diff options
Diffstat (limited to 'drivers/net/ethernet/davicom')
| -rw-r--r-- | drivers/net/ethernet/davicom/dm9000.c | 56 |
1 files changed, 38 insertions, 18 deletions
diff --git a/drivers/net/ethernet/davicom/dm9000.c b/drivers/net/ethernet/davicom/dm9000.c index be8efeea51f2..7080ad6c4014 100644 --- a/drivers/net/ethernet/davicom/dm9000.c +++ b/drivers/net/ethernet/davicom/dm9000.c @@ -158,18 +158,6 @@ static inline board_info_t *to_dm9000_board(struct net_device *dev) /* DM9000 network board routine ---------------------------- */ -static void -dm9000_reset(board_info_t * db) -{ - dev_dbg(db->dev, "resetting device\n"); - - /* RESET device */ - writeb(DM9000_NCR, db->io_addr); - udelay(200); - writeb(NCR_RST, db->io_data); - udelay(200); -} - /* * Read a byte from I/O port */ @@ -191,6 +179,27 @@ iow(board_info_t * db, int reg, int value) writeb(value, db->io_data); } +static void +dm9000_reset(board_info_t *db) +{ + dev_dbg(db->dev, "resetting device\n"); + + /* Reset DM9000, see DM9000 Application Notes V1.22 Jun 11, 2004 page 29 + * The essential point is that we have to do a double reset, and the + * instruction is to set LBK into MAC internal loopback mode. + */ + iow(db, DM9000_NCR, 0x03); + udelay(100); /* Application note says at least 20 us */ + if (ior(db, DM9000_NCR) & 1) + dev_err(db->dev, "dm9000 did not respond to first reset\n"); + + iow(db, DM9000_NCR, 0); + iow(db, DM9000_NCR, 0x03); + udelay(100); + if (ior(db, DM9000_NCR) & 1) + dev_err(db->dev, "dm9000 did not respond to second reset\n"); +} + /* routines for sending block to chip */ static void dm9000_outblk_8bit(void __iomem *reg, void *data, int count) @@ -744,15 +753,20 @@ static const struct ethtool_ops dm9000_ethtool_ops = { static void dm9000_show_carrier(board_info_t *db, unsigned carrier, unsigned nsr) { + int lpa; struct net_device *ndev = db->ndev; + struct mii_if_info *mii = &db->mii; unsigned ncr = dm9000_read_locked(db, DM9000_NCR); - if (carrier) - dev_info(db->dev, "%s: link up, %dMbps, %s-duplex, no LPA\n", + if (carrier) { + lpa = mii->mdio_read(mii->dev, mii->phy_id, MII_LPA); + dev_info(db->dev, + "%s: link up, %dMbps, %s-duplex, lpa 0x%04X\n", ndev->name, (nsr & NSR_SPEED) ? 10 : 100, - (ncr & NCR_FDX) ? "full" : "half"); - else + (ncr & NCR_FDX) ? "full" : "half", lpa); + } else { dev_info(db->dev, "%s: link down\n", ndev->name); + } } static void @@ -890,9 +904,15 @@ dm9000_init_dm9000(struct net_device *dev) (dev->features & NETIF_F_RXCSUM) ? RCSR_CSUM : 0); iow(db, DM9000_GPCR, GPCR_GEP_CNTL); /* Let GPIO0 output */ + iow(db, DM9000_GPR, 0); - dm9000_phy_write(dev, 0, MII_BMCR, BMCR_RESET); /* PHY RESET */ - dm9000_phy_write(dev, 0, MII_DM_DSPCR, DSPCR_INIT_PARAM); /* Init */ + /* If we are dealing with DM9000B, some extra steps are required: a + * manual phy reset, and setting init params. + */ + if (db->type == TYPE_DM9000B) { + dm9000_phy_write(dev, 0, MII_BMCR, BMCR_RESET); + dm9000_phy_write(dev, 0, MII_DM_DSPCR, DSPCR_INIT_PARAM); + } ncr = (db->flags & DM9000_PLATF_EXT_PHY) ? NCR_EXT_PHY : 0; |