1 files changed, 22 insertions, 11 deletions

diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 09a65a3ec7f7..a5fe0e66c607 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -47,6 +47,7 @@
 /*
  * These are definitions for the Exar XR17V35X and XR17(C|D)15X
  */
+#define UART_EXAR_INT0		0x80
 #define UART_EXAR_SLEEP		0x8b	/* Sleep mode */
 #define UART_EXAR_DVID		0x8d	/* Device identification */
 
@@ -1337,7 +1338,7 @@ out_lock:
 	/*
 	 * Check if the device is a Fintek F81216A
 	 */
-	if (port->type == PORT_16550A)
+	if (port->type == PORT_16550A && port->iotype == UPIO_PORT)
 		fintek_8250_probe(up);
 
 	if (up->capabilities != old_capabilities) {
@@ -1763,6 +1764,10 @@ void serial8250_tx_chars(struct uart_8250_port *up)
 		if ((up->capabilities & UART_CAP_HFIFO) &&
 		    (serial_in(up, UART_LSR) & BOTH_EMPTY) != BOTH_EMPTY)
 			break;
+		/* The BCM2835 MINI UART THRE bit is really a not-full bit. */
+		if ((up->capabilities & UART_CAP_MINI) &&
+		    !(serial_in(up, UART_LSR) & UART_LSR_THRE))
+			break;
 	} while (--count > 0);
 
 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
@@ -1869,17 +1874,13 @@ static int serial8250_default_handle_irq(struct uart_port *port)
 static int exar_handle_irq(struct uart_port *port)
 {
 	unsigned int iir = serial_port_in(port, UART_IIR);
-	int ret;
+	int ret = 0;
 
-	ret = serial8250_handle_irq(port, iir);
+	if (((port->type == PORT_XR17V35X) || (port->type == PORT_XR17D15X)) &&
+	    serial_port_in(port, UART_EXAR_INT0) != 0)
+		ret = 1;
 
-	if ((port->type == PORT_XR17V35X) ||
-	   (port->type == PORT_XR17D15X)) {
-		serial_port_in(port, 0x80);
-		serial_port_in(port, 0x81);
-		serial_port_in(port, 0x82);
-		serial_port_in(port, 0x83);
-	}
+	ret |= serial8250_handle_irq(port, iir);
 
 	return ret;
 }
@@ -2177,6 +2178,8 @@ int serial8250_do_startup(struct uart_port *port)
 	serial_port_in(port, UART_RX);
 	serial_port_in(port, UART_IIR);
 	serial_port_in(port, UART_MSR);
+	if ((port->type == PORT_XR17V35X) || (port->type == PORT_XR17D15X))
+		serial_port_in(port, UART_EXAR_INT0);
 
 	/*
 	 * At this point, there's no way the LSR could still be 0xff;
@@ -2229,7 +2232,7 @@ int serial8250_do_startup(struct uart_port *port)
 		}
 	}
 
-	if (port->irq) {
+	if (port->irq && !(up->port.flags & UPF_NO_THRE_TEST)) {
 		unsigned char iir1;
 		/*
 		 * Test for UARTs that do not reassert THRE when the
@@ -2335,6 +2338,8 @@ dont_test_tx_en:
 	serial_port_in(port, UART_RX);
 	serial_port_in(port, UART_IIR);
 	serial_port_in(port, UART_MSR);
+	if ((port->type == PORT_XR17V35X) || (port->type == PORT_XR17D15X))
+		serial_port_in(port, UART_EXAR_INT0);
 	up->lsr_saved_flags = 0;
 	up->msr_saved_flags = 0;
 
@@ -2584,6 +2589,12 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
 	unsigned long flags;
 	unsigned int baud, quot, frac = 0;
 
+	if (up->capabilities & UART_CAP_MINI) {
+		termios->c_cflag &= ~(CSTOPB | PARENB | PARODD | CMSPAR);
+		if ((termios->c_cflag & CSIZE) == CS5 ||
+		    (termios->c_cflag & CSIZE) == CS6)
+			termios->c_cflag = (termios->c_cflag & ~CSIZE) | CS7;
+	}
 	cval = serial8250_compute_lcr(up, termios->c_cflag);
 
 	baud = serial8250_get_baud_rate(port, termios, old);