diff options
Diffstat (limited to '')
| -rwxr-xr-x | tools/testing/selftests/drivers/net/mlxsw/qos_max_descriptors.sh | 282 |
1 files changed, 282 insertions, 0 deletions
diff --git a/tools/testing/selftests/drivers/net/mlxsw/qos_max_descriptors.sh b/tools/testing/selftests/drivers/net/mlxsw/qos_max_descriptors.sh new file mode 100755 index 000000000000..5ac4f795e333 --- /dev/null +++ b/tools/testing/selftests/drivers/net/mlxsw/qos_max_descriptors.sh @@ -0,0 +1,282 @@ +#!/bin/bash +# SPDX-License-Identifier: GPL-2.0 +# +# This test sends many small packets (size is less than cell size) through the +# switch. A shaper is used in $swp2, so the traffic is limited there. Packets +# are queued till they will be sent. +# +# The idea is to verify that the switch can handle at least 85% of maximum +# supported descrpitors by hardware. Then, we verify that the driver configures +# firmware to allow infinite size of egress descriptor pool, and does not use a +# lower limitation. Increase the size of the relevant pools such that the pool's +# size does not limit the traffic. + +# +-----------------------+ +# | H1 | +# | + $h1.111 | +# | | 192.0.2.33/28 | +# | | | +# | + $h1 | +# +---|-------------------+ +# | +# +---|-----------------------------+ +# | + $swp1 | +# | | iPOOL1 | +# | | | +# | +-|------------------------+ | +# | | + $swp1.111 | | +# | | | | +# | | BR1 | | +# | | | | +# | | + $swp2.111 | | +# | +-|------------------------+ | +# | | | +# | + $swp2 | +# | | ePOOL6 | +# | | 1mbit | +# +---+-----------------------------+ +# | +# +---|-------------------+ +# | + $h2 H2 | +# | | | +# | + $h2.111 | +# | 192.0.2.34/28 | +# +-----------------------+ +# + +ALL_TESTS=" + ping_ipv4 + max_descriptors +" + +lib_dir=$(dirname $0)/../../../net/forwarding + +NUM_NETIFS=4 +source $lib_dir/lib.sh +source $lib_dir/devlink_lib.sh +source mlxsw_lib.sh + +MAX_POOL_SIZE=$(devlink_pool_size_get) +SHAPER_RATE=1mbit + +# The current TBF qdisc interface does not allow us to configure the shaper to +# flat zero. The ASIC shaper is guaranteed to work with a granularity of +# 200Mbps. On Spectrum-2, writing a value close to zero instead of zero works +# well, but the performance on Spectrum-1 is unpredictable. Thus, do not run the +# test on Spectrum-1. +mlxsw_only_on_spectrum 2+ || exit + +h1_create() +{ + simple_if_init $h1 + + vlan_create $h1 111 v$h1 192.0.2.33/28 + ip link set dev $h1.111 type vlan egress-qos-map 0:1 +} + +h1_destroy() +{ + vlan_destroy $h1 111 + + simple_if_fini $h1 +} + +h2_create() +{ + simple_if_init $h2 + + vlan_create $h2 111 v$h2 192.0.2.34/28 +} + +h2_destroy() +{ + vlan_destroy $h2 111 + + simple_if_fini $h2 +} + +switch_create() +{ + # pools + # ----- + + devlink_pool_size_thtype_save 1 + devlink_pool_size_thtype_save 6 + + devlink_port_pool_th_save $swp1 1 + devlink_port_pool_th_save $swp2 6 + + devlink_tc_bind_pool_th_save $swp1 1 ingress + devlink_tc_bind_pool_th_save $swp2 1 egress + + devlink_pool_size_thtype_set 1 dynamic $MAX_POOL_SIZE + devlink_pool_size_thtype_set 6 static $MAX_POOL_SIZE + + # $swp1 + # ----- + + ip link set dev $swp1 up + vlan_create $swp1 111 + ip link set dev $swp1.111 type vlan ingress-qos-map 0:0 1:1 + + devlink_port_pool_th_set $swp1 1 16 + devlink_tc_bind_pool_th_set $swp1 1 ingress 1 16 + + tc qdisc replace dev $swp1 root handle 1: \ + ets bands 8 strict 8 priomap 7 6 + dcb buffer set dev $swp1 prio-buffer all:0 1:1 + + # $swp2 + # ----- + + ip link set dev $swp2 up + vlan_create $swp2 111 + ip link set dev $swp2.111 type vlan egress-qos-map 0:0 1:1 + + devlink_port_pool_th_set $swp2 6 $MAX_POOL_SIZE + devlink_tc_bind_pool_th_set $swp2 1 egress 6 $MAX_POOL_SIZE + + tc qdisc replace dev $swp2 root handle 1: tbf rate $SHAPER_RATE \ + burst 128K limit 500M + tc qdisc replace dev $swp2 parent 1:1 handle 11: \ + ets bands 8 strict 8 priomap 7 6 + + # bridge + # ------ + + ip link add name br1 type bridge vlan_filtering 0 + ip link set dev $swp1.111 master br1 + ip link set dev br1 up + + ip link set dev $swp2.111 master br1 +} + +switch_destroy() +{ + # Do this first so that we can reset the limits to values that are only + # valid for the original static / dynamic setting. + devlink_pool_size_thtype_restore 6 + devlink_pool_size_thtype_restore 1 + + # bridge + # ------ + + ip link set dev $swp2.111 nomaster + + ip link set dev br1 down + ip link set dev $swp1.111 nomaster + ip link del dev br1 + + # $swp2 + # ----- + + tc qdisc del dev $swp2 parent 1:1 handle 11: + tc qdisc del dev $swp2 root + + devlink_tc_bind_pool_th_restore $swp2 1 egress + devlink_port_pool_th_restore $swp2 6 + + vlan_destroy $swp2 111 + ip link set dev $swp2 down + + # $swp1 + # ----- + + dcb buffer set dev $swp1 prio-buffer all:0 + tc qdisc del dev $swp1 root + + devlink_tc_bind_pool_th_restore $swp1 1 ingress + devlink_port_pool_th_restore $swp1 1 + + vlan_destroy $swp1 111 + ip link set dev $swp1 down +} + +setup_prepare() +{ + h1=${NETIFS[p1]} + swp1=${NETIFS[p2]} + + swp2=${NETIFS[p3]} + h2=${NETIFS[p4]} + + h2mac=$(mac_get $h2) + + vrf_prepare + + h1_create + h2_create + switch_create +} + +cleanup() +{ + pre_cleanup + + switch_destroy + h2_destroy + h1_destroy + + vrf_cleanup +} + +ping_ipv4() +{ + ping_test $h1 192.0.2.34 " h1->h2" +} + +percentage_used() +{ + local num_packets=$1; shift + local max_packets=$1; shift + + bc <<< " + scale=2 + 100 * $num_packets / $max_packets + " +} + +max_descriptors() +{ + local cell_size=$(devlink_cell_size_get) + local exp_perc_used=85 + local max_descriptors + local pktsize=30 + + RET=0 + + max_descriptors=$(mlxsw_max_descriptors_get) || exit 1 + + local d0=$(ethtool_stats_get $swp2 tc_no_buffer_discard_uc_tc_1) + + log_info "Send many small packets, packet size = $pktsize bytes" + start_traffic_pktsize $pktsize $h1.111 192.0.2.33 192.0.2.34 $h2mac + + # Sleep to wait for congestion. + sleep 5 + + local d1=$(ethtool_stats_get $swp2 tc_no_buffer_discard_uc_tc_1) + ((d1 == d0)) + check_err $? "Drops seen on egress port: $d0 -> $d1 ($((d1 - d0)))" + + # Check how many packets the switch can handle, the limitation is + # maximum descriptors. + local pkts_bytes=$(ethtool_stats_get $swp2 tc_transmit_queue_tc_1) + local pkts_num=$((pkts_bytes / cell_size)) + local perc_used=$(percentage_used $pkts_num $max_descriptors) + + check_err $(bc <<< "$perc_used < $exp_perc_used") \ + "Expected > $exp_perc_used% of descriptors, handle $perc_used%" + + stop_traffic + sleep 1 + + log_test "Maximum descriptors usage. The percentage used is $perc_used%" +} + +trap cleanup EXIT +setup_prepare +setup_wait +tests_run + +exit $EXIT_STATUS |