diff options
Diffstat (limited to 'drivers/phy/qualcomm')
| -rw-r--r-- | drivers/phy/qualcomm/Kconfig | 9 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/Makefile | 1 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-apq8064-sata.c | 10 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-ipq806x-sata.c | 10 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-pcie2.c | 331 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-qmp.c | 225 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-qmp.h | 12 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-qusb2.c | 13 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-ufs-i.h | 16 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c | 36 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h | 11 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c | 36 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h | 11 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-ufs.c | 70 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-usb-hs.c | 5 | ||||
| -rw-r--r-- | drivers/phy/qualcomm/phy-qcom-usb-hsic.c | 5 |
16 files changed, 581 insertions, 220 deletions
diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig index 32f7d34eb784..e46824da29f6 100644 --- a/drivers/phy/qualcomm/Kconfig +++ b/drivers/phy/qualcomm/Kconfig @@ -1,3 +1,4 @@ +# SPDX-License-Identifier: GPL-2.0-only # # Phy drivers for Qualcomm and Atheros platforms # @@ -24,6 +25,14 @@ config PHY_QCOM_IPQ806X_SATA depends on OF select GENERIC_PHY +config PHY_QCOM_PCIE2 + tristate "Qualcomm PCIe Gen2 PHY Driver" + depends on OF && COMMON_CLK && (ARCH_QCOM || COMPILE_TEST) + select GENERIC_PHY + help + Enable this to support the Qualcomm PCIe PHY, used with the Synopsys + based PCIe controller. + config PHY_QCOM_QMP tristate "Qualcomm QMP PHY Driver" depends on OF && COMMON_CLK && (ARCH_QCOM || COMPILE_TEST) diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile index c56efd3af205..283251d6a5d9 100644 --- a/drivers/phy/qualcomm/Makefile +++ b/drivers/phy/qualcomm/Makefile @@ -2,6 +2,7 @@ obj-$(CONFIG_PHY_ATH79_USB) += phy-ath79-usb.o obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o +obj-$(CONFIG_PHY_QCOM_PCIE2) += phy-qcom-pcie2.o obj-$(CONFIG_PHY_QCOM_QMP) += phy-qcom-qmp.o obj-$(CONFIG_PHY_QCOM_QUSB2) += phy-qcom-qusb2.o obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o diff --git a/drivers/phy/qualcomm/phy-qcom-apq8064-sata.c b/drivers/phy/qualcomm/phy-qcom-apq8064-sata.c index 69ce2afac015..42bc5150dd92 100644 --- a/drivers/phy/qualcomm/phy-qcom-apq8064-sata.c +++ b/drivers/phy/qualcomm/phy-qcom-apq8064-sata.c @@ -1,14 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-only /* * Copyright (c) 2014, The Linux Foundation. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 and - * only version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ #include <linux/io.h> diff --git a/drivers/phy/qualcomm/phy-qcom-ipq806x-sata.c b/drivers/phy/qualcomm/phy-qcom-ipq806x-sata.c index 0ad127cc9298..41a69f56b346 100644 --- a/drivers/phy/qualcomm/phy-qcom-ipq806x-sata.c +++ b/drivers/phy/qualcomm/phy-qcom-ipq806x-sata.c @@ -1,14 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-only /* * Copyright (c) 2014, The Linux Foundation. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 and - * only version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. */ #include <linux/io.h> diff --git a/drivers/phy/qualcomm/phy-qcom-pcie2.c b/drivers/phy/qualcomm/phy-qcom-pcie2.c new file mode 100644 index 000000000000..9dba3594e6d9 --- /dev/null +++ b/drivers/phy/qualcomm/phy-qcom-pcie2.c @@ -0,0 +1,331 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2014-2017, The Linux Foundation. All rights reserved. + * Copyright (c) 2019, Linaro Ltd. + */ + +#include <linux/clk-provider.h> +#include <linux/clk.h> +#include <linux/iopoll.h> +#include <linux/module.h> +#include <linux/phy/phy.h> +#include <linux/platform_device.h> +#include <linux/reset.h> +#include <linux/slab.h> + +#include <dt-bindings/phy/phy.h> + +#define PCIE20_PARF_PHY_STTS 0x3c +#define PCIE2_PHY_RESET_CTRL 0x44 +#define PCIE20_PARF_PHY_REFCLK_CTRL2 0xa0 +#define PCIE20_PARF_PHY_REFCLK_CTRL3 0xa4 +#define PCIE20_PARF_PCS_SWING_CTRL1 0x88 +#define PCIE20_PARF_PCS_SWING_CTRL2 0x8c +#define PCIE20_PARF_PCS_DEEMPH1 0x74 +#define PCIE20_PARF_PCS_DEEMPH2 0x78 +#define PCIE20_PARF_PCS_DEEMPH3 0x7c +#define PCIE20_PARF_CONFIGBITS 0x84 +#define PCIE20_PARF_PHY_CTRL3 0x94 +#define PCIE20_PARF_PCS_CTRL 0x80 + +#define TX_AMP_VAL 120 +#define PHY_RX0_EQ_GEN1_VAL 0 +#define PHY_RX0_EQ_GEN2_VAL 4 +#define TX_DEEMPH_GEN1_VAL 24 +#define TX_DEEMPH_GEN2_3_5DB_VAL 26 +#define TX_DEEMPH_GEN2_6DB_VAL 36 +#define PHY_TX0_TERM_OFFST_VAL 0 + +struct qcom_phy { + struct device *dev; + void __iomem *base; + + struct regulator_bulk_data vregs[2]; + + struct reset_control *phy_reset; + struct reset_control *pipe_reset; + struct clk *pipe_clk; +}; + +static int qcom_pcie2_phy_init(struct phy *phy) +{ + struct qcom_phy *qphy = phy_get_drvdata(phy); + int ret; + + ret = reset_control_deassert(qphy->phy_reset); + if (ret) { + dev_err(qphy->dev, "cannot deassert pipe reset\n"); + return ret; + } + + ret = regulator_bulk_enable(ARRAY_SIZE(qphy->vregs), qphy->vregs); + if (ret) + reset_control_assert(qphy->phy_reset); + + return ret; +} + +static int qcom_pcie2_phy_power_on(struct phy *phy) +{ + struct qcom_phy *qphy = phy_get_drvdata(phy); + int ret; + u32 val; + + /* Program REF_CLK source */ + val = readl(qphy->base + PCIE20_PARF_PHY_REFCLK_CTRL2); + val &= ~BIT(1); + writel(val, qphy->base + PCIE20_PARF_PHY_REFCLK_CTRL2); + + usleep_range(1000, 2000); + + /* Don't use PAD for refclock */ + val = readl(qphy->base + PCIE20_PARF_PHY_REFCLK_CTRL2); + val &= ~BIT(0); + writel(val, qphy->base + PCIE20_PARF_PHY_REFCLK_CTRL2); + + /* Program SSP ENABLE */ + val = readl(qphy->base + PCIE20_PARF_PHY_REFCLK_CTRL3); + val |= BIT(0); + writel(val, qphy->base + PCIE20_PARF_PHY_REFCLK_CTRL3); + + usleep_range(1000, 2000); + + /* Assert Phy SW Reset */ + val = readl(qphy->base + PCIE2_PHY_RESET_CTRL); + val |= BIT(0); + writel(val, qphy->base + PCIE2_PHY_RESET_CTRL); + + /* Program Tx Amplitude */ + val = readl(qphy->base + PCIE20_PARF_PCS_SWING_CTRL1); + val &= ~0x7f; + val |= TX_AMP_VAL; + writel(val, qphy->base + PCIE20_PARF_PCS_SWING_CTRL1); + + val = readl(qphy->base + PCIE20_PARF_PCS_SWING_CTRL2); + val &= ~0x7f; + val |= TX_AMP_VAL; + writel(val, qphy->base + PCIE20_PARF_PCS_SWING_CTRL2); + + /* Program De-Emphasis */ + val = readl(qphy->base + PCIE20_PARF_PCS_DEEMPH1); + val &= ~0x3f; + val |= TX_DEEMPH_GEN2_6DB_VAL; + writel(val, qphy->base + PCIE20_PARF_PCS_DEEMPH1); + + val = readl(qphy->base + PCIE20_PARF_PCS_DEEMPH2); + val &= ~0x3f; + val |= TX_DEEMPH_GEN2_3_5DB_VAL; + writel(val, qphy->base + PCIE20_PARF_PCS_DEEMPH2); + + val = readl(qphy->base + PCIE20_PARF_PCS_DEEMPH3); + val &= ~0x3f; + val |= TX_DEEMPH_GEN1_VAL; + writel(val, qphy->base + PCIE20_PARF_PCS_DEEMPH3); + + /* Program Rx_Eq */ + val = readl(qphy->base + PCIE20_PARF_CONFIGBITS); + val &= ~0x7; + val |= PHY_RX0_EQ_GEN2_VAL; + writel(val, qphy->base + PCIE20_PARF_CONFIGBITS); + + /* Program Tx0_term_offset */ + val = readl(qphy->base + PCIE20_PARF_PHY_CTRL3); + val &= ~0x1f; + val |= PHY_TX0_TERM_OFFST_VAL; + writel(val, qphy->base + PCIE20_PARF_PHY_CTRL3); + + /* disable Tx2Rx Loopback */ + val = readl(qphy->base + PCIE20_PARF_PCS_CTRL); + val &= ~BIT(1); + writel(val, qphy->base + PCIE20_PARF_PCS_CTRL); + + /* De-assert Phy SW Reset */ + val = readl(qphy->base + PCIE2_PHY_RESET_CTRL); + val &= ~BIT(0); + writel(val, qphy->base + PCIE2_PHY_RESET_CTRL); + + usleep_range(1000, 2000); + + ret = reset_control_deassert(qphy->pipe_reset); + if (ret) { + dev_err(qphy->dev, "cannot deassert pipe reset\n"); + goto out; + } + + clk_set_rate(qphy->pipe_clk, 250000000); + + ret = clk_prepare_enable(qphy->pipe_clk); + if (ret) { + dev_err(qphy->dev, "failed to enable pipe clock\n"); + goto out; + } + + ret = readl_poll_timeout(qphy->base + PCIE20_PARF_PHY_STTS, val, + !(val & BIT(0)), 1000, 10); + if (ret) + dev_err(qphy->dev, "phy initialization failed\n"); + +out: + return ret; +} + +static int qcom_pcie2_phy_power_off(struct phy *phy) +{ + struct qcom_phy *qphy = phy_get_drvdata(phy); + u32 val; + + val = readl(qphy->base + PCIE2_PHY_RESET_CTRL); + val |= BIT(0); + writel(val, qphy->base + PCIE2_PHY_RESET_CTRL); + + clk_disable_unprepare(qphy->pipe_clk); + reset_control_assert(qphy->pipe_reset); + + return 0; +} + +static int qcom_pcie2_phy_exit(struct phy *phy) +{ + struct qcom_phy *qphy = phy_get_drvdata(phy); + + regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs); + reset_control_assert(qphy->phy_reset); + + return 0; +} + +static const struct phy_ops qcom_pcie2_ops = { + .init = qcom_pcie2_phy_init, + .power_on = qcom_pcie2_phy_power_on, + .power_off = qcom_pcie2_phy_power_off, + .exit = qcom_pcie2_phy_exit, + .owner = THIS_MODULE, +}; + +/* + * Register a fixed rate pipe clock. + * + * The <s>_pipe_clksrc generated by PHY goes to the GCC that gate + * controls it. The <s>_pipe_clk coming out of the GCC is requested + * by the PHY driver for its operations. + * We register the <s>_pipe_clksrc here. The gcc driver takes care + * of assigning this <s>_pipe_clksrc as parent to <s>_pipe_clk. + * Below picture shows this relationship. + * + * +---------------+ + * | PHY block |<<---------------------------------------+ + * | | | + * | +-------+ | +-----+ | + * I/P---^-->| PLL |---^--->pipe_clksrc--->| GCC |--->pipe_clk---+ + * clk | +-------+ | +-----+ + * +---------------+ + */ +static int phy_pipe_clksrc_register(struct qcom_phy *qphy) +{ + struct device_node *np = qphy->dev->of_node; + struct clk_fixed_rate *fixed; + struct clk_init_data init = { }; + int ret; + + ret = of_property_read_string(np, "clock-output-names", &init.name); + if (ret) { + dev_err(qphy->dev, "%s: No clock-output-names\n", np->name); + return ret; + } + + fixed = devm_kzalloc(qphy->dev, sizeof(*fixed), GFP_KERNEL); + if (!fixed) + return -ENOMEM; + + init.ops = &clk_fixed_rate_ops; + + /* controllers using QMP phys use 250MHz pipe clock interface */ + fixed->fixed_rate = 250000000; + fixed->hw.init = &init; + + return devm_clk_hw_register(qphy->dev, &fixed->hw); +} + +static int qcom_pcie2_phy_probe(struct platform_device *pdev) +{ + struct phy_provider *phy_provider; + struct qcom_phy *qphy; + struct resource *res; + struct device *dev = &pdev->dev; + struct phy *phy; + int ret; + + qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL); + if (!qphy) + return -ENOMEM; + + qphy->dev = dev; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + qphy->base = devm_ioremap_resource(dev, res); + if (IS_ERR(qphy->base)) + return PTR_ERR(qphy->base); + + ret = phy_pipe_clksrc_register(qphy); + if (ret) { + dev_err(dev, "failed to register pipe_clk\n"); + return ret; + } + + qphy->vregs[0].supply = "vdda-vp"; + qphy->vregs[1].supply = "vdda-vph"; + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(qphy->vregs), qphy->vregs); + if (ret < 0) + return ret; + + qphy->pipe_clk = devm_clk_get(dev, NULL); + if (IS_ERR(qphy->pipe_clk)) { + dev_err(dev, "failed to acquire pipe clock\n"); + return PTR_ERR(qphy->pipe_clk); + } + + qphy->phy_reset = devm_reset_control_get_exclusive(dev, "phy"); + if (IS_ERR(qphy->phy_reset)) { + dev_err(dev, "failed to acquire phy reset\n"); + return PTR_ERR(qphy->phy_reset); + } + + qphy->pipe_reset = devm_reset_control_get_exclusive(dev, "pipe"); + if (IS_ERR(qphy->pipe_reset)) { + dev_err(dev, "failed to acquire pipe reset\n"); + return PTR_ERR(qphy->pipe_reset); + } + + phy = devm_phy_create(dev, dev->of_node, &qcom_pcie2_ops); + if (IS_ERR(phy)) { + dev_err(dev, "failed to create phy\n"); + return PTR_ERR(phy); + } + + phy_set_drvdata(phy, qphy); + + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); + if (IS_ERR(phy_provider)) + dev_err(dev, "failed to register phy provider\n"); + + return PTR_ERR_OR_ZERO(phy_provider); +} + +static const struct of_device_id qcom_pcie2_phy_match_table[] = { + { .compatible = "qcom,pcie2-phy" }, + {} +}; +MODULE_DEVICE_TABLE(of, qcom_pcie2_phy_match_table); + +static struct platform_driver qcom_pcie2_phy_driver = { + .probe = qcom_pcie2_phy_probe, + .driver = { + .name = "phy-qcom-pcie2", + .of_match_table = qcom_pcie2_phy_match_table, + }, +}; + +module_platform_driver(qcom_pcie2_phy_driver); + +MODULE_DESCRIPTION("Qualcomm PCIe PHY driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c index 08d6f6f7f039..34ff6434da8f 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp.c +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c @@ -242,6 +242,88 @@ static const struct qmp_phy_init_tbl msm8996_pcie_pcs_tbl[] = { QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M3P5DB_V0, 0x0e), }; +static const struct qmp_phy_init_tbl msm8998_pcie_serdes_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x14), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_RESETSM_CNTRL, 0x20), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE0, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE0, 0xc9), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_TIMER1, 0xff), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_TIMER2, 0x3f), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_EP_DIV, 0x19), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_ENABLE1, 0x90), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x82), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x03), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0x55), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0x55), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x0d), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x08), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x34), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x33), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_BUF_ENABLE, 0x07), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_BG_TIMER, 0x09), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_EN_CENTER, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER1, 0x40), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER2, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER1, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER2, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE1, 0x7e), + QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE2, 0x15), +}; + +static const struct qmp_phy_init_tbl msm8998_pcie_tx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V3_TX_RCV_DETECT_LVL_2, 0x12), + QMP_PHY_INIT_CFG(QSERDES_V3_TX_HIGHZ_DRVR_EN, 0x10), + QMP_PHY_INIT_CFG(QSERDES_V3_TX_LANE_MODE_1, 0x06), +}; + +static const struct qmp_phy_init_tbl msm8998_pcie_rx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x03), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_ENABLES, 0x1c), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x14), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x1a), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x4b), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_GAIN, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_GAIN_HALF, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_INTERFACE_MODE, 0x40), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_PI_CONTROLS, 0x71), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_COUNT_LOW, 0x40), +}; + +static const struct qmp_phy_init_tbl msm8998_pcie_pcs_tbl[] = { + QMP_PHY_INIT_CFG(QPHY_V3_PCS_ENDPOINT_REFCLK_DRIVE, 0x04), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_OSC_DTCT_ACTIONS, 0x00), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x01), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_L1SS_WAKEUP_DLY_TIME_AUXCLK_MSB, 0x00), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_L1SS_WAKEUP_DLY_TIME_AUXCLK_LSB, 0x20), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_LP_WAKEUP_DLY_TIME_AUXCLK_MSB, 0x00), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_LP_WAKEUP_DLY_TIME_AUXCLK, 0x01), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_PLL_LOCK_CHK_DLY_TIME, 0x73), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_LVL, 0x99), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_SIGDET_CNTRL, 0x03), +}; + static const struct qmp_phy_init_tbl msm8996_usb3_serdes_tbl[] = { QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x14), QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08), @@ -897,6 +979,7 @@ struct qmp_phy { * @init_count: phy common block initialization count * @phy_initialized: indicate if PHY has been initialized * @mode: current PHY mode + * @ufs_reset: optional UFS PHY reset handle */ struct qcom_qmp { struct device *dev; @@ -914,6 +997,8 @@ struct qcom_qmp { int init_count; bool phy_initialized; enum phy_mode mode; + + struct reset_control *ufs_reset; }; static inline void qphy_setbits(void __iomem *base, u32 offset, u32 val) @@ -989,6 +1074,7 @@ static const struct qmp_phy_cfg msm8996_pciephy_cfg = { .start_ctrl = PCS_START | PLL_READY_GATE_EN, .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL, + .mask_pcs_ready = PHYSTATUS, .mask_com_pcs_ready = PCS_READY, .has_phy_com_ctrl = true, @@ -1146,6 +1232,31 @@ static const struct qmp_phy_cfg sdm845_ufsphy_cfg = { .no_pcs_sw_reset = true, }; +static const struct qmp_phy_cfg msm8998_pciephy_cfg = { + .type = PHY_TYPE_PCIE, + .nlanes = 1, + + .serdes_tbl = msm8998_pcie_serdes_tbl, + .serdes_tbl_num = ARRAY_SIZE(msm8998_pcie_serdes_tbl), + .tx_tbl = msm8998_pcie_tx_tbl, + .tx_tbl_num = ARRAY_SIZE(msm8998_pcie_tx_tbl), + .rx_tbl = msm8998_pcie_rx_tbl, + .rx_tbl_num = ARRAY_SIZE(msm8998_pcie_rx_tbl), + .pcs_tbl = msm8998_pcie_pcs_tbl, + .pcs_tbl_num = ARRAY_SIZE(msm8998_pcie_pcs_tbl), + .clk_list = msm8996_phy_clk_l, + .num_clks = ARRAY_SIZE(msm8996_phy_clk_l), + .reset_list = ipq8074_pciephy_reset_l, + .num_resets = ARRAY_SIZE(ipq8074_pciephy_reset_l), + .vreg_list = qmp_phy_vreg_l, + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), + .regs = pciephy_regs_layout, + + .start_ctrl = SERDES_START | PCS_START, + .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL, + .mask_pcs_ready = PHYSTATUS, +}; + static const struct qmp_phy_cfg msm8998_usb3phy_cfg = { .type = PHY_TYPE_USB3, .nlanes = 1, @@ -1314,6 +1425,7 @@ static int qcom_qmp_phy_com_exit(struct qcom_qmp *qmp) return 0; } + reset_control_assert(qmp->ufs_reset); if (cfg->has_phy_com_ctrl) { qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL], SERDES_START | PCS_START); @@ -1335,8 +1447,7 @@ static int qcom_qmp_phy_com_exit(struct qcom_qmp *qmp) return 0; } -/* PHY Initialization */ -static int qcom_qmp_phy_init(struct phy *phy) +static int qcom_qmp_phy_enable(struct phy *phy) { struct qmp_phy *qphy = phy_get_drvdata(phy); struct qcom_qmp *qmp = qphy->qmp; @@ -1351,6 +1462,33 @@ static int qcom_qmp_phy_init(struct phy *phy) dev_vdbg(qmp->dev, "Initializing QMP phy\n"); + if (cfg->no_pcs_sw_reset) { + /* + * Get UFS reset, which is delayed until now to avoid a + * circular dependency where UFS needs its PHY, but the PHY + * needs this UFS reset. + */ + if (!qmp->ufs_reset) { + qmp->ufs_reset = + devm_reset_control_get_exclusive(qmp->dev, + "ufsphy"); + + if (IS_ERR(qmp->ufs_reset)) { + ret = PTR_ERR(qmp->ufs_reset); + dev_err(qmp->dev, + "failed to get UFS reset: %d\n", + ret); + + qmp->ufs_reset = NULL; + return ret; + } + } + + ret = reset_control_assert(qmp->ufs_reset); + if (ret) + goto err_lane_rst; + } + ret = qcom_qmp_phy_com_init(qphy); if (ret) return ret; @@ -1383,14 +1521,9 @@ static int qcom_qmp_phy_init(struct phy *phy) cfg->rx_tbl, cfg->rx_tbl_num); qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num); - - /* - * UFS PHY requires the deassert of software reset before serdes start. - * For UFS PHYs that do not have software reset control bits, defer - * starting serdes until the power on callback. - */ - if ((cfg->type == PHY_TYPE_UFS) && cfg->no_pcs_sw_reset) - goto out; + ret = reset_control_deassert(qmp->ufs_reset); + if (ret) + goto err_lane_rst; /* * Pull out PHY from POWER DOWN state. @@ -1403,7 +1536,9 @@ static int qcom_qmp_phy_init(struct phy *phy) usleep_range(cfg->pwrdn_delay_min, cfg->pwrdn_delay_max); /* Pull PHY out of reset state */ - qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET); + if (!cfg->no_pcs_sw_reset) + qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET); + if (cfg->has_phy_dp_com_ctrl) qphy_clrbits(dp_com, QPHY_V3_DP_COM_SW_RESET, SW_RESET); @@ -1413,18 +1548,17 @@ static int qcom_qmp_phy_init(struct phy *phy) status = pcs + cfg->regs[QPHY_PCS_READY_STATUS]; mask = cfg->mask_pcs_ready; - ret = readl_poll_timeout(status, val, !(val & mask), 1, + ret = readl_poll_timeout(status, val, val & mask, 10, PHY_INIT_COMPLETE_TIMEOUT); if (ret) { dev_err(qmp->dev, "phy initialization timed-out\n"); goto err_pcs_ready; } qmp->phy_initialized = true; - -out: - return ret; + return 0; err_pcs_ready: + reset_control_assert(qmp->ufs_reset); clk_disable_unprepare(qphy->pipe_clk); err_clk_enable: if (cfg->has_lane_rst) @@ -1435,7 +1569,7 @@ err_lane_rst: return ret; } -static int qcom_qmp_phy_exit(struct phy *phy) +static int qcom_qmp_phy_disable(struct phy *phy) { struct qmp_phy *qphy = phy_get_drvdata(phy); struct qcom_qmp *qmp = qphy->qmp; @@ -1463,44 +1597,6 @@ static int qcom_qmp_phy_exit(struct phy *phy) return 0; } -static int qcom_qmp_phy_poweron(struct phy *phy) -{ - struct qmp_phy *qphy = phy_get_drvdata(phy); - struct qcom_qmp *qmp = qphy->qmp; - const struct qmp_phy_cfg *cfg = qmp->cfg; - void __iomem *pcs = qphy->pcs; - void __iomem *status; - unsigned int mask, val; - int ret = 0; - - if (cfg->type != PHY_TYPE_UFS) - return 0; - - /* - * For UFS PHY that has not software reset control, serdes start - * should only happen when UFS driver explicitly calls phy_power_on - * after it deasserts software reset. - */ - if (cfg->no_pcs_sw_reset && !qmp->phy_initialized && - (qmp->init_count != 0)) { - /* start SerDes and Phy-Coding-Sublayer */ - qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl); - - status = pcs + cfg->regs[QPHY_PCS_READY_STATUS]; - mask = cfg->mask_pcs_ready; - - ret = readl_poll_timeout(status, val, !(val & mask), 1, - PHY_INIT_COMPLETE_TIMEOUT); - if (ret) { - dev_err(qmp->dev, "phy initialization timed-out\n"); - return ret; - } - qmp->phy_initialized = true; - } - - return ret; -} - static int qcom_qmp_phy_set_mode(struct phy *phy, enum phy_mode mode, int submode) { @@ -1750,9 +1846,15 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np) } static const struct phy_ops qcom_qmp_phy_gen_ops = { - .init = qcom_qmp_phy_init, - .exit = qcom_qmp_phy_exit, - .power_on = qcom_qmp_phy_poweron, + .init = qcom_qmp_phy_enable, + .exit = qcom_qmp_phy_disable, + .set_mode = qcom_qmp_phy_set_mode, + .owner = THIS_MODULE, +}; + +static const struct phy_ops qcom_qmp_ufs_ops = { + .power_on = qcom_qmp_phy_enable, + .power_off = qcom_qmp_phy_disable, .set_mode = qcom_qmp_phy_set_mode, .owner = THIS_MODULE, }; @@ -1763,6 +1865,7 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id) struct qcom_qmp *qmp = dev_get_drvdata(dev); struct phy *generic_phy; struct qmp_phy *qphy; + const struct phy_ops *ops = &qcom_qmp_phy_gen_ops; char prop_name[MAX_PROP_NAME]; int ret; @@ -1849,7 +1952,10 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id) } } - generic_phy = devm_phy_create(dev, np, &qcom_qmp_phy_gen_ops); + if (qmp->cfg->type == PHY_TYPE_UFS) + ops = &qcom_qmp_ufs_ops; + + generic_phy = devm_phy_create(dev, np, ops); if (IS_ERR(generic_phy)) { ret = PTR_ERR(generic_phy); dev_err(dev, "failed to create qphy %d\n", ret); @@ -1873,6 +1979,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = { .compatible = "qcom,msm8996-qmp-usb3-phy", .data = &msm8996_usb3phy_cfg, }, { + .compatible = "qcom,msm8998-qmp-pcie-phy", + .data = &msm8998_pciephy_cfg, + }, { .compatible = "qcom,msm8998-qmp-ufs-phy", .data = &sdm845_ufsphy_cfg, }, { diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h index a1b6cdee9a08..335ea5d7ef40 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp.h +++ b/drivers/phy/qualcomm/phy-qcom-qmp.h @@ -241,6 +241,7 @@ #define QSERDES_V3_RX_RX_BAND 0x110 #define QSERDES_V3_RX_RX_INTERFACE_MODE 0x11c #define QSERDES_V3_RX_RX_MODE_00 0x164 +#define QSERDES_V3_RX_RX_MODE_01 0x168 /* Only for QMP V3 PHY - PCS registers */ #define QPHY_V3_PCS_POWER_DOWN_CONTROL 0x004 @@ -280,6 +281,7 @@ #define QPHY_V3_PCS_TSYNC_RSYNC_TIME 0x08c #define QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK 0x0a0 #define QPHY_V3_PCS_LP_WAKEUP_DLY_TIME_AUXCLK 0x0a4 +#define QPHY_V3_PCS_PLL_LOCK_CHK_DLY_TIME 0x0a8 #define QPHY_V3_PCS_LFPS_TX_ECSTART_EQTLOCK 0x0b0 #define QPHY_V3_PCS_RXEQTRAINING_WAIT_TIME 0x0b8 #define QPHY_V3_PCS_RXEQTRAINING_RUN_TIME 0x0bc @@ -292,13 +294,23 @@ #define QPHY_V3_PCS_RX_MIN_HIBERN8_TIME 0x138 #define QPHY_V3_PCS_RX_SIGDET_CTRL1 0x13c #define QPHY_V3_PCS_RX_SIGDET_CTRL2 0x140 +#define QPHY_V3_PCS_LP_WAKEUP_DLY_TIME_AUXCLK_MSB 0x1a8 +#define QPHY_V3_PCS_OSC_DTCT_ACTIONS 0x1ac +#define QPHY_V3_PCS_SIGDET_CNTRL 0x1b0 #define QPHY_V3_PCS_TX_MID_TERM_CTRL1 0x1bc #define QPHY_V3_PCS_MULTI_LANE_CTRL1 0x1c4 #define QPHY_V3_PCS_RX_SIGDET_LVL 0x1d8 +#define QPHY_V3_PCS_L1SS_WAKEUP_DLY_TIME_AUXCLK_LSB 0x1dc +#define QPHY_V3_PCS_L1SS_WAKEUP_DLY_TIME_AUXCLK_MSB 0x1e0 #define QPHY_V3_PCS_REFGEN_REQ_CONFIG1 0x20c #define QPHY_V3_PCS_REFGEN_REQ_CONFIG2 0x210 /* Only for QMP V3 PHY - PCS_MISC registers */ #define QPHY_V3_PCS_MISC_CLAMP_ENABLE 0x0c +#define QPHY_V3_PCS_MISC_OSC_DTCT_CONFIG2 0x2c +#define QPHY_V3_PCS_MISC_PCIE_INT_AUX_CLK_CONFIG1 0x44 +#define QPHY_V3_PCS_MISC_OSC_DTCT_MODE2_CONFIG2 0x54 +#define QPHY_V3_PCS_MISC_OSC_DTCT_MODE2_CONFIG4 0x5c +#define QPHY_V3_PCS_MISC_OSC_DTCT_MODE2_CONFIG5 0x60 #endif diff --git a/drivers/phy/qualcomm/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c index 8fd7ce139772..bf94a52d3087 100644 --- a/drivers/phy/qualcomm/phy-qcom-qusb2.c +++ b/drivers/phy/qualcomm/phy-qcom-qusb2.c @@ -564,7 +564,7 @@ static int __maybe_unused qusb2_phy_runtime_resume(struct device *dev) } if (!qphy->has_se_clk_scheme) { - clk_prepare_enable(qphy->ref_clk); + ret = clk_prepare_enable(qphy->ref_clk); if (ret) { dev_err(dev, "failed to enable ref clk, %d\n", ret); goto disable_ahb_clk; @@ -822,14 +822,9 @@ static int qusb2_phy_probe(struct platform_device *pdev) return ret; } - qphy->iface_clk = devm_clk_get(dev, "iface"); - if (IS_ERR(qphy->iface_clk)) { - ret = PTR_ERR(qphy->iface_clk); - if (ret == -EPROBE_DEFER) - return ret; - qphy->iface_clk = NULL; - dev_dbg(dev, "failed to get iface clk, %d\n", ret); - } + qphy->iface_clk = devm_clk_get_optional(dev, "iface"); + if (IS_ERR(qphy->iface_clk)) + return PTR_ERR(qphy->iface_clk); qphy->phy_reset = devm_reset_control_get_by_index(&pdev->dev, 0); if (IS_ERR(qphy->phy_reset)) { diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-i.h b/drivers/phy/qualcomm/phy-qcom-ufs-i.h index f798fb64de94..9bf973a0d8c3 100644 --- a/drivers/phy/qualcomm/phy-qcom-ufs-i.h +++ b/drivers/phy/qualcomm/phy-qcom-ufs-i.h @@ -1,15 +1,6 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ /* * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 and - * only version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * */ #ifndef UFS_QCOM_PHY_I_H_ @@ -19,6 +10,7 @@ #include <linux/clk.h> #include <linux/phy/phy.h> #include <linux/regulator/consumer.h> +#include <linux/reset.h> #include <linux/slab.h> #include <linux/platform_device.h> #include <linux/io.h> @@ -96,11 +88,10 @@ struct ufs_qcom_phy { char name[UFS_QCOM_PHY_NAME_LEN]; struct ufs_qcom_phy_calibration *cached_regs; int cached_regs_table_size; - bool is_powered_on; - bool is_started; struct ufs_qcom_phy_specific_ops *phy_spec_ops; enum phy_mode mode; + struct reset_control *ufs_reset; }; /** @@ -115,6 +106,7 @@ struct ufs_qcom_phy { * and writes to QSERDES_RX_SIGDET_CNTRL attribute */ struct ufs_qcom_phy_specific_ops { + int (*calibrate)(struct ufs_qcom_phy *ufs_qcom_phy, bool is_rate_B); void (*start_serdes)(struct ufs_qcom_phy *phy); int (*is_physical_coding_sublayer_ready)(struct ufs_qcom_phy *phy); void (*set_tx_lane_enable)(struct ufs_qcom_phy *phy, u32 val); diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c index 1e0d4f2046a4..54b355bfc24c 100644 --- a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c +++ b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c @@ -1,15 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-only /* * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 and - * only version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * */ #include "phy-qcom-ufs-qmp-14nm.h" @@ -42,28 +33,6 @@ void ufs_qcom_phy_qmp_14nm_advertise_quirks(struct ufs_qcom_phy *phy_common) UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE; } -static int ufs_qcom_phy_qmp_14nm_init(struct phy *generic_phy) -{ - struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy); - bool is_rate_B = false; - int ret; - - if (phy_common->mode == PHY_MODE_UFS_HS_B) - is_rate_B = true; - - ret = ufs_qcom_phy_qmp_14nm_phy_calibrate(phy_common, is_rate_B); - if (!ret) - /* phy calibrated, but yet to be started */ - phy_common->is_started = false; - - return ret; -} - -static int ufs_qcom_phy_qmp_14nm_exit(struct phy *generic_phy) -{ - return 0; -} - static int ufs_qcom_phy_qmp_14nm_set_mode(struct phy *generic_phy, enum phy_mode mode, int submode) @@ -124,8 +93,6 @@ static int ufs_qcom_phy_qmp_14nm_is_pcs_ready(struct ufs_qcom_phy *phy_common) } static const struct phy_ops ufs_qcom_phy_qmp_14nm_phy_ops = { - .init = ufs_qcom_phy_qmp_14nm_init, - .exit = ufs_qcom_phy_qmp_14nm_exit, .power_on = ufs_qcom_phy_power_on, .power_off = ufs_qcom_phy_power_off, .set_mode = ufs_qcom_phy_qmp_14nm_set_mode, @@ -133,6 +100,7 @@ static const struct phy_ops ufs_qcom_phy_qmp_14nm_phy_ops = { }; static struct ufs_qcom_phy_specific_ops phy_14nm_ops = { + .calibrate = ufs_qcom_phy_qmp_14nm_phy_calibrate, .start_serdes = ufs_qcom_phy_qmp_14nm_start_serdes, .is_physical_coding_sublayer_ready = ufs_qcom_phy_qmp_14nm_is_pcs_ready, .set_tx_lane_enable = ufs_qcom_phy_qmp_14nm_set_tx_lane_enable, diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h index 3aefdbacbcd0..ceca654b9338 100644 --- a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h +++ b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h @@ -1,15 +1,6 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ /* * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 and - * only version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * */ #ifndef UFS_QCOM_PHY_QMP_14NM_H_ diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c index aef40f7a41d4..3e9d8b71e995 100644 --- a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c +++ b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c @@ -1,15 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-only /* * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 and - * only version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * */ #include "phy-qcom-ufs-qmp-20nm.h" @@ -61,28 +52,6 @@ void ufs_qcom_phy_qmp_20nm_advertise_quirks(struct ufs_qcom_phy *phy_common) UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE; } -static int ufs_qcom_phy_qmp_20nm_init(struct phy *generic_phy) -{ - struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy); - bool is_rate_B = false; - int ret; - - if (phy_common->mode == PHY_MODE_UFS_HS_B) - is_rate_B = true; - - ret = ufs_qcom_phy_qmp_20nm_phy_calibrate(phy_common, is_rate_B); - if (!ret) - /* phy calibrated, but yet to be started */ - phy_common->is_started = false; - - return ret; -} - -static int ufs_qcom_phy_qmp_20nm_exit(struct phy *generic_phy) -{ - return 0; -} - static int ufs_qcom_phy_qmp_20nm_set_mode(struct phy *generic_phy, enum phy_mode mode, int submode) @@ -182,8 +151,6 @@ static int ufs_qcom_phy_qmp_20nm_is_pcs_ready(struct ufs_qcom_phy *phy_common) } static const struct phy_ops ufs_qcom_phy_qmp_20nm_phy_ops = { - .init = ufs_qcom_phy_qmp_20nm_init, - .exit = ufs_qcom_phy_qmp_20nm_exit, .power_on = ufs_qcom_phy_power_on, .power_off = ufs_qcom_phy_power_off, .set_mode = ufs_qcom_phy_qmp_20nm_set_mode, @@ -191,6 +158,7 @@ static const struct phy_ops ufs_qcom_phy_qmp_20nm_phy_ops = { }; static struct ufs_qcom_phy_specific_ops phy_20nm_ops = { + .calibrate = ufs_qcom_phy_qmp_20nm_phy_calibrate, .start_serdes = ufs_qcom_phy_qmp_20nm_start_serdes, .is_physical_coding_sublayer_ready = ufs_qcom_phy_qmp_20nm_is_pcs_ready, .set_tx_lane_enable = ufs_qcom_phy_qmp_20nm_set_tx_lane_enable, diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h index 4f3076bb3d71..8ce79f524eed 100644 --- a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h +++ b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h @@ -1,15 +1,6 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ /* * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 and - * only version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * */ #ifndef UFS_QCOM_PHY_QMP_20NM_H_ diff --git a/drivers/phy/qualcomm/phy-qcom-ufs.c b/drivers/phy/qualcomm/phy-qcom-ufs.c index f2979ccad00a..763c8d396af1 100644 --- a/drivers/phy/qualcomm/phy-qcom-ufs.c +++ b/drivers/phy/qualcomm/phy-qcom-ufs.c @@ -1,15 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-only /* * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 and - * only version 2 as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * */ #include "phy-qcom-ufs-i.h" @@ -147,6 +138,21 @@ out: } EXPORT_SYMBOL_GPL(ufs_qcom_phy_generic_probe); +static int ufs_qcom_phy_get_reset(struct ufs_qcom_phy *phy_common) +{ + struct reset_control *reset; + + if (phy_common->ufs_reset) + return 0; + + reset = devm_reset_control_get_exclusive_by_index(phy_common->dev, 0); + if (IS_ERR(reset)) + return PTR_ERR(reset); + + phy_common->ufs_reset = reset; + return 0; +} + static int __ufs_qcom_phy_clk_get(struct device *dev, const char *name, struct clk **clk_out, bool err_print) { @@ -459,7 +465,7 @@ out: } /* Turn OFF M-PHY RMMI interface clocks */ -void ufs_qcom_phy_disable_iface_clk(struct ufs_qcom_phy *phy) +static void ufs_qcom_phy_disable_iface_clk(struct ufs_qcom_phy *phy) { if (phy->is_iface_clk_enabled) { clk_disable_unprepare(phy->tx_iface_clk); @@ -528,23 +534,38 @@ int ufs_qcom_phy_power_on(struct phy *generic_phy) { struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy); struct device *dev = phy_common->dev; + bool is_rate_B = false; int err; - if (phy_common->is_powered_on) - return 0; + err = ufs_qcom_phy_get_reset(phy_common); + if (err) + return err; - if (!phy_common->is_started) { - err = ufs_qcom_phy_start_serdes(phy_common); - if (err) - return err; + err = reset_control_assert(phy_common->ufs_reset); + if (err) + return err; - err = ufs_qcom_phy_is_pcs_ready(phy_common); - if (err) - return err; + if (phy_common->mode == PHY_MODE_UFS_HS_B) + is_rate_B = true; - phy_common->is_started = true; + err = phy_common->phy_spec_ops->calibrate(phy_common, is_rate_B); + if (err) + return err; + + err = reset_control_deassert(phy_common->ufs_reset); + if (err) { + dev_err(dev, "Failed to assert UFS PHY reset"); + return err; } + err = ufs_qcom_phy_start_serdes(phy_common); + if (err) + return err; + + err = ufs_qcom_phy_is_pcs_ready(phy_common); + if (err) + return err; + err = ufs_qcom_phy_enable_vreg(dev, &phy_common->vdda_phy); if (err) { dev_err(dev, "%s enable vdda_phy failed, err=%d\n", @@ -587,7 +608,6 @@ int ufs_qcom_phy_power_on(struct phy *generic_phy) } } - phy_common->is_powered_on = true; goto out; out_disable_ref_clk: @@ -607,9 +627,6 @@ int ufs_qcom_phy_power_off(struct phy *generic_phy) { struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy); - if (!phy_common->is_powered_on) - return 0; - phy_common->phy_spec_ops->power_control(phy_common, false); if (phy_common->vddp_ref_clk.reg) @@ -620,8 +637,7 @@ int ufs_qcom_phy_power_off(struct phy *generic_phy) ufs_qcom_phy_disable_vreg(phy_common->dev, &phy_common->vdda_pll); ufs_qcom_phy_disable_vreg(phy_common->dev, &phy_common->vdda_phy); - phy_common->is_powered_on = false; - + reset_control_assert(phy_common->ufs_reset); return 0; } EXPORT_SYMBOL_GPL(ufs_qcom_phy_power_off); diff --git a/drivers/phy/qualcomm/phy-qcom-usb-hs.c b/drivers/phy/qualcomm/phy-qcom-usb-hs.c index 04934f8dac91..b163b3a1558d 100644 --- a/drivers/phy/qualcomm/phy-qcom-usb-hs.c +++ b/drivers/phy/qualcomm/phy-qcom-usb-hs.c @@ -1,9 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-only /** * Copyright (C) 2016 Linaro Ltd - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. */ #include <linux/module.h> #include <linux/ulpi/driver.h> diff --git a/drivers/phy/qualcomm/phy-qcom-usb-hsic.c b/drivers/phy/qualcomm/phy-qcom-usb-hsic.c index c110563a73cb..04d18d52f700 100644 --- a/drivers/phy/qualcomm/phy-qcom-usb-hsic.c +++ b/drivers/phy/qualcomm/phy-qcom-usb-hsic.c @@ -1,9 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-only /** * Copyright (C) 2016 Linaro Ltd - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. */ #include <linux/module.h> #include <linux/ulpi/driver.h> |