diff options
Diffstat (limited to 'drivers/net/ethernet/intel/e1000e/netdev.c')
| -rw-r--r-- | drivers/net/ethernet/intel/e1000e/netdev.c | 372 |
1 files changed, 216 insertions, 156 deletions
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c index 757a54c39eef..900b3ab998bd 100644 --- a/drivers/net/ethernet/intel/e1000e/netdev.c +++ b/drivers/net/ethernet/intel/e1000e/netdev.c @@ -3550,6 +3550,7 @@ s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca) case e1000_pch_tgp: case e1000_pch_adp: case e1000_pch_mtp: + case e1000_pch_lnp: if (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI) { /* Stable 24MHz frequency */ incperiod = INCPERIOD_24MHZ; @@ -4068,6 +4069,7 @@ void e1000e_reset(struct e1000_adapter *adapter) case e1000_pch_tgp: case e1000_pch_adp: case e1000_pch_mtp: + case e1000_pch_lnp: fc->refresh_time = 0xFFFF; fc->pause_time = 0xFFFF; @@ -6343,42 +6345,110 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter) u32 mac_data; u16 phy_data; - /* Disable the periodic inband message, - * don't request PCIe clock in K1 page770_17[10:9] = 10b - */ - e1e_rphy(hw, HV_PM_CTRL, &phy_data); - phy_data &= ~HV_PM_CTRL_K1_CLK_REQ; - phy_data |= BIT(10); - e1e_wphy(hw, HV_PM_CTRL, phy_data); + if (er32(FWSM) & E1000_ICH_FWSM_FW_VALID) { + /* Request ME configure the device for S0ix */ + mac_data = er32(H2ME); + mac_data |= E1000_H2ME_START_DPG; + mac_data &= ~E1000_H2ME_EXIT_DPG; + ew32(H2ME, mac_data); + } else { + /* Request driver configure the device to S0ix */ + /* Disable the periodic inband message, + * don't request PCIe clock in K1 page770_17[10:9] = 10b + */ + e1e_rphy(hw, HV_PM_CTRL, &phy_data); + phy_data &= ~HV_PM_CTRL_K1_CLK_REQ; + phy_data |= BIT(10); + e1e_wphy(hw, HV_PM_CTRL, phy_data); - /* Make sure we don't exit K1 every time a new packet arrives - * 772_29[5] = 1 CS_Mode_Stay_In_K1 - */ - e1e_rphy(hw, I217_CGFREG, &phy_data); - phy_data |= BIT(5); - e1e_wphy(hw, I217_CGFREG, phy_data); + /* Make sure we don't exit K1 every time a new packet arrives + * 772_29[5] = 1 CS_Mode_Stay_In_K1 + */ + e1e_rphy(hw, I217_CGFREG, &phy_data); + phy_data |= BIT(5); + e1e_wphy(hw, I217_CGFREG, phy_data); - /* Change the MAC/PHY interface to SMBus - * Force the SMBus in PHY page769_23[0] = 1 - * Force the SMBus in MAC CTRL_EXT[11] = 1 - */ - e1e_rphy(hw, CV_SMB_CTRL, &phy_data); - phy_data |= CV_SMB_CTRL_FORCE_SMBUS; - e1e_wphy(hw, CV_SMB_CTRL, phy_data); - mac_data = er32(CTRL_EXT); - mac_data |= E1000_CTRL_EXT_FORCE_SMBUS; - ew32(CTRL_EXT, mac_data); + /* Change the MAC/PHY interface to SMBus + * Force the SMBus in PHY page769_23[0] = 1 + * Force the SMBus in MAC CTRL_EXT[11] = 1 + */ + e1e_rphy(hw, CV_SMB_CTRL, &phy_data); + phy_data |= CV_SMB_CTRL_FORCE_SMBUS; + e1e_wphy(hw, CV_SMB_CTRL, phy_data); + mac_data = er32(CTRL_EXT); + mac_data |= E1000_CTRL_EXT_FORCE_SMBUS; + ew32(CTRL_EXT, mac_data); + + /* DFT control: PHY bit: page769_20[0] = 1 + * page769_20[7] - PHY PLL stop + * page769_20[8] - PHY go to the electrical idle + * page769_20[9] - PHY serdes disable + * Gate PPW via EXTCNF_CTRL - set 0x0F00[7] = 1 + */ + e1e_rphy(hw, I82579_DFT_CTRL, &phy_data); + phy_data |= BIT(0); + phy_data |= BIT(7); + phy_data |= BIT(8); + phy_data |= BIT(9); + e1e_wphy(hw, I82579_DFT_CTRL, phy_data); + + mac_data = er32(EXTCNF_CTRL); + mac_data |= E1000_EXTCNF_CTRL_GATE_PHY_CFG; + ew32(EXTCNF_CTRL, mac_data); + + /* Enable the Dynamic Power Gating in the MAC */ + mac_data = er32(FEXTNVM7); + mac_data |= BIT(22); + ew32(FEXTNVM7, mac_data); + + /* Disable disconnected cable conditioning for Power Gating */ + mac_data = er32(DPGFR); + mac_data |= BIT(2); + ew32(DPGFR, mac_data); + + /* Don't wake from dynamic Power Gating with clock request */ + mac_data = er32(FEXTNVM12); + mac_data |= BIT(12); + ew32(FEXTNVM12, mac_data); + + /* Ungate PGCB clock */ + mac_data = er32(FEXTNVM9); + mac_data &= ~BIT(28); + ew32(FEXTNVM9, mac_data); + + /* Enable K1 off to enable mPHY Power Gating */ + mac_data = er32(FEXTNVM6); + mac_data |= BIT(31); + ew32(FEXTNVM6, mac_data); + + /* Enable mPHY power gating for any link and speed */ + mac_data = er32(FEXTNVM8); + mac_data |= BIT(9); + ew32(FEXTNVM8, mac_data); + + /* Enable the Dynamic Clock Gating in the DMA and MAC */ + mac_data = er32(CTRL_EXT); + mac_data |= E1000_CTRL_EXT_DMA_DYN_CLK_EN; + ew32(CTRL_EXT, mac_data); + + /* No MAC DPG gating SLP_S0 in modern standby + * Switch the logic of the lanphypc to use PMC counter + */ + mac_data = er32(FEXTNVM5); + mac_data |= BIT(7); + ew32(FEXTNVM5, mac_data); + } - /* DFT control: PHY bit: page769_20[0] = 1 - * Gate PPW via EXTCNF_CTRL - set 0x0F00[7] = 1 - */ - e1e_rphy(hw, I82579_DFT_CTRL, &phy_data); - phy_data |= BIT(0); - e1e_wphy(hw, I82579_DFT_CTRL, phy_data); + /* Disable the time synchronization clock */ + mac_data = er32(FEXTNVM7); + mac_data |= BIT(31); + mac_data &= ~BIT(0); + ew32(FEXTNVM7, mac_data); - mac_data = er32(EXTCNF_CTRL); - mac_data |= E1000_EXTCNF_CTRL_GATE_PHY_CFG; - ew32(EXTCNF_CTRL, mac_data); + /* Dynamic Power Gating Enable */ + mac_data = er32(CTRL_EXT); + mac_data |= BIT(3); + ew32(CTRL_EXT, mac_data); /* Check MAC Tx/Rx packet buffer pointers. * Reset MAC Tx/Rx packet buffer pointers to suppress any @@ -6414,148 +6484,130 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter) mac_data = er32(RDFPC); if (mac_data) ew32(RDFPC, 0); - - /* Enable the Dynamic Power Gating in the MAC */ - mac_data = er32(FEXTNVM7); - mac_data |= BIT(22); - ew32(FEXTNVM7, mac_data); - - /* Disable the time synchronization clock */ - mac_data = er32(FEXTNVM7); - mac_data |= BIT(31); - mac_data &= ~BIT(0); - ew32(FEXTNVM7, mac_data); - - /* Dynamic Power Gating Enable */ - mac_data = er32(CTRL_EXT); - mac_data |= BIT(3); - ew32(CTRL_EXT, mac_data); - - /* Disable disconnected cable conditioning for Power Gating */ - mac_data = er32(DPGFR); - mac_data |= BIT(2); - ew32(DPGFR, mac_data); - - /* Don't wake from dynamic Power Gating with clock request */ - mac_data = er32(FEXTNVM12); - mac_data |= BIT(12); - ew32(FEXTNVM12, mac_data); - - /* Ungate PGCB clock */ - mac_data = er32(FEXTNVM9); - mac_data &= ~BIT(28); - ew32(FEXTNVM9, mac_data); - - /* Enable K1 off to enable mPHY Power Gating */ - mac_data = er32(FEXTNVM6); - mac_data |= BIT(31); - ew32(FEXTNVM6, mac_data); - - /* Enable mPHY power gating for any link and speed */ - mac_data = er32(FEXTNVM8); - mac_data |= BIT(9); - ew32(FEXTNVM8, mac_data); - - /* Enable the Dynamic Clock Gating in the DMA and MAC */ - mac_data = er32(CTRL_EXT); - mac_data |= E1000_CTRL_EXT_DMA_DYN_CLK_EN; - ew32(CTRL_EXT, mac_data); - - /* No MAC DPG gating SLP_S0 in modern standby - * Switch the logic of the lanphypc to use PMC counter - */ - mac_data = er32(FEXTNVM5); - mac_data |= BIT(7); - ew32(FEXTNVM5, mac_data); } static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter) { struct e1000_hw *hw = &adapter->hw; + bool firmware_bug = false; u32 mac_data; u16 phy_data; + u32 i = 0; + + if (er32(FWSM) & E1000_ICH_FWSM_FW_VALID) { + /* Request ME unconfigure the device from S0ix */ + mac_data = er32(H2ME); + mac_data &= ~E1000_H2ME_START_DPG; + mac_data |= E1000_H2ME_EXIT_DPG; + ew32(H2ME, mac_data); + + /* Poll up to 2.5 seconds for ME to unconfigure DPG. + * If this takes more than 1 second, show a warning indicating a + * firmware bug + */ + while (!(er32(EXFWSM) & E1000_EXFWSM_DPG_EXIT_DONE)) { + if (i > 100 && !firmware_bug) + firmware_bug = true; - /* Disable the Dynamic Power Gating in the MAC */ - mac_data = er32(FEXTNVM7); - mac_data &= 0xFFBFFFFF; - ew32(FEXTNVM7, mac_data); + if (i++ == 250) { + e_dbg("Timeout (firmware bug): %d msec\n", + i * 10); + break; + } - /* Enable the time synchronization clock */ - mac_data = er32(FEXTNVM7); - mac_data |= BIT(0); - ew32(FEXTNVM7, mac_data); + usleep_range(10000, 11000); + } + if (firmware_bug) + e_warn("DPG_EXIT_DONE took %d msec. This is a firmware bug\n", + i * 10); + else + e_dbg("DPG_EXIT_DONE cleared after %d msec\n", i * 10); + } else { + /* Request driver unconfigure the device from S0ix */ + + /* Disable the Dynamic Power Gating in the MAC */ + mac_data = er32(FEXTNVM7); + mac_data &= 0xFFBFFFFF; + ew32(FEXTNVM7, mac_data); + + /* Disable mPHY power gating for any link and speed */ + mac_data = er32(FEXTNVM8); + mac_data &= ~BIT(9); + ew32(FEXTNVM8, mac_data); + + /* Disable K1 off */ + mac_data = er32(FEXTNVM6); + mac_data &= ~BIT(31); + ew32(FEXTNVM6, mac_data); + + /* Disable Ungate PGCB clock */ + mac_data = er32(FEXTNVM9); + mac_data |= BIT(28); + ew32(FEXTNVM9, mac_data); + + /* Cancel not waking from dynamic + * Power Gating with clock request + */ + mac_data = er32(FEXTNVM12); + mac_data &= ~BIT(12); + ew32(FEXTNVM12, mac_data); - /* Disable mPHY power gating for any link and speed */ - mac_data = er32(FEXTNVM8); - mac_data &= ~BIT(9); - ew32(FEXTNVM8, mac_data); + /* Cancel disable disconnected cable conditioning + * for Power Gating + */ + mac_data = er32(DPGFR); + mac_data &= ~BIT(2); + ew32(DPGFR, mac_data); - /* Disable K1 off */ - mac_data = er32(FEXTNVM6); - mac_data &= ~BIT(31); - ew32(FEXTNVM6, mac_data); + /* Disable the Dynamic Clock Gating in the DMA and MAC */ + mac_data = er32(CTRL_EXT); + mac_data &= 0xFFF7FFFF; + ew32(CTRL_EXT, mac_data); - /* Disable Ungate PGCB clock */ - mac_data = er32(FEXTNVM9); - mac_data |= BIT(28); - ew32(FEXTNVM9, mac_data); + /* Revert the lanphypc logic to use the internal Gbe counter + * and not the PMC counter + */ + mac_data = er32(FEXTNVM5); + mac_data &= 0xFFFFFF7F; + ew32(FEXTNVM5, mac_data); - /* Cancel not waking from dynamic - * Power Gating with clock request - */ - mac_data = er32(FEXTNVM12); - mac_data &= ~BIT(12); - ew32(FEXTNVM12, mac_data); + /* Enable the periodic inband message, + * Request PCIe clock in K1 page770_17[10:9] =01b + */ + e1e_rphy(hw, HV_PM_CTRL, &phy_data); + phy_data &= 0xFBFF; + phy_data |= HV_PM_CTRL_K1_CLK_REQ; + e1e_wphy(hw, HV_PM_CTRL, phy_data); - /* Cancel disable disconnected cable conditioning - * for Power Gating - */ - mac_data = er32(DPGFR); - mac_data &= ~BIT(2); - ew32(DPGFR, mac_data); + /* Return back configuration + * 772_29[5] = 0 CS_Mode_Stay_In_K1 + */ + e1e_rphy(hw, I217_CGFREG, &phy_data); + phy_data &= 0xFFDF; + e1e_wphy(hw, I217_CGFREG, phy_data); + + /* Change the MAC/PHY interface to Kumeran + * Unforce the SMBus in PHY page769_23[0] = 0 + * Unforce the SMBus in MAC CTRL_EXT[11] = 0 + */ + e1e_rphy(hw, CV_SMB_CTRL, &phy_data); + phy_data &= ~CV_SMB_CTRL_FORCE_SMBUS; + e1e_wphy(hw, CV_SMB_CTRL, phy_data); + mac_data = er32(CTRL_EXT); + mac_data &= ~E1000_CTRL_EXT_FORCE_SMBUS; + ew32(CTRL_EXT, mac_data); + } /* Disable Dynamic Power Gating */ mac_data = er32(CTRL_EXT); mac_data &= 0xFFFFFFF7; ew32(CTRL_EXT, mac_data); - /* Disable the Dynamic Clock Gating in the DMA and MAC */ - mac_data = er32(CTRL_EXT); - mac_data &= 0xFFF7FFFF; - ew32(CTRL_EXT, mac_data); - - /* Revert the lanphypc logic to use the internal Gbe counter - * and not the PMC counter - */ - mac_data = er32(FEXTNVM5); - mac_data &= 0xFFFFFF7F; - ew32(FEXTNVM5, mac_data); - - /* Enable the periodic inband message, - * Request PCIe clock in K1 page770_17[10:9] =01b - */ - e1e_rphy(hw, HV_PM_CTRL, &phy_data); - phy_data &= 0xFBFF; - phy_data |= HV_PM_CTRL_K1_CLK_REQ; - e1e_wphy(hw, HV_PM_CTRL, phy_data); - - /* Return back configuration - * 772_29[5] = 0 CS_Mode_Stay_In_K1 - */ - e1e_rphy(hw, I217_CGFREG, &phy_data); - phy_data &= 0xFFDF; - e1e_wphy(hw, I217_CGFREG, phy_data); - - /* Change the MAC/PHY interface to Kumeran - * Unforce the SMBus in PHY page769_23[0] = 0 - * Unforce the SMBus in MAC CTRL_EXT[11] = 0 - */ - e1e_rphy(hw, CV_SMB_CTRL, &phy_data); - phy_data &= ~CV_SMB_CTRL_FORCE_SMBUS; - e1e_wphy(hw, CV_SMB_CTRL, phy_data); - mac_data = er32(CTRL_EXT); - mac_data &= ~E1000_CTRL_EXT_FORCE_SMBUS; - ew32(CTRL_EXT, mac_data); + /* Enable the time synchronization clock */ + mac_data = er32(FEXTNVM7); + mac_data &= ~BIT(31); + mac_data |= BIT(0); + ew32(FEXTNVM7, mac_data); } static int e1000e_pm_freeze(struct device *dev) @@ -7302,7 +7354,7 @@ static const struct net_device_ops e1000e_netdev_ops = { .ndo_set_rx_mode = e1000e_set_rx_mode, .ndo_set_mac_address = e1000_set_mac, .ndo_change_mtu = e1000_change_mtu, - .ndo_do_ioctl = e1000_ioctl, + .ndo_eth_ioctl = e1000_ioctl, .ndo_tx_timeout = e1000_tx_timeout, .ndo_validate_addr = eth_validate_addr, @@ -7677,7 +7729,7 @@ err_dma: * @pdev: PCI device information struct * * e1000_remove is called by the PCI subsystem to alert the driver - * that it should release a PCI device. The could be caused by a + * that it should release a PCI device. This could be caused by a * Hot-Plug event, or because the driver is going to be removed from * memory. **/ @@ -7850,14 +7902,22 @@ static const struct pci_device_id e1000_pci_tbl[] = { { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_V14), board_pch_cnp }, { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_LM15), board_pch_cnp }, { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_V15), board_pch_cnp }, + { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_LM23), board_pch_cnp }, + { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_V23), board_pch_cnp }, { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_LM16), board_pch_cnp }, { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_V16), board_pch_cnp }, { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_LM17), board_pch_cnp }, { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_V17), board_pch_cnp }, + { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_LM22), board_pch_cnp }, + { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_RPL_I219_V22), board_pch_cnp }, { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_LM18), board_pch_cnp }, { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_V18), board_pch_cnp }, { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_LM19), board_pch_cnp }, { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_MTP_I219_V19), board_pch_cnp }, + { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_LM20), board_pch_cnp }, + { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_V20), board_pch_cnp }, + { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_LM21), board_pch_cnp }, + { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LNP_I219_V21), board_pch_cnp }, { 0, 0, 0, 0, 0, 0, 0 } /* terminate list */ }; |