| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
LTC3887 is an enhanced version of LTC3880 and supports the same commands.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Per datasheet, the chip ID for LTM4676 is 0x448x. This was observed
in real systems. In addition to that, chip ID 0x4401 was observed
as well. Research shows that the chip ID has been changed from 0x440x
to 0x448x in datasheet revision C. Add support for the additional chip ID.
Also add the chip ID for LTM4676A, which is functionally identical
to LTM4676.
Reported-by: Ananda Babu Nettam <anandab@juniper.net>
Cc: Ananda Babu Nettam <anandab@juniper.net>
Cc: Amit U Jain <amjain@juniper.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
LTC3882 is mostly compatible with LTC3880. Major differences are that it
does not measure the input current, and it no longer supports LTC's legacy
mechanism to identify the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Verifying the chip type is getting more complicated with new chips,
since not all chips support the same mechanism to read the chip type.
Move the code into a separate function to simplify adding support for
those chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This change sht15_reverse() to be generic bitrev8().
Signed-off-by: yalin wang <yalin.wang2010@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add device IDs and references for Texas Instruments TPS544B20, TPS544B25,
TPS544C20, and TPS544C25 to the generic PMBus driver.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
MAX20751 is a multiphase power controller with internal buck converter.
It uses VR12.0 to report the output voltage. This requires an explicit
driver, since the VR version can not be auto-detected.
The chip supports a manufacturer specific command to fine-tune the output
voltage. This command is not currently supported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Newer chips such as MAX20751 support VR12. Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the IT8732F. This chip is pretty similar to IT8721F,
with the main difference being that the ADC LSB is 10.9 mV instead of
12 mV.
Signed-off-by: Justin Maggard <jmaggard@netgear.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Introduced REG_PWM, pwm[1..3]_auto_point[1..5]_temp,
pwm[1..3]_auto_point[1..5]_pwm, nct7802_auto_point_attrs,
nct7802_auto_point_group, updated nct7802_regmap_is_volatile
Signed-off-by: Constantine Shulyupin <const@MakeLinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Allow the lm70 to be probed from a device tree.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use the CLEAR_PEAKS command on LTM4676.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
ADM1293 and ADM1294 are mostly compatible with other chips of the same
series, but have more configuration options. There are also some
differences in register details.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for powerX_input_lowest for both input and output power.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Introduce have_vout, have_vaux_status, have_pin_max, and have_uc_fault
to simplify adding support for new chips.
Also simplify error returns where appropriate to return immediately
on error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Each new chip supported by the driver has a new set of coefficients,
making hard-coding coefficients more and more cumbersome. Introduce
a datastructure and table to simplify configuration.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use BIT macro to simplify adding new bit masks.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
pmbus_regulator_ops is not modified after initialized, so make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The pmbus_regulator_ops is for voltage regulators, so explicitly set
regulator type for better readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add f81768d (id 0x1210) currently found on Jetway motherboards.
It has 11 voltages but otherwise needed no special handling
in this driver.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Introduced REG_SMARTFAN_EN, SMARTFAN_EN_SHIFT, pwmX_enable,
show_pwm_enable, store_pwm_enable.
Signed-off-by: Constantine Shulyupin <const@MakeLinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The f81866a voltage-1 protector(VIN1) address
is differ from f71882.
f71882 status:12H, beep:13H, v-high:32H
f81866a status:16H, beep:17H, v-high:3aH
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The temperature value of Fintek F81866 is the same with
f71882fg. It located with 0x6c + 2*(nr), others located
with 0x6c + 2*(nr+1). We change the rule in f71882fg_probe(),
If type = f71858fg/f8000/f81866a. the temp_start will set to 0,
others are 1.
The F81866 over-temperature beep setting is not the same with
f71882fg too. They are using the same address 63H, but F81866 is
using bit 0/1/2 & 4/5/6, others are using bit 1/2/3 & 5/6/7,
So we copy from fxxxx_temp_beep_attr[] to f81866_temp_beep_attr
and change bit setting.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add New Fintek SuperIO F81866(0x1010) & F71868(0x1106)
with H/W Monitor functions.
We increased F71882FG_MAX_INS from 9 to 10 to read
F71868 10 voltage sets.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Introduced: show_pwm_mode, pwm1_mode, pwm2_mode, pwm2_mode
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Added fan output control registers.
Modes of operation are PWM (default) and DC.
Introduced show_pwm, store_pwm, nct7802_pwm_attrs, nct7802_pwm_group.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Sensor type:
3 diode (current mode), MD=1
4 thermistor, MD=2
Reference:
Nuvoton Hardware Monitoring IC NCT7802Y
7.2.32 Mode Selection Register
Location : Index 22h
Signed-off-by: Constantine Shulyupin <const@MakeLinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
Pull input subsystem fixes from Dmitry Torokhov:
"Just small ALPS and Elan touchpads, and other driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add special check for fw_version 0x470f01 touchpad
Input: twl4030-vibra - fix ERROR: Bad of_node_put() warning
Input: alps - only Dell laptops have separate button bits for v2 dualpoint sticks
Input: axp20x-pek - add module alias
Input: turbografx - fix potential out of bound access
|
|
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.2. No area does particularly stand
out but we have a two unpleasant ones:
- Kernel ptes are marked with a global bit which allows the kernel to
share kernel TLB entries between all processes. For this to work
both entries of an adjacent even/odd pte pair need to have the
global bit set. There has been a subtle race in setting the other
entry's global bit since ~ 2000 but it take particularly
pathological workloads that essentially do mostly vmalloc/vfree to
trigger this.
This pull request fixes the 64-bit case but leaves the case of 32
bit CPUs with 64 bit ptes unsolved for now. The unfixed cases
affect hardware that is not available in the field yet.
- Instruction emulation requires loading instructions from user space
but the current fast but simplistic approach will fail on pages
that are PROT_EXEC but !PROT_READ. For this reason we temporarily
do not permit this permission and will map pages with PROT_EXEC |
PROT_READ.
The remainder of this pull request is more or less across the field
and the short log explains them well"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Make set_pte() SMP safe.
MIPS: Replace add and sub instructions in relocate_kernel.S with addiu
MIPS: Flush RPS on kernel entry with EVA
Revert "MIPS: BCM63xx: Provide a plat_post_dma_flush hook"
MIPS: BMIPS: Delete unused Kconfig symbol
MIPS: Export get_c0_perfcount_int()
MIPS: show_stack: Fix stack trace with EVA
MIPS: do_mcheck: Fix kernel code dump with EVA
MIPS: SMP: Don't increment irq_count multiple times for call function IPIs
MIPS: Partially disable RIXI support.
MIPS: Handle page faults of executable but unreadable pages correctly.
MIPS: Malta: Don't reinitialise RTC
MIPS: unaligned: Fix build error on big endian R6 kernels
MIPS: Fix sched_getaffinity with MT FPAFF enabled
MIPS: Fix build with CONFIG_OF=y for non OF-enabled targets
CPUFREQ: Loongson2: Fix broken build due to incorrect include.
|
|
Pull btrfs fix from Chris Mason:
"We have a btrfs quota regression fix.
I merged this one on Thursday and have run it through tests against
current master.
Normally I wouldn't have sent this while you were finalizing rc6, but
I'm feeding mosquitoes in the adirondacks next week, so I wanted to
get this one out before leaving. I'll leave longer tests running and
check on things during the week, but I don't expect any problems"
* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: qgroup: Fix a regression in qgroup reserved space.
|
|
Pull thermal management fixes from Zhang Rui:
"Specifics:
- fix an error that "weight_attr" sysfs attribute is not removed
while unbinding. From: Viresh Kumar.
- fix power allocator governor tracing to return the real request.
From Javi Merino.
- remove redundant owner assignment of hisi platform thermal driver.
From Krzysztof Kozlowski.
- a couple of small fixes of Exynos thermal driver. From Krzysztof
Kozlowski and Chanwoo Choi"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Drop owner assignment from platform_driver
thermal: exynos: Remove unused code related to platform_data on probe()
thermal: exynos: Add the dependency of CONFIG_THERMAL_OF instead of CONFIG_OF
thermal: exynos: Disable the regulator on probe failure
thermal: power_allocator: trace the real requested power
thermal: remove dangling 'weight_attr' device file
|
|
Pull ARC fixes from Vineet Gupta:
"Here's a late pull request for accumulated ARC fixes which came out of
extended testing of the new ARCv2 port with LTP etc. llock/scond
livelock workaround has been reviewed by PeterZ. The changes look a
lot but I've crafted them into finer grained patches for better
tracking later.
I have some more fixes (ARC Futex backend) ready to go but those will
have to wait for tglx to return from vacation.
Summary:
- Enable a reduced config of HS38 (w/o div-rem, ll64...)
- Add software workaround for LLOCK/SCOND livelock
- Fallout of a recent pt_regs update"
* tag 'arc-v4.2-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: spinlock/rwlock/atomics: reduce 1 instruction in exponential backoff
ARC: Make pt_regs regs unsigned
ARCv2: spinlock/rwlock: Reset retry delay when starting a new spin-wait cycle
ARCv2: spinlock/rwlock/atomics: Delayed retry of failed SCOND with exponential backoff
ARC: LLOCK/SCOND based rwlock
ARC: LLOCK/SCOND based spin_lock
ARC: refactor atomic inline asm operands with symbolic names
Revert "ARCv2: STAR 9000837815 workaround hardware exclusive transactions livelock"
ARCv2: [axs103_smp] Reduce clk for Quad FPGA configs
ARCv2: Fix the peripheral address space detection
ARCv2: allow selection of page size for MMUv4
ARCv2: lib: memset: Don't assume 64-bit load/stores
ARCv2: lib: memcpy: Missing PREFETCHW
ARCv2: add knob for DIV_REV in Kconfig
ARC/time: Migrate to new 'set-state' interface
|
|
Pull virtio fix from Michael Tsirkin:
"A last minute fix for the new virtio input driver. It seems pretty
obvious, and the problem it's fixing would be quite hard to debug"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-input: reset device and detach unused during remove
|
|
Pull device mapper fixes from Mike Snitzer:
- stable fix for a dm_merge_bvec() regression on 32 bit Fedora systems.
- fix for a 4.2 DM thinp discard regression due to inability to
properly delete a range of blocks in a data mapping btree.
* tag 'dm-4.2-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm btree remove: fix bug in remove_one()
dm: fix dm_merge_bvec regression on 32 bit systems
|
|
Pull sound fixes from Takashi Iwai:
"The only bulk changes in this request is ABI updates for ASoC topology
API. It's a new API that was introduced in 4.2, and we'd like to
avoid ABI change after the release, so it's taken now. As there is no
real in-tree user for this API, it should be fairly safe.
Other than that, the usual small fixes are found in various drivers:
ASoC cs4265, rt5645, intel-sst, firewire, oxygen and HD-audio"
* tag 'sound-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: topology: Add private data type and bump ABI version to 3
ASoC: topology: Add ops support to byte controls UAPI
ASoC: topology: Update TLV support so we can support more TLV types
ASoC: topology: add private data to manifest
ASoC: topology: Add subsequence in topology
ALSA: hda - one Dell machine needs the headphone white noise fixup
ALSA: fireworks/firewire-lib: add support for recent firmware quirk
Revert "ALSA: fireworks: add support for AudioFire2 quirk"
ASoC: topology: fix typo in soc_tplg_kcontrol_bind_io()
ALSA: HDA: Dont check return for snd_hdac_chip_readl
ALSA: HDA: Fix stream assignment for host in decoupled mode
ASoC: rt5645: Fix lost pin setting for DMIC1
ALSA: oxygen: Fix logical-not-parentheses warning
ASoC: Intel: sst_byt: fix initialize 'NULL device *' issue
ASoC: Intel: haswell: fix initialize 'NULL device *' issue
ASoC: cs4265: Fix setting dai format for Left/Right Justified
|
|
Pull hwmon fixes from Guenter Roeck:
- Export module alias information in g762 and nct7904 to support
auto-loading.
- Blacklist Dell Studio XPS 8100 in dell-smm to fix fan control
problems.
* tag 'hwmon-for-linus-v4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (g762) Export OF module alias information
hwmon: (nct7904) Export I2C module alias information
hwmon: (dell-smm) Blacklist Dell Studio XPS 8100
|
|
Pull USB fixes from Greg KH:
"Here are some USB and PHY fixes for 4.2-rc6 that resolve some reported
issues.
All of these have been in the linux-next tree for a while, full
details on the patches are in the shortlog below"
* tag 'usb-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
ARM: dts: dra7: Add syscon-pllreset syscon to SATA PHY
drivers/usb: Delete XHCI command timer if necessary
xhci: fix off by one error in TRB DMA address boundary check
usb: udc: core: add device_del() call to error pathway
phy: ti-pipe3: i783 workaround for SATA lockup after dpll unlock/relock
phy-sun4i-usb: Add missing EXPORT_SYMBOL_GPL for sun4i_usb_phy_set_squelch_detect
USB: sierra: add 1199:68AB device ID
usb: gadget: f_printer: actually limit the number of instances
usb: gadget: f_hid: actually limit the number of instances
usb: gadget: f_uac2: fix calculation of uac2->p_interval
usb: gadget: bdc: fix a driver crash on disconnect
usb: chipidea: ehci_init_driver is intended to call one time
USB: qcserial: Add support for Dell Wireless 5809e 4G Modem
USB: qcserial/option: make AT URCs work for Sierra Wireless MC7305/MC7355
|
|
Pull staging driver fixes from Greg KH:
"Here are three bugfixes for some staging driver issues that have been
reported. All have been in the linux-next tree for a while"
* tag 'staging-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: lustre: Include unaligned.h instead of access_ok.h
staging: vt6655: vnt_bss_info_changed check conf->beacon_rate is not NULL
staging: comedi: das1800: add missing break in switch
|
|
Pull char/misc fixes from Greg KH:
"Here are some extcon fixes for 4.2-rc6 that resolve some reported
problems.
All have been in linux-next for a while"
* tag 'char-misc-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
extcon: Fix extcon_cable_get_state() from getting old state after notification
extcon: Fix hang and extcon_get/set_cable_state().
extcon: palmas: Fix NULL pointer error
|
|
Pull drm fixes from Daniel Vetter:
"One i915 regression fix and a drm core one since Dave's not around,
both introduced in 4.2 so not cc: stable.
The fix for the warning Ted reported isn't in here yet since he didn't
yet supply a tested-by and I can't repro this one myself (it's in
fixup code that needs firmware doing something i915 wouldn't do)"
* tag 'drm-intel-fixes-2015-08-07' of git://anongit.freedesktop.org/drm-intel:
drm/vblank: Use u32 consistently for vblank counters
drm/i915: Allow parsing of variable size child device entries from VBT
|
|
It is no need to check the packet[0] for sanity check when doing
elantech_packet_check_v4() function for fw_version = 0x470f01 touchpad.
Signed-off by: Duson Lin <dusonlin@emc.com.tw>
Reviewed-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
remove_one() was not incrementing the key for the beginning of the
range, so not all entries were being removed. This resulted in
discards that were not unmapping all blocks.
Fixes: 4ec331c3ea ("dm btree: add dm_btree_remove_leaves()")
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
In
commit 99264a61dfcda41d86d0960cf2d4c0fc2758a773
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 15 19:34:43 2015 +0200
drm/vblank: Fixup and document timestamp update/read barriers
I've switched vblank->count from atomic_t to unsigned long and
accidentally created an integer comparison bug in
drm_vblank_count_and_time since vblanke->count might overflow the u32
local copy and hence the retry loop never succeed.
Fix this by consistently using u32.
Cc: Michel Dänzer <michel@daenzer.net>
Reported-by: Michel Dänzer <michel@daenzer.net>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
ASoC: Fixes for v4.2
There are a couple of small driver specific fixes here but the
overwhelming bulk of these changes are fixes to the topology ABI that
has been newly introduced in v4.2. Once this makes it into a release we
will have to firm this up but for now getting enhancements in before
they've made it into a release is the most expedient thing.
|
|
The increment of delay counter was 2 instructions:
Arithmatic Shfit Left (ASL) + set to 1 on overflow
This can be done in 1 using ROtate Left (ROL)
Suggested-by: Nigel Topham <ntopham@synopsys.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Pull sparc fix from David Miller:
"FPU register corruption bug fix"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix userspace FPU register corruptions.
|
|
Merge fixes from Andrew Morton:
"21 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (21 commits)
writeback: fix initial dirty limit
mm/memory-failure: set PageHWPoison before migrate_pages()
mm: check __PG_HWPOISON separately from PAGE_FLAGS_CHECK_AT_*
mm/memory-failure: give up error handling for non-tail-refcounted thp
mm/memory-failure: fix race in counting num_poisoned_pages
mm/memory-failure: unlock_page before put_page
ipc: use private shmem or hugetlbfs inodes for shm segments.
mm: initialize hotplugged pages as reserved
ocfs2: fix shift left overflow
kthread: export kthread functions
fsnotify: fix oops in fsnotify_clear_marks_by_group_flags()
lib/iommu-common.c: do not use 0xffffffffffffffffl for computing align_mask
mm/slub: allow merging when SLAB_DEBUG_FREE is set
signalfd: fix information leak in signalfd_copyinfo
signal: fix information leak in copy_siginfo_to_user
signal: fix information leak in copy_siginfo_from_user32
ocfs2: fix BUG in ocfs2_downconvert_thread_do_work()
fs, file table: reinit files_stat.max_files after deferred memory initialisation
mm, meminit: replace rwsem with completion
mm, meminit: allow early_pfn_to_nid to be used during runtime
...
|
|
If we have a series of events from userpsace, with %fprs=FPRS_FEF,
like follows:
ETRAP
ETRAP
VIS_ENTRY(fprs=0x4)
VIS_EXIT
RTRAP (kernel FPU restore with fpu_saved=0x4)
RTRAP
We will not restore the user registers that were clobbered by the FPU
using kernel code in the inner-most trap.
Traps allocate FPU save slots in the thread struct, and FPU using
sequences save the "dirty" FPU registers only.
This works at the initial trap level because all of the registers
get recorded into the top-level FPU save area, and we'll return
to userspace with the FPU disabled so that any FPU use by the user
will take an FPU disabled trap wherein we'll load the registers
back up properly.
But this is not how trap returns from kernel to kernel operate.
The simplest fix for this bug is to always save all FPU register state
for anything other than the top-most FPU save area.
Getting rid of the optimized inner-slot FPU saving code ends up
making VISEntryHalf degenerate into plain VISEntry.
Longer term we need to do something smarter to reinstate the partial
save optimizations. Perhaps the fundament error is having trap entry
and exit allocate FPU save slots and restore register state. Instead,
the VISEntry et al. calls should be doing that work.
This bug is about two decades old.
Reported-by: James Y Knight <jyknight@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Guenter Roeck
yalin wang
Justin Maggard
Constantine Shulyupin
Rabin Vincent
Axel Lin
Krzysztof Kozlowski
George Joseph
Peter Hung
Linus Torvalds
Duson Lin
Joe Thornber
Daniel Vetter
Takashi Iwai
Vineet Gupta
David S. Miller