diff options
Diffstat (limited to 'drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c')
| -rw-r--r-- | drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c | 187 |
1 files changed, 152 insertions, 35 deletions
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c index d81a50dc9535..2c4d327fcc2e 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c @@ -72,13 +72,13 @@ #define IXGBE_INCPER_SHIFT_82599 24 #define IXGBE_OVERFLOW_PERIOD (HZ * 30) -#define IXGBE_PTP_TX_TIMEOUT (HZ * 15) +#define IXGBE_PTP_TX_TIMEOUT (HZ) -/* half of a one second clock period, for use with PPS signal. We have to use - * this instead of something pre-defined like IXGBE_PTP_PPS_HALF_SECOND, in - * order to force at least 64bits of precision for shifting +/* We use our own definitions instead of NSEC_PER_SEC because we want to mark + * the value as a ULL to force precision when bit shifting. */ -#define IXGBE_PTP_PPS_HALF_SECOND 500000000ULL +#define NS_PER_SEC 1000000000ULL +#define NS_PER_HALF_SEC 500000000ULL /* In contrast, the X550 controller has two registers, SYSTIMEH and SYSTIMEL * which contain measurements of seconds and nanoseconds respectively. This @@ -141,23 +141,26 @@ #define MAX_TIMADJ 0x7FFFFFFF /** - * ixgbe_ptp_setup_sdp_x540 + * ixgbe_ptp_setup_sdp_X540 * @adapter: private adapter structure * * this function enables or disables the clock out feature on SDP0 for - * the X540 device. It will create a 1second periodic output that can + * the X540 device. It will create a 1 second periodic output that can * be used as the PPS (via an interrupt). * - * It calculates when the systime will be on an exact second, and then - * aligns the start of the PPS signal to that value. The shift is - * necessary because it can change based on the link speed. + * It calculates when the system time will be on an exact second, and then + * aligns the start of the PPS signal to that value. + * + * This works by using the cycle counter shift and mult values in reverse, and + * assumes that the values we're shifting will not overflow. */ -static void ixgbe_ptp_setup_sdp_x540(struct ixgbe_adapter *adapter) +static void ixgbe_ptp_setup_sdp_X540(struct ixgbe_adapter *adapter) { + struct cyclecounter *cc = &adapter->hw_cc; struct ixgbe_hw *hw = &adapter->hw; - int shift = adapter->hw_cc.shift; u32 esdp, tsauxc, clktiml, clktimh, trgttiml, trgttimh, rem; - u64 ns = 0, clock_edge = 0; + u64 ns = 0, clock_edge = 0, clock_period; + unsigned long flags; /* disable the pin first */ IXGBE_WRITE_REG(hw, IXGBE_TSAUXC, 0x0); @@ -177,26 +180,36 @@ static void ixgbe_ptp_setup_sdp_x540(struct ixgbe_adapter *adapter) /* enable the Clock Out feature on SDP0, and allow * interrupts to occur when the pin changes */ - tsauxc = IXGBE_TSAUXC_EN_CLK | - IXGBE_TSAUXC_SYNCLK | - IXGBE_TSAUXC_SDP0_INT; + tsauxc = (IXGBE_TSAUXC_EN_CLK | + IXGBE_TSAUXC_SYNCLK | + IXGBE_TSAUXC_SDP0_INT); - /* clock period (or pulse length) */ - clktiml = (u32)(IXGBE_PTP_PPS_HALF_SECOND << shift); - clktimh = (u32)((IXGBE_PTP_PPS_HALF_SECOND << shift) >> 32); - - /* Account for the cyclecounter wrap-around value by - * using the converted ns value of the current time to - * check for when the next aligned second would occur. + /* Determine the clock time period to use. This assumes that the + * cycle counter shift is small enough to avoid overflow. */ - clock_edge |= (u64)IXGBE_READ_REG(hw, IXGBE_SYSTIML); - clock_edge |= (u64)IXGBE_READ_REG(hw, IXGBE_SYSTIMH) << 32; - ns = timecounter_cyc2time(&adapter->hw_tc, clock_edge); + clock_period = div_u64((NS_PER_HALF_SEC << cc->shift), cc->mult); + clktiml = (u32)(clock_period); + clktimh = (u32)(clock_period >> 32); - div_u64_rem(ns, IXGBE_PTP_PPS_HALF_SECOND, &rem); - clock_edge += ((IXGBE_PTP_PPS_HALF_SECOND - (u64)rem) << shift); + /* Read the current clock time, and save the cycle counter value */ + spin_lock_irqsave(&adapter->tmreg_lock, flags); + ns = timecounter_read(&adapter->hw_tc); + clock_edge = adapter->hw_tc.cycle_last; + spin_unlock_irqrestore(&adapter->tmreg_lock, flags); + + /* Figure out how many seconds to add in order to round up */ + div_u64_rem(ns, NS_PER_SEC, &rem); + + /* Figure out how many nanoseconds to add to round the clock edge up + * to the next full second + */ + rem = (NS_PER_SEC - rem); - /* specify the initial clock start time */ + /* Adjust the clock edge to align with the next full second. This + * assumes that the cycle counter shift is small enough to avoid + * overflowing when shifting the remainder. + */ + clock_edge += div_u64((rem << cc->shift), cc->mult); trgttiml = (u32)clock_edge; trgttimh = (u32)(clock_edge >> 32); @@ -212,8 +225,103 @@ static void ixgbe_ptp_setup_sdp_x540(struct ixgbe_adapter *adapter) } /** + * ixgbe_ptp_setup_sdp_X550 + * @adapter: private adapter structure + * + * Enable or disable a clock output signal on SDP 0 for X550 hardware. + * + * Use the target time feature to align the output signal on the next full + * second. + * + * This works by using the cycle counter shift and mult values in reverse, and + * assumes that the values we're shifting will not overflow. + */ +static void ixgbe_ptp_setup_sdp_X550(struct ixgbe_adapter *adapter) +{ + u32 esdp, tsauxc, freqout, trgttiml, trgttimh, rem, tssdp; + struct cyclecounter *cc = &adapter->hw_cc; + struct ixgbe_hw *hw = &adapter->hw; + u64 ns = 0, clock_edge = 0; + struct timespec64 ts; + unsigned long flags; + + /* disable the pin first */ + IXGBE_WRITE_REG(hw, IXGBE_TSAUXC, 0x0); + IXGBE_WRITE_FLUSH(hw); + + if (!(adapter->flags2 & IXGBE_FLAG2_PTP_PPS_ENABLED)) + return; + + esdp = IXGBE_READ_REG(hw, IXGBE_ESDP); + + /* enable the SDP0 pin as output, and connected to the + * native function for Timesync (ClockOut) + */ + esdp |= IXGBE_ESDP_SDP0_DIR | + IXGBE_ESDP_SDP0_NATIVE; + + /* enable the Clock Out feature on SDP0, and use Target Time 0 to + * enable generation of interrupts on the clock change. + */ +#define IXGBE_TSAUXC_DIS_TS_CLEAR 0x40000000 + tsauxc = (IXGBE_TSAUXC_EN_CLK | IXGBE_TSAUXC_ST0 | + IXGBE_TSAUXC_EN_TT0 | IXGBE_TSAUXC_SDP0_INT | + IXGBE_TSAUXC_DIS_TS_CLEAR); + + tssdp = (IXGBE_TSSDP_TS_SDP0_EN | + IXGBE_TSSDP_TS_SDP0_CLK0); + + /* Determine the clock time period to use. This assumes that the + * cycle counter shift is small enough to avoid overflowing a 32bit + * value. + */ + freqout = div_u64(NS_PER_HALF_SEC << cc->shift, cc->mult); + + /* Read the current clock time, and save the cycle counter value */ + spin_lock_irqsave(&adapter->tmreg_lock, flags); + ns = timecounter_read(&adapter->hw_tc); + clock_edge = adapter->hw_tc.cycle_last; + spin_unlock_irqrestore(&adapter->tmreg_lock, flags); + + /* Figure out how far past the next second we are */ + div_u64_rem(ns, NS_PER_SEC, &rem); + + /* Figure out how many nanoseconds to add to round the clock edge up + * to the next full second + */ + rem = (NS_PER_SEC - rem); + + /* Adjust the clock edge to align with the next full second. This + * assumes that the cycle counter shift is small enough to avoid + * overflowing when shifting the remainder. + */ + clock_edge += div_u64((rem << cc->shift), cc->mult); + + /* X550 hardware stores the time in 32bits of 'billions of cycles' and + * 32bits of 'cycles'. There's no guarantee that cycles represents + * nanoseconds. However, we can use the math from a timespec64 to + * convert into the hardware representation. + * + * See ixgbe_ptp_read_X550() for more details. + */ + ts = ns_to_timespec64(clock_edge); + trgttiml = (u32)ts.tv_nsec; + trgttimh = (u32)ts.tv_sec; + + IXGBE_WRITE_REG(hw, IXGBE_FREQOUT0, freqout); + IXGBE_WRITE_REG(hw, IXGBE_TRGTTIML0, trgttiml); + IXGBE_WRITE_REG(hw, IXGBE_TRGTTIMH0, trgttimh); + + IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); + IXGBE_WRITE_REG(hw, IXGBE_TSSDP, tssdp); + IXGBE_WRITE_REG(hw, IXGBE_TSAUXC, tsauxc); + + IXGBE_WRITE_FLUSH(hw); +} + +/** * ixgbe_ptp_read_X550 - read cycle counter value - * @hw_cc: cyclecounter structure + * @cc: cyclecounter structure * * This function reads SYSTIME registers. It is called by the cyclecounter * structure to convert from internal representation into nanoseconds. We need @@ -221,10 +329,10 @@ static void ixgbe_ptp_setup_sdp_x540(struct ixgbe_adapter *adapter) * result of SYSTIME is 32bits of "billions of cycles" and 32 bits of * "cycles", rather than seconds and nanoseconds. */ -static u64 ixgbe_ptp_read_X550(const struct cyclecounter *hw_cc) +static u64 ixgbe_ptp_read_X550(const struct cyclecounter *cc) { struct ixgbe_adapter *adapter = - container_of(hw_cc, struct ixgbe_adapter, hw_cc); + container_of(cc, struct ixgbe_adapter, hw_cc); struct ixgbe_hw *hw = &adapter->hw; struct timespec64 ts; @@ -838,6 +946,15 @@ void ixgbe_ptp_rx_rgtstamp(struct ixgbe_q_vector *q_vector, ixgbe_ptp_convert_to_hwtstamp(adapter, skb_hwtstamps(skb), regval); } +/** + * ixgbe_ptp_get_ts_config - get current hardware timestamping configuration + * @adapter: pointer to adapter structure + * @ifr: ioctl data + * + * This function returns the current timestamping settings. Rather than + * attempt to deconstruct registers to fill in the values, simply keep a copy + * of the old settings around, and return a copy when requested. + */ int ixgbe_ptp_get_ts_config(struct ixgbe_adapter *adapter, struct ifreq *ifr) { struct hwtstamp_config *config = &adapter->tstamp_config; @@ -1253,7 +1370,7 @@ static long ixgbe_ptp_create_clock(struct ixgbe_adapter *adapter) adapter->ptp_caps.gettimex64 = ixgbe_ptp_gettimex; adapter->ptp_caps.settime64 = ixgbe_ptp_settime; adapter->ptp_caps.enable = ixgbe_ptp_feature_enable; - adapter->ptp_setup_sdp = ixgbe_ptp_setup_sdp_x540; + adapter->ptp_setup_sdp = ixgbe_ptp_setup_sdp_X540; break; case ixgbe_mac_82599EB: snprintf(adapter->ptp_caps.name, @@ -1280,13 +1397,13 @@ static long ixgbe_ptp_create_clock(struct ixgbe_adapter *adapter) adapter->ptp_caps.n_alarm = 0; adapter->ptp_caps.n_ext_ts = 0; adapter->ptp_caps.n_per_out = 0; - adapter->ptp_caps.pps = 0; + adapter->ptp_caps.pps = 1; adapter->ptp_caps.adjfreq = ixgbe_ptp_adjfreq_X550; adapter->ptp_caps.adjtime = ixgbe_ptp_adjtime; adapter->ptp_caps.gettimex64 = ixgbe_ptp_gettimex; adapter->ptp_caps.settime64 = ixgbe_ptp_settime; adapter->ptp_caps.enable = ixgbe_ptp_feature_enable; - adapter->ptp_setup_sdp = NULL; + adapter->ptp_setup_sdp = ixgbe_ptp_setup_sdp_X550; break; default: adapter->ptp_clock = NULL; |