diff options
Diffstat (limited to 'include/asm-arm/arch-clps711x/hardware.h')
| -rw-r--r-- | include/asm-arm/arch-clps711x/hardware.h | 237 |
1 files changed, 0 insertions, 237 deletions
diff --git a/include/asm-arm/arch-clps711x/hardware.h b/include/asm-arm/arch-clps711x/hardware.h deleted file mode 100644 index 0fdbe72fff2a..000000000000 --- a/include/asm-arm/arch-clps711x/hardware.h +++ /dev/null @@ -1,237 +0,0 @@ -/* - * linux/include/asm-arm/arch-clps711x/hardware.h - * - * This file contains the hardware definitions of the Prospector P720T. - * - * Copyright (C) 2000 Deep Blue Solutions Ltd. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -#ifndef __ASM_ARCH_HARDWARE_H -#define __ASM_ARCH_HARDWARE_H - - -#define CLPS7111_VIRT_BASE 0xff000000 -#define CLPS7111_BASE CLPS7111_VIRT_BASE - -/* - * The physical addresses that the external chip select signals map to is - * dependent on the setting of the nMEDCHG signal on EP7211 and EP7212 - * processors. CONFIG_EP72XX_BOOT_ROM is only available if these - * processors are in use. - */ -#ifndef CONFIG_EP72XX_ROM_BOOT -#define CS0_PHYS_BASE (0x00000000) -#define CS1_PHYS_BASE (0x10000000) -#define CS2_PHYS_BASE (0x20000000) -#define CS3_PHYS_BASE (0x30000000) -#define CS4_PHYS_BASE (0x40000000) -#define CS5_PHYS_BASE (0x50000000) -#define CS6_PHYS_BASE (0x60000000) -#define CS7_PHYS_BASE (0x70000000) -#else -#define CS0_PHYS_BASE (0x70000000) -#define CS1_PHYS_BASE (0x60000000) -#define CS2_PHYS_BASE (0x50000000) -#define CS3_PHYS_BASE (0x40000000) -#define CS4_PHYS_BASE (0x30000000) -#define CS5_PHYS_BASE (0x20000000) -#define CS6_PHYS_BASE (0x10000000) -#define CS7_PHYS_BASE (0x00000000) -#endif - -#if defined (CONFIG_ARCH_EP7211) - -#define EP7211_VIRT_BASE CLPS7111_VIRT_BASE -#define EP7211_BASE CLPS7111_VIRT_BASE -#include <asm/hardware/ep7211.h> - -#elif defined (CONFIG_ARCH_EP7212) - -#define EP7212_VIRT_BASE CLPS7111_VIRT_BASE -#define EP7212_BASE CLPS7111_VIRT_BASE -#include <asm/hardware/ep7212.h> - -#endif - -#define SYSPLD_VIRT_BASE 0xfe000000 -#define SYSPLD_BASE SYSPLD_VIRT_BASE - -#ifndef __ASSEMBLER__ - -#define PCIO_BASE IO_BASE - -#endif - - -#if defined (CONFIG_ARCH_AUTCPU12) - -#define CS89712_VIRT_BASE CLPS7111_VIRT_BASE -#define CS89712_BASE CLPS7111_VIRT_BASE - -#include <asm/hardware/clps7111.h> -#include <asm/hardware/ep7212.h> -#include <asm/hardware/cs89712.h> - -#endif - - -#if defined (CONFIG_ARCH_CDB89712) - -#include <asm/hardware/clps7111.h> -#include <asm/hardware/ep7212.h> -#include <asm/hardware/cs89712.h> - -/* dynamic ioremap() areas */ -#define FLASH_START 0x00000000 -#define FLASH_SIZE 0x800000 -#define FLASH_WIDTH 4 - -#define SRAM_START 0x60000000 -#define SRAM_SIZE 0xc000 -#define SRAM_WIDTH 4 - -#define BOOTROM_START 0x70000000 -#define BOOTROM_SIZE 0x80 -#define BOOTROM_WIDTH 4 - - -/* static cdb89712_map_io() areas */ -#define REGISTER_START 0x80000000 -#define REGISTER_SIZE 0x4000 -#define REGISTER_BASE 0xff000000 - -#define ETHER_START 0x20000000 -#define ETHER_SIZE 0x1000 -#define ETHER_BASE 0xfe000000 - -#endif - - -#if defined (CONFIG_ARCH_EDB7211) - -/* - * The extra 8 lines of the keyboard matrix are wired to chip select 3 (nCS3) - * and repeat across it. This is the mapping for it. - * - * In jumpered boot mode, nCS3 is mapped to 0x4000000, not 0x3000000. This - * was cause for much consternation and headscratching. This should probably - * be made a compile/run time kernel option. - */ -#define EP7211_PHYS_EXTKBD CS3_PHYS_BASE /* physical */ - -#define EP7211_VIRT_EXTKBD (0xfd000000) /* virtual */ - - -/* - * The CS8900A ethernet chip has its I/O registers wired to chip select 2 - * (nCS2). This is the mapping for it. - * - * In jumpered boot mode, nCS2 is mapped to 0x5000000, not 0x2000000. This - * was cause for much consternation and headscratching. This should probably - * be made a compile/run time kernel option. - */ -#define EP7211_PHYS_CS8900A CS2_PHYS_BASE /* physical */ - -#define EP7211_VIRT_CS8900A (0xfc000000) /* virtual */ - - -/* - * The two flash banks are wired to chip selects 0 and 1. This is the mapping - * for them. - * - * nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running - * in jumpered boot mode. - */ -#define EP7211_PHYS_FLASH1 CS0_PHYS_BASE /* physical */ -#define EP7211_PHYS_FLASH2 CS1_PHYS_BASE /* physical */ - -#define EP7211_VIRT_FLASH1 (0xfa000000) /* virtual */ -#define EP7211_VIRT_FLASH2 (0xfb000000) /* virtual */ - -#endif /* CONFIG_ARCH_EDB7211 */ - - -/* - * Relevant bits in port D, which controls power to the various parts of - * the LCD on the EDB7211. - */ -#define EDB_PD1_LCD_DC_DC_EN (1<<1) -#define EDB_PD2_LCDEN (1<<2) -#define EDB_PD3_LCDBL (1<<3) - - -#if defined (CONFIG_ARCH_CEIVA) - -#define CEIVA_VIRT_BASE CLPS7111_VIRT_BASE -#define CEIVA_BASE CLPS7111_VIRT_BASE - -#include <asm/hardware/clps7111.h> -#include <asm/hardware/ep7212.h> - - -/* - * The two flash banks are wired to chip selects 0 and 1. This is the mapping - * for them. - * - * nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running - * in jumpered boot mode. - */ -#define CEIVA_PHYS_FLASH1 CS0_PHYS_BASE /* physical */ -#define CEIVA_PHYS_FLASH2 CS1_PHYS_BASE /* physical */ - -#define CEIVA_VIRT_FLASH1 (0xfa000000) /* virtual */ -#define CEIVA_VIRT_FLASH2 (0xfb000000) /* virtual */ - -#define CEIVA_FLASH_SIZE 0x100000 -#define CEIVA_FLASH_WIDTH 2 - -#define SRAM_START 0x60000000 -#define SRAM_SIZE 0xc000 -#define SRAM_WIDTH 4 - -#define BOOTROM_START 0x70000000 -#define BOOTROM_SIZE 0x80 -#define BOOTROM_WIDTH 4 - -/* - * SED1355 LCD controller - */ -#define CEIVA_PHYS_SED1355 CS2_PHYS_BASE -#define CEIVA_VIRT_SED1355 (0xfc000000) - -/* - * Relevant bits in port D, which controls power to the various parts of - * the LCD on the Ceiva Photo Max, and reset to the LCD controller. - */ - -// Reset line to SED1355 (must be high to operate) -#define CEIVA_PD1_LCDRST (1<<1) -// LCD panel enable (set to one, to enable LCD) -#define CEIVA_PD4_LCDEN (1<<4) -// Backlight (set to one, to turn on backlight -#define CEIVA_PD5_LCDBL (1<<5) - -/* - * Relevant bits in port B, which report the status of the buttons. - */ - -// White button -#define CEIVA_PB4_WHT_BTN (1<<4) -// Black button -#define CEIVA_PB0_BLK_BTN (1<<0) -#endif // #if defined (CONFIG_ARCH_CEIVA) - -#endif |