1 files changed, 2 insertions, 84 deletions

diff --git a/arch/x86/kernel/i8253.c b/arch/x86/kernel/i8253.c
index 2dfd31597443..fb66dc9e36cb 100644
--- a/arch/x86/kernel/i8253.c
+++ b/arch/x86/kernel/i8253.c
@@ -93,7 +93,6 @@ static struct clock_event_device pit_ce = {
 	.features	= CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
 	.set_mode	= init_pit_timer,
 	.set_next_event = pit_next_event,
-	.shift		= 32,
 	.irq		= 0,
 };
 
@@ -108,90 +107,12 @@ void __init setup_pit_timer(void)
 	 * IO_APIC has been initialized.
 	 */
 	pit_ce.cpumask = cpumask_of(smp_processor_id());
-	pit_ce.mult = div_sc(CLOCK_TICK_RATE, NSEC_PER_SEC, pit_ce.shift);
-	pit_ce.max_delta_ns = clockevent_delta2ns(0x7FFF, &pit_ce);
-	pit_ce.min_delta_ns = clockevent_delta2ns(0xF, &pit_ce);
 
-	clockevents_register_device(&pit_ce);
+	clockevents_config_and_register(&pit_ce, CLOCK_TICK_RATE, 0xF, 0x7FFF);
 	global_clock_event = &pit_ce;
 }
 
 #ifndef CONFIG_X86_64
-/*
- * Since the PIT overflows every tick, its not very useful
- * to just read by itself. So use jiffies to emulate a free
- * running counter:
- */
-static cycle_t pit_read(struct clocksource *cs)
-{
-	static int old_count;
-	static u32 old_jifs;
-	unsigned long flags;
-	int count;
-	u32 jifs;
-
-	raw_spin_lock_irqsave(&i8253_lock, flags);
-	/*
-	 * Although our caller may have the read side of xtime_lock,
-	 * this is now a seqlock, and we are cheating in this routine
-	 * by having side effects on state that we cannot undo if
-	 * there is a collision on the seqlock and our caller has to
-	 * retry.  (Namely, old_jifs and old_count.)  So we must treat
-	 * jiffies as volatile despite the lock.  We read jiffies
-	 * before latching the timer count to guarantee that although
-	 * the jiffies value might be older than the count (that is,
-	 * the counter may underflow between the last point where
-	 * jiffies was incremented and the point where we latch the
-	 * count), it cannot be newer.
-	 */
-	jifs = jiffies;
-	outb_pit(0x00, PIT_MODE);	/* latch the count ASAP */
-	count = inb_pit(PIT_CH0);	/* read the latched count */
-	count |= inb_pit(PIT_CH0) << 8;
-
-	/* VIA686a test code... reset the latch if count > max + 1 */
-	if (count > LATCH) {
-		outb_pit(0x34, PIT_MODE);
-		outb_pit(LATCH & 0xff, PIT_CH0);
-		outb_pit(LATCH >> 8, PIT_CH0);
-		count = LATCH - 1;
-	}
-
-	/*
-	 * It's possible for count to appear to go the wrong way for a
-	 * couple of reasons:
-	 *
-	 *  1. The timer counter underflows, but we haven't handled the
-	 *     resulting interrupt and incremented jiffies yet.
-	 *  2. Hardware problem with the timer, not giving us continuous time,
-	 *     the counter does small "jumps" upwards on some Pentium systems,
-	 *     (see c't 95/10 page 335 for Neptun bug.)
-	 *
-	 * Previous attempts to handle these cases intelligently were
-	 * buggy, so we just do the simple thing now.
-	 */
-	if (count > old_count && jifs == old_jifs)
-		count = old_count;
-
-	old_count = count;
-	old_jifs = jifs;
-
-	raw_spin_unlock_irqrestore(&i8253_lock, flags);
-
-	count = (LATCH - 1) - count;
-
-	return (cycle_t)(jifs * LATCH) + count;
-}
-
-static struct clocksource pit_cs = {
-	.name		= "pit",
-	.rating		= 110,
-	.read		= pit_read,
-	.mask		= CLOCKSOURCE_MASK(32),
-	.mult		= 0,
-	.shift		= 20,
-};
-
 static int __init init_pit_clocksource(void)
 {
 	 /*
@@ -205,10 +126,7 @@ static int __init init_pit_clocksource(void)
 	    pit_ce.mode != CLOCK_EVT_MODE_PERIODIC)
 		return 0;
 
-	pit_cs.mult = clocksource_hz2mult(CLOCK_TICK_RATE, pit_cs.shift);
-
-	return clocksource_register(&pit_cs);
+	return clocksource_i8253_init();
 }
 arch_initcall(init_pit_clocksource);
-
 #endif /* !CONFIG_X86_64 */