diff options
Diffstat (limited to 'drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h')
| -rw-r--r-- | drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h | 152 |
1 files changed, 144 insertions, 8 deletions
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h index 23208f79b97c..e545e849f5a3 100644 --- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h +++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_regs.h @@ -45,6 +45,7 @@ #define APS_FSMCO_ENABLE_POWERDOWN BIT(4) #define APS_FSMCO_MAC_ENABLE BIT(8) #define APS_FSMCO_MAC_OFF BIT(9) +#define APS_FSMCO_SW_LPS BIT(10) #define APS_FSMCO_HW_SUSPEND BIT(11) #define APS_FSMCO_PCIE BIT(12) #define APS_FSMCO_HW_POWERDOWN BIT(15) @@ -69,8 +70,11 @@ #define REG_EE_VPD 0x000c #define REG_AFE_MISC 0x0010 +#define AFE_MISC_WL_XTAL_CTRL BIT(6) + #define REG_SPS0_CTRL 0x0011 #define REG_SPS_OCP_CFG 0x0018 +#define REG_8192E_LDOV12_CTRL 0x0014 #define REG_RSV_CTRL 0x001c #define REG_RF_CTRL 0x001f @@ -131,6 +135,8 @@ #define EFUSE_ACCESS_DISABLE 0x00 /* RTL8723 only */ #define REG_PWR_DATA 0x0038 +#define PWR_DATA_EEPRPAD_RFE_CTRL_EN BIT(11) + #define REG_CAL_TIMER 0x003c #define REG_ACLK_MON 0x003e #define REG_GPIO_MUXCFG 0x0040 @@ -138,7 +144,10 @@ #define REG_MAC_PINMUX_CFG 0x0043 #define REG_GPIO_PIN_CTRL 0x0044 #define REG_GPIO_INTM 0x0048 +#define GPIO_INTM_EDGE_TRIG_IRQ BIT(9) + #define REG_LEDCFG0 0x004c +#define LEDCFG0_DPDT_SELECT BIT(23) #define REG_LEDCFG1 0x004d #define REG_LEDCFG2 0x004e #define LEDCFG2_DPDT_SELECT BIT(7) @@ -152,6 +161,12 @@ #define REG_GPIO_PIN_CTRL_2 0x0060 /* RTL8723 WIFI/BT/GPS Multi-Function GPIO Select. */ #define REG_GPIO_IO_SEL_2 0x0062 +#define GPIO_IO_SEL_2_GPIO09_INPUT BIT(1) +#define GPIO_IO_SEL_2_GPIO09_IRQ BIT(9) + +/* RTL8723B */ +#define REG_PAD_CTRL1 0x0064 +#define PAD_CTRL1_SW_DPDT_SEL_DATA BIT(0) /* RTL8723 only WIFI/BT/GPS Multi-Function control source. */ #define REG_MULTI_FUNC_CTRL 0x0068 @@ -177,6 +192,8 @@ control */ #define MULTI_GPS_FUNC_EN BIT(22) /* GPS function enable */ +#define REG_LDO_SW_CTRL 0x007c /* 8192eu */ + #define REG_MCU_FW_DL 0x0080 #define MCU_FW_DL_ENABLE BIT(0) #define MCU_FW_DL_READY BIT(1) @@ -192,6 +209,12 @@ #define REG_HMBOX_EXT_1 0x008a #define REG_HMBOX_EXT_2 0x008c #define REG_HMBOX_EXT_3 0x008e +/* Interrupt registers for 8192e/8723bu/8812 */ +#define REG_HIMR0 0x00b0 +#define REG_HISR0 0x00b4 +#define REG_HIMR1 0x00b8 +#define REG_HISR1 0x00bc + /* Host suspend counter on FPGA platform */ #define REG_HOST_SUSP_CNT 0x00bc /* Efuse access protection for RTL8723 */ @@ -213,6 +236,7 @@ #define SYS_CFG_PCIRSTB BIT(4) #define SYS_CFG_V15_VLD BIT(5) #define SYS_CFG_TRP_B15V_EN BIT(7) +#define SYS_CFG_SW_OFFLOAD_EN BIT(7) /* For chips with IOL support */ #define SYS_CFG_SIC_IDLE BIT(8) #define SYS_CFG_BD_MAC2 BIT(9) #define SYS_CFG_BD_MAC1 BIT(10) @@ -220,9 +244,14 @@ #define SYS_CFG_CHIP_VER (BIT(12) | BIT(13) | BIT(14) | BIT(15)) #define SYS_CFG_BT_FUNC BIT(16) #define SYS_CFG_VENDOR_ID BIT(19) +#define SYS_CFG_VENDOR_EXT_MASK (BIT(18) | BIT(19)) +#define SYS_CFG_VENDOR_ID_TSMC 0 +#define SYS_CFG_VENDOR_ID_SMIC BIT(18) +#define SYS_CFG_VENDOR_ID_UMC BIT(19) #define SYS_CFG_PAD_HWPD_IDN BIT(22) #define SYS_CFG_TRP_VAUX_EN BIT(23) #define SYS_CFG_TRP_BT_EN BIT(24) +#define SYS_CFG_SPS_LDO_SEL BIT(24) /* 8192eu */ #define SYS_CFG_BD_PKG_SEL BIT(25) #define SYS_CFG_BD_HCI_SEL BIT(26) #define SYS_CFG_TYPE_ID BIT(27) @@ -255,6 +284,8 @@ #define GPIO_USB_SUSEN BIT(23) #define GPIO_RF_RL_ID (BIT(31) | BIT(30) | BIT(29) | BIT(28)) +#define REG_SYS_CFG2 0x00fc /* 8192eu */ + /* 0x0100 ~ 0x01FF MACTOP General Configuration */ #define REG_CR 0x0100 #define CR_HCI_TXDMA_ENABLE BIT(0) @@ -287,6 +318,7 @@ #define PBP_PAGE_SIZE_1024 0x4 #define REG_TRXDMA_CTRL 0x010c +#define TRXDMA_CTRL_RXDMA_AGG_EN BIT(2) #define TRXDMA_CTRL_VOQ_SHIFT 4 #define TRXDMA_CTRL_VIQ_SHIFT 6 #define TRXDMA_CTRL_BEQ_SHIFT 8 @@ -321,6 +353,8 @@ #define REG_MBIST_DONE 0x0178 #define REG_MBIST_FAIL 0x017c #define REG_C2HEVT_MSG_NORMAL 0x01a0 +/* 8192EU/8723BU/8812 */ +#define REG_C2HEVT_CMD_ID_8723B 0x01ae #define REG_C2HEVT_CLEAR 0x01af #define REG_C2HEVT_MSG_TEST 0x01b8 #define REG_MCUTST_1 0x01c0 @@ -340,6 +374,11 @@ #define REG_BB_ACCEESS_CTRL 0x01e8 #define REG_BB_ACCESS_DATA 0x01ec +#define REG_HMBOX_EXT0_8723B 0x01f0 +#define REG_HMBOX_EXT1_8723B 0x01f4 +#define REG_HMBOX_EXT2_8723B 0x01f8 +#define REG_HMBOX_EXT3_8723B 0x01fc + /* 0x0200 ~ 0x027F TXDMA Configuration */ #define REG_RQPN 0x0200 #define RQPN_HI_PQ_SHIFT 0 @@ -350,14 +389,29 @@ #define REG_FIFOPAGE 0x0204 #define REG_TDECTRL 0x0208 #define REG_TXDMA_OFFSET_CHK 0x020c +#define TXDMA_OFFSET_DROP_DATA_EN BIT(9) #define REG_TXDMA_STATUS 0x0210 #define REG_RQPN_NPQ 0x0214 +#define RQPN_NPQ_SHIFT 0 +#define RQPN_EPQ_SHIFT 16 + +#define REG_AUTO_LLT 0x0224 +#define AUTO_LLT_INIT_LLT BIT(16) + +#define REG_DWBCN1_CTRL_8723B 0x0228 /* 0x0280 ~ 0x02FF RXDMA Configuration */ #define REG_RXDMA_AGG_PG_TH 0x0280 +#define RXDMA_USB_AGG_ENABLE BIT(31) #define REG_RXPKT_NUM 0x0284 +#define RXPKT_NUM_RXDMA_IDLE BIT(17) +#define RXPKT_NUM_RW_RELEASE_EN BIT(18) #define REG_RXDMA_STATUS 0x0288 +/* Presumably only found on newer chips such as 8723bu */ +#define REG_RX_DMA_CTRL_8723B 0x0286 +#define REG_RXDMA_PRO_8723B 0x0290 + #define REG_RF_BB_CMD_ADDR 0x02c0 #define REG_RF_BB_CMD_DATA 0x02c4 @@ -429,20 +483,26 @@ #define REG_ARFR1 0x0448 #define REG_ARFR2 0x044c #define REG_ARFR3 0x0450 +#define REG_AMPDU_MAX_TIME_8723B 0x0456 #define REG_AGGLEN_LMT 0x0458 #define REG_AMPDU_MIN_SPACE 0x045c #define REG_TXPKTBUF_WMAC_LBK_BF_HD 0x045d #define REG_FAST_EDCA_CTRL 0x0460 #define REG_RD_RESP_PKT_TH 0x0463 #define REG_INIRTS_RATE_SEL 0x0480 +/* 8723bu */ +#define REG_DATA_SUBCHANNEL 0x0483 +/* 8723au */ #define REG_INIDATA_RATE_SEL 0x0484 #define REG_POWER_STATUS 0x04a4 #define REG_POWER_STAGE1 0x04b4 #define REG_POWER_STAGE2 0x04b8 +#define REG_AMPDU_BURST_MODE_8723B 0x04bc #define REG_PKT_VO_VI_LIFE_TIME 0x04c0 #define REG_PKT_BE_BK_LIFE_TIME 0x04c2 #define REG_STBC_SETTING 0x04c4 +#define REG_HT_SINGLE_AMPDU_8723B 0x04c7 #define REG_PROT_MODE_CTRL 0x04c8 #define REG_MAX_AGGR_NUM 0x04ca #define REG_RTS_MAX_AGGR_NUM 0x04cb @@ -453,6 +513,10 @@ #define REG_NEED_CPU_HANDLE 0x04e0 #define REG_PKT_LOSE_RPT 0x04e1 #define REG_PTCL_ERR_STATUS 0x04e2 +#define REG_TX_REPORT_CTRL 0x04ec +#define TX_REPORT_CTRL_TIMER_ENABLE BIT(1) + +#define REG_TX_REPORT_TIME 0x04f0 #define REG_DUMMY 0x04fc /* 0x0500 ~ 0x05FF EDCA Configuration */ @@ -505,6 +569,7 @@ #define BEACON_DMA_ATIME_INT_TIME 2 #define REG_ATIMWND 0x055a +#define REG_USTIME_TSF_8723B 0x055c #define REG_BCN_MAX_ERR 0x055d #define REG_RXTSF_OFFSET_CCK 0x055e #define REG_RXTSF_OFFSET_OFDM 0x055f @@ -559,13 +624,25 @@ (Rx beacon, probe rsp) */ #define RCR_ACCEPT_CRC32 BIT(8) /* Accept CRC32 error packet */ #define RCR_ACCEPT_ICV BIT(9) /* Accept ICV error packet */ -#define RCR_ACCEPT_DATA_FRAME BIT(11) -#define RCR_ACCEPT_CTRL_FRAME BIT(12) -#define RCR_ACCEPT_MGMT_FRAME BIT(13) +#define RCR_ACCEPT_DATA_FRAME BIT(11) /* Accept all data pkt or use + REG_RXFLTMAP2 */ +#define RCR_ACCEPT_CTRL_FRAME BIT(12) /* Accept all control pkt or use + REG_RXFLTMAP1 */ +#define RCR_ACCEPT_MGMT_FRAME BIT(13) /* Accept all mgmt pkt or use + REG_RXFLTMAP0 */ #define RCR_HTC_LOC_CTRL BIT(14) /* MFC<--HTC=1 MFC-->HTC=0 */ +#define RCR_UC_DATA_PKT_INT_ENABLE BIT(16) /* Enable unicast data packet + interrupt */ +#define RCR_BM_DATA_PKT_INT_ENABLE BIT(17) /* Enable broadcast data packet + interrupt */ +#define RCR_TIM_PARSER_ENABLE BIT(18) /* Enable RX beacon TIM parser*/ #define RCR_MFBEN BIT(22) -#define RCR_LSIGEN BIT(23) +#define RCR_LSIG_ENABLE BIT(23) /* Enable LSIG TXOP Protection + function. Search KEYCAM for + each rx packet to check if + LSIGEN bit is set. */ #define RCR_MULTI_BSSID_ENABLE BIT(24) /* Enable Multiple BssId */ +#define RCR_FORCE_ACK BIT(26) #define RCR_ACCEPT_BA_SSN BIT(27) /* Accept BA SSN */ #define RCR_APPEND_PHYSTAT BIT(28) #define RCR_APPEND_ICV BIT(29) @@ -605,6 +682,10 @@ #define REG_FWDLY 0x0661 #define REG_RXERR_RPT 0x0664 #define REG_WMAC_TRXPTCL_CTL 0x0668 +#define WMAC_TRXPTCL_CTL_BW_MASK (BIT(7) | BIT(8)) +#define WMAC_TRXPTCL_CTL_BW_20 0 +#define WMAC_TRXPTCL_CTL_BW_40 BIT(7) +#define WMAC_TRXPTCL_CTL_BW_80 BIT(8) /* Security */ #define REG_CAM_CMD 0x0670 @@ -632,18 +713,40 @@ #define REG_LPNAV_CTRL 0x0694 #define REG_WKFMCAM_CMD 0x0698 #define REG_WKFMCAM_RWD 0x069c -#define REG_RXFLTMAP0 0x06a0 -#define REG_RXFLTMAP1 0x06a2 -#define REG_RXFLTMAP2 0x06a4 + +/* + * RX Filters: each bit corresponds to the numerical value of the subtype. + * If it is set the subtype frame type is passed. The filter is only used when + * the RCR_ACCEPT_DATA_FRAME, RCR_ACCEPT_CTRL_FRAME, RCR_ACCEPT_MGMT_FRAME bit + * in the RCR are low. + * + * Example: Beacon subtype is binary 1000 which is decimal 8 so we have to set + * bit 8 (0x100) in REG_RXFLTMAP0 to enable reception. + */ +#define REG_RXFLTMAP0 0x06a0 /* Management frames */ +#define REG_RXFLTMAP1 0x06a2 /* Control frames */ +#define REG_RXFLTMAP2 0x06a4 /* Data frames */ + #define REG_BCN_PSR_RPT 0x06a8 #define REG_CALB32K_CTRL 0x06ac #define REG_PKT_MON_CTRL 0x06b4 -#define REG_BT_COEX_TABLE 0x06c0 +#define REG_BT_COEX_TABLE1 0x06c0 +#define REG_BT_COEX_TABLE2 0x06c4 +#define REG_BT_COEX_TABLE3 0x06c8 +#define REG_BT_COEX_TABLE4 0x06cc #define REG_WMAC_RESP_TXINFO 0x06d8 #define REG_MACID1 0x0700 #define REG_BSSID1 0x0708 +/* + * This seems to be 8723bu specific + */ +#define REG_BT_CONTROL_8723BU 0x0764 +#define BT_CONTROL_BT_GRANT BIT(12) + +#define REG_WLAN_ACT_CONTROL_8723B 0x076e + #define REG_FPGA0_RF_MODE 0x0800 #define FPGA_RF_MODE BIT(0) #define FPGA_RF_MODE_JAPAN BIT(1) @@ -734,6 +837,11 @@ #define REG_FPGA0_ANALOG3 0x0888 #define REG_FPGA0_ANALOG4 0x088c +#define REG_NHM_TH9_TH10_8723B 0x0890 +#define REG_NHM_TIMER_8723B 0x0894 +#define REG_NHM_TH3_TO_TH0_8723B 0x0898 +#define REG_NHM_TH7_TO_TH4_8723B 0x089c + #define REG_FPGA0_XA_LSSI_READBACK 0x08a0 /* Tranceiver LSSI Readback */ #define REG_FPGA0_XB_LSSI_READBACK 0x08a4 #define REG_HSPI_XA_READBACK 0x08b8 /* Transceiver A HSPI read */ @@ -742,6 +850,11 @@ #define REG_FPGA1_RF_MODE 0x0900 #define REG_FPGA1_TX_INFO 0x090c +#define REG_DPDT_CTRL 0x092c /* 8723BU */ +#define REG_RFE_CTRL_ANTA_SRC 0x0930 /* 8723BU */ +#define REG_RFE_PATH_SELECT 0x0940 /* 8723BU */ +#define REG_RFE_BUFFER 0x0944 /* 8723BU */ +#define REG_S0S1_PATH_SWITCH 0x0948 /* 8723BU */ #define REG_CCK0_SYSTEM 0x0a00 #define CCK0_SIDEBAND BIT(4) @@ -765,11 +878,16 @@ #define REG_OFDM0_TR_MUX_PAR 0x0c08 +#define REG_OFDM0_FA_RSTC 0x0c0c + #define REG_OFDM0_XA_RX_IQ_IMBALANCE 0x0c14 #define REG_OFDM0_XB_RX_IQ_IMBALANCE 0x0c1c #define REG_OFDM0_ENERGY_CCA_THRES 0x0c4c +#define REG_OFDM0_RX_D_SYNC_PATH 0x0c40 +#define OFDM0_SYNC_PATH_NOTCH_FILTER BIT(1) + #define REG_OFDM0_XA_AGC_CORE1 0x0c50 #define REG_OFDM0_XA_AGC_CORE2 0x0c54 #define REG_OFDM0_XB_AGC_CORE1 0x0c58 @@ -794,6 +912,9 @@ #define REG_OFDM0_RX_IQ_EXT_ANTA 0x0ca0 +/* 8723bu */ +#define REG_OFDM0_TX_PSDO_NOISE_WEIGHT 0x0ce4 + #define REG_OFDM1_LSTF 0x0d00 #define OFDM_LSTF_PRIME_CH_LOW BIT(10) #define OFDM_LSTF_PRIME_CH_HIGH BIT(11) @@ -952,6 +1073,10 @@ #define RF6052_REG_MODE_AG 0x18 /* RF channel and BW switch */ #define MODE_AG_CHANNEL_MASK 0x3ff #define MODE_AG_CHANNEL_20MHZ BIT(10) +#define MODE_AG_BW_MASK (BIT(10) | BIT(11)) +#define MODE_AG_BW_20MHZ_8723B (BIT(10) | BIT(11)) +#define MODE_AG_BW_40MHZ_8723B BIT(10) +#define MODE_AG_BW_80MHZ_8723B 0 #define RF6052_REG_TOP 0x19 #define RF6052_REG_RX_G1 0x1a @@ -979,3 +1104,14 @@ #define RF6052_REG_TXPA_G1 0x31 /* RF TX PA control */ #define RF6052_REG_TXPA_G2 0x32 /* RF TX PA control */ #define RF6052_REG_TXPA_G3 0x33 /* RF TX PA control */ + +/* + * NextGen regs: 8723BU + */ +#define RF6052_REG_T_METER_8723B 0x42 +#define RF6052_REG_UNKNOWN_43 0x43 +#define RF6052_REG_UNKNOWN_55 0x55 +#define RF6052_REG_S0S1 0xb0 +#define RF6052_REG_UNKNOWN_DF 0xdf +#define RF6052_REG_UNKNOWN_ED 0xed +#define RF6052_REG_WE_LUT 0xef |