diff options
Diffstat (limited to 'drivers/net/ethernet/intel/e1000e/mac.c')
| -rw-r--r-- | drivers/net/ethernet/intel/e1000e/mac.c | 164 |
1 files changed, 144 insertions, 20 deletions
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c index 54d9dafaf126..b78e02174601 100644 --- a/drivers/net/ethernet/intel/e1000e/mac.c +++ b/drivers/net/ethernet/intel/e1000e/mac.c @@ -1,7 +1,7 @@ /******************************************************************************* Intel PRO/1000 Linux driver - Copyright(c) 1999 - 2012 Intel Corporation. + Copyright(c) 1999 - 2013 Intel Corporation. This program is free software; you can redistribute it and/or modify it under the terms and conditions of the GNU General Public License, @@ -165,7 +165,7 @@ void e1000e_init_rx_addrs(struct e1000_hw *hw, u16 rar_count) s32 e1000_check_alt_mac_addr_generic(struct e1000_hw *hw) { u32 i; - s32 ret_val = 0; + s32 ret_val; u16 offset, nvm_alt_mac_addr_offset, nvm_data; u8 alt_mac_addr[ETH_ALEN]; @@ -1021,6 +1021,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) { struct e1000_mac_info *mac = &hw->mac; s32 ret_val = 0; + u32 pcs_status_reg, pcs_adv_reg, pcs_lp_ability_reg, pcs_ctrl_reg; u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg; u16 speed, duplex; @@ -1052,14 +1053,14 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) * has completed. We read this twice because this reg has * some "sticky" (latched) bits. */ - ret_val = e1e_rphy(hw, PHY_STATUS, &mii_status_reg); + ret_val = e1e_rphy(hw, MII_BMSR, &mii_status_reg); if (ret_val) return ret_val; - ret_val = e1e_rphy(hw, PHY_STATUS, &mii_status_reg); + ret_val = e1e_rphy(hw, MII_BMSR, &mii_status_reg); if (ret_val) return ret_val; - if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) { + if (!(mii_status_reg & BMSR_ANEGCOMPLETE)) { e_dbg("Copper PHY and Auto Neg has not completed.\n"); return ret_val; } @@ -1070,11 +1071,10 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) * Page Ability Register (Address 5) to determine how * flow control was negotiated. */ - ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg); + ret_val = e1e_rphy(hw, MII_ADVERTISE, &mii_nway_adv_reg); if (ret_val) return ret_val; - ret_val = - e1e_rphy(hw, PHY_LP_ABILITY, &mii_nway_lp_ability_reg); + ret_val = e1e_rphy(hw, MII_LPA, &mii_nway_lp_ability_reg); if (ret_val) return ret_val; @@ -1111,8 +1111,8 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) * 1 | DC | 1 | DC | E1000_fc_full * */ - if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && - (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { + if ((mii_nway_adv_reg & ADVERTISE_PAUSE_CAP) && + (mii_nway_lp_ability_reg & LPA_PAUSE_CAP)) { /* Now we need to check if the user selected Rx ONLY * of pause frames. In this case, we had to advertise * FULL flow control because we could not advertise Rx @@ -1134,10 +1134,10 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) *-------|---------|-------|---------|-------------------- * 0 | 1 | 1 | 1 | e1000_fc_tx_pause */ - else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && - (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && - (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && - (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { + else if (!(mii_nway_adv_reg & ADVERTISE_PAUSE_CAP) && + (mii_nway_adv_reg & ADVERTISE_PAUSE_ASYM) && + (mii_nway_lp_ability_reg & LPA_PAUSE_CAP) && + (mii_nway_lp_ability_reg & LPA_PAUSE_ASYM)) { hw->fc.current_mode = e1000_fc_tx_pause; e_dbg("Flow Control = Tx PAUSE frames only.\n"); } @@ -1148,10 +1148,10 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) *-------|---------|-------|---------|-------------------- * 1 | 1 | 0 | 1 | e1000_fc_rx_pause */ - else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && - (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && - !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && - (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { + else if ((mii_nway_adv_reg & ADVERTISE_PAUSE_CAP) && + (mii_nway_adv_reg & ADVERTISE_PAUSE_ASYM) && + !(mii_nway_lp_ability_reg & LPA_PAUSE_CAP) && + (mii_nway_lp_ability_reg & LPA_PAUSE_ASYM)) { hw->fc.current_mode = e1000_fc_rx_pause; e_dbg("Flow Control = Rx PAUSE frames only.\n"); } else { @@ -1185,6 +1185,130 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) } } + /* Check for the case where we have SerDes media and auto-neg is + * enabled. In this case, we need to check and see if Auto-Neg + * has completed, and if so, how the PHY and link partner has + * flow control configured. + */ + if ((hw->phy.media_type == e1000_media_type_internal_serdes) && + mac->autoneg) { + /* Read the PCS_LSTS and check to see if AutoNeg + * has completed. + */ + pcs_status_reg = er32(PCS_LSTAT); + + if (!(pcs_status_reg & E1000_PCS_LSTS_AN_COMPLETE)) { + e_dbg("PCS Auto Neg has not completed.\n"); + return ret_val; + } + + /* The AutoNeg process has completed, so we now need to + * read both the Auto Negotiation Advertisement + * Register (PCS_ANADV) and the Auto_Negotiation Base + * Page Ability Register (PCS_LPAB) to determine how + * flow control was negotiated. + */ + pcs_adv_reg = er32(PCS_ANADV); + pcs_lp_ability_reg = er32(PCS_LPAB); + + /* Two bits in the Auto Negotiation Advertisement Register + * (PCS_ANADV) and two bits in the Auto Negotiation Base + * Page Ability Register (PCS_LPAB) determine flow control + * for both the PHY and the link partner. The following + * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, + * 1999, describes these PAUSE resolution bits and how flow + * control is determined based upon these settings. + * NOTE: DC = Don't Care + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution + *-------|---------|-------|---------|-------------------- + * 0 | 0 | DC | DC | e1000_fc_none + * 0 | 1 | 0 | DC | e1000_fc_none + * 0 | 1 | 1 | 0 | e1000_fc_none + * 0 | 1 | 1 | 1 | e1000_fc_tx_pause + * 1 | 0 | 0 | DC | e1000_fc_none + * 1 | DC | 1 | DC | e1000_fc_full + * 1 | 1 | 0 | 0 | e1000_fc_none + * 1 | 1 | 0 | 1 | e1000_fc_rx_pause + * + * Are both PAUSE bits set to 1? If so, this implies + * Symmetric Flow Control is enabled at both ends. The + * ASM_DIR bits are irrelevant per the spec. + * + * For Symmetric Flow Control: + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | DC | 1 | DC | e1000_fc_full + * + */ + if ((pcs_adv_reg & E1000_TXCW_PAUSE) && + (pcs_lp_ability_reg & E1000_TXCW_PAUSE)) { + /* Now we need to check if the user selected Rx ONLY + * of pause frames. In this case, we had to advertise + * FULL flow control because we could not advertise Rx + * ONLY. Hence, we must now check to see if we need to + * turn OFF the TRANSMISSION of PAUSE frames. + */ + if (hw->fc.requested_mode == e1000_fc_full) { + hw->fc.current_mode = e1000_fc_full; + e_dbg("Flow Control = FULL.\n"); + } else { + hw->fc.current_mode = e1000_fc_rx_pause; + e_dbg("Flow Control = Rx PAUSE frames only.\n"); + } + } + /* For receiving PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 0 | 1 | 1 | 1 | e1000_fc_tx_pause + */ + else if (!(pcs_adv_reg & E1000_TXCW_PAUSE) && + (pcs_adv_reg & E1000_TXCW_ASM_DIR) && + (pcs_lp_ability_reg & E1000_TXCW_PAUSE) && + (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) { + hw->fc.current_mode = e1000_fc_tx_pause; + e_dbg("Flow Control = Tx PAUSE frames only.\n"); + } + /* For transmitting PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | 1 | 0 | 1 | e1000_fc_rx_pause + */ + else if ((pcs_adv_reg & E1000_TXCW_PAUSE) && + (pcs_adv_reg & E1000_TXCW_ASM_DIR) && + !(pcs_lp_ability_reg & E1000_TXCW_PAUSE) && + (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) { + hw->fc.current_mode = e1000_fc_rx_pause; + e_dbg("Flow Control = Rx PAUSE frames only.\n"); + } else { + /* Per the IEEE spec, at this point flow control + * should be disabled. + */ + hw->fc.current_mode = e1000_fc_none; + e_dbg("Flow Control = NONE.\n"); + } + + /* Now we call a subroutine to actually force the MAC + * controller to use the correct flow control settings. + */ + pcs_ctrl_reg = er32(PCS_LCTL); + pcs_ctrl_reg |= E1000_PCS_LCTL_FORCE_FCTRL; + ew32(PCS_LCTL, pcs_ctrl_reg); + + ret_val = e1000e_force_mac_fc(hw); + if (ret_val) { + e_dbg("Error forcing flow control settings\n"); + return ret_val; + } + } + return 0; } @@ -1231,8 +1355,8 @@ s32 e1000e_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed, * Sets the speed and duplex to gigabit full duplex (the only possible option) * for fiber/serdes links. **/ -s32 e1000e_get_speed_and_duplex_fiber_serdes(struct e1000_hw *hw, u16 *speed, - u16 *duplex) +s32 e1000e_get_speed_and_duplex_fiber_serdes(struct e1000_hw __always_unused + *hw, u16 *speed, u16 *duplex) { *speed = SPEED_1000; *duplex = FULL_DUPLEX; |