1 files changed, 0 insertions, 142 deletions
diff --git a/arch/cris/boot/rescue/kimagerescue.S b/arch/cris/boot/rescue/kimagerescue.S
deleted file mode 100644
index 3306098dee15..000000000000
--- a/arch/cris/boot/rescue/kimagerescue.S
+++ /dev/null
@@ -1,142 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Rescue code to be prepended on a kimage and copied to the
- * rescue serial port.
- * This is called from the rescue code, it will copy received data to
- * 4004000 and after a timeout jump to it.
- */
-
-#define ASSEMBLER_MACROS_ONLY
-#include <arch/sv_addr_ag.h>
-
-#define CODE_START 0x40004000
-#define CODE_LENGTH 784
-#define TIMEOUT_VALUE 1000
-
-
-#ifdef CONFIG_ETRAX_RESCUE_SER0
-#define SERXOFF R_SERIAL0_XOFF
-#define SERBAUD R_SERIAL0_BAUD
-#define SERRECC R_SERIAL0_REC_CTRL
-#define SERRDAT R_SERIAL0_REC_DATA
-#define SERSTAT R_SERIAL0_STATUS
-#endif
-#ifdef CONFIG_ETRAX_RESCUE_SER1
-#define SERXOFF R_SERIAL1_XOFF
-#define SERBAUD R_SERIAL1_BAUD
-#define SERRECC R_SERIAL1_REC_CTRL
-#define SERRDAT R_SERIAL1_REC_DATA
-#define SERSTAT R_SERIAL1_STATUS
-#endif
-#ifdef CONFIG_ETRAX_RESCUE_SER2
-#define SERXOFF R_SERIAL2_XOFF
-#define SERBAUD R_SERIAL2_BAUD
-#define SERRECC R_SERIAL2_REC_CTRL
-#define SERRDAT R_SERIAL2_REC_DATA
-#define SERSTAT R_SERIAL2_STATUS
-#endif
-#ifdef CONFIG_ETRAX_RESCUE_SER3
-#define SERXOFF R_SERIAL3_XOFF
-#define SERBAUD R_SERIAL3_BAUD
-#define SERRECC R_SERIAL3_REC_CTRL
-#define SERRDAT R_SERIAL3_REC_DATA
-#define SERSTAT R_SERIAL3_STATUS
-#endif
-
-	.text
-	;; This is the entry point of the rescue code
-	;; 0x80000000 if loaded in flash (as it should be)
-	;; since etrax actually starts at address 2 when booting from flash, we
-	;; put a nop (2 bytes) here first so we dont accidentally skip the di
-
-	nop
-	di
-	;; setup port PA and PB default initial directions and data
-	;; (so we can flash LEDs, and so that DTR and others are set)
-
-	move.b	CONFIG_ETRAX_DEF_R_PORT_PA_DIR, $r0
-	move.b	$r0, [R_PORT_PA_DIR]
-	move.b	CONFIG_ETRAX_DEF_R_PORT_PA_DATA, $r0
-	move.b	$r0, [R_PORT_PA_DATA]
-
-	move.b	CONFIG_ETRAX_DEF_R_PORT_PB_DIR, $r0
-	move.b	$r0, [R_PORT_PB_DIR]
-	move.b	CONFIG_ETRAX_DEF_R_PORT_PB_DATA, $r0
-	move.b	$r0, [R_PORT_PB_DATA]
-
-	;; We need to setup the bus registers before we start using the DRAM
-#include "../../lib/dram_init.S"
-
-	;; Setup the stack to a suitably high address.
-	;; We assume 8 MB is the minimum DRAM in an eLinux
-	;; product and put the sp at the top for now.
-
-	move.d	0x40800000, $sp
-
-	;; setup the serial port at 115200 baud
-
-	moveq	0, $r0
-	move.d	$r0, [SERXOFF]
-
-	move.b	0x99, $r0
-	move.b	$r0, [SERBAUD]		; 115.2kbaud for both transmit
-					; and receive
-
-	move.b	0x40, $r0		; rec enable
-	move.b	$r0, [SERRECC]
-
-
-	moveq	0, $r1			; "timer" to clock out a LED red flash
-	move.d	CODE_START, $r3		; destination counter
-	move.d	CODE_LENGTH, $r4	; length
-	move.d	TIMEOUT_VALUE, $r5	; "timeout" until jump
-
-wait_ser:
-	addq	1, $r1
-	subq	1, $r5			; decrease timeout
-	beq	jump_start		; timed out
-	nop
-#ifndef CONFIG_ETRAX_NO_LEDS
-#ifdef CONFIG_ETRAX_PA_LEDS
-	move.b	CONFIG_ETRAX_DEF_R_PORT_PA_DATA, $r2
-#endif
-#ifdef CONFIG_ETRAX_PB_LEDS
-	move.b	CONFIG_ETRAX_DEF_R_PORT_PB_DATA, $r2
-#endif
-	move.d	(1 << CONFIG_ETRAX_LED1R) | (1 << CONFIG_ETRAX_LED2R), $r0
-	btstq	16, $r1
-	bpl	1f
-	nop
-	or.d	$r0, $r2		; set bit
-	ba	2f
-	nop
-1:	not	$r0			; clear bit
-	and.d	$r0, $r2
-2:
-#ifdef CONFIG_ETRAX_PA_LEDS
-	move.b	$r2, [R_PORT_PA_DATA]
-#endif
-#ifdef CONFIG_ETRAX_PB_LEDS
-	move.b	$r2, [R_PORT_PB_DATA]
-#endif
-#endif
-
-	;; check if we got something on the serial port
-
-	move.b	[SERSTAT], $r0
-	btstq	0, $r0			; data_avail
-	bpl	wait_ser
-	nop
-
-	;; got something - copy the byte and loop
-
-	move.b	[SERRDAT], $r0
-	move.b	$r0, [$r3+]
-	move.d	TIMEOUT_VALUE, $r5	; reset "timeout"
-	subq	1, $r4			; decrease length
-	bne	wait_ser
-	nop
-jump_start:
-	;; jump into downloaded code
-
-	jump	CODE_START