| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch implements XDP transmission for TAP. Since we can't create
new queues for TAP during XDP set, exist ptr_ring was reused for
queuing XDP buffers. To differ xdp_buff from sk_buff, TUN_XDP_FLAG
(0x1UL) was encoded into lowest bit of xpd_buff pointer during
ptr_ring_produce, and was decoded during consuming. XDP metadata was
stored in the headroom of the packet which should work in most of
cases since driver usually reserve enough headroom. Very minor changes
were done for vhost_net: it just need to peek the length depends on
the type of pointer.
Tests were done on two Intel E5-2630 2.40GHz machines connected back
to back through two 82599ES. Traffic were generated/received through
MoonGen/testpmd(rxonly). It reports ~20% improvements when
xdp_redirect_map is doing redirection from ixgbe to TAP (from 2.50Mpps
to 3.05Mpps)
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch switches to use ptr_ring instead of skb_array. This will be
used to enqueue different types of pointers by encoding type into
lower bits.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Preempt counter APIs have been split out, currently, hardirq.h just
includes irq_enter/exit APIs which are not used by TIPC at all.
So, remove the unused hardirq.h.
Signed-off-by: Yang Shi <yang.s@alibaba-inc.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Preempt counter APIs have been split out, currently, hardirq.h just
includes irq_enter/exit APIs which are not used by openvswitch at all.
So, remove the unused hardirq.h.
Signed-off-by: Yang Shi <yang.s@alibaba-inc.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: dev@openvswitch.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Preempt counter APIs have been split out, currently, hardirq.h just
includes irq_enter/exit APIs which are not used by caif at all.
So, remove the unused hardirq.h.
Signed-off-by: Yang Shi <yang.s@alibaba-inc.com>
Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the more appropriate netdev_WARN_ONCE instead of WARN_ONCE macro.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the more appropriate netdev_WARN_ONCE instead of WARN_ONCE macro.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the more appropriate netdev_WARN_ONCE instead of WARN_ONCE macro.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the more appropriate netdev_WARN_ONCE instead of WARN_ONCE macro.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the unnecessary line break between the netdev name and reg state
to the actual message that should be printed.
For example, this:
[86730.307236] ------------[ cut here ]------------
[86730.313496] netdevice: enp27s0f0
Message from the driver
[...]
Will be replaced with:
[86770.259289] ------------[ cut here ]------------
[86770.265191] netdevice: enp27s0f0: Message from the driver
[...]
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev_WARN_ONCE is broken (whoops..), this fix will remove the
unnecessary "condition" parameter, add the missing comma and change
"arg" to "args".
Fixes: 375ef2b1f0d0 ("net: Introduce netdev_*_once functions")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As of now, there're two sk_family are traced with sock:inet_sock_set_state,
which are AF_INET and AF_INET6.
So the sk_family are exposed as well.
Then we can conveniently use it to do the filter.
Both sk_family and sk_protocol are showed in the printk message, so we need
not expose them as tracepoint arguments.
Suggested-by: Brendan Gregg <brendan.d.gregg@gmail.com>
Suggested-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Reviewed-by: Song Liu <songliubraving@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TXALCR1 offsets are incorrect in the register offset tables, most
probably due to copy&paste error. Luckily, the driver never uses this
register. :-)
Fixes: 4a55530f38e4 ("net: sh_eth: modify the definitions of register")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the probing of the regulator is deferred, the memory allocated by
'mdiobus_alloc_size()' will be leaking.
It should be freed before the next call to 'sun4i_mdio_probe()' which will
reallocate it.
Fixes: 4bdcb1dd9feb ("net: Add MDIO bus driver for the Allwinner EMAC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "offset" option has been removed by
commit 900631ee6a26 ("l2tp: remove configurable payload offset").
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1463447 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mask argument for phy_modify() in several locations was inverted.
Fixes: fea23fb591cc ("net: phy: convert read-modify-write to phy_modify()")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported a hang involving SCTP, on which it kept flooding dmesg
with the message:
[ 246.742374] sctp: sctp_transport_update_pmtu: Reported pmtu 508 too
low, using default minimum of 512
That happened because whenever SCTP hits an ICMP Frag Needed, it tries
to adjust to the new MTU and triggers an immediate retransmission. But
it didn't consider the fact that MTUs smaller than the SCTP minimum MTU
allowed (512) would not cause the PMTU to change, and issued the
retransmission anyway (thus leading to another ICMP Frag Needed, and so
on).
As IPv4 (ip_rt_min_pmtu=556) and IPv6 (IPV6_MIN_MTU=1280) minimum MTU
are higher than that, sctp_transport_update_pmtu() is changed to
re-fetch the PMTU that got set after our request, and with that, detect
if there was an actual change or not.
The fix, thus, skips the immediate retransmission if the received ICMP
resulted in no change, in the hope that SCTP will select another path.
Note: The value being used for the minimum MTU (512,
SCTP_DEFAULT_MINSEGMENT) is not right and instead it should be (576,
SCTP_MIN_PMTU), but such change belongs to another patch.
Changes from v1:
- do not disable PMTU discovery, in the light of commit
06ad391919b2 ("[SCTP] Don't disable PMTU discovery when mtu is small")
and as suggested by Xin Long.
- changed the way to break the rtx loop by detecting if the icmp
resulted in a change or not
Changes from v2:
none
See-also: https://lkml.org/lkml/2017/12/22/811
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if PMTU discovery is disabled on a given transport, but the
configured value is higher than the actual PMTU, it is likely that we
will get some icmp Frag Needed. The issue is, if PMTU discovery is
disabled, we won't update the information and will issue a
retransmission immediately, which may very well trigger another ICMP,
and another retransmission, leading to a loop.
The fix is to simply not trigger immediate retransmissions if PMTU
discovery is disabled on the given transport.
Changes from v2:
- updated stale comment, noticed by Xin Long
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When loading the module after unloading it, the network interface would
not be enabled and thus wouldn't have a backend counterpart and unable
to be used by the guest.
The guest would face errors like:
[root@guest ~]# ethtool -i eth0
Cannot get driver information: No such device
[root@guest ~]# ifconfig eth0
eth0: error fetching interface information: Device not found
This patch initializes the state of the netfront device whenever it is
loaded manually, this state would communicate the netback to create its
device and establish the connection between them.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since both first_rx and rx_ring are the head of rx ring, it not
necessary to use two structure members to statically indicate
the head of rx ring. So first_rx is removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Devvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
flow_type in HWRM_FLOW_ALLOC is not being populated correctly due to
incorrect passing of pointer and size of l3_mask argument of is_wildcard().
Fixed this.
Fixes: db1d36a27324 ("bnxt_en: add TC flower offload flow_alloc/free FW cmds")
Signed-off-by: Sunil Challa <sunilkumar.challa@broadcom.com>
Reviewed-by: Sathya Perla <sathya.perla@broadcom.com>
Reviewed-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The two conditions triggering BUG_ON() are somewhat unrelated:
the tcp_skb_pcount() check is meant to catch TSO flaws, the
second one checks sanity of congestion window bookkeeping.
Split them into two separate BUG_ON() assertions on two lines,
so that we know which one actually triggers, when they do.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow a process bound to a VRF to connect to a linklocal address.
Currently, this fails because of a mismatch between the scope of the
linklocal address and the sk_bound_dev_if inherited by the VRF binding:
$ ssh -6 fe80::70b8:cff:fedd:ead8%eth1
ssh: connect to host fe80::70b8:cff:fedd:ead8%eth1 port 22: Invalid argument
Relax the scope check to allow the socket to be bound to the same L3
device as the scope id.
This makes ipv6 linklocal consistent with other relaxed checks enabled
by commits 1ff23beebdd3 ("net: l3mdev: Allow send on enslaved interface")
and 7bb387c5ab12a ("net: Allow IP_MULTICAST_IF to set index to L3 slave").
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the commit 888cc8c20cf ("sh_eth: remove EDMAC_BIG_ENDIAN") (geez,
I didn't realize that was 2 years ago!) the initializers in the SuperH
platform code for the 'sh_eth_plat_data::edmac_endian' stopped to matter,
so we can remove that field for good (not sure if it was ever useful --
SH7786 Ether has been reported to have the same EDMAC descriptor/register
endiannes as configured for the SuperH CPU)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The statistics of rx/tx packets size greater than 1518
are not detailed. This patch adds more statistics for
different packet size range.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a redundant semicolon, this patch removes it.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pause parameters include source address, transmit gap and pause time.
The default value of the pause source address is zero in the hardware.
Default pause parameters need to be set to the hardware. Also, when
setting new mac address, the pause source address need to be updated.
Fixes: 9dc2145d910e ("net: hns3: Add support for PFC setting in TM module")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When initializing the MAC, the MTU vlaue need to be set to the hardware
too. Otherwise, the MTU value of software will be different from the MTU
value of hardware.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when changing MTU, The new MTU must need to be set to netdevice.
Fixes: a8e8b7ff3517 ("net: hns3: Add support to change MTU in HNS3 hardware")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting MTU, actually what we do is configuring the max frame size
for the hardware. ETH_HLEN、ETH_FCS_LEN and VLAN_HLEN must need to be
considered. And the frame size which is less than the default value
should not be set to the hardware. Because in the hardware, the the max
frame size not only controls the RX packet size, but also controls the
TX packet size. the RX packets whose size are greater than the setting
value will be dropped.
This patch fixes the bug setting a error max frame size to hardware.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit a9c782822166 ("net: hns3: add support for set_pauseparam")
adds set_pauseparam support for ethtool cmd, but forgets to update
fc_mode_last_time when PFC mode is disabled in hclge_cfg_pauseparam().
The wrong fc_mode_last_time will be used to update flow control mode
when lldpad has been running. As a result, when using the ethtool
command "-a", user will get a wrong pause parameter.
This patch adds the fc_mode_last_time update when PFC mode is disabled.
Fixes: a9c782822166 ("net: hns3: add support for set_pauseparam")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The result of tqp statistics query was read with an
error position, fix it according to the user manual.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add packet statistics of netdev for ethtool -S, in
order to show the statistics data for current net
device.
Remove update_stats() calling because it has been
completed in hns3_get_netdev_stats().
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The member "stats_size" of struct hns3_stats is useless,
remove it and fix the macro definition which has uses this
struct.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The member "stats_offset" was designed to indicate the offset
of each member of struct ring_stats in struct hns3_enet_ring,
but forgot to add the offset of the member in struct ring_stats.
Fixes: 496d03e960a ("net: hns3: Add Ethtool support to HNS3 driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An error loop index was used while querying statistics data
of tqps, which may cause call trace.
Fixes: 496d03e960ae ("net: hns3: Add Ethtool support to HNS3 driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dropped tx/rx packets number of each tqp should also
be counted into the total drop tx/rx packets numbers.
Fixes: 76ad4f0ee74 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the HNS3_NIC_STATE_DOWN bit when NIC state changes.
When NIC is down, mask the packet statistics for querying
with ifconfig command. It's a common practice.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It takes more than 200 query response messages between
driver and IMP, while updating the packet statistics.
It's too heavy for IMP to update it per second.
Extend the update period of packet statistics data from
1 second to 300 seconds(if too long, the statistics may
overflow).
As a result, we need to update it while querying with
ifconfig tool to keep the statistics data fresh.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The igu_rx_err_pkt indicates the same error with
mac_rx_fcs_err_pkt_num, so remove it.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix spelling error "overrsize" --> "oversize".
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some members of packet statistics are named in different styles.
This patch unifies them with new internal name rules, the main
modification are below:
trans --> tx
rcv --> rx
rcb_q%d_tx --> txq#%d
rcb_q%d_rx --> rxq#%d
sw_err_cnt(tx side) --> tx_dropped
sw_err_cnt(rx side) --> rx_dropped
pkts --> packets
tx_err_cnt --> errors
rx_err_cnt --> errors
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rxvlan offload status can only be changed by PF. Initialize
the value of NETIF_F_HW_VLAN_CTAG_RX bit of hw_features for
VFS to false, make sure user can't be able to change it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds vlan filter enable switch to
support ethtool -K ethX rx-vlan-filter on/off.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Real devices may support scatter gather(SG), so enable SG on rmnet
devices to use GSO. GSO reduces CPU cycles by 20% for a rate of
146Mpbs for a single stream TCP connection.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TX checksum offload applies to TCP / UDP packets which are not
fragmented using the MAPv4 checksum trailer. The following needs to be
done to have checksum computed in hardware -
1. Set the checksum start offset and inset offset.
2. Set the csum_enabled bit
3. Compute and set 1's complement of partial checksum field in
transport header.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the MAPv4 packet format in conjunction with MAP commands,
a dummy DL checksum trailer will be appended to the packet. Before
this packet is sent out as an ACK, the DL checksum trailer needs to be
removed.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the MAPv4 packet format, receive checksum offload can be
enabled in hardware. The checksum computation over pseudo header is
not offloaded but the rest of the checksum computation over
the payload is offloaded. This applies only for TCP / UDP packets
which are not fragmented.
rmnet validates the TCP/UDP checksum for the packet using the checksum
from the checksum trailer added to the packet by hardware. The
validation performed is as following -
1. Perform 1's complement over the checksum value from the trailer
2. Compute 1's complement checksum over IPv4 / IPv6 header and
subtracts it from the value from step 1
3. Computes 1's complement checksum over IPv4 / IPv6 pseudo header and
adds it to the value from step 2
4. Subtracts the checksum value from the TCP / UDP header from the
value from step 3.
5. Compares the value from step 4 to the checksum value from the
TCP / UDP header.
6. If the comparison in step 5 succeeds, CHECKSUM_UNNECESSARY is set
and the packet is passed on to network stack. If there is a
failure, then the packet is passed on as such without modifying
the ip_summed field.
The checksum field is also checked for UDP checksum 0 as per RFC 768
and for unexpected TCP checksum of 0.
If checksum offload is disabled when using MAPv4 packet format in
receive path, the packet is queued as is to network stack without
the validations above.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Jason Wang
Yang Shi
Gal Pressman
Yafang Shao
Sergei Shtylyov
Christophe JAILLET
Guillaume Nault
Gustavo A. R. Silva
Russell King
Marcelo Ricardo Leitner
Eduardo Otubo
Zhu Yanjun
Venkat Duvvuru
Sunil Challa
Stefano Brivio
David Ahern
Jian Shen
Peng Li
Fuyun Liang
Subash Abhinov Kasiviswanathan