diff options
Diffstat (limited to 'drivers/thermal/imx_thermal.c')
| -rw-r--r-- | drivers/thermal/imx_thermal.c | 53 |
1 files changed, 30 insertions, 23 deletions
diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c index 461bf3d033a0..c1188ac053c9 100644 --- a/drivers/thermal/imx_thermal.c +++ b/drivers/thermal/imx_thermal.c @@ -9,7 +9,6 @@ #include <linux/clk.h> #include <linux/cpu_cooling.h> -#include <linux/cpufreq.h> #include <linux/delay.h> #include <linux/device.h> #include <linux/init.h> @@ -454,7 +453,6 @@ static int imx_thermal_probe(struct platform_device *pdev) const struct of_device_id *of_id = of_match_device(of_imx_thermal_match, &pdev->dev); struct imx_thermal_data *data; - struct cpumask clip_cpus; struct regmap *map; int measure_freq; int ret; @@ -512,12 +510,37 @@ static int imx_thermal_probe(struct platform_device *pdev) regmap_write(map, MISC0 + REG_SET, MISC0_REFTOP_SELBIASOFF); regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN); - cpumask_set_cpu(0, &clip_cpus); - data->cdev = cpufreq_cooling_register(&clip_cpus); + data->cdev = cpufreq_cooling_register(cpu_present_mask); if (IS_ERR(data->cdev)) { ret = PTR_ERR(data->cdev); - dev_err(&pdev->dev, - "failed to register cpufreq cooling device: %d\n", ret); + if (ret != -EPROBE_DEFER) + dev_err(&pdev->dev, + "failed to register cpufreq cooling device: %d\n", + ret); + return ret; + } + + data->thermal_clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(data->thermal_clk)) { + ret = PTR_ERR(data->thermal_clk); + if (ret != -EPROBE_DEFER) + dev_err(&pdev->dev, + "failed to get thermal clk: %d\n", ret); + cpufreq_cooling_unregister(data->cdev); + return ret; + } + + /* + * Thermal sensor needs clk on to get correct value, normally + * we should enable its clk before taking measurement and disable + * clk after measurement is done, but if alarm function is enabled, + * hardware will auto measure the temperature periodically, so we + * need to keep the clk always on for alarm function. + */ + ret = clk_prepare_enable(data->thermal_clk); + if (ret) { + dev_err(&pdev->dev, "failed to enable thermal clk: %d\n", ret); + cpufreq_cooling_unregister(data->cdev); return ret; } @@ -531,26 +554,11 @@ static int imx_thermal_probe(struct platform_device *pdev) ret = PTR_ERR(data->tz); dev_err(&pdev->dev, "failed to register thermal zone device %d\n", ret); + clk_disable_unprepare(data->thermal_clk); cpufreq_cooling_unregister(data->cdev); return ret; } - data->thermal_clk = devm_clk_get(&pdev->dev, NULL); - if (IS_ERR(data->thermal_clk)) { - dev_warn(&pdev->dev, "failed to get thermal clk!\n"); - } else { - /* - * Thermal sensor needs clk on to get correct value, normally - * we should enable its clk before taking measurement and disable - * clk after measurement is done, but if alarm function is enabled, - * hardware will auto measure the temperature periodically, so we - * need to keep the clk always on for alarm function. - */ - ret = clk_prepare_enable(data->thermal_clk); - if (ret) - dev_warn(&pdev->dev, "failed to enable thermal clk: %d\n", ret); - } - /* Enable measurements at ~ 10 Hz */ regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ); measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */ @@ -624,7 +632,6 @@ static SIMPLE_DEV_PM_OPS(imx_thermal_pm_ops, static struct platform_driver imx_thermal = { .driver = { .name = "imx_thermal", - .owner = THIS_MODULE, .pm = &imx_thermal_pm_ops, .of_match_table = of_imx_thermal_match, }, |