diff options
Diffstat (limited to 'drivers/media/radio/Kconfig')
| -rw-r--r-- | drivers/media/radio/Kconfig | 348 |
1 files changed, 168 insertions, 180 deletions
diff --git a/drivers/media/radio/Kconfig b/drivers/media/radio/Kconfig index d29e29645e04..cca03bd2cc42 100644 --- a/drivers/media/radio/Kconfig +++ b/drivers/media/radio/Kconfig @@ -5,69 +5,17 @@ menuconfig RADIO_ADAPTERS bool "Radio Adapters" - depends on VIDEO_V4L2 + depends on VIDEO_DEV depends on MEDIA_RADIO_SUPPORT default y help Say Y here to enable selecting AM/FM radio adapters. -if RADIO_ADAPTERS && VIDEO_V4L2 - -config RADIO_TEA575X - tristate - -source "drivers/media/radio/si470x/Kconfig" - -config RADIO_SI4713 - tristate "Silicon Labs Si4713 FM Radio with RDS Transmitter support" - depends on VIDEO_V4L2 - -source "drivers/media/radio/si4713/Kconfig" - -config RADIO_SI476X - tristate "Silicon Laboratories Si476x I2C FM Radio" - depends on I2C && VIDEO_V4L2 - depends on MFD_SI476X_CORE - depends on SND_SOC - select SND_SOC_SI476X - help - Choose Y here if you have this FM radio chip. - - In order to control your radio card, you will need to use programs - that are compatible with the Video For Linux 2 API. Information on - this API and pointers to "v4l2" programs may be found at - <file:Documentation/userspace-api/media/index.rst>. - - To compile this driver as a module, choose M here: the - module will be called radio-si476x. - -config USB_MR800 - tristate "AverMedia MR 800 USB FM radio support" - depends on USB && VIDEO_V4L2 - help - Say Y here if you want to connect this type of radio to your - computer's USB port. Note that the audio is not digital, and - you must connect the line out connector to a sound card or a - set of speakers. - - To compile this driver as a module, choose M here: the - module will be called radio-mr800. - -config USB_DSBR - tristate "D-Link/GemTek USB FM radio support" - depends on USB && VIDEO_V4L2 - help - Say Y here if you want to connect this type of radio to your - computer's USB port. Note that the audio is not digital, and - you must connect the line out connector to a sound card or a - set of speakers. - - To compile this driver as a module, choose M here: the - module will be called dsbr100. +if RADIO_ADAPTERS config RADIO_MAXIRADIO tristate "Guillemot MAXI Radio FM 2000 radio" - depends on VIDEO_V4L2 && PCI + depends on PCI select RADIO_TEA575X help Choose Y here if you have this radio card. This card may also be @@ -81,6 +29,18 @@ config RADIO_MAXIRADIO To compile this driver as a module, choose M here: the module will be called radio-maxiradio. +config RADIO_SAA7706H + tristate "SAA7706H Car Radio DSP" + depends on I2C + help + Say Y here if you want to use the SAA7706H Car radio Digital + Signal Processor, found for instance on the Russellville development + board. On the russellville the device is connected to internal + timberdale I2C bus. + + To compile this driver as a module, choose M here: the + module will be called SAA7706H. + config RADIO_SHARK tristate "Griffin radioSHARK USB radio receiver" depends on USB @@ -116,45 +76,32 @@ config RADIO_SHARK2 To compile this driver as a module, choose M here: the module will be called radio-shark2. -config USB_KEENE - tristate "Keene FM Transmitter USB support" - depends on USB && VIDEO_V4L2 - help - Say Y here if you want to connect this type of FM transmitter - to your computer's USB port. - - To compile this driver as a module, choose M here: the - module will be called radio-keene. +config RADIO_SI4713 + tristate "Silicon Labs Si4713 FM Radio with RDS Transmitter support" -config USB_RAREMONO - tristate "Thanko's Raremono AM/FM/SW radio support" - depends on USB && VIDEO_V4L2 +config RADIO_SI476X + tristate "Silicon Laboratories Si476x I2C FM Radio" + depends on I2C + depends on MFD_SI476X_CORE + depends on SND_SOC + select SND_SOC_SI476X help - The 'Thanko's Raremono' device contains the Si4734 chip from Silicon Labs Inc. - It is one of the very few or perhaps the only consumer USB radio device - to receive the AM/FM/SW bands. + Choose Y here if you have this FM radio chip. - Say Y here if you want to connect this type of AM/FM/SW receiver - to your computer's USB port. + In order to control your radio card, you will need to use programs + that are compatible with the Video For Linux 2 API. Information on + this API and pointers to "v4l2" programs may be found at + <file:Documentation/userspace-api/media/index.rst>. To compile this driver as a module, choose M here: the - module will be called radio-raremono. - -config USB_MA901 - tristate "Masterkit MA901 USB FM radio support" - depends on USB && VIDEO_V4L2 - help - Say Y here if you want to connect this type of radio to your - computer's USB port. Note that the audio is not digital, and - you must connect the line out connector to a sound card or a - set of speakers or headphones. + module will be called radio-si476x. - To compile this driver as a module, choose M here: the - module will be called radio-ma901. +config RADIO_TEA575X + tristate config RADIO_TEA5764 tristate "TEA5764 I2C FM radio support" - depends on I2C && VIDEO_V4L2 + depends on I2C help Say Y here if you want to use the TEA5764 FM chip found in EZX phones. This FM chip is present in EZX phones from Motorola, @@ -171,21 +118,9 @@ config RADIO_TEA5764_XTAL Say Y here if TEA5764 have a 32768 Hz crystal in circuit, say N here if TEA5764 reference frequency is connected in FREQIN. -config RADIO_SAA7706H - tristate "SAA7706H Car Radio DSP" - depends on I2C && VIDEO_V4L2 - help - Say Y here if you want to use the SAA7706H Car radio Digital - Signal Processor, found for instance on the Russellville development - board. On the russellville the device is connected to internal - timberdale I2C bus. - - To compile this driver as a module, choose M here: the - module will be called SAA7706H. - config RADIO_TEF6862 tristate "TEF6862 Car Radio Enhanced Selectivity Tuner" - depends on I2C && VIDEO_V4L2 + depends on I2C help Say Y here if you want to use the TEF6862 Car Radio Enhanced Selectivity Tuner, found for instance on the Russellville development @@ -197,7 +132,7 @@ config RADIO_TEF6862 config RADIO_TIMBERDALE tristate "Enable the Timberdale radio driver" - depends on MFD_TIMBERDALE && VIDEO_V4L2 + depends on MFD_TIMBERDALE depends on I2C # for RADIO_SAA7706H select RADIO_TEF6862 select RADIO_SAA7706H @@ -208,7 +143,7 @@ config RADIO_TIMBERDALE config RADIO_WL1273 tristate "Texas Instruments WL1273 I2C FM Radio" - depends on I2C && VIDEO_V4L2 + depends on I2C select MFD_CORE select MFD_WL1273_CORE select FW_LOADER @@ -223,96 +158,88 @@ config RADIO_WL1273 To compile this driver as a module, choose M here: the module will be called radio-wl1273. -# TI's ST based wl128x FM radio -source "drivers/media/radio/wl128x/Kconfig" +config USB_DSBR + tristate "D-Link/GemTek USB FM radio support" + depends on USB + help + Say Y here if you want to connect this type of radio to your + computer's USB port. Note that the audio is not digital, and + you must connect the line out connector to a sound card or a + set of speakers. -# -# ISA drivers configuration -# + To compile this driver as a module, choose M here: the + module will be called dsbr100. -menuconfig V4L_RADIO_ISA_DRIVERS - bool "ISA radio devices" - depends on ISA || COMPILE_TEST +config USB_KEENE + tristate "Keene FM Transmitter USB support" + depends on USB help - Say Y here to enable support for these ISA drivers. - -if V4L_RADIO_ISA_DRIVERS + Say Y here if you want to connect this type of FM transmitter + to your computer's USB port. -config RADIO_ISA - depends on ISA || COMPILE_TEST - tristate + To compile this driver as a module, choose M here: the + module will be called radio-keene. -config RADIO_CADET - tristate "ADS Cadet AM/FM Tuner" - depends on ISA || COMPILE_TEST - depends on VIDEO_V4L2 +config USB_MA901 + tristate "Masterkit MA901 USB FM radio support" + depends on USB help - Choose Y here if you have one of these AM/FM radio cards, and then - fill in the port address below. + Say Y here if you want to connect this type of radio to your + computer's USB port. Note that the audio is not digital, and + you must connect the line out connector to a sound card or a + set of speakers or headphones. To compile this driver as a module, choose M here: the - module will be called radio-cadet. + module will be called radio-ma901. -config RADIO_RTRACK - tristate "AIMSlab RadioTrack (aka RadioReveal) support" - depends on ISA || COMPILE_TEST - depends on VIDEO_V4L2 - select RADIO_ISA +config USB_MR800 + tristate "AverMedia MR 800 USB FM radio support" + depends on USB help - Choose Y here if you have one of these FM radio cards, and then fill - in the port address below. + Say Y here if you want to connect this type of radio to your + computer's USB port. Note that the audio is not digital, and + you must connect the line out connector to a sound card or a + set of speakers. - Note that newer AIMSlab RadioTrack cards have a different chipset - and are not supported by this driver. For these cards, use the - RadioTrack II driver below. + To compile this driver as a module, choose M here: the + module will be called radio-mr800. - If you have a GemTeks combined (PnP) sound- and radio card you must - use this driver as a module and setup the card with isapnptools. - You must also pass the module a suitable io parameter, 0x248 has - been reported to be used by these cards. +config USB_RAREMONO + tristate "Thanko's Raremono AM/FM/SW radio support" + depends on USB + help + The 'Thanko's Raremono' device contains the Si4734 chip from Silicon Labs Inc. + It is one of the very few or perhaps the only consumer USB radio device + to receive the AM/FM/SW bands. - More information is contained in the file - <file:Documentation/driver-api/media/drivers/radiotrack.rst>. + Say Y here if you want to connect this type of AM/FM/SW receiver + to your computer's USB port. To compile this driver as a module, choose M here: the - module will be called radio-aimslab. + module will be called radio-raremono. -config RADIO_RTRACK_PORT - hex "RadioTrack i/o port (0x20f or 0x30f)" - depends on RADIO_RTRACK=y - default "30f" - help - Enter either 0x30f or 0x20f here. The card default is 0x30f, if you - haven't changed the jumper setting on the card. +source "drivers/media/radio/si470x/Kconfig" +source "drivers/media/radio/si4713/Kconfig" -config RADIO_RTRACK2 - tristate "AIMSlab RadioTrack II support" - depends on ISA || COMPILE_TEST - depends on VIDEO_V4L2 - select RADIO_ISA - help - Choose Y here if you have this FM radio card, and then fill in the - port address below. +# TI's ST based wl128x FM radio - Note: this driver hasn't been tested since a long time due to lack - of hardware. If you have this hardware, then please contact the - linux-media mailinglist. +source "drivers/media/radio/wl128x/Kconfig" - To compile this driver as a module, choose M here: the - module will be called radio-rtrack2. +# +# ISA drivers configuration +# -config RADIO_RTRACK2_PORT - hex "RadioTrack II i/o port (0x20c or 0x30c)" - depends on RADIO_RTRACK2=y - default "30c" +menuconfig V4L_RADIO_ISA_DRIVERS + bool "ISA radio devices" + depends on ISA || COMPILE_TEST help - Enter either 0x30c or 0x20c here. The card default is 0x30c, if you - haven't changed the jumper setting on the card. + Say Y here to enable support for these ISA drivers. + +if V4L_RADIO_ISA_DRIVERS config RADIO_AZTECH tristate "Aztech/Packard Bell Radio" depends on ISA || COMPILE_TEST - depends on VIDEO_V4L2 select RADIO_ISA help Choose Y here if you have one of these FM radio cards, and then fill @@ -330,10 +257,19 @@ config RADIO_AZTECH_PORT haven't changed the setting of jumper JP3 on the card. Removing the jumper sets the card to 0x358. +config RADIO_CADET + tristate "ADS Cadet AM/FM Tuner" + depends on ISA || COMPILE_TEST + help + Choose Y here if you have one of these AM/FM radio cards, and then + fill in the port address below. + + To compile this driver as a module, choose M here: the + module will be called radio-cadet. + config RADIO_GEMTEK tristate "GemTek Radio card (or compatible) support" depends on ISA || COMPILE_TEST - depends on VIDEO_V4L2 select RADIO_ISA help Choose Y here if you have this FM radio card, and then fill in the @@ -371,10 +307,14 @@ config RADIO_GEMTEK_PROBE following ports will be probed: 0x20c, 0x30c, 0x24c, 0x34c, 0x248 and 0x28c. +config RADIO_ISA + depends on ISA || COMPILE_TEST + tristate + config RADIO_MIROPCM20 tristate "miroSOUND PCM20 radio" depends on ISA || COMPILE_TEST - depends on ISA_DMA_API && VIDEO_V4L2 && SND + depends on ISA_DMA_API && SND select SND_ISA select SND_MIRO help @@ -386,10 +326,63 @@ config RADIO_MIROPCM20 To compile this driver as a module, choose M here: the module will be called radio-miropcm20. +config RADIO_RTRACK + tristate "AIMSlab RadioTrack (aka RadioReveal) support" + depends on ISA || COMPILE_TEST + select RADIO_ISA + help + Choose Y here if you have one of these FM radio cards, and then fill + in the port address below. + + Note that newer AIMSlab RadioTrack cards have a different chipset + and are not supported by this driver. For these cards, use the + RadioTrack II driver below. + + If you have a GemTeks combined (PnP) sound- and radio card you must + use this driver as a module and setup the card with isapnptools. + You must also pass the module a suitable io parameter, 0x248 has + been reported to be used by these cards. + + More information is contained in the file + <file:Documentation/driver-api/media/drivers/radiotrack.rst>. + + To compile this driver as a module, choose M here: the + module will be called radio-aimslab. + +config RADIO_RTRACK2 + tristate "AIMSlab RadioTrack II support" + depends on ISA || COMPILE_TEST + select RADIO_ISA + help + Choose Y here if you have this FM radio card, and then fill in the + port address below. + + Note: this driver hasn't been tested since a long time due to lack + of hardware. If you have this hardware, then please contact the + linux-media mailinglist. + + To compile this driver as a module, choose M here: the + module will be called radio-rtrack2. + +config RADIO_RTRACK2_PORT + hex "RadioTrack II i/o port (0x20c or 0x30c)" + depends on RADIO_RTRACK2=y + default "30c" + help + Enter either 0x30c or 0x20c here. The card default is 0x30c, if you + haven't changed the jumper setting on the card. + +config RADIO_RTRACK_PORT + hex "RadioTrack i/o port (0x20f or 0x30f)" + depends on RADIO_RTRACK=y + default "30f" + help + Enter either 0x30f or 0x20f here. The card default is 0x30f, if you + haven't changed the jumper setting on the card. + config RADIO_SF16FMI tristate "SF16-FMI/SF16-FMP/SF16-FMD Radio" depends on ISA || COMPILE_TEST - depends on VIDEO_V4L2 help Choose Y here if you have one of these FM radio cards. @@ -399,7 +392,6 @@ config RADIO_SF16FMI config RADIO_SF16FMR2 tristate "SF16-FMR2/SF16-FMD2 Radio" depends on ISA || COMPILE_TEST - depends on VIDEO_V4L2 select RADIO_TEA575X help Choose Y here if you have one of these FM radio cards. @@ -410,7 +402,6 @@ config RADIO_SF16FMR2 config RADIO_TERRATEC tristate "TerraTec ActiveRadio ISA Standalone" depends on ISA || COMPILE_TEST - depends on VIDEO_V4L2 select RADIO_ISA help Choose Y here if you have this FM radio card. @@ -425,7 +416,6 @@ config RADIO_TERRATEC config RADIO_TRUST tristate "Trust FM radio card" depends on ISA || COMPILE_TEST - depends on VIDEO_V4L2 select RADIO_ISA help This is a driver for the Trust FM radio cards. Say Y if you have @@ -449,7 +439,6 @@ config RADIO_TRUST_PORT config RADIO_TYPHOON tristate "Typhoon Radio (a.k.a. EcoRadio)" depends on ISA || COMPILE_TEST - depends on VIDEO_V4L2 select RADIO_ISA help Choose Y here if you have one of these FM radio cards, and then fill @@ -462,13 +451,6 @@ config RADIO_TYPHOON To compile this driver as a module, choose M here: the module will be called radio-typhoon. -config RADIO_TYPHOON_PORT - hex "Typhoon I/O port (0x316 or 0x336)" - depends on RADIO_TYPHOON=y - default "316" - help - Enter the I/O port of your Typhoon or EcoRadio radio card. - config RADIO_TYPHOON_MUTEFREQ int "Typhoon frequency set when muting the device (kHz)" depends on RADIO_TYPHOON=y @@ -481,10 +463,16 @@ config RADIO_TYPHOON_MUTEFREQ the device is muted. There should be no local radio station at that frequency. +config RADIO_TYPHOON_PORT + hex "Typhoon I/O port (0x316 or 0x336)" + depends on RADIO_TYPHOON=y + default "316" + help + Enter the I/O port of your Typhoon or EcoRadio radio card. + config RADIO_ZOLTRIX tristate "Zoltrix Radio" depends on ISA || COMPILE_TEST - depends on VIDEO_V4L2 select RADIO_ISA help Choose Y here if you have one of these FM radio cards, and then fill |