| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay") intended to
set coalescing threshold to a value guaranteeing interrupt generation
per each sent packet, so that buffers can be released with no delay.
In fact setting threshold to '1' was wrong, because it causes interrupt
every two packets. According to the documentation a reason behind it is
following - interrupt occurs once sent buffers counter reaches a value,
which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This
behavior was confirmed during tests. Also when testing the SoC working
as a NAS device, better performance was observed with int-per-packet,
as it strongly depends on the fact that all transmitted packets are
released immediately.
This commit enables NETA controller work in interrupt per sent packet mode
by setting coalescing threshold to 0.
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v3.10+
Fixes aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay")
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was first reported and reproduced by Petr (thanks!) in
https://bugzilla.kernel.org/show_bug.cgi?id=119581
free_percpu(rt->rt6i_pcpu) used to always happen in ip6_dst_destroy().
However, after fixing a deadlock bug in
commit 9c7370a166b4 ("ipv6: Fix a potential deadlock when creating pcpu rt"),
free_percpu() is not called before setting non_pcpu_rt->rt6i_pcpu to NULL.
It is worth to note that rt6i_pcpu is protected by table->tb6_lock.
kmemleak somehow did not report it. We nailed it down by
observing the pcpu entries in /proc/vmallocinfo (first suggested
by Hannes, thanks!).
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Fixes: 9c7370a166b4 ("ipv6: Fix a potential deadlock when creating pcpu rt")
Reported-by: Petr Novopashenniy <pety@rusnet.ru>
Tested-by: Petr Novopashenniy <pety@rusnet.ru>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Petr Novopashenniy <pety@rusnet.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dn_fib_count_nhs() could enter an infinite loop if nhp->rtnh_len == 0
(i.e. if userspace passes a malformed netlink message).
Let's use the helpers from net/nexthop.h which take care of all this
stuff. We can do exactly the same as e.g. fib_count_nexthops() and
fib_get_nhs() from net/ipv4/fib_semantics.c.
This fixes the softlockup for me.
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We verify "u_cmd.outsize" and "u_cmd.insize" but we need to make sure
that those values have not changed between the two copy_from_user()
calls. Otherwise it could lead to a buffer overflow.
Additionally, cros_ec_cmd_xfer() can set s_cmd->insize to a lower value.
We should use the new smaller value so we don't copy too much data to
the user.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com>
Fixes: a841178445bb ('mfd: cros_ec: Use a zero-length array for command data')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Change t4fw_version.h to update latest firmware version number
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GCC complains on unused-but-set-variable, clean this up.
Fixes: 23898c763f4a ('net/mlx5: E-Switch, Modify node guid on vf set MAC')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, link notifications are not sent by
bond_set_slave_link_state() upon enslavement if
the slave is enslaved when up.
This happens because slave->link default init value
is 0, which is the same as BOND_LINK_UP, resulting
in bond_set_slave_link_state() ignoring this transition.
This patch sets the default value of slave->link to
BOND_LINK_NOCHANGE, assuring it will count as a state
transition and thus trigger notification logic.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RTL8152 doesn't have U1U2 and U2P3 features, so use different
runtime functions for RTL812 and RTL8153 by adding autosuspend_en()
to rtl_ops.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This solves the issue that a headphone is not working on the docking
unit.
Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A qeth_card contains a napi_struct linked to the net_device during
device probing. This struct must be deleted when removing the qeth
device, otherwise Panic on oops can occur when qeth devices are
repeatedly removed and added.
Fixes: a1c3ed4c9ca ("qeth: NAPI support for l2 and l3 discipline")
Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Tested-by: Alexander Klein <ALKL@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit a788a4a040e003574b8ad17115706ab1601ec572.
This patch is wrong, the type returned doesn't fit
what the error pointer macros expect.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is likely that checking 'fman->fifo_offset' instead of
'fman->cam_offset' is expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several Lenovo users have reported problems with their Sierra
Wireless EM7455 modem. The driver has loaded successfully and
the MBIM management channel has appeared to work, including
establishing a connection to the mobile network. But no frames
have been received over the data interface.
The problem affects all EM7455 and MC7455, and is assumed to
affect other modems based on the same Qualcomm chipset and
baseband firmware.
Testing narrowed the problem down to what seems to be a
firmware timing bug during initialization. Adding a short sleep
while probing is sufficient to make the problem disappear.
Experiments have shown that 1-2 ms is too little to have any
effect, while 10-20 ms is enough to reliably succeed.
Reported-by: Stefan Armbruster <ml001@armbruster-it.de>
Reported-by: Ralph Plawetzki <ralph@purejava.org>
Reported-by: Andreas Fett <andreas.fett@secunet.com>
Reported-by: Rasmus Lerdorf <rasmus@lerdorf.com>
Reported-by: Samo Ratnik <samo.ratnik@gmail.com>
Reported-and-tested-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If register_pernet_subsys() fails, we shouldn't try to call
unregister_pernet_subsys().
Fixes: 467fa15356 ("RDS-TCP: Support multiple RDS-TCP listen endpoints, one per netns.")
Cc: stable@vger.kernel.org
Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For ipv6+udp+geneve encapsulation data, the max_mtu should subtract
sizeof(ipv6hdr), instead of sizeof(iphdr).
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The user timer tu->qused counter may go to a negative value when
multiple concurrent reads are performed since both the check and the
decrement of tu->qused are done in two individual locked contexts.
This results in bogus read outs, and the endless loop in the
user-space side.
The fix is to move the decrement of the tu->qused counter into the
same spinlock context as the zero-check of the counter.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
overlay needs underlying fs to support d_type. Recently I put in a
patch in to detect this condition and started failing mount if
underlying fs did not support d_type.
But this breaks existing configurations over kernel upgrade. Those who
are running docker (partially broken configuration) with xfs not
supporting d_type, are surprised that after kernel upgrade docker does
not run anymore.
https://github.com/docker/docker/issues/22937#issuecomment-229881315
So instead of erroring out, detect broken configuration and warn
about it. This should allow existing docker setups to continue
working after kernel upgrade.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 45aebeaf4f67 ("ovl: Ensure upper filesystem supports d_type")
Cc: <stable@vger.kernel.org> 4.6
|
|
When initializing the PHY control register, the FIFO depth bits are
written without reading the previous register value, i.e. all other
bits are overwritten with zero. This disables automatic MDI-X
configuration, which is enabled by default. Fix initialization by doing
a read/modify/write operation.
Signed-off-by: Stefan Hauser <stefan@shauser.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interrupt worker code for the enc28j60 relies only on the TXIF flag to
determinate if the packet transmission was completed. However the datasheet
specifies in section 12.1.3 that TXERIF will clear the TXRTS after a
transmit abort. Also in section 12.1.4 that TXIF will be set
when TXRTS transitions from '1' to '0'. Therefore the TXIF flag is enabled
during transmission errors.
This causes a race condition, since the worker code will invoke
enc28j60_tx_clear() -> netif_wake_queue(), potentially invoking the
ndo_start_xmit function to send a new packet. The enc28j60_send_packet function
uses a workqueue that invokes enc28j60_hw_tx(). In between this function is
called, the worker from the interrupt handler will enter the path for error
handler because of the TXERIF flag, causing to invoke enc28j60_tx_clear() again
and releasing the packet scheduled for transmission, causing a kernel crash with
due a NULL pointer.
These crashes due a NULL pointer were observed under stress conditions of the
device. A BUG_ON() sequence was used to validate the issue was fixed, and has
been running without problems for 2 years now.
Signed-off-by: Diego Dompe <dompe@hpe.com>
Acked-by: Sergio Valverde <sergio.valverde@hpe.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(resent due to overhelpful mail client corrupting patch)
At least on Meson GXBB, the CORE_IRQ_MTL_RX_OVERFLOW interrupt is thrown
with the stmmac1000 driver, which does not support set_rx_tail_ptr. With
this patch and the clock fixes, 1G ethernet works on ODROID-C2.
Signed-off-by: Matt Corallo <git@bluematt.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following testcase may result in a page table entries with a invalid
CCA field being generated:
static void *bindstack;
static int sysrqfd;
static void protect_low(int protect)
{
mprotect(bindstack, BINDSTACK_SIZE, protect);
}
static void sigbus_handler(int signal, siginfo_t * info, void *context)
{
void *addr = info->si_addr;
write(sysrqfd, "x", 1);
printf("sigbus, fault address %p (should not happen, but might)\n",
addr);
abort();
}
static void run_bind_test(void)
{
unsigned int *p = bindstack;
p[0] = 0xf001f001;
write(sysrqfd, "x", 1);
/* Set trap on access to p[0] */
protect_low(PROT_NONE);
write(sysrqfd, "x", 1);
/* Clear trap on access to p[0] */
protect_low(PROT_READ | PROT_WRITE | PROT_EXEC);
write(sysrqfd, "x", 1);
/* Check the contents of p[0] */
if (p[0] != 0xf001f001) {
write(sysrqfd, "x", 1);
/* Reached, but shouldn't be */
printf("badness, shouldn't happen but does\n");
abort();
}
}
int main(void)
{
struct sigaction sa;
sysrqfd = open("/proc/sysrq-trigger", O_WRONLY);
if (sigprocmask(SIG_BLOCK, NULL, &sa.sa_mask)) {
perror("sigprocmask");
return 0;
}
sa.sa_sigaction = sigbus_handler;
sa.sa_flags = SA_SIGINFO | SA_NODEFER | SA_RESTART;
if (sigaction(SIGBUS, &sa, NULL)) {
perror("sigaction");
return 0;
}
bindstack = mmap(NULL,
BINDSTACK_SIZE,
PROT_READ | PROT_WRITE | PROT_EXEC,
MAP_PRIVATE | MAP_ANONYMOUS, -1, 0);
if (bindstack == MAP_FAILED) {
perror("mmap bindstack");
return 0;
}
printf("bindstack: %p\n", bindstack);
run_bind_test();
printf("done\n");
return 0;
}
There are multiple ingredients for this:
1) PAGE_NONE is defined to _CACHE_CACHABLE_NONCOHERENT, which is CCA 3
on all platforms except SB1 where it's CCA 5.
2) _page_cachable_default must have bits set which are not set
_CACHE_CACHABLE_NONCOHERENT.
3) Either the defective version of pte_modify for XPA or the standard
version must be in used. However pte_modify for the 36 bit address
space support is no affected.
In that case additional bits in the final CCA mode may generate an invalid
value for the CCA field. On the R10000 system where this was tracked
down for example a CCA 7 has been observed, which is Uncached Accelerated.
Fixed by:
1) Using the proper CCA mode for PAGE_NONE just like for all the other
PAGE_* pte/pmd bits.
2) Fix the two affected variants of pte_modify.
Further code inspection also shows the same issue to exist in pmd_modify
which would affect huge page systems.
Issue in pte_modify tracked down by Alastair Bridgewater, PAGE_NONE
and pmd_modify issue found by me.
The history of this goes back beyond Linus' git history. Chris Dearman's
commit 351336929ccf222ae38ff0cb7a8dd5fd5c6236a0 ("[MIPS] Allow setting of
the cache attribute at run time.") missed the opportunity to fix this
but it was originally introduced in lmo commit
d523832cf12007b3242e50bb77d0c9e63e0b6518 ("Missing from last commit.")
and 32cc38229ac7538f2346918a09e75413e8861f87 ("New configuration option
CONFIG_MIPS_UNCACHED.")
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
|
|
Fix incorrect use of nla_strlcpy() where the first NLA_HDRLEN bytes
of the link name where left out.
Making the output of tipc-config -ls look something like:
Link statistics:
dcast-link
1:data0-1.1.2:data0
1:data0-1.1.3:data0
Also, for the record, the patch that introduce this regression
claims "Sending the whole object out can cause a leak". Which isn't
very likely as this is a compat layer, where the data we are parsing
is generated by us and we know the string to be NULL terminated. But
you can of course never be to secure.
Fixes: 5d2be1422e02 (tipc: fix an infoleak in tipc_nl_compat_link_dump)
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 64bits kernels, device stats are 64bits wide, not 32bits.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid recursions of dev_queue_xmit() to the wrong net device when
frames are unprotected, since at that time skb->dev still points to
our own macsec dev and unlike macsec_encrypt_finish() dev pointer
doesn't get updated to real underlying device.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to commit 9b368814b336 ("net: fix bridge multicast packet checksum validation")
we need to fixup the checksum for CHECKSUM_COMPLETE when
pushing skb on RX path. Otherwise we get similar splats.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
People who use PACKET_FANOUT_HASH want a symmetric hash, meaning that
they want packets going in both directions on a flow to hash to the
same bucket.
The core kernel SKB hash became non-symmetric when the ipv6 flow label
and other entities were incorporated into the standard flow hash order
to increase entropy.
But there are no users of PACKET_FANOUT_HASH who want an assymetric
hash, they all want a symmetric one.
Therefore, use the flow dissector to compute a flat symmetric hash
over only the protocol, addresses and ports. This hash does not get
installed into and override the normal skb hash, so this change has
no effect whatsoever on the rest of the stack.
Reported-by: Eric Leblond <eric@regit.org>
Tested-by: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(Another one for the f_path debacle.)
ltp fcntl33 testcase caused an Oops in selinux_file_send_sigiotask.
The reason is that generic_add_lease() used filp->f_path.dentry->inode
while all the others use file_inode(). This makes a difference for files
opened on overlayfs since the former will point to the overlay inode the
latter to the underlying inode.
So generic_add_lease() added the lease to the overlay inode and
generic_delete_lease() removed it from the underlying inode. When the file
was released the lease remained on the overlay inode's lock list, resulting
in use after free.
Reported-by: Eryu Guan <eguan@redhat.com>
Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Cc: <stable@vger.kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Add Link UP/Down prints to kernel log when link state changes
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Valid weight assigned to ETS TClass values are 1-100
Fixes: 08fb1dacdd76 ('net/mlx5e: Support DCBNL IEEE ETS')
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default fallback function used by mlx5e select queue can return
any TX queues in range [0..dev->num_real_tx_queues).
The current implementation assumes that the fallback function returns
a number in the range [0.. number of channels). Actually
dev->num_real_tx_queues = (number of channels) * dev->num_tc;
which is more than the expected range if num_tc is configured and could
lead to crashes.
To fix this we test if num_tc is not configured we can safely return the
fallback suggestion, if not we will reciprocal_scale the fallback
result and normalize it to the desired range.
Fixes: 08fb1dacdd76 ('net/mlx5e: Support DCBNL IEEE ETS')
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ConnectX4-Lx uses an inline wqe mode that currently defaults to
requiring the entire L2 header be included in the wqe.
This patch fixes mlx5e_get_inline_hdr_size() to account for
all L2 headers (VLAN, QinQ, etc) using skb_network_offset(skb).
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a timeout to avoid an infinite loop waiting for RQ's to flush. This
occurs during AER/EEH and will also happen if the device stops posting
completions due to internal error or reset, or if moving the RQ to the
error state fails. Also cleanup posted receive resources when closing
the RQ.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add callback to handle TX timeouts.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid an infinite loop by timing out waiting for the SQ to flush. Also
clean up the TX descriptors if that happens.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation does not handle timeout in case of command
with callback request, and this can lead to deadlock if the command
doesn't get fw response.
Add delayed callback timeout work before posting the command to fw.
In case of real fw command completion we will cancel the delayed work.
In case of fw command timeout the callback timeout handler will be
called and it will simulate fw completion with timeout error.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call command completion handler in case of timeout when working in
interrupts mode.
Avoid flushing the commands workqueue after acquiring the semaphores to
prevent a potential deadlock.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device ID for VFs is in a different location than PFs. This results
in the poll always timing out for VFs. There's no good way to read the
VF device ID without using the PF's configuration space. Switch to waiting
for the health poll to start incrementing. Also remove the 1s sleep
at the beginning.
fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core
driver')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change page cleanup flow when in internal error to properly decrement
the page counts when reclaiming pages. The prevents timing out waiting
for extra pages that were actually cleaned up previously.
fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In internal error state the health poll thread will eventually call
synchronize_irq() (to safely trigger command completions) which might
sleep, so we are calling sleeping function from atomic context which is
invalid.
Here we move trigger_cmd_completions(dev) to enter error state which is
the earliest stage in error state handling.
This way we won't need to wait for next health poll to trigger command
completions and will solve the scheduling while atomic issue.
mlx5_enter_error_state can be called from two contexts, protect it with
dev->intf_state_lock
Fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of internal error state we will simulate the commands status
through the return value translation function, but we need to simulate
all the teardown fw commands as successful so we will not have fw
command failure prints.
This also fix memory leaks that happen because we skip teardown stages
due to failed fw commands.
Fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ether_addr_equal_64bits() requires some care about its arguments,
namely that 8 bytes might be read, even if last 2 byte values are not
used.
KASan detected a violation with null_mac_addr and lacpdu_mcast_addr
in bond_3ad.c
Same problem with mac_bcast[] and mac_v6_allmcast[] in bond_alb.c :
Although the 8-byte alignment was there, KASan would detect out
of bound accesses.
Fixes: 815117adaf5b ("bonding: use ether_addr_equal_unaligned for bond addr compare")
Fixes: bb54e58929f3 ("bonding: Verify RX LACPDU has proper dest mac-addr")
Fixes: 885a136c52a8 ("bonding: use compare_ether_addr_64bits() in ALB")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default value of reg-2f in codec rt5650 is 0x5002, not 0x1002.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If mvneta_mdio_probe() fails, a kernel warning is triggered due to
missing cleanup in the error path. Add the necessary cleanup.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 281 at kernel/irq/manage.c:1814 __free_percpu_irq+0xfc/0x130
percpu IRQ 38 still enabled on CPU0!
Modules linked in: bnep bluetooth xhci_plat_hcd xhci_hcd marvell_cesa armada_thermal des_generic ehci_orion mcp3021 spi_orion sfp mdio_i2c evbug fuse
CPU: 1 PID: 281 Comm: connmand Not tainted 4.7.0-rc2+ #53
Hardware name: Marvell Armada 380/385 (Device Tree)
Backtrace:
[<c0013488>] (dump_backtrace) from [<c00137d0>] (show_stack+0x18/0x1c)
r6:60010093 r5:ffffffff r4:00000000 r3:dc8ba500
[<c00137b8>] (show_stack) from [<c02c6fe0>] (dump_stack+0xa4/0xdc)
[<c02c6f3c>] (dump_stack) from [<c002d4ec>] (__warn+0xd8/0x104)
r6:c081e6a0 r5:00000000 r4:edfe5d50 r3:dc8ba500
[<c002d414>] (__warn) from [<c002d5d0>] (warn_slowpath_fmt+0x40/0x48)
r10:a0010013 r8:c09356f8 r7:00000026 r6:ef11a260 r5:edd7b980 r4:ef11a200
[<c002d594>] (warn_slowpath_fmt) from [<c008c8e0>] (__free_percpu_irq+0xfc/0x130)
r3:00000026 r2:c081e7ac
[<c008c7e4>] (__free_percpu_irq) from [<c008c95c>] (free_percpu_irq+0x48/0x74)
r10:00008914 r8:00000000 r7:ffffffed r6:c09356f8 r5:00000026 r4:ef11a200
[<c008c914>] (free_percpu_irq) from [<c043dd70>] (mvneta_open+0x118/0x134)
r6:ffffffed r5:ef01e640 r4:ef01e000 r3:ef01e000
[<c043dc58>] (mvneta_open) from [<c055f5b4>] (__dev_open+0xa4/0x108)
r7:ef01e030 r6:c06ff3d8 r5:ffff9003 r4:ef01e000
[<c055f510>] (__dev_open) from [<c055f844>] (__dev_change_flags+0x94/0x150)
r7:00001002 r6:00000001 r5:ffff9003 r4:ef01e000
[<c055f7b0>] (__dev_change_flags) from [<c055f938>] (dev_change_flags+0x20/0x50)
r8:00000000 r7:c09334c8 r6:00001002 r5:00000148 r4:ef01e000 r3:00008914
[<c055f918>] (dev_change_flags) from [<c05de044>] (devinet_ioctl+0x6f4/0x7e0)
r8:00000000 r7:c09334c8 r6:00000000 r5:ee87200c r4:00000000 r3:00008914
[<c05dd950>] (devinet_ioctl) from [<c05e0168>] (inet_ioctl+0x1b8/0x1c8)
r10:beb4499c r9:edfe4000 r8:ecf13280 r7:c096cf00 r6:beb4499c r5:eef7c240
r4:00008914
[<c05dffb0>] (inet_ioctl) from [<c053c898>] (sock_ioctl+0x78/0x300)
[<c053c820>] (sock_ioctl) from [<c0155ecc>] (do_vfs_ioctl+0x98/0xa60)
r7:00000011 r6:00008914 r5:00000011 r4:c01568d0
[<c0155e34>] (do_vfs_ioctl) from [<c01568d0>] (SyS_ioctl+0x3c/0x60)
r10:00000000 r9:edfe4000 r8:beb4499c r7:00000011 r6:00008914 r5:ecf13280
r4:ecf13280
[<c0156894>] (SyS_ioctl) from [<c000fe60>] (ret_fast_syscall+0x0/0x1c)
r8:c0010004 r7:00000036 r6:00000011 r5:000a2978 r4:00000000 r3:00009003
---[ end trace 711f625d5b04b3a7 ]---
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LINK_OFF_WAKE_EN should be cleared after autoresume, otherwise after
system suspend, the system would wake up when linking off occurs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We're making all reset line users specify whether their lines are
shared with other IP or they operate them exclusively. In this case
the line is exclusively used only by this IP, so use the *_exclusive()
API accordingly.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We're making all reset line users specify whether their lines are
shared with other IP or they operate them exclusively. In this case
the line is exclusively used only by this IP, so use the *_exclusive()
API accordingly.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
On the STiH410 B2120 development board the MiPHY28lp shares its reset
line with the Synopsys DWC3 SuperSpeed (SS) USB 3.0 Dual-Role-Device
(DRD). New functionality in the reset subsystems forces consumers to
be explicit when requesting shared/exclusive reset lines.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Call wmb() to ensure writes are complete before
hardware fetches updated Tx descriptors.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- m_start() in fs/namespace.c expects that ns->event is incremented each
time a mount added or removed from ns->list.
- umount_tree() removes items from the list but does not increment event
counter, expecting that it's done before the function is called.
- There are some codepaths that call umount_tree() without updating
"event" counter. e.g. from __detach_mounts().
- When this happens m_start may reuse a cached mount structure that no
longer belongs to ns->list (i.e. use after free which usually leads
to infinite loop).
This change fixes the above problem by incrementing global event counter
before invoking umount_tree().
Change-Id: I622c8e84dcb9fb63542372c5dbf0178ee86bb589
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Ulanov <andreyu@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
Dmitri Epshtein
Martin KaFai Lau
Vegard Nossum
Dan Carpenter
Ganesh Goudar
Or Gerlitz
Aviv Heller
hayeswang
Torsten Hilbrich
Ursula Braun
David S. Miller
Christophe Jaillet
Bjørn Mork
Haishuang Yan
Takashi Iwai
Linus Torvalds
Vivek Goyal
Stefan Hauser
Sergio Valverde
Matt Corallo
Ralf Baechle
Richard Alpe
Florian Fainelli
Daniel Borkmann
WANG Cong
Miklos Szeredi
Shaker Daibes
Rana Shahout
Matthew Finlay
Daniel Jurgens
Mohamad Haj Yahia
Eric Dumazet
Bard Liao
Russell King - ARM Linux
Lee Jones
Sony Chacko
Andrey Ulanov