| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Replace VLAN_TAG_PRESENT with single bit flag and free up
VLAN.CFI overload. Now VLAN.CFI is visible in networking stack
and can be passed around intact.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wrap VLAN_PRESENT bit using macro like PKT_TYPE_* and CLONED_*,
as used by BPF code.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- Bump version strings, by Simon Wunderlich
- Fixup includes, by Sven Eckelmann (3 patches)
- Separate BATMAN_ADV_DEBUG from DEBUGFS, by Sven Eckelmann
- Fixup tracing log documentation, by Sven Eckelmann
- Use exclusive locks to secure netlink information dump transfers,
by Sven Eckelmann (8 patches)
- Move CRC16 dependency, by Sven Eckelmann
- Enable MCAST by default, by Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netperf udp stream shows that eth_type_trans takes certain cpu,
so adjust the mac address check order, and firstly check if it
is device address, and only check if it is multicast address
only if not the device address.
After this change:
To unicast, and skb dst mac is device mac, this is most of time
reduce a comparision
To unicast, and skb dst mac is not device mac, nothing change
To multicast, increase a comparision
Before:
1.03% [kernel] [k] eth_type_trans
After:
0.78% [kernel] [k] eth_type_trans
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
if list is NULL pointer, and the following access of list
will trigger panic, which is same as BUG_ON
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-11-14
This series contains updates to i40e and virtchnl.
Lance Roy updates i40e to use lockdep_assert_held() instead of
spin_is_locked(), since it is better suited to check locking
requirements.
Jan improves the code readability in XDP by adding the use of a local
variable. Provides protection on methods that create/modify/destroy
VF's via locking mechanism to prevent unstable behaviour and potential
kernel panics.
Krzysztof adds a hardware capability flag to indicate whether firmware
supports stopping the LLDP agent.
Patryk replaces the use of strncpy() with strlcpy() to ensure the buffer
is NULL terminated.
Mitch fixes the issue of trying to start nway on devices that do not
support auto-negotiation, by checking the autoneg state before
attempting to restart nway.
Alice updates virtchnl to keep the checks all together for ease of
readability and consistency. Also fixed a "off by one" error in the
number of traffic classes being calculated.
Richard fixed VF port VLANs, where the priority bits were incorrectly
set because the incorrect shift and mask bits were being used.
Alan adds a bit to set and check if a timeout recovery is already
pending to prevent overlapping transmit timeout recovery.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
lib/test_objagg.c: In function ‘test_delta_action_item’:
./include/linux/printk.h:308:2: warning: ‘errmsg’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ido Schimmel says:
====================
mlxsw: spectrum: acl: Introduce ERP sharing by multiple masks
Jiri says:
The Spectrum-2 hardware has limitation number of ERPs per-region. In
order to accommodate more masks than number of ERPs, the hardware
supports to insert rules with delta bits. By that, the rules with masks
that differ in up-to 8 consecutive bits can share the same ERP.
Patches 1 and 2 fix couple of issues that would appear in existing
selftests after adding delta support
Patch 3 introduces a generic object aggregation library. Now it is
static, but it will get extended for recalculation of aggregations in
the future in order to reach more optimal aggregation.
Patch 4 just simply converts existing ERP code to use the objagg library
instead of a rhashtable.
Patches 5-9 do more or less small changes to prepare ground for the last
patch.
Patch 10 fills-up delta callbacks of objagg library and utilizes the
delta bits for rule insertion.
The last patch adds selftest to test the mlxsw Spectrum-2 delta flows.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Track the basic codepaths of delta handling, using objagg tracepoints.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow ERP sharing for multiple mask. Do it by properly implementing
delta_create() objagg object. Use the computed delta info for inserting
rules in A-TCAM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Later on the same code is going to be needed for deltas as well. So push
the procedures related to increment and decrement of num_ctcam_erps
into a separate helpers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since two remaining users of mlxsw_afk_encode() do not specify
block ranges to work on, remove the args. Also, key/mask is always
non-NULL now, so skip the checks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to do key encoding again in
mlxsw_sp_acl_atcam_12kb_lkey_id_get(). Instead of that, introduce
a new helper that would just clear unused blocks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change order so it is aligned with the usual case where the "write_to"
buffer comes as the first arg.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device requires that the master mask of each region will be
composed from a logical OR between all the unmasked bits in the region.
Currently, this is just a logical OR between all the eRPs used in the
region, but the next patch is going to introduce delta bits support
which need to be taken into account as well.
Since the eRP does not include the delta bits, pass the key pointer to
mlxsw_sp_acl_erp_master_mask_set/clear instead. Convert key->mask to
the bitmap on fly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the ERPs are tracked internally in a hashtable. Benefit from
the newly introduced objagg library and use it to track ERPs. At this
point, there is no nesting of objects done, as the delta_create callback
always returns -EOPNOTSUPP. On the way, add "mask" into ERP mask get and
set functions and struct names.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This lib tracks objects which could be of two types:
1) root object
2) nested object - with a "delta" which differentiates it from
the associated root object
The objects are tracked by a hashtable and reference-counted. User is
responsible of implementing callbacks to create/destroy root entity
related to each root object and callback to create/destroy nested object
delta.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for this to behave as required with delta bits, change the mask
for rule with handle 103.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for this to behave as required with delta bits, change the mask
for rule with handle 103.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__tcp_checksum_complete() is 100% same with __skb_checksum_complete()
and there is no other caller except tcp_checksum_complete().
So, just use __skb_checksum_complete() there.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added support in tc flower for filtering based on port ranges.
Example:
1. Match on a port range:
-------------------------
$ tc filter add dev enp4s0 protocol ip parent ffff:\
prio 1 flower ip_proto tcp dst_port range 20-30 skip_hw\
action drop
$ tc -s filter show dev enp4s0 parent ffff:
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
ip_proto tcp
dst_port range 20-30
skip_hw
not_in_hw
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 85 sec used 3 sec
Action statistics:
Sent 460 bytes 10 pkt (dropped 10, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
2. Match on IP address and port range:
--------------------------------------
$ tc filter add dev enp4s0 protocol ip parent ffff:\
prio 1 flower dst_ip 192.168.1.1 ip_proto tcp dst_port range 100-200\
skip_hw action drop
$ tc -s filter show dev enp4s0 parent ffff:
filter protocol ip pref 1 flower chain 0 handle 0x2
eth_type ipv4
ip_proto tcp
dst_ip 192.168.1.1
dst_port range 100-200
skip_hw
not_in_hw
action order 1: gact action drop
random type none pass val 0
index 2 ref 1 bind 1 installed 58 sec used 2 sec
Action statistics:
Sent 920 bytes 20 pkt (dropped 20, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
v4:
1. Added condition before setting port key.
2. Organized setting and dumping port range keys into functions
and added validation of input range.
v3:
1. Moved new fields in UAPI enum to the end of enum.
2. Removed couple of empty lines.
v2:
Addressed Jiri's comments:
1. Added separate functions for dst and src comparisons.
2. Removed endpoint enum.
3. Added new bit TCA_FLOWER_FLAGS_RANGE to decide normal/range
lookup.
4. Cleaned up fl_lookup function.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently netdev_rx_csum_fault() only shows a device name,
we need more information about the skb for debugging csum
failures.
Sample output:
ens3: hw csum failure
dev features: 0x0000000000014b89
skb len=84 data_len=0 pkt_type=0 gso_size=0 gso_type=0 nr_frags=0 ip_summed=0 csum=0 csum_complete_sw=0 csum_valid=0 csum_level=0
Note, I use pr_err() just to be consistent with the existing one.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already have a workaround for a couple of switches whose internal
PHYs only have the Marvel OUI, but no model number. We detect such
PHYs and give them the 6390 ID as the model number. However the
mv88e6161 has two SERDES interfaces in the same address range as its
internal PHYs. These suffer from the same problem, the Marvell OUI,
but no model number. As a result, these SERDES interfaces were getting
the same PHY ID as the mv88e6390, even though they are not PHYs, and
the Marvell PHY driver was trying to drive them.
Add a special case to stop this from happen.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-11-13
This series contains updates to the ice driver only.
Brett cleans up debug print messages by removing useless or duplicate
messages, and make sure we assign the hardware head pointer to head
instead of the software head pointer. Resolved an issue when disabling
SRIOV we were trying to stop queues multiple times, so make sure we
disable SRIOV before stopping transmit and receive queues for VF.
Tony fixes a potential NULL pointer dereference during a VF reset.
Anirudh resolves an issue where we were releasing the VSI before
removing the VSI scheduler node, which was resulting in an error "Failed
to set LAN Tx queue context, error: -1". Also fixed the guaranteed
number of VSIs available and used by discovering the device
capabilities to determine the 'guar_num_vsi' per function, rather than
always using the theoretical max number of VSIs every time.
Dave avoids a deadlock by nesting RTNL locking, so added a boolean to
determine if the RTNL lock is already held.
Lev fixes bad mask values which would break compilation.
Piotr increases the receive queue disable timeout since it can take
additional time to finish all pending queue requests.
Usha resolves an issue of VLAN priority tagged traffic not appearing on
all traffic classes, which was causing ETS bandwidth shaping to not work
as expected.
Henry fixes the reset path to cleanup the old scheduler tree before
rebuilding it.
Md Fahad removes a unnecessary check which was causing a driver load
error on platforms with more than 128 cores.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Salil Mehta says:
====================
net: hns3: Add support of hardware GRO to HNS3 Driver
This patch-set adds support of hardware assisted GRO feature to
HNS3 driver on Rev B(=0x21) platform. Current hardware only
supports TCP/IPv{4|6} flows.
Change Log:
V1->V2:
1. Remove redundant print reported by Leon Romanovsky.
Link: https://lkml.org/lkml/2018/11/13/715
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When HW GRO enable, protocol stack will not do GRO again,
driver should add gro param to the skb for the protocol
stack..
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MAX_SKB_FRAGS in protocol stack is defined as:
MAX_SKB_FRAGS is 17 when PAGE_SIZE is 4K. If HW enable GRO, it may
merge small packets and the rx buffer may be more than
MAX_SKB_FRAGS. So driver will add skb chain when RX buffer num.
more than MAX_SKB_FRAGS.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support of ethtool -K to enable/disable
hardware GRO in HNS3 PF/VF driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "FE bit" in the description means the last description for
a packets. When HW GRO enable, HW write data to ring every
packet/buffer, there is greater probability that driver handle
with the describtion but HW still not set the "FE bit".
When drier handle the packet and HW still not set "FE bit",
driver stores skb and bd_num in rx ring, and continue to use the
skb and bd_num in next napi.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HNS3 hardware Revision B(=0x21) supports Hardware GRO feature. This
patch enables this feature in the HNS3 PF/VF driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move IRQ configuration for IP101A/G from config_init to config_intr
callback. Reasons:
1. This allows phylib to disable interrupts if needed.
2. Icplus was the only driver supporting interrupts w/o defining a
config_intr callback. Now we can add a phylib plausibility check
disabling interrupt mode if one of the two irq-related callbacks
isn't defined.
I don't own hardware with this PHY, and the change is based on the
datasheet for IP101A LF (which is supposed to be register-compatible
with IP101A/G). Change is compile-tested only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a TX hang occurs, we attempt to recover by incrementally resetting.
If we're starved for CPU time, it's possible the reset doesn't actually
complete (or even fire) before another tx_timeout fires causing us to
fly through the different resets without actually doing them.
This adds a bit to set and check if a timeout recovery is already
pending and, if so, bail out of tx_timeout. The bit will get cleared at
the end of i40e_rebuild when reset is complete.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The i40e driver complains about unprivileged VFs trying to configure
promiscuous mode each time a VF reset occurs. This isn't the fault of
the poor VF driver - the PF driver itself is making the request.
To fix this, skip the privilege check if the request is to disable all
promiscuous activity. This gets rid of the bogus message, but doesn't
affect privilege checks, since we really only care if the unprivileged
VF is trying to enable promiscuous mode.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When using port VLAN, for VFs, and setting priority bits, the device
was sending out incorrect priority bits, and also setting the CFI
bit incorrectly.
To fix this, changed shift and mask bit definition for this function, to
use the correct ones.
Signed-off-by: Richard Rodriguez <richard.rodriguez@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When calculating the valid length for a VIRTCHNL_OP_ENABLE_CHANNELS
message, we accidentally allowed messages with one extra
virtchnl_channel_info structure on the end. This happened due
to an off by one error, because we forgot that valid_len already
accounted for one virtchnl_channel_info structure, so we need to
subtract one from the num_tc value.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
White space change.
Move the check on the virtchnl_vsi_queue_config_info struct
to be close to the struct like all the other similar checks.
This keeps it clearer and easier to read.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In i40e_get_settings_link_up, set ks->base.speed to SPEED_UNKNOWN
in the case where we don't know the link speed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On link types that do not support autoneg, we cannot attempt to restart
nway negotiation. This results in a dead link that requires a power
cycle to remedy.
Fix this by saving off the autoneg state and checking this value before
we try to restart nway.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch allows disabling FW LLDP agent on X722 devices.
It also changes a source of information for this feature from
pf->hw_features to pf->hw.flags which are set in i40e_init_adminq.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The version numbers have not been kept up to date and this is
an effort to ammend that.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A scenario has been found in which simultaneous
addition/removal and modification of VF's might cause
unstable behaviour, up to and including kernel panics.
Protect the methods that create/modify/destroy VF's
by locking them behind an atomically set bit in PF status
bitfield.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Using strncpy allows destination buffer to be not null terminated
after the copying takes place. strlcpy ensures that's not the
case by explicitly setting last element in the buffer as '\0'.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add HW capability flag to indicate that firmware supports stopping
LLDP agent. This feature has been added in FW API 1.7 for XL710
devices and 1.6 for X722. Also raise expected minor version number
for X722 FW API to 6.
Signed-off-by: Krzysztof Galazka <krzysztof.galazka@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use a local variable to make the code a bit more readable.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
lockdep_assert_held() is better suited to checking locking requirements,
since it won't get confused when someone else holds the lock. This is
also a step towards possibly removing spin_is_locked().
Signed-off-by: Lance Roy <ldr709@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Jakub Kicinski says:
====================
nfp: abm: track all Qdiscs
Our Qdisc offload so far has been very simplistic. We held
and array of marking thresholds and statistics sized to the
number of PF queues. This was sufficient since the only
configuration we supported was single layer of RED Qdiscs
(on top of MQ or not, but MQ isn't really about queuing).
As we move to add more Qdiscs it's time to actually try to
track the full Qdisc hierarchy. This allows us to make sure
our offloaded configuration reflects the SW path better.
We add graft notifications to MQ and RED (PRIO already sends
them) to allow drivers offloading those to learn how Qdiscs
are linked. MQ graft gives us the obvious advantage of being
able to track when Qdiscs are shared or moved. It seems
unlikely HW would offload RED's child Qdiscs but since the
behaviour would change based on linked child we should
stop offloading REDs with modified child. RED will also
handle the child differently during reconfig when limit
parameter is set - so we have to inform the drivers about
the limit, and have them reset the child state when
appropriate.
The NFP driver will now allocate a structure to track each
Qdisc and link it to its children. We will also maintain
a shadow copy of threshold settings - to save device writes
and make it easier to apply defaults when config is
re-evaluated.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Michał Mirosław
David S. Miller
Li RongQing
Jiri Pirko
Cong Wang
Amritha Nambiar
Andrew Lunn
Peng Li
Heiner Kallweit
Alan Brady
Mitch Williams
Richard Rodriguez
Alice Michael
Jacob Keller
Patryk Małek
Jan Sokolowski
Krzysztof Galazka
Lance Roy