diff options
Diffstat (limited to 'drivers/phy')
29 files changed, 1873 insertions, 50 deletions
diff --git a/drivers/phy/allwinner/Kconfig b/drivers/phy/allwinner/Kconfig index 215425296c77..3dab79e9d52b 100644 --- a/drivers/phy/allwinner/Kconfig +++ b/drivers/phy/allwinner/Kconfig @@ -45,3 +45,14 @@ config PHY_SUN9I_USB sun9i SoCs. This driver controls each individual USB 2 host PHY. + +config PHY_SUN50I_USB3 + tristate "Allwinner H6 SoC USB3 PHY driver" + depends on ARCH_SUNXI && HAS_IOMEM && OF + depends on RESET_CONTROLLER + select GENERIC_PHY + help + Enable this to support the USB3.0-capable transceiver that is + part of Allwinner H6 SoC. + + This driver controls each individual USB 2+3 host PHY combo. diff --git a/drivers/phy/allwinner/Makefile b/drivers/phy/allwinner/Makefile index 799a65c0b58d..bd74901a1255 100644 --- a/drivers/phy/allwinner/Makefile +++ b/drivers/phy/allwinner/Makefile @@ -2,3 +2,4 @@ obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o obj-$(CONFIG_PHY_SUN6I_MIPI_DPHY) += phy-sun6i-mipi-dphy.o obj-$(CONFIG_PHY_SUN9I_USB) += phy-sun9i-usb.o +obj-$(CONFIG_PHY_SUN50I_USB3) += phy-sun50i-usb3.o diff --git a/drivers/phy/allwinner/phy-sun50i-usb3.c b/drivers/phy/allwinner/phy-sun50i-usb3.c new file mode 100644 index 000000000000..1169f3e83a6f --- /dev/null +++ b/drivers/phy/allwinner/phy-sun50i-usb3.c @@ -0,0 +1,190 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Allwinner sun50i(H6) USB 3.0 phy driver + * + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> + * + * Based on phy-sun9i-usb.c, which is: + * + * Copyright (C) 2014-2015 Chen-Yu Tsai <wens@csie.org> + * + * Based on code from Allwinner BSP, which is: + * + * Copyright (c) 2010-2015 Allwinner Technology Co., Ltd. + */ + +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/phy/phy.h> +#include <linux/platform_device.h> +#include <linux/reset.h> + +/* Interface Status and Control Registers */ +#define SUNXI_ISCR 0x00 +#define SUNXI_PIPE_CLOCK_CONTROL 0x14 +#define SUNXI_PHY_TUNE_LOW 0x18 +#define SUNXI_PHY_TUNE_HIGH 0x1c +#define SUNXI_PHY_EXTERNAL_CONTROL 0x20 + +/* USB2.0 Interface Status and Control Register */ +#define SUNXI_ISCR_FORCE_VBUS (3 << 12) + +/* PIPE Clock Control Register */ +#define SUNXI_PCC_PIPE_CLK_OPEN (1 << 6) + +/* PHY External Control Register */ +#define SUNXI_PEC_EXTERN_VBUS (3 << 1) +#define SUNXI_PEC_SSC_EN (1 << 24) +#define SUNXI_PEC_REF_SSP_EN (1 << 26) + +/* PHY Tune High Register */ +#define SUNXI_TX_DEEMPH_3P5DB(n) ((n) << 19) +#define SUNXI_TX_DEEMPH_3P5DB_MASK GENMASK(24, 19) +#define SUNXI_TX_DEEMPH_6DB(n) ((n) << 13) +#define SUNXI_TX_DEEMPH_6GB_MASK GENMASK(18, 13) +#define SUNXI_TX_SWING_FULL(n) ((n) << 6) +#define SUNXI_TX_SWING_FULL_MASK GENMASK(12, 6) +#define SUNXI_LOS_BIAS(n) ((n) << 3) +#define SUNXI_LOS_BIAS_MASK GENMASK(5, 3) +#define SUNXI_TXVBOOSTLVL(n) ((n) << 0) +#define SUNXI_TXVBOOSTLVL_MASK GENMASK(0, 2) + +struct sun50i_usb3_phy { + struct phy *phy; + void __iomem *regs; + struct reset_control *reset; + struct clk *clk; +}; + +static void sun50i_usb3_phy_open(struct sun50i_usb3_phy *phy) +{ + u32 val; + + val = readl(phy->regs + SUNXI_PHY_EXTERNAL_CONTROL); + val |= SUNXI_PEC_EXTERN_VBUS; + val |= SUNXI_PEC_SSC_EN | SUNXI_PEC_REF_SSP_EN; + writel(val, phy->regs + SUNXI_PHY_EXTERNAL_CONTROL); + + val = readl(phy->regs + SUNXI_PIPE_CLOCK_CONTROL); + val |= SUNXI_PCC_PIPE_CLK_OPEN; + writel(val, phy->regs + SUNXI_PIPE_CLOCK_CONTROL); + + val = readl(phy->regs + SUNXI_ISCR); + val |= SUNXI_ISCR_FORCE_VBUS; + writel(val, phy->regs + SUNXI_ISCR); + + /* + * All the magic numbers written to the PHY_TUNE_{LOW_HIGH} + * registers are directly taken from the BSP USB3 driver from + * Allwiner. + */ + writel(0x0047fc87, phy->regs + SUNXI_PHY_TUNE_LOW); + + val = readl(phy->regs + SUNXI_PHY_TUNE_HIGH); + val &= ~(SUNXI_TXVBOOSTLVL_MASK | SUNXI_LOS_BIAS_MASK | + SUNXI_TX_SWING_FULL_MASK | SUNXI_TX_DEEMPH_6GB_MASK | + SUNXI_TX_DEEMPH_3P5DB_MASK); + val |= SUNXI_TXVBOOSTLVL(0x7); + val |= SUNXI_LOS_BIAS(0x7); + val |= SUNXI_TX_SWING_FULL(0x55); + val |= SUNXI_TX_DEEMPH_6DB(0x20); + val |= SUNXI_TX_DEEMPH_3P5DB(0x15); + writel(val, phy->regs + SUNXI_PHY_TUNE_HIGH); +} + +static int sun50i_usb3_phy_init(struct phy *_phy) +{ + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy); + int ret; + + ret = clk_prepare_enable(phy->clk); + if (ret) + return ret; + + ret = reset_control_deassert(phy->reset); + if (ret) { + clk_disable_unprepare(phy->clk); + return ret; + } + + sun50i_usb3_phy_open(phy); + return 0; +} + +static int sun50i_usb3_phy_exit(struct phy *_phy) +{ + struct sun50i_usb3_phy *phy = phy_get_drvdata(_phy); + + reset_control_assert(phy->reset); + clk_disable_unprepare(phy->clk); + + return 0; +} + +static const struct phy_ops sun50i_usb3_phy_ops = { + .init = sun50i_usb3_phy_init, + .exit = sun50i_usb3_phy_exit, + .owner = THIS_MODULE, +}; + +static int sun50i_usb3_phy_probe(struct platform_device *pdev) +{ + struct sun50i_usb3_phy *phy; + struct device *dev = &pdev->dev; + struct phy_provider *phy_provider; + struct resource *res; + + phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL); + if (!phy) + return -ENOMEM; + + phy->clk = devm_clk_get(dev, NULL); + if (IS_ERR(phy->clk)) { + if (PTR_ERR(phy->clk) != -EPROBE_DEFER) + dev_err(dev, "failed to get phy clock\n"); + return PTR_ERR(phy->clk); + } + + phy->reset = devm_reset_control_get(dev, NULL); + if (IS_ERR(phy->reset)) { + dev_err(dev, "failed to get reset control\n"); + return PTR_ERR(phy->reset); + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + phy->regs = devm_ioremap_resource(dev, res); + if (IS_ERR(phy->regs)) + return PTR_ERR(phy->regs); + + phy->phy = devm_phy_create(dev, NULL, &sun50i_usb3_phy_ops); + if (IS_ERR(phy->phy)) { + dev_err(dev, "failed to create PHY\n"); + return PTR_ERR(phy->phy); + } + + phy_set_drvdata(phy->phy, phy); + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); + + return PTR_ERR_OR_ZERO(phy_provider); +} + +static const struct of_device_id sun50i_usb3_phy_of_match[] = { + { .compatible = "allwinner,sun50i-h6-usb3-phy" }, + { }, +}; +MODULE_DEVICE_TABLE(of, sun50i_usb3_phy_of_match); + +static struct platform_driver sun50i_usb3_phy_driver = { + .probe = sun50i_usb3_phy_probe, + .driver = { + .of_match_table = sun50i_usb3_phy_of_match, + .name = "sun50i-usb3-phy", + } +}; +module_platform_driver(sun50i_usb3_phy_driver); + +MODULE_DESCRIPTION("Allwinner H6 USB 3.0 phy driver"); +MODULE_AUTHOR("Icenowy Zheng <icenowy@aosc.io>"); +MODULE_LICENSE("GPL"); diff --git a/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c b/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c index ac322d643c7a..08e322789e59 100644 --- a/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c +++ b/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c @@ -50,6 +50,8 @@ #define PHY_R5_PHY_CR_ACK BIT(16) #define PHY_R5_PHY_BS_OUT BIT(17) +#define PCIE_RESET_DELAY 500 + struct phy_g12a_usb3_pcie_priv { struct regmap *regmap; struct regmap *regmap_cr; @@ -196,6 +198,10 @@ static int phy_g12a_usb3_init(struct phy *phy) struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); int data, ret; + ret = reset_control_reset(priv->reset); + if (ret) + return ret; + /* Switch PHY to USB3 */ /* TODO figure out how to handle when PCIe was set in the bootloader */ regmap_update_bits(priv->regmap, PHY_R0, @@ -272,24 +278,64 @@ static int phy_g12a_usb3_init(struct phy *phy) return 0; } -static int phy_g12a_usb3_pcie_init(struct phy *phy) +static int phy_g12a_usb3_pcie_power_on(struct phy *phy) +{ + struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); + + if (priv->mode == PHY_TYPE_USB3) + return 0; + + regmap_update_bits(priv->regmap, PHY_R0, + PHY_R0_PCIE_POWER_STATE, + FIELD_PREP(PHY_R0_PCIE_POWER_STATE, 0x1c)); + + return 0; +} + +static int phy_g12a_usb3_pcie_power_off(struct phy *phy) +{ + struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); + + if (priv->mode == PHY_TYPE_USB3) + return 0; + + regmap_update_bits(priv->regmap, PHY_R0, + PHY_R0_PCIE_POWER_STATE, + FIELD_PREP(PHY_R0_PCIE_POWER_STATE, 0x1d)); + + return 0; +} + +static int phy_g12a_usb3_pcie_reset(struct phy *phy) { struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); int ret; - ret = reset_control_reset(priv->reset); + if (priv->mode == PHY_TYPE_USB3) + return 0; + + ret = reset_control_assert(priv->reset); if (ret) return ret; + udelay(PCIE_RESET_DELAY); + + ret = reset_control_deassert(priv->reset); + if (ret) + return ret; + + udelay(PCIE_RESET_DELAY); + + return 0; +} + +static int phy_g12a_usb3_pcie_init(struct phy *phy) +{ + struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); + if (priv->mode == PHY_TYPE_USB3) return phy_g12a_usb3_init(phy); - /* Power UP PCIE */ - /* TODO figure out when the bootloader has set USB3 mode before */ - regmap_update_bits(priv->regmap, PHY_R0, - PHY_R0_PCIE_POWER_STATE, - FIELD_PREP(PHY_R0_PCIE_POWER_STATE, 0x1c)); - return 0; } @@ -297,7 +343,10 @@ static int phy_g12a_usb3_pcie_exit(struct phy *phy) { struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); - return reset_control_reset(priv->reset); + if (priv->mode == PHY_TYPE_USB3) + return reset_control_reset(priv->reset); + + return 0; } static struct phy *phy_g12a_usb3_pcie_xlate(struct device *dev, @@ -326,6 +375,9 @@ static struct phy *phy_g12a_usb3_pcie_xlate(struct device *dev, static const struct phy_ops phy_g12a_usb3_pcie_ops = { .init = phy_g12a_usb3_pcie_init, .exit = phy_g12a_usb3_pcie_exit, + .power_on = phy_g12a_usb3_pcie_power_on, + .power_off = phy_g12a_usb3_pcie_power_off, + .reset = phy_g12a_usb3_pcie_reset, .owner = THIS_MODULE, }; diff --git a/drivers/phy/broadcom/phy-brcm-usb-init.c b/drivers/phy/broadcom/phy-brcm-usb-init.c index 3c53625f8bc2..91b5b09589d6 100644 --- a/drivers/phy/broadcom/phy-brcm-usb-init.c +++ b/drivers/phy/broadcom/phy-brcm-usb-init.c @@ -126,8 +126,8 @@ enum { USB_CTRL_SELECTOR_COUNT, }; -#define USB_CTRL_REG(base, reg) ((void *)base + USB_CTRL_##reg) -#define USB_XHCI_EC_REG(base, reg) ((void *)base + USB_XHCI_EC_##reg) +#define USB_CTRL_REG(base, reg) ((void __iomem *)base + USB_CTRL_##reg) +#define USB_XHCI_EC_REG(base, reg) ((void __iomem *)base + USB_XHCI_EC_##reg) #define USB_CTRL_MASK(reg, field) \ USB_CTRL_##reg##_##field##_MASK #define USB_CTRL_MASK_FAMILY(params, reg, field) \ @@ -416,7 +416,7 @@ void usb_ctrl_unset_family(struct brcm_usb_init_params *params, u32 reg_offset, u32 field) { u32 mask; - void *reg; + void __iomem *reg; mask = params->usb_reg_bits_map[field]; reg = params->ctrl_regs + reg_offset; @@ -428,7 +428,7 @@ void usb_ctrl_set_family(struct brcm_usb_init_params *params, u32 reg_offset, u32 field) { u32 mask; - void *reg; + void __iomem *reg; mask = params->usb_reg_bits_map[field]; reg = params->ctrl_regs + reg_offset; @@ -707,7 +707,7 @@ static void brcmusb_usb3_otp_fix(struct brcm_usb_init_params *params) void __iomem *xhci_ec_base = params->xhci_ec_regs; u32 val; - if (params->family_id != 0x74371000 || xhci_ec_base == 0) + if (params->family_id != 0x74371000 || !xhci_ec_base) return; brcmusb_writel(0xa20c, USB_XHCI_EC_REG(xhci_ec_base, IRAADR)); val = brcmusb_readl(USB_XHCI_EC_REG(xhci_ec_base, IRADAT)); diff --git a/drivers/phy/hisilicon/phy-hisi-inno-usb2.c b/drivers/phy/hisilicon/phy-hisi-inno-usb2.c index 9b16f13b5ab2..34a6a9a1ceb2 100644 --- a/drivers/phy/hisilicon/phy-hisi-inno-usb2.c +++ b/drivers/phy/hisilicon/phy-hisi-inno-usb2.c @@ -114,7 +114,6 @@ static int hisi_inno_phy_probe(struct platform_device *pdev) struct hisi_inno_phy_priv *priv; struct phy_provider *provider; struct device_node *child; - struct resource *res; int i = 0; int ret; @@ -122,8 +121,7 @@ static int hisi_inno_phy_probe(struct platform_device *pdev) if (!priv) return -ENOMEM; - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - priv->mmio = devm_ioremap_resource(dev, res); + priv->mmio = devm_platform_ioremap_resource(pdev, 0); if (IS_ERR(priv->mmio)) { ret = PTR_ERR(priv->mmio); return ret; diff --git a/drivers/phy/hisilicon/phy-histb-combphy.c b/drivers/phy/hisilicon/phy-histb-combphy.c index 62d10ef20296..f1cb3e4d2add 100644 --- a/drivers/phy/hisilicon/phy-histb-combphy.c +++ b/drivers/phy/hisilicon/phy-histb-combphy.c @@ -195,7 +195,6 @@ static int histb_combphy_probe(struct platform_device *pdev) struct histb_combphy_priv *priv; struct device_node *np = dev->of_node; struct histb_combphy_mode *mode; - struct resource *res; u32 vals[3]; int ret; @@ -203,8 +202,7 @@ static int histb_combphy_probe(struct platform_device *pdev) if (!priv) return -ENOMEM; - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - priv->mmio = devm_ioremap_resource(dev, res); + priv->mmio = devm_platform_ioremap_resource(pdev, 0); if (IS_ERR(priv->mmio)) { ret = PTR_ERR(priv->mmio); return ret; diff --git a/drivers/phy/lantiq/phy-lantiq-vrx200-pcie.c b/drivers/phy/lantiq/phy-lantiq-vrx200-pcie.c index 544d64a84cc0..6e457967653e 100644 --- a/drivers/phy/lantiq/phy-lantiq-vrx200-pcie.c +++ b/drivers/phy/lantiq/phy-lantiq-vrx200-pcie.c @@ -323,7 +323,8 @@ static int ltq_vrx200_pcie_phy_power_on(struct phy *phy) goto err_disable_pdi_clk; /* Check if we are in "startup ready" status */ - if (ltq_vrx200_pcie_phy_wait_for_pll(phy) != 0) + ret = ltq_vrx200_pcie_phy_wait_for_pll(phy); + if (ret) goto err_disable_phy_clk; ltq_vrx200_pcie_phy_apply_workarounds(phy); diff --git a/drivers/phy/marvell/Kconfig b/drivers/phy/marvell/Kconfig index 4053ba6cd0fb..005e02dd4a91 100644 --- a/drivers/phy/marvell/Kconfig +++ b/drivers/phy/marvell/Kconfig @@ -103,3 +103,14 @@ config PHY_PXA_USB The PHY driver will be used by Marvell udc/ehci/otg driver. To compile this driver as a module, choose M here. + +config PHY_MMP3_USB + tristate "Marvell MMP3 USB PHY Driver" + depends on MACH_MMP3_DT || COMPILE_TEST + select GENERIC_PHY + help + Enable this to support Marvell MMP3 USB PHY driver for Marvell + SoC. This driver will do the PHY initialization and shutdown. + The PHY driver will be used by Marvell udc/ehci/otg driver. + + To compile this driver as a module, choose M here. diff --git a/drivers/phy/marvell/Makefile b/drivers/phy/marvell/Makefile index 434eb9ca6cc3..5a106b1549f4 100644 --- a/drivers/phy/marvell/Makefile +++ b/drivers/phy/marvell/Makefile @@ -2,6 +2,7 @@ obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY) += phy-armada375-usb2.o obj-$(CONFIG_PHY_BERLIN_SATA) += phy-berlin-sata.o obj-$(CONFIG_PHY_BERLIN_USB) += phy-berlin-usb.o +obj-$(CONFIG_PHY_MMP3_USB) += phy-mmp3-usb.o obj-$(CONFIG_PHY_MVEBU_A3700_COMPHY) += phy-mvebu-a3700-comphy.o obj-$(CONFIG_PHY_MVEBU_A3700_UTMI) += phy-mvebu-a3700-utmi.o obj-$(CONFIG_PHY_MVEBU_A38X_COMPHY) += phy-armada38x-comphy.o diff --git a/drivers/phy/marvell/phy-mmp3-usb.c b/drivers/phy/marvell/phy-mmp3-usb.c new file mode 100644 index 000000000000..499869595a58 --- /dev/null +++ b/drivers/phy/marvell/phy-mmp3-usb.c @@ -0,0 +1,291 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2011 Marvell International Ltd. All rights reserved. + * Copyright (C) 2018,2019 Lubomir Rintel <lkundrak@v3.sk> + */ + +#include <linux/delay.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/phy/phy.h> +#include <linux/platform_device.h> +#include <linux/soc/mmp/cputype.h> + +#define USB2_PLL_REG0 0x4 +#define USB2_PLL_REG1 0x8 +#define USB2_TX_REG0 0x10 +#define USB2_TX_REG1 0x14 +#define USB2_TX_REG2 0x18 +#define USB2_RX_REG0 0x20 +#define USB2_RX_REG1 0x24 +#define USB2_RX_REG2 0x28 +#define USB2_ANA_REG0 0x30 +#define USB2_ANA_REG1 0x34 +#define USB2_ANA_REG2 0x38 +#define USB2_DIG_REG0 0x3C +#define USB2_DIG_REG1 0x40 +#define USB2_DIG_REG2 0x44 +#define USB2_DIG_REG3 0x48 +#define USB2_TEST_REG0 0x4C +#define USB2_TEST_REG1 0x50 +#define USB2_TEST_REG2 0x54 +#define USB2_CHARGER_REG0 0x58 +#define USB2_OTG_REG0 0x5C +#define USB2_PHY_MON0 0x60 +#define USB2_RESETVE_REG0 0x64 +#define USB2_ICID_REG0 0x78 +#define USB2_ICID_REG1 0x7C + +/* USB2_PLL_REG0 */ + +/* This is for Ax stepping */ +#define USB2_PLL_FBDIV_SHIFT_MMP3 0 +#define USB2_PLL_FBDIV_MASK_MMP3 (0xFF << 0) + +#define USB2_PLL_REFDIV_SHIFT_MMP3 8 +#define USB2_PLL_REFDIV_MASK_MMP3 (0xF << 8) + +#define USB2_PLL_VDD12_SHIFT_MMP3 12 +#define USB2_PLL_VDD18_SHIFT_MMP3 14 + +/* This is for B0 stepping */ +#define USB2_PLL_FBDIV_SHIFT_MMP3_B0 0 +#define USB2_PLL_REFDIV_SHIFT_MMP3_B0 9 +#define USB2_PLL_VDD18_SHIFT_MMP3_B0 14 +#define USB2_PLL_FBDIV_MASK_MMP3_B0 0x01FF +#define USB2_PLL_REFDIV_MASK_MMP3_B0 0x3E00 + +#define USB2_PLL_CAL12_SHIFT_MMP3 0 +#define USB2_PLL_CALI12_MASK_MMP3 (0x3 << 0) + +#define USB2_PLL_VCOCAL_START_SHIFT_MMP3 2 + +#define USB2_PLL_KVCO_SHIFT_MMP3 4 +#define USB2_PLL_KVCO_MASK_MMP3 (0x7<<4) + +#define USB2_PLL_ICP_SHIFT_MMP3 8 +#define USB2_PLL_ICP_MASK_MMP3 (0x7<<8) + +#define USB2_PLL_LOCK_BYPASS_SHIFT_MMP3 12 + +#define USB2_PLL_PU_PLL_SHIFT_MMP3 13 +#define USB2_PLL_PU_PLL_MASK (0x1 << 13) + +#define USB2_PLL_READY_MASK_MMP3 (0x1 << 15) + +/* USB2_TX_REG0 */ +#define USB2_TX_IMPCAL_VTH_SHIFT_MMP3 8 +#define USB2_TX_IMPCAL_VTH_MASK_MMP3 (0x7 << 8) + +#define USB2_TX_RCAL_START_SHIFT_MMP3 13 + +/* USB2_TX_REG1 */ +#define USB2_TX_CK60_PHSEL_SHIFT_MMP3 0 +#define USB2_TX_CK60_PHSEL_MASK_MMP3 (0xf << 0) + +#define USB2_TX_AMP_SHIFT_MMP3 4 +#define USB2_TX_AMP_MASK_MMP3 (0x7 << 4) + +#define USB2_TX_VDD12_SHIFT_MMP3 8 +#define USB2_TX_VDD12_MASK_MMP3 (0x3 << 8) + +/* USB2_TX_REG2 */ +#define USB2_TX_DRV_SLEWRATE_SHIFT 10 + +/* USB2_RX_REG0 */ +#define USB2_RX_SQ_THRESH_SHIFT_MMP3 4 +#define USB2_RX_SQ_THRESH_MASK_MMP3 (0xf << 4) + +#define USB2_RX_SQ_LENGTH_SHIFT_MMP3 10 +#define USB2_RX_SQ_LENGTH_MASK_MMP3 (0x3 << 10) + +/* USB2_ANA_REG1*/ +#define USB2_ANA_PU_ANA_SHIFT_MMP3 14 + +/* USB2_OTG_REG0 */ +#define USB2_OTG_PU_OTG_SHIFT_MMP3 3 + +struct mmp3_usb_phy { + struct phy *phy; + void __iomem *base; +}; + +static unsigned int u2o_get(void __iomem *base, unsigned int offset) +{ + return readl_relaxed(base + offset); +} + +static void u2o_set(void __iomem *base, unsigned int offset, + unsigned int value) +{ + u32 reg; + + reg = readl_relaxed(base + offset); + reg |= value; + writel_relaxed(reg, base + offset); + readl_relaxed(base + offset); +} + +static void u2o_clear(void __iomem *base, unsigned int offset, + unsigned int value) +{ + u32 reg; + + reg = readl_relaxed(base + offset); + reg &= ~value; + writel_relaxed(reg, base + offset); + readl_relaxed(base + offset); +} + +static int mmp3_usb_phy_init(struct phy *phy) +{ + struct mmp3_usb_phy *mmp3_usb_phy = phy_get_drvdata(phy); + void __iomem *base = mmp3_usb_phy->base; + + if (cpu_is_mmp3_a0()) { + u2o_clear(base, USB2_PLL_REG0, (USB2_PLL_FBDIV_MASK_MMP3 + | USB2_PLL_REFDIV_MASK_MMP3)); + u2o_set(base, USB2_PLL_REG0, + 0xd << USB2_PLL_REFDIV_SHIFT_MMP3 + | 0xf0 << USB2_PLL_FBDIV_SHIFT_MMP3); + } else if (cpu_is_mmp3_b0()) { + u2o_clear(base, USB2_PLL_REG0, USB2_PLL_REFDIV_MASK_MMP3_B0 + | USB2_PLL_FBDIV_MASK_MMP3_B0); + u2o_set(base, USB2_PLL_REG0, + 0xd << USB2_PLL_REFDIV_SHIFT_MMP3_B0 + | 0xf0 << USB2_PLL_FBDIV_SHIFT_MMP3_B0); + } else { + dev_err(&phy->dev, "unsupported silicon revision\n"); + return -ENODEV; + } + + u2o_clear(base, USB2_PLL_REG1, USB2_PLL_PU_PLL_MASK + | USB2_PLL_ICP_MASK_MMP3 + | USB2_PLL_KVCO_MASK_MMP3 + | USB2_PLL_CALI12_MASK_MMP3); + u2o_set(base, USB2_PLL_REG1, 1 << USB2_PLL_PU_PLL_SHIFT_MMP3 + | 1 << USB2_PLL_LOCK_BYPASS_SHIFT_MMP3 + | 3 << USB2_PLL_ICP_SHIFT_MMP3 + | 3 << USB2_PLL_KVCO_SHIFT_MMP3 + | 3 << USB2_PLL_CAL12_SHIFT_MMP3); + + u2o_clear(base, USB2_TX_REG0, USB2_TX_IMPCAL_VTH_MASK_MMP3); + u2o_set(base, USB2_TX_REG0, 2 << USB2_TX_IMPCAL_VTH_SHIFT_MMP3); + + u2o_clear(base, USB2_TX_REG1, USB2_TX_VDD12_MASK_MMP3 + | USB2_TX_AMP_MASK_MMP3 + | USB2_TX_CK60_PHSEL_MASK_MMP3); + u2o_set(base, USB2_TX_REG1, 3 << USB2_TX_VDD12_SHIFT_MMP3 + | 4 << USB2_TX_AMP_SHIFT_MMP3 + | 4 << USB2_TX_CK60_PHSEL_SHIFT_MMP3); + + u2o_clear(base, USB2_TX_REG2, 3 << USB2_TX_DRV_SLEWRATE_SHIFT); + u2o_set(base, USB2_TX_REG2, 2 << USB2_TX_DRV_SLEWRATE_SHIFT); + + u2o_clear(base, USB2_RX_REG0, USB2_RX_SQ_THRESH_MASK_MMP3); + u2o_set(base, USB2_RX_REG0, 0xa << USB2_RX_SQ_THRESH_SHIFT_MMP3); + + u2o_set(base, USB2_ANA_REG1, 0x1 << USB2_ANA_PU_ANA_SHIFT_MMP3); + + u2o_set(base, USB2_OTG_REG0, 0x1 << USB2_OTG_PU_OTG_SHIFT_MMP3); + + return 0; +} + +static int mmp3_usb_phy_calibrate(struct phy *phy) +{ + struct mmp3_usb_phy *mmp3_usb_phy = phy_get_drvdata(phy); + void __iomem *base = mmp3_usb_phy->base; + int loops; + + /* + * PLL VCO and TX Impedance Calibration Timing: + * + * _____________________________________ + * PU __________| + * _____________________________ + * VCOCAL START _________| + * ___ + * REG_RCAL_START ________________| |________|_______ + * | 200us | 400us | 40| 400us | USB PHY READY + */ + + udelay(200); + u2o_set(base, USB2_PLL_REG1, 1 << USB2_PLL_VCOCAL_START_SHIFT_MMP3); + udelay(400); + u2o_set(base, USB2_TX_REG0, 1 << USB2_TX_RCAL_START_SHIFT_MMP3); + udelay(40); + u2o_clear(base, USB2_TX_REG0, 1 << USB2_TX_RCAL_START_SHIFT_MMP3); + udelay(400); + + loops = 0; + while ((u2o_get(base, USB2_PLL_REG1) & USB2_PLL_READY_MASK_MMP3) == 0) { + mdelay(1); + loops++; + if (loops > 100) { + dev_err(&phy->dev, "PLL_READY not set after 100mS.\n"); + return -ETIMEDOUT; + } + } + + return 0; +} + +static const struct phy_ops mmp3_usb_phy_ops = { + .init = mmp3_usb_phy_init, + .calibrate = mmp3_usb_phy_calibrate, + .owner = THIS_MODULE, +}; + +static const struct of_device_id mmp3_usb_phy_of_match[] = { + { .compatible = "marvell,mmp3-usb-phy", }, + { }, +}; +MODULE_DEVICE_TABLE(of, mmp3_usb_phy_of_match); + +static int mmp3_usb_phy_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct resource *resource; + struct mmp3_usb_phy *mmp3_usb_phy; + struct phy_provider *provider; + + mmp3_usb_phy = devm_kzalloc(dev, sizeof(*mmp3_usb_phy), GFP_KERNEL); + if (!mmp3_usb_phy) + return -ENOMEM; + + resource = platform_get_resource(pdev, IORESOURCE_MEM, 0); + mmp3_usb_phy->base = devm_ioremap_resource(dev, resource); + if (IS_ERR(mmp3_usb_phy->base)) { + dev_err(dev, "failed to remap PHY regs\n"); + return PTR_ERR(mmp3_usb_phy->base); + } + + mmp3_usb_phy->phy = devm_phy_create(dev, NULL, &mmp3_usb_phy_ops); + if (IS_ERR(mmp3_usb_phy->phy)) { + dev_err(dev, "failed to create PHY\n"); + return PTR_ERR(mmp3_usb_phy->phy); + } + + phy_set_drvdata(mmp3_usb_phy->phy, mmp3_usb_phy); + provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); + if (IS_ERR(provider)) { + dev_err(dev, "failed to register PHY provider\n"); + return PTR_ERR(provider); + } + + return 0; +} + +static struct platform_driver mmp3_usb_phy_driver = { + .probe = mmp3_usb_phy_probe, + .driver = { + .name = "mmp3-usb-phy", + .of_match_table = mmp3_usb_phy_of_match, + }, +}; +module_platform_driver(mmp3_usb_phy_driver); + +MODULE_AUTHOR("Lubomir Rintel <lkundrak@v3.sk>"); +MODULE_DESCRIPTION("Marvell MMP3 USB PHY Driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/phy/marvell/phy-mvebu-a3700-utmi.c b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c index ded900b06f5a..23bc3bf5c4c0 100644 --- a/drivers/phy/marvell/phy-mvebu-a3700-utmi.c +++ b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c @@ -216,20 +216,13 @@ static int mvebu_a3700_utmi_phy_probe(struct platform_device *pdev) struct device *dev = &pdev->dev; struct mvebu_a3700_utmi *utmi; struct phy_provider *provider; - struct resource *res; utmi = devm_kzalloc(dev, sizeof(*utmi), GFP_KERNEL); if (!utmi) return -ENOMEM; /* Get UTMI memory region */ - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!res) { - dev_err(dev, "Missing UTMI PHY memory resource\n"); - return -ENODEV; - } - - utmi->regs = devm_ioremap_resource(dev, res); + utmi->regs = devm_platform_ioremap_resource(pdev, 0); if (IS_ERR(utmi->regs)) return PTR_ERR(utmi->regs); diff --git a/drivers/phy/phy-xgene.c b/drivers/phy/phy-xgene.c index 3c9189473407..7a33ec12f71b 100644 --- a/drivers/phy/phy-xgene.c +++ b/drivers/phy/phy-xgene.c @@ -1342,7 +1342,7 @@ static int xgene_phy_hw_initialize(struct xgene_phy_ctx *ctx, static void xgene_phy_force_lat_summer_cal(struct xgene_phy_ctx *ctx, int lane) { int i; - struct { + static const struct { u32 reg; u32 val; } serdes_reg[] = { diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c index 39e8deb8001e..091e20303a14 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp.c +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c @@ -165,6 +165,11 @@ static const unsigned int sdm845_ufsphy_regs_layout[] = { [QPHY_PCS_READY_STATUS] = 0x160, }; +static const unsigned int sm8150_ufsphy_regs_layout[] = { + [QPHY_START_CTRL] = 0x00, + [QPHY_PCS_READY_STATUS] = 0x180, +}; + static const struct qmp_phy_init_tbl msm8996_pcie_serdes_tbl[] = { QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x1c), QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10), @@ -879,6 +884,93 @@ static const struct qmp_phy_init_tbl msm8998_usb3_pcs_tbl[] = { QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13), }; +static const struct qmp_phy_init_tbl sm8150_ufsphy_serdes_tbl[] = { + QMP_PHY_INIT_CFG(QPHY_POWER_DOWN_CONTROL, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_EN_SEL, 0xd9), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_HSCLK_SEL, 0x11), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_HSCLK_HS_SWITCH_SEL, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP_EN, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE_MAP, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_IVCO, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE_INITVAL2, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_HSCLK_SEL, 0x11), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_DEC_START_MODE0, 0x82), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_CP_CTRL_MODE0, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_RCTRL_MODE0, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_CCTRL_MODE0, 0x36), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP1_MODE0, 0xff), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP2_MODE0, 0x0c), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE0, 0xac), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE0, 0x1e), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_DEC_START_MODE1, 0x98), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_CP_CTRL_MODE1, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_RCTRL_MODE1, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_CCTRL_MODE1, 0x36), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP1_MODE1, 0x32), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP2_MODE1, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE1, 0xdd), + QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE1, 0x23), + + /* Rate B */ + QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE_MAP, 0x06), +}; + +static const struct qmp_phy_init_tbl sm8150_ufsphy_tx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_1_DIVIDER_BAND0_1, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_2_DIVIDER_BAND0_1, 0x03), + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_3_DIVIDER_BAND0_1, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_4_DIVIDER_BAND0_1, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0x05), + QMP_PHY_INIT_CFG(QSERDES_V4_TX_TRAN_DRVR_EMP_EN, 0x0c), +}; + +static const struct qmp_phy_init_tbl sm8150_ufsphy_rx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_LVL, 0x24), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x1e), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_BAND, 0x18), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x4b), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0xf1), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0x80), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CTRL2, 0x80), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x0c), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_TERM_BW, 0x1b), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x1d), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_MEASURE_TIME, 0x10), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0x36), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x36), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0xf6), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x3b), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x3d), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xe0), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x3b), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb1), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_LOW, 0xe0), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH2, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH3, 0x3b), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH4, 0xb1), + +}; + +static const struct qmp_phy_init_tbl sm8150_ufsphy_pcs_tbl[] = { + QMP_PHY_INIT_CFG(QPHY_V4_RX_SIGDET_CTRL2, 0x6d), + QMP_PHY_INIT_CFG(QPHY_V4_TX_LARGE_AMP_DRV_LVL, 0x0a), + QMP_PHY_INIT_CFG(QPHY_V4_TX_SMALL_AMP_DRV_LVL, 0x02), + QMP_PHY_INIT_CFG(QPHY_V4_TX_MID_TERM_CTRL1, 0x43), + QMP_PHY_INIT_CFG(QPHY_V4_DEBUG_BUS_CLKSEL, 0x1f), + QMP_PHY_INIT_CFG(QPHY_V4_RX_MIN_HIBERN8_TIME, 0xff), + QMP_PHY_INIT_CFG(QPHY_V4_MULTI_LANE_CTRL1, 0x02), +}; /* struct qmp_phy_cfg - per-PHY initialization config */ struct qmp_phy_cfg { @@ -1276,6 +1368,31 @@ static const struct qmp_phy_cfg msm8998_usb3phy_cfg = { .is_dual_lane_phy = true, }; +static const struct qmp_phy_cfg sm8150_ufsphy_cfg = { + .type = PHY_TYPE_UFS, + .nlanes = 2, + + .serdes_tbl = sm8150_ufsphy_serdes_tbl, + .serdes_tbl_num = ARRAY_SIZE(sm8150_ufsphy_serdes_tbl), + .tx_tbl = sm8150_ufsphy_tx_tbl, + .tx_tbl_num = ARRAY_SIZE(sm8150_ufsphy_tx_tbl), + .rx_tbl = sm8150_ufsphy_rx_tbl, + .rx_tbl_num = ARRAY_SIZE(sm8150_ufsphy_rx_tbl), + .pcs_tbl = sm8150_ufsphy_pcs_tbl, + .pcs_tbl_num = ARRAY_SIZE(sm8150_ufsphy_pcs_tbl), + .clk_list = sdm845_ufs_phy_clk_l, + .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l), + .vreg_list = qmp_phy_vreg_l, + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), + .regs = sm8150_ufsphy_regs_layout, + + .start_ctrl = SERDES_START, + .pwrdn_ctrl = SW_PWRDN, + + .is_dual_lane_phy = true, + .no_pcs_sw_reset = true, +}; + static void qcom_qmp_phy_configure(void __iomem *base, const unsigned int *regs, const struct qmp_phy_init_tbl tbl[], @@ -1998,6 +2115,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = { }, { .compatible = "qcom,msm8998-qmp-usb3-phy", .data = &msm8998_usb3phy_cfg, + }, { + .compatible = "qcom,sm8150-qmp-ufs-phy", + .data = &sm8150_ufsphy_cfg, }, { }, }; diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h index 335ea5d7ef40..ab6ff9b45a32 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp.h +++ b/drivers/phy/qualcomm/phy-qcom-qmp.h @@ -313,4 +313,100 @@ #define QPHY_V3_PCS_MISC_OSC_DTCT_MODE2_CONFIG4 0x5c #define QPHY_V3_PCS_MISC_OSC_DTCT_MODE2_CONFIG5 0x60 +/* Only for QMP V4 PHY - QSERDES COM registers */ +#define QSERDES_V4_COM_PLL_IVCO 0x058 +#define QSERDES_V4_COM_CMN_IPTRIM 0x060 +#define QSERDES_V4_COM_CP_CTRL_MODE0 0x074 +#define QSERDES_V4_COM_CP_CTRL_MODE1 0x078 +#define QSERDES_V4_COM_PLL_RCTRL_MODE0 0x07c +#define QSERDES_V4_COM_PLL_RCTRL_MODE1 0x080 +#define QSERDES_V4_COM_PLL_CCTRL_MODE0 0x084 +#define QSERDES_V4_COM_PLL_CCTRL_MODE1 0x088 +#define QSERDES_V4_COM_SYSCLK_EN_SEL 0x094 +#define QSERDES_V4_COM_LOCK_CMP_EN 0x0a4 +#define QSERDES_V4_COM_LOCK_CMP1_MODE0 0x0ac +#define QSERDES_V4_COM_LOCK_CMP2_MODE0 0x0b0 +#define QSERDES_V4_COM_LOCK_CMP1_MODE1 0x0b4 +#define QSERDES_V4_COM_DEC_START_MODE0 0x0bc +#define QSERDES_V4_COM_LOCK_CMP2_MODE1 0x0b8 +#define QSERDES_V4_COM_DEC_START_MODE1 0x0c4 +#define QSERDES_V4_COM_VCO_TUNE_MAP 0x10c +#define QSERDES_V4_COM_VCO_TUNE_INITVAL2 0x124 +#define QSERDES_V4_COM_HSCLK_SEL 0x158 +#define QSERDES_V4_COM_HSCLK_HS_SWITCH_SEL 0x15c +#define QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE0 0x1ac +#define QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE0 0x1b0 +#define QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE1 0x1b4 +#define QSERDES_V4_COM_BIN_VCOCAL_HSCLK_SEL 0x1bc +#define QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE1 0x1b8 + +/* Only for QMP V4 PHY - TX registers */ +#define QSERDES_V4_TX_LANE_MODE_1 0x84 +#define QSERDES_V4_TX_PWM_GEAR_1_DIVIDER_BAND0_1 0xd8 +#define QSERDES_V4_TX_PWM_GEAR_2_DIVIDER_BAND0_1 0xdC +#define QSERDES_V4_TX_PWM_GEAR_3_DIVIDER_BAND0_1 0xe0 +#define QSERDES_V4_TX_PWM_GEAR_4_DIVIDER_BAND0_1 0xe4 +#define QSERDES_V4_TX_TRAN_DRVR_EMP_EN 0xb8 + +/* Only for QMP V4 PHY - RX registers */ +#define QSERDES_V4_RX_UCDR_FO_GAIN 0x008 +#define QSERDES_V4_RX_UCDR_SO_GAIN 0x014 +#define QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN 0x030 +#define QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE 0x034 +#define QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW 0x03c +#define QSERDES_V4_RX_UCDR_PI_CONTROLS 0x044 +#define QSERDES_V4_RX_UCDR_PI_CTRL2 0x048 +#define QSERDES_V4_RX_AC_JTAG_ENABLE 0x068 +#define QSERDES_V4_RX_AC_JTAG_MODE 0x078 +#define QSERDES_V4_RX_RX_TERM_BW 0x080 +#define QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2 0x0ec +#define QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3 0x0f0 +#define QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4 0x0f4 +#define QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW 0x0f8 +#define QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH 0x0fc +#define QSERDES_V4_RX_RX_IDAC_MEASURE_TIME 0x100 +#define QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2 0x114 +#define QSERDES_V4_RX_SIGDET_CNTRL 0x11c +#define QSERDES_V4_RX_SIGDET_LVL 0x120 +#define QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL 0x124 +#define QSERDES_V4_RX_RX_BAND 0x128 +#define QSERDES_V4_RX_RX_MODE_00_LOW 0x170 +#define QSERDES_V4_RX_RX_MODE_00_HIGH 0x174 +#define QSERDES_V4_RX_RX_MODE_00_HIGH2 0x178 +#define QSERDES_V4_RX_RX_MODE_00_HIGH3 0x17c +#define QSERDES_V4_RX_RX_MODE_00_HIGH4 0x180 +#define QSERDES_V4_RX_RX_MODE_01_LOW 0x184 +#define QSERDES_V4_RX_RX_MODE_01_HIGH 0x188 +#define QSERDES_V4_RX_RX_MODE_01_HIGH2 0x18c +#define QSERDES_V4_RX_RX_MODE_01_HIGH3 0x190 +#define QSERDES_V4_RX_RX_MODE_01_HIGH4 0x194 +#define QSERDES_V4_RX_RX_MODE_10_LOW 0x198 +#define QSERDES_V4_RX_RX_MODE_10_HIGH 0x19c +#define QSERDES_V4_RX_RX_MODE_10_HIGH2 0x1a0 +#define QSERDES_V4_RX_RX_MODE_10_HIGH3 0x1a4 +#define QSERDES_V4_RX_RX_MODE_10_HIGH4 0x1a8 +#define QSERDES_V4_RX_DCC_CTRL1 0x1bc + +/* Only for QMP V4 PHY - PCS registers */ +#define QPHY_V4_PHY_START 0x000 +#define QPHY_V4_POWER_DOWN_CONTROL 0x004 +#define QPHY_V4_SW_RESET 0x008 +#define QPHY_V4_TIMER_20US_CORECLK_STEPS_MSB 0x00c +#define QPHY_V4_TIMER_20US_CORECLK_STEPS_LSB 0x010 +#define QPHY_V4_PLL_CNTL 0x02c +#define QPHY_V4_TX_LARGE_AMP_DRV_LVL 0x030 +#define QPHY_V4_TX_SMALL_AMP_DRV_LVL 0x038 +#define QPHY_V4_BIST_FIXED_PAT_CTRL 0x060 +#define QPHY_V4_TX_HSGEAR_CAPABILITY 0x074 +#define QPHY_V4_RX_HSGEAR_CAPABILITY 0x0b4 +#define QPHY_V4_DEBUG_BUS_CLKSEL 0x124 +#define QPHY_V4_LINECFG_DISABLE 0x148 +#define QPHY_V4_RX_MIN_HIBERN8_TIME 0x150 +#define QPHY_V4_RX_SIGDET_CTRL2 0x158 +#define QPHY_V4_TX_PWM_GEAR_BAND 0x160 +#define QPHY_V4_TX_HS_GEAR_BAND 0x168 +#define QPHY_V4_PCS_READY_STATUS 0x180 +#define QPHY_V4_TX_MID_TERM_CTRL1 0x1d8 +#define QPHY_V4_MULTI_LANE_CTRL1 0x1e0 + #endif diff --git a/drivers/phy/qualcomm/phy-qcom-usb-hs.c b/drivers/phy/qualcomm/phy-qcom-usb-hs.c index b163b3a1558d..61054272a7c8 100644 --- a/drivers/phy/qualcomm/phy-qcom-usb-hs.c +++ b/drivers/phy/qualcomm/phy-qcom-usb-hs.c @@ -158,8 +158,8 @@ static int qcom_usb_hs_phy_power_on(struct phy *phy) /* setup initial state */ qcom_usb_hs_phy_vbus_notifier(&uphy->vbus_notify, state, uphy->vbus_edev); - ret = devm_extcon_register_notifier(&ulpi->dev, uphy->vbus_edev, - EXTCON_USB, &uphy->vbus_notify); + ret = extcon_register_notifier(uphy->vbus_edev, EXTCON_USB, + &uphy->vbus_notify); if (ret) goto err_ulpi; } @@ -180,6 +180,9 @@ static int qcom_usb_hs_phy_power_off(struct phy *phy) { struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy); + if (uphy->vbus_edev) + extcon_unregister_notifier(uphy->vbus_edev, EXTCON_USB, + &uphy->vbus_notify); regulator_disable(uphy->v3p3); regulator_disable(uphy->v1p8); clk_disable_unprepare(uphy->sleep_clk); diff --git a/drivers/phy/renesas/phy-rcar-gen2.c b/drivers/phy/renesas/phy-rcar-gen2.c index 2926e4937301..2e279ac0fa4d 100644 --- a/drivers/phy/renesas/phy-rcar-gen2.c +++ b/drivers/phy/renesas/phy-rcar-gen2.c @@ -71,6 +71,7 @@ struct rcar_gen2_phy_driver { struct rcar_gen2_phy_data { const struct phy_ops *gen2_phy_ops; const u32 (*select_value)[PHYS_PER_CHANNEL]; + const u32 num_channels; }; static int rcar_gen2_phy_init(struct phy *p) @@ -271,11 +272,13 @@ static const u32 usb20_select_value[][PHYS_PER_CHANNEL] = { static const struct rcar_gen2_phy_data rcar_gen2_usb_phy_data = { .gen2_phy_ops = &rcar_gen2_phy_ops, .select_value = pci_select_value, + .num_channels = ARRAY_SIZE(pci_select_value), }; static const struct rcar_gen2_phy_data rz_g1c_usb_phy_data = { .gen2_phy_ops = &rz_g1c_phy_ops, .select_value = usb20_select_value, + .num_channels = ARRAY_SIZE(usb20_select_value), }; static const struct of_device_id rcar_gen2_phy_match_table[] = { @@ -389,7 +392,7 @@ static int rcar_gen2_phy_probe(struct platform_device *pdev) channel->selected_phy = -1; error = of_property_read_u32(np, "reg", &channel_num); - if (error || channel_num > 2) { + if (error || channel_num >= data->num_channels) { dev_err(dev, "Invalid \"reg\" property\n"); of_node_put(np); return error; diff --git a/drivers/phy/renesas/phy-rcar-gen3-usb2.c b/drivers/phy/renesas/phy-rcar-gen3-usb2.c index b7f6b1324395..bfb22f868857 100644 --- a/drivers/phy/renesas/phy-rcar-gen3-usb2.c +++ b/drivers/phy/renesas/phy-rcar-gen3-usb2.c @@ -21,6 +21,7 @@ #include <linux/platform_device.h> #include <linux/pm_runtime.h> #include <linux/regulator/consumer.h> +#include <linux/string.h> #include <linux/usb/of.h> #include <linux/workqueue.h> @@ -320,9 +321,9 @@ static ssize_t role_store(struct device *dev, struct device_attribute *attr, if (!ch->is_otg_channel || !rcar_gen3_is_any_rphy_initialized(ch)) return -EIO; - if (!strncmp(buf, "host", strlen("host"))) + if (sysfs_streq(buf, "host")) new_mode = PHY_MODE_USB_HOST; - else if (!strncmp(buf, "peripheral", strlen("peripheral"))) + else if (sysfs_streq(buf, "peripheral")) new_mode = PHY_MODE_USB_DEVICE; else return -EINVAL; @@ -614,7 +615,7 @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) return PTR_ERR(channel->base); /* call request_irq for OTG */ - irq = platform_get_irq(pdev, 0); + irq = platform_get_irq_optional(pdev, 0); if (irq >= 0) { INIT_WORK(&channel->work, rcar_gen3_phy_usb2_work); irq = devm_request_irq(dev, irq, rcar_gen3_phy_usb2_irq, diff --git a/drivers/phy/rockchip/Kconfig b/drivers/phy/rockchip/Kconfig index c454c90cd99e..dbd2de4d28b1 100644 --- a/drivers/phy/rockchip/Kconfig +++ b/drivers/phy/rockchip/Kconfig @@ -35,6 +35,14 @@ config PHY_ROCKCHIP_INNO_USB2 help Support for Rockchip USB2.0 PHY with Innosilicon IP block. +config PHY_ROCKCHIP_INNO_DSIDPHY + tristate "Rockchip Innosilicon MIPI/LVDS/TTL PHY driver" + depends on (ARCH_ROCKCHIP || COMPILE_TEST) && OF + select GENERIC_PHY + help + Enable this to support the Rockchip MIPI/LVDS/TTL PHY with + Innosilicon IP block. + config PHY_ROCKCHIP_PCIE tristate "Rockchip PCIe PHY Driver" depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST diff --git a/drivers/phy/rockchip/Makefile b/drivers/phy/rockchip/Makefile index fd21cbaf40dd..9f59a81e4e0d 100644 --- a/drivers/phy/rockchip/Makefile +++ b/drivers/phy/rockchip/Makefile @@ -1,6 +1,7 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_PHY_ROCKCHIP_DP) += phy-rockchip-dp.o obj-$(CONFIG_PHY_ROCKCHIP_EMMC) += phy-rockchip-emmc.o +obj-$(CONFIG_PHY_ROCKCHIP_INNO_DSIDPHY) += phy-rockchip-inno-dsidphy.o obj-$(CONFIG_PHY_ROCKCHIP_INNO_HDMI) += phy-rockchip-inno-hdmi.o obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2) += phy-rockchip-inno-usb2.o obj-$(CONFIG_PHY_ROCKCHIP_PCIE) += phy-rockchip-pcie.o diff --git a/drivers/phy/rockchip/phy-rockchip-inno-dsidphy.c b/drivers/phy/rockchip/phy-rockchip-inno-dsidphy.c new file mode 100644 index 000000000000..fc729ecd3fe9 --- /dev/null +++ b/drivers/phy/rockchip/phy-rockchip-inno-dsidphy.c @@ -0,0 +1,805 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2018 Rockchip Electronics Co. Ltd. + * + * Author: Wyon Bi <bivvy.bi@rock-chips.com> + */ + +#include <linux/kernel.h> +#include <linux/clk.h> +#include <linux/iopoll.h> +#include <linux/clk-provider.h> +#include <linux/delay.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/reset.h> +#include <linux/phy/phy.h> +#include <linux/pm_runtime.h> +#include <linux/mfd/syscon.h> + +#define PSEC_PER_SEC 1000000000000LL + +#define UPDATE(x, h, l) (((x) << (l)) & GENMASK((h), (l))) + +/* + * The offset address[7:0] is distributed two parts, one from the bit7 to bit5 + * is the first address, the other from the bit4 to bit0 is the second address. + * when you configure the registers, you must set both of them. The Clock Lane + * and Data Lane use the same registers with the same second address, but the + * first address is different. + */ +#define FIRST_ADDRESS(x) (((x) & 0x7) << 5) +#define SECOND_ADDRESS(x) (((x) & 0x1f) << 0) +#define PHY_REG(first, second) (FIRST_ADDRESS(first) | \ + SECOND_ADDRESS(second)) + +/* Analog Register Part: reg00 */ +#define BANDGAP_POWER_MASK BIT(7) +#define BANDGAP_POWER_DOWN BIT(7) +#define BANDGAP_POWER_ON 0 +#define LANE_EN_MASK GENMASK(6, 2) +#define LANE_EN_CK BIT(6) +#define LANE_EN_3 BIT(5) +#define LANE_EN_2 BIT(4) +#define LANE_EN_1 BIT(3) +#define LANE_EN_0 BIT(2) +#define POWER_WORK_MASK GENMASK(1, 0) +#define POWER_WORK_ENABLE UPDATE(1, 1, 0) +#define POWER_WORK_DISABLE UPDATE(2, 1, 0) +/* Analog Register Part: reg01 */ +#define REG_SYNCRST_MASK BIT(2) +#define REG_SYNCRST_RESET BIT(2) +#define REG_SYNCRST_NORMAL 0 +#define REG_LDOPD_MASK BIT(1) +#define REG_LDOPD_POWER_DOWN BIT(1) +#define REG_LDOPD_POWER_ON 0 +#define REG_PLLPD_MASK BIT(0) +#define REG_PLLPD_POWER_DOWN BIT(0) +#define REG_PLLPD_POWER_ON 0 +/* Analog Register Part: reg03 */ +#define REG_FBDIV_HI_MASK BIT(5) +#define REG_FBDIV_HI(x) UPDATE((x >> 8), 5, 5) +#define REG_PREDIV_MASK GENMASK(4, 0) +#define REG_PREDIV(x) UPDATE(x, 4, 0) +/* Analog Register Part: reg04 */ +#define REG_FBDIV_LO_MASK GENMASK(7, 0) +#define REG_FBDIV_LO(x) UPDATE(x, 7, 0) +/* Analog Register Part: reg05 */ +#define SAMPLE_CLOCK_PHASE_MASK GENMASK(6, 4) +#define SAMPLE_CLOCK_PHASE(x) UPDATE(x, 6, 4) +#define CLOCK_LANE_SKEW_PHASE_MASK GENMASK(2, 0) +#define CLOCK_LANE_SKEW_PHASE(x) UPDATE(x, 2, 0) +/* Analog Register Part: reg06 */ +#define DATA_LANE_3_SKEW_PHASE_MASK GENMASK(6, 4) +#define DATA_LANE_3_SKEW_PHASE(x) UPDATE(x, 6, 4) +#define DATA_LANE_2_SKEW_PHASE_MASK GENMASK(2, 0) +#define DATA_LANE_2_SKEW_PHASE(x) UPDATE(x, 2, 0) +/* Analog Register Part: reg07 */ +#define DATA_LANE_1_SKEW_PHASE_MASK GENMASK(6, 4) +#define DATA_LANE_1_SKEW_PHASE(x) UPDATE(x, 6, 4) +#define DATA_LANE_0_SKEW_PHASE_MASK GENMASK(2, 0) +#define DATA_LANE_0_SKEW_PHASE(x) UPDATE(x, 2, 0) +/* Analog Register Part: reg08 */ +#define SAMPLE_CLOCK_DIRECTION_MASK BIT(4) +#define SAMPLE_CLOCK_DIRECTION_REVERSE BIT(4) +#define SAMPLE_CLOCK_DIRECTION_FORWARD 0 +/* Digital Register Part: reg00 */ +#define REG_DIG_RSTN_MASK BIT(0) +#define REG_DIG_RSTN_NORMAL BIT(0) +#define REG_DIG_RSTN_RESET 0 +/* Digital Register Part: reg01 */ +#define INVERT_TXCLKESC_MASK BIT(1) +#define INVERT_TXCLKESC_ENABLE BIT(1) +#define INVERT_TXCLKESC_DISABLE 0 +#define INVERT_TXBYTECLKHS_MASK BIT(0) +#define INVERT_TXBYTECLKHS_ENABLE BIT(0) +#define INVERT_TXBYTECLKHS_DISABLE 0 +/* Clock/Data0/Data1/Data2/Data3 Lane Register Part: reg05 */ +#define T_LPX_CNT_MASK GENMASK(5, 0) +#define T_LPX_CNT(x) UPDATE(x, 5, 0) +/* Clock/Data0/Data1/Data2/Data3 Lane Register Part: reg06 */ +#define T_HS_PREPARE_CNT_MASK GENMASK(6, 0) +#define T_HS_PREPARE_CNT(x) UPDATE(x, 6, 0) +/* Clock/Data0/Data1/Data2/Data3 Lane Register Part: reg07 */ +#define T_HS_ZERO_CNT_MASK GENMASK(5, 0) +#define T_HS_ZERO_CNT(x) UPDATE(x, 5, 0) +/* Clock/Data0/Data1/Data2/Data3 Lane Register Part: reg08 */ +#define T_HS_TRAIL_CNT_MASK GENMASK(6, 0) +#define T_HS_TRAIL_CNT(x) UPDATE(x, 6, 0) +/* Clock/Data0/Data1/Data2/Data3 Lane Register Part: reg09 */ +#define T_HS_EXIT_CNT_MASK GENMASK(4, 0) +#define T_HS_EXIT_CNT(x) UPDATE(x, 4, 0) +/* Clock/Data0/Data1/Data2/Data3 Lane Register Part: reg0a */ +#define T_CLK_POST_CNT_MASK GENMASK(3, 0) +#define T_CLK_POST_CNT(x) UPDATE(x, 3, 0) +/* Clock/Data0/Data1/Data2/Data3 Lane Register Part: reg0c */ +#define LPDT_TX_PPI_SYNC_MASK BIT(2) +#define LPDT_TX_PPI_SYNC_ENABLE BIT(2) +#define LPDT_TX_PPI_SYNC_DISABLE 0 +#define T_WAKEUP_CNT_HI_MASK GENMASK(1, 0) +#define T_WAKEUP_CNT_HI(x) UPDATE(x, 1, 0) +/* Clock/Data0/Data1/Data2/Data3 Lane Register Part: reg0d */ +#define T_WAKEUP_CNT_LO_MASK GENMASK(7, 0) +#define T_WAKEUP_CNT_LO(x) UPDATE(x, 7, 0) +/* Clock/Data0/Data1/Data2/Data3 Lane Register Part: reg0e */ +#define T_CLK_PRE_CNT_MASK GENMASK(3, 0) +#define T_CLK_PRE_CNT(x) UPDATE(x, 3, 0) +/* Clock/Data0/Data1/Data2/Data3 Lane Register Part: reg10 */ +#define T_TA_GO_CNT_MASK GENMASK(5, 0) +#define T_TA_GO_CNT(x) UPDATE(x, 5, 0) +/* Clock/Data0/Data1/Data2/Data3 Lane Register Part: reg11 */ +#define T_TA_SURE_CNT_MASK GENMASK(5, 0) +#define T_TA_SURE_CNT(x) UPDATE(x, 5, 0) +/* Clock/Data0/Data1/Data2/Data3 Lane Register Part: reg12 */ +#define T_TA_WAIT_CNT_MASK GENMASK(5, 0) +#define T_TA_WAIT_CNT(x) UPDATE(x, 5, 0) +/* LVDS Register Part: reg00 */ +#define LVDS_DIGITAL_INTERNAL_RESET_MASK BIT(2) +#define LVDS_DIGITAL_INTERNAL_RESET_DISABLE BIT(2) +#define LVDS_DIGITAL_INTERNAL_RESET_ENABLE 0 +/* LVDS Register Part: reg01 */ +#define LVDS_DIGITAL_INTERNAL_ENABLE_MASK BIT(7) +#define LVDS_DIGITAL_INTERNAL_ENABLE BIT(7) +#define LVDS_DIGITAL_INTERNAL_DISABLE 0 +/* LVDS Register Part: reg03 */ +#define MODE_ENABLE_MASK GENMASK(2, 0) +#define TTL_MODE_ENABLE BIT(2) +#define LVDS_MODE_ENABLE BIT(1) +#define MIPI_MODE_ENABLE BIT(0) +/* LVDS Register Part: reg0b */ +#define LVDS_LANE_EN_MASK GENMASK(7, 3) +#define LVDS_DATA_LANE0_EN BIT(7) +#define LVDS_DATA_LANE1_EN BIT(6) +#define LVDS_DATA_LANE2_EN BIT(5) +#define LVDS_DATA_LANE3_EN BIT(4) +#define LVDS_CLK_LANE_EN BIT(3) +#define LVDS_PLL_POWER_MASK BIT(2) +#define LVDS_PLL_POWER_OFF BIT(2) +#define LVDS_PLL_POWER_ON 0 +#define LVDS_BANDGAP_POWER_MASK BIT(0) +#define LVDS_BANDGAP_POWER_DOWN BIT(0) +#define LVDS_BANDGAP_POWER_ON 0 + +#define DSI_PHY_RSTZ 0xa0 +#define PHY_ENABLECLK BIT(2) +#define DSI_PHY_STATUS 0xb0 +#define PHY_LOCK BIT(0) + +struct mipi_dphy_timing { + unsigned int clkmiss; + unsigned int clkpost; + unsigned int clkpre; + unsigned int clkprepare; + unsigned int clksettle; + unsigned int clktermen; + unsigned int clktrail; + unsigned int clkzero; + unsigned int dtermen; + unsigned int eot; + unsigned int hsexit; + unsigned int hsprepare; + unsigned int hszero; + unsigned int hssettle; + unsigned int hsskip; + unsigned int hstrail; + unsigned int init; + unsigned int lpx; + unsigned int taget; + unsigned int tago; + unsigned int tasure; + unsigned int wakeup; +}; + +struct inno_dsidphy { + struct device *dev; + struct clk *ref_clk; + struct clk *pclk_phy; + struct clk *pclk_host; + void __iomem *phy_base; + void __iomem *host_base; + struct reset_control *rst; + enum phy_mode mode; + + struct { + struct clk_hw hw; + u8 prediv; + u16 fbdiv; + unsigned long rate; + } pll; +}; + +enum { + REGISTER_PART_ANALOG, + REGISTER_PART_DIGITAL, + REGISTER_PART_CLOCK_LANE, + REGISTER_PART_DATA0_LANE, + REGISTER_PART_DATA1_LANE, + REGISTER_PART_DATA2_LANE, + REGISTER_PART_DATA3_LANE, + REGISTER_PART_LVDS, +}; + +static inline struct inno_dsidphy *hw_to_inno(struct clk_hw *hw) +{ + return container_of(hw, struct inno_dsidphy, pll.hw); +} + +static void phy_update_bits(struct inno_dsidphy *inno, + u8 first, u8 second, u8 mask, u8 val) +{ + u32 reg = PHY_REG(first, second) << 2; + unsigned int tmp, orig; + + orig = readl(inno->phy_base + reg); + tmp = orig & ~mask; + tmp |= val & mask; + writel(tmp, inno->phy_base + reg); +} + +static void mipi_dphy_timing_get_default(struct mipi_dphy_timing *timing, + unsigned long period) +{ + /* Global Operation Timing Parameters */ + timing->clkmiss = 0; + timing->clkpost = 70000 + 52 * period; + timing->clkpre = 8 * period; + timing->clkprepare = 65000; + timing->clksettle = 95000; + timing->clktermen = 0; + timing->clktrail = 80000; + timing->clkzero = 260000; + timing->dtermen = 0; + timing->eot = 0; + timing->hsexit = 120000; + timing->hsprepare = 65000 + 4 * period; + timing->hszero = 145000 + 6 * period; + timing->hssettle = 85000 + 6 * period; + timing->hsskip = 40000; + timing->hstrail = max(8 * period, 60000 + 4 * period); + timing->init = 100000000; + timing->lpx = 60000; + timing->taget = 5 * timing->lpx; + timing->tago = 4 * timing->lpx; + timing->tasure = 2 * timing->lpx; + timing->wakeup = 1000000000; +} + +static void inno_dsidphy_mipi_mode_enable(struct inno_dsidphy *inno) +{ + struct mipi_dphy_timing gotp; + const struct { + unsigned long rate; + u8 hs_prepare; + u8 clk_lane_hs_zero; + u8 data_lane_hs_zero; + u8 hs_trail; + } timings[] = { + { 110000000, 0x20, 0x16, 0x02, 0x22}, + { 150000000, 0x06, 0x16, 0x03, 0x45}, + { 200000000, 0x18, 0x17, 0x04, 0x0b}, + { 250000000, 0x05, 0x17, 0x05, 0x16}, + { 300000000, 0x51, 0x18, 0x06, 0x2c}, + { 400000000, 0x64, 0x19, 0x07, 0x33}, + { 500000000, 0x20, 0x1b, 0x07, 0x4e}, + { 600000000, 0x6a, 0x1d, 0x08, 0x3a}, + { 700000000, 0x3e, 0x1e, 0x08, 0x6a}, + { 800000000, 0x21, 0x1f, 0x09, 0x29}, + {1000000000, 0x09, 0x20, 0x09, 0x27}, + }; + u32 t_txbyteclkhs, t_txclkesc, ui; + u32 txbyteclkhs, txclkesc, esc_clk_div; + u32 hs_exit, clk_post, clk_pre, wakeup, lpx, ta_go, ta_sure, ta_wait; + u32 hs_prepare, hs_trail, hs_zero, clk_lane_hs_zero, data_lane_hs_zero; + unsigned int i; + + /* Select MIPI mode */ + phy_update_bits(inno, REGISTER_PART_LVDS, 0x03, + MODE_ENABLE_MASK, MIPI_MODE_ENABLE); + /* Configure PLL */ + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x03, + REG_PREDIV_MASK, REG_PREDIV(inno->pll.prediv)); + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x03, + REG_FBDIV_HI_MASK, REG_FBDIV_HI(inno->pll.fbdiv)); + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x04, + REG_FBDIV_LO_MASK, REG_FBDIV_LO(inno->pll.fbdiv)); + /* Enable PLL and LDO */ + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x01, + REG_LDOPD_MASK | REG_PLLPD_MASK, + REG_LDOPD_POWER_ON | REG_PLLPD_POWER_ON); + /* Reset analog */ + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x01, + REG_SYNCRST_MASK, REG_SYNCRST_RESET); + udelay(1); + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x01, + REG_SYNCRST_MASK, REG_SYNCRST_NORMAL); + /* Reset digital */ + phy_update_bits(inno, REGISTER_PART_DIGITAL, 0x00, + REG_DIG_RSTN_MASK, REG_DIG_RSTN_RESET); + udelay(1); + phy_update_bits(inno, REGISTER_PART_DIGITAL, 0x00, + REG_DIG_RSTN_MASK, REG_DIG_RSTN_NORMAL); + + txbyteclkhs = inno->pll.rate / 8; + t_txbyteclkhs = div_u64(PSEC_PER_SEC, txbyteclkhs); + + esc_clk_div = DIV_ROUND_UP(txbyteclkhs, 20000000); + txclkesc = txbyteclkhs / esc_clk_div; + t_txclkesc = div_u64(PSEC_PER_SEC, txclkesc); + + ui = div_u64(PSEC_PER_SEC, inno->pll.rate); + + memset(&gotp, 0, sizeof(gotp)); + mipi_dphy_timing_get_default(&gotp, ui); + + /* + * The value of counter for HS Ths-exit + * Ths-exit = Tpin_txbyteclkhs * value + */ + hs_exit = DIV_ROUND_UP(gotp.hsexit, t_txbyteclkhs); + /* + * The value of counter for HS Tclk-post + * Tclk-post = Tpin_txbyteclkhs * value + */ + clk_post = DIV_ROUND_UP(gotp.clkpost, t_txbyteclkhs); + /* + * The value of counter for HS Tclk-pre + * Tclk-pre = Tpin_txbyteclkhs * value + */ + clk_pre = DIV_ROUND_UP(gotp.clkpre, t_txbyteclkhs); + + /* + * The value of counter for HS Tlpx Time + * Tlpx = Tpin_txbyteclkhs * (2 + value) + */ + lpx = DIV_ROUND_UP(gotp.lpx, t_txbyteclkhs); + if (lpx >= 2) + lpx -= 2; + + /* + * The value of counter for HS Tta-go + * Tta-go for turnaround + * Tta-go = Ttxclkesc * value + */ + ta_go = DIV_ROUND_UP(gotp.tago, t_txclkesc); + /* + * The value of counter for HS Tta-sure + * Tta-sure for turnaround + * Tta-sure = Ttxclkesc * value + */ + ta_sure = DIV_ROUND_UP(gotp.tasure, t_txclkesc); + /* + * The value of counter for HS Tta-wait + * Tta-wait for turnaround + * Tta-wait = Ttxclkesc * value + */ + ta_wait = DIV_ROUND_UP(gotp.taget, t_txclkesc); + + for (i = 0; i < ARRAY_SIZE(timings); i++) + if (inno->pll.rate <= timings[i].rate) + break; + + if (i == ARRAY_SIZE(timings)) + --i; + + hs_prepare = timings[i].hs_prepare; + hs_trail = timings[i].hs_trail; + clk_lane_hs_zero = timings[i].clk_lane_hs_zero; + data_lane_hs_zero = timings[i].data_lane_hs_zero; + wakeup = 0x3ff; + + for (i = REGISTER_PART_CLOCK_LANE; i <= REGISTER_PART_DATA3_LANE; i++) { + if (i == REGISTER_PART_CLOCK_LANE) + hs_zero = clk_lane_hs_zero; + else + hs_zero = data_lane_hs_zero; + + phy_update_bits(inno, i, 0x05, T_LPX_CNT_MASK, + T_LPX_CNT(lpx)); + phy_update_bits(inno, i, 0x06, T_HS_PREPARE_CNT_MASK, + T_HS_PREPARE_CNT(hs_prepare)); + phy_update_bits(inno, i, 0x07, T_HS_ZERO_CNT_MASK, + T_HS_ZERO_CNT(hs_zero)); + phy_update_bits(inno, i, 0x08, T_HS_TRAIL_CNT_MASK, + T_HS_TRAIL_CNT(hs_trail)); + phy_update_bits(inno, i, 0x09, T_HS_EXIT_CNT_MASK, + T_HS_EXIT_CNT(hs_exit)); + phy_update_bits(inno, i, 0x0a, T_CLK_POST_CNT_MASK, + T_CLK_POST_CNT(clk_post)); + phy_update_bits(inno, i, 0x0e, T_CLK_PRE_CNT_MASK, + T_CLK_PRE_CNT(clk_pre)); + phy_update_bits(inno, i, 0x0c, T_WAKEUP_CNT_HI_MASK, + T_WAKEUP_CNT_HI(wakeup >> 8)); + phy_update_bits(inno, i, 0x0d, T_WAKEUP_CNT_LO_MASK, + T_WAKEUP_CNT_LO(wakeup)); + phy_update_bits(inno, i, 0x10, T_TA_GO_CNT_MASK, + T_TA_GO_CNT(ta_go)); + phy_update_bits(inno, i, 0x11, T_TA_SURE_CNT_MASK, + T_TA_SURE_CNT(ta_sure)); + phy_update_bits(inno, i, 0x12, T_TA_WAIT_CNT_MASK, + T_TA_WAIT_CNT(ta_wait)); + } + + /* Enable all lanes on analog part */ + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x00, + LANE_EN_MASK, LANE_EN_CK | LANE_EN_3 | LANE_EN_2 | + LANE_EN_1 | LANE_EN_0); +} + +static void inno_dsidphy_lvds_mode_enable(struct inno_dsidphy *inno) +{ + u8 prediv = 2; + u16 fbdiv = 28; + + /* Sample clock reverse direction */ + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x08, + SAMPLE_CLOCK_DIRECTION_MASK, + SAMPLE_CLOCK_DIRECTION_REVERSE); + + /* Select LVDS mode */ + phy_update_bits(inno, REGISTER_PART_LVDS, 0x03, + MODE_ENABLE_MASK, LVDS_MODE_ENABLE); + /* Configure PLL */ + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x03, + REG_PREDIV_MASK, REG_PREDIV(prediv)); + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x03, + REG_FBDIV_HI_MASK, REG_FBDIV_HI(fbdiv)); + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x04, + REG_FBDIV_LO_MASK, REG_FBDIV_LO(fbdiv)); + phy_update_bits(inno, REGISTER_PART_LVDS, 0x08, 0xff, 0xfc); + /* Enable PLL and Bandgap */ + phy_update_bits(inno, REGISTER_PART_LVDS, 0x0b, + LVDS_PLL_POWER_MASK | LVDS_BANDGAP_POWER_MASK, + LVDS_PLL_POWER_ON | LVDS_BANDGAP_POWER_ON); + + msleep(20); + + /* Reset LVDS digital logic */ + phy_update_bits(inno, REGISTER_PART_LVDS, 0x00, + LVDS_DIGITAL_INTERNAL_RESET_MASK, + LVDS_DIGITAL_INTERNAL_RESET_ENABLE); + udelay(1); + phy_update_bits(inno, REGISTER_PART_LVDS, 0x00, + LVDS_DIGITAL_INTERNAL_RESET_MASK, + LVDS_DIGITAL_INTERNAL_RESET_DISABLE); + /* Enable LVDS digital logic */ + phy_update_bits(inno, REGISTER_PART_LVDS, 0x01, + LVDS_DIGITAL_INTERNAL_ENABLE_MASK, + LVDS_DIGITAL_INTERNAL_ENABLE); + /* Enable LVDS analog driver */ + phy_update_bits(inno, REGISTER_PART_LVDS, 0x0b, + LVDS_LANE_EN_MASK, LVDS_CLK_LANE_EN | + LVDS_DATA_LANE0_EN | LVDS_DATA_LANE1_EN | + LVDS_DATA_LANE2_EN | LVDS_DATA_LANE3_EN); +} + +static int inno_dsidphy_power_on(struct phy *phy) +{ + struct inno_dsidphy *inno = phy_get_drvdata(phy); + + clk_prepare_enable(inno->pclk_phy); + pm_runtime_get_sync(inno->dev); + + /* Bandgap power on */ + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x00, + BANDGAP_POWER_MASK, BANDGAP_POWER_ON); + /* Enable power work */ + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x00, + POWER_WORK_MASK, POWER_WORK_ENABLE); + + switch (inno->mode) { + case PHY_MODE_MIPI_DPHY: + inno_dsidphy_mipi_mode_enable(inno); + break; + case PHY_MODE_LVDS: + inno_dsidphy_lvds_mode_enable(inno); + break; + default: + return -EINVAL; + } + + return 0; +} + +static int inno_dsidphy_power_off(struct phy *phy) +{ + struct inno_dsidphy *inno = phy_get_drvdata(phy); + + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x00, LANE_EN_MASK, 0); + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x01, + REG_LDOPD_MASK | REG_PLLPD_MASK, + REG_LDOPD_POWER_DOWN | REG_PLLPD_POWER_DOWN); + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x00, + POWER_WORK_MASK, POWER_WORK_DISABLE); + phy_update_bits(inno, REGISTER_PART_ANALOG, 0x00, + BANDGAP_POWER_MASK, BANDGAP_POWER_DOWN); + + phy_update_bits(inno, REGISTER_PART_LVDS, 0x0b, LVDS_LANE_EN_MASK, 0); + phy_update_bits(inno, REGISTER_PART_LVDS, 0x01, + LVDS_DIGITAL_INTERNAL_ENABLE_MASK, + LVDS_DIGITAL_INTERNAL_DISABLE); + phy_update_bits(inno, REGISTER_PART_LVDS, 0x0b, + LVDS_PLL_POWER_MASK | LVDS_BANDGAP_POWER_MASK, + LVDS_PLL_POWER_OFF | LVDS_BANDGAP_POWER_DOWN); + + pm_runtime_put(inno->dev); + clk_disable_unprepare(inno->pclk_phy); + + return 0; +} + +static int inno_dsidphy_set_mode(struct phy *phy, enum phy_mode mode, + int submode) +{ + struct inno_dsidphy *inno = phy_get_drvdata(phy); + + switch (mode) { + case PHY_MODE_MIPI_DPHY: + case PHY_MODE_LVDS: + inno->mode = mode; + break; + default: + return -EINVAL; + } + + return 0; +} + +static const struct phy_ops inno_dsidphy_ops = { + .set_mode = inno_dsidphy_set_mode, + .power_on = inno_dsidphy_power_on, + .power_off = inno_dsidphy_power_off, + .owner = THIS_MODULE, +}; + +static unsigned long inno_dsidphy_pll_round_rate(struct inno_dsidphy *inno, + unsigned long prate, + unsigned long rate, + u8 *prediv, u16 *fbdiv) +{ + unsigned long best_freq = 0; + unsigned long fref, fout; + u8 min_prediv, max_prediv; + u8 _prediv, best_prediv = 1; + u16 _fbdiv, best_fbdiv = 1; + u32 min_delta = UINT_MAX; + + /* + * The PLL output frequency can be calculated using a simple formula: + * PLL_Output_Frequency = (FREF / PREDIV * FBDIV) / 2 + * PLL_Output_Frequency: it is equal to DDR-Clock-Frequency * 2 + */ + fref = prate / 2; + if (rate > 1000000000UL) + fout = 1000000000UL; + else + fout = rate; + + /* 5Mhz < Fref / prediv < 40MHz */ + min_prediv = DIV_ROUND_UP(fref, 40000000); + max_prediv = fref / 5000000; + + for (_prediv = min_prediv; _prediv <= max_prediv; _prediv++) { + u64 tmp; + u32 delta; + + tmp = (u64)fout * _prediv; + do_div(tmp, fref); + _fbdiv = tmp; + + /* + * The possible settings of feedback divider are + * 12, 13, 14, 16, ~ 511 + */ + if (_fbdiv == 15) + continue; + + if (_fbdiv < 12 || _fbdiv > 511) + continue; + + tmp = (u64)_fbdiv * fref; + do_div(tmp, _prediv); + + delta = abs(fout - tmp); + if (!delta) { + best_prediv = _prediv; + best_fbdiv = _fbdiv; + best_freq = tmp; + break; + } else if (delta < min_delta) { + best_prediv = _prediv; + best_fbdiv = _fbdiv; + best_freq = tmp; + min_delta = delta; + } + } + + if (best_freq) { + *prediv = best_prediv; + *fbdiv = best_fbdiv; + } + + return best_freq; +} + +static long inno_dsidphy_pll_clk_round_rate(struct clk_hw *hw, + unsigned long rate, + unsigned long *prate) +{ + struct inno_dsidphy *inno = hw_to_inno(hw); + unsigned long fout; + u16 fbdiv = 1; + u8 prediv = 1; + + fout = inno_dsidphy_pll_round_rate(inno, *prate, rate, + &prediv, &fbdiv); + + return fout; +} + +static int inno_dsidphy_pll_clk_set_rate(struct clk_hw *hw, + unsigned long rate, + unsigned long parent_rate) +{ + struct inno_dsidphy *inno = hw_to_inno(hw); + unsigned long fout; + u16 fbdiv = 1; + u8 prediv = 1; + + fout = inno_dsidphy_pll_round_rate(inno, parent_rate, rate, + &prediv, &fbdiv); + + dev_dbg(inno->dev, "fin=%lu, fout=%lu, prediv=%u, fbdiv=%u\n", + parent_rate, fout, prediv, fbdiv); + + inno->pll.prediv = prediv; + inno->pll.fbdiv = fbdiv; + inno->pll.rate = fout; + + return 0; +} + +static unsigned long +inno_dsidphy_pll_clk_recalc_rate(struct clk_hw *hw, unsigned long prate) +{ + struct inno_dsidphy *inno = hw_to_inno(hw); + + /* PLL_Output_Frequency = (FREF / PREDIV * FBDIV) / 2 */ + return (prate / inno->pll.prediv * inno->pll.fbdiv) / 2; +} + +static const struct clk_ops inno_dsidphy_pll_clk_ops = { + .round_rate = inno_dsidphy_pll_clk_round_rate, + .set_rate = inno_dsidphy_pll_clk_set_rate, + .recalc_rate = inno_dsidphy_pll_clk_recalc_rate, +}; + +static int inno_dsidphy_pll_register(struct inno_dsidphy *inno) +{ + struct device *dev = inno->dev; + struct clk *clk; + const char *parent_name; + struct clk_init_data init; + int ret; + + parent_name = __clk_get_name(inno->ref_clk); + + init.name = "mipi_dphy_pll"; + ret = of_property_read_string(dev->of_node, "clock-output-names", + &init.name); + if (ret < 0) + dev_dbg(dev, "phy should set clock-output-names property\n"); + + init.ops = &inno_dsidphy_pll_clk_ops; + init.parent_names = &parent_name; + init.num_parents = 1; + init.flags = 0; + + inno->pll.hw.init = &init; + clk = devm_clk_register(dev, &inno->pll.hw); + if (IS_ERR(clk)) { + ret = PTR_ERR(clk); + dev_err(dev, "failed to register PLL: %d\n", ret); + return ret; + } + + return devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get, + &inno->pll.hw); +} + +static int inno_dsidphy_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct inno_dsidphy *inno; + struct phy_provider *phy_provider; + struct phy *phy; + int ret; + + inno = devm_kzalloc(dev, sizeof(*inno), GFP_KERNEL); + if (!inno) + return -ENOMEM; + + inno->dev = dev; + platform_set_drvdata(pdev, inno); + + inno->phy_base = devm_platform_ioremap_resource(pdev, 0); + if (!inno->phy_base) + return -ENOMEM; + + inno->ref_clk = devm_clk_get(dev, "ref"); + if (IS_ERR(inno->ref_clk)) { + ret = PTR_ERR(inno->ref_clk); + dev_err(dev, "failed to get ref clock: %d\n", ret); + return ret; + } + + inno->pclk_phy = devm_clk_get(dev, "pclk"); + if (IS_ERR(inno->pclk_phy)) { + ret = PTR_ERR(inno->pclk_phy); + dev_err(dev, "failed to get phy pclk: %d\n", ret); + return ret; + } + + inno->rst = devm_reset_control_get(dev, "apb"); + if (IS_ERR(inno->rst)) { + ret = PTR_ERR(inno->rst); + dev_err(dev, "failed to get system reset control: %d\n", ret); + return ret; + } + + phy = devm_phy_create(dev, NULL, &inno_dsidphy_ops); + if (IS_ERR(phy)) { + ret = PTR_ERR(phy); + dev_err(dev, "failed to create phy: %d\n", ret); + return ret; + } + + phy_set_drvdata(phy, inno); + + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); + if (IS_ERR(phy_provider)) { + ret = PTR_ERR(phy_provider); + dev_err(dev, "failed to register phy provider: %d\n", ret); + return ret; + } + + ret = inno_dsidphy_pll_register(inno); + if (ret) + return ret; + + pm_runtime_enable(dev); + + return 0; +} + +static int inno_dsidphy_remove(struct platform_device *pdev) +{ + struct inno_dsidphy *inno = platform_get_drvdata(pdev); + + pm_runtime_disable(inno->dev); + + return 0; +} + +static const struct of_device_id inno_dsidphy_of_match[] = { + { .compatible = "rockchip,px30-dsi-dphy", }, + { .compatible = "rockchip,rk3128-dsi-dphy", }, + { .compatible = "rockchip,rk3368-dsi-dphy", }, + {} +}; +MODULE_DEVICE_TABLE(of, inno_dsidphy_of_match); + +static struct platform_driver inno_dsidphy_driver = { + .driver = { + .name = "inno-dsidphy", + .of_match_table = of_match_ptr(inno_dsidphy_of_match), + }, + .probe = inno_dsidphy_probe, + .remove = inno_dsidphy_remove, +}; +module_platform_driver(inno_dsidphy_driver); + +MODULE_AUTHOR("Wyon Bi <bivvy.bi@rock-chips.com>"); +MODULE_DESCRIPTION("Innosilicon MIPI/LVDS/TTL Video Combo PHY driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c index eae865ff312c..680cc0c8825c 100644 --- a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c +++ b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c @@ -1423,6 +1423,7 @@ static const struct rockchip_usb2phy_cfg rv1108_phy_cfgs[] = { }; static const struct of_device_id rockchip_usb2phy_dt_match[] = { + { .compatible = "rockchip,px30-usb2phy", .data = &rk3328_phy_cfgs }, { .compatible = "rockchip,rk3228-usb2phy", .data = &rk3228_phy_cfgs }, { .compatible = "rockchip,rk3328-usb2phy", .data = &rk3328_phy_cfgs }, { .compatible = "rockchip,rk3366-usb2phy", .data = &rk3366_phy_cfgs }, diff --git a/drivers/phy/tegra/xusb-tegra186.c b/drivers/phy/tegra/xusb-tegra186.c index 6f3afaf9398f..84c27394c181 100644 --- a/drivers/phy/tegra/xusb-tegra186.c +++ b/drivers/phy/tegra/xusb-tegra186.c @@ -857,9 +857,32 @@ static void tegra186_xusb_padctl_remove(struct tegra_xusb_padctl *padctl) { } +static int tegra186_xusb_padctl_vbus_override(struct tegra_xusb_padctl *padctl, + bool status) +{ + u32 value; + + dev_dbg(padctl->dev, "%s vbus override\n", status ? "set" : "clear"); + + value = padctl_readl(padctl, USB2_VBUS_ID); + + if (status) { + value |= VBUS_OVERRIDE; + value &= ~ID_OVERRIDE(~0); + value |= ID_OVERRIDE_FLOATING; + } else { + value &= ~VBUS_OVERRIDE; + } + + padctl_writel(padctl, value, USB2_VBUS_ID); + + return 0; +} + static const struct tegra_xusb_padctl_ops tegra186_xusb_padctl_ops = { .probe = tegra186_xusb_padctl_probe, .remove = tegra186_xusb_padctl_remove, + .vbus_override = tegra186_xusb_padctl_vbus_override, }; static const char * const tegra186_xusb_padctl_supply_names[] = { diff --git a/drivers/phy/tegra/xusb-tegra210.c b/drivers/phy/tegra/xusb-tegra210.c index 0c0df6897a3b..394913bb2f20 100644 --- a/drivers/phy/tegra/xusb-tegra210.c +++ b/drivers/phy/tegra/xusb-tegra210.c @@ -39,7 +39,10 @@ #define XUSB_PADCTL_USB2_PAD_MUX_USB2_BIAS_PAD_XUSB 0x1 #define XUSB_PADCTL_USB2_PORT_CAP 0x008 +#define XUSB_PADCTL_USB2_PORT_CAP_PORTX_CAP_DISABLED(x) (0x0 << ((x) * 4)) #define XUSB_PADCTL_USB2_PORT_CAP_PORTX_CAP_HOST(x) (0x1 << ((x) * 4)) +#define XUSB_PADCTL_USB2_PORT_CAP_PORTX_CAP_DEVICE(x) (0x2 << ((x) * 4)) +#define XUSB_PADCTL_USB2_PORT_CAP_PORTX_CAP_OTG(x) (0x3 << ((x) * 4)) #define XUSB_PADCTL_USB2_PORT_CAP_PORTX_CAP_MASK(x) (0x3 << ((x) * 4)) #define XUSB_PADCTL_SS_PORT_MAP 0x014 @@ -47,6 +50,7 @@ #define XUSB_PADCTL_SS_PORT_MAP_PORTX_MAP_SHIFT(x) ((x) * 5) #define XUSB_PADCTL_SS_PORT_MAP_PORTX_MAP_MASK(x) (0x7 << ((x) * 5)) #define XUSB_PADCTL_SS_PORT_MAP_PORTX_MAP(x, v) (((v) & 0x7) << ((x) * 5)) +#define XUSB_PADCTL_SS_PORT_MAP_PORT_DISABLED 0x7 #define XUSB_PADCTL_ELPG_PROGRAM1 0x024 #define XUSB_PADCTL_ELPG_PROGRAM1_AUX_MUX_LP0_VCORE_DOWN (1 << 31) @@ -61,9 +65,14 @@ #define XUSB_PADCTL_USB3_PAD_MUX_PCIE_IDDQ_DISABLE(x) (1 << (1 + (x))) #define XUSB_PADCTL_USB3_PAD_MUX_SATA_IDDQ_DISABLE(x) (1 << (8 + (x))) +#define XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPADX_CTL0(x) (0x080 + (x) * 0x40) +#define XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL0_ZIP (1 << 18) +#define XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL0_ZIN (1 << 22) + #define XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPADX_CTL1(x) (0x084 + (x) * 0x40) #define XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL1_VREG_LEV_SHIFT 7 #define XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL1_VREG_LEV_MASK 0x3 +#define XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL1_VREG_LEV_VAL 0x1 #define XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL1_VREG_FIX18 (1 << 6) #define XUSB_PADCTL_USB2_OTG_PADX_CTL0(x) (0x088 + (x) * 0x40) @@ -222,6 +231,12 @@ #define XUSB_PADCTL_UPHY_USB3_PADX_ECTL6(x) (0xa74 + (x) * 0x40) #define XUSB_PADCTL_UPHY_USB3_PAD_ECTL6_RX_EQ_CTRL_H_VAL 0xfcf01368 +#define XUSB_PADCTL_USB2_VBUS_ID 0xc60 +#define XUSB_PADCTL_USB2_VBUS_ID_OVERRIDE_VBUS_ON (1 << 14) +#define XUSB_PADCTL_USB2_VBUS_ID_OVERRIDE_SHIFT 18 +#define XUSB_PADCTL_USB2_VBUS_ID_OVERRIDE_MASK 0xf +#define XUSB_PADCTL_USB2_VBUS_ID_OVERRIDE_FLOATING 8 + struct tegra210_xusb_fuse_calibration { u32 hs_curr_level[4]; u32 hs_term_range_adj; @@ -940,6 +955,34 @@ static int tegra210_usb2_phy_power_on(struct phy *phy) priv = to_tegra210_xusb_padctl(padctl); + if (port->usb3_port_fake != -1) { + value = padctl_readl(padctl, XUSB_PADCTL_SS_PORT_MAP); + value &= ~XUSB_PADCTL_SS_PORT_MAP_PORTX_MAP_MASK( + port->usb3_port_fake); + value |= XUSB_PADCTL_SS_PORT_MAP_PORTX_MAP( + port->usb3_port_fake, index); + padctl_writel(padctl, value, XUSB_PADCTL_SS_PORT_MAP); + + value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM1); + value &= ~XUSB_PADCTL_ELPG_PROGRAM1_SSPX_ELPG_VCORE_DOWN( + port->usb3_port_fake); + padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM1); + + usleep_range(100, 200); + + value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM1); + value &= ~XUSB_PADCTL_ELPG_PROGRAM1_SSPX_ELPG_CLAMP_EN_EARLY( + port->usb3_port_fake); + padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM1); + + usleep_range(100, 200); + + value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM1); + value &= ~XUSB_PADCTL_ELPG_PROGRAM1_SSPX_ELPG_CLAMP_EN( + port->usb3_port_fake); + padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM1); + } + value = padctl_readl(padctl, XUSB_PADCTL_USB2_BIAS_PAD_CTL0); value &= ~((XUSB_PADCTL_USB2_BIAS_PAD_CTL0_HS_SQUELCH_LEVEL_MASK << XUSB_PADCTL_USB2_BIAS_PAD_CTL0_HS_SQUELCH_LEVEL_SHIFT) | @@ -957,7 +1000,14 @@ static int tegra210_usb2_phy_power_on(struct phy *phy) value = padctl_readl(padctl, XUSB_PADCTL_USB2_PORT_CAP); value &= ~XUSB_PADCTL_USB2_PORT_CAP_PORTX_CAP_MASK(index); - value |= XUSB_PADCTL_USB2_PORT_CAP_PORTX_CAP_HOST(index); + if (port->mode == USB_DR_MODE_UNKNOWN) + value |= XUSB_PADCTL_USB2_PORT_CAP_PORTX_CAP_DISABLED(index); + else if (port->mode == USB_DR_MODE_PERIPHERAL) + value |= XUSB_PADCTL_USB2_PORT_CAP_PORTX_CAP_DEVICE(index); + else if (port->mode == USB_DR_MODE_HOST) + value |= XUSB_PADCTL_USB2_PORT_CAP_PORTX_CAP_HOST(index); + else if (port->mode == USB_DR_MODE_OTG) + value |= XUSB_PADCTL_USB2_PORT_CAP_PORTX_CAP_OTG(index); padctl_writel(padctl, value, XUSB_PADCTL_USB2_PORT_CAP); value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL0(index)); @@ -989,7 +1039,12 @@ static int tegra210_usb2_phy_power_on(struct phy *phy) XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPADX_CTL1(index)); value &= ~(XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL1_VREG_LEV_MASK << XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL1_VREG_LEV_SHIFT); - value |= XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL1_VREG_FIX18; + if (port->mode == USB_DR_MODE_HOST) + value |= XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL1_VREG_FIX18; + else + value |= + XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL1_VREG_LEV_VAL << + XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL1_VREG_LEV_SHIFT; padctl_writel(padctl, value, XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPADX_CTL1(index)); @@ -1062,6 +1117,32 @@ static int tegra210_usb2_phy_power_off(struct phy *phy) mutex_lock(&padctl->lock); + if (port->usb3_port_fake != -1) { + value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM1); + value |= XUSB_PADCTL_ELPG_PROGRAM1_SSPX_ELPG_CLAMP_EN_EARLY( + port->usb3_port_fake); + padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM1); + + usleep_range(100, 200); + + value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM1); + value |= XUSB_PADCTL_ELPG_PROGRAM1_SSPX_ELPG_CLAMP_EN( + port->usb3_port_fake); + padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM1); + + usleep_range(250, 350); + + value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM1); + value |= XUSB_PADCTL_ELPG_PROGRAM1_SSPX_ELPG_VCORE_DOWN( + port->usb3_port_fake); + padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM1); + + value = padctl_readl(padctl, XUSB_PADCTL_SS_PORT_MAP); + value |= XUSB_PADCTL_SS_PORT_MAP_PORTX_MAP(port->usb3_port_fake, + XUSB_PADCTL_SS_PORT_MAP_PORT_DISABLED); + padctl_writel(padctl, value, XUSB_PADCTL_SS_PORT_MAP); + } + if (WARN_ON(pad->enable == 0)) goto out; @@ -1225,13 +1306,10 @@ static int tegra210_hsic_phy_power_on(struct phy *phy) struct tegra_xusb_hsic_lane *hsic = to_hsic_lane(lane); struct tegra_xusb_hsic_pad *pad = to_hsic_pad(lane->pad); struct tegra_xusb_padctl *padctl = lane->pad->padctl; - struct tegra210_xusb_padctl *priv; unsigned int index = lane->index; u32 value; int err; - priv = to_tegra210_xusb_padctl(padctl); - err = regulator_enable(pad->supply); if (err) return err; @@ -1945,6 +2023,52 @@ static const struct tegra_xusb_port_ops tegra210_usb3_port_ops = { .map = tegra210_usb3_port_map, }; +static int tegra210_xusb_padctl_vbus_override(struct tegra_xusb_padctl *padctl, + bool status) +{ + u32 value; + + dev_dbg(padctl->dev, "%s vbus override\n", status ? "set" : "clear"); + + value = padctl_readl(padctl, XUSB_PADCTL_USB2_VBUS_ID); + + if (status) { + value |= XUSB_PADCTL_USB2_VBUS_ID_OVERRIDE_VBUS_ON; + value &= ~(XUSB_PADCTL_USB2_VBUS_ID_OVERRIDE_MASK << + XUSB_PADCTL_USB2_VBUS_ID_OVERRIDE_SHIFT); + value |= XUSB_PADCTL_USB2_VBUS_ID_OVERRIDE_FLOATING << + XUSB_PADCTL_USB2_VBUS_ID_OVERRIDE_SHIFT; + } else { + value &= ~XUSB_PADCTL_USB2_VBUS_ID_OVERRIDE_VBUS_ON; + } + + padctl_writel(padctl, value, XUSB_PADCTL_USB2_VBUS_ID); + + return 0; +} + +static int tegra210_utmi_port_reset(struct phy *phy) +{ + struct tegra_xusb_padctl *padctl; + struct tegra_xusb_lane *lane; + u32 value; + + lane = phy_get_drvdata(phy); + padctl = lane->pad->padctl; + + value = padctl_readl(padctl, + XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPADX_CTL0(lane->index)); + + if ((value & XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL0_ZIP) || + (value & XUSB_PADCTL_USB2_BATTERY_CHRG_OTGPAD_CTL0_ZIN)) { + tegra210_xusb_padctl_vbus_override(padctl, false); + tegra210_xusb_padctl_vbus_override(padctl, true); + return 1; + } + + return 0; +} + static int tegra210_xusb_read_fuse_calibration(struct tegra210_xusb_fuse_calibration *fuse) { @@ -2007,6 +2131,8 @@ static const struct tegra_xusb_padctl_ops tegra210_xusb_padctl_ops = { .remove = tegra210_xusb_padctl_remove, .usb3_set_lfps_detect = tegra210_usb3_set_lfps_detect, .hsic_set_idle = tegra210_hsic_set_idle, + .vbus_override = tegra210_xusb_padctl_vbus_override, + .utmi_port_reset = tegra210_utmi_port_reset, }; static const char * const tegra210_xusb_padctl_supply_names[] = { @@ -2036,6 +2162,7 @@ const struct tegra_xusb_padctl_soc tegra210_xusb_padctl_soc = { .ops = &tegra210_xusb_padctl_ops, .supply_names = tegra210_xusb_padctl_supply_names, .num_supplies = ARRAY_SIZE(tegra210_xusb_padctl_supply_names), + .need_fake_usb3_port = true, }; EXPORT_SYMBOL_GPL(tegra210_xusb_padctl_soc); diff --git a/drivers/phy/tegra/xusb.c b/drivers/phy/tegra/xusb.c index 2ea8497af82a..f98ec3922c02 100644 --- a/drivers/phy/tegra/xusb.c +++ b/drivers/phy/tegra/xusb.c @@ -800,9 +800,62 @@ static void __tegra_xusb_remove_ports(struct tegra_xusb_padctl *padctl) } } +static int tegra_xusb_find_unused_usb3_port(struct tegra_xusb_padctl *padctl) +{ + struct device_node *np; + unsigned int i; + + for (i = 0; i < padctl->soc->ports.usb3.count; i++) { + np = tegra_xusb_find_port_node(padctl, "usb3", i); + if (!np || !of_device_is_available(np)) + return i; + } + + return -ENODEV; +} + +static bool tegra_xusb_port_is_companion(struct tegra_xusb_usb2_port *usb2) +{ + unsigned int i; + struct tegra_xusb_usb3_port *usb3; + struct tegra_xusb_padctl *padctl = usb2->base.padctl; + + for (i = 0; i < padctl->soc->ports.usb3.count; i++) { + usb3 = tegra_xusb_find_usb3_port(padctl, i); + if (usb3 && usb3->port == usb2->base.index) + return true; + } + + return false; +} + +static int tegra_xusb_update_usb3_fake_port(struct tegra_xusb_usb2_port *usb2) +{ + int fake; + + /* Disable usb3_port_fake usage by default and assign if needed */ + usb2->usb3_port_fake = -1; + + if ((usb2->mode == USB_DR_MODE_OTG || + usb2->mode == USB_DR_MODE_PERIPHERAL) && + !tegra_xusb_port_is_companion(usb2)) { + fake = tegra_xusb_find_unused_usb3_port(usb2->base.padctl); + if (fake < 0) { + dev_err(&usb2->base.dev, "no unused USB3 ports available\n"); + return -ENODEV; + } + + dev_dbg(&usb2->base.dev, "Found unused usb3 port: %d\n", fake); + usb2->usb3_port_fake = fake; + } + + return 0; +} + static int tegra_xusb_setup_ports(struct tegra_xusb_padctl *padctl) { struct tegra_xusb_port *port; + struct tegra_xusb_usb2_port *usb2; unsigned int i; int err = 0; @@ -832,6 +885,18 @@ static int tegra_xusb_setup_ports(struct tegra_xusb_padctl *padctl) goto remove_ports; } + if (padctl->soc->need_fake_usb3_port) { + for (i = 0; i < padctl->soc->ports.usb2.count; i++) { + usb2 = tegra_xusb_find_usb2_port(padctl, i); + if (!usb2) + continue; + + err = tegra_xusb_update_usb3_fake_port(usb2); + if (err < 0) + goto remove_ports; + } + } + list_for_each_entry(port, &padctl->ports, list) { err = port->ops->enable(port); if (err < 0) @@ -862,7 +927,6 @@ static int tegra_xusb_padctl_probe(struct platform_device *pdev) struct tegra_xusb_padctl *padctl; const struct of_device_id *match; struct resource *res; - unsigned int i; int err; /* for backwards compatibility with old device trees */ @@ -907,8 +971,9 @@ static int tegra_xusb_padctl_probe(struct platform_device *pdev) goto remove; } - for (i = 0; i < padctl->soc->num_supplies; i++) - padctl->supplies[i].supply = padctl->soc->supply_names[i]; + regulator_bulk_set_supply_names(padctl->supplies, + padctl->soc->supply_names, + padctl->soc->num_supplies); err = devm_regulator_bulk_get(&pdev->dev, padctl->soc->num_supplies, padctl->supplies); @@ -1056,6 +1121,28 @@ int tegra_xusb_padctl_usb3_set_lfps_detect(struct tegra_xusb_padctl *padctl, } EXPORT_SYMBOL_GPL(tegra_xusb_padctl_usb3_set_lfps_detect); +int tegra_xusb_padctl_set_vbus_override(struct tegra_xusb_padctl *padctl, + bool val) +{ + if (padctl->soc->ops->vbus_override) + return padctl->soc->ops->vbus_override(padctl, val); + + return -ENOTSUPP; +} +EXPORT_SYMBOL_GPL(tegra_xusb_padctl_set_vbus_override); + +int tegra_phy_xusb_utmi_port_reset(struct phy *phy) +{ + struct tegra_xusb_lane *lane = phy_get_drvdata(phy); + struct tegra_xusb_padctl *padctl = lane->pad->padctl; + + if (padctl->soc->ops->utmi_port_reset) + return padctl->soc->ops->utmi_port_reset(phy); + + return -ENOTSUPP; +} +EXPORT_SYMBOL_GPL(tegra_phy_xusb_utmi_port_reset); + MODULE_AUTHOR("Thierry Reding <treding@nvidia.com>"); MODULE_DESCRIPTION("Tegra XUSB Pad Controller driver"); MODULE_LICENSE("GPL v2"); diff --git a/drivers/phy/tegra/xusb.h b/drivers/phy/tegra/xusb.h index 093076ca27fd..da94fcce6307 100644 --- a/drivers/phy/tegra/xusb.h +++ b/drivers/phy/tegra/xusb.h @@ -291,6 +291,7 @@ struct tegra_xusb_usb2_port { struct regulator *supply; enum usb_dr_mode mode; bool internal; + int usb3_port_fake; }; static inline struct tegra_xusb_usb2_port * @@ -372,6 +373,8 @@ struct tegra_xusb_padctl_ops { unsigned int index, bool idle); int (*usb3_set_lfps_detect)(struct tegra_xusb_padctl *padctl, unsigned int index, bool enable); + int (*vbus_override)(struct tegra_xusb_padctl *padctl, bool set); + int (*utmi_port_reset)(struct phy *phy); }; struct tegra_xusb_padctl_soc { @@ -389,6 +392,7 @@ struct tegra_xusb_padctl_soc { const char * const *supply_names; unsigned int num_supplies; + bool need_fake_usb3_port; }; struct tegra_xusb_padctl { diff --git a/drivers/phy/ti/Kconfig b/drivers/phy/ti/Kconfig index c3fa1840f8de..174888609779 100644 --- a/drivers/phy/ti/Kconfig +++ b/drivers/phy/ti/Kconfig @@ -90,8 +90,8 @@ config TWL4030_USB config PHY_TI_GMII_SEL tristate - default y if TI_CPSW=y - depends on TI_CPSW || COMPILE_TEST + default y if TI_CPSW=y || TI_CPSW_SWITCHDEV=y + depends on TI_CPSW || TI_CPSW_SWITCHDEV || COMPILE_TEST select GENERIC_PHY select REGMAP default m diff --git a/drivers/phy/ti/phy-dm816x-usb.c b/drivers/phy/ti/phy-dm816x-usb.c index cbcce7cf0028..26f194779064 100644 --- a/drivers/phy/ti/phy-dm816x-usb.c +++ b/drivers/phy/ti/phy-dm816x-usb.c @@ -189,7 +189,6 @@ static int dm816x_usb_phy_probe(struct platform_device *pdev) struct phy_provider *phy_provider; struct usb_otg *otg; const struct of_device_id *of_id; - const struct usb_phy_data *phy_data; int error; of_id = of_match_device(of_match_ptr(dm816x_usb_phy_id_table), @@ -220,8 +219,6 @@ static int dm816x_usb_phy_probe(struct platform_device *pdev) if (phy->usbphy_ctrl == 0x2c) phy->instance = 1; - phy_data = of_id->data; - otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL); if (!otg) return -ENOMEM; diff --git a/drivers/phy/ti/phy-gmii-sel.c b/drivers/phy/ti/phy-gmii-sel.c index a52c5bb35033..a28bd15297f5 100644 --- a/drivers/phy/ti/phy-gmii-sel.c +++ b/drivers/phy/ti/phy-gmii-sel.c @@ -69,11 +69,11 @@ static int phy_gmii_sel_mode(struct phy *phy, enum phy_mode mode, int submode) break; case PHY_INTERFACE_MODE_RGMII: + case PHY_INTERFACE_MODE_RGMII_RXID: gmii_sel_mode = AM33XX_GMII_SEL_MODE_RGMII; break; case PHY_INTERFACE_MODE_RGMII_ID: - case PHY_INTERFACE_MODE_RGMII_RXID: case PHY_INTERFACE_MODE_RGMII_TXID: gmii_sel_mode = AM33XX_GMII_SEL_MODE_RGMII; rgmii_id = 1; |