diff options
Diffstat (limited to 'drivers/scsi/pm8001/pm8001_init.c')
| -rw-r--r-- | drivers/scsi/pm8001/pm8001_init.c | 900 |
1 files changed, 900 insertions, 0 deletions
diff --git a/drivers/scsi/pm8001/pm8001_init.c b/drivers/scsi/pm8001/pm8001_init.c new file mode 100644 index 000000000000..c2f1032496cb --- /dev/null +++ b/drivers/scsi/pm8001/pm8001_init.c @@ -0,0 +1,900 @@ +/* + * PMC-Sierra SPC 8001 SAS/SATA based host adapters driver + * + * Copyright (c) 2008-2009 USI Co., Ltd. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + */ + +#include "pm8001_sas.h" +#include "pm8001_chips.h" + +static struct scsi_transport_template *pm8001_stt; + +static const struct pm8001_chip_info pm8001_chips[] = { + [chip_8001] = { 8, &pm8001_8001_dispatch,}, +}; +static int pm8001_id; + +LIST_HEAD(hba_list); + +/** + * The main structure which LLDD must register for scsi core. + */ +static struct scsi_host_template pm8001_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .queuecommand = sas_queuecommand, + .target_alloc = sas_target_alloc, + .slave_configure = pm8001_slave_configure, + .slave_destroy = sas_slave_destroy, + .scan_finished = pm8001_scan_finished, + .scan_start = pm8001_scan_start, + .change_queue_depth = sas_change_queue_depth, + .change_queue_type = sas_change_queue_type, + .bios_param = sas_bios_param, + .can_queue = 1, + .cmd_per_lun = 1, + .this_id = -1, + .sg_tablesize = SG_ALL, + .max_sectors = SCSI_DEFAULT_MAX_SECTORS, + .use_clustering = ENABLE_CLUSTERING, + .eh_device_reset_handler = sas_eh_device_reset_handler, + .eh_bus_reset_handler = sas_eh_bus_reset_handler, + .slave_alloc = pm8001_slave_alloc, + .target_destroy = sas_target_destroy, + .ioctl = sas_ioctl, + .shost_attrs = pm8001_host_attrs, +}; + +/** + * Sas layer call this function to execute specific task. + */ +static struct sas_domain_function_template pm8001_transport_ops = { + .lldd_dev_found = pm8001_dev_found, + .lldd_dev_gone = pm8001_dev_gone, + + .lldd_execute_task = pm8001_queue_command, + .lldd_control_phy = pm8001_phy_control, + + .lldd_abort_task = pm8001_abort_task, + .lldd_abort_task_set = pm8001_abort_task_set, + .lldd_clear_aca = pm8001_clear_aca, + .lldd_clear_task_set = pm8001_clear_task_set, + .lldd_I_T_nexus_reset = pm8001_I_T_nexus_reset, + .lldd_lu_reset = pm8001_lu_reset, + .lldd_query_task = pm8001_query_task, +}; + +/** + *pm8001_phy_init - initiate our adapter phys + *@pm8001_ha: our hba structure. + *@phy_id: phy id. + */ +static void __devinit pm8001_phy_init(struct pm8001_hba_info *pm8001_ha, + int phy_id) +{ + struct pm8001_phy *phy = &pm8001_ha->phy[phy_id]; + struct asd_sas_phy *sas_phy = &phy->sas_phy; + phy->phy_state = 0; + phy->pm8001_ha = pm8001_ha; + sas_phy->enabled = (phy_id < pm8001_ha->chip->n_phy) ? 1 : 0; + sas_phy->class = SAS; + sas_phy->iproto = SAS_PROTOCOL_ALL; + sas_phy->tproto = 0; + sas_phy->type = PHY_TYPE_PHYSICAL; + sas_phy->role = PHY_ROLE_INITIATOR; + sas_phy->oob_mode = OOB_NOT_CONNECTED; + sas_phy->linkrate = SAS_LINK_RATE_UNKNOWN; + sas_phy->id = phy_id; + sas_phy->sas_addr = &pm8001_ha->sas_addr[0]; + sas_phy->frame_rcvd = &phy->frame_rcvd[0]; + sas_phy->ha = (struct sas_ha_struct *)pm8001_ha->shost->hostdata; + sas_phy->lldd_phy = phy; +} + +/** + *pm8001_free - free hba + *@pm8001_ha: our hba structure. + * + */ +static void pm8001_free(struct pm8001_hba_info *pm8001_ha) +{ + int i; + struct pm8001_wq *wq; + + if (!pm8001_ha) + return; + + for (i = 0; i < USI_MAX_MEMCNT; i++) { + if (pm8001_ha->memoryMap.region[i].virt_ptr != NULL) { + pci_free_consistent(pm8001_ha->pdev, + pm8001_ha->memoryMap.region[i].element_size, + pm8001_ha->memoryMap.region[i].virt_ptr, + pm8001_ha->memoryMap.region[i].phys_addr); + } + } + PM8001_CHIP_DISP->chip_iounmap(pm8001_ha); + if (pm8001_ha->shost) + scsi_host_put(pm8001_ha->shost); + list_for_each_entry(wq, &pm8001_ha->wq_list, entry) + cancel_delayed_work(&wq->work_q); + kfree(pm8001_ha->tags); + kfree(pm8001_ha); +} + +#ifdef PM8001_USE_TASKLET +static void pm8001_tasklet(unsigned long opaque) +{ + struct pm8001_hba_info *pm8001_ha; + pm8001_ha = (struct pm8001_hba_info *)opaque;; + if (unlikely(!pm8001_ha)) + BUG_ON(1); + PM8001_CHIP_DISP->isr(pm8001_ha); +} +#endif + + + /** + * pm8001_interrupt - when HBA originate a interrupt,we should invoke this + * dispatcher to handle each case. + * @irq: irq number. + * @opaque: the passed general host adapter struct + */ +static irqreturn_t pm8001_interrupt(int irq, void *opaque) +{ + struct pm8001_hba_info *pm8001_ha; + irqreturn_t ret = IRQ_HANDLED; + struct sas_ha_struct *sha = opaque; + pm8001_ha = sha->lldd_ha; + if (unlikely(!pm8001_ha)) + return IRQ_NONE; + if (!PM8001_CHIP_DISP->is_our_interupt(pm8001_ha)) + return IRQ_NONE; +#ifdef PM8001_USE_TASKLET + tasklet_schedule(&pm8001_ha->tasklet); +#else + ret = PM8001_CHIP_DISP->isr(pm8001_ha); +#endif + return ret; +} + +/** + * pm8001_alloc - initiate our hba structure and 6 DMAs area. + * @pm8001_ha:our hba structure. + * + */ +static int __devinit pm8001_alloc(struct pm8001_hba_info *pm8001_ha) +{ + int i; + spin_lock_init(&pm8001_ha->lock); + for (i = 0; i < pm8001_ha->chip->n_phy; i++) { + pm8001_phy_init(pm8001_ha, i); + pm8001_ha->port[i].wide_port_phymap = 0; + pm8001_ha->port[i].port_attached = 0; + pm8001_ha->port[i].port_state = 0; + INIT_LIST_HEAD(&pm8001_ha->port[i].list); + } + + pm8001_ha->tags = kzalloc(PM8001_MAX_CCB, GFP_KERNEL); + if (!pm8001_ha->tags) + goto err_out; + /* MPI Memory region 1 for AAP Event Log for fw */ + pm8001_ha->memoryMap.region[AAP1].num_elements = 1; + pm8001_ha->memoryMap.region[AAP1].element_size = PM8001_EVENT_LOG_SIZE; + pm8001_ha->memoryMap.region[AAP1].total_len = PM8001_EVENT_LOG_SIZE; + pm8001_ha->memoryMap.region[AAP1].alignment = 32; + + /* MPI Memory region 2 for IOP Event Log for fw */ + pm8001_ha->memoryMap.region[IOP].num_elements = 1; + pm8001_ha->memoryMap.region[IOP].element_size = PM8001_EVENT_LOG_SIZE; + pm8001_ha->memoryMap.region[IOP].total_len = PM8001_EVENT_LOG_SIZE; + pm8001_ha->memoryMap.region[IOP].alignment = 32; + + /* MPI Memory region 3 for consumer Index of inbound queues */ + pm8001_ha->memoryMap.region[CI].num_elements = 1; + pm8001_ha->memoryMap.region[CI].element_size = 4; + pm8001_ha->memoryMap.region[CI].total_len = 4; + pm8001_ha->memoryMap.region[CI].alignment = 4; + + /* MPI Memory region 4 for producer Index of outbound queues */ + pm8001_ha->memoryMap.region[PI].num_elements = 1; + pm8001_ha->memoryMap.region[PI].element_size = 4; + pm8001_ha->memoryMap.region[PI].total_len = 4; + pm8001_ha->memoryMap.region[PI].alignment = 4; + + /* MPI Memory region 5 inbound queues */ + pm8001_ha->memoryMap.region[IB].num_elements = 256; + pm8001_ha->memoryMap.region[IB].element_size = 64; + pm8001_ha->memoryMap.region[IB].total_len = 256 * 64; + pm8001_ha->memoryMap.region[IB].alignment = 64; + + /* MPI Memory region 6 inbound queues */ + pm8001_ha->memoryMap.region[OB].num_elements = 256; + pm8001_ha->memoryMap.region[OB].element_size = 64; + pm8001_ha->memoryMap.region[OB].total_len = 256 * 64; + pm8001_ha->memoryMap.region[OB].alignment = 64; + + /* Memory region write DMA*/ + pm8001_ha->memoryMap.region[NVMD].num_elements = 1; + pm8001_ha->memoryMap.region[NVMD].element_size = 4096; + pm8001_ha->memoryMap.region[NVMD].total_len = 4096; + /* Memory region for devices*/ + pm8001_ha->memoryMap.region[DEV_MEM].num_elements = 1; + pm8001_ha->memoryMap.region[DEV_MEM].element_size = PM8001_MAX_DEVICES * + sizeof(struct pm8001_device); + pm8001_ha->memoryMap.region[DEV_MEM].total_len = PM8001_MAX_DEVICES * + sizeof(struct pm8001_device); + + /* Memory region for ccb_info*/ + pm8001_ha->memoryMap.region[CCB_MEM].num_elements = 1; + pm8001_ha->memoryMap.region[CCB_MEM].element_size = PM8001_MAX_CCB * + sizeof(struct pm8001_ccb_info); + pm8001_ha->memoryMap.region[CCB_MEM].total_len = PM8001_MAX_CCB * + sizeof(struct pm8001_ccb_info); + + for (i = 0; i < USI_MAX_MEMCNT; i++) { + if (pm8001_mem_alloc(pm8001_ha->pdev, + &pm8001_ha->memoryMap.region[i].virt_ptr, + &pm8001_ha->memoryMap.region[i].phys_addr, + &pm8001_ha->memoryMap.region[i].phys_addr_hi, + &pm8001_ha->memoryMap.region[i].phys_addr_lo, + pm8001_ha->memoryMap.region[i].total_len, + pm8001_ha->memoryMap.region[i].alignment) != 0) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("Mem%d alloc failed\n", + i)); + goto err_out; + } + } + + pm8001_ha->devices = pm8001_ha->memoryMap.region[DEV_MEM].virt_ptr; + for (i = 0; i < PM8001_MAX_DEVICES; i++) { + pm8001_ha->devices[i].dev_type = NO_DEVICE; + pm8001_ha->devices[i].id = i; + pm8001_ha->devices[i].device_id = PM8001_MAX_DEVICES; + pm8001_ha->devices[i].running_req = 0; + } + pm8001_ha->ccb_info = pm8001_ha->memoryMap.region[CCB_MEM].virt_ptr; + for (i = 0; i < PM8001_MAX_CCB; i++) { + pm8001_ha->ccb_info[i].ccb_dma_handle = + pm8001_ha->memoryMap.region[CCB_MEM].phys_addr + + i * sizeof(struct pm8001_ccb_info); + pm8001_ha->ccb_info[i].task = NULL; + pm8001_ha->ccb_info[i].ccb_tag = 0xffffffff; + pm8001_ha->ccb_info[i].device = NULL; + ++pm8001_ha->tags_num; + } + pm8001_ha->flags = PM8001F_INIT_TIME; + /* Initialize tags */ + pm8001_tag_init(pm8001_ha); + return 0; +err_out: + return 1; +} + +/** + * pm8001_ioremap - remap the pci high physical address to kernal virtual + * address so that we can access them. + * @pm8001_ha:our hba structure. + */ +static int pm8001_ioremap(struct pm8001_hba_info *pm8001_ha) +{ + u32 bar; + u32 logicalBar = 0; + struct pci_dev *pdev; + + pdev = pm8001_ha->pdev; + /* map pci mem (PMC pci base 0-3)*/ + for (bar = 0; bar < 6; bar++) { + /* + ** logical BARs for SPC: + ** bar 0 and 1 - logical BAR0 + ** bar 2 and 3 - logical BAR1 + ** bar4 - logical BAR2 + ** bar5 - logical BAR3 + ** Skip the appropriate assignments: + */ + if ((bar == 1) || (bar == 3)) + continue; + if (pci_resource_flags(pdev, bar) & IORESOURCE_MEM) { + pm8001_ha->io_mem[logicalBar].membase = + pci_resource_start(pdev, bar); + pm8001_ha->io_mem[logicalBar].membase &= + (u32)PCI_BASE_ADDRESS_MEM_MASK; + pm8001_ha->io_mem[logicalBar].memsize = + pci_resource_len(pdev, bar); + pm8001_ha->io_mem[logicalBar].memvirtaddr = + ioremap(pm8001_ha->io_mem[logicalBar].membase, + pm8001_ha->io_mem[logicalBar].memsize); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("PCI: bar %d, logicalBar %d " + "virt_addr=%lx,len=%d\n", bar, logicalBar, + (unsigned long) + pm8001_ha->io_mem[logicalBar].memvirtaddr, + pm8001_ha->io_mem[logicalBar].memsize)); + } else { + pm8001_ha->io_mem[logicalBar].membase = 0; + pm8001_ha->io_mem[logicalBar].memsize = 0; + pm8001_ha->io_mem[logicalBar].memvirtaddr = 0; + } + logicalBar++; + } + return 0; +} + +/** + * pm8001_pci_alloc - initialize our ha card structure + * @pdev: pci device. + * @ent: ent + * @shost: scsi host struct which has been initialized before. + */ +static struct pm8001_hba_info *__devinit +pm8001_pci_alloc(struct pci_dev *pdev, u32 chip_id, struct Scsi_Host *shost) +{ + struct pm8001_hba_info *pm8001_ha; + struct sas_ha_struct *sha = SHOST_TO_SAS_HA(shost); + + + pm8001_ha = sha->lldd_ha; + if (!pm8001_ha) + return NULL; + + pm8001_ha->pdev = pdev; + pm8001_ha->dev = &pdev->dev; + pm8001_ha->chip_id = chip_id; + pm8001_ha->chip = &pm8001_chips[pm8001_ha->chip_id]; + pm8001_ha->irq = pdev->irq; + pm8001_ha->sas = sha; + pm8001_ha->shost = shost; + pm8001_ha->id = pm8001_id++; + INIT_LIST_HEAD(&pm8001_ha->wq_list); + pm8001_ha->logging_level = 0x01; + sprintf(pm8001_ha->name, "%s%d", DRV_NAME, pm8001_ha->id); +#ifdef PM8001_USE_TASKLET + tasklet_init(&pm8001_ha->tasklet, pm8001_tasklet, + (unsigned long)pm8001_ha); +#endif + pm8001_ioremap(pm8001_ha); + if (!pm8001_alloc(pm8001_ha)) + return pm8001_ha; + pm8001_free(pm8001_ha); + return NULL; +} + +/** + * pci_go_44 - pm8001 specified, its DMA is 44 bit rather than 64 bit + * @pdev: pci device. + */ +static int pci_go_44(struct pci_dev *pdev) +{ + int rc; + + if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(44))) { + rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(44)); + if (rc) { + rc = pci_set_consistent_dma_mask(pdev, + DMA_BIT_MASK(32)); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "44-bit DMA enable failed\n"); + return rc; + } + } + } else { + rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "32-bit DMA enable failed\n"); + return rc; + } + rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32)); + if (rc) { + dev_printk(KERN_ERR, &pdev->dev, + "32-bit consistent DMA enable failed\n"); + return rc; + } + } + return rc; +} + +/** + * pm8001_prep_sas_ha_init - allocate memory in general hba struct && init them. + * @shost: scsi host which has been allocated outside. + * @chip_info: our ha struct. + */ +static int __devinit pm8001_prep_sas_ha_init(struct Scsi_Host * shost, + const struct pm8001_chip_info *chip_info) +{ + int phy_nr, port_nr; + struct asd_sas_phy **arr_phy; + struct asd_sas_port **arr_port; + struct sas_ha_struct *sha = SHOST_TO_SAS_HA(shost); + + phy_nr = chip_info->n_phy; + port_nr = phy_nr; + memset(sha, 0x00, sizeof(*sha)); + arr_phy = kcalloc(phy_nr, sizeof(void *), GFP_KERNEL); + if (!arr_phy) + goto exit; + arr_port = kcalloc(port_nr, sizeof(void *), GFP_KERNEL); + if (!arr_port) + goto exit_free2; + + sha->sas_phy = arr_phy; + sha->sas_port = arr_port; + sha->lldd_ha = kzalloc(sizeof(struct pm8001_hba_info), GFP_KERNEL); + if (!sha->lldd_ha) + goto exit_free1; + + shost->transportt = pm8001_stt; + shost->max_id = PM8001_MAX_DEVICES; + shost->max_lun = 8; + shost->max_channel = 0; + shost->unique_id = pm8001_id; + shost->max_cmd_len = 16; + shost->can_queue = PM8001_CAN_QUEUE; + shost->cmd_per_lun = 32; + return 0; +exit_free1: + kfree(arr_port); +exit_free2: + kfree(arr_phy); +exit: + return -1; +} + +/** + * pm8001_post_sas_ha_init - initialize general hba struct defined in libsas + * @shost: scsi host which has been allocated outside + * @chip_info: our ha struct. + */ +static void __devinit pm8001_post_sas_ha_init(struct Scsi_Host *shost, + const struct pm8001_chip_info *chip_info) +{ + int i = 0; + struct pm8001_hba_info *pm8001_ha; + struct sas_ha_struct *sha = SHOST_TO_SAS_HA(shost); + + pm8001_ha = sha->lldd_ha; + for (i = 0; i < chip_info->n_phy; i++) { + sha->sas_phy[i] = &pm8001_ha->phy[i].sas_phy; + sha->sas_port[i] = &pm8001_ha->port[i].sas_port; + } + sha->sas_ha_name = DRV_NAME; + sha->dev = pm8001_ha->dev; + + sha->lldd_module = THIS_MODULE; + sha->sas_addr = &pm8001_ha->sas_addr[0]; + sha->num_phys = chip_info->n_phy; + sha->lldd_max_execute_num = 1; + sha->lldd_queue_size = PM8001_CAN_QUEUE; + sha->core.shost = shost; +} + +/** + * pm8001_init_sas_add - initialize sas address + * @chip_info: our ha struct. + * + * Currently we just set the fixed SAS address to our HBA,for manufacture, + * it should read from the EEPROM + */ +static void pm8001_init_sas_add(struct pm8001_hba_info *pm8001_ha) +{ + u8 i; +#ifdef PM8001_READ_VPD + DECLARE_COMPLETION_ONSTACK(completion); + struct pm8001_ioctl_payload payload; + pm8001_ha->nvmd_completion = &completion; + payload.minor_function = 0; + payload.length = 128; + payload.func_specific = kzalloc(128, GFP_KERNEL); + PM8001_CHIP_DISP->get_nvmd_req(pm8001_ha, &payload); + wait_for_completion(&completion); + for (i = 0; i < pm8001_ha->chip->n_phy; i++) { + memcpy(&pm8001_ha->phy[i].dev_sas_addr, pm8001_ha->sas_addr, + SAS_ADDR_SIZE); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("phy %d sas_addr = %016llx \n", i, + pm8001_ha->phy[i].dev_sas_addr)); + } +#else + for (i = 0; i < pm8001_ha->chip->n_phy; i++) { + pm8001_ha->phy[i].dev_sas_addr = 0x50010c600047f9d0ULL; + pm8001_ha->phy[i].dev_sas_addr = + cpu_to_be64((u64) + (*(u64 *)&pm8001_ha->phy[i].dev_sas_addr)); + } + memcpy(pm8001_ha->sas_addr, &pm8001_ha->phy[0].dev_sas_addr, + SAS_ADDR_SIZE); +#endif +} + +#ifdef PM8001_USE_MSIX +/** + * pm8001_setup_msix - enable MSI-X interrupt + * @chip_info: our ha struct. + * @irq_handler: irq_handler + */ +static u32 pm8001_setup_msix(struct pm8001_hba_info *pm8001_ha, + irq_handler_t irq_handler) +{ + u32 i = 0, j = 0; + u32 number_of_intr = 1; + int flag = 0; + u32 max_entry; + int rc; + max_entry = sizeof(pm8001_ha->msix_entries) / + sizeof(pm8001_ha->msix_entries[0]); + flag |= IRQF_DISABLED; + for (i = 0; i < max_entry ; i++) + pm8001_ha->msix_entries[i].entry = i; + rc = pci_enable_msix(pm8001_ha->pdev, pm8001_ha->msix_entries, + number_of_intr); + pm8001_ha->number_of_intr = number_of_intr; + if (!rc) { + for (i = 0; i < number_of_intr; i++) { + if (request_irq(pm8001_ha->msix_entries[i].vector, + irq_handler, flag, DRV_NAME, + SHOST_TO_SAS_HA(pm8001_ha->shost))) { + for (j = 0; j < i; j++) + free_irq( + pm8001_ha->msix_entries[j].vector, + SHOST_TO_SAS_HA(pm8001_ha->shost)); + pci_disable_msix(pm8001_ha->pdev); + break; + } + } + } + return rc; +} +#endif + +/** + * pm8001_request_irq - register interrupt + * @chip_info: our ha struct. + */ +static u32 pm8001_request_irq(struct pm8001_hba_info *pm8001_ha) +{ + struct pci_dev *pdev; + irq_handler_t irq_handler = pm8001_interrupt; + int rc; + + pdev = pm8001_ha->pdev; + +#ifdef PM8001_USE_MSIX + if (pci_find_capability(pdev, PCI_CAP_ID_MSIX)) + return pm8001_setup_msix(pm8001_ha, irq_handler); + else + goto intx; +#endif + +intx: + /* intialize the INT-X interrupt */ + rc = request_irq(pdev->irq, irq_handler, IRQF_SHARED, DRV_NAME, + SHOST_TO_SAS_HA(pm8001_ha->shost)); + return rc; +} + +/** + * pm8001_pci_probe - probe supported device + * @pdev: pci device which kernel has been prepared for. + * @ent: pci device id + * + * This function is the main initialization function, when register a new + * pci driver it is invoked, all struct an hardware initilization should be done + * here, also, register interrupt + */ +static int __devinit pm8001_pci_probe(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + unsigned int rc; + u32 pci_reg; + struct pm8001_hba_info *pm8001_ha; + struct Scsi_Host *shost = NULL; + const struct pm8001_chip_info *chip; + + dev_printk(KERN_INFO, &pdev->dev, + "pm8001: driver version %s\n", DRV_VERSION); + rc = pci_enable_device(pdev); + if (rc) + goto err_out_enable; + pci_set_master(pdev); + /* + * Enable pci slot busmaster by setting pci command register. + * This is required by FW for Cyclone card. + */ + + pci_read_config_dword(pdev, PCI_COMMAND, &pci_reg); + pci_reg |= 0x157; + pci_write_config_dword(pdev, PCI_COMMAND, pci_reg); + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) + goto err_out_disable; + rc = pci_go_44(pdev); + if (rc) + goto err_out_regions; + + shost = scsi_host_alloc(&pm8001_sht, sizeof(void *)); + if (!shost) { + rc = -ENOMEM; + goto err_out_regions; + } + chip = &pm8001_chips[ent->driver_data]; + SHOST_TO_SAS_HA(shost) = + kcalloc(1, sizeof(struct sas_ha_struct), GFP_KERNEL); + if (!SHOST_TO_SAS_HA(shost)) { + rc = -ENOMEM; + goto err_out_free_host; + } + + rc = pm8001_prep_sas_ha_init(shost, chip); + if (rc) { + rc = -ENOMEM; + goto err_out_free; + } + pci_set_drvdata(pdev, SHOST_TO_SAS_HA(shost)); + pm8001_ha = pm8001_pci_alloc(pdev, chip_8001, shost); + if (!pm8001_ha) { + rc = -ENOMEM; + goto err_out_free; + } + list_add_tail(&pm8001_ha->list, &hba_list); + PM8001_CHIP_DISP->chip_soft_rst(pm8001_ha, 0x252acbcd); + rc = PM8001_CHIP_DISP->chip_init(pm8001_ha); + if (rc) + goto err_out_ha_free; + + rc = scsi_add_host(shost, &pdev->dev); + if (rc) + goto err_out_ha_free; + rc = pm8001_request_irq(pm8001_ha); + if (rc) + goto err_out_shost; + + PM8001_CHIP_DISP->interrupt_enable(pm8001_ha); + pm8001_init_sas_add(pm8001_ha); + pm8001_post_sas_ha_init(shost, chip); + rc = sas_register_ha(SHOST_TO_SAS_HA(shost)); + if (rc) + goto err_out_shost; + scsi_scan_host(pm8001_ha->shost); + return 0; + +err_out_shost: + scsi_remove_host(pm8001_ha->shost); +err_out_ha_free: + pm8001_free(pm8001_ha); +err_out_free: + kfree(SHOST_TO_SAS_HA(shost)); +err_out_free_host: + kfree(shost); +err_out_regions: + pci_release_regions(pdev); +err_out_disable: + pci_disable_device(pdev); +err_out_enable: + return rc; +} + +static void __devexit pm8001_pci_remove(struct pci_dev *pdev) +{ + struct sas_ha_struct *sha = pci_get_drvdata(pdev); + struct pm8001_hba_info *pm8001_ha; + int i; + pm8001_ha = sha->lldd_ha; + pci_set_drvdata(pdev, NULL); + sas_unregister_ha(sha); + sas_remove_host(pm8001_ha->shost); + list_del(&pm8001_ha->list); + scsi_remove_host(pm8001_ha->shost); + PM8001_CHIP_DISP->interrupt_disable(pm8001_ha); + PM8001_CHIP_DISP->chip_soft_rst(pm8001_ha, 0x252acbcd); + +#ifdef PM8001_USE_MSIX + for (i = 0; i < pm8001_ha->number_of_intr; i++) + synchronize_irq(pm8001_ha->msix_entries[i].vector); + for (i = 0; i < pm8001_ha->number_of_intr; i++) + free_irq(pm8001_ha->msix_entries[i].vector, sha); + pci_disable_msix(pdev); +#else + free_irq(pm8001_ha->irq, sha); +#endif +#ifdef PM8001_USE_TASKLET + tasklet_kill(&pm8001_ha->tasklet); +#endif + pm8001_free(pm8001_ha); + kfree(sha->sas_phy); + kfree(sha->sas_port); + kfree(sha); + pci_release_regions(pdev); + pci_disable_device(pdev); +} + +/** + * pm8001_pci_suspend - power management suspend main entry point + * @pdev: PCI device struct + * @state: PM state change to (usually PCI_D3) + * + * Returns 0 success, anything else error. + */ +static int pm8001_pci_suspend(struct pci_dev *pdev, pm_message_t state) +{ + struct sas_ha_struct *sha = pci_get_drvdata(pdev); + struct pm8001_hba_info *pm8001_ha; + int i , pos; + u32 device_state; + pm8001_ha = sha->lldd_ha; + flush_scheduled_work(); + scsi_block_requests(pm8001_ha->shost); + pos = pci_find_capability(pdev, PCI_CAP_ID_PM); + if (pos == 0) { + printk(KERN_ERR " PCI PM not supported\n"); + return -ENODEV; + } + PM8001_CHIP_DISP->interrupt_disable(pm8001_ha); + PM8001_CHIP_DISP->chip_soft_rst(pm8001_ha, 0x252acbcd); +#ifdef PM8001_USE_MSIX + for (i = 0; i < pm8001_ha->number_of_intr; i++) + synchronize_irq(pm8001_ha->msix_entries[i].vector); + for (i = 0; i < pm8001_ha->number_of_intr; i++) + free_irq(pm8001_ha->msix_entries[i].vector, sha); + pci_disable_msix(pdev); +#else + free_irq(pm8001_ha->irq, sha); +#endif +#ifdef PM8001_USE_TASKLET + tasklet_kill(&pm8001_ha->tasklet); +#endif + device_state = pci_choose_state(pdev, state); + pm8001_printk("pdev=0x%p, slot=%s, entering " + "operating state [D%d]\n", pdev, + pm8001_ha->name, device_state); + pci_save_state(pdev); + pci_disable_device(pdev); + pci_set_power_state(pdev, device_state); + return 0; +} + +/** + * pm8001_pci_resume - power management resume main entry point + * @pdev: PCI device struct + * + * Returns 0 success, anything else error. + */ +static int pm8001_pci_resume(struct pci_dev *pdev) +{ + struct sas_ha_struct *sha = pci_get_drvdata(pdev); + struct pm8001_hba_info *pm8001_ha; + int rc; + u32 device_state; + pm8001_ha = sha->lldd_ha; + device_state = pdev->current_state; + + pm8001_printk("pdev=0x%p, slot=%s, resuming from previous " + "operating state [D%d]\n", pdev, pm8001_ha->name, device_state); + + pci_set_power_state(pdev, PCI_D0); + pci_enable_wake(pdev, PCI_D0, 0); + pci_restore_state(pdev); + rc = pci_enable_device(pdev); + if (rc) { + pm8001_printk("slot=%s Enable device failed during resume\n", + pm8001_ha->name); + goto err_out_enable; + } + + pci_set_master(pdev); + rc = pci_go_44(pdev); + if (rc) + goto err_out_disable; + + PM8001_CHIP_DISP->chip_soft_rst(pm8001_ha, 0x252acbcd); + rc = PM8001_CHIP_DISP->chip_init(pm8001_ha); + if (rc) + goto err_out_disable; + PM8001_CHIP_DISP->interrupt_disable(pm8001_ha); + rc = pm8001_request_irq(pm8001_ha); + if (rc) + goto err_out_disable; + #ifdef PM8001_USE_TASKLET + tasklet_init(&pm8001_ha->tasklet, pm8001_tasklet, + (unsigned long)pm8001_ha); + #endif + PM8001_CHIP_DISP->interrupt_enable(pm8001_ha); + scsi_unblock_requests(pm8001_ha->shost); + return 0; + +err_out_disable: + scsi_remove_host(pm8001_ha->shost); + pci_disable_device(pdev); +err_out_enable: + return rc; +} + +static struct pci_device_id __devinitdata pm8001_pci_table[] = { + { + PCI_VDEVICE(PMC_Sierra, 0x8001), chip_8001 + }, + { + PCI_DEVICE(0x117c, 0x0042), + .driver_data = chip_8001 + }, + {} /* terminate list */ +}; + +static struct pci_driver pm8001_pci_driver = { + .name = DRV_NAME, + .id_table = pm8001_pci_table, + .probe = pm8001_pci_probe, + .remove = __devexit_p(pm8001_pci_remove), + .suspend = pm8001_pci_suspend, + .resume = pm8001_pci_resume, +}; + +/** + * pm8001_init - initialize scsi transport template + */ +static int __init pm8001_init(void) +{ + int rc; + pm8001_id = 0; + pm8001_stt = sas_domain_attach_transport(&pm8001_transport_ops); + if (!pm8001_stt) + return -ENOMEM; + rc = pci_register_driver(&pm8001_pci_driver); + if (rc) + goto err_out; + return 0; +err_out: + sas_release_transport(pm8001_stt); + return rc; +} + +static void __exit pm8001_exit(void) +{ + pci_unregister_driver(&pm8001_pci_driver); + sas_release_transport(pm8001_stt); +} + +module_init(pm8001_init); +module_exit(pm8001_exit); + +MODULE_AUTHOR("Jack Wang <jack_wang@usish.com>"); +MODULE_DESCRIPTION("PMC-Sierra PM8001 SAS/SATA controller driver"); +MODULE_VERSION(DRV_VERSION); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, pm8001_pci_table); + |