aboutsummaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2016-05-17drivers: net: Don't print unpopulated net_device nameHarvey Hunt3-10/+20
For ethernet devices, net_device.name will be eth%d before register_netdev() is called. Don't print the net_device name until the format string is replaced. Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com> Cc: Marcel Ziswiler <marcel@ziswiler.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Barry Song <Baohua.Song@csr.com> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17qed: add support for dcbx.Sudarsana Reddy Kalluru11-8/+834
This patch adds the necessary driver support for Management Firmware to configure the device/firmware with the dcbx results. Management Firmware is responsible for communicating the DCBX and driving the negotiation, but the driver has responsibility of receiving async notification and configuring the results in hw/fw. This patch also adds the dcbx support for future protocols (e.g., FCoE) as preparation to their imminent submission. Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17ravb: Add missing free_irq() calls to ravb_close()Geert Uytterhoeven1-1/+6
When reopening the network device on ra7795/salvator-x, e.g. after a DHCP timeout: IP-Config: Reopening network devices... genirq: Flags mismatch irq 139. 00000000 (eth0:ch0:rx_be) vs. 00000000 (ravb e6800000.ethernet eth0: cannot request IRQ eth0:ch0:rx_be IP-Config: Failed to open eth0 IP-Config: No network devices available The "mismatch" is due to requesting an IRQ that is already in use, while IRQF_PROBE_SHARED wasn't set. However, the real cause is that ravb_close() doesn't release any of the R-Car Gen3-specific secondary IRQs. Add the missing free_irq() calls to fix this. Fixes: f51bdc236b6c5835 ("ravb: Add dma queue interrupt support") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17qed: Remove a stray tabDan Carpenter1-1/+1
This line was indented more than it should be. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller1-6/+6
Jeff Kirsher says: ==================== 10GbE Intel Wired LAN Driver Updates 2016-05-16 This series contains 2 fixes to ixgbe only. Emil fixes transmit hangs when enabling SRIOV by swapping the parameters in GENMASK in order to generate the correct mask. Alex fixes his previous patch b83e30104bd9 ("ixgbe/ixgbevf: Add support for GSO partial") where he somehow transposed the location of setting the VLAN features in netdev->features and the configuration of the vlan_features. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: fec-mpc52xx: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-24/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: fec-mpc52xx: use phydev from struct net_devicePhilippe Reynes1-23/+20
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16bpf, doc: fix typo on bpf_asm descriptionsDaniel Borkmann1-8/+8
Fix description of some of the bpf_asm tool related jump instructions and generally move them to format A <op> k. Reported-by: Sebastian Amend <sebastian.amend@googlemail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is setEzequiel Garcia1-1/+6
Commit f748be531d70 ("stmmac: support new GMAC4") reverted a previous fix by mistake. This commit re-applies said fix: commit dec2165ff38a99f937fe61875d102c6c8596c815 Author: Sonic Zhang <sonic.zhang@analog.com> Date: Thu Jan 22 14:55:57 2015 +0800 stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set Clear the TX COE bit when force_thresh_dma_mode is set even hardware dma capability says support. Tested on BF609. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net> Tested on LPC4350 Hitex board. Fixes: f748be531d70 ("stmmac: support new GMAC4") Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Tested-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: fs-enet: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-24/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: fs-enet: use phydev from struct net_devicePhilippe Reynes5-26/+18
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16netlink: Fix dump skb leak/double freeHerbert Xu1-2/+5
When we free cb->skb after a dump, we do it after releasing the lock. This means that a new dump could have started in the time being and we'll end up freeing their skb instead of ours. This patch saves the skb and module before we unlock so we free the right memory. Fixes: 16b304f3404f ("netlink: Eliminate kmalloc in netlink dump operation.") Reported-by: Baozeng Ding <sploving1@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16tipc: check nl sock before parsing nested attributesRichard Alpe1-0/+3
Make sure the socket for which the user is listing publication exists before parsing the socket netlink attributes. Prior to this patch a call without any socket caused a NULL pointer dereference in tipc_nl_publ_dump(). Tested-and-reported-by: Baozeng Ding <sploving1@gmail.com> Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Acked-by: Jon Maloy <jon.maloy@ericsson.cm> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16fq_codel: fix memory limitation driftEric Dumazet1-1/+2
memory_usage must be decreased in dequeue_func(), not in fq_codel_dequeue(), otherwise packets dropped by Codel algo are missing this decrease. Also we need to clear memory_usage in fq_codel_reset() Fixes: 95b58430abe7 ("fq_codel: add memory limitation per queue") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: ftgmac100: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-14/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: ftgmac100: use phydev from struct net_devicePhilippe Reynes1-16/+8
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: gianfar: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-25/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: gianfar: use phydev from struct net_devicePhilippe Reynes3-32/+35
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16ixgbe: Fix VLAN features errorAlexander Duyck1-4/+4
It looks like at some point I somehow transposed the location of setting the VLAN features in netdev->features and the configuration of the vlan_features. As a result the driver is now generating a warning about vlan_features being setup incorrectly. This patch corrects that by placing the update of netdev->features to include the VLAN features so that it is after the point where we write netdev->features into netdev->vlan_features. Fixes: b83e30104bd9 ("ixgbe/ixgbevf: Add support for GSO partial") Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-16ixgbe: use correct mask when enabling sriovEmil Tantilov1-2/+2
Swap the parameters in GENMASK in order to generate the correct mask. This change fixes Tx hangs when enabling SRIOV. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-16net: also make sch_handle_egress() drop monitor readyDaniel Borkmann1-3/+3
Follow-up for 8a3a4c6e7b34 ("net: make sch_handle_ingress() drop monitor ready") to also make the egress side drop monitor ready. Also here only TC_ACT_SHOT is a clear indication that something went wrong. Hence don't provide false positives to drop monitors such as 'perf record -e skb:kfree_skb ...'. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net/hsr: Use setup_timer and mod_timer.Muhammad Falak R Wani1-8/+3
The function setup_timer combines the initialization of a timer with the initialization of the timer's function and data fields. The mulitiline code for timer initialization is now replaced with function setup_timer. Also, quoting the mod_timer() function comment: -> mod_timer() is a more efficient way to update the expire field of an active timer (if the timer is inactive it will be activated). Use setup_timer() and mod_timer() to setup and arm a timer, making the code compact and aid readablity. Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16Merge branch 'qed-next'David S. Miller5-103/+99
Yuval Mintz says: ==================== qed: IOV enhncements and fixups This is a follow-up on the recent patch series that adds SR-IOV support to qed. All content here is iov-related fixups [nothing terminal] and enhancements. Please consider applying this series to `net-next'. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16qed: VFs gracefully accept lack of PMYuval Mintz1-1/+1
VF's probe might log that it has no PM capability in its PCI configuration space. As this is a valid configuration, silence such prints. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16qed: Allow more than 16 VFsYuval Mintz1-0/+3
In multi-function modes, PFs are currently limited to using 16 VFs - But that limitation would also currently apply in case there's a single PCI function exposed, where no such restriction should have existed. This lifts the restriction for the default mode; User should be able to start the maximum number of VFs as appear in the PCI config space. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16qed: Reset link on IOV disableManish Chopra1-39/+51
PF updates its VFs' bulletin boards with link configurations whenever the physical carrier changes or whenever hyper-user explicitly requires some setting of the VFs link via the hypervisor's PF. Since the bulletin board is getting cleaned as part of the IOV disable flow on the PF side, re-enabling sriov would lead to a VF that sees the carrier as 'down', until an event causing the PF to re-fill the bulletin with the link configuration would occur. To fix this we simply refelect the link state during the flows, giving the later VFs a default reflecting the PFs link state. Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16qed: Improve VF interrupt resetYuval Mintz4-60/+41
During FLR flow, need to make sure HW is no longer capable of writing to host memory as part of its interrupt mechanisms. While we're at it, unify the logic cleaning the driver's status-blocks into using a single API function for both PFs and VFs. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16qed: Correct PF-sanity checkYuval Mintz1-3/+3
Seems like something broke in commit 1408cc1fa48c ("qed: Introduce VFs") and the function no longer verifies that the vf is indeed a valid one. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net/mlx4_core: Fix access to uninitialized indexTariq Toukan1-2/+2
Prevent using uninitialized or negative index when handling steering entries. Fixes: b12d93d63c32 ('mlx4: Add support for promiscuous mode in the new steering model.') Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-nextDavid S. Miller3-2/+5
Johan Hedberg says: ==================== pull request: bluetooth-next 2016-05-14 Here are two more Bluetooth patches for the 4.7 kernel which we wanted to get into net-next before the merge window opens. Please let me know if there are any issues pulling. Thanks. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16Merge branch 'w5100-small-changes'David S. Miller3-14/+21
Akinobu Mita says: ==================== net: w5100: collection of small changes This patch series is the collection of relatively small changes for w5100 driver which includes a cleanup with no functional change, two fixes, and adding a functionality. * Changes from v1 - Remove the watchdong_timeo assignment to set default tx timeout, suggested by David Miller. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: w5100-spi: add support to specify MAC address by device treeAkinobu Mita3-4/+8
This adds support to specify the MAC address by 'mac-address' or 'local-mac-address' properties in the device tree. These are common properties for the Ethernet controller. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: w5100: increase TX timeout periodAkinobu Mita1-1/+0
This increases TX timeout period from one second to 5 seconds which is the default value if the driver doesn't explicitly set net_device->watchdog_timeo. The one second timeout is too short for W5100 with SPI interface mode which doesn't support burst READ/WRITE processing in the SPI transfer. If the packet is transmitted while RX packets are being received at a very high rate, the TX transmittion work in the workqueue is delayed and the watchdog timer is expired. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: w5100: fix MAC filtering for W5500Akinobu Mita1-4/+13
W5500 has different bit position for MAC filter in Socket n mode register from W5100 and W5200. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: w5100: remove unused is_w5200()Akinobu Mita1-5/+0
The is_w5200() function is not used anymore by the commit which adds the W5500 support. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16Merge branch 'lxt-cleanups'David S. Miller1-17/+5
Sergei Shtylyov says: ==================== Here's the set of 2 patches against DaveM's 'net-next.git' repo. We save several LoCs on the unneeded local variables.... [1/2] lxt: simplify lxt97[01]_config_intr() [2/2] lxt: simplify lxt970_config_init() ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16lxt: simplify lxt970_config_init()Sergei Shtylyov1-5/+1
This function declares the 'err' local variable for no good reason, get rid of it. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16lxt: simplify lxt97[01]_config_intr()Sergei Shtylyov1-12/+4
Both these functions declare the 'err' local variables for no good reason, get rid of them. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16Merge branch 'bpf-blinding'David S. Miller20-136/+569
Daniel Borkmann says: ==================== BPF updates This set implements constant blinding for BPF, first couple of patches are some preparatory cleanups, followed by the blinding. Please see individual patches for details. Thanks a lot! ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16bpf, s390: add support for constant blindingDaniel Borkmann1-17/+56
This patch adds recently added constant blinding helpers into the s390 eBPF JIT. In the bpf_int_jit_compile() path, requirements are to utilize bpf_jit_blind_constants()/bpf_jit_prog_release_other() pair for rewriting the program into a blinded one, and to map the BPF_REG_AX register to a CPU register. The mapping of BPF_REG_AX is at r12 and similarly like in x86 case performs reloading when ld_abs/ind is used. When blinding is not used, there's no additional overhead in the generated image. When BPF_REG_AX is used, we don't need to emit skb->data reload when helper function changed skb->data, as this will be reloaded later on anyway from stack on ld_abs/ind, where skb->data is needed. s390 allows for this w/o much additional complexity unlike f.e. x86. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16bpf, arm64: add support for constant blindingDaniel Borkmann1-12/+40
This patch adds recently added constant blinding helpers into the arm64 eBPF JIT. In the bpf_int_jit_compile() path, requirements are to utilize bpf_jit_blind_constants()/bpf_jit_prog_release_other() pair for rewriting the program into a blinded one, and to map the BPF_REG_AX register to a CPU register. The mapping is on x9. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Zi Shen Lim <zlim.lnx@gmail.com> Acked-by: Yang Shi <yang.shi@linaro.org> Tested-by: Yang Shi <yang.shi@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16bpf, x86: add support for constant blindingDaniel Borkmann1-13/+53
This patch adds recently added constant blinding helpers into the x86 eBPF JIT. In the bpf_int_jit_compile() path, requirements are to utilize bpf_jit_blind_constants()/bpf_jit_prog_release_other() pair for rewriting the program into a blinded one, and to map the BPF_REG_AX register to a CPU register. The mapping of BPF_REG_AX is at non-callee saved register r10, and thus shared with cached skb->data used for ld_abs/ind and not in every program type needed. When blinding is not used, there's zero additional overhead in the generated image. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16bpf: add generic constant blinding for use in jitsDaniel Borkmann5-2/+270
This work adds a generic facility for use from eBPF JIT compilers that allows for further hardening of JIT generated images through blinding constants. In response to the original work on BPF JIT spraying published by Keegan McAllister [1], most BPF JITs were changed to make images read-only and start at a randomized offset in the page, where the rest was filled with trap instructions. We have this nowadays in x86, arm, arm64 and s390 JIT compilers. Additionally, later work also made eBPF interpreter images read only for kernels supporting DEBUG_SET_MODULE_RONX, that is, x86, arm, arm64 and s390 archs as well currently. This is done by default for mentioned JITs when JITing is enabled. Furthermore, we had a generic and configurable constant blinding facility on our todo for quite some time now to further make spraying harder, and first implementation since around netconf 2016. We found that for systems where untrusted users can load cBPF/eBPF code where JIT is enabled, start offset randomization helps a bit to make jumps into crafted payload harder, but in case where larger programs that cross page boundary are injected, we again have some part of the program opcodes at a page start offset. With improved guessing and more reliable payload injection, chances can increase to jump into such payload. Elena Reshetova recently wrote a test case for it [2, 3]. Moreover, eBPF comes with 64 bit constants, which can leave some more room for payloads. Note that for all this, additional bugs in the kernel are still required to make the jump (and of course to guess right, to not jump into a trap) and naturally the JIT must be enabled, which is disabled by default. For helping mitigation, the general idea is to provide an option bpf_jit_harden that admins can tweak along with bpf_jit_enable, so that for cases where JIT should be enabled for performance reasons, the generated image can be further hardened with blinding constants for unpriviledged users (bpf_jit_harden == 1), with trading off performance for these, but not for privileged ones. We also added the option of blinding for all users (bpf_jit_harden == 2), which is quite helpful for testing f.e. with test_bpf.ko. There are no further e.g. hardening levels of bpf_jit_harden switch intended, rationale is to have it dead simple to use as on/off. Since this functionality would need to be duplicated over and over for JIT compilers to use, which are already complex enough, we provide a generic eBPF byte-code level based blinding implementation, which is then just transparently JITed. JIT compilers need to make only a few changes to integrate this facility and can be migrated one by one. This option is for eBPF JITs and will be used in x86, arm64, s390 without too much effort, and soon ppc64 JITs, thus that native eBPF can be blinded as well as cBPF to eBPF migrations, so that both can be covered with a single implementation. The rule for JITs is that bpf_jit_blind_constants() must be called from bpf_int_jit_compile(), and in case blinding is disabled, we follow normally with JITing the passed program. In case blinding is enabled and we fail during the process of blinding itself, we must return with the interpreter. Similarly, in case the JITing process after the blinding failed, we return normally to the interpreter with the non-blinded code. Meaning, interpreter doesn't change in any way and operates on eBPF code as usual. For doing this pre-JIT blinding step, we need to make use of a helper/auxiliary register, here BPF_REG_AX. This is strictly internal to the JIT and not in any way part of the eBPF architecture. Just like in the same way as JITs internally make use of some helper registers when emitting code, only that here the helper register is one abstraction level higher in eBPF bytecode, but nevertheless in JIT phase. That helper register is needed since f.e. manually written program can issue loads to all registers of eBPF architecture. The core concept with the additional register is: blind out all 32 and 64 bit constants by converting BPF_K based instructions into a small sequence from K_VAL into ((RND ^ K_VAL) ^ RND). Therefore, this is transformed into: BPF_REG_AX := (RND ^ K_VAL), BPF_REG_AX ^= RND, and REG <OP> BPF_REG_AX, so actual operation on the target register is translated from BPF_K into BPF_X one that is operating on BPF_REG_AX's content. During rewriting phase when blinding, RND is newly generated via prandom_u32() for each processed instruction. 64 bit loads are split into two 32 bit loads to make translation and patching not too complex. Only basic thing required by JITs is to call the helper bpf_jit_blind_constants()/bpf_jit_prog_release_other() pair, and to map BPF_REG_AX into an unused register. Small bpf_jit_disasm extract from [2] when applied to x86 JIT: echo 0 > /proc/sys/net/core/bpf_jit_harden ffffffffa034f5e9 + <x>: [...] 39: mov $0xa8909090,%eax 3e: mov $0xa8909090,%eax 43: mov $0xa8ff3148,%eax 48: mov $0xa89081b4,%eax 4d: mov $0xa8900bb0,%eax 52: mov $0xa810e0c1,%eax 57: mov $0xa8908eb4,%eax 5c: mov $0xa89020b0,%eax [...] echo 1 > /proc/sys/net/core/bpf_jit_harden ffffffffa034f1e5 + <x>: [...] 39: mov $0xe1192563,%r10d 3f: xor $0x4989b5f3,%r10d 46: mov %r10d,%eax 49: mov $0xb8296d93,%r10d 4f: xor $0x10b9fd03,%r10d 56: mov %r10d,%eax 59: mov $0x8c381146,%r10d 5f: xor $0x24c7200e,%r10d 66: mov %r10d,%eax 69: mov $0xeb2a830e,%r10d 6f: xor $0x43ba02ba,%r10d 76: mov %r10d,%eax 79: mov $0xd9730af,%r10d 7f: xor $0xa5073b1f,%r10d 86: mov %r10d,%eax 89: mov $0x9a45662b,%r10d 8f: xor $0x325586ea,%r10d 96: mov %r10d,%eax [...] As can be seen, original constants that carry payload are hidden when enabled, actual operations are transformed from constant-based to register-based ones, making jumps into constants ineffective. Above extract/example uses single BPF load instruction over and over, but of course all instructions with constants are blinded. Performance wise, JIT with blinding performs a bit slower than just JIT and faster than interpreter case. This is expected, since we still get all the performance benefits from JITing and in normal use-cases not every single instruction needs to be blinded. Summing up all 296 test cases averaged over multiple runs from test_bpf.ko suite, interpreter was 55% slower than JIT only and JIT with blinding was 8% slower than JIT only. Since there are also some extremes in the test suite, I expect for ordinary workloads that the performance for the JIT with blinding case is even closer to JIT only case, f.e. nmap test case from suite has averaged timings in ns 29 (JIT), 35 (+ blinding), and 151 (interpreter). BPF test suite, seccomp test suite, eBPF sample code and various bigger networking eBPF programs have been tested with this and were running fine. For testing purposes, I also adapted interpreter and redirected blinded eBPF image to interpreter and also here all tests pass. [1] http://mainisusuallyafunction.blogspot.com/2012/11/attacking-hardened-linux-systems-with.html [2] https://github.com/01org/jit-spray-poc-for-ksp/ [3] http://www.openwall.com/lists/kernel-hardening/2016/05/03/5 Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Elena Reshetova <elena.reshetova@intel.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16bpf: prepare bpf_int_jit_compile/bpf_prog_select_runtime apisDaniel Borkmann8-18/+40
Since the blinding is strictly only called from inside eBPF JITs, we need to change signatures for bpf_int_jit_compile() and bpf_prog_select_runtime() first in order to prepare that the eBPF program we're dealing with can change underneath. Hence, for call sites, we need to return the latest prog. No functional change in this patch. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16bpf: add bpf_patch_insn_single helperDaniel Borkmann3-44/+83
Move the functionality to patch instructions out of the verifier code and into the core as the new bpf_patch_insn_single() helper will be needed later on for blinding as well. No changes in functionality. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16bpf, x86/arm64: remove useless checks on progDaniel Borkmann2-6/+0
There is never such a situation, where bpf_int_jit_compile() is called with either prog as NULL or len as 0, so the tests are unnecessary and confusing as people would just copy them. s390 doesn't have them, so no change is needed there. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16bpf: split HAVE_BPF_JIT into cBPF and eBPF variantDaniel Borkmann8-10/+18
Split the HAVE_BPF_JIT into two for distinguishing cBPF and eBPF JITs. Current cBPF ones: # git grep -n HAVE_CBPF_JIT arch/ arch/arm/Kconfig:44: select HAVE_CBPF_JIT arch/mips/Kconfig:18: select HAVE_CBPF_JIT if !CPU_MICROMIPS arch/powerpc/Kconfig:129: select HAVE_CBPF_JIT arch/sparc/Kconfig:35: select HAVE_CBPF_JIT Current eBPF ones: # git grep -n HAVE_EBPF_JIT arch/ arch/arm64/Kconfig:61: select HAVE_EBPF_JIT arch/s390/Kconfig:126: select HAVE_EBPF_JIT if PACK_STACK && HAVE_MARCH_Z196_FEATURES arch/x86/Kconfig:94: select HAVE_EBPF_JIT if X86_64 Later code also needs this facility to check for eBPF JITs. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16bpf: move bpf_jit_enable declarationDaniel Borkmann2-1/+2
Move the bpf_jit_enable declaration to the filter.h file where most other core code is declared, also since we're going to add a second knob there. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16bpf: minor cleanups in ebpf codeDaniel Borkmann2-21/+15
Besides others, remove redundant comments where the code is self documenting enough, and properly indent various bpf_verifier_ops and bpf_prog_type_list declarations. Moreover, remove two exports that actually have no module user. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: dsa: mv88e6xxx: remove bridge workVivien Didelot2-34/+8
Now that the bridge code defers the switchdev port state setting, there is no need to defer the port STP state change within the mv88e6xxx code. Thus get rid of the driver's bridge work code. This also fixes a race condition where the DSA layer assumes that the bridge code already set the unbridged port's STP state to Disabled before restoring the Forwarding state. As a consequence, this also fixes the FDB flush for the unbridged port which now correctly occurs during the Forwarding to Disabled transition. Fixes: 0bc05d585d38 ("switchdev: allow caller to explicitly request attr_set as deferred") Reported-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.