aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/intel/e1000e/80003es2lan.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/ethernet/intel/e1000e/80003es2lan.c')
-rw-r--r--drivers/net/ethernet/intel/e1000e/80003es2lan.c66
1 files changed, 23 insertions, 43 deletions
diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index 4dd18a1f45d2..e73c2c355993 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -26,8 +26,7 @@
*******************************************************************************/
-/*
- * 80003ES2LAN Gigabit Ethernet Controller (Copper)
+/* 80003ES2LAN Gigabit Ethernet Controller (Copper)
* 80003ES2LAN Gigabit Ethernet Controller (Serdes)
*/
@@ -80,7 +79,8 @@
1 = 50-80M
2 = 80-110M
3 = 110-140M
- 4 = >140M */
+ 4 = >140M
+ */
/* Kumeran Mode Control Register (Page 193, Register 16) */
#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800
@@ -95,8 +95,7 @@
/* In-Band Control Register (Page 194, Register 18) */
#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding */
-/*
- * A table for the GG82563 cable length where the range is defined
+/* A table for the GG82563 cable length where the range is defined
* with a lower bound at "index" and the upper bound at
* "index + 5".
*/
@@ -183,8 +182,7 @@ static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw)
size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
E1000_EECD_SIZE_EX_SHIFT);
- /*
- * Added to a constant, "size" becomes the left-shift value
+ /* Added to a constant, "size" becomes the left-shift value
* for setting word_size.
*/
size += NVM_WORD_SIZE_BASE_SHIFT;
@@ -375,8 +373,7 @@ static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
if (!(swfw_sync & (fwmask | swmask)))
break;
- /*
- * Firmware currently using resource (fwmask)
+ /* Firmware currently using resource (fwmask)
* or other software thread using resource (swmask)
*/
e1000e_put_hw_semaphore(hw);
@@ -442,8 +439,7 @@ static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
page_select = GG82563_PHY_PAGE_SELECT;
} else {
- /*
- * Use Alternative Page Select register to access
+ /* Use Alternative Page Select register to access
* registers 30 and 31
*/
page_select = GG82563_PHY_PAGE_SELECT_ALT;
@@ -457,8 +453,7 @@ static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
}
if (hw->dev_spec.e80003es2lan.mdic_wa_enable) {
- /*
- * The "ready" bit in the MDIC register may be incorrectly set
+ /* The "ready" bit in the MDIC register may be incorrectly set
* before the device has completed the "Page Select" MDI
* transaction. So we wait 200us after each MDI command...
*/
@@ -513,8 +508,7 @@ static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
page_select = GG82563_PHY_PAGE_SELECT;
} else {
- /*
- * Use Alternative Page Select register to access
+ /* Use Alternative Page Select register to access
* registers 30 and 31
*/
page_select = GG82563_PHY_PAGE_SELECT_ALT;
@@ -528,8 +522,7 @@ static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
}
if (hw->dev_spec.e80003es2lan.mdic_wa_enable) {
- /*
- * The "ready" bit in the MDIC register may be incorrectly set
+ /* The "ready" bit in the MDIC register may be incorrectly set
* before the device has completed the "Page Select" MDI
* transaction. So we wait 200us after each MDI command...
*/
@@ -618,8 +611,7 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
u16 phy_data;
bool link;
- /*
- * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
+ /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
* forced whenever speed and duplex are forced.
*/
ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
@@ -657,8 +649,7 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
return ret_val;
if (!link) {
- /*
- * We didn't get link.
+ /* We didn't get link.
* Reset the DSP and cross our fingers.
*/
ret_val = e1000e_phy_reset_dsp(hw);
@@ -677,8 +668,7 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- /*
- * Resetting the phy means we need to verify the TX_CLK corresponds
+ /* Resetting the phy means we need to verify the TX_CLK corresponds
* to the link speed. 10Mbps -> 2.5MHz, else 25MHz.
*/
phy_data &= ~GG82563_MSCR_TX_CLK_MASK;
@@ -687,8 +677,7 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
else
phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25;
- /*
- * In addition, we must re-enable CRS on Tx for both half and full
+ /* In addition, we must re-enable CRS on Tx for both half and full
* duplex.
*/
phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
@@ -766,8 +755,7 @@ static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw)
s32 ret_val;
u16 kum_reg_data;
- /*
- * Prevent the PCI-E bus from sticking if there is no TLP connection
+ /* Prevent the PCI-E bus from sticking if there is no TLP connection
* on the last TLP read/write transaction when MAC is reset.
*/
ret_val = e1000e_disable_pcie_master(hw);
@@ -899,8 +887,7 @@ static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
hw->dev_spec.e80003es2lan.mdic_wa_enable = false;
}
- /*
- * Clear all of the statistics registers (clear on read). It is
+ /* Clear all of the statistics registers (clear on read). It is
* important that we do this after we have tried to establish link
* because the symbol error count will increment wildly if there
* is no link.
@@ -945,8 +932,7 @@ static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw)
reg |= (1 << 28);
ew32(TARC(1), reg);
- /*
- * Disable IPv6 extension header parsing because some malformed
+ /* Disable IPv6 extension header parsing because some malformed
* IPv6 headers can hang the Rx.
*/
reg = er32(RFCTL);
@@ -979,8 +965,7 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- /*
- * Options:
+ /* Options:
* MDI/MDI-X = 0 (default)
* 0 - Auto for all speeds
* 1 - MDI mode
@@ -1006,8 +991,7 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
break;
}
- /*
- * Options:
+ /* Options:
* disable_polarity_correction = 0 (default)
* Automatic Correction for Reversed Cable Polarity
* 0 - Disabled
@@ -1065,8 +1049,7 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- /*
- * Do not init these registers when the HW is in IAMT mode, since the
+ /* Do not init these registers when the HW is in IAMT mode, since the
* firmware will have already initialized them. We only initialize
* them if the HW is not in IAMT mode.
*/
@@ -1087,8 +1070,7 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
return ret_val;
}
- /*
- * Workaround: Disable padding in Kumeran interface in the MAC
+ /* Workaround: Disable padding in Kumeran interface in the MAC
* and in the PHY to avoid CRC errors.
*/
ret_val = e1e_rphy(hw, GG82563_PHY_INBAND_CTRL, &data);
@@ -1121,8 +1103,7 @@ static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw)
ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
ew32(CTRL, ctrl);
- /*
- * Set the mac to wait the maximum time between each
+ /* Set the mac to wait the maximum time between each
* iteration and increase the max iterations when
* polling the phy; this fixes erroneous timeouts at 10Mbps.
*/
@@ -1352,8 +1333,7 @@ static s32 e1000_read_mac_addr_80003es2lan(struct e1000_hw *hw)
{
s32 ret_val = 0;
- /*
- * If there's an alternate MAC address place it in RAR0
+ /* If there's an alternate MAC address place it in RAR0
* so that it will override the Si installed default perm
* address.
*/
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.