1 files changed, 120 insertions, 0 deletions
diff --git a/drivers/staging/i2o/Kconfig b/drivers/staging/i2o/Kconfig
new file mode 100644
index 000000000000..286c53f4b13d
--- /dev/null
+++ b/drivers/staging/i2o/Kconfig
@@ -0,0 +1,120 @@
+menuconfig I2O
+	tristate "I2O device support"
+	depends on PCI
+	---help---
+	  The Intelligent Input/Output (I2O) architecture allows hardware
+	  drivers to be split into two parts: an operating system specific
+	  module called the OSM and an hardware specific module called the
+	  HDM. The OSM can talk to a whole range of HDM's, and ideally the
+	  HDM's are not OS dependent. This allows for the same HDM driver to
+	  be used under different operating systems if the relevant OSM is in
+	  place. In order for this to work, you need to have an I2O interface
+	  adapter card in your computer. This card contains a special I/O
+	  processor (IOP), thus allowing high speeds since the CPU does not
+	  have to deal with I/O.
+
+	  If you say Y here, you will get a choice of interface adapter
+	  drivers and OSM's with the following questions.
+
+	  To compile this support as a module, choose M here: the
+	  modules will be called i2o_core.
+
+	  If unsure, say N.
+
+if I2O
+
+config I2O_LCT_NOTIFY_ON_CHANGES
+	bool "Enable LCT notification"
+	default y
+	---help---
+	  Only say N here if you have a I2O controller from SUN. The SUN
+	  firmware doesn't support LCT notification on changes. If this option
+	  is enabled on such a controller the driver will hang up in a endless
+	  loop. On all other controllers say Y.
+
+	  If unsure, say Y.
+
+config I2O_EXT_ADAPTEC
+	bool "Enable Adaptec extensions"
+	default y
+	---help---
+	  Say Y for support of raidutils for Adaptec I2O controllers. You also
+	  have to say Y to "I2O Configuration support", "I2O SCSI OSM" below
+	  and to "SCSI generic support" under "SCSI device configuration".
+
+config I2O_EXT_ADAPTEC_DMA64
+	bool "Enable 64-bit DMA"
+	depends on I2O_EXT_ADAPTEC && ( 64BIT || HIGHMEM64G )
+	default y
+	---help---
+	  Say Y for support of 64-bit DMA transfer mode on Adaptec I2O
+	  controllers.
+	  Note: You need at least firmware version 3709.
+
+config I2O_CONFIG
+	tristate "I2O Configuration support"
+	depends on VIRT_TO_BUS
+	---help---
+	  Say Y for support of the configuration interface for the I2O adapters.
+	  If you have a RAID controller from Adaptec and you want to use the
+	  raidutils to manage your RAID array, you have to say Y here.
+
+	  To compile this support as a module, choose M here: the
+	  module will be called i2o_config.
+
+	  Note: If you want to use the new API you have to download the
+	  i2o_config patch from http://i2o.shadowconnect.com/
+
+config I2O_CONFIG_OLD_IOCTL
+	bool "Enable ioctls (OBSOLETE)"
+	depends on I2O_CONFIG
+	default y
+	---help---
+	  Enables old ioctls.
+
+config I2O_BUS
+	tristate "I2O Bus Adapter OSM"
+	---help---
+	  Include support for the I2O Bus Adapter OSM. The Bus Adapter OSM
+	  provides access to the busses on the I2O controller. The main purpose
+	  is to rescan the bus to find new devices.
+
+	  To compile this support as a module, choose M here: the
+	  module will be called i2o_bus.
+
+config I2O_BLOCK
+	tristate "I2O Block OSM"
+	depends on BLOCK
+	---help---
+	  Include support for the I2O Block OSM. The Block OSM presents disk
+	  and other structured block devices to the operating system. If you
+	  are using an RAID controller, you could access the array only by
+	  the Block OSM driver. But it is possible to access the single disks
+	  by the SCSI OSM driver, for example to monitor the disks.
+
+	  To compile this support as a module, choose M here: the
+	  module will be called i2o_block.
+
+config I2O_SCSI
+	tristate "I2O SCSI OSM"
+	depends on SCSI
+	---help---
+	  Allows direct SCSI access to SCSI devices on a SCSI or FibreChannel
+	  I2O controller. You can use both the SCSI and Block OSM together if
+	  you wish. To access a RAID array, you must use the Block OSM driver.
+	  But you could use the SCSI OSM driver to monitor the single disks.
+
+	  To compile this support as a module, choose M here: the
+	  module will be called i2o_scsi.
+
+config I2O_PROC
+	tristate "I2O /proc support"
+	---help---
+	  If you say Y here and to "/proc file system support", you will be
+	  able to read I2O related information from the virtual directory
+	  /proc/i2o.
+
+	  To compile this support as a module, choose M here: the
+	  module will be called i2o_proc.
+
+endif # I2O