diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/media/video/em28xx/em28xx-cards.c | 50 |
1 files changed, 34 insertions, 16 deletions
diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c index 6b2b5d3e2fad..54429b629b2d 100644 --- a/drivers/media/video/em28xx/em28xx-cards.c +++ b/drivers/media/video/em28xx/em28xx-cards.c @@ -218,7 +218,7 @@ static struct em28xx_reg_seq silvercrest_reg_seq[] = { struct em28xx_board em28xx_boards[] = { [EM2750_BOARD_UNKNOWN] = { .name = "EM2710/EM2750/EM2751 webcam grabber", - .xclk = EM28XX_XCLK_FREQUENCY_48MHZ, + .xclk = EM28XX_XCLK_FREQUENCY_20MHZ, .tuner_type = TUNER_ABSENT, .is_webcam = 1, .input = { { @@ -1768,6 +1768,7 @@ static int em28xx_hint_sensor(struct em28xx *dev) __be16 version_be; u16 version; + /* Micron sensor detection */ dev->i2c_client.addr = 0xba >> 1; cmd = 0; i2c_master_send(&dev->i2c_client, &cmd, 1); @@ -1776,16 +1777,27 @@ static int em28xx_hint_sensor(struct em28xx *dev) return -EINVAL; version = be16_to_cpu(version_be); - switch (version) { case 0x8232: /* mt9v011 640x480 1.3 Mpix sensor */ case 0x8243: /* mt9v011 rev B 640x480 1.3 Mpix sensor */ dev->model = EM2820_BOARD_SILVERCREST_WEBCAM; + em28xx_set_model(dev); + sensor_name = "mt9v011"; dev->em28xx_sensor = EM28XX_MT9V011; dev->sensor_xres = 640; dev->sensor_yres = 480; - dev->sensor_xtal = 12150000; + /* + * FIXME: mt9v011 uses I2S speed as xtal clk - at least with + * the Silvercrest cam I have here for testing - for higher + * resolutions, a high clock cause horizontal artifacts, so we + * need to use a lower xclk frequency. + * Yet, it would be possible to adjust xclk depending on the + * desired resolution, since this affects directly the + * frame rate. + */ + dev->board.xclk = EM28XX_XCLK_FREQUENCY_4_3MHZ; + dev->sensor_xtal = 4300000; /* probably means GRGB 16 bit bayer */ dev->vinmode = 0x0d; @@ -1794,6 +1806,8 @@ static int em28xx_hint_sensor(struct em28xx *dev) break; case 0x8431: dev->model = EM2750_BOARD_UNKNOWN; + em28xx_set_model(dev); + sensor_name = "mt9m001"; dev->em28xx_sensor = EM28XX_MT9M001; em28xx_initialize_mt9m001(dev); @@ -1810,6 +1824,9 @@ static int em28xx_hint_sensor(struct em28xx *dev) return -EINVAL; } + /* Setup webcam defaults */ + em28xx_pre_card_setup(dev); + em28xx_errdev("Sensor is %s, using model %s entry.\n", sensor_name, em28xx_boards[dev->model].name); @@ -2169,7 +2186,20 @@ void em28xx_register_i2c_ir(struct em28xx *dev) void em28xx_card_setup(struct em28xx *dev) { - em28xx_set_model(dev); + /* + * If the device can be a webcam, seek for a sensor. + * If sensor is not found, then it isn't a webcam. + */ + if (dev->board.is_webcam) { + if (em28xx_hint_sensor(dev) < 0) + dev->board.is_webcam = 0; + else + dev->progressive = 1; + } else + em28xx_set_model(dev); + + em28xx_info("Identified as %s (card=%d)\n", + dev->board.name, dev->model); dev->tuner_type = em28xx_boards[dev->model].tuner_type; if (em28xx_boards[dev->model].tuner_addr) @@ -2489,18 +2519,6 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev, dev->vinmode = 0x10; dev->vinctl = 0x11; - /* - * If the device can be a webcam, seek for a sensor. - * If sensor is not found, then it isn't a webcam. - */ - if (dev->board.is_webcam) - if (em28xx_hint_sensor(dev) < 0) - dev->board.is_webcam = 0; - - /* It makes no sense to use de-interlacing mode on webcams */ - if (dev->board.is_webcam) - dev->progressive = 1; - /* Do board specific init and eeprom reading */ em28xx_card_setup(dev); |