1 files changed, 241 insertions, 117 deletions

diff --git a/drivers/net/ieee802154/at86rf230.c b/drivers/net/ieee802154/at86rf230.c
index 7b051eacb7f1..38026650c038 100644
--- a/drivers/net/ieee802154/at86rf230.c
+++ b/drivers/net/ieee802154/at86rf230.c
@@ -19,11 +19,12 @@
  */
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/hrtimer.h>
+#include <linux/jiffies.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/gpio.h>
 #include <linux/delay.h>
-#include <linux/spinlock.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/at86rf230.h>
 #include <linux/regmap.h>
@@ -46,19 +47,27 @@ struct at86rf2xx_chip_data {
 	u16 t_off_to_tx_on;
 	u16 t_frame;
 	u16 t_p_ack;
-	/* completion timeout for tx in msecs */
-	u16 t_tx_timeout;
 	int rssi_base_val;
 
 	int (*set_channel)(struct at86rf230_local *, u8, u8);
 	int (*get_desense_steps)(struct at86rf230_local *, s32);
 };
 
-#define AT86RF2XX_MAX_BUF (127 + 3)
+#define AT86RF2XX_MAX_BUF		(127 + 3)
+/* tx retries to access the TX_ON state
+ * if it's above then force change will be started.
+ *
+ * We assume the max_frame_retries (7) value of 802.15.4 here.
+ */
+#define AT86RF2XX_MAX_TX_RETRIES	7
+/* We use the recommended 5 minutes timeout to recalibrate */
+#define AT86RF2XX_CAL_LOOP_TIMEOUT	(5 * 60 * HZ)
 
 struct at86rf230_state_change {
 	struct at86rf230_local *lp;
+	int irq;
 
+	struct hrtimer timer;
 	struct spi_message msg;
 	struct spi_transfer trx;
 	u8 buf[AT86RF2XX_MAX_BUF];
@@ -83,10 +92,10 @@ struct at86rf230_local {
 	struct at86rf230_state_change irq;
 
 	bool tx_aret;
+	unsigned long cal_timeout;
 	s8 max_frame_retries;
 	bool is_tx;
-	/* spinlock for is_tx protection */
-	spinlock_t lock;
+	u8 tx_retry;
 	struct sk_buff *tx_skb;
 	struct at86rf230_state_change tx;
 };
@@ -313,7 +322,7 @@ at86rf230_read_subreg(struct at86rf230_local *lp,
 	int rc;
 
 	rc = __at86rf230_read(lp, addr, data);
-	if (rc > 0)
+	if (!rc)
 		*data = (*data & mask) >> shift;
 
 	return rc;
@@ -409,6 +418,8 @@ at86rf230_reg_volatile(struct device *dev, unsigned int reg)
 	case RG_PHY_ED_LEVEL:
 	case RG_IRQ_STATUS:
 	case RG_VREG_CTRL:
+	case RG_PLL_CF:
+	case RG_PLL_DCU:
 		return true;
 	default:
 		return false;
@@ -446,6 +457,7 @@ at86rf230_async_error_recover(void *context)
 	struct at86rf230_state_change *ctx = context;
 	struct at86rf230_local *lp = ctx->lp;
 
+	lp->is_tx = 0;
 	at86rf230_async_state_change(lp, ctx, STATE_RX_AACK_ON, NULL, false);
 	ieee802154_wake_queue(lp->hw);
 }
@@ -472,18 +484,25 @@ at86rf230_async_read_reg(struct at86rf230_local *lp, const u8 reg,
 	u8 *tx_buf = ctx->buf;
 
 	tx_buf[0] = (reg & CMD_REG_MASK) | CMD_REG;
-	ctx->trx.len = 2;
 	ctx->msg.complete = complete;
 	ctx->irq_enable = irq_enable;
 	rc = spi_async(lp->spi, &ctx->msg);
 	if (rc) {
 		if (irq_enable)
-			enable_irq(lp->spi->irq);
+			enable_irq(ctx->irq);
 
 		at86rf230_async_error(lp, ctx, rc);
 	}
 }
 
+static inline u8 at86rf230_state_to_force(u8 state)
+{
+	if (state == STATE_TX_ON)
+		return STATE_FORCE_TX_ON;
+	else
+		return STATE_FORCE_TRX_OFF;
+}
+
 static void
 at86rf230_async_state_assert(void *context)
 {
@@ -514,10 +533,21 @@ at86rf230_async_state_assert(void *context)
 			 * in STATE_BUSY_RX_AACK, we run a force state change
 			 * to STATE_TX_ON. This is a timeout handling, if the
 			 * transceiver stucks in STATE_BUSY_RX_AACK.
+			 *
+			 * Additional we do several retries to try to get into
+			 * TX_ON state without forcing. If the retries are
+			 * higher or equal than AT86RF2XX_MAX_TX_RETRIES we
+			 * will do a force change.
 			 */
-			if (ctx->to_state == STATE_TX_ON) {
-				at86rf230_async_state_change(lp, ctx,
-							     STATE_FORCE_TX_ON,
+			if (ctx->to_state == STATE_TX_ON ||
+			    ctx->to_state == STATE_TRX_OFF) {
+				u8 state = ctx->to_state;
+
+				if (lp->tx_retry >= AT86RF2XX_MAX_TX_RETRIES)
+					state = at86rf230_state_to_force(state);
+				lp->tx_retry++;
+
+				at86rf230_async_state_change(lp, ctx, state,
 							     ctx->complete,
 							     ctx->irq_enable);
 				return;
@@ -533,6 +563,19 @@ done:
 		ctx->complete(context);
 }
 
+static enum hrtimer_restart at86rf230_async_state_timer(struct hrtimer *timer)
+{
+	struct at86rf230_state_change *ctx =
+		container_of(timer, struct at86rf230_state_change, timer);
+	struct at86rf230_local *lp = ctx->lp;
+
+	at86rf230_async_read_reg(lp, RG_TRX_STATUS, ctx,
+				 at86rf230_async_state_assert,
+				 ctx->irq_enable);
+
+	return HRTIMER_NORESTART;
+}
+
 /* Do state change timing delay. */
 static void
 at86rf230_async_state_delay(void *context)
@@ -541,6 +584,7 @@ at86rf230_async_state_delay(void *context)
 	struct at86rf230_local *lp = ctx->lp;
 	struct at86rf2xx_chip_data *c = lp->data;
 	bool force = false;
+	ktime_t tim;
 
 	/* The force state changes are will show as normal states in the
 	 * state status subregister. We change the to_state to the
@@ -564,11 +608,15 @@ at86rf230_async_state_delay(void *context)
 	case STATE_TRX_OFF:
 		switch (ctx->to_state) {
 		case STATE_RX_AACK_ON:
-			usleep_range(c->t_off_to_aack, c->t_off_to_aack + 10);
+			tim = ktime_set(0, c->t_off_to_aack * NSEC_PER_USEC);
 			goto change;
 		case STATE_TX_ON:
-			usleep_range(c->t_off_to_tx_on,
-				     c->t_off_to_tx_on + 10);
+			tim = ktime_set(0, c->t_off_to_tx_on * NSEC_PER_USEC);
+			/* state change from TRX_OFF to TX_ON to do a
+			 * calibration, we need to reset the timeout for the
+			 * next one.
+			 */
+			lp->cal_timeout = jiffies + AT86RF2XX_CAL_LOOP_TIMEOUT;
 			goto change;
 		default:
 			break;
@@ -576,14 +624,15 @@ at86rf230_async_state_delay(void *context)
 		break;
 	case STATE_BUSY_RX_AACK:
 		switch (ctx->to_state) {
+		case STATE_TRX_OFF:
 		case STATE_TX_ON:
 			/* Wait for worst case receiving time if we
 			 * didn't make a force change from BUSY_RX_AACK
-			 * to TX_ON.
+			 * to TX_ON or TRX_OFF.
 			 */
 			if (!force) {
-				usleep_range(c->t_frame + c->t_p_ack,
-					     c->t_frame + c->t_p_ack + 1000);
+				tim = ktime_set(0, (c->t_frame + c->t_p_ack) *
+						   NSEC_PER_USEC);
 				goto change;
 			}
 			break;
@@ -595,7 +644,7 @@ at86rf230_async_state_delay(void *context)
 	case STATE_P_ON:
 		switch (ctx->to_state) {
 		case STATE_TRX_OFF:
-			usleep_range(c->t_reset_to_off, c->t_reset_to_off + 10);
+			tim = ktime_set(0, c->t_reset_to_off * NSEC_PER_USEC);
 			goto change;
 		default:
 			break;
@@ -606,12 +655,10 @@ at86rf230_async_state_delay(void *context)
 	}
 
 	/* Default delay is 1us in the most cases */
-	udelay(1);
+	tim = ktime_set(0, NSEC_PER_USEC);
 
 change:
-	at86rf230_async_read_reg(lp, RG_TRX_STATUS, ctx,
-				 at86rf230_async_state_assert,
-				 ctx->irq_enable);
+	hrtimer_start(&ctx->timer, tim, HRTIMER_MODE_REL);
 }
 
 static void
@@ -647,12 +694,11 @@ at86rf230_async_state_change_start(void *context)
 	 */
 	buf[0] = (RG_TRX_STATE & CMD_REG_MASK) | CMD_REG | CMD_WRITE;
 	buf[1] = ctx->to_state;
-	ctx->trx.len = 2;
 	ctx->msg.complete = at86rf230_async_state_delay;
 	rc = spi_async(lp->spi, &ctx->msg);
 	if (rc) {
 		if (ctx->irq_enable)
-			enable_irq(lp->spi->irq);
+			enable_irq(ctx->irq);
 
 		at86rf230_async_error(lp, ctx, rc);
 	}
@@ -689,7 +735,7 @@ at86rf230_sync_state_change_complete(void *context)
 static int
 at86rf230_sync_state_change(struct at86rf230_local *lp, unsigned int state)
 {
-	int rc;
+	unsigned long rc;
 
 	at86rf230_async_state_change(lp, &lp->state, state,
 				     at86rf230_sync_state_change_complete,
@@ -710,11 +756,10 @@ at86rf230_tx_complete(void *context)
 {
 	struct at86rf230_state_change *ctx = context;
 	struct at86rf230_local *lp = ctx->lp;
-	struct sk_buff *skb = lp->tx_skb;
 
-	enable_irq(lp->spi->irq);
+	enable_irq(ctx->irq);
 
-	ieee802154_xmit_complete(lp->hw, skb, !lp->tx_aret);
+	ieee802154_xmit_complete(lp->hw, lp->tx_skb, !lp->tx_aret);
 }
 
 static void
@@ -723,7 +768,7 @@ at86rf230_tx_on(void *context)
 	struct at86rf230_state_change *ctx = context;
 	struct at86rf230_local *lp = ctx->lp;
 
-	at86rf230_async_state_change(lp, &lp->irq, STATE_RX_AACK_ON,
+	at86rf230_async_state_change(lp, ctx, STATE_RX_AACK_ON,
 				     at86rf230_tx_complete, true);
 }
 
@@ -767,14 +812,25 @@ at86rf230_tx_trac_status(void *context)
 }
 
 static void
-at86rf230_rx(struct at86rf230_local *lp,
-	     const u8 *data, const u8 len, const u8 lqi)
+at86rf230_rx_read_frame_complete(void *context)
 {
-	struct sk_buff *skb;
+	struct at86rf230_state_change *ctx = context;
+	struct at86rf230_local *lp = ctx->lp;
 	u8 rx_local_buf[AT86RF2XX_MAX_BUF];
+	const u8 *buf = ctx->buf;
+	struct sk_buff *skb;
+	u8 len, lqi;
+
+	len = buf[1];
+	if (!ieee802154_is_valid_psdu_len(len)) {
+		dev_vdbg(&lp->spi->dev, "corrupted frame received\n");
+		len = IEEE802154_MTU;
+	}
+	lqi = buf[2 + len];
 
-	memcpy(rx_local_buf, data, len);
-	enable_irq(lp->spi->irq);
+	memcpy(rx_local_buf, buf + 2, len);
+	ctx->trx.len = 2;
+	enable_irq(ctx->irq);
 
 	skb = dev_alloc_skb(IEEE802154_MTU);
 	if (!skb) {
@@ -787,60 +843,41 @@ at86rf230_rx(struct at86rf230_local *lp,
 }
 
 static void
-at86rf230_rx_read_frame_complete(void *context)
+at86rf230_rx_read_frame(void *context)
 {
 	struct at86rf230_state_change *ctx = context;
 	struct at86rf230_local *lp = ctx->lp;
-	const u8 *buf = lp->irq.buf;
-	u8 len = buf[1];
-
-	if (!ieee802154_is_valid_psdu_len(len)) {
-		dev_vdbg(&lp->spi->dev, "corrupted frame received\n");
-		len = IEEE802154_MTU;
-	}
-
-	at86rf230_rx(lp, buf + 2, len, buf[2 + len]);
-}
-
-static void
-at86rf230_rx_read_frame(struct at86rf230_local *lp)
-{
+	u8 *buf = ctx->buf;
 	int rc;
 
-	u8 *buf = lp->irq.buf;
-
 	buf[0] = CMD_FB;
-	lp->irq.trx.len = AT86RF2XX_MAX_BUF;
-	lp->irq.msg.complete = at86rf230_rx_read_frame_complete;
-	rc = spi_async(lp->spi, &lp->irq.msg);
+	ctx->trx.len = AT86RF2XX_MAX_BUF;
+	ctx->msg.complete = at86rf230_rx_read_frame_complete;
+	rc = spi_async(lp->spi, &ctx->msg);
 	if (rc) {
-		enable_irq(lp->spi->irq);
-		at86rf230_async_error(lp, &lp->irq, rc);
+		ctx->trx.len = 2;
+		enable_irq(ctx->irq);
+		at86rf230_async_error(lp, ctx, rc);
 	}
 }
 
 static void
 at86rf230_rx_trac_check(void *context)
 {
-	struct at86rf230_state_change *ctx = context;
-	struct at86rf230_local *lp = ctx->lp;
-
 	/* Possible check on trac status here. This could be useful to make
 	 * some stats why receive is failed. Not used at the moment, but it's
 	 * maybe timing relevant. Datasheet doesn't say anything about this.
 	 * The programming guide say do it so.
 	 */
 
-	at86rf230_rx_read_frame(lp);
+	at86rf230_rx_read_frame(context);
 }
 
 static void
 at86rf230_irq_trx_end(struct at86rf230_local *lp)
 {
-	spin_lock(&lp->lock);
 	if (lp->is_tx) {
 		lp->is_tx = 0;
-		spin_unlock(&lp->lock);
 
 		if (lp->tx_aret)
 			at86rf230_async_state_change(lp, &lp->irq,
@@ -853,7 +890,6 @@ at86rf230_irq_trx_end(struct at86rf230_local *lp)
 						     at86rf230_tx_complete,
 						     true);
 	} else {
-		spin_unlock(&lp->lock);
 		at86rf230_async_read_reg(lp, RG_TRX_STATE, &lp->irq,
 					 at86rf230_rx_trac_check, true);
 	}
@@ -864,13 +900,13 @@ at86rf230_irq_status(void *context)
 {
 	struct at86rf230_state_change *ctx = context;
 	struct at86rf230_local *lp = ctx->lp;
-	const u8 *buf = lp->irq.buf;
+	const u8 *buf = ctx->buf;
 	const u8 irq = buf[1];
 
 	if (irq & IRQ_TRX_END) {
 		at86rf230_irq_trx_end(lp);
 	} else {
-		enable_irq(lp->spi->irq);
+		enable_irq(ctx->irq);
 		dev_err(&lp->spi->dev, "not supported irq %02x received\n",
 			irq);
 	}
@@ -886,7 +922,6 @@ static irqreturn_t at86rf230_isr(int irq, void *data)
 	disable_irq_nosync(irq);
 
 	buf[0] = (RG_IRQ_STATUS & CMD_REG_MASK) | CMD_REG;
-	ctx->trx.len = 2;
 	ctx->msg.complete = at86rf230_irq_status;
 	rc = spi_async(lp->spi, &ctx->msg);
 	if (rc) {
@@ -921,21 +956,21 @@ at86rf230_write_frame(void *context)
 	struct at86rf230_state_change *ctx = context;
 	struct at86rf230_local *lp = ctx->lp;
 	struct sk_buff *skb = lp->tx_skb;
-	u8 *buf = lp->tx.buf;
+	u8 *buf = ctx->buf;
 	int rc;
 
-	spin_lock(&lp->lock);
 	lp->is_tx = 1;
-	spin_unlock(&lp->lock);
 
 	buf[0] = CMD_FB | CMD_WRITE;
 	buf[1] = skb->len + 2;
 	memcpy(buf + 2, skb->data, skb->len);
-	lp->tx.trx.len = skb->len + 2;
-	lp->tx.msg.complete = at86rf230_write_frame_complete;
-	rc = spi_async(lp->spi, &lp->tx.msg);
-	if (rc)
+	ctx->trx.len = skb->len + 2;
+	ctx->msg.complete = at86rf230_write_frame_complete;
+	rc = spi_async(lp->spi, &ctx->msg);
+	if (rc) {
+		ctx->trx.len = 2;
 		at86rf230_async_error(lp, ctx, rc);
+	}
 }
 
 static void
@@ -948,24 +983,45 @@ at86rf230_xmit_tx_on(void *context)
 				     at86rf230_write_frame, false);
 }
 
+static void
+at86rf230_xmit_start(void *context)
+{
+	struct at86rf230_state_change *ctx = context;
+	struct at86rf230_local *lp = ctx->lp;
+
+	/* In ARET mode we need to go into STATE_TX_ARET_ON after we
+	 * are in STATE_TX_ON. The pfad differs here, so we change
+	 * the complete handler.
+	 */
+	if (lp->tx_aret)
+		at86rf230_async_state_change(lp, ctx, STATE_TX_ON,
+					     at86rf230_xmit_tx_on, false);
+	else
+		at86rf230_async_state_change(lp, ctx, STATE_TX_ON,
+					     at86rf230_write_frame, false);
+}
+
 static int
 at86rf230_xmit(struct ieee802154_hw *hw, struct sk_buff *skb)
 {
 	struct at86rf230_local *lp = hw->priv;
 	struct at86rf230_state_change *ctx = &lp->tx;
 
-	void (*tx_complete)(void *context) = at86rf230_write_frame;
-
 	lp->tx_skb = skb;
+	lp->tx_retry = 0;
 
-	/* In ARET mode we need to go into STATE_TX_ARET_ON after we
-	 * are in STATE_TX_ON. The pfad differs here, so we change
-	 * the complete handler.
+	/* After 5 minutes in PLL and the same frequency we run again the
+	 * calibration loops which is recommended by at86rf2xx datasheets.
+	 *
+	 * The calibration is initiate by a state change from TRX_OFF
+	 * to TX_ON, the lp->cal_timeout should be reinit by state_delay
+	 * function then to start in the next 5 minutes.
 	 */
-	if (lp->tx_aret)
-		tx_complete = at86rf230_xmit_tx_on;
-
-	at86rf230_async_state_change(lp, ctx, STATE_TX_ON, tx_complete, false);
+	if (time_is_before_jiffies(lp->cal_timeout))
+		at86rf230_async_state_change(lp, ctx, STATE_TRX_OFF,
+					     at86rf230_xmit_start, false);
+	else
+		at86rf230_xmit_start(ctx);
 
 	return 0;
 }
@@ -981,6 +1037,9 @@ at86rf230_ed(struct ieee802154_hw *hw, u8 *level)
 static int
 at86rf230_start(struct ieee802154_hw *hw)
 {
+	struct at86rf230_local *lp = hw->priv;
+
+	lp->cal_timeout = jiffies + AT86RF2XX_CAL_LOOP_TIMEOUT;
 	return at86rf230_sync_state_change(hw->priv, STATE_RX_AACK_ON);
 }
 
@@ -1061,6 +1120,8 @@ at86rf230_channel(struct ieee802154_hw *hw, u8 page, u8 channel)
 	/* Wait for PLL */
 	usleep_range(lp->data->t_channel_switch,
 		     lp->data->t_channel_switch + 10);
+
+	lp->cal_timeout = jiffies + AT86RF2XX_CAL_LOOP_TIMEOUT;
 	return rc;
 }
 
@@ -1112,7 +1173,7 @@ at86rf230_set_hw_addr_filt(struct ieee802154_hw *hw,
 }
 
 static int
-at86rf230_set_txpower(struct ieee802154_hw *hw, int db)
+at86rf230_set_txpower(struct ieee802154_hw *hw, s8 db)
 {
 	struct at86rf230_local *lp = hw->priv;
 
@@ -1281,7 +1342,6 @@ static struct at86rf2xx_chip_data at86rf233_data = {
 	.t_off_to_tx_on = 80,
 	.t_frame = 4096,
 	.t_p_ack = 545,
-	.t_tx_timeout = 2000,
 	.rssi_base_val = -91,
 	.set_channel = at86rf23x_set_channel,
 	.get_desense_steps = at86rf23x_get_desens_steps
@@ -1295,7 +1355,6 @@ static struct at86rf2xx_chip_data at86rf231_data = {
 	.t_off_to_tx_on = 110,
 	.t_frame = 4096,
 	.t_p_ack = 545,
-	.t_tx_timeout = 2000,
 	.rssi_base_val = -91,
 	.set_channel = at86rf23x_set_channel,
 	.get_desense_steps = at86rf23x_get_desens_steps
@@ -1309,13 +1368,12 @@ static struct at86rf2xx_chip_data at86rf212_data = {
 	.t_off_to_tx_on = 200,
 	.t_frame = 4096,
 	.t_p_ack = 545,
-	.t_tx_timeout = 2000,
 	.rssi_base_val = -100,
 	.set_channel = at86rf212_set_channel,
 	.get_desense_steps = at86rf212_get_desens_steps
 };
 
-static int at86rf230_hw_init(struct at86rf230_local *lp)
+static int at86rf230_hw_init(struct at86rf230_local *lp, u8 xtal_trim)
 {
 	int rc, irq_type, irq_pol = IRQ_ACTIVE_HIGH;
 	unsigned int dvdd;
@@ -1326,7 +1384,12 @@ static int at86rf230_hw_init(struct at86rf230_local *lp)
 		return rc;
 
 	irq_type = irq_get_trigger_type(lp->spi->irq);
-	if (irq_type == IRQ_TYPE_EDGE_FALLING)
+	if (irq_type == IRQ_TYPE_EDGE_RISING ||
+	    irq_type == IRQ_TYPE_EDGE_FALLING)
+		dev_warn(&lp->spi->dev,
+			 "Using edge triggered irq's are not recommended!\n");
+	if (irq_type == IRQ_TYPE_EDGE_FALLING ||
+	    irq_type == IRQ_TYPE_LEVEL_LOW)
 		irq_pol = IRQ_ACTIVE_LOW;
 
 	rc = at86rf230_write_subreg(lp, SR_IRQ_POLARITY, irq_pol);
@@ -1341,6 +1404,11 @@ static int at86rf230_hw_init(struct at86rf230_local *lp)
 	if (rc)
 		return rc;
 
+	/* reset values differs in at86rf231 and at86rf233 */
+	rc = at86rf230_write_subreg(lp, SR_IRQ_MASK_MODE, 0);
+	if (rc)
+		return rc;
+
 	get_random_bytes(csma_seed, ARRAY_SIZE(csma_seed));
 	rc = at86rf230_write_subreg(lp, SR_CSMA_SEED_0, csma_seed[0]);
 	if (rc)
@@ -1362,6 +1430,45 @@ static int at86rf230_hw_init(struct at86rf230_local *lp)
 	usleep_range(lp->data->t_sleep_cycle,
 		     lp->data->t_sleep_cycle + 100);
 
+	/* xtal_trim value is calculated by:
+	 * CL = 0.5 * (CX + CTRIM + CPAR)
+	 *
+	 * whereas:
+	 * CL = capacitor of used crystal
+	 * CX = connected capacitors at xtal pins
+	 * CPAR = in all at86rf2xx datasheets this is a constant value 3 pF,
+	 *	  but this is different on each board setup. You need to fine
+	 *	  tuning this value via CTRIM.
+	 * CTRIM = variable capacitor setting. Resolution is 0.3 pF range is
+	 *	   0 pF upto 4.5 pF.
+	 *
+	 * Examples:
+	 * atben transceiver:
+	 *
+	 * CL = 8 pF
+	 * CX = 12 pF
+	 * CPAR = 3 pF (We assume the magic constant from datasheet)
+	 * CTRIM = 0.9 pF
+	 *
+	 * (12+0.9+3)/2 = 7.95 which is nearly at 8 pF
+	 *
+	 * xtal_trim = 0x3
+	 *
+	 * openlabs transceiver:
+	 *
+	 * CL = 16 pF
+	 * CX = 22 pF
+	 * CPAR = 3 pF (We assume the magic constant from datasheet)
+	 * CTRIM = 4.5 pF
+	 *
+	 * (22+4.5+3)/2 = 14.75 which is the nearest value to 16 pF
+	 *
+	 * xtal_trim = 0xf
+	 */
+	rc = at86rf230_write_subreg(lp, SR_XTAL_TRIM, xtal_trim);
+	if (rc)
+		return rc;
+
 	rc = at86rf230_read_subreg(lp, SR_DVDD_OK, &dvdd);
 	if (rc)
 		return rc;
@@ -1377,24 +1484,30 @@ static int at86rf230_hw_init(struct at86rf230_local *lp)
 	return at86rf230_write_subreg(lp, SR_SLOTTED_OPERATION, 0);
 }
 
-static struct at86rf230_platform_data *
-at86rf230_get_pdata(struct spi_device *spi)
+static int
+at86rf230_get_pdata(struct spi_device *spi, int *rstn, int *slp_tr,
+		    u8 *xtal_trim)
 {
-	struct at86rf230_platform_data *pdata;
+	struct at86rf230_platform_data *pdata = spi->dev.platform_data;
+	int ret;
 
-	if (!IS_ENABLED(CONFIG_OF) || !spi->dev.of_node)
-		return spi->dev.platform_data;
+	if (!IS_ENABLED(CONFIG_OF) || !spi->dev.of_node) {
+		if (!pdata)
+			return -ENOENT;
 
-	pdata = devm_kzalloc(&spi->dev, sizeof(*pdata), GFP_KERNEL);
-	if (!pdata)
-		goto done;
+		*rstn = pdata->rstn;
+		*slp_tr = pdata->slp_tr;
+		*xtal_trim = pdata->xtal_trim;
+		return 0;
+	}
 
-	pdata->rstn = of_get_named_gpio(spi->dev.of_node, "reset-gpio", 0);
-	pdata->slp_tr = of_get_named_gpio(spi->dev.of_node, "sleep-gpio", 0);
+	*rstn = of_get_named_gpio(spi->dev.of_node, "reset-gpio", 0);
+	*slp_tr = of_get_named_gpio(spi->dev.of_node, "sleep-gpio", 0);
+	ret = of_property_read_u8(spi->dev.of_node, "xtal-trim", xtal_trim);
+	if (ret < 0 && ret != -EINVAL)
+		return ret;
 
-	spi->dev.platform_data = pdata;
-done:
-	return pdata;
+	return 0;
 }
 
 static int
@@ -1478,66 +1591,78 @@ static void
 at86rf230_setup_spi_messages(struct at86rf230_local *lp)
 {
 	lp->state.lp = lp;
+	lp->state.irq = lp->spi->irq;
 	spi_message_init(&lp->state.msg);
 	lp->state.msg.context = &lp->state;
+	lp->state.trx.len = 2;
 	lp->state.trx.tx_buf = lp->state.buf;
 	lp->state.trx.rx_buf = lp->state.buf;
 	spi_message_add_tail(&lp->state.trx, &lp->state.msg);
+	hrtimer_init(&lp->state.timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+	lp->state.timer.function = at86rf230_async_state_timer;
 
 	lp->irq.lp = lp;
+	lp->irq.irq = lp->spi->irq;
 	spi_message_init(&lp->irq.msg);
 	lp->irq.msg.context = &lp->irq;
+	lp->irq.trx.len = 2;
 	lp->irq.trx.tx_buf = lp->irq.buf;
 	lp->irq.trx.rx_buf = lp->irq.buf;
 	spi_message_add_tail(&lp->irq.trx, &lp->irq.msg);
+	hrtimer_init(&lp->irq.timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+	lp->irq.timer.function = at86rf230_async_state_timer;
 
 	lp->tx.lp = lp;
+	lp->tx.irq = lp->spi->irq;
 	spi_message_init(&lp->tx.msg);
 	lp->tx.msg.context = &lp->tx;
+	lp->tx.trx.len = 2;
 	lp->tx.trx.tx_buf = lp->tx.buf;
 	lp->tx.trx.rx_buf = lp->tx.buf;
 	spi_message_add_tail(&lp->tx.trx, &lp->tx.msg);
+	hrtimer_init(&lp->tx.timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+	lp->tx.timer.function = at86rf230_async_state_timer;
 }
 
 static int at86rf230_probe(struct spi_device *spi)
 {
-	struct at86rf230_platform_data *pdata;
 	struct ieee802154_hw *hw;
 	struct at86rf230_local *lp;
 	unsigned int status;
-	int rc, irq_type;
+	int rc, irq_type, rstn, slp_tr;
+	u8 xtal_trim = 0;
 
 	if (!spi->irq) {
 		dev_err(&spi->dev, "no IRQ specified\n");
 		return -EINVAL;
 	}
 
-	pdata = at86rf230_get_pdata(spi);
-	if (!pdata) {
-		dev_err(&spi->dev, "no platform_data\n");
-		return -EINVAL;
+	rc = at86rf230_get_pdata(spi, &rstn, &slp_tr, &xtal_trim);
+	if (rc < 0) {
+		dev_err(&spi->dev, "failed to parse platform_data: %d\n", rc);
+		return rc;
 	}
 
-	if (gpio_is_valid(pdata->rstn)) {
-		rc = devm_gpio_request_one(&spi->dev, pdata->rstn,
+	if (gpio_is_valid(rstn)) {
+		rc = devm_gpio_request_one(&spi->dev, rstn,
 					   GPIOF_OUT_INIT_HIGH, "rstn");
 		if (rc)
 			return rc;
 	}
 
-	if (gpio_is_valid(pdata->slp_tr)) {
-		rc = devm_gpio_request_one(&spi->dev, pdata->slp_tr,
+	if (gpio_is_valid(slp_tr)) {
+		rc = devm_gpio_request_one(&spi->dev, slp_tr,
 					   GPIOF_OUT_INIT_LOW, "slp_tr");
 		if (rc)
 			return rc;
 	}
 
 	/* Reset */
-	if (gpio_is_valid(pdata->rstn)) {
+	if (gpio_is_valid(rstn)) {
 		udelay(1);
-		gpio_set_value(pdata->rstn, 0);
+		gpio_set_value(rstn, 0);
 		udelay(1);
-		gpio_set_value(pdata->rstn, 1);
+		gpio_set_value(rstn, 1);
 		usleep_range(120, 240);
 	}
 
@@ -1566,12 +1691,11 @@ static int at86rf230_probe(struct spi_device *spi)
 	if (rc < 0)
 		goto free_dev;
 
-	spin_lock_init(&lp->lock);
 	init_completion(&lp->state_complete);
 
 	spi_set_drvdata(spi, lp);
 
-	rc = at86rf230_hw_init(lp);
+	rc = at86rf230_hw_init(lp, xtal_trim);
 	if (rc)
 		goto free_dev;