diff options
Diffstat (limited to 'drivers/net/ethernet/sfc/falcon/txc43128_phy.c')
| -rw-r--r-- | drivers/net/ethernet/sfc/falcon/txc43128_phy.c | 560 |
1 files changed, 560 insertions, 0 deletions
diff --git a/drivers/net/ethernet/sfc/falcon/txc43128_phy.c b/drivers/net/ethernet/sfc/falcon/txc43128_phy.c new file mode 100644 index 000000000000..18421f5e880f --- /dev/null +++ b/drivers/net/ethernet/sfc/falcon/txc43128_phy.c @@ -0,0 +1,560 @@ +/**************************************************************************** + * Driver for Solarflare network controllers and boards + * Copyright 2006-2011 Solarflare Communications Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation, incorporated herein by reference. + */ + +/* + * Driver for Transwitch/Mysticom CX4 retimer + * see www.transwitch.com, part is TXC-43128 + */ + +#include <linux/delay.h> +#include <linux/slab.h> +#include "efx.h" +#include "mdio_10g.h" +#include "phy.h" +#include "nic.h" + +/* We expect these MMDs to be in the package */ +#define TXC_REQUIRED_DEVS (MDIO_DEVS_PCS | \ + MDIO_DEVS_PMAPMD | \ + MDIO_DEVS_PHYXS) + +#define TXC_LOOPBACKS ((1 << LOOPBACK_PCS) | \ + (1 << LOOPBACK_PMAPMD) | \ + (1 << LOOPBACK_PHYXS_WS)) + +/************************************************************************** + * + * Compile-time config + * + ************************************************************************** + */ +#define TXCNAME "TXC43128" +/* Total length of time we'll wait for the PHY to come out of reset (ms) */ +#define TXC_MAX_RESET_TIME 500 +/* Interval between checks (ms) */ +#define TXC_RESET_WAIT 10 +/* How long to run BIST (us) */ +#define TXC_BIST_DURATION 50 + +/************************************************************************** + * + * Register definitions + * + ************************************************************************** + */ + +/* Command register */ +#define TXC_GLRGS_GLCMD 0xc004 +/* Useful bits in command register */ +/* Lane power-down */ +#define TXC_GLCMD_L01PD_LBN 5 +#define TXC_GLCMD_L23PD_LBN 6 +/* Limited SW reset: preserves configuration but + * initiates a logic reset. Self-clearing */ +#define TXC_GLCMD_LMTSWRST_LBN 14 + +/* Signal Quality Control */ +#define TXC_GLRGS_GSGQLCTL 0xc01a +/* Enable bit */ +#define TXC_GSGQLCT_SGQLEN_LBN 15 +/* Lane selection */ +#define TXC_GSGQLCT_LNSL_LBN 13 +#define TXC_GSGQLCT_LNSL_WIDTH 2 + +/* Analog TX control */ +#define TXC_ALRGS_ATXCTL 0xc040 +/* Lane power-down */ +#define TXC_ATXCTL_TXPD3_LBN 15 +#define TXC_ATXCTL_TXPD2_LBN 14 +#define TXC_ATXCTL_TXPD1_LBN 13 +#define TXC_ATXCTL_TXPD0_LBN 12 + +/* Amplitude on lanes 0, 1 */ +#define TXC_ALRGS_ATXAMP0 0xc041 +/* Amplitude on lanes 2, 3 */ +#define TXC_ALRGS_ATXAMP1 0xc042 +/* Bit position of value for lane 0 (or 2) */ +#define TXC_ATXAMP_LANE02_LBN 3 +/* Bit position of value for lane 1 (or 3) */ +#define TXC_ATXAMP_LANE13_LBN 11 + +#define TXC_ATXAMP_1280_mV 0 +#define TXC_ATXAMP_1200_mV 8 +#define TXC_ATXAMP_1120_mV 12 +#define TXC_ATXAMP_1060_mV 14 +#define TXC_ATXAMP_0820_mV 25 +#define TXC_ATXAMP_0720_mV 26 +#define TXC_ATXAMP_0580_mV 27 +#define TXC_ATXAMP_0440_mV 28 + +#define TXC_ATXAMP_0820_BOTH \ + ((TXC_ATXAMP_0820_mV << TXC_ATXAMP_LANE02_LBN) \ + | (TXC_ATXAMP_0820_mV << TXC_ATXAMP_LANE13_LBN)) + +#define TXC_ATXAMP_DEFAULT 0x6060 /* From databook */ + +/* Preemphasis on lanes 0, 1 */ +#define TXC_ALRGS_ATXPRE0 0xc043 +/* Preemphasis on lanes 2, 3 */ +#define TXC_ALRGS_ATXPRE1 0xc044 + +#define TXC_ATXPRE_NONE 0 +#define TXC_ATXPRE_DEFAULT 0x1010 /* From databook */ + +#define TXC_ALRGS_ARXCTL 0xc045 +/* Lane power-down */ +#define TXC_ARXCTL_RXPD3_LBN 15 +#define TXC_ARXCTL_RXPD2_LBN 14 +#define TXC_ARXCTL_RXPD1_LBN 13 +#define TXC_ARXCTL_RXPD0_LBN 12 + +/* Main control */ +#define TXC_MRGS_CTL 0xc340 +/* Bits in main control */ +#define TXC_MCTL_RESET_LBN 15 /* Self clear */ +#define TXC_MCTL_TXLED_LBN 14 /* 1 to show align status */ +#define TXC_MCTL_RXLED_LBN 13 /* 1 to show align status */ + +/* GPIO output */ +#define TXC_GPIO_OUTPUT 0xc346 +#define TXC_GPIO_DIR 0xc348 + +/* Vendor-specific BIST registers */ +#define TXC_BIST_CTL 0xc280 +#define TXC_BIST_TXFRMCNT 0xc281 +#define TXC_BIST_RX0FRMCNT 0xc282 +#define TXC_BIST_RX1FRMCNT 0xc283 +#define TXC_BIST_RX2FRMCNT 0xc284 +#define TXC_BIST_RX3FRMCNT 0xc285 +#define TXC_BIST_RX0ERRCNT 0xc286 +#define TXC_BIST_RX1ERRCNT 0xc287 +#define TXC_BIST_RX2ERRCNT 0xc288 +#define TXC_BIST_RX3ERRCNT 0xc289 + +/* BIST type (controls bit patter in test) */ +#define TXC_BIST_CTRL_TYPE_LBN 10 +#define TXC_BIST_CTRL_TYPE_TSD 0 /* TranSwitch Deterministic */ +#define TXC_BIST_CTRL_TYPE_CRP 1 /* CRPAT standard */ +#define TXC_BIST_CTRL_TYPE_CJP 2 /* CJPAT standard */ +#define TXC_BIST_CTRL_TYPE_TSR 3 /* TranSwitch pseudo-random */ +/* Set this to 1 for 10 bit and 0 for 8 bit */ +#define TXC_BIST_CTRL_B10EN_LBN 12 +/* Enable BIST (write 0 to disable) */ +#define TXC_BIST_CTRL_ENAB_LBN 13 +/* Stop BIST (self-clears when stop complete) */ +#define TXC_BIST_CTRL_STOP_LBN 14 +/* Start BIST (cleared by writing 1 to STOP) */ +#define TXC_BIST_CTRL_STRT_LBN 15 + +/* Mt. Diablo test configuration */ +#define TXC_MTDIABLO_CTRL 0xc34f +#define TXC_MTDIABLO_CTRL_PMA_LOOP_LBN 10 + +struct txc43128_data { + unsigned long bug10934_timer; + enum ef4_phy_mode phy_mode; + enum ef4_loopback_mode loopback_mode; +}; + +/* The PHY sometimes needs a reset to bring the link back up. So long as + * it reports link down, we reset it every 5 seconds. + */ +#define BUG10934_RESET_INTERVAL (5 * HZ) + +/* Perform a reset that doesn't clear configuration changes */ +static void txc_reset_logic(struct ef4_nic *efx); + +/* Set the output value of a gpio */ +void falcon_txc_set_gpio_val(struct ef4_nic *efx, int pin, int on) +{ + ef4_mdio_set_flag(efx, MDIO_MMD_PHYXS, TXC_GPIO_OUTPUT, 1 << pin, on); +} + +/* Set up the GPIO direction register */ +void falcon_txc_set_gpio_dir(struct ef4_nic *efx, int pin, int dir) +{ + ef4_mdio_set_flag(efx, MDIO_MMD_PHYXS, TXC_GPIO_DIR, 1 << pin, dir); +} + +/* Reset the PMA/PMD MMD. The documentation is explicit that this does a + * global reset (it's less clear what reset of other MMDs does).*/ +static int txc_reset_phy(struct ef4_nic *efx) +{ + int rc = ef4_mdio_reset_mmd(efx, MDIO_MMD_PMAPMD, + TXC_MAX_RESET_TIME / TXC_RESET_WAIT, + TXC_RESET_WAIT); + if (rc < 0) + goto fail; + + /* Check that all the MMDs we expect are present and responding. */ + rc = ef4_mdio_check_mmds(efx, TXC_REQUIRED_DEVS); + if (rc < 0) + goto fail; + + return 0; + +fail: + netif_err(efx, hw, efx->net_dev, TXCNAME ": reset timed out!\n"); + return rc; +} + +/* Run a single BIST on one MMD */ +static int txc_bist_one(struct ef4_nic *efx, int mmd, int test) +{ + int ctrl, bctl; + int lane; + int rc = 0; + + /* Set PMA to test into loopback using Mt Diablo reg as per app note */ + ctrl = ef4_mdio_read(efx, MDIO_MMD_PCS, TXC_MTDIABLO_CTRL); + ctrl |= (1 << TXC_MTDIABLO_CTRL_PMA_LOOP_LBN); + ef4_mdio_write(efx, MDIO_MMD_PCS, TXC_MTDIABLO_CTRL, ctrl); + + /* The BIST app. note lists these as 3 distinct steps. */ + /* Set the BIST type */ + bctl = (test << TXC_BIST_CTRL_TYPE_LBN); + ef4_mdio_write(efx, mmd, TXC_BIST_CTL, bctl); + + /* Set the BSTEN bit in the BIST Control register to enable */ + bctl |= (1 << TXC_BIST_CTRL_ENAB_LBN); + ef4_mdio_write(efx, mmd, TXC_BIST_CTL, bctl); + + /* Set the BSTRT bit in the BIST Control register */ + ef4_mdio_write(efx, mmd, TXC_BIST_CTL, + bctl | (1 << TXC_BIST_CTRL_STRT_LBN)); + + /* Wait. */ + udelay(TXC_BIST_DURATION); + + /* Set the BSTOP bit in the BIST Control register */ + bctl |= (1 << TXC_BIST_CTRL_STOP_LBN); + ef4_mdio_write(efx, mmd, TXC_BIST_CTL, bctl); + + /* The STOP bit should go off when things have stopped */ + while (bctl & (1 << TXC_BIST_CTRL_STOP_LBN)) + bctl = ef4_mdio_read(efx, mmd, TXC_BIST_CTL); + + /* Check all the error counts are 0 and all the frame counts are + non-zero */ + for (lane = 0; lane < 4; lane++) { + int count = ef4_mdio_read(efx, mmd, TXC_BIST_RX0ERRCNT + lane); + if (count != 0) { + netif_err(efx, hw, efx->net_dev, TXCNAME": BIST error. " + "Lane %d had %d errs\n", lane, count); + rc = -EIO; + } + count = ef4_mdio_read(efx, mmd, TXC_BIST_RX0FRMCNT + lane); + if (count == 0) { + netif_err(efx, hw, efx->net_dev, TXCNAME": BIST error. " + "Lane %d got 0 frames\n", lane); + rc = -EIO; + } + } + + if (rc == 0) + netif_info(efx, hw, efx->net_dev, TXCNAME": BIST pass\n"); + + /* Disable BIST */ + ef4_mdio_write(efx, mmd, TXC_BIST_CTL, 0); + + /* Turn off loopback */ + ctrl &= ~(1 << TXC_MTDIABLO_CTRL_PMA_LOOP_LBN); + ef4_mdio_write(efx, MDIO_MMD_PCS, TXC_MTDIABLO_CTRL, ctrl); + + return rc; +} + +static int txc_bist(struct ef4_nic *efx) +{ + return txc_bist_one(efx, MDIO_MMD_PCS, TXC_BIST_CTRL_TYPE_TSD); +} + +/* Push the non-configurable defaults into the PHY. This must be + * done after every full reset */ +static void txc_apply_defaults(struct ef4_nic *efx) +{ + int mctrl; + + /* Turn amplitude down and preemphasis off on the host side + * (PHY<->MAC) as this is believed less likely to upset Falcon + * and no adverse effects have been noted. It probably also + * saves a picowatt or two */ + + /* Turn off preemphasis */ + ef4_mdio_write(efx, MDIO_MMD_PHYXS, TXC_ALRGS_ATXPRE0, TXC_ATXPRE_NONE); + ef4_mdio_write(efx, MDIO_MMD_PHYXS, TXC_ALRGS_ATXPRE1, TXC_ATXPRE_NONE); + + /* Turn down the amplitude */ + ef4_mdio_write(efx, MDIO_MMD_PHYXS, + TXC_ALRGS_ATXAMP0, TXC_ATXAMP_0820_BOTH); + ef4_mdio_write(efx, MDIO_MMD_PHYXS, + TXC_ALRGS_ATXAMP1, TXC_ATXAMP_0820_BOTH); + + /* Set the line side amplitude and preemphasis to the databook + * defaults as an erratum causes them to be 0 on at least some + * PHY rev.s */ + ef4_mdio_write(efx, MDIO_MMD_PMAPMD, + TXC_ALRGS_ATXPRE0, TXC_ATXPRE_DEFAULT); + ef4_mdio_write(efx, MDIO_MMD_PMAPMD, + TXC_ALRGS_ATXPRE1, TXC_ATXPRE_DEFAULT); + ef4_mdio_write(efx, MDIO_MMD_PMAPMD, + TXC_ALRGS_ATXAMP0, TXC_ATXAMP_DEFAULT); + ef4_mdio_write(efx, MDIO_MMD_PMAPMD, + TXC_ALRGS_ATXAMP1, TXC_ATXAMP_DEFAULT); + + /* Set up the LEDs */ + mctrl = ef4_mdio_read(efx, MDIO_MMD_PHYXS, TXC_MRGS_CTL); + + /* Set the Green and Red LEDs to their default modes */ + mctrl &= ~((1 << TXC_MCTL_TXLED_LBN) | (1 << TXC_MCTL_RXLED_LBN)); + ef4_mdio_write(efx, MDIO_MMD_PHYXS, TXC_MRGS_CTL, mctrl); + + /* Databook recommends doing this after configuration changes */ + txc_reset_logic(efx); + + falcon_board(efx)->type->init_phy(efx); +} + +static int txc43128_phy_probe(struct ef4_nic *efx) +{ + struct txc43128_data *phy_data; + + /* Allocate phy private storage */ + phy_data = kzalloc(sizeof(*phy_data), GFP_KERNEL); + if (!phy_data) + return -ENOMEM; + efx->phy_data = phy_data; + phy_data->phy_mode = efx->phy_mode; + + efx->mdio.mmds = TXC_REQUIRED_DEVS; + efx->mdio.mode_support = MDIO_SUPPORTS_C45 | MDIO_EMULATE_C22; + + efx->loopback_modes = TXC_LOOPBACKS | FALCON_XMAC_LOOPBACKS; + + return 0; +} + +/* Initialisation entry point for this PHY driver */ +static int txc43128_phy_init(struct ef4_nic *efx) +{ + int rc; + + rc = txc_reset_phy(efx); + if (rc < 0) + return rc; + + rc = txc_bist(efx); + if (rc < 0) + return rc; + + txc_apply_defaults(efx); + + return 0; +} + +/* Set the lane power down state in the global registers */ +static void txc_glrgs_lane_power(struct ef4_nic *efx, int mmd) +{ + int pd = (1 << TXC_GLCMD_L01PD_LBN) | (1 << TXC_GLCMD_L23PD_LBN); + int ctl = ef4_mdio_read(efx, mmd, TXC_GLRGS_GLCMD); + + if (!(efx->phy_mode & PHY_MODE_LOW_POWER)) + ctl &= ~pd; + else + ctl |= pd; + + ef4_mdio_write(efx, mmd, TXC_GLRGS_GLCMD, ctl); +} + +/* Set the lane power down state in the analog control registers */ +static void txc_analog_lane_power(struct ef4_nic *efx, int mmd) +{ + int txpd = (1 << TXC_ATXCTL_TXPD3_LBN) | (1 << TXC_ATXCTL_TXPD2_LBN) + | (1 << TXC_ATXCTL_TXPD1_LBN) | (1 << TXC_ATXCTL_TXPD0_LBN); + int rxpd = (1 << TXC_ARXCTL_RXPD3_LBN) | (1 << TXC_ARXCTL_RXPD2_LBN) + | (1 << TXC_ARXCTL_RXPD1_LBN) | (1 << TXC_ARXCTL_RXPD0_LBN); + int txctl = ef4_mdio_read(efx, mmd, TXC_ALRGS_ATXCTL); + int rxctl = ef4_mdio_read(efx, mmd, TXC_ALRGS_ARXCTL); + + if (!(efx->phy_mode & PHY_MODE_LOW_POWER)) { + txctl &= ~txpd; + rxctl &= ~rxpd; + } else { + txctl |= txpd; + rxctl |= rxpd; + } + + ef4_mdio_write(efx, mmd, TXC_ALRGS_ATXCTL, txctl); + ef4_mdio_write(efx, mmd, TXC_ALRGS_ARXCTL, rxctl); +} + +static void txc_set_power(struct ef4_nic *efx) +{ + /* According to the data book, all the MMDs can do low power */ + ef4_mdio_set_mmds_lpower(efx, + !!(efx->phy_mode & PHY_MODE_LOW_POWER), + TXC_REQUIRED_DEVS); + + /* Global register bank is in PCS, PHY XS. These control the host + * side and line side settings respectively. */ + txc_glrgs_lane_power(efx, MDIO_MMD_PCS); + txc_glrgs_lane_power(efx, MDIO_MMD_PHYXS); + + /* Analog register bank in PMA/PMD, PHY XS */ + txc_analog_lane_power(efx, MDIO_MMD_PMAPMD); + txc_analog_lane_power(efx, MDIO_MMD_PHYXS); +} + +static void txc_reset_logic_mmd(struct ef4_nic *efx, int mmd) +{ + int val = ef4_mdio_read(efx, mmd, TXC_GLRGS_GLCMD); + int tries = 50; + + val |= (1 << TXC_GLCMD_LMTSWRST_LBN); + ef4_mdio_write(efx, mmd, TXC_GLRGS_GLCMD, val); + while (--tries) { + val = ef4_mdio_read(efx, mmd, TXC_GLRGS_GLCMD); + if (!(val & (1 << TXC_GLCMD_LMTSWRST_LBN))) + break; + udelay(1); + } + if (!tries) + netif_info(efx, hw, efx->net_dev, + TXCNAME " Logic reset timed out!\n"); +} + +/* Perform a logic reset. This preserves the configuration registers + * and is needed for some configuration changes to take effect */ +static void txc_reset_logic(struct ef4_nic *efx) +{ + /* The data sheet claims we can do the logic reset on either the + * PCS or the PHYXS and the result is a reset of both host- and + * line-side logic. */ + txc_reset_logic_mmd(efx, MDIO_MMD_PCS); +} + +static bool txc43128_phy_read_link(struct ef4_nic *efx) +{ + return ef4_mdio_links_ok(efx, TXC_REQUIRED_DEVS); +} + +static int txc43128_phy_reconfigure(struct ef4_nic *efx) +{ + struct txc43128_data *phy_data = efx->phy_data; + enum ef4_phy_mode mode_change = efx->phy_mode ^ phy_data->phy_mode; + bool loop_change = LOOPBACK_CHANGED(phy_data, efx, TXC_LOOPBACKS); + + if (efx->phy_mode & mode_change & PHY_MODE_TX_DISABLED) { + txc_reset_phy(efx); + txc_apply_defaults(efx); + falcon_reset_xaui(efx); + mode_change &= ~PHY_MODE_TX_DISABLED; + } + + ef4_mdio_transmit_disable(efx); + ef4_mdio_phy_reconfigure(efx); + if (mode_change & PHY_MODE_LOW_POWER) + txc_set_power(efx); + + /* The data sheet claims this is required after every reconfiguration + * (note at end of 7.1), but we mustn't do it when nothing changes as + * it glitches the link, and reconfigure gets called on link change, + * so we get an IRQ storm on link up. */ + if (loop_change || mode_change) + txc_reset_logic(efx); + + phy_data->phy_mode = efx->phy_mode; + phy_data->loopback_mode = efx->loopback_mode; + + return 0; +} + +static void txc43128_phy_fini(struct ef4_nic *efx) +{ + /* Disable link events */ + ef4_mdio_write(efx, MDIO_MMD_PMAPMD, MDIO_PMA_LASI_CTRL, 0); +} + +static void txc43128_phy_remove(struct ef4_nic *efx) +{ + kfree(efx->phy_data); + efx->phy_data = NULL; +} + +/* Periodic callback: this exists mainly to poll link status as we + * don't use LASI interrupts */ +static bool txc43128_phy_poll(struct ef4_nic *efx) +{ + struct txc43128_data *data = efx->phy_data; + bool was_up = efx->link_state.up; + + efx->link_state.up = txc43128_phy_read_link(efx); + efx->link_state.speed = 10000; + efx->link_state.fd = true; + efx->link_state.fc = efx->wanted_fc; + + if (efx->link_state.up || (efx->loopback_mode != LOOPBACK_NONE)) { + data->bug10934_timer = jiffies; + } else { + if (time_after_eq(jiffies, (data->bug10934_timer + + BUG10934_RESET_INTERVAL))) { + data->bug10934_timer = jiffies; + txc_reset_logic(efx); + } + } + + return efx->link_state.up != was_up; +} + +static const char *const txc43128_test_names[] = { + "bist" +}; + +static const char *txc43128_test_name(struct ef4_nic *efx, unsigned int index) +{ + if (index < ARRAY_SIZE(txc43128_test_names)) + return txc43128_test_names[index]; + return NULL; +} + +static int txc43128_run_tests(struct ef4_nic *efx, int *results, unsigned flags) +{ + int rc; + + if (!(flags & ETH_TEST_FL_OFFLINE)) + return 0; + + rc = txc_reset_phy(efx); + if (rc < 0) + return rc; + + rc = txc_bist(efx); + txc_apply_defaults(efx); + results[0] = rc ? -1 : 1; + return rc; +} + +static void txc43128_get_settings(struct ef4_nic *efx, struct ethtool_cmd *ecmd) +{ + mdio45_ethtool_gset(&efx->mdio, ecmd); +} + +const struct ef4_phy_operations falcon_txc_phy_ops = { + .probe = txc43128_phy_probe, + .init = txc43128_phy_init, + .reconfigure = txc43128_phy_reconfigure, + .poll = txc43128_phy_poll, + .fini = txc43128_phy_fini, + .remove = txc43128_phy_remove, + .get_settings = txc43128_get_settings, + .set_settings = ef4_mdio_set_settings, + .test_alive = ef4_mdio_test_alive, + .run_tests = txc43128_run_tests, + .test_name = txc43128_test_name, +}; |