diff options
Diffstat (limited to 'drivers/staging/dgnc/dgnc_neo.c')
| -rw-r--r-- | drivers/staging/dgnc/dgnc_neo.c | 1690 |
1 files changed, 0 insertions, 1690 deletions
diff --git a/drivers/staging/dgnc/dgnc_neo.c b/drivers/staging/dgnc/dgnc_neo.c deleted file mode 100644 index 0ae229c3aaaa..000000000000 --- a/drivers/staging/dgnc/dgnc_neo.c +++ /dev/null @@ -1,1690 +0,0 @@ -/* - * Copyright 2003 Digi International (www.digi.com) - * Scott H Kilau <Scott_Kilau at digi dot com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2, or (at your option) - * any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY, EXPRESS OR IMPLIED; without even the - * implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR - * PURPOSE. See the GNU General Public License for more details. - */ - -#include <linux/kernel.h> -#include <linux/sched.h> -#include <linux/interrupt.h> -#include <linux/delay.h> -#include <linux/io.h> -#include <linux/serial.h> -#include <linux/serial_reg.h> - -#include "dgnc_driver.h" -#include "dgnc_neo.h" -#include "dgnc_tty.h" - -static inline void neo_parse_lsr(struct dgnc_board *brd, uint port); -static inline void neo_parse_isr(struct dgnc_board *brd, uint port); -static void neo_copy_data_from_uart_to_queue(struct channel_t *ch); -static inline void neo_clear_break(struct channel_t *ch, int force); -static inline void neo_set_cts_flow_control(struct channel_t *ch); -static inline void neo_set_rts_flow_control(struct channel_t *ch); -static inline void neo_set_ixon_flow_control(struct channel_t *ch); -static inline void neo_set_ixoff_flow_control(struct channel_t *ch); -static inline void neo_set_no_output_flow_control(struct channel_t *ch); -static inline void neo_set_no_input_flow_control(struct channel_t *ch); -static inline void neo_set_new_start_stop_chars(struct channel_t *ch); -static void neo_parse_modem(struct channel_t *ch, unsigned char signals); -static void neo_tasklet(unsigned long data); -static void neo_vpd(struct dgnc_board *brd); -static void neo_uart_init(struct channel_t *ch); -static void neo_uart_off(struct channel_t *ch); -static int neo_drain(struct tty_struct *tty, uint seconds); -static void neo_param(struct tty_struct *tty); -static void neo_assert_modem_signals(struct channel_t *ch); -static void neo_flush_uart_write(struct channel_t *ch); -static void neo_flush_uart_read(struct channel_t *ch); -static void neo_disable_receiver(struct channel_t *ch); -static void neo_enable_receiver(struct channel_t *ch); -static void neo_send_break(struct channel_t *ch, int msecs); -static void neo_send_start_character(struct channel_t *ch); -static void neo_send_stop_character(struct channel_t *ch); -static void neo_copy_data_from_queue_to_uart(struct channel_t *ch); -static uint neo_get_uart_bytes_left(struct channel_t *ch); -static void neo_send_immediate_char(struct channel_t *ch, unsigned char c); -static irqreturn_t neo_intr(int irq, void *voidbrd); - -struct board_ops dgnc_neo_ops = { - .tasklet = neo_tasklet, - .intr = neo_intr, - .uart_init = neo_uart_init, - .uart_off = neo_uart_off, - .drain = neo_drain, - .param = neo_param, - .vpd = neo_vpd, - .assert_modem_signals = neo_assert_modem_signals, - .flush_uart_write = neo_flush_uart_write, - .flush_uart_read = neo_flush_uart_read, - .disable_receiver = neo_disable_receiver, - .enable_receiver = neo_enable_receiver, - .send_break = neo_send_break, - .send_start_character = neo_send_start_character, - .send_stop_character = neo_send_stop_character, - .copy_data_from_queue_to_uart = neo_copy_data_from_queue_to_uart, - .get_uart_bytes_left = neo_get_uart_bytes_left, - .send_immediate_char = neo_send_immediate_char -}; - -/* - * This function allows calls to ensure that all outstanding - * PCI writes have been completed, by doing a PCI read against - * a non-destructive, read-only location on the Neo card. - * - * In this case, we are reading the DVID (Read-only Device Identification) - * value of the Neo card. - */ -static inline void neo_pci_posting_flush(struct dgnc_board *bd) -{ - readb(bd->re_map_membase + 0x8D); -} - -static inline void neo_set_cts_flow_control(struct channel_t *ch) -{ - unsigned char ier = readb(&ch->ch_neo_uart->ier); - unsigned char efr = readb(&ch->ch_neo_uart->efr); - - /* Turn on auto CTS flow control */ - ier |= UART_17158_IER_CTSDSR; - efr |= (UART_17158_EFR_ECB | UART_17158_EFR_CTSDSR); - - /* Turn off auto Xon flow control */ - efr &= ~UART_17158_EFR_IXON; - - /* - * Why? Because Exar's spec says we have to zero it - * out before setting it - */ - writeb(0, &ch->ch_neo_uart->efr); - - /* Turn on UART enhanced bits */ - writeb(efr, &ch->ch_neo_uart->efr); - - /* Turn on table D, with 8 char hi/low watermarks */ - writeb(UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_4DELAY, - &ch->ch_neo_uart->fctr); - - /* Feed the UART our trigger levels */ - writeb(8, &ch->ch_neo_uart->tfifo); - ch->ch_t_tlevel = 8; - - writeb(ier, &ch->ch_neo_uart->ier); - - neo_pci_posting_flush(ch->ch_bd); -} - -static inline void neo_set_rts_flow_control(struct channel_t *ch) -{ - unsigned char ier = readb(&ch->ch_neo_uart->ier); - unsigned char efr = readb(&ch->ch_neo_uart->efr); - - /* Turn on auto RTS flow control */ - ier |= UART_17158_IER_RTSDTR; - efr |= (UART_17158_EFR_ECB | UART_17158_EFR_RTSDTR); - - /* Turn off auto Xoff flow control */ - ier &= ~UART_17158_IER_XOFF; - efr &= ~UART_17158_EFR_IXOFF; - - /* - * Why? Because Exar's spec says we have to zero it - * out before setting it - */ - writeb(0, &ch->ch_neo_uart->efr); - - /* Turn on UART enhanced bits */ - writeb(efr, &ch->ch_neo_uart->efr); - - writeb(UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_4DELAY, - &ch->ch_neo_uart->fctr); - ch->ch_r_watermark = 4; - - writeb(32, &ch->ch_neo_uart->rfifo); - ch->ch_r_tlevel = 32; - - writeb(ier, &ch->ch_neo_uart->ier); - - /* - * From the Neo UART spec sheet: - * The auto RTS/DTR function must be started by asserting - * RTS/DTR# output pin (MCR bit-0 or 1 to logic 1 after - * it is enabled. - */ - ch->ch_mostat |= UART_MCR_RTS; - - neo_pci_posting_flush(ch->ch_bd); -} - -static inline void neo_set_ixon_flow_control(struct channel_t *ch) -{ - unsigned char ier = readb(&ch->ch_neo_uart->ier); - unsigned char efr = readb(&ch->ch_neo_uart->efr); - - /* Turn off auto CTS flow control */ - ier &= ~UART_17158_IER_CTSDSR; - efr &= ~UART_17158_EFR_CTSDSR; - - /* Turn on auto Xon flow control */ - efr |= (UART_17158_EFR_ECB | UART_17158_EFR_IXON); - - /* - * Why? Because Exar's spec says we have to zero it - * out before setting it - */ - writeb(0, &ch->ch_neo_uart->efr); - - /* Turn on UART enhanced bits */ - writeb(efr, &ch->ch_neo_uart->efr); - - writeb(UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY, - &ch->ch_neo_uart->fctr); - ch->ch_r_watermark = 4; - - writeb(32, &ch->ch_neo_uart->rfifo); - ch->ch_r_tlevel = 32; - - /* Tell UART what start/stop chars it should be looking for */ - writeb(ch->ch_startc, &ch->ch_neo_uart->xonchar1); - writeb(0, &ch->ch_neo_uart->xonchar2); - - writeb(ch->ch_stopc, &ch->ch_neo_uart->xoffchar1); - writeb(0, &ch->ch_neo_uart->xoffchar2); - - writeb(ier, &ch->ch_neo_uart->ier); - - neo_pci_posting_flush(ch->ch_bd); -} - -static inline void neo_set_ixoff_flow_control(struct channel_t *ch) -{ - unsigned char ier = readb(&ch->ch_neo_uart->ier); - unsigned char efr = readb(&ch->ch_neo_uart->efr); - - /* Turn off auto RTS flow control */ - ier &= ~UART_17158_IER_RTSDTR; - efr &= ~UART_17158_EFR_RTSDTR; - - /* Turn on auto Xoff flow control */ - ier |= UART_17158_IER_XOFF; - efr |= (UART_17158_EFR_ECB | UART_17158_EFR_IXOFF); - - /* - * Why? Because Exar's spec says we have to zero it - * out before setting it - */ - writeb(0, &ch->ch_neo_uart->efr); - - /* Turn on UART enhanced bits */ - writeb(efr, &ch->ch_neo_uart->efr); - - /* Turn on table D, with 8 char hi/low watermarks */ - writeb(UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY, - &ch->ch_neo_uart->fctr); - - writeb(8, &ch->ch_neo_uart->tfifo); - ch->ch_t_tlevel = 8; - - /* Tell UART what start/stop chars it should be looking for */ - writeb(ch->ch_startc, &ch->ch_neo_uart->xonchar1); - writeb(0, &ch->ch_neo_uart->xonchar2); - - writeb(ch->ch_stopc, &ch->ch_neo_uart->xoffchar1); - writeb(0, &ch->ch_neo_uart->xoffchar2); - - writeb(ier, &ch->ch_neo_uart->ier); - - neo_pci_posting_flush(ch->ch_bd); -} - -static inline void neo_set_no_input_flow_control(struct channel_t *ch) -{ - unsigned char ier = readb(&ch->ch_neo_uart->ier); - unsigned char efr = readb(&ch->ch_neo_uart->efr); - - /* Turn off auto RTS flow control */ - ier &= ~UART_17158_IER_RTSDTR; - efr &= ~UART_17158_EFR_RTSDTR; - - /* Turn off auto Xoff flow control */ - ier &= ~UART_17158_IER_XOFF; - if (ch->ch_c_iflag & IXON) - efr &= ~(UART_17158_EFR_IXOFF); - else - efr &= ~(UART_17158_EFR_ECB | UART_17158_EFR_IXOFF); - - /* - * Why? Because Exar's spec says we have to zero - * it out before setting it - */ - writeb(0, &ch->ch_neo_uart->efr); - - /* Turn on UART enhanced bits */ - writeb(efr, &ch->ch_neo_uart->efr); - - /* Turn on table D, with 8 char hi/low watermarks */ - writeb(UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY, - &ch->ch_neo_uart->fctr); - - ch->ch_r_watermark = 0; - - writeb(16, &ch->ch_neo_uart->tfifo); - ch->ch_t_tlevel = 16; - - writeb(16, &ch->ch_neo_uart->rfifo); - ch->ch_r_tlevel = 16; - - writeb(ier, &ch->ch_neo_uart->ier); - - neo_pci_posting_flush(ch->ch_bd); -} - -static inline void neo_set_no_output_flow_control(struct channel_t *ch) -{ - unsigned char ier = readb(&ch->ch_neo_uart->ier); - unsigned char efr = readb(&ch->ch_neo_uart->efr); - - /* Turn off auto CTS flow control */ - ier &= ~UART_17158_IER_CTSDSR; - efr &= ~UART_17158_EFR_CTSDSR; - - /* Turn off auto Xon flow control */ - if (ch->ch_c_iflag & IXOFF) - efr &= ~UART_17158_EFR_IXON; - else - efr &= ~(UART_17158_EFR_ECB | UART_17158_EFR_IXON); - - /* - * Why? Because Exar's spec says we have to zero it - * out before setting it - */ - writeb(0, &ch->ch_neo_uart->efr); - - /* Turn on UART enhanced bits */ - writeb(efr, &ch->ch_neo_uart->efr); - - /* Turn on table D, with 8 char hi/low watermarks */ - writeb(UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY, - &ch->ch_neo_uart->fctr); - - ch->ch_r_watermark = 0; - - writeb(16, &ch->ch_neo_uart->tfifo); - ch->ch_t_tlevel = 16; - - writeb(16, &ch->ch_neo_uart->rfifo); - ch->ch_r_tlevel = 16; - - writeb(ier, &ch->ch_neo_uart->ier); - - neo_pci_posting_flush(ch->ch_bd); -} - -/* change UARTs start/stop chars */ -static inline void neo_set_new_start_stop_chars(struct channel_t *ch) -{ - /* if hardware flow control is set, then skip this whole thing */ - if (ch->ch_digi.digi_flags & (CTSPACE | RTSPACE) || - ch->ch_c_cflag & CRTSCTS) - return; - - /* Tell UART what start/stop chars it should be looking for */ - writeb(ch->ch_startc, &ch->ch_neo_uart->xonchar1); - writeb(0, &ch->ch_neo_uart->xonchar2); - - writeb(ch->ch_stopc, &ch->ch_neo_uart->xoffchar1); - writeb(0, &ch->ch_neo_uart->xoffchar2); - - neo_pci_posting_flush(ch->ch_bd); -} - -/* No locks are assumed to be held when calling this function. */ -static inline void neo_clear_break(struct channel_t *ch, int force) -{ - unsigned long flags; - - spin_lock_irqsave(&ch->ch_lock, flags); - - if (!ch->ch_stop_sending_break) { - spin_unlock_irqrestore(&ch->ch_lock, flags); - return; - } - - if (ch->ch_flags & CH_BREAK_SENDING) { - if (force || - time_after_eq(jiffies, ch->ch_stop_sending_break)) { - unsigned char temp = readb(&ch->ch_neo_uart->lcr); - - writeb((temp & ~UART_LCR_SBC), &ch->ch_neo_uart->lcr); - neo_pci_posting_flush(ch->ch_bd); - ch->ch_flags &= ~(CH_BREAK_SENDING); - ch->ch_stop_sending_break = 0; - } - } - spin_unlock_irqrestore(&ch->ch_lock, flags); -} - -/* Parse the ISR register. */ -static inline void neo_parse_isr(struct dgnc_board *brd, uint port) -{ - struct channel_t *ch; - unsigned char isr; - unsigned char cause; - unsigned long flags; - - ch = brd->channels[port]; - if (!ch) - return; - - /* Here we try to figure out what caused the interrupt to happen */ - while (1) { - isr = readb(&ch->ch_neo_uart->isr_fcr); - - if (isr & UART_IIR_NO_INT) - break; - - /* - * Yank off the upper 2 bits, - * which just show that the FIFO's are enabled. - */ - isr &= ~(UART_17158_IIR_FIFO_ENABLED); - - if (isr & (UART_17158_IIR_RDI_TIMEOUT | UART_IIR_RDI)) { - /* Read data from uart -> queue */ - neo_copy_data_from_uart_to_queue(ch); - /* - * Call our tty layer to enforce queue - * flow control if needed. - */ - spin_lock_irqsave(&ch->ch_lock, flags); - dgnc_check_queue_flow_control(ch); - spin_unlock_irqrestore(&ch->ch_lock, flags); - } - - if (isr & UART_IIR_THRI) { - spin_lock_irqsave(&ch->ch_lock, flags); - ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM); - spin_unlock_irqrestore(&ch->ch_lock, flags); - neo_copy_data_from_queue_to_uart(ch); - } - - if (isr & UART_17158_IIR_XONXOFF) { - cause = readb(&ch->ch_neo_uart->xoffchar1); - - /* - * Since the UART detected either an XON or - * XOFF match, we need to figure out which - * one it was, so we can suspend or resume data flow. - */ - if (cause == UART_17158_XON_DETECT) { - /* resume output if stopped */ - if (brd->channels[port]->ch_flags & CH_STOP) { - spin_lock_irqsave(&ch->ch_lock, - flags); - ch->ch_flags &= ~(CH_STOP); - spin_unlock_irqrestore(&ch->ch_lock, - flags); - } - } else if (cause == UART_17158_XOFF_DETECT) { - if (!(brd->channels[port]->ch_flags & - CH_STOP)) { - spin_lock_irqsave(&ch->ch_lock, - flags); - ch->ch_flags |= CH_STOP; - spin_unlock_irqrestore(&ch->ch_lock, - flags); - } - } - } - - if (isr & UART_17158_IIR_HWFLOW_STATE_CHANGE) { - /* - * If we get here, this means the hardware is - * doing auto flow control. Check to see whether - * RTS/DTR or CTS/DSR caused this interrupt. - */ - cause = readb(&ch->ch_neo_uart->mcr); - /* Which pin is doing auto flow? RTS or DTR? */ - if ((cause & 0x4) == 0) { - if (cause & UART_MCR_RTS) { - spin_lock_irqsave(&ch->ch_lock, - flags); - ch->ch_mostat |= UART_MCR_RTS; - spin_unlock_irqrestore(&ch->ch_lock, - flags); - } else { - spin_lock_irqsave(&ch->ch_lock, - flags); - ch->ch_mostat &= ~(UART_MCR_RTS); - spin_unlock_irqrestore(&ch->ch_lock, - flags); - } - } else { - if (cause & UART_MCR_DTR) { - spin_lock_irqsave(&ch->ch_lock, - flags); - ch->ch_mostat |= UART_MCR_DTR; - spin_unlock_irqrestore(&ch->ch_lock, - flags); - } else { - spin_lock_irqsave(&ch->ch_lock, - flags); - ch->ch_mostat &= ~(UART_MCR_DTR); - spin_unlock_irqrestore(&ch->ch_lock, - flags); - } - } - } - - neo_parse_modem(ch, readb(&ch->ch_neo_uart->msr)); - } -} - -static inline void neo_parse_lsr(struct dgnc_board *brd, uint port) -{ - struct channel_t *ch; - int linestatus; - unsigned long flags; - - if (!brd) - return; - - if (port >= brd->maxports) - return; - - ch = brd->channels[port]; - if (!ch) - return; - - linestatus = readb(&ch->ch_neo_uart->lsr); - - ch->ch_cached_lsr |= linestatus; - - if (ch->ch_cached_lsr & UART_LSR_DR) { - neo_copy_data_from_uart_to_queue(ch); - spin_lock_irqsave(&ch->ch_lock, flags); - dgnc_check_queue_flow_control(ch); - spin_unlock_irqrestore(&ch->ch_lock, flags); - } - - /* - * The next 3 tests should *NOT* happen, as the above test - * should encapsulate all 3... At least, thats what Exar says. - */ - - if (linestatus & UART_LSR_PE) - ch->ch_err_parity++; - - if (linestatus & UART_LSR_FE) - ch->ch_err_frame++; - - if (linestatus & UART_LSR_BI) - ch->ch_err_break++; - - if (linestatus & UART_LSR_OE) { - /* - * Rx Oruns. Exar says that an orun will NOT corrupt - * the FIFO. It will just replace the holding register - * with this new data byte. So basically just ignore this. - * Probably we should eventually have an orun stat in our - * driver... - */ - ch->ch_err_overrun++; - } - - if (linestatus & UART_LSR_THRE) { - spin_lock_irqsave(&ch->ch_lock, flags); - ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM); - spin_unlock_irqrestore(&ch->ch_lock, flags); - - neo_copy_data_from_queue_to_uart(ch); - } else if (linestatus & UART_17158_TX_AND_FIFO_CLR) { - spin_lock_irqsave(&ch->ch_lock, flags); - ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM); - spin_unlock_irqrestore(&ch->ch_lock, flags); - - neo_copy_data_from_queue_to_uart(ch); - } -} - -/* Send any/all changes to the line to the UART. */ -static void neo_param(struct tty_struct *tty) -{ - unsigned char lcr = 0; - unsigned char uart_lcr = 0; - unsigned char ier = 0; - unsigned char uart_ier = 0; - uint baud = 9600; - int quot = 0; - struct dgnc_board *bd; - struct channel_t *ch; - struct un_t *un; - - if (!tty) - return; - - un = (struct un_t *)tty->driver_data; - if (!un) - return; - - ch = un->un_ch; - if (!ch) - return; - - bd = ch->ch_bd; - if (!bd) - return; - - /* If baud rate is zero, flush queues, and set mval to drop DTR. */ - if ((ch->ch_c_cflag & (CBAUD)) == 0) { - ch->ch_r_head = 0; - ch->ch_r_tail = 0; - ch->ch_e_head = 0; - ch->ch_e_tail = 0; - ch->ch_w_head = 0; - ch->ch_w_tail = 0; - - neo_flush_uart_write(ch); - neo_flush_uart_read(ch); - - /* The baudrate is B0 so all modem lines are to be dropped. */ - ch->ch_flags |= (CH_BAUD0); - ch->ch_mostat &= ~(UART_MCR_RTS | UART_MCR_DTR); - neo_assert_modem_signals(ch); - ch->ch_old_baud = 0; - return; - - } else if (ch->ch_custom_speed) { - baud = ch->ch_custom_speed; - /* Handle transition from B0 */ - if (ch->ch_flags & CH_BAUD0) { - ch->ch_flags &= ~(CH_BAUD0); - - /* - * Bring back up RTS and DTR... - * Also handle RTS or DTR toggle if set. - */ - if (!(ch->ch_digi.digi_flags & DIGI_RTS_TOGGLE)) - ch->ch_mostat |= (UART_MCR_RTS); - if (!(ch->ch_digi.digi_flags & DIGI_DTR_TOGGLE)) - ch->ch_mostat |= (UART_MCR_DTR); - } - } else { - int iindex = 0; - int jindex = 0; - - ulong bauds[4][16] = { - { /* slowbaud */ - 0, 50, 75, 110, - 134, 150, 200, 300, - 600, 1200, 1800, 2400, - 4800, 9600, 19200, 38400 }, - { /* slowbaud & CBAUDEX */ - 0, 57600, 115200, 230400, - 460800, 150, 200, 921600, - 600, 1200, 1800, 2400, - 4800, 9600, 19200, 38400 }, - { /* fastbaud */ - 0, 57600, 76800, 115200, - 131657, 153600, 230400, 460800, - 921600, 1200, 1800, 2400, - 4800, 9600, 19200, 38400 }, - { /* fastbaud & CBAUDEX */ - 0, 57600, 115200, 230400, - 460800, 150, 200, 921600, - 600, 1200, 1800, 2400, - 4800, 9600, 19200, 38400 } - }; - - /* - * Only use the TXPrint baud rate if the terminal unit - * is NOT open - */ - if (!(ch->ch_tun.un_flags & UN_ISOPEN) && - (un->un_type == DGNC_PRINT)) - baud = C_BAUD(ch->ch_pun.un_tty) & 0xff; - else - baud = C_BAUD(ch->ch_tun.un_tty) & 0xff; - - if (ch->ch_c_cflag & CBAUDEX) - iindex = 1; - - if (ch->ch_digi.digi_flags & DIGI_FAST) - iindex += 2; - - jindex = baud; - - if ((iindex >= 0) && (iindex < 4) && - (jindex >= 0) && (jindex < 16)) - baud = bauds[iindex][jindex]; - else - baud = 0; - - if (baud == 0) - baud = 9600; - - /* Handle transition from B0 */ - if (ch->ch_flags & CH_BAUD0) { - ch->ch_flags &= ~(CH_BAUD0); - - /* - * Bring back up RTS and DTR... - * Also handle RTS or DTR toggle if set. - */ - if (!(ch->ch_digi.digi_flags & DIGI_RTS_TOGGLE)) - ch->ch_mostat |= (UART_MCR_RTS); - if (!(ch->ch_digi.digi_flags & DIGI_DTR_TOGGLE)) - ch->ch_mostat |= (UART_MCR_DTR); - } - } - - if (ch->ch_c_cflag & PARENB) - lcr |= UART_LCR_PARITY; - - if (!(ch->ch_c_cflag & PARODD)) - lcr |= UART_LCR_EPAR; - -#ifdef CMSPAR - if (ch->ch_c_cflag & CMSPAR) - lcr |= UART_LCR_SPAR; -#endif - - if (ch->ch_c_cflag & CSTOPB) - lcr |= UART_LCR_STOP; - - switch (ch->ch_c_cflag & CSIZE) { - case CS5: - lcr |= UART_LCR_WLEN5; - break; - case CS6: - lcr |= UART_LCR_WLEN6; - break; - case CS7: - lcr |= UART_LCR_WLEN7; - break; - case CS8: - default: - lcr |= UART_LCR_WLEN8; - break; - } - - uart_ier = readb(&ch->ch_neo_uart->ier); - ier = uart_ier; - - uart_lcr = readb(&ch->ch_neo_uart->lcr); - - if (baud == 0) - baud = 9600; - - quot = ch->ch_bd->bd_dividend / baud; - - if (quot != 0 && ch->ch_old_baud != baud) { - ch->ch_old_baud = baud; - writeb(UART_LCR_DLAB, &ch->ch_neo_uart->lcr); - writeb((quot & 0xff), &ch->ch_neo_uart->txrx); - writeb((quot >> 8), &ch->ch_neo_uart->ier); - writeb(lcr, &ch->ch_neo_uart->lcr); - } - - if (uart_lcr != lcr) - writeb(lcr, &ch->ch_neo_uart->lcr); - - if (ch->ch_c_cflag & CREAD) - ier |= (UART_IER_RDI | UART_IER_RLSI); - else - ier &= ~(UART_IER_RDI | UART_IER_RLSI); - - /* - * Have the UART interrupt on modem signal changes ONLY when - * we are in hardware flow control mode, or CLOCAL/FORCEDCD is not set. - */ - if ((ch->ch_digi.digi_flags & CTSPACE) || - (ch->ch_digi.digi_flags & RTSPACE) || - (ch->ch_c_cflag & CRTSCTS) || - !(ch->ch_digi.digi_flags & DIGI_FORCEDCD) || - !(ch->ch_c_cflag & CLOCAL)) - ier |= UART_IER_MSI; - else - ier &= ~UART_IER_MSI; - - ier |= UART_IER_THRI; - - if (ier != uart_ier) - writeb(ier, &ch->ch_neo_uart->ier); - - neo_set_new_start_stop_chars(ch); - - if (ch->ch_digi.digi_flags & CTSPACE || ch->ch_c_cflag & CRTSCTS) { - neo_set_cts_flow_control(ch); - } else if (ch->ch_c_iflag & IXON) { - if ((ch->ch_startc == _POSIX_VDISABLE) || - (ch->ch_stopc == _POSIX_VDISABLE)) - neo_set_no_output_flow_control(ch); - else - neo_set_ixon_flow_control(ch); - } else { - neo_set_no_output_flow_control(ch); - } - - if (ch->ch_digi.digi_flags & RTSPACE || ch->ch_c_cflag & CRTSCTS) { - neo_set_rts_flow_control(ch); - } else if (ch->ch_c_iflag & IXOFF) { - if ((ch->ch_startc == _POSIX_VDISABLE) || - (ch->ch_stopc == _POSIX_VDISABLE)) - neo_set_no_input_flow_control(ch); - else - neo_set_ixoff_flow_control(ch); - } else { - neo_set_no_input_flow_control(ch); - } - - /* - * Adjust the RX FIFO Trigger level if baud is less than 9600. - * Not exactly elegant, but this is needed because of the Exar chip's - * delay on firing off the RX FIFO interrupt on slower baud rates. - */ - if (baud < 9600) { - writeb(1, &ch->ch_neo_uart->rfifo); - ch->ch_r_tlevel = 1; - } - - neo_assert_modem_signals(ch); - - neo_parse_modem(ch, readb(&ch->ch_neo_uart->msr)); -} - -/* Board poller function. */ -static void neo_tasklet(unsigned long data) -{ - struct dgnc_board *bd = (struct dgnc_board *)data; - struct channel_t *ch; - unsigned long flags; - int i; - int state = 0; - int ports = 0; - - if (!bd) - return; - - spin_lock_irqsave(&bd->bd_lock, flags); - state = bd->state; - ports = bd->nasync; - spin_unlock_irqrestore(&bd->bd_lock, flags); - - /* - * Do NOT allow the interrupt routine to read the intr registers - * Until we release this lock. - */ - spin_lock_irqsave(&bd->bd_intr_lock, flags); - - if ((state == BOARD_READY) && (ports > 0)) { - for (i = 0; i < ports; i++) { - ch = bd->channels[i]; - if (!ch) - continue; - - /* - * NOTE: Remember you CANNOT hold any channel - * locks when calling the input routine. - * - * During input processing, its possible we - * will call the Linux ld, which might in turn, - * do a callback right back into us, resulting - * in us trying to grab the channel lock twice! - */ - dgnc_input(ch); - - /* - * Channel lock is grabbed and then released - * inside both of these routines, but neither - * call anything else that could call back into us. - */ - neo_copy_data_from_queue_to_uart(ch); - dgnc_wakeup_writes(ch); - - dgnc_carrier(ch); - - /* - * Check to see if we need to turn off a sending break. - * The timing check is done inside clear_break() - */ - if (ch->ch_stop_sending_break) - neo_clear_break(ch, 0); - } - } - - spin_unlock_irqrestore(&bd->bd_intr_lock, flags); -} - -/* Neo specific interrupt handler. */ -static irqreturn_t neo_intr(int irq, void *voidbrd) -{ - struct dgnc_board *brd = voidbrd; - struct channel_t *ch; - int port = 0; - int type; - u32 uart_poll; - unsigned long flags; - unsigned long flags2; - - if (!brd) - return IRQ_NONE; - - /* Lock out the slow poller from running on this board. */ - spin_lock_irqsave(&brd->bd_intr_lock, flags); - - /* - * Read in "extended" IRQ information from the 32bit Neo register. - * Bits 0-7: What port triggered the interrupt. - * Bits 8-31: Each 3bits indicate what type of interrupt occurred. - */ - uart_poll = readl(brd->re_map_membase + UART_17158_POLL_ADDR_OFFSET); - - /* - * If 0, no interrupts pending. - * This can happen if the IRQ is shared among a couple Neo/Classic - * boards. - */ - if (!uart_poll) { - spin_unlock_irqrestore(&brd->bd_intr_lock, flags); - return IRQ_NONE; - } - - while ((uart_poll & 0xff) != 0) { - type = uart_poll >> (8 + (port * 3)); - type &= 0x7; - - uart_poll &= ~(0x01 << port); - - switch (type) { - case UART_17158_RXRDY_TIMEOUT: - /* - * RXRDY Time-out is cleared by reading data in the - * RX FIFO until it falls below the trigger level. - */ - - if (port >= brd->nasync) - break; - - ch = brd->channels[port]; - neo_copy_data_from_uart_to_queue(ch); - - /* - * Call our tty layer to enforce queue flow control if - * needed. - */ - spin_lock_irqsave(&ch->ch_lock, flags2); - dgnc_check_queue_flow_control(ch); - spin_unlock_irqrestore(&ch->ch_lock, flags2); - - break; - - case UART_17158_RX_LINE_STATUS: - - /* RXRDY and RX LINE Status (logic OR of LSR[4:1]) */ - - neo_parse_lsr(brd, port); - break; - - case UART_17158_TXRDY: - /* - * TXRDY interrupt clears after reading ISR register - * for the UART channel. - */ - - /* - * Yes, this is odd... - * Why would I check EVERY possibility of type of - * interrupt, when we know its TXRDY??? - * Becuz for some reason, even tho we got triggered for - * TXRDY, it seems to be occasionally wrong. Instead of - * TX, which it should be, I was getting things like - * RXDY too. Weird. - */ - neo_parse_isr(brd, port); - break; - - case UART_17158_MSR: - /* MSR or flow control was seen. */ - neo_parse_isr(brd, port); - break; - - default: - break; - } - - port++; - } - - tasklet_schedule(&brd->helper_tasklet); - - spin_unlock_irqrestore(&brd->bd_intr_lock, flags); - - return IRQ_HANDLED; -} - -/* - * Neo specific way of turning off the receiver. - * Used as a way to enforce queue flow control when in - * hardware flow control mode. - */ -static void neo_disable_receiver(struct channel_t *ch) -{ - unsigned char tmp = readb(&ch->ch_neo_uart->ier); - - tmp &= ~(UART_IER_RDI); - writeb(tmp, &ch->ch_neo_uart->ier); - neo_pci_posting_flush(ch->ch_bd); -} - -/* - * Neo specific way of turning on the receiver. - * Used as a way to un-enforce queue flow control when in - * hardware flow control mode. - */ -static void neo_enable_receiver(struct channel_t *ch) -{ - unsigned char tmp = readb(&ch->ch_neo_uart->ier); - - tmp |= (UART_IER_RDI); - writeb(tmp, &ch->ch_neo_uart->ier); - neo_pci_posting_flush(ch->ch_bd); -} - -static void neo_copy_data_from_uart_to_queue(struct channel_t *ch) -{ - int qleft = 0; - unsigned char linestatus = 0; - unsigned char error_mask = 0; - int n = 0; - int total = 0; - ushort head; - ushort tail; - unsigned long flags; - - if (!ch) - return; - - spin_lock_irqsave(&ch->ch_lock, flags); - - head = ch->ch_r_head & RQUEUEMASK; - tail = ch->ch_r_tail & RQUEUEMASK; - - linestatus = ch->ch_cached_lsr; - ch->ch_cached_lsr = 0; - - qleft = tail - head - 1; - if (qleft < 0) - qleft += RQUEUEMASK + 1; - - if (!(ch->ch_flags & CH_FIFO_ENABLED)) { - /* force the FIFO copy to NOT be run */ - total = 0; - } else { - total = readb(&ch->ch_neo_uart->rfifo); - - /* - * EXAR chip bug - RX FIFO COUNT - Fudge factor. - * - * This resolves a problem/bug with the Exar chip that sometimes - * returns a bogus value in the rfifo register. - * The count can be any where from 0-3 bytes "off". - * Bizarre, but true. - */ - if ((ch->ch_bd->dvid & 0xf0) >= UART_XR17E158_DVID) - total -= 1; - else - total -= 3; - } - - total = min(total, qleft); - - while (total > 0) { - linestatus = readb(&ch->ch_neo_uart->lsr); - - if (linestatus & UART_17158_RX_FIFO_DATA_ERROR) - break; - - /* Make sure we don't go over the end of our queue */ - n = min(((uint)total), (RQUEUESIZE - (uint)head)); - - /* - * Cut down n even further if needed, this is to fix - * a problem with memcpy_fromio() with the Neo on the - * IBM pSeries platform. - * 15 bytes max appears to be the magic number. - */ - n = min_t(uint, n, 12); - - /* - * Since we are grabbing the linestatus register, which - * will reset some bits after our read, we need to ensure - * we don't miss our TX FIFO emptys. - */ - if (linestatus & (UART_LSR_THRE | UART_17158_TX_AND_FIFO_CLR)) - ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM); - - linestatus = 0; - - memcpy_fromio(ch->ch_rqueue + head, - &ch->ch_neo_uart->txrxburst, n); - - /* - * Since RX_FIFO_DATA_ERROR was 0, we are guaranteed - * that all the data currently in the FIFO is free of - * breaks and parity/frame/orun errors. - */ - memset(ch->ch_equeue + head, 0, n); - - head = (head + n) & RQUEUEMASK; - total -= n; - qleft -= n; - ch->ch_rxcount += n; - } - - /* - * Create a mask to determine whether we should - * insert the character (if any) into our queue. - */ - if (ch->ch_c_iflag & IGNBRK) - error_mask |= UART_LSR_BI; - - /* - * Now cleanup any leftover bytes still in the UART. - * Also deal with any possible queue overflow here as well. - */ - while (1) { - /* - * Its possible we have a linestatus from the loop above - * this, so we "OR" on any extra bits. - */ - linestatus |= readb(&ch->ch_neo_uart->lsr); - - /* - * If the chip tells us there is no more data pending to - * be read, we can then leave. - * But before we do, cache the linestatus, just in case. - */ - if (!(linestatus & UART_LSR_DR)) { - ch->ch_cached_lsr = linestatus; - break; - } - - /* No need to store this bit */ - linestatus &= ~UART_LSR_DR; - - /* - * Since we are grabbing the linestatus register, which - * will reset some bits after our read, we need to ensure - * we don't miss our TX FIFO emptys. - */ - if (linestatus & (UART_LSR_THRE | UART_17158_TX_AND_FIFO_CLR)) { - linestatus &= ~(UART_LSR_THRE | - UART_17158_TX_AND_FIFO_CLR); - ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM); - } - - if (linestatus & error_mask) { - unsigned char discard; - - linestatus = 0; - memcpy_fromio(&discard, &ch->ch_neo_uart->txrxburst, 1); - continue; - } - - /* - * If our queue is full, we have no choice but to drop - * some data. The assumption is that HWFLOW or SWFLOW - * should have stopped things way way before we got to - * this point. - */ - while (qleft < 1) { - tail = (tail + 1) & RQUEUEMASK; - ch->ch_r_tail = tail; - ch->ch_err_overrun++; - qleft++; - } - - memcpy_fromio(ch->ch_rqueue + head, - &ch->ch_neo_uart->txrxburst, 1); - ch->ch_equeue[head] = (unsigned char)linestatus; - - linestatus = 0; - - head = (head + 1) & RQUEUEMASK; - - qleft--; - ch->ch_rxcount++; - } - - ch->ch_r_head = head & RQUEUEMASK; - ch->ch_e_head = head & EQUEUEMASK; - - spin_unlock_irqrestore(&ch->ch_lock, flags); -} - -/* - * This function basically goes to sleep for secs, or until - * it gets signalled that the port has fully drained. - */ -static int neo_drain(struct tty_struct *tty, uint seconds) -{ - unsigned long flags; - struct channel_t *ch; - struct un_t *un; - - if (!tty) - return -ENXIO; - - un = (struct un_t *)tty->driver_data; - if (!un) - return -ENXIO; - - ch = un->un_ch; - if (!ch) - return -ENXIO; - - spin_lock_irqsave(&ch->ch_lock, flags); - un->un_flags |= UN_EMPTY; - spin_unlock_irqrestore(&ch->ch_lock, flags); - - /* If returned value is non-zero, user ctrl-c'ed us */ - return wait_event_interruptible_timeout(un->un_flags_wait, - ((un->un_flags & UN_EMPTY) == 0), - msecs_to_jiffies(seconds * 1000)); -} - -/* - * Flush the WRITE FIFO on the Neo. - * Channel lock MUST be held before calling this function! - */ -static void neo_flush_uart_write(struct channel_t *ch) -{ - unsigned char tmp = 0; - int i = 0; - - if (!ch) - return; - - writeb((UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_XMIT), - &ch->ch_neo_uart->isr_fcr); - neo_pci_posting_flush(ch->ch_bd); - - for (i = 0; i < 10; i++) { - /* - * Check to see if the UART completely flushed the FIFO - * FIFO. - */ - tmp = readb(&ch->ch_neo_uart->isr_fcr); - if (tmp & 4) - udelay(10); - else - break; - } - - ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM); -} - -/* - * Flush the READ FIFO on the Neo. - * Channel lock MUST be held before calling this function! - */ -static void neo_flush_uart_read(struct channel_t *ch) -{ - unsigned char tmp = 0; - int i = 0; - - if (!ch) - return; - - writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR, - &ch->ch_neo_uart->isr_fcr); - neo_pci_posting_flush(ch->ch_bd); - - for (i = 0; i < 10; i++) { - /* - * Check to see if the UART feels it completely flushed the - * FIFO. - */ - tmp = readb(&ch->ch_neo_uart->isr_fcr); - if (tmp & 2) - udelay(10); - else - break; - } -} - -static void neo_copy_data_from_queue_to_uart(struct channel_t *ch) -{ - ushort head; - ushort tail; - int n; - int s; - int qlen; - uint len_written = 0; - unsigned long flags; - - if (!ch) - return; - - spin_lock_irqsave(&ch->ch_lock, flags); - - if (ch->ch_w_tail == ch->ch_w_head) - goto exit_unlock; - - /* If port is "stopped", don't send any data to the UART */ - if ((ch->ch_flags & CH_FORCED_STOP) || - (ch->ch_flags & CH_BREAK_SENDING)) - goto exit_unlock; - - if (!(ch->ch_flags & CH_FIFO_ENABLED)) { - /* Send data directly to txrx register */ - unsigned char lsrbits = readb(&ch->ch_neo_uart->lsr); - - ch->ch_cached_lsr |= lsrbits; - if (ch->ch_cached_lsr & UART_LSR_THRE) { - ch->ch_cached_lsr &= ~(UART_LSR_THRE); - - /* - * If RTS Toggle mode is on, turn on RTS now if not - * already set, and make sure we get an event when the - * data transfer has completed. - */ - if (ch->ch_digi.digi_flags & DIGI_RTS_TOGGLE) { - if (!(ch->ch_mostat & UART_MCR_RTS)) { - ch->ch_mostat |= (UART_MCR_RTS); - neo_assert_modem_signals(ch); - } - ch->ch_tun.un_flags |= (UN_EMPTY); - } - /* - * If DTR Toggle mode is on, turn on DTR now if not - * already set, and make sure we get an event when the - * data transfer has completed. - */ - if (ch->ch_digi.digi_flags & DIGI_DTR_TOGGLE) { - if (!(ch->ch_mostat & UART_MCR_DTR)) { - ch->ch_mostat |= (UART_MCR_DTR); - neo_assert_modem_signals(ch); - } - ch->ch_tun.un_flags |= (UN_EMPTY); - } - - writeb(ch->ch_wqueue[ch->ch_w_tail], - &ch->ch_neo_uart->txrx); - ch->ch_w_tail++; - ch->ch_w_tail &= WQUEUEMASK; - ch->ch_txcount++; - } - - goto exit_unlock; - } - - /* We have to do it this way, because of the EXAR TXFIFO count bug. */ - - if ((ch->ch_bd->dvid & 0xf0) < UART_XR17E158_DVID) { - if (!(ch->ch_flags & (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM))) - goto exit_unlock; - - len_written = 0; - - n = readb(&ch->ch_neo_uart->tfifo); - - if ((unsigned int)n > ch->ch_t_tlevel) - goto exit_unlock; - - n = UART_17158_TX_FIFOSIZE - ch->ch_t_tlevel; - } else { - n = UART_17158_TX_FIFOSIZE - readb(&ch->ch_neo_uart->tfifo); - } - - head = ch->ch_w_head & WQUEUEMASK; - tail = ch->ch_w_tail & WQUEUEMASK; - qlen = (head - tail) & WQUEUEMASK; - - n = min(n, qlen); - - while (n > 0) { - s = ((head >= tail) ? head : WQUEUESIZE) - tail; - s = min(s, n); - - if (s <= 0) - break; - - /* - * If RTS Toggle mode is on, turn on RTS now if not already set, - * and make sure we get an event when the data transfer has - * completed. - */ - if (ch->ch_digi.digi_flags & DIGI_RTS_TOGGLE) { - if (!(ch->ch_mostat & UART_MCR_RTS)) { - ch->ch_mostat |= (UART_MCR_RTS); - neo_assert_modem_signals(ch); - } - ch->ch_tun.un_flags |= (UN_EMPTY); - } - - /* - * If DTR Toggle mode is on, turn on DTR now if not already set, - * and make sure we get an event when the data transfer has - * completed. - */ - if (ch->ch_digi.digi_flags & DIGI_DTR_TOGGLE) { - if (!(ch->ch_mostat & UART_MCR_DTR)) { - ch->ch_mostat |= (UART_MCR_DTR); - neo_assert_modem_signals(ch); - } - ch->ch_tun.un_flags |= (UN_EMPTY); - } - - memcpy_toio(&ch->ch_neo_uart->txrxburst, - ch->ch_wqueue + tail, s); - - tail = (tail + s) & WQUEUEMASK; - n -= s; - ch->ch_txcount += s; - len_written += s; - } - - ch->ch_w_tail = tail & WQUEUEMASK; - - if (len_written > 0) { - neo_pci_posting_flush(ch->ch_bd); - ch->ch_flags &= ~(CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM); - } - -exit_unlock: - spin_unlock_irqrestore(&ch->ch_lock, flags); -} - -static void neo_parse_modem(struct channel_t *ch, unsigned char signals) -{ - unsigned char msignals = signals; - - if (!ch) - return; - - /* - * Do altpin switching. Altpin switches DCD and DSR. - * This prolly breaks DSRPACE, so we should be more clever here. - */ - if (ch->ch_digi.digi_flags & DIGI_ALTPIN) { - unsigned char mswap = msignals; - - if (mswap & UART_MSR_DDCD) { - msignals &= ~UART_MSR_DDCD; - msignals |= UART_MSR_DDSR; - } - if (mswap & UART_MSR_DDSR) { - msignals &= ~UART_MSR_DDSR; - msignals |= UART_MSR_DDCD; - } - if (mswap & UART_MSR_DCD) { - msignals &= ~UART_MSR_DCD; - msignals |= UART_MSR_DSR; - } - if (mswap & UART_MSR_DSR) { - msignals &= ~UART_MSR_DSR; - msignals |= UART_MSR_DCD; - } - } - - /* Scrub off lower bits. They signify delta's */ - msignals &= 0xf0; - - if (msignals & UART_MSR_DCD) - ch->ch_mistat |= UART_MSR_DCD; - else - ch->ch_mistat &= ~UART_MSR_DCD; - - if (msignals & UART_MSR_DSR) - ch->ch_mistat |= UART_MSR_DSR; - else - ch->ch_mistat &= ~UART_MSR_DSR; - - if (msignals & UART_MSR_RI) - ch->ch_mistat |= UART_MSR_RI; - else - ch->ch_mistat &= ~UART_MSR_RI; - - if (msignals & UART_MSR_CTS) - ch->ch_mistat |= UART_MSR_CTS; - else - ch->ch_mistat &= ~UART_MSR_CTS; -} - -/* Make the UART raise any of the output signals we want up */ -static void neo_assert_modem_signals(struct channel_t *ch) -{ - unsigned char out; - - if (!ch) - return; - - out = ch->ch_mostat; - - if (ch->ch_flags & CH_LOOPBACK) - out |= UART_MCR_LOOP; - - writeb(out, &ch->ch_neo_uart->mcr); - neo_pci_posting_flush(ch->ch_bd); - - /* Give time for the UART to actually raise/drop the signals */ - udelay(10); -} - -static void neo_send_start_character(struct channel_t *ch) -{ - if (!ch) - return; - - if (ch->ch_startc != _POSIX_VDISABLE) { - ch->ch_xon_sends++; - writeb(ch->ch_startc, &ch->ch_neo_uart->txrx); - neo_pci_posting_flush(ch->ch_bd); - udelay(10); - } -} - -static void neo_send_stop_character(struct channel_t *ch) -{ - if (!ch) - return; - - if (ch->ch_stopc != _POSIX_VDISABLE) { - ch->ch_xoff_sends++; - writeb(ch->ch_stopc, &ch->ch_neo_uart->txrx); - neo_pci_posting_flush(ch->ch_bd); - udelay(10); - } -} - -/* neo_uart_init */ - -static void neo_uart_init(struct channel_t *ch) -{ - writeb(0, &ch->ch_neo_uart->ier); - writeb(0, &ch->ch_neo_uart->efr); - writeb(UART_EFR_ECB, &ch->ch_neo_uart->efr); - - /* Clear out UART and FIFO */ - readb(&ch->ch_neo_uart->txrx); - writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT, - &ch->ch_neo_uart->isr_fcr); - readb(&ch->ch_neo_uart->lsr); - readb(&ch->ch_neo_uart->msr); - - ch->ch_flags |= CH_FIFO_ENABLED; - - /* Assert any signals we want up */ - writeb(ch->ch_mostat, &ch->ch_neo_uart->mcr); - neo_pci_posting_flush(ch->ch_bd); -} - -/* Make the UART completely turn off. */ -static void neo_uart_off(struct channel_t *ch) -{ - /* Turn off UART enhanced bits */ - writeb(0, &ch->ch_neo_uart->efr); - - /* Stop all interrupts from occurring. */ - writeb(0, &ch->ch_neo_uart->ier); - neo_pci_posting_flush(ch->ch_bd); -} - -static uint neo_get_uart_bytes_left(struct channel_t *ch) -{ - unsigned char left = 0; - unsigned char lsr = readb(&ch->ch_neo_uart->lsr); - - /* We must cache the LSR as some of the bits get reset once read... */ - ch->ch_cached_lsr |= lsr; - - /* Determine whether the Transmitter is empty or not */ - if (!(lsr & UART_LSR_TEMT)) { - if (ch->ch_flags & CH_TX_FIFO_EMPTY) - tasklet_schedule(&ch->ch_bd->helper_tasklet); - left = 1; - } else { - ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM); - left = 0; - } - - return left; -} - -/* Channel lock MUST be held by the calling function! */ -static void neo_send_break(struct channel_t *ch, int msecs) -{ - /* If we receive a time of 0, this means turn off the break. */ - - if (msecs == 0) { - if (ch->ch_flags & CH_BREAK_SENDING) { - unsigned char temp = readb(&ch->ch_neo_uart->lcr); - - writeb((temp & ~UART_LCR_SBC), &ch->ch_neo_uart->lcr); - neo_pci_posting_flush(ch->ch_bd); - ch->ch_flags &= ~(CH_BREAK_SENDING); - ch->ch_stop_sending_break = 0; - } - return; - } - - /* - * Set the time we should stop sending the break. - * If we are already sending a break, toss away the existing - * time to stop, and use this new value instead. - */ - ch->ch_stop_sending_break = jiffies + dgnc_jiffies_from_ms(msecs); - - /* Tell the UART to start sending the break */ - if (!(ch->ch_flags & CH_BREAK_SENDING)) { - unsigned char temp = readb(&ch->ch_neo_uart->lcr); - - writeb((temp | UART_LCR_SBC), &ch->ch_neo_uart->lcr); - neo_pci_posting_flush(ch->ch_bd); - ch->ch_flags |= (CH_BREAK_SENDING); - } -} - -/* - * Sends a specific character as soon as possible to the UART, - * jumping over any bytes that might be in the write queue. - * - * The channel lock MUST be held by the calling function. - */ -static void neo_send_immediate_char(struct channel_t *ch, unsigned char c) -{ - if (!ch) - return; - - writeb(c, &ch->ch_neo_uart->txrx); - neo_pci_posting_flush(ch->ch_bd); -} - -static unsigned int neo_read_eeprom(unsigned char __iomem *base, - unsigned int address) -{ - unsigned int enable; - unsigned int bits; - unsigned int databit; - unsigned int val; - - /* enable chip select */ - writeb(NEO_EECS, base + NEO_EEREG); - /* READ */ - enable = address | 0x180; - - for (bits = 9; bits--; ) { - databit = (enable & (1 << bits)) ? NEO_EEDI : 0; - /* Set read address */ - writeb(databit | NEO_EECS, base + NEO_EEREG); - writeb(databit | NEO_EECS | NEO_EECK, base + NEO_EEREG); - } - - val = 0; - - for (bits = 17; bits--; ) { - /* clock to EEPROM */ - writeb(NEO_EECS, base + NEO_EEREG); - writeb(NEO_EECS | NEO_EECK, base + NEO_EEREG); - val <<= 1; - /* read EEPROM */ - if (readb(base + NEO_EEREG) & NEO_EEDO) - val |= 1; - } - - /* clock falling edge */ - writeb(NEO_EECS, base + NEO_EEREG); - - /* drop chip select */ - writeb(0x00, base + NEO_EEREG); - - return val; -} - -static void neo_vpd(struct dgnc_board *brd) -{ - unsigned int i = 0; - unsigned int a; - - if (!brd) - return; - - if (!brd->re_map_membase) - return; - - /* Store the VPD into our buffer */ - for (i = 0; i < NEO_VPD_IMAGESIZE; i++) { - a = neo_read_eeprom(brd->re_map_membase, i); - brd->vpd[i * 2] = a & 0xff; - brd->vpd[(i * 2) + 1] = (a >> 8) & 0xff; - } - - /* - * brd->vpd has different name tags by below index. - * 0x08 : long resource name tag - * 0x10 : long resource name tage (PCI-66 files) - * 0x7F : small resource end tag - */ - if (((brd->vpd[0x08] != 0x82) && - (brd->vpd[0x10] != 0x82)) || - (brd->vpd[0x7F] != 0x78)) { - memset(brd->vpd, '\0', NEO_VPD_IMAGESIZE); - } else { - /* Search for the serial number */ - for (i = 0; i < NEO_VPD_IMAGEBYTES - 3; i++) - if (brd->vpd[i] == 'S' && brd->vpd[i + 1] == 'N') - strncpy(brd->serial_num, &brd->vpd[i + 3], 9); - } -} |