aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/tty/serial/8250/8250_pci.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/tty/serial/8250/8250_pci.c')
-rw-r--r--drivers/tty/serial/8250/8250_pci.c164
1 files changed, 143 insertions, 21 deletions
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index e55f18b93fe7..68042dd1c525 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1417,6 +1417,10 @@ byt_set_termios(struct uart_port *p, struct ktermios *termios,
reg |= BYT_PRV_CLK_EN | BYT_PRV_CLK_UPDATE;
writel(reg, p->membase + BYT_PRV_CLK);
+ p->status &= ~UPSTAT_AUTOCTS;
+ if (termios->c_cflag & CRTSCTS)
+ p->status |= UPSTAT_AUTOCTS;
+
serial8250_do_set_termios(p, termios, old);
}
@@ -1685,11 +1689,65 @@ pci_brcm_trumanage_setup(struct serial_private *priv,
return ret;
}
+/* RTS will control by MCR if this bit is 0 */
+#define FINTEK_RTS_CONTROL_BY_HW BIT(4)
+/* only worked with FINTEK_RTS_CONTROL_BY_HW on */
+#define FINTEK_RTS_INVERT BIT(5)
+
+/* We should do proper H/W transceiver setting before change to RS485 mode */
+static int pci_fintek_rs485_config(struct uart_port *port,
+ struct serial_rs485 *rs485)
+{
+ u8 setting;
+ u8 *index = (u8 *) port->private_data;
+ struct pci_dev *pci_dev = container_of(port->dev, struct pci_dev,
+ dev);
+
+ pci_read_config_byte(pci_dev, 0x40 + 8 * *index + 7, &setting);
+
+ if (!rs485)
+ rs485 = &port->rs485;
+ else if (rs485->flags & SER_RS485_ENABLED)
+ memset(rs485->padding, 0, sizeof(rs485->padding));
+ else
+ memset(rs485, 0, sizeof(*rs485));
+
+ /* F81504/508/512 not support RTS delay before or after send */
+ rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND;
+
+ if (rs485->flags & SER_RS485_ENABLED) {
+ /* Enable RTS H/W control mode */
+ setting |= FINTEK_RTS_CONTROL_BY_HW;
+
+ if (rs485->flags & SER_RS485_RTS_ON_SEND) {
+ /* RTS driving high on TX */
+ setting &= ~FINTEK_RTS_INVERT;
+ } else {
+ /* RTS driving low on TX */
+ setting |= FINTEK_RTS_INVERT;
+ }
+
+ rs485->delay_rts_after_send = 0;
+ rs485->delay_rts_before_send = 0;
+ } else {
+ /* Disable RTS H/W control mode */
+ setting &= ~(FINTEK_RTS_CONTROL_BY_HW | FINTEK_RTS_INVERT);
+ }
+
+ pci_write_config_byte(pci_dev, 0x40 + 8 * *index + 7, setting);
+
+ if (rs485 != &port->rs485)
+ port->rs485 = *rs485;
+
+ return 0;
+}
+
static int pci_fintek_setup(struct serial_private *priv,
const struct pciserial_board *board,
struct uart_8250_port *port, int idx)
{
struct pci_dev *pdev = priv->dev;
+ u8 *data;
u8 config_base;
u16 iobase;
@@ -1702,6 +1760,15 @@ static int pci_fintek_setup(struct serial_private *priv,
port->port.iotype = UPIO_PORT;
port->port.iobase = iobase;
+ port->port.rs485_config = pci_fintek_rs485_config;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(u8), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ /* preserve index in PCI configuration space */
+ *data = idx;
+ port->port.private_data = data;
return 0;
}
@@ -1712,6 +1779,8 @@ static int pci_fintek_init(struct pci_dev *dev)
u32 max_port, i;
u32 bar_data[3];
u8 config_base;
+ struct serial_private *priv = pci_get_drvdata(dev);
+ struct uart_8250_port *port;
switch (dev->device) {
case 0x1104: /* 4 ports */
@@ -1752,6 +1821,19 @@ static int pci_fintek_init(struct pci_dev *dev)
(u8)((iobase & 0xff00) >> 8));
pci_write_config_byte(dev, config_base + 0x06, dev->irq);
+
+ if (priv) {
+ /* re-apply RS232/485 mode when
+ * pciserial_resume_ports()
+ */
+ port = serial8250_get_port(priv->line[i]);
+ pci_fintek_rs485_config(&port->port, NULL);
+ } else {
+ /* First init without port data
+ * force init to RS232 Mode
+ */
+ pci_write_config_byte(dev, config_base + 0x07, 0x01);
+ }
}
return max_port;
@@ -2017,6 +2099,12 @@ pci_wch_ch38x_setup(struct serial_private *priv,
#define PCIE_DEVICE_ID_WCH_CH382_2S1P 0x3250
#define PCIE_DEVICE_ID_WCH_CH384_4S 0x3470
+#define PCI_VENDOR_ID_PERICOM 0x12D8
+#define PCI_DEVICE_ID_PERICOM_PI7C9X7951 0x7951
+#define PCI_DEVICE_ID_PERICOM_PI7C9X7952 0x7952
+#define PCI_DEVICE_ID_PERICOM_PI7C9X7954 0x7954
+#define PCI_DEVICE_ID_PERICOM_PI7C9X7958 0x7958
+
/* Unknown vendors/cards - this should not be in linux/pci_ids.h */
#define PCI_SUBDEVICE_ID_UNKNOWN_0x1584 0x1584
#define PCI_SUBDEVICE_ID_UNKNOWN_0x1588 0x1588
@@ -2331,27 +2419,12 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
* Pericom
*/
{
- .vendor = 0x12d8,
- .device = 0x7952,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .setup = pci_pericom_setup,
- },
- {
- .vendor = 0x12d8,
- .device = 0x7954,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .setup = pci_pericom_setup,
- },
- {
- .vendor = 0x12d8,
- .device = 0x7958,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .setup = pci_pericom_setup,
+ .vendor = PCI_VENDOR_ID_PERICOM,
+ .device = PCI_ANY_ID,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_pericom_setup,
},
-
/*
* PLX
*/
@@ -3056,6 +3129,10 @@ enum pci_board_num_t {
pbn_fintek_8,
pbn_fintek_12,
pbn_wch384_4,
+ pbn_pericom_PI7C9X7951,
+ pbn_pericom_PI7C9X7952,
+ pbn_pericom_PI7C9X7954,
+ pbn_pericom_PI7C9X7958,
};
/*
@@ -3881,7 +3958,6 @@ static struct pciserial_board pci_boards[] = {
.base_baud = 115200,
.first_offset = 0x40,
},
-
[pbn_wch384_4] = {
.flags = FL_BASE0,
.num_ports = 4,
@@ -3889,6 +3965,33 @@ static struct pciserial_board pci_boards[] = {
.uart_offset = 8,
.first_offset = 0xC0,
},
+ /*
+ * Pericom PI7C9X795[1248] Uno/Dual/Quad/Octal UART
+ */
+ [pbn_pericom_PI7C9X7951] = {
+ .flags = FL_BASE0,
+ .num_ports = 1,
+ .base_baud = 921600,
+ .uart_offset = 0x8,
+ },
+ [pbn_pericom_PI7C9X7952] = {
+ .flags = FL_BASE0,
+ .num_ports = 2,
+ .base_baud = 921600,
+ .uart_offset = 0x8,
+ },
+ [pbn_pericom_PI7C9X7954] = {
+ .flags = FL_BASE0,
+ .num_ports = 4,
+ .base_baud = 921600,
+ .uart_offset = 0x8,
+ },
+ [pbn_pericom_PI7C9X7958] = {
+ .flags = FL_BASE0,
+ .num_ports = 8,
+ .base_baud = 921600,
+ .uart_offset = 0x8,
+ },
};
static const struct pci_device_id blacklist[] = {
@@ -5154,6 +5257,25 @@ static struct pci_device_id serial_pci_tbl[] = {
0,
0, pbn_exar_XR17V8358 },
/*
+ * Pericom PI7C9X795[1248] Uno/Dual/Quad/Octal UART
+ */
+ { PCI_VENDOR_ID_PERICOM, PCI_DEVICE_ID_PERICOM_PI7C9X7951,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_pericom_PI7C9X7951 },
+ { PCI_VENDOR_ID_PERICOM, PCI_DEVICE_ID_PERICOM_PI7C9X7952,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_pericom_PI7C9X7952 },
+ { PCI_VENDOR_ID_PERICOM, PCI_DEVICE_ID_PERICOM_PI7C9X7954,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_pericom_PI7C9X7954 },
+ { PCI_VENDOR_ID_PERICOM, PCI_DEVICE_ID_PERICOM_PI7C9X7958,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_pericom_PI7C9X7958 },
+ /*
* Topic TP560 Data/Fax/Voice 56k modem (reported by Evan Clarke)
*/
{ PCI_VENDOR_ID_TOPIC, PCI_DEVICE_ID_TOPIC_TP560,
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.