifies + * as a gross bug that should be fixed right away. + */ + BUG_ON(!r->access); + + /* Skip instruction if instructed so */ + if (likely(r->access(vcpu, params, r))) + kvm_skip_instr(vcpu, kvm_vcpu_trap_il_is32bit(vcpu)); +} + /* * emulate_cp -- tries to match a sys_reg access in a handling table, and * call the corresponding trap handler. @@ -1580,20 +1483,8 @@ static int emulate_cp(struct kvm_vcpu *vcpu, r = find_reg(params, table, num); if (r) { - /* - * Not having an accessor means that we have - * configured a trap that we don't know how to - * handle. This certainly qualifies as a gross bug - * that should be fixed right away. - */ - BUG_ON(!r->access); - - if (likely(r->access(vcpu, params, r))) { - /* Skip instruction, since it was emulated */ - kvm_skip_instr(vcpu, kvm_vcpu_trap_il_is32bit(vcpu)); - /* Handled */ - return 0; - } + perform_access(vcpu, params, r); + return 0; } /* Not handled */ @@ -1638,8 +1529,8 @@ static int kvm_handle_cp_64(struct kvm_vcpu *vcpu, { struct sys_reg_params params; u32 hsr = kvm_vcpu_get_hsr(vcpu); - int Rt = (hsr >> 5) & 0xf; - int Rt2 = (hsr >> 10) & 0xf; + int Rt = kvm_vcpu_sys_get_rt(vcpu); + int Rt2 = (hsr >> 10) & 0x1f; params.is_aarch32 = true; params.is_32bit = false; @@ -1660,20 +1551,25 @@ static int kvm_handle_cp_64(struct kvm_vcpu *vcpu, params.regval |= vcpu_get_reg(vcpu, Rt2) << 32; } - if (!emulate_cp(vcpu, ¶ms, target_specific, nr_specific)) - goto out; - if (!emulate_cp(vcpu, ¶ms, global, nr_global)) - goto out; - - unhandled_cp_access(vcpu, ¶ms); + /* + * Try to emulate the coprocessor access using the target + * specific table first, and using the global table afterwards. + * If either of the tables contains a handler, handle the + * potential register operation in the case of a read and return + * with success. + */ + if (!emulate_cp(vcpu, ¶ms, target_specific, nr_specific) || + !emulate_cp(vcpu, ¶ms, global, nr_global)) { + /* Split up the value between registers for the read side */ + if (!params.is_write) { + vcpu_set_reg(vcpu, Rt, lower_32_bits(params.regval)); + vcpu_set_reg(vcpu, Rt2, upper_32_bits(params.regval)); + } -out: - /* Split up the value between registers for the read side */ - if (!params.is_write) { - vcpu_set_reg(vcpu, Rt, lower_32_bits(params.regval)); - vcpu_set_reg(vcpu, Rt2, upper_32_bits(params.regval)); + return 1; } + unhandled_cp_access(vcpu, ¶ms); return 1; } @@ -1690,7 +1586,7 @@ static int kvm_handle_cp_32(struct kvm_vcpu *vcpu, { struct sys_reg_params params; u32 hsr = kvm_vcpu_get_hsr(vcpu); - int Rt = (hsr >> 5) & 0xf; + int Rt = kvm_vcpu_sys_get_rt(vcpu); params.is_aarch32 = true; params.is_32bit = true; @@ -1763,26 +1659,13 @@ static int emulate_sys_reg(struct kvm_vcpu *vcpu, r = find_reg(params, sys_reg_descs, ARRAY_SIZE(sys_reg_descs)); if (likely(r)) { - /* - * Not having an accessor means that we have - * configured a trap that we don't know how to - * handle. This certainly qualifies as a gross bug - * that should be fixed right away. - */ - BUG_ON(!r->access); - - if (likely(r->access(vcpu, params, r))) { - /* Skip instruction, since it was emulated */ - kvm_skip_instr(vcpu, kvm_vcpu_trap_il_is32bit(vcpu)); - return 1; - } - /* If access function fails, it should complain. */ + perform_access(vcpu, params, r); } else { kvm_err("Unsupported guest sys_reg access at: %lx\n", *vcpu_pc(vcpu)); print_sys_reg_instr(params); + kvm_inject_undefined(vcpu); } - kvm_inject_undefined(vcpu); return 1; } @@ -1805,7 +1688,7 @@ int kvm_handle_sys_reg(struct kvm_vcpu *vcpu, struct kvm_run *run) { struct sys_reg_params params; unsigned long esr = kvm_vcpu_get_hsr(vcpu); - int Rt = (esr >> 5) & 0x1f; + int Rt = kvm_vcpu_sys_get_rt(vcpu); int ret; trace_kvm_handle_sys_reg(esr); @@ -1932,44 +1815,25 @@ FUNCTION_INVARIANT(aidr_el1) /* ->val is filled in by kvm_sys_reg_table_init() */ static struct sys_reg_desc invariant_sys_regs[] = { - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0000), Op2(0b000), - NULL, get_midr_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0000), Op2(0b110), - NULL, get_revidr_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0001), Op2(0b000), - NULL, get_id_pfr0_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0001), Op2(0b001), - NULL, get_id_pfr1_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0001), Op2(0b010), - NULL, get_id_dfr0_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0001), Op2(0b011), - NULL, get_id_afr0_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0001), Op2(0b100), - NULL, get_id_mmfr0_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0001), Op2(0b101), - NULL, get_id_mmfr1_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0001), Op2(0b110), - NULL, get_id_mmfr2_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0001), Op2(0b111), - NULL, get_id_mmfr3_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0010), Op2(0b000), - NULL, get_id_isar0_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0010), Op2(0b001), - NULL, get_id_isar1_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0010), Op2(0b010), - NULL, get_id_isar2_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0010), Op2(0b011), - NULL, get_id_isar3_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0010), Op2(0b100), - NULL, get_id_isar4_el1 }, - { Op0(0b11), Op1(0b000), CRn(0b0000), CRm(0b0010), Op2(0b101), - NULL, get_id_isar5_el1 }, - { Op0(0b11), Op1(0b001), CRn(0b0000), CRm(0b0000), Op2(0b001), - NULL, get_clidr_el1 }, - { Op0(0b11), Op1(0b001), CRn(0b0000), CRm(0b0000), Op2(0b111), - NULL, get_aidr_el1 }, - { Op0(0b11), Op1(0b011), CRn(0b0000), CRm(0b0000), Op2(0b001), - NULL, get_ctr_el0 }, + { SYS_DESC(SYS_MIDR_EL1), NULL, get_midr_el1 }, + { SYS_DESC(SYS_REVIDR_EL1), NULL, get_revidr_el1 }, + { SYS_DESC(SYS_ID_PFR0_EL1), NULL, get_id_pfr0_el1 }, + { SYS_DESC(SYS_ID_PFR1_EL1), NULL, get_id_pfr1_el1 }, + { SYS_DESC(SYS_ID_DFR0_EL1), NULL, get_id_dfr0_el1 }, + { SYS_DESC(SYS_ID_AFR0_EL1), NULL, get_id_afr0_el1 }, + { SYS_DESC(SYS_ID_MMFR0_EL1), NULL, get_id_mmfr0_el1 }, + { SYS_DESC(SYS_ID_MMFR1_EL1), NULL, get_id_mmfr1_el1 }, + { SYS_DESC(SYS_ID_MMFR2_EL1), NULL, get_id_mmfr2_el1 }, + { SYS_DESC(SYS_ID_MMFR3_EL1), NULL, get_id_mmfr3_el1 }, + { SYS_DESC(SYS_ID_ISAR0_EL1), NULL, get_id_isar0_el1 }, + { SYS_DESC(SYS_ID_ISAR1_EL1), NULL, get_id_isar1_el1 }, + { SYS_DESC(SYS_ID_ISAR2_EL1), NULL, get_id_isar2_el1 }, + { SYS_DESC(SYS_ID_ISAR3_EL1), NULL, get_id_isar3_el1 }, + { SYS_DESC(SYS_ID_ISAR4_EL1), NULL, get_id_isar4_el1 }, + { SYS_DESC(SYS_ID_ISAR5_EL1), NULL, get_id_isar5_el1 }, + { SYS_DESC(SYS_CLIDR_EL1), NULL, get_clidr_el1 }, + { SYS_DESC(SYS_AIDR_EL1), NULL, get_aidr_el1 }, + { SYS_DESC(SYS_CTR_EL0), NULL, get_ctr_el0 }, }; static int reg_from_user(u64 *val, const void __user *uaddr, u64 id) diff --git a/arch/arm64/kvm/sys_regs.h b/arch/arm64/kvm/sys_regs.h index 9c6ffd0f0196..060f5348ef25 100644 --- a/arch/arm64/kvm/sys_regs.h +++ b/arch/arm64/kvm/sys_regs.h @@ -83,24 +83,6 @@ static inline bool read_zero(struct kvm_vcpu *vcpu, return true; } -static inline bool write_to_read_only(struct kvm_vcpu *vcpu, - const struct sys_reg_params *params) -{ - kvm_debug("sys_reg write to read-only register at: %lx\n", - *vcpu_pc(vcpu)); - print_sys_reg_instr(params); - return false; -} - -static inline bool read_from_write_only(struct kvm_vcpu *vcpu, - const struct sys_reg_params *params) -{ - kvm_debug("sys_reg read to write-only register at: %lx\n", - *vcpu_pc(vcpu)); - print_sys_reg_instr(params); - return false; -} - /* Reset functions */ static inline void reset_unknown(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r) @@ -147,4 +129,9 @@ const struct sys_reg_desc *find_reg_by_id(u64 id, #define CRm(_x) .CRm = _x #define Op2(_x) .Op2 = _x +#define SYS_DESC(reg) \ + Op0(sys_reg_Op0(reg)), Op1(sys_reg_Op1(reg)), \ + CRn(sys_reg_CRn(reg)), CRm(sys_reg_CRm(reg)), \ + Op2(sys_reg_Op2(reg)) + #endif /* __ARM64_KVM_SYS_REGS_LOCAL_H__ */ diff --git a/arch/arm64/kvm/sys_regs_generic_v8.c b/arch/arm64/kvm/sys_regs_generic_v8.c index 46af7186bca6..969ade1d333d 100644 --- a/arch/arm64/kvm/sys_regs_generic_v8.c +++ b/arch/arm64/kvm/sys_regs_generic_v8.c @@ -52,9 +52,7 @@ static void reset_actlr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r) * Important: Must be sorted ascending by Op0, Op1, CRn, CRm, Op2 */ static const struct sys_reg_desc genericv8_sys_regs[] = { - /* ACTLR_EL1 */ - { Op0(0b11), Op1(0b000), CRn(0b0001), CRm(0b0000), Op2(0b001), - access_actlr, reset_actlr, ACTLR_EL1 }, + { SYS_DESC(SYS_ACTLR_EL1), access_actlr, reset_actlr, ACTLR_EL1 }, }; static const struct sys_reg_desc genericv8_cp15_regs[] = { diff --git a/arch/arm64/mm/context.c b/arch/arm64/mm/context.c index 68634c630cdd..ab9f5f0fb2c7 100644 --- a/arch/arm64/mm/context.c +++ b/arch/arm64/mm/context.c @@ -119,9 +119,6 @@ static void flush_context(unsigned int cpu) /* Queue a TLB invalidate and flush the I-cache if necessary. */ cpumask_setall(&tlb_flush_pending); - - if (icache_is_aivivt()) - __flush_icache_all(); } static bool check_update_reserved_asid(u64 asid, u64 newasid) diff --git a/arch/arm64/mm/dma-mapping.c b/arch/arm64/mm/dma-mapping.c index 7f8b37e85a2b..3216e098c058 100644 --- a/arch/arm64/mm/dma-mapping.c +++ b/arch/arm64/mm/dma-mapping.c @@ -28,6 +28,7 @@ #include <linux/dma-contiguous.h> #include <linux/vmalloc.h> #include <linux/swiotlb.h> +#include <linux/pci.h> #include <asm/cacheflush.h> @@ -308,24 +309,15 @@ static void __swiotlb_sync_sg_for_device(struct device *dev, sg->length, dir); } -static int __swiotlb_mmap(struct device *dev, - struct vm_area_struct *vma, - void *cpu_addr, dma_addr_t dma_addr, size_t size, - unsigned long attrs) +static int __swiotlb_mmap_pfn(struct vm_area_struct *vma, + unsigned long pfn, size_t size) { int ret = -ENXIO; unsigned long nr_vma_pages = (vma->vm_end - vma->vm_start) >> PAGE_SHIFT; unsigned long nr_pages = PAGE_ALIGN(size) >> PAGE_SHIFT; - unsigned long pfn = dma_to_phys(dev, dma_addr) >> PAGE_SHIFT; unsigned long off = vma->vm_pgoff; - vma->vm_page_prot = __get_dma_pgprot(attrs, vma->vm_page_prot, - is_device_dma_coherent(dev)); - - if (dma_mmap_from_coherent(dev, vma, cpu_addr, size, &ret)) - return ret; - if (off < nr_pages && nr_vma_pages <= (nr_pages - off)) { ret = remap_pfn_range(vma, vma->vm_start, pfn + off, @@ -336,19 +328,43 @@ static int __swiotlb_mmap(struct device *dev, return ret; } -static int __swiotlb_get_sgtable(struct device *dev, struct sg_table *sgt, - void *cpu_addr, dma_addr_t handle, size_t size, - unsigned long attrs) +static int __swiotlb_mmap(struct device *dev, + struct vm_area_struct *vma, + void *cpu_addr, dma_addr_t dma_addr, size_t size, + unsigned long attrs) +{ + int ret; + unsigned long pfn = dma_to_phys(dev, dma_addr) >> PAGE_SHIFT; + + vma->vm_page_prot = __get_dma_pgprot(attrs, vma->vm_page_prot, + is_device_dma_coherent(dev)); + + if (dma_mmap_from_coherent(dev, vma, cpu_addr, size, &ret)) + return ret; + + return __swiotlb_mmap_pfn(vma, pfn, size); +} + +static int __swiotlb_get_sgtable_page(struct sg_table *sgt, + struct page *page, size_t size) { int ret = sg_alloc_table(sgt, 1, GFP_KERNEL); if (!ret) - sg_set_page(sgt->sgl, phys_to_page(dma_to_phys(dev, handle)), - PAGE_ALIGN(size), 0); + sg_set_page(sgt->sgl, page, PAGE_ALIGN(size), 0); return ret; } +static int __swiotlb_get_sgtable(struct device *dev, struct sg_table *sgt, + void *cpu_addr, dma_addr_t handle, size_t size, + unsigned long attrs) +{ + struct page *page = phys_to_page(dma_to_phys(dev, handle)); + + return __swiotlb_get_sgtable_page(sgt, page, size); +} + static int __swiotlb_dma_supported(struct device *hwdev, u64 mask) { if (swiotlb) @@ -584,20 +600,7 @@ static void *__iommu_alloc_attrs(struct device *dev, size_t size, */ gfp |= __GFP_ZERO; - if (gfpflags_allow_blocking(gfp)) { - struct page **pages; - pgprot_t prot = __get_dma_pgprot(attrs, PAGE_KERNEL, coherent); - - pages = iommu_dma_alloc(dev, iosize, gfp, attrs, ioprot, - handle, flush_page); - if (!pages) - return NULL; - - addr = dma_common_pages_remap(pages, size, VM_USERMAP, prot, - __builtin_return_address(0)); - if (!addr) - iommu_dma_free(dev, pages, iosize, handle); - } else { + if (!gfpflags_allow_blocking(gfp)) { struct page *page; /* * In atomic context we can't remap anything, so we'll only @@ -621,6 +624,45 @@ static void *__iommu_alloc_attrs(struct device *dev, size_t size, __free_from_pool(addr, size); addr = NULL; } + } else if (attrs & DMA_ATTR_FORCE_CONTIGUOUS) { + pgprot_t prot = __get_dma_pgprot(attrs, PAGE_KERNEL, coherent); + struct page *page; + + page = dma_alloc_from_contiguous(dev, size >> PAGE_SHIFT, + get_order(size), gfp); + if (!page) + return NULL; + + *handle = iommu_dma_map_page(dev, page, 0, iosize, ioprot); + if (iommu_dma_mapping_error(dev, *handle)) { + dma_release_from_contiguous(dev, page, + size >> PAGE_SHIFT); + return NULL; + } + if (!coherent) + __dma_flush_area(page_to_virt(page), iosize); + + addr = dma_common_contiguous_remap(page, size, VM_USERMAP, + prot, + __builtin_return_address(0)); + if (!addr) { + iommu_dma_unmap_page(dev, *handle, iosize, 0, attrs); + dma_release_from_contiguous(dev, page, + size >> PAGE_SHIFT); + } + } else { + pgprot_t prot = __get_dma_pgprot(attrs, PAGE_KERNEL, coherent); + struct page **pages; + + pages = iommu_dma_alloc(dev, iosize, gfp, attrs, ioprot, + handle, flush_page); + if (!pages) + return NULL; + + addr = dma_common_pages_remap(pages, size, VM_USERMAP, prot, + __builtin_return_address(0)); + if (!addr) + iommu_dma_free(dev, pages, iosize, handle); } return addr; } @@ -632,7 +674,8 @@ static void __iommu_free_attrs(struct device *dev, size_t size, void *cpu_addr, size = PAGE_ALIGN(size); /* - * @cpu_addr will be one of 3 things depending on how it was allocated: + * @cpu_addr will be one of 4 things depending on how it was allocated: + * - A remapped array of pages for contiguous allocations. * - A remapped array of pages from iommu_dma_alloc(), for all * non-atomic allocations. * - A non-cacheable alias from the atomic pool, for atomic @@ -644,6 +687,12 @@ static void __iommu_free_attrs(struct device *dev, size_t size, void *cpu_addr, if (__in_atomic_pool(cpu_addr, size)) { iommu_dma_unmap_page(dev, handle, iosize, 0, 0); __free_from_pool(cpu_addr, size); + } else if (attrs & DMA_ATTR_FORCE_CONTIGUOUS) { + struct page *page = vmalloc_to_page(cpu_addr); + + iommu_dma_unmap_page(dev, handle, iosize, 0, attrs); + dma_release_from_contiguous(dev, page, size >> PAGE_SHIFT); + dma_common_free_remap(cpu_addr, size, VM_USERMAP); } else if (is_vmalloc_addr(cpu_addr)){ struct vm_struct *area = find_vm_area(cpu_addr); @@ -670,6 +719,15 @@ static int __iommu_mmap_attrs(struct device *dev, struct vm_area_struct *vma, if (dma_mmap_from_coherent(dev, vma, cpu_addr, size, &ret)) return ret; + if (attrs & DMA_ATTR_FORCE_CONTIGUOUS) { + /* + * DMA_ATTR_FORCE_CONTIGUOUS allocations are always remapped, + * hence in the vmalloc space. + */ + unsigned long pfn = vmalloc_to_pfn(cpu_addr); + return __swiotlb_mmap_pfn(vma, pfn, size); + } + area = find_vm_area(cpu_addr); if (WARN_ON(!area || !area->pages)) return -ENXIO; @@ -684,6 +742,15 @@ static int __iommu_get_sgtable(struct device *dev, struct sg_table *sgt, unsigned int count = PAGE_ALIGN(size) >> PAGE_SHIFT; struct vm_struct *area = find_vm_area(cpu_addr); + if (attrs & DMA_ATTR_FORCE_CONTIGUOUS) { + /* + * DMA_ATTR_FORCE_CONTIGUOUS allocations are always remapped, + * hence in the vmalloc space. + */ + struct page *page = vmalloc_to_page(cpu_addr); + return __swiotlb_get_sgtable_page(sgt, page, size); + } + if (WARN_ON(!area || !area->pages)) return -ENXIO; @@ -813,34 +880,26 @@ static const struct dma_map_ops iommu_dma_ops = { .mapping_error = iommu_dma_mapping_error, }; -/* - * TODO: Right now __iommu_setup_dma_ops() gets called too early to do - * everything it needs to - the device is only partially created and the - * IOMMU driver hasn't seen it yet, so it can't have a group. Thus we - * need this delayed attachment dance. Once IOMMU probe ordering is sorted - * to move the arch_setup_dma_ops() call later, all the notifier bits below - * become unnecessary, and will go away. - */ -struct iommu_dma_notifier_data { - struct list_head list; - struct device *dev; - const struct iommu_ops *ops; - u64 dma_base; - u64 size; -}; -static LIST_HEAD(iommu_dma_masters); -static DEFINE_MUTEX(iommu_dma_notifier_lock); +static int __init __iommu_dma_init(void) +{ + return iommu_dma_init(); +} +arch_initcall(__iommu_dma_init); -static bool do_iommu_attach(struct device *dev, const struct iommu_ops *ops, - u64 dma_base, u64 size) +static void __iommu_setup_dma_ops(struct device *dev, u64 dma_base, u64 size, + const struct iommu_ops *ops) { - struct iommu_domain *domain = iommu_get_domain_for_dev(dev); + struct iommu_domain *domain; + + if (!ops) + return; /* - * If the IOMMU driver has the DMA domain support that we require, - * then the IOMMU core will have already configured a group for this - * device, and allocated the default domain for that group. + * The IOMMU core code allocates the default DMA domain, which the + * underlying IOMMU driver needs to support via the dma-iommu layer. */ + domain = iommu_get_domain_for_dev(dev); + if (!domain) goto out_err; @@ -851,109 +910,11 @@ static bool do_iommu_attach(struct device *dev, const struct iommu_ops *ops, dev->dma_ops = &iommu_dma_ops; } - return true; + return; + out_err: - pr_warn("Failed to set up IOMMU for device %s; retaining platform DMA ops\n", + pr_warn("Failed to set up IOMMU for device %s; retaining platform DMA ops\n", dev_name(dev)); - return false; -} - -static void queue_iommu_attach(struct device *dev, const struct iommu_ops *ops, - u64 dma_base, u64 size) -{ - struct iommu_dma_notifier_data *iommudata; - - iommudata = kzalloc(sizeof(*iommudata), GFP_KERNEL); - if (!iommudata) - return; - - iommudata->dev = dev; - iommudata->ops = ops; - iommudata->dma_base = dma_base; - iommudata->size = size; - - mutex_lock(&iommu_dma_notifier_lock); - list_add(&iommudata->list, &iommu_dma_masters); - mutex_unlock(&iommu_dma_notifier_lock); -} - -static int __iommu_attach_notifier(struct notifier_block *nb, - unsigned long action, void *data) -{ - struct iommu_dma_notifier_data *master, *tmp; - - if (action != BUS_NOTIFY_BIND_DRIVER) - return 0; - - mutex_lock(&iommu_dma_notifier_lock); - list_for_each_entry_safe(master, tmp, &iommu_dma_masters, list) { - if (data == master->dev && do_iommu_attach(master->dev, - master->ops, master->dma_base, master->size)) { - list_del(&master->list); - kfree(master); - break; - } - } - mutex_unlock(&iommu_dma_notifier_lock); - return 0; -} - -static int __init register_iommu_dma_ops_notifier(struct bus_type *bus) -{ - struct notifier_block *nb = kzalloc(sizeof(*nb), GFP_KERNEL); - int ret; - - if (!nb) - return -ENOMEM; - - nb->notifier_call = __iommu_attach_notifier; - - ret = bus_register_notifier(bus, nb); - if (ret) { - pr_warn("Failed to register DMA domain notifier; IOMMU DMA ops unavailable on bus '%s'\n", - bus->name); - kfree(nb); - } - return ret; -} - -static int __init __iommu_dma_init(void) -{ - int ret; - - ret = iommu_dma_init(); - if (!ret) - ret = register_iommu_dma_ops_notifier(&platform_bus_type); - if (!ret) - ret = register_iommu_dma_ops_notifier(&amba_bustype); -#ifdef CONFIG_PCI - if (!ret) - ret = register_iommu_dma_ops_notifier(&pci_bus_type); -#endif - return ret; -} -arch_initcall(__iommu_dma_init); - -static void __iommu_setup_dma_ops(struct device *dev, u64 dma_base, u64 size, - const struct iommu_ops *ops) -{ - struct iommu_group *group; - - if (!ops) - return; - /* - * TODO: As a concession to the future, we're ready to handle being - * called both early and late (i.e. after bus_add_device). Once all - * the platform bus code is reworked to call us late and the notifier - * junk above goes away, move the body of do_iommu_attach here. - */ - group = iommu_group_get(dev); - if (group) { - do_iommu_attach(dev, ops, dma_base, size); - iommu_group_put(group); - } else { - queue_iommu_attach(dev, ops, dma_base, size); - } } void arch_teardown_dma_ops(struct device *dev) diff --git a/arch/arm64/mm/fault.c b/arch/arm64/mm/fault.c index 1b35b8bddbfb..37b95dff0b07 100644 --- a/arch/arm64/mm/fault.c +++ b/arch/arm64/mm/fault.c @@ -174,12 +174,33 @@ static bool is_el1_instruction_abort(unsigned int esr) return ESR_ELx_EC(esr) == ESR_ELx_EC_IABT_CUR; } +static inline bool is_permission_fault(unsigned int esr, struct pt_regs *regs, + unsigned long addr) +{ + unsigned int ec = ESR_ELx_EC(esr); + unsigned int fsc_type = esr & ESR_ELx_FSC_TYPE; + + if (ec != ESR_ELx_EC_DABT_CUR && ec != ESR_ELx_EC_IABT_CUR) + return false; + + if (fsc_type == ESR_ELx_FSC_PERM) + return true; + + if (addr < USER_DS && system_uses_ttbr0_pan()) + return fsc_type == ESR_ELx_FSC_FAULT && + (regs->pstate & PSR_PAN_BIT); + + return false; +} + /* * The kernel tried to access some page that wasn't present. */ static void __do_kernel_fault(struct mm_struct *mm, unsigned long addr, unsigned int esr, struct pt_regs *regs) { + const char *msg; + /* * Are we prepared to handle this kernel fault? * We are almost certainly not prepared to handle instruction faults. @@ -191,9 +212,20 @@ static void __do_kernel_fault(struct mm_struct *mm, unsigned long addr, * No handler, we'll have to terminate things with extreme prejudice. */ bust_spinlocks(1); - pr_alert("Unable to handle kernel %s at virtual address %08lx\n", - (addr < PAGE_SIZE) ? "NULL pointer dereference" : - "paging request", addr); + + if (is_permission_fault(esr, regs, addr)) { + if (esr & ESR_ELx_WNR) + msg = "write to read-only memory"; + else + msg = "read from unreadable memory"; + } else if (addr < PAGE_SIZE) { + msg = "NULL pointer dereference"; + } else { + msg = "paging request"; + } + + pr_alert("Unable to handle kernel %s at virtual address %08lx\n", msg, + addr); show_pte(mm, addr); die("Oops", regs, esr); @@ -287,21 +319,6 @@ out: return fault; } -static inline bool is_permission_fault(unsigned int esr, struct pt_regs *regs) -{ - unsigned int ec = ESR_ELx_EC(esr); - unsigned int fsc_type = esr & ESR_ELx_FSC_TYPE; - - if (ec != ESR_ELx_EC_DABT_CUR && ec != ESR_ELx_EC_IABT_CUR) - return false; - - if (system_uses_ttbr0_pan()) - return fsc_type == ESR_ELx_FSC_FAULT && - (regs->pstate & PSR_PAN_BIT); - else - return fsc_type == ESR_ELx_FSC_PERM; -} - static bool is_el0_instruction_abort(unsigned int esr) { return ESR_ELx_EC(esr) == ESR_ELx_EC_IABT_LOW; @@ -339,7 +356,7 @@ static int __kprobes do_page_fault(unsigned long addr, unsigned int esr, mm_flags |= FAULT_FLAG_WRITE; } - if (addr < USER_DS && is_permission_fault(esr, regs)) { + if (addr < USER_DS && is_permission_fault(esr, regs, addr)) { /* regs->orig_addr_limit may be 0 if we entered from EL0 */ if (regs->orig_addr_limit == KERNEL_DS) die("Accessing user space memory with fs=KERNEL_DS", regs, esr); diff --git a/arch/arm64/mm/flush.c b/arch/arm64/mm/flush.c index 554a2558c12e..21a8d828cbf4 100644 --- a/arch/arm64/mm/flush.c +++ b/arch/arm64/mm/flush.c @@ -22,7 +22,7 @@ #include <linux/pagemap.h> #include <asm/cacheflush.h> -#include <asm/cachetype.h> +#include <asm/cache.h> #include <asm/tlbflush.h> void sync_icache_aliases(void *kaddr, unsigned long len) @@ -65,8 +65,6 @@ void __sync_icache_dcache(pte_t pte, unsigned long addr) if (!test_and_set_bit(PG_dcache_clean, &page->flags)) sync_icache_aliases(page_address(page), PAGE_SIZE << compound_order(page)); - else if (icache_is_aivivt()) - __flush_icache_all(); } /* diff --git a/arch/arm64/mm/init.c b/arch/arm64/mm/init.c index e19e06593e37..5960bef0170d 100644 --- a/arch/arm64/mm/init.c +++ b/arch/arm64/mm/init.c @@ -30,6 +30,7 @@ #include <linux/gfp.h> #include <linux/memblock.h> #include <linux/sort.h> +#include <linux/of.h> #include <linux/of_fdt.h> #include <linux/dma-mapping.h> #include <linux/dma-contiguous.h> @@ -37,6 +38,8 @@ #include <linux/swiotlb.h> #include <linux/vmalloc.h> #include <linux/mm.h> +#include <linux/kexec.h> +#include <linux/crash_dump.h> #include <asm/boot.h> #include <asm/fixmap.h> @@ -77,6 +80,142 @@ static int __init early_initrd(char *p) early_param("initrd", early_initrd); #endif +#ifdef CONFIG_KEXEC_CORE +/* + * reserve_crashkernel() - reserves memory for crash kernel + * + * This function reserves memory area given in "crashkernel=" kernel command + * line parameter. The memory reserved is used by dump capture kernel when + * primary kernel is crashing. + */ +static void __init reserve_crashkernel(void) +{ + unsigned long long crash_base, crash_size; + int ret; + + ret = parse_crashkernel(boot_command_line, memblock_phys_mem_size(), + &crash_size, &crash_base); + /* no crashkernel= or invalid value specified */ + if (ret || !crash_size) + return; + + crash_size = PAGE_ALIGN(crash_size); + + if (crash_base == 0) { + /* Current arm64 boot protocol requires 2MB alignment */ + crash_base = memblock_find_in_range(0, ARCH_LOW_ADDRESS_LIMIT, + crash_size, SZ_2M); + if (crash_base == 0) { + pr_warn("cannot allocate crashkernel (size:0x%llx)\n", + crash_size); + return; + } + } else { + /* User specifies base address explicitly. */ + if (!memblock_is_region_memory(crash_base, crash_size)) { + pr_warn("cannot reserve crashkernel: region is not memory\n"); + return; + } + + if (memblock_is_region_reserved(crash_base, crash_size)) { + pr_warn("cannot reserve crashkernel: region overlaps reserved memory\n"); + return; + } + + if (!IS_ALIGNED(crash_base, SZ_2M)) { + pr_warn("cannot reserve crashkernel: base address is not 2MB aligned\n"); + return; + } + } + memblock_reserve(crash_base, crash_size); + + pr_info("crashkernel reserved: 0x%016llx - 0x%016llx (%lld MB)\n", + crash_base, crash_base + crash_size, crash_size >> 20); + + crashk_res.start = crash_base; + crashk_res.end = crash_base + crash_size - 1; +} + +static void __init kexec_reserve_crashkres_pages(void) +{ +#ifdef CONFIG_HIBERNATION + phys_addr_t addr; + struct page *page; + + if (!crashk_res.end) + return; + + /* + * To reduce the size of hibernation image, all the pages are + * marked as Reserved initially. + */ + for (addr = crashk_res.start; addr < (crashk_res.end + 1); + addr += PAGE_SIZE) { + page = phys_to_page(addr); + SetPageReserved(page); + } +#endif +} +#else +static void __init reserve_crashkernel(void) +{ +} + +static void __init kexec_reserve_crashkres_pages(void) +{ +} +#endif /* CONFIG_KEXEC_CORE */ + +#ifdef CONFIG_CRASH_DUMP +static int __init early_init_dt_scan_elfcorehdr(unsigned long node, + const char *uname, int depth, void *data) +{ + const __be32 *reg; + int len; + + if (depth != 1 || strcmp(uname, "chosen") != 0) + return 0; + + reg = of_get_flat_dt_prop(node, "linux,elfcorehdr", &len); + if (!reg || (len < (dt_root_addr_cells + dt_root_size_cells))) + return 1; + + elfcorehdr_addr = dt_mem_next_cell(dt_root_addr_cells, ®); + elfcorehdr_size = dt_mem_next_cell(dt_root_size_cells, ®); + + return 1; +} + +/* + * reserve_elfcorehdr() - reserves memory for elf core header + * + * This function reserves the memory occupied by an elf core header + * described in the device tree. This region contains all the + * information about primary kernel's core image and is used by a dump + * capture kernel to access the system memory on primary kernel. + */ +static void __init reserve_elfcorehdr(void) +{ + of_scan_flat_dt(early_init_dt_scan_elfcorehdr, NULL); + + if (!elfcorehdr_size) + return; + + if (memblock_is_region_reserved(elfcorehdr_addr, elfcorehdr_size)) { + pr_warn("elfcorehdr is overlapped\n"); + return; + } + + memblock_reserve(elfcorehdr_addr, elfcorehdr_size); + + pr_info("Reserving %lldKB of memory at 0x%llx for elfcorehdr\n", + elfcorehdr_size >> 10, elfcorehdr_addr); +} +#else +static void __init reserve_elfcorehdr(void) +{ +} +#endif /* CONFIG_CRASH_DUMP */ /* * Return the maximum physical address for ZONE_DMA (DMA_BIT_MASK(32)). It * currently assumes that for memory starting above 4G, 32-bit devices will @@ -188,10 +327,45 @@ static int __init early_mem(char *p) } early_param("mem", early_mem); +static int __init early_init_dt_scan_usablemem(unsigned long node, + const char *uname, int depth, void *data) +{ + struct memblock_region *usablemem = data; + const __be32 *reg; + int len; + + if (depth != 1 || strcmp(uname, "chosen") != 0) + return 0; + + reg = of_get_flat_dt_prop(node, "linux,usable-memory-range", &len); + if (!reg || (len < (dt_root_addr_cells + dt_root_size_cells))) + return 1; + + usablemem->base = dt_mem_next_cell(dt_root_addr_cells, ®); + usablemem->size = dt_mem_next_cell(dt_root_size_cells, ®); + + return 1; +} + +static void __init fdt_enforce_memory_region(void) +{ + struct memblock_region reg = { + .size = 0, + }; + + of_scan_flat_dt(early_init_dt_scan_usablemem, ®); + + if (reg.size) + memblock_cap_memory_range(reg.base, reg.size); +} + void __init arm64_memblock_init(void) { const s64 linear_region_size = -(s64)PAGE_OFFSET; + /* Handle linux,usable-memory-range property */ + fdt_enforce_memory_region(); + /* * Ensure that the linear region takes up exactly half of the kernel * virtual address space. This way, we can distinguish a linear address @@ -297,6 +471,11 @@ void __init arm64_memblock_init(void) arm64_dma_phys_limit = max_zone_dma_phys(); else arm64_dma_phys_limit = PHYS_MASK + 1; + + reserve_crashkernel(); + + reserve_elfcorehdr(); + dma_contiguous_reserve(arm64_dma_phys_limit); memblock_allow_resize(); @@ -416,6 +595,8 @@ void __init mem_init(void) /* this will put all unused low memory onto the freelists */ free_all_bootmem(); + kexec_reserve_crashkres_pages(); + mem_init_print_info(NULL); #define MLK(b, t) b, t, ((t) - (b)) >> 10 diff --git a/arch/arm64/mm/mmu.c b/arch/arm64/mm/mmu.c index d28dbcf596b6..0c429ec6fde8 100644 --- a/arch/arm64/mm/mmu.c +++ b/arch/arm64/mm/mmu.c @@ -22,6 +22,8 @@ #include <linux/kernel.h> #include <linux/errno.h> #include <linux/init.h> +#include <linux/ioport.h> +#include <linux/kexec.h> #include <linux/libfdt.h> #include <linux/mman.h> #include <linux/nodemask.h> @@ -43,6 +45,9 @@ #include <asm/mmu_context.h> #include <asm/ptdump.h> +#define NO_BLOCK_MAPPINGS BIT(0) +#define NO_CONT_MAPPINGS BIT(1) + u64 idmap_t0sz = TCR_T0SZ(VA_BITS); u64 kimage_voffset __ro_after_init; @@ -103,33 +108,27 @@ static bool pgattr_change_is_safe(u64 old, u64 new) */ static const pteval_t mask = PTE_PXN | PTE_RDONLY | PTE_WRITE; - return old == 0 || new == 0 || ((old ^ new) & ~mask) == 0; + /* creating or taking down mappings is always safe */ + if (old == 0 || new == 0) + return true; + + /* live contiguous mappings may not be manipulated at all */ + if ((old | new) & PTE_CONT) + return false; + + return ((old ^ new) & ~mask) == 0; } -static void alloc_init_pte(pmd_t *pmd, unsigned long addr, - unsigned long end, unsigned long pfn, - pgprot_t prot, - phys_addr_t (*pgtable_alloc)(void)) +static void init_pte(pmd_t *pmd, unsigned long addr, unsigned long end, + phys_addr_t phys, pgprot_t prot) { pte_t *pte; - BUG_ON(pmd_sect(*pmd)); - if (pmd_none(*pmd)) { - phys_addr_t pte_phys; - BUG_ON(!pgtable_alloc); - pte_phys = pgtable_alloc(); - pte = pte_set_fixmap(pte_phys); - __pmd_populate(pmd, pte_phys, PMD_TYPE_TABLE); - pte_clear_fixmap(); - } - BUG_ON(pmd_bad(*pmd)); - pte = pte_set_fixmap_offset(pmd, addr); do { pte_t old_pte = *pte; - set_pte(pte, pfn_pte(pfn, prot)); - pfn++; + set_pte(pte, pfn_pte(__phys_to_pfn(phys), prot)); /* * After the PTE entry has been populated once, we @@ -137,32 +136,51 @@ static void alloc_init_pte(pmd_t *pmd, unsigned long addr, */ BUG_ON(!pgattr_change_is_safe(pte_val(old_pte), pte_val(*pte))); + phys += PAGE_SIZE; } while (pte++, addr += PAGE_SIZE, addr != end); pte_clear_fixmap(); } -static void alloc_init_pmd(pud_t *pud, unsigned long addr, unsigned long end, - phys_addr_t phys, pgprot_t prot, - phys_addr_t (*pgtable_alloc)(void), - bool page_mappings_only) +static void alloc_init_cont_pte(pmd_t *pmd, unsigned long addr, + unsigned long end, phys_addr_t phys, + pgprot_t prot, + phys_addr_t (*pgtable_alloc)(void), + int flags) { - pmd_t *pmd; unsigned long next; - /* - * Check for initial section mappings in the pgd/pud and remove them. - */ - BUG_ON(pud_sect(*pud)); - if (pud_none(*pud)) { - phys_addr_t pmd_phys; + BUG_ON(pmd_sect(*pmd)); + if (pmd_none(*pmd)) { + phys_addr_t pte_phys; BUG_ON(!pgtable_alloc); - pmd_phys = pgtable_alloc(); - pmd = pmd_set_fixmap(pmd_phys); - __pud_populate(pud, pmd_phys, PUD_TYPE_TABLE); - pmd_clear_fixmap(); + pte_phys = pgtable_alloc(); + __pmd_populate(pmd, pte_phys, PMD_TYPE_TABLE); } - BUG_ON(pud_bad(*pud)); + BUG_ON(pmd_bad(*pmd)); + + do { + pgprot_t __prot = prot; + + next = pte_cont_addr_end(addr, end); + + /* use a contiguous mapping if the range is suitably aligned */ + if ((((addr | next | phys) & ~CONT_PTE_MASK) == 0) && + (flags & NO_CONT_MAPPINGS) == 0) + __prot = __pgprot(pgprot_val(prot) | PTE_CONT); + + init_pte(pmd, addr, next, phys, __prot); + + phys += next - addr; + } while (addr = next, addr != end); +} + +static void init_pmd(pud_t *pud, unsigned long addr, unsigned long end, + phys_addr_t phys, pgprot_t prot, + phys_addr_t (*pgtable_alloc)(void), int flags) +{ + unsigned long next; + pmd_t *pmd; pmd = pmd_set_fixmap_offset(pud, addr); do { @@ -172,7 +190,7 @@ static void alloc_init_pmd(pud_t *pud, unsigned long addr, unsigned long end, /* try section mapping first */ if (((addr | next | phys) & ~SECTION_MASK) == 0 && - !page_mappings_only) { + (flags & NO_BLOCK_MAPPINGS) == 0) { pmd_set_huge(pmd, phys, prot); /* @@ -182,8 +200,8 @@ static void alloc_init_pmd(pud_t *pud, unsigned long addr, unsigned long end, BUG_ON(!pgattr_change_is_safe(pmd_val(old_pmd), pmd_val(*pmd))); } else { - alloc_init_pte(pmd, addr, next, __phys_to_pfn(phys), - prot, pgtable_alloc); + alloc_init_cont_pte(pmd, addr, next, phys, prot, + pgtable_alloc, flags); BUG_ON(pmd_val(old_pmd) != 0 && pmd_val(old_pmd) != pmd_val(*pmd)); @@ -194,6 +212,41 @@ static void alloc_init_pmd(pud_t *pud, unsigned long addr, unsigned long end, pmd_clear_fixmap(); } +static void alloc_init_cont_pmd(pud_t *pud, unsigned long addr, + unsigned long end, phys_addr_t phys, + pgprot_t prot, + phys_addr_t (*pgtable_alloc)(void), int flags) +{ + unsigned long next; + + /* + * Check for initial section mappings in the pgd/pud. + */ + BUG_ON(pud_sect(*pud)); + if (pud_none(*pud)) { + phys_addr_t pmd_phys; + BUG_ON(!pgtable_alloc); + pmd_phys = pgtable_alloc(); + __pud_populate(pud, pmd_phys, PUD_TYPE_TABLE); + } + BUG_ON(pud_bad(*pud)); + + do { + pgprot_t __prot = prot; + + next = pmd_cont_addr_end(addr, end); + + /* use a contiguous mapping if the range is suitably aligned */ + if ((((addr | next | phys) & ~CONT_PMD_MASK) == 0) && + (flags & NO_CONT_MAPPINGS) == 0) + __prot = __pgprot(pgprot_val(prot) | PTE_CONT); + + init_pmd(pud, addr, next, phys, __prot, pgtable_alloc, flags); + + phys += next - addr; + } while (addr = next, addr != end); +} + static inline bool use_1G_block(unsigned long addr, unsigned long next, unsigned long phys) { @@ -209,7 +262,7 @@ static inline bool use_1G_block(unsigned long addr, unsigned long next, static void alloc_init_pud(pgd_t *pgd, unsigned long addr, unsigned long end, phys_addr_t phys, pgprot_t prot, phys_addr_t (*pgtable_alloc)(void), - bool page_mappings_only) + int flags) { pud_t *pud; unsigned long next; @@ -231,7 +284,8 @@ static void alloc_init_pud(pgd_t *pgd, unsigned long addr, unsigned long end, /* * For 4K granule only, attempt to put down a 1GB block */ - if (use_1G_block(addr, next, phys) && !page_mappings_only) { + if (use_1G_block(addr, next, phys) && + (flags & NO_BLOCK_MAPPINGS) == 0) { pud_set_huge(pud, phys, prot); /* @@ -241,8 +295,8 @@ static void alloc_init_pud(pgd_t *pgd, unsigned long addr, unsigned long end, BUG_ON(!pgattr_change_is_safe(pud_val(old_pud), pud_val(*pud))); } else { - alloc_init_pmd(pud, addr, next, phys, prot, - pgtable_alloc, page_mappings_only); + alloc_init_cont_pmd(pud, addr, next, phys, prot, + pgtable_alloc, flags); BUG_ON(pud_val(old_pud) != 0 && pud_val(old_pud) != pud_val(*pud)); @@ -257,7 +311,7 @@ static void __create_pgd_mapping(pgd_t *pgdir, phys_addr_t phys, unsigned long virt, phys_addr_t size, pgprot_t prot, phys_addr_t (*pgtable_alloc)(void), - bool page_mappings_only) + int flags) { unsigned long addr, length, end, next; pgd_t *pgd = pgd_offset_raw(pgdir, virt); @@ -277,7 +331,7 @@ static void __create_pgd_mapping(pgd_t *pgdir, phys_addr_t phys, do { next = pgd_addr_end(addr, end); alloc_init_pud(pgd, addr, next, phys, prot, pgtable_alloc, - page_mappings_only); + flags); phys += next - addr; } while (pgd++, addr = next, addr != end); } @@ -306,82 +360,80 @@ static void __init create_mapping_noalloc(phys_addr_t phys, unsigned long virt, &phys, virt); return; } - __create_pgd_mapping(init_mm.pgd, phys, virt, size, prot, NULL, false); + __create_pgd_mapping(init_mm.pgd, phys, virt, size, prot, NULL, + NO_CONT_MAPPINGS); } void __init create_pgd_mapping(struct mm_struct *mm, phys_addr_t phys, unsigned long virt, phys_addr_t size, pgprot_t prot, bool page_mappings_only) { + int flags = 0; + BUG_ON(mm == &init_mm); + if (page_mappings_only) + flags = NO_BLOCK_MAPPINGS | NO_CONT_MAPPINGS; + __create_pgd_mapping(mm->pgd, phys, virt, size, prot, - pgd_pgtable_alloc, page_mappings_only); + pgd_pgtable_alloc, flags); } -static void create_mapping_late(phys_addr_t phys, unsigned long virt, - phys_addr_t size, pgprot_t prot) +static void update_mapping_prot(phys_addr_t phys, unsigned long virt, + phys_addr_t size, pgprot_t prot) { if (virt < VMALLOC_START) { - pr_warn("BUG: not creating mapping for %pa at 0x%016lx - outside kernel range\n", + pr_warn("BUG: not updating mapping for %pa at 0x%016lx - outside kernel range\n", &phys, virt); return; } - __create_pgd_mapping(init_mm.pgd, phys, virt, size, prot, - NULL, debug_pagealloc_enabled()); + __create_pgd_mapping(init_mm.pgd, phys, virt, size, prot, NULL, + NO_CONT_MAPPINGS); + + /* flush the TLBs after updating live kernel mappings */ + flush_tlb_kernel_range(virt, virt + size); } -static void __init __map_memblock(pgd_t *pgd, phys_addr_t start, phys_addr_t end) +static void __init __map_memblock(pgd_t *pgd, phys_addr_t start, + phys_addr_t end, pgprot_t prot, int flags) { - phys_addr_t kernel_start = __pa_symbol(_text); - phys_addr_t kernel_end = __pa_symbol(__init_begin); - - /* - * Take care not to create a writable alias for the - * read-only text and rodata sections of the kernel image. - */ - - /* No overlap with the kernel text/rodata */ - if (end < kernel_start || start >= kernel_end) { - __create_pgd_mapping(pgd, start, __phys_to_virt(start), - end - start, PAGE_KERNEL, - early_pgtable_alloc, - debug_pagealloc_enabled()); - return; - } - - /* - * This block overlaps the kernel text/rodata mappings. - * Map the portion(s) which don't overlap. - */ - if (start < kernel_start) - __create_pgd_mapping(pgd, start, - __phys_to_virt(start), - kernel_start - start, PAGE_KERNEL, - early_pgtable_alloc, - debug_pagealloc_enabled()); - if (kernel_end < end) - __create_pgd_mapping(pgd, kernel_end, - __phys_to_virt(kernel_end), - end - kernel_end, PAGE_KERNEL, - early_pgtable_alloc, - debug_pagealloc_enabled()); + __create_pgd_mapping(pgd, start, __phys_to_virt(start), end - start, + prot, early_pgtable_alloc, flags); +} +void __init mark_linear_text_alias_ro(void) +{ /* - * Map the linear alias of the [_text, __init_begin) interval as - * read-only/non-executable. This makes the contents of the - * region accessible to subsystems such as hibernate, but - * protects it from inadvertent modification or execution. + * Remove the write permissions from the linear alias of .text/.rodata */ - __create_pgd_mapping(pgd, kernel_start, __phys_to_virt(kernel_start), - kernel_end - kernel_start, PAGE_KERNEL_RO, - early_pgtable_alloc, debug_pagealloc_enabled()); + update_mapping_prot(__pa_symbol(_text), (unsigned long)lm_alias(_text), + (unsigned long)__init_begin - (unsigned long)_text, + PAGE_KERNEL_RO); } static void __init map_mem(pgd_t *pgd) { + phys_addr_t kernel_start = __pa_symbol(_text); + phys_addr_t kernel_end = __pa_symbol(__init_begin); struct memblock_region *reg; + int flags = 0; + + if (debug_pagealloc_enabled()) + flags = NO_BLOCK_MAPPINGS | NO_CONT_MAPPINGS; + + /* + * Take care not to create a writable alias for the + * read-only text and rodata sections of the kernel image. + * So temporarily mark them as NOMAP to skip mappings in + * the following for-loop + */ + memblock_mark_nomap(kernel_start, kernel_end - kernel_start); +#ifdef CONFIG_KEXEC_CORE + if (crashk_res.end) + memblock_mark_nomap(crashk_res.start, + resource_size(&crashk_res)); +#endif /* map all the memory banks */ for_each_memblock(memory, reg) { @@ -393,33 +445,57 @@ static void __init map_mem(pgd_t *pgd) if (memblock_is_nomap(reg)) continue; - __map_memblock(pgd, start, end); + __map_memblock(pgd, start, end, PAGE_KERNEL, flags); + } + + /* + * Map the linear alias of the [_text, __init_begin) interval + * as non-executable now, and remove the write permission in + * mark_linear_text_alias_ro() below (which will be called after + * alternative patching has completed). This makes the contents + * of the region accessible to subsystems such as hibernate, + * but protects it from inadvertent modification or execution. + * Note that contiguous mappings cannot be remapped in this way, + * so we should avoid them here. + */ + __map_memblock(pgd, kernel_start, kernel_end, + PAGE_KERNEL, NO_CONT_MAPPINGS); + memblock_clear_nomap(kernel_start, kernel_end - kernel_start); + +#ifdef CONFIG_KEXEC_CORE + /* + * Use page-level mappings here so that we can shrink the region + * in page granularity and put back unused memory to buddy system + * through /sys/kernel/kexec_crash_size interface. + */ + if (crashk_res.end) { + __map_memblock(pgd, crashk_res.start, crashk_res.end + 1, + PAGE_KERNEL, + NO_BLOCK_MAPPINGS | NO_CONT_MAPPINGS); + memblock_clear_nomap(crashk_res.start, + resource_size(&crashk_res)); } +#endif } void mark_rodata_ro(void) { unsigned long section_size; - section_size = (unsigned long)_etext - (unsigned long)_text; - create_mapping_late(__pa_symbol(_text), (unsigned long)_text, - section_size, PAGE_KERNEL_ROX); /* * mark .rodata as read only. Use __init_begin rather than __end_rodata * to cover NOTES and EXCEPTION_TABLE. */ section_size = (unsigned long)__init_begin - (unsigned long)__start_rodata; - create_mapping_late(__pa_symbol(__start_rodata), (unsigned long)__start_rodata, + update_mapping_prot(__pa_symbol(__start_rodata), (unsigned long)__start_rodata, section_size, PAGE_KERNEL_RO); - /* flush the TLBs after updating live kernel mappings */ - flush_tlb_all(); - debug_checkwx(); } static void __init map_kernel_segment(pgd_t *pgd, void *va_start, void *va_end, - pgprot_t prot, struct vm_struct *vma) + pgprot_t prot, struct vm_struct *vma, + int flags) { phys_addr_t pa_start = __pa_symbol(va_start); unsigned long size = va_end - va_start; @@ -428,7 +504,7 @@ static void __init map_kernel_segment(pgd_t *pgd, void *va_start, void *va_end, BUG_ON(!PAGE_ALIGNED(size)); __create_pgd_mapping(pgd, pa_start, (unsigned long)va_start, size, prot, - early_pgtable_alloc, debug_pagealloc_enabled()); + early_pgtable_alloc, flags); vma->addr = va_start; vma->phys_addr = pa_start; @@ -439,18 +515,39 @@ static void __init map_kernel_segment(pgd_t *pgd, void *va_start, void *va_end, vm_area_add_early(vma); } +static int __init parse_rodata(char *arg) +{ + return strtobool(arg, &rodata_enabled); +} +early_param("rodata", parse_rodata); + /* * Create fine-grained mappings for the kernel. */ static void __init map_kernel(pgd_t *pgd) { - static struct vm_struct vmlinux_text, vmlinux_rodata, vmlinux_init, vmlinux_data; + static struct vm_struct vmlinux_text, vmlinux_rodata, vmlinux_inittext, + vmlinux_initdata, vmlinux_data; - map_kernel_segment(pgd, _text, _etext, PAGE_KERNEL_EXEC, &vmlinux_text); - map_kernel_segment(pgd, __start_rodata, __init_begin, PAGE_KERNEL, &vmlinux_rodata); - map_kernel_segment(pgd, __init_begin, __init_end, PAGE_KERNEL_EXEC, - &vmlinux_init); - map_kernel_segment(pgd, _data, _end, PAGE_KERNEL, &vmlinux_data); + /* + * External debuggers may need to write directly to the text + * mapping to install SW breakpoints. Allow this (only) when + * explicitly requested with rodata=off. + */ + pgprot_t text_prot = rodata_enabled ? PAGE_KERNEL_ROX : PAGE_KERNEL_EXEC; + + /* + * Only rodata will be remapped with different permissions later on, + * all other segments are allowed to use contiguous mappings. + */ + map_kernel_segment(pgd, _text, _etext, text_prot, &vmlinux_text, 0); + map_kernel_segment(pgd, __start_rodata, __inittext_begin, PAGE_KERNEL, + &vmlinux_rodata, NO_CONT_MAPPINGS); + map_kernel_segment(pgd, __inittext_begin, __inittext_end, text_prot, + &vmlinux_inittext, 0); + map_kernel_segment(pgd, __initdata_begin, __initdata_end, PAGE_KERNEL, + &vmlinux_initdata, 0); + map_kernel_segment(pgd, _data, _end, PAGE_KERNEL, &vmlinux_data, 0); if (!pgd_val(*pgd_offset_raw(pgd, FIXADDR_START))) { /* diff --git a/arch/arm64/mm/pageattr.c b/arch/arm64/mm/pageattr.c index 8def55e7249b..a682a0a2a0fa 100644 --- a/arch/arm64/mm/pageattr.c +++ b/arch/arm64/mm/pageattr.c @@ -17,6 +17,7 @@ #include <linux/vmalloc.h> #include <asm/pgtable.h> +#include <asm/set_memory.h> #include <asm/tlbflush.h> struct page_change_data { @@ -125,20 +126,23 @@ int set_memory_x(unsigned long addr, int numpages) } EXPORT_SYMBOL_GPL(set_memory_x); -#ifdef CONFIG_DEBUG_PAGEALLOC -void __kernel_map_pages(struct page *page, int numpages, int enable) +int set_memory_valid(unsigned long addr, int numpages, int enable) { - unsigned long addr = (unsigned long) page_address(page); - if (enable) - __change_memory_common(addr, PAGE_SIZE * numpages, + return __change_memory_common(addr, PAGE_SIZE * numpages, __pgprot(PTE_VALID), __pgprot(0)); else - __change_memory_common(addr, PAGE_SIZE * numpages, + return __change_memory_common(addr, PAGE_SIZE * numpages, __pgprot(0), __pgprot(PTE_VALID)); } + +#ifdef CONFIG_DEBUG_PAGEALLOC +void __kernel_map_pages(struct page *page, int numpages, int enable) +{ + set_memory_valid((unsigned long)page_address(page), numpages, enable); +} #ifdef CONFIG_HIBERNATION /* * When built with CONFIG_DEBUG_PAGEALLOC and CONFIG_HIBERNATION, this function diff --git a/arch/arm64/net/bpf_jit.h b/arch/arm64/net/bpf_jit.h index 7c16e547ccb2..b02a9268dfbf 100644 --- a/arch/arm64/net/bpf_jit.h +++ b/arch/arm64/net/bpf_jit.h @@ -83,6 +83,25 @@ /* Rt = Rn[0]; Rt2 = Rn[8]; Rn += 16; */ #define A64_POP(Rt, Rt2, Rn) A64_LS_PAIR(Rt, Rt2, Rn, 16, LOAD, POST_INDEX) +/* Load/store exclusive */ +#define A64_SIZE(sf) \ + ((sf) ? AARCH64_INSN_SIZE_64 : AARCH64_INSN_SIZE_32) +#define A64_LSX(sf, Rt, Rn, Rs, type) \ + aarch64_insn_gen_load_store_ex(Rt, Rn, Rs, A64_SIZE(sf), \ + AARCH64_INSN_LDST_##type) +/* Rt = [Rn]; (atomic) */ +#define A64_LDXR(sf, Rt, Rn) \ + A64_LSX(sf, Rt, Rn, A64_ZR, LOAD_EX) +/* [Rn] = Rt; (atomic) Rs = [state] */ +#define A64_STXR(sf, Rt, Rn, Rs) \ + A64_LSX(sf, Rt, Rn, Rs, STORE_EX) + +/* Prefetch */ +#define A64_PRFM(Rn, type, target, policy) \ + aarch64_insn_gen_prefetch(Rn, AARCH64_INSN_PRFM_TYPE_##type, \ + AARCH64_INSN_PRFM_TARGET_##target, \ + AARCH64_INSN_PRFM_POLICY_##policy) + /* Add/subtract (immediate) */ #define A64_ADDSUB_IMM(sf, Rd, Rn, imm12, type) \ aarch64_insn_gen_add_sub_imm(Rd, Rn, imm12, \ diff --git a/arch/arm64/net/bpf_jit_comp.c b/arch/arm64/net/bpf_jit_comp.c index a785554916c0..c6e53580aefe 100644 --- a/arch/arm64/net/bpf_jit_comp.c +++ b/arch/arm64/net/bpf_jit_comp.c @@ -27,6 +27,7 @@ #include <asm/byteorder.h> #include <asm/cacheflush.h> #include <asm/debug-monitors.h> +#include <asm/set_memory.h> #include "bpf_jit.h" @@ -321,6 +322,7 @@ static int build_insn(const struct bpf_insn *insn, struct jit_ctx *ctx) const s32 imm = insn->imm; const int i = insn - ctx->prog->insnsi; const bool is64 = BPF_CLASS(code) == BPF_ALU64; + const bool isdw = BPF_SIZE(code) == BPF_DW; u8 jmp_cond; s32 jmp_offset; @@ -604,15 +606,6 @@ emit_cond_jmp: const struct bpf_insn insn1 = insn[1]; u64 imm64; - if (insn1.code != 0 || insn1.src_reg != 0 || - insn1.dst_reg != 0 || insn1.off != 0) { - /* Note: verifier in BPF core must catch invalid - * instructions. - */ - pr_err_once("Invalid BPF_LD_IMM64 instruction\n"); - return -EINVAL; - } - imm64 = (u64)insn1.imm << 32 | (u32)imm; emit_a64_mov_i64(dst, imm64, ctx); @@ -690,7 +683,16 @@ emit_cond_jmp: case BPF_STX | BPF_XADD | BPF_W: /* STX XADD: lock *(u64 *)(dst + off) += src */ case BPF_STX | BPF_XADD | BPF_DW: - goto notyet; + emit_a64_mov_i(1, tmp, off, ctx); + emit(A64_ADD(1, tmp, tmp, dst), ctx); + emit(A64_PRFM(tmp, PST, L1, STRM), ctx); + emit(A64_LDXR(isdw, tmp2, tmp), ctx); + emit(A64_ADD(isdw, tmp2, tmp2, src), ctx); + emit(A64_STXR(isdw, tmp2, tmp, tmp2), ctx); + jmp_offset = -3; + check_imm19(jmp_offset); + emit(A64_CBNZ(0, tmp2, jmp_offset), ctx); + break; /* R0 = ntohx(*(size *)(((struct sk_buff *)R6)->data + imm)) */ case BPF_LD | BPF_ABS | BPF_W: @@ -757,10 +759,6 @@ emit_cond_jmp: } break; } -notyet: - pr_info_once("*** NOT YET: opcode %02x ***\n", code); - return -EFAULT; - default: pr_err_once("unknown opcode %02x\n", code); return -EINVAL; @@ -779,14 +777,14 @@ static int build_body(struct jit_ctx *ctx) int ret; ret = build_insn(insn, ctx); - - if (ctx->image == NULL) - ctx->offset[i] = ctx->idx; - if (ret > 0) { i++; + if (ctx->image == NULL) + ctx->offset[i] = ctx->idx; continue; } + if (ctx->image == NULL) + ctx->offset[i] = ctx->idx; if (ret) return ret; } |