aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/intel/igb/e1000_82575.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/ethernet/intel/igb/e1000_82575.c')
-rw-r--r--drivers/net/ethernet/intel/igb/e1000_82575.c294
1 files changed, 212 insertions, 82 deletions
diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c b/drivers/net/ethernet/intel/igb/e1000_82575.c
index b64542acfa34..ff6a17cb1362 100644
--- a/drivers/net/ethernet/intel/igb/e1000_82575.c
+++ b/drivers/net/ethernet/intel/igb/e1000_82575.c
@@ -100,6 +100,7 @@ static bool igb_sgmii_uses_mdio_82575(struct e1000_hw *hw)
break;
case e1000_82580:
case e1000_i350:
+ case e1000_i354:
case e1000_i210:
case e1000_i211:
reg = rd32(E1000_MDICNFG);
@@ -149,6 +150,7 @@ static s32 igb_init_phy_params_82575(struct e1000_hw *hw)
switch (hw->mac.type) {
case e1000_82580:
case e1000_i350:
+ case e1000_i354:
phy->ops.read_reg = igb_read_phy_reg_82580;
phy->ops.write_reg = igb_write_phy_reg_82580;
break;
@@ -174,13 +176,14 @@ static s32 igb_init_phy_params_82575(struct e1000_hw *hw)
/* Verify phy id and set remaining function pointers */
switch (phy->id) {
+ case M88E1545_E_PHY_ID:
case I347AT4_E_PHY_ID:
case M88E1112_E_PHY_ID:
case M88E1111_I_PHY_ID:
phy->type = e1000_phy_m88;
+ phy->ops.check_polarity = igb_check_polarity_m88;
phy->ops.get_phy_info = igb_get_phy_info_m88;
- if (phy->id == I347AT4_E_PHY_ID ||
- phy->id == M88E1112_E_PHY_ID)
+ if (phy->id != M88E1111_I_PHY_ID)
phy->ops.get_cable_length =
igb_get_cable_length_m88_gen2;
else
@@ -227,7 +230,7 @@ out:
* igb_init_nvm_params_82575 - Init NVM func ptrs.
* @hw: pointer to the HW structure
**/
-s32 igb_init_nvm_params_82575(struct e1000_hw *hw)
+static s32 igb_init_nvm_params_82575(struct e1000_hw *hw)
{
struct e1000_nvm_info *nvm = &hw->nvm;
u32 eecd = rd32(E1000_EECD);
@@ -287,6 +290,7 @@ s32 igb_init_nvm_params_82575(struct e1000_hw *hw)
nvm->ops.read = igb_read_nvm_spi;
nvm->ops.write = igb_write_nvm_spi;
break;
+ case e1000_i354:
case e1000_i350:
nvm->ops.validate = igb_validate_nvm_checksum_i350;
nvm->ops.update = igb_update_nvm_checksum_i350;
@@ -352,6 +356,7 @@ static s32 igb_init_mac_params_82575(struct e1000_hw *hw)
mac->rar_entry_count = E1000_RAR_ENTRIES_82580;
break;
case e1000_i350:
+ case e1000_i354:
mac->rar_entry_count = E1000_RAR_ENTRIES_I350;
break;
default:
@@ -384,6 +389,9 @@ static s32 igb_init_mac_params_82575(struct e1000_hw *hw)
dev_spec->eee_disable = false;
else
dev_spec->eee_disable = true;
+ /* Allow a single clear of the SW semaphore on I210 and newer */
+ if (mac->type >= e1000_i210)
+ dev_spec->clear_semaphore_once = true;
/* physical interface link setup */
mac->ops.setup_physical_interface =
(hw->phy.media_type == e1000_media_type_copper)
@@ -435,8 +443,6 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
mac->type = e1000_i350;
break;
case E1000_DEV_ID_I210_COPPER:
- case E1000_DEV_ID_I210_COPPER_OEM1:
- case E1000_DEV_ID_I210_COPPER_IT:
case E1000_DEV_ID_I210_FIBER:
case E1000_DEV_ID_I210_SERDES:
case E1000_DEV_ID_I210_SGMII:
@@ -445,14 +451,18 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
case E1000_DEV_ID_I211_COPPER:
mac->type = e1000_i211;
break;
+ case E1000_DEV_ID_I354_BACKPLANE_1GBPS:
+ case E1000_DEV_ID_I354_SGMII:
+ case E1000_DEV_ID_I354_BACKPLANE_2_5GBPS:
+ mac->type = e1000_i354;
+ break;
default:
return -E1000_ERR_MAC_INIT;
break;
}
/* Set media type */
- /*
- * The 82575 uses bits 22:23 for link mode. The mode can be changed
+ /* The 82575 uses bits 22:23 for link mode. The mode can be changed
* based on the EEPROM. We cannot rely upon device ID. There
* is no distinguishable difference between fiber and internal
* SerDes mode on the 82575. There can be an external PHY attached
@@ -621,8 +631,7 @@ static s32 igb_get_phy_id_82575(struct e1000_hw *hw)
u32 ctrl_ext;
u32 mdic;
- /*
- * For SGMII PHYs, we try the list of possible addresses until
+ /* For SGMII PHYs, we try the list of possible addresses until
* we find one that works. For non-SGMII PHYs
* (e.g. integrated copper PHYs), an address of 1 should
* work. The result of this function should mean phy->phy_addr
@@ -644,6 +653,7 @@ static s32 igb_get_phy_id_82575(struct e1000_hw *hw)
break;
case e1000_82580:
case e1000_i350:
+ case e1000_i354:
case e1000_i210:
case e1000_i211:
mdic = rd32(E1000_MDICNFG);
@@ -665,8 +675,7 @@ static s32 igb_get_phy_id_82575(struct e1000_hw *hw)
wrfl();
msleep(300);
- /*
- * The address field in the I2CCMD register is 3 bits and 0 is invalid.
+ /* The address field in the I2CCMD register is 3 bits and 0 is invalid.
* Therefore, we need to test 1-7
*/
for (phy->addr = 1; phy->addr < 8; phy->addr++) {
@@ -674,8 +683,7 @@ static s32 igb_get_phy_id_82575(struct e1000_hw *hw)
if (ret_val == 0) {
hw_dbg("Vendor ID 0x%08X read at address %u\n",
phy_id, phy->addr);
- /*
- * At the time of this writing, The M88 part is
+ /* At the time of this writing, The M88 part is
* the only supported SGMII PHY product.
*/
if (phy_id == M88_VENDOR)
@@ -711,15 +719,13 @@ static s32 igb_phy_hw_reset_sgmii_82575(struct e1000_hw *hw)
{
s32 ret_val;
- /*
- * This isn't a true "hard" reset, but is the only reset
+ /* This isn't a true "hard" reset, but is the only reset
* available to us at this time.
*/
hw_dbg("Soft resetting SGMII attached PHY...\n");
- /*
- * SFP documentation requires the following to configure the SPF module
+ /* SFP documentation requires the following to configure the SPF module
* to work on SGMII. No further documentation is given.
*/
ret_val = hw->phy.ops.write_reg(hw, 0x1B, 0x8084);
@@ -774,8 +780,7 @@ static s32 igb_set_d0_lplu_state_82575(struct e1000_hw *hw, bool active)
data &= ~IGP02E1000_PM_D0_LPLU;
ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT,
data);
- /*
- * LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used
* during Dx states where the power conservation is most
* important. During driver activity we should enable
* SmartSpeed, so performance is maintained.
@@ -838,8 +843,7 @@ static s32 igb_set_d0_lplu_state_82580(struct e1000_hw *hw, bool active)
} else {
data &= ~E1000_82580_PM_D0_LPLU;
- /*
- * LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used
* during Dx states where the power conservation is most
* important. During driver activity we should enable
* SmartSpeed, so performance is maintained.
@@ -867,7 +871,7 @@ static s32 igb_set_d0_lplu_state_82580(struct e1000_hw *hw, bool active)
* During driver activity, SmartSpeed should be enabled so performance is
* maintained.
**/
-s32 igb_set_d3_lplu_state_82580(struct e1000_hw *hw, bool active)
+static s32 igb_set_d3_lplu_state_82580(struct e1000_hw *hw, bool active)
{
struct e1000_phy_info *phy = &hw->phy;
s32 ret_val = 0;
@@ -877,8 +881,7 @@ s32 igb_set_d3_lplu_state_82580(struct e1000_hw *hw, bool active)
if (!active) {
data &= ~E1000_82580_PM_D3_LPLU;
- /*
- * LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used
* during Dx states where the power conservation is most
* important. During driver activity we should enable
* SmartSpeed, so performance is maintained.
@@ -964,8 +967,7 @@ static s32 igb_acquire_swfw_sync_82575(struct e1000_hw *hw, u16 mask)
if (!(swfw_sync & (fwmask | swmask)))
break;
- /*
- * Firmware currently using resource (fwmask)
+ /* Firmware currently using resource (fwmask)
* or other software thread using resource (swmask)
*/
igb_put_hw_semaphore(hw);
@@ -1065,8 +1067,7 @@ static s32 igb_check_for_link_82575(struct e1000_hw *hw)
if (hw->phy.media_type != e1000_media_type_copper) {
ret_val = igb_get_pcs_speed_and_duplex_82575(hw, &speed,
&duplex);
- /*
- * Use this flag to determine if link needs to be checked or
+ /* Use this flag to determine if link needs to be checked or
* not. If we have link clear the flag so that we do not
* continue to check for link.
*/
@@ -1135,15 +1136,13 @@ static s32 igb_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw, u16 *speed,
*speed = 0;
*duplex = 0;
- /*
- * Read the PCS Status register for link state. For non-copper mode,
+ /* Read the PCS Status register for link state. For non-copper mode,
* the status register is not accurate. The PCS status register is
* used instead.
*/
pcs = rd32(E1000_PCS_LSTAT);
- /*
- * The link up bit determines when link is up on autoneg. The sync ok
+ /* The link up bit determines when link is up on autoneg. The sync ok
* gets set once both sides sync up and agree upon link. Stable link
* can be determined by checking for both link up and link sync ok
*/
@@ -1214,8 +1213,7 @@ static s32 igb_reset_hw_82575(struct e1000_hw *hw)
u32 ctrl, icr;
s32 ret_val;
- /*
- * Prevent the PCI-E bus from sticking if there is no TLP connection
+ /* Prevent the PCI-E bus from sticking if there is no TLP connection
* on the last TLP read/write transaction when MAC is reset.
*/
ret_val = igb_disable_pcie_master(hw);
@@ -1244,8 +1242,7 @@ static s32 igb_reset_hw_82575(struct e1000_hw *hw)
ret_val = igb_get_auto_rd_done(hw);
if (ret_val) {
- /*
- * When auto config read does not complete, do not
+ /* When auto config read does not complete, do not
* return with an error. This can happen in situations
* where there is no eeprom and prevents getting link.
*/
@@ -1287,7 +1284,7 @@ static s32 igb_init_hw_82575(struct e1000_hw *hw)
/* Disabling VLAN filtering */
hw_dbg("Initializing the IEEE VLAN\n");
- if (hw->mac.type == e1000_i350)
+ if ((hw->mac.type == e1000_i350) || (hw->mac.type == e1000_i354))
igb_clear_vfta_i350(hw);
else
igb_clear_vfta(hw);
@@ -1308,8 +1305,7 @@ static s32 igb_init_hw_82575(struct e1000_hw *hw)
/* Setup link and flow control */
ret_val = igb_setup_link(hw);
- /*
- * Clear all of the statistics registers (clear on read). It is
+ /* Clear all of the statistics registers (clear on read). It is
* important that we do this after we have tried to establish link
* because the symbol error count will increment wildly if there
* is no link.
@@ -1364,6 +1360,7 @@ static s32 igb_setup_copper_link_82575(struct e1000_hw *hw)
switch (hw->phy.id) {
case I347AT4_E_PHY_ID:
case M88E1112_E_PHY_ID:
+ case M88E1545_E_PHY_ID:
case I210_I_PHY_ID:
ret_val = igb_copper_link_setup_m88_gen2(hw);
break;
@@ -1412,17 +1409,17 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
return ret_val;
- /*
- * On the 82575, SerDes loopback mode persists until it is
+ /* On the 82575, SerDes loopback mode persists until it is
* explicitly turned off or a power cycle is performed. A read to
* the register does not indicate its status. Therefore, we ensure
* loopback mode is disabled during initialization.
*/
wr32(E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
- /* power on the sfp cage if present */
+ /* power on the sfp cage if present and turn on I2C */
ctrl_ext = rd32(E1000_CTRL_EXT);
ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA;
+ ctrl_ext |= E1000_CTRL_I2C_ENA;
wr32(E1000_CTRL_EXT, ctrl_ext);
ctrl_reg = rd32(E1000_CTRL);
@@ -1466,8 +1463,7 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
pcs_autoneg = false;
}
- /*
- * non-SGMII modes only supports a speed of 1000/Full for the
+ /* non-SGMII modes only supports a speed of 1000/Full for the
* link so it is best to just force the MAC and let the pcs
* link either autoneg or be forced to 1000/Full
*/
@@ -1481,8 +1477,7 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
wr32(E1000_CTRL, ctrl_reg);
- /*
- * New SerDes mode allows for forcing speed or autonegotiating speed
+ /* New SerDes mode allows for forcing speed or autonegotiating speed
* at 1gb. Autoneg should be default set by most drivers. This is the
* mode that will be compatible with older link partners and switches.
* However, both are supported by the hardware and some drivers/tools.
@@ -1592,8 +1587,7 @@ static s32 igb_read_mac_addr_82575(struct e1000_hw *hw)
{
s32 ret_val = 0;
- /*
- * If there's an alternate MAC address place it in RAR0
+ /* If there's an alternate MAC address place it in RAR0
* so that it will override the Si installed default perm
* address.
*/
@@ -1777,8 +1771,7 @@ static s32 igb_set_pcie_completion_timeout(struct e1000_hw *hw)
if (gcr & E1000_GCR_CMPL_TMOUT_MASK)
goto out;
- /*
- * if capababilities version is type 1 we can write the
+ /* if capabilities version is type 1 we can write the
* timeout of 10ms to 200ms through the GCR register
*/
if (!(gcr & E1000_GCR_CAP_VER2)) {
@@ -1786,8 +1779,7 @@ static s32 igb_set_pcie_completion_timeout(struct e1000_hw *hw)
goto out;
}
- /*
- * for version 2 capabilities we need to write the config space
+ /* for version 2 capabilities we need to write the config space
* directly in order to set the completion timeout value for
* 16ms to 55ms
*/
@@ -1818,27 +1810,33 @@ out:
**/
void igb_vmdq_set_anti_spoofing_pf(struct e1000_hw *hw, bool enable, int pf)
{
- u32 dtxswc;
+ u32 reg_val, reg_offset;
switch (hw->mac.type) {
case e1000_82576:
+ reg_offset = E1000_DTXSWC;
+ break;
case e1000_i350:
- dtxswc = rd32(E1000_DTXSWC);
- if (enable) {
- dtxswc |= (E1000_DTXSWC_MAC_SPOOF_MASK |
- E1000_DTXSWC_VLAN_SPOOF_MASK);
- /* The PF can spoof - it has to in order to
- * support emulation mode NICs */
- dtxswc ^= (1 << pf | 1 << (pf + MAX_NUM_VFS));
- } else {
- dtxswc &= ~(E1000_DTXSWC_MAC_SPOOF_MASK |
- E1000_DTXSWC_VLAN_SPOOF_MASK);
- }
- wr32(E1000_DTXSWC, dtxswc);
+ case e1000_i354:
+ reg_offset = E1000_TXSWC;
break;
default:
- break;
+ return;
+ }
+
+ reg_val = rd32(reg_offset);
+ if (enable) {
+ reg_val |= (E1000_DTXSWC_MAC_SPOOF_MASK |
+ E1000_DTXSWC_VLAN_SPOOF_MASK);
+ /* The PF can spoof - it has to in order to
+ * support emulation mode NICs
+ */
+ reg_val ^= (1 << pf | 1 << (pf + MAX_NUM_VFS));
+ } else {
+ reg_val &= ~(E1000_DTXSWC_MAC_SPOOF_MASK |
+ E1000_DTXSWC_VLAN_SPOOF_MASK);
}
+ wr32(reg_offset, reg_val);
}
/**
@@ -1861,6 +1859,7 @@ void igb_vmdq_set_loopback_pf(struct e1000_hw *hw, bool enable)
dtxswc &= ~E1000_DTXSWC_VMDQ_LOOPBACK_EN;
wr32(E1000_DTXSWC, dtxswc);
break;
+ case e1000_i354:
case e1000_i350:
dtxswc = rd32(E1000_TXSWC);
if (enable)
@@ -1874,7 +1873,6 @@ void igb_vmdq_set_loopback_pf(struct e1000_hw *hw, bool enable)
break;
}
-
}
/**
@@ -1909,7 +1907,6 @@ static s32 igb_read_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 *data)
{
s32 ret_val;
-
ret_val = hw->phy.ops.acquire(hw);
if (ret_val)
goto out;
@@ -2011,8 +2008,7 @@ static s32 igb_reset_hw_82580(struct e1000_hw *hw)
/* Get current control state. */
ctrl = rd32(E1000_CTRL);
- /*
- * Prevent the PCI-E bus from sticking if there is no TLP connection
+ /* Prevent the PCI-E bus from sticking if there is no TLP connection
* on the last TLP read/write transaction when MAC is reset.
*/
ret_val = igb_disable_pcie_master(hw);
@@ -2047,18 +2043,13 @@ static s32 igb_reset_hw_82580(struct e1000_hw *hw)
ret_val = igb_get_auto_rd_done(hw);
if (ret_val) {
- /*
- * When auto config read does not complete, do not
+ /* When auto config read does not complete, do not
* return with an error. This can happen in situations
* where there is no eeprom and prevents getting link.
*/
hw_dbg("Auto Read Done did not complete\n");
}
- /* If EEPROM is not present, run manual init scripts */
- if ((rd32(E1000_EECD) & E1000_EECD_PRES) == 0)
- igb_reset_init_script_82575(hw);
-
/* clear global device reset status bit */
wr32(E1000_STATUS, E1000_STAT_DEV_RST_SET);
@@ -2192,7 +2183,8 @@ static s32 igb_validate_nvm_checksum_82580(struct e1000_hw *hw)
if (nvm_data & NVM_COMPATIBILITY_BIT_MASK) {
/* if checksums compatibility bit is set validate checksums
- * for all 4 ports. */
+ * for all 4 ports.
+ */
eeprom_regions_count = 4;
}
@@ -2304,6 +2296,41 @@ out:
}
/**
+ * __igb_access_emi_reg - Read/write EMI register
+ * @hw: pointer to the HW structure
+ * @addr: EMI address to program
+ * @data: pointer to value to read/write from/to the EMI address
+ * @read: boolean flag to indicate read or write
+ **/
+static s32 __igb_access_emi_reg(struct e1000_hw *hw, u16 address,
+ u16 *data, bool read)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ ret_val = hw->phy.ops.write_reg(hw, E1000_EMIADD, address);
+ if (ret_val)
+ return ret_val;
+
+ if (read)
+ ret_val = hw->phy.ops.read_reg(hw, E1000_EMIDATA, data);
+ else
+ ret_val = hw->phy.ops.write_reg(hw, E1000_EMIDATA, *data);
+
+ return ret_val;
+}
+
+/**
+ * igb_read_emi_reg - Read Extended Management Interface register
+ * @hw: pointer to the HW structure
+ * @addr: EMI address to program
+ * @data: value to be read from the EMI address
+ **/
+s32 igb_read_emi_reg(struct e1000_hw *hw, u16 addr, u16 *data)
+{
+ return __igb_access_emi_reg(hw, addr, data, true);
+}
+
+/**
* igb_set_eee_i350 - Enable/disable EEE support
* @hw: pointer to the HW structure
*
@@ -2333,7 +2360,6 @@ s32 igb_set_eee_i350(struct e1000_hw *hw)
if (eee_su & E1000_EEE_SU_LPI_CLK_STP)
hw_dbg("LPI Clock Stop Bit should not be set!\n");
-
} else {
ipcnfg &= ~(E1000_IPCNFG_EEE_1G_AN |
E1000_IPCNFG_EEE_100M_AN);
@@ -2350,6 +2376,108 @@ out:
return ret_val;
}
+/**
+ * igb_set_eee_i354 - Enable/disable EEE support
+ * @hw: pointer to the HW structure
+ *
+ * Enable/disable EEE legacy mode based on setting in dev_spec structure.
+ *
+ **/
+s32 igb_set_eee_i354(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = 0;
+ u16 phy_data;
+
+ if ((hw->phy.media_type != e1000_media_type_copper) ||
+ (phy->id != M88E1545_E_PHY_ID))
+ goto out;
+
+ if (!hw->dev_spec._82575.eee_disable) {
+ /* Switch to PHY page 18. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1545_PAGE_ADDR, 18);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.read_reg(hw, E1000_M88E1545_EEE_CTRL_1,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data |= E1000_M88E1545_EEE_CTRL_1_MS;
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1545_EEE_CTRL_1,
+ phy_data);
+ if (ret_val)
+ goto out;
+
+ /* Return the PHY to page 0. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1545_PAGE_ADDR, 0);
+ if (ret_val)
+ goto out;
+
+ /* Turn on EEE advertisement. */
+ ret_val = igb_read_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
+ E1000_EEE_ADV_DEV_I354,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data |= E1000_EEE_ADV_100_SUPPORTED |
+ E1000_EEE_ADV_1000_SUPPORTED;
+ ret_val = igb_write_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
+ E1000_EEE_ADV_DEV_I354,
+ phy_data);
+ } else {
+ /* Turn off EEE advertisement. */
+ ret_val = igb_read_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
+ E1000_EEE_ADV_DEV_I354,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data &= ~(E1000_EEE_ADV_100_SUPPORTED |
+ E1000_EEE_ADV_1000_SUPPORTED);
+ ret_val = igb_write_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
+ E1000_EEE_ADV_DEV_I354,
+ phy_data);
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_get_eee_status_i354 - Get EEE status
+ * @hw: pointer to the HW structure
+ * @status: EEE status
+ *
+ * Get EEE status by guessing based on whether Tx or Rx LPI indications have
+ * been received.
+ **/
+s32 igb_get_eee_status_i354(struct e1000_hw *hw, bool *status)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = 0;
+ u16 phy_data;
+
+ /* Check if EEE is supported on this device. */
+ if ((hw->phy.media_type != e1000_media_type_copper) ||
+ (phy->id != M88E1545_E_PHY_ID))
+ goto out;
+
+ ret_val = igb_read_xmdio_reg(hw, E1000_PCS_STATUS_ADDR_I354,
+ E1000_PCS_STATUS_DEV_I354,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ *status = phy_data & (E1000_PCS_STATUS_TX_LPI_RCVD |
+ E1000_PCS_STATUS_RX_LPI_RCVD) ? true : false;
+
+out:
+ return ret_val;
+}
+
static const u8 e1000_emc_temp_data[4] = {
E1000_EMC_INTERNAL_DATA,
E1000_EMC_DIODE1_DATA,
@@ -2363,11 +2491,12 @@ static const u8 e1000_emc_therm_limit[4] = {
E1000_EMC_DIODE3_THERM_LIMIT
};
-/* igb_get_thermal_sensor_data_generic - Gathers thermal sensor data
+/**
+ * igb_get_thermal_sensor_data_generic - Gathers thermal sensor data
* @hw: pointer to hardware structure
*
* Updates the temperatures in mac.thermal_sensor_data
- */
+ **/
s32 igb_get_thermal_sensor_data_generic(struct e1000_hw *hw)
{
s32 status = E1000_SUCCESS;
@@ -2415,12 +2544,13 @@ s32 igb_get_thermal_sensor_data_generic(struct e1000_hw *hw)
return status;
}
-/* igb_init_thermal_sensor_thresh_generic - Sets thermal sensor thresholds
+/**
+ * igb_init_thermal_sensor_thresh_generic - Sets thermal sensor thresholds
* @hw: pointer to hardware structure
*
* Sets the thermal sensor thresholds according to the NVM map
* and save off the threshold and location values into mac.thermal_sensor_data
- */
+ **/
s32 igb_init_thermal_sensor_thresh_generic(struct e1000_hw *hw)
{
s32 status = E1000_SUCCESS;
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.