diff options
Diffstat (limited to 'drivers/tty/serial/fsl_lpuart.c')
| -rw-r--r-- | drivers/tty/serial/fsl_lpuart.c | 66 |
1 files changed, 8 insertions, 58 deletions
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c index be12fee94db5..0d6e62f6bb07 100644 --- a/drivers/tty/serial/fsl_lpuart.c +++ b/drivers/tty/serial/fsl_lpuart.c @@ -239,8 +239,6 @@ /* IMX lpuart has four extra unused regs located at the beginning */ #define IMX_REG_OFF 0x10 -static DEFINE_IDA(fsl_lpuart_ida); - enum lpuart_type { VF610_LPUART, LS1021A_LPUART, @@ -276,7 +274,6 @@ struct lpuart_port { int rx_dma_rng_buf_len; unsigned int dma_tx_nents; wait_queue_head_t dma_wait; - bool id_allocated; }; struct lpuart_soc_data { @@ -1118,7 +1115,7 @@ static void lpuart_copy_rx_to_tty(struct lpuart_port *sport) struct dma_chan *chan = sport->dma_rx_chan; struct circ_buf *ring = &sport->rx_ring; unsigned long flags; - int count = 0, copied; + int count, copied; if (lpuart_is_32(sport)) { unsigned long sr = lpuart32_read(&sport->port, UARTSTAT); @@ -1378,19 +1375,6 @@ static int lpuart_config_rs485(struct uart_port *port, modem |= UARTMODEM_TXRTSE; /* - * RTS needs to be logic HIGH either during transfer _or_ after - * transfer, other variants are not supported by the hardware. - */ - - if (!(rs485->flags & (SER_RS485_RTS_ON_SEND | - SER_RS485_RTS_AFTER_SEND))) - rs485->flags |= SER_RS485_RTS_ON_SEND; - - if (rs485->flags & SER_RS485_RTS_ON_SEND && - rs485->flags & SER_RS485_RTS_AFTER_SEND) - rs485->flags &= ~SER_RS485_RTS_AFTER_SEND; - - /* * The hardware defaults to RTS logic HIGH while transfer. * Switch polarity in case RTS shall be logic HIGH * after transfer. @@ -1402,9 +1386,6 @@ static int lpuart_config_rs485(struct uart_port *port, modem |= UARTMODEM_TXRTSPOL; } - /* Store the new configuration */ - sport->port.rs485 = *rs485; - writeb(modem, sport->port.membase + UARTMODEM); return 0; } @@ -1429,19 +1410,6 @@ static int lpuart32_config_rs485(struct uart_port *port, modem |= UARTMODEM_TXRTSE; /* - * RTS needs to be logic HIGH either during transfer _or_ after - * transfer, other variants are not supported by the hardware. - */ - - if (!(rs485->flags & (SER_RS485_RTS_ON_SEND | - SER_RS485_RTS_AFTER_SEND))) - rs485->flags |= SER_RS485_RTS_ON_SEND; - - if (rs485->flags & SER_RS485_RTS_ON_SEND && - rs485->flags & SER_RS485_RTS_AFTER_SEND) - rs485->flags &= ~SER_RS485_RTS_AFTER_SEND; - - /* * The hardware defaults to RTS logic HIGH while transfer. * Switch polarity in case RTS shall be logic HIGH * after transfer. @@ -1453,9 +1421,6 @@ static int lpuart32_config_rs485(struct uart_port *port, modem |= UARTMODEM_TXRTSPOL; } - /* Store the new configuration */ - sport->port.rs485 = *rs485; - lpuart32_write(&sport->port, modem, UARTMODIR); return 0; } @@ -2145,12 +2110,10 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios, if (sport->port.rs485.flags & SER_RS485_ENABLED) termios->c_cflag &= ~CRTSCTS; - if (termios->c_cflag & CRTSCTS) { - modem |= (UARTMODIR_RXRTSE | UARTMODIR_TXCTSE); - } else { - termios->c_cflag &= ~CRTSCTS; + if (termios->c_cflag & CRTSCTS) + modem |= UARTMODIR_RXRTSE | UARTMODIR_TXCTSE; + else modem &= ~(UARTMODIR_RXRTSE | UARTMODIR_TXCTSE); - } if (termios->c_cflag & CSTOPB) bd |= UARTBAUD_SBNS; @@ -2717,23 +2680,18 @@ static int lpuart_probe(struct platform_device *pdev) ret = of_alias_get_id(np, "serial"); if (ret < 0) { - ret = ida_simple_get(&fsl_lpuart_ida, 0, UART_NR, GFP_KERNEL); - if (ret < 0) { - dev_err(&pdev->dev, "port line is full, add device failed\n"); - return ret; - } - sport->id_allocated = true; + dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret); + return ret; } if (ret >= ARRAY_SIZE(lpuart_ports)) { dev_err(&pdev->dev, "serial%d out of range\n", ret); - ret = -EINVAL; - goto failed_out_of_range; + return -EINVAL; } sport->port.line = ret; ret = lpuart_enable_clks(sport); if (ret) - goto failed_clock_enable; + return ret; sport->port.uartclk = lpuart_get_baud_clk_rate(sport); lpuart_ports[sport->port.line] = sport; @@ -2781,10 +2739,6 @@ failed_reset: uart_remove_one_port(&lpuart_reg, &sport->port); failed_attach_port: lpuart_disable_clks(sport); -failed_clock_enable: -failed_out_of_range: - if (sport->id_allocated) - ida_simple_remove(&fsl_lpuart_ida, sport->port.line); return ret; } @@ -2794,9 +2748,6 @@ static int lpuart_remove(struct platform_device *pdev) uart_remove_one_port(&lpuart_reg, &sport->port); - if (sport->id_allocated) - ida_simple_remove(&fsl_lpuart_ida, sport->port.line); - lpuart_disable_clks(sport); if (sport->dma_tx_chan) @@ -2926,7 +2877,6 @@ static int __init lpuart_serial_init(void) static void __exit lpuart_serial_exit(void) { - ida_destroy(&fsl_lpuart_ida); platform_driver_unregister(&lpuart_driver); uart_unregister_driver(&lpuart_reg); } |