diff options
Diffstat (limited to 'drivers/mmc/host/sdhci-xenon-phy.c')
| -rw-r--r-- | drivers/mmc/host/sdhci-xenon-phy.c | 34 |
1 files changed, 28 insertions, 6 deletions
diff --git a/drivers/mmc/host/sdhci-xenon-phy.c b/drivers/mmc/host/sdhci-xenon-phy.c index f7e26b031e76..ec8794335241 100644 --- a/drivers/mmc/host/sdhci-xenon-phy.c +++ b/drivers/mmc/host/sdhci-xenon-phy.c @@ -409,17 +409,30 @@ static int xenon_emmc_phy_config_tuning(struct sdhci_host *host) return 0; } -static void xenon_emmc_phy_disable_data_strobe(struct sdhci_host *host) +static void xenon_emmc_phy_disable_strobe(struct sdhci_host *host) { + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct xenon_priv *priv = sdhci_pltfm_priv(pltfm_host); u32 reg; - /* Disable SDHC Data Strobe */ + /* Disable both SDHC Data Strobe and Enhanced Strobe */ reg = sdhci_readl(host, XENON_SLOT_EMMC_CTRL); - reg &= ~XENON_ENABLE_DATA_STROBE; + reg &= ~(XENON_ENABLE_DATA_STROBE | XENON_ENABLE_RESP_STROBE); sdhci_writel(host, reg, XENON_SLOT_EMMC_CTRL); + + /* Clear Strobe line Pull down or Pull up */ + if (priv->phy_type == EMMC_5_0_PHY) { + reg = sdhci_readl(host, XENON_EMMC_5_0_PHY_PAD_CONTROL); + reg &= ~(XENON_EMMC5_FC_QSP_PD | XENON_EMMC5_FC_QSP_PU); + sdhci_writel(host, reg, XENON_EMMC_5_0_PHY_PAD_CONTROL); + } else { + reg = sdhci_readl(host, XENON_EMMC_PHY_PAD_CONTROL1); + reg &= ~(XENON_EMMC5_1_FC_QSP_PD | XENON_EMMC5_1_FC_QSP_PU); + sdhci_writel(host, reg, XENON_EMMC_PHY_PAD_CONTROL1); + } } -/* Set HS400 Data Strobe */ +/* Set HS400 Data Strobe and Enhanced Strobe */ static void xenon_emmc_phy_strobe_delay_adj(struct sdhci_host *host) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); @@ -439,6 +452,15 @@ static void xenon_emmc_phy_strobe_delay_adj(struct sdhci_host *host) /* Enable SDHC Data Strobe */ reg = sdhci_readl(host, XENON_SLOT_EMMC_CTRL); reg |= XENON_ENABLE_DATA_STROBE; + /* + * Enable SDHC Enhanced Strobe if supported + * Xenon Enhanced Strobe should be enabled only when + * 1. card is in HS400 mode and + * 2. SDCLK is higher than 52MHz + * 3. DLL is enabled + */ + if (host->mmc->ios.enhanced_strobe) + reg |= XENON_ENABLE_RESP_STROBE; sdhci_writel(host, reg, XENON_SLOT_EMMC_CTRL); /* Set Data Strobe Pull down */ @@ -615,7 +637,7 @@ static void xenon_emmc_phy_set(struct sdhci_host *host, sdhci_writel(host, phy_regs->logic_timing_val, phy_regs->logic_timing_adj); else - xenon_emmc_phy_disable_data_strobe(host); + xenon_emmc_phy_disable_strobe(host); phy_init: xenon_emmc_phy_init(host); @@ -705,7 +727,7 @@ void xenon_soc_pad_ctrl(struct sdhci_host *host, /* * Setting PHY when card is working in High Speed Mode. - * HS400 set data strobe line. + * HS400 set Data Strobe and Enhanced Strobe if it is supported. * HS200/SDR104 set tuning config to prepare for tuning. */ static int xenon_hs_delay_adj(struct sdhci_host *host) |