diff options
Diffstat (limited to 'arch/cris/arch-v10/drivers/Kconfig')
| -rw-r--r-- | arch/cris/arch-v10/drivers/Kconfig | 70 |
1 files changed, 0 insertions, 70 deletions
diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig index daf5f19b61a1..239dab0b95c1 100644 --- a/arch/cris/arch-v10/drivers/Kconfig +++ b/arch/cris/arch-v10/drivers/Kconfig @@ -417,16 +417,6 @@ config ETRAX_USB_HOST for CTRL and BULK traffic only, INTR traffic may work as well however (depending on the requirements of timeliness). -config ETRAX_USB_HOST_PORT1 - bool "USB port 1 enabled" - depends on ETRAX_USB_HOST - default n - -config ETRAX_USB_HOST_PORT2 - bool "USB port 2 enabled" - depends on ETRAX_USB_HOST - default n - config ETRAX_PTABLE_SECTOR int "Byte-offset of partition table sector" depends on ETRAX_AXISFLASHMAP @@ -527,19 +517,6 @@ config ETRAX_GPIO Remember that you need to setup the port directions appropriately in the General configuration. -config ETRAX_PA_BUTTON_BITMASK - hex "PA-buttons bitmask" - depends on ETRAX_GPIO - default "02" - help - This is a bitmask with information about what bits on PA that - are used for buttons. - Most products has a so called TEST button on PA1, if that's true - use 02 here. - Use 00 if there are no buttons on PA. - If the bitmask is <> 00 a button driver will be included in the gpio - driver. ETRAX general I/O support must be enabled. - config ETRAX_PA_CHANGEABLE_DIR hex "PA user changeable dir mask" depends on ETRAX_GPIO @@ -580,51 +557,4 @@ config ETRAX_PB_CHANGEABLE_BITS Bit set = changeable. You probably want 00 here. -config ETRAX_DS1302_RST_ON_GENERIC_PORT - bool "DS1302 RST on Generic Port" - depends on ETRAX_DS1302 - help - If your product has the RST signal line for the DS1302 RTC on the - Generic Port then say Y here, otherwise leave it as N in which - case the RST signal line is assumed to be connected to Port PB - (just like the SCL and SDA lines). - -config ETRAX_DS1302_RSTBIT - int "DS1302 RST bit number" - depends on ETRAX_DS1302 - default "2" - help - This is the bit number for the RST signal line of the DS1302 RTC on - the selected port. If you have selected the generic port then it - should be bit 27, otherwise your best bet is bit 5. - -config ETRAX_DS1302_SCLBIT - int "DS1302 SCL bit number" - depends on ETRAX_DS1302 - default "1" - help - This is the bit number for the SCL signal line of the DS1302 RTC on - Port PB. This is probably best left at 3. - -config ETRAX_DS1302_SDABIT - int "DS1302 SDA bit number" - depends on ETRAX_DS1302 - default "0" - help - This is the bit number for the SDA signal line of the DS1302 RTC on - Port PB. This is probably best left at 2. - -config ETRAX_DS1302_TRICKLE_CHARGE - int "DS1302 Trickle charger value" - depends on ETRAX_DS1302 - default "0" - help - This controls the initial value of the trickle charge register. - 0 = disabled (use this if you are unsure or have a non rechargeable battery) - Otherwise the following values can be OR:ed together to control the - charge current: - 1 = 2kohm, 2 = 4kohm, 3 = 4kohm - 4 = 1 diode, 8 = 2 diodes - Allowed values are (increasing current): 0, 11, 10, 9, 7, 6, 5 - endif |