diff options
Diffstat (limited to 'drivers/net/igb/e1000_phy.c')
| -rw-r--r-- | drivers/net/igb/e1000_phy.c | 206 |
1 files changed, 194 insertions, 12 deletions
diff --git a/drivers/net/igb/e1000_phy.c b/drivers/net/igb/e1000_phy.c index cf1f32300923..ddd036a78999 100644 --- a/drivers/net/igb/e1000_phy.c +++ b/drivers/net/igb/e1000_phy.c @@ -570,6 +570,89 @@ out: } /** + * igb_copper_link_setup_m88_gen2 - Setup m88 PHY's for copper link + * @hw: pointer to the HW structure + * + * Sets up MDI/MDI-X and polarity for i347-AT4, m88e1322 and m88e1112 PHY's. + * Also enables and sets the downshift parameters. + **/ +s32 igb_copper_link_setup_m88_gen2(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + + if (phy->reset_disable) { + ret_val = 0; + goto out; + } + + /* Enable CRS on Tx. This must be set for half-duplex operation. */ + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + goto out; + + /* + * Options: + * MDI/MDI-X = 0 (default) + * 0 - Auto for all speeds + * 1 - MDI mode + * 2 - MDI-X mode + * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) + */ + phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; + + switch (phy->mdix) { + case 1: + phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE; + break; + case 2: + phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE; + break; + case 3: + /* M88E1112 does not support this mode) */ + if (phy->id != M88E1112_E_PHY_ID) { + phy_data |= M88E1000_PSCR_AUTO_X_1000T; + break; + } + case 0: + default: + phy_data |= M88E1000_PSCR_AUTO_X_MODE; + break; + } + + /* + * Options: + * disable_polarity_correction = 0 (default) + * Automatic Correction for Reversed Cable Polarity + * 0 - Disabled + * 1 - Enabled + */ + phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL; + if (phy->disable_polarity_correction == 1) + phy_data |= M88E1000_PSCR_POLARITY_REVERSAL; + + /* Enable downshift and setting it to X6 */ + phy_data &= ~I347AT4_PSCR_DOWNSHIFT_MASK; + phy_data |= I347AT4_PSCR_DOWNSHIFT_6X; + phy_data |= I347AT4_PSCR_DOWNSHIFT_ENABLE; + + ret_val = phy->ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + if (ret_val) + goto out; + + /* Commit the changes. */ + ret_val = igb_phy_sw_reset(hw); + if (ret_val) { + hw_dbg("Error committing the PHY changes\n"); + goto out; + } + +out: + return ret_val; +} + +/** * igb_copper_link_setup_igp - Setup igp PHY's for copper link * @hw: pointer to the HW structure * @@ -1124,18 +1207,25 @@ s32 igb_phy_force_speed_duplex_m88(struct e1000_hw *hw) goto out; if (!link) { - /* - * We didn't get link. - * Reset the DSP and cross our fingers. - */ - ret_val = phy->ops.write_reg(hw, - M88E1000_PHY_PAGE_SELECT, - 0x001d); - if (ret_val) - goto out; - ret_val = igb_phy_reset_dsp(hw); - if (ret_val) - goto out; + if (hw->phy.type != e1000_phy_m88 || + hw->phy.id == I347AT4_E_PHY_ID || + hw->phy.id == M88E1112_E_PHY_ID) { + hw_dbg("Link taking longer than expected.\n"); + } else { + + /* + * We didn't get link. + * Reset the DSP and cross our fingers. + */ + ret_val = phy->ops.write_reg(hw, + M88E1000_PHY_PAGE_SELECT, + 0x001d); + if (ret_val) + goto out; + ret_val = igb_phy_reset_dsp(hw); + if (ret_val) + goto out; + } } /* Try once more */ @@ -1145,6 +1235,11 @@ s32 igb_phy_force_speed_duplex_m88(struct e1000_hw *hw) goto out; } + if (hw->phy.type != e1000_phy_m88 || + hw->phy.id == I347AT4_E_PHY_ID || + hw->phy.id == M88E1112_E_PHY_ID) + goto out; + ret_val = phy->ops.read_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); if (ret_val) goto out; @@ -1557,6 +1652,93 @@ out: return ret_val; } +s32 igb_get_cable_length_m88_gen2(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data, phy_data2, index, default_page, is_cm; + + switch (hw->phy.id) { + case I347AT4_E_PHY_ID: + /* Remember the original page select and set it to 7 */ + ret_val = phy->ops.read_reg(hw, I347AT4_PAGE_SELECT, + &default_page); + if (ret_val) + goto out; + + ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT, 0x07); + if (ret_val) + goto out; + + /* Get cable length from PHY Cable Diagnostics Control Reg */ + ret_val = phy->ops.read_reg(hw, (I347AT4_PCDL + phy->addr), + &phy_data); + if (ret_val) + goto out; + + /* Check if the unit of cable length is meters or cm */ + ret_val = phy->ops.read_reg(hw, I347AT4_PCDC, &phy_data2); + if (ret_val) + goto out; + + is_cm = !(phy_data & I347AT4_PCDC_CABLE_LENGTH_UNIT); + + /* Populate the phy structure with cable length in meters */ + phy->min_cable_length = phy_data / (is_cm ? 100 : 1); + phy->max_cable_length = phy_data / (is_cm ? 100 : 1); + phy->cable_length = phy_data / (is_cm ? 100 : 1); + + /* Reset the page selec to its original value */ + ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT, + default_page); + if (ret_val) + goto out; + break; + case M88E1112_E_PHY_ID: + /* Remember the original page select and set it to 5 */ + ret_val = phy->ops.read_reg(hw, I347AT4_PAGE_SELECT, + &default_page); + if (ret_val) + goto out; + + ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT, 0x05); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, M88E1112_VCT_DSP_DISTANCE, + &phy_data); + if (ret_val) + goto out; + + index = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >> + M88E1000_PSSR_CABLE_LENGTH_SHIFT; + if (index >= M88E1000_CABLE_LENGTH_TABLE_SIZE - 1) { + ret_val = -E1000_ERR_PHY; + goto out; + } + + phy->min_cable_length = e1000_m88_cable_length_table[index]; + phy->max_cable_length = e1000_m88_cable_length_table[index + 1]; + + phy->cable_length = (phy->min_cable_length + + phy->max_cable_length) / 2; + + /* Reset the page select to its original value */ + ret_val = phy->ops.write_reg(hw, I347AT4_PAGE_SELECT, + default_page); + if (ret_val) + goto out; + + break; + default: + ret_val = -E1000_ERR_PHY; + goto out; + } + +out: + return ret_val; +} + /** * igb_get_cable_length_igp_2 - Determine cable length for igp2 PHY * @hw: pointer to the HW structure |