aboutsummaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2015-12-11ieee802154/adf7242: Driver for ADF7242 MAC IEEE802154Michael Hennerich5-0/+1324
This driver has been sitting in the linux-zigbee[2] repository for a long time. We updated it from time to time and made it available via our github kernel repository. The Linux MAC802.15.4 support has improved a lot since then. Thanks to all! So it’s finally time to upstream this driver. The ADF7242 requires an add-on firmware for the automatic IEEE 802.15.4 operating modes. The firmware file is currently made available on the ADF7242 wiki page here [1] [1] http://wiki.analog.com/resources/tools-software/linux-drivers/networking-mac802154/adf7242 [2] http://sourceforge.net/p/linux-zigbee/kernel/ci/devel/tree/drivers/ieee802154/adf7242.c Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-11Bluetooth: Do not filter multicast addresses by defaultDanny Schweizer1-2/+5
A Linux PC is connected with another device over Bluetooth PAN using a BNEP interface. Whenever a packet is tried to be sent over the BNEP interface, the function "bnep_net_xmit()" in "net/bluetooth/bnep/netdev.c" is called. This function calls "bnep_net_mc_filter()", which checks (if the destination address is multicast) if the address is set in a certain multicast filter (&s->mc_filter). If it is not, then it is not sent out. This filter is only changed in two other functions, found in net/bluetooth/bnep/core.c": in "bnep_ctrl_set_mc_filter()", which is only called if a message of type "BNEP_FILTER_MULTI_ADDR_SET" is received. Otherwise, it is set in "bnep_add_connection()", where it is set to a default value which only adds the broadcast address to the filter: set_bit(bnep_mc_hash(dev->broadcast), (ulong *) &s->mc_filter); To sum up, if the BNEP interface does not receive any message of type "BNEP_FILTER_MULTI_ADDR_SET", it will not send out any messages with multicast destination addresses except for broadcast. However, in the BNEP specification (page 27 in http://grouper.ieee.org/groups/802/15/Bluetooth/BNEP.pdf), it is said that per default, all multicast addresses should not be filtered, i.e. the BNEP interface should be able to send packets with any multicast destination address. It seems that the default case is wrong: the multicast filter should not block almost all multicast addresses, but should not filter out any. This leads to the problem that e.g. Neighbor Solicitation messages sent with Bluetooth PAN over the BNEP interface to a multicast destination address other than broadcast are blocked and not sent out. Therefore, in the default case, we set the mc_filter to ~0LL to not filter out any multicast addresses. Signed-off-by: Danny Schweizer <danny.schweizer@proofnet.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-11ieee802154-atusb: Delete an unnecessary check before the function call "kfree_skb"Markus Elfring1-2/+1
The kfree_skb() function tests whether its argument is NULL and then returns immediately. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Acked-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: h5: Do not initialize Configuration fieldAndrei Emeltchenko1-2/+2
Initializing Configuration field in H5 Config message to 0x01 gives wrong impression that the value is used and needed. Later on the whole field is rewritten with h5_cfg_field(). Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10mac802154: tx: fix synced xmit deadlockAlexander Aring2-12/+0
This patch reverts 6001d52 ("mac802154: tx: don't allow if down while sync tx"). This has side effects with stop callback which flush the transmit workqueue. The stop callback will wait until the workqueue is flushed and holding the rtnl lock. That means it can happen that the stop callback waits forever because it try to lock the rtnl mutex which is already hold by stop callback. Cc: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10ipv6: add ipv6_addr_prefix_copyAlexander Aring1-0/+15
This patch adds a static inline function ipv6_addr_prefix_copy which copies a ipv6 address prefix(argument pfx) into the ipv6 address prefix. The prefix len is given by plen as bits. This function mainly based on ipv6_addr_prefix which copies one address prefix from address into a new ipv6 address destination and zero all other address bits. The difference is that ipv6_addr_prefix_copy don't get a prefix from an ipv6 address, it sets a prefix to an ipv6 address with keeping other address bits. The use case is for context based address compression inside 6LoWPAN IPHC header which keeping ipv6 prefixes inside a context table to lookup address-bits without sending them. Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Acked-by: Łukasz Duda <lukasz.duda@nordicsemi.no> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Acked-by: David S. Miller <davem@davemloft.net> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-106lowpan: add debugfs supportAlexander Aring6-1/+120
This patch will introduce a 6lowpan entry into the debugfs if enabled. Inside this 6lowpan directory we create a subdirectories of all 6lowpan interfaces to offer a per interface debugfs support. Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-106lowpan: add lowpan dev register helpersAlexander Aring4-12/+42
This patch introduces register and unregister functionality for lowpan interfaces. While register a lowpan interface there are several things which need to be initialize by the 6lowpan subsystem. Upcoming functionality need to register/unregister per interface components e.g. debugfs entry. Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-106lowpan: add nhc module for GHC routing extension header detectionStefan Schmidt3-0/+34
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-106lowpan: add nhc module for GHC fragmentation extension header detectionStefan Schmidt3-0/+35
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-106lowpan: add nhc module for GHC destination extension header detectionStefan Schmidt3-0/+34
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-106lowpan: add nhc module for GHC ICMPv6 detectionStefan Schmidt3-0/+33
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-106lowpan: add nhc module for GHC UDP detectionStefan Schmidt3-0/+33
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-106lowpan: add nhc module for GHC hop-by-hopextension header detectionStefan Schmidt3-0/+36
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-106lowpan: clarify Kconfig entries for upcoming GHC supportStefan Schmidt1-2/+3
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: btintel: Create common Intel Version Read functionLoic Poulain4-92/+66
The Intel Version Read command is used to retrieve information about hardware and firmware version/revision of Intel Bluetooth controllers. This is an Intel generic command used in USB and UART drivers. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Fix locking in bt_accept_dequeue after disconnectionYichen Zhao1-1/+1
Fix a crash that may happen when bt_accept_dequeue is run after a Bluetooth connection has been disconnected. bt_accept_unlink was called after release_sock, permitting bt_accept_unlink to run twice on the same socket and cause a NULL pointer dereference. [50510.241632] BUG: unable to handle kernel NULL pointer dereference at 00000000000001a8 [50510.241694] IP: [<ffffffffc01243f7>] bt_accept_unlink+0x47/0xa0 [bluetooth] [50510.241759] PGD 0 [50510.241776] Oops: 0002 [#1] SMP [50510.241802] Modules linked in: rtl8192cu rtl_usb rtlwifi rtl8192c_common 8021q garp stp mrp llc rfcomm bnep nls_iso8859_1 intel_rapl x86_pkg_temp_thermal intel_powerclamp coretemp arc4 ath9k ath9k_common ath9k_hw ath kvm eeepc_wmi asus_wmi mac80211 snd_hda_codec_hdmi snd_hda_codec_realtek sparse_keymap crct10dif_pclmul snd_hda_codec_generic crc32_pclmul snd_hda_intel snd_hda_controller cfg80211 snd_hda_codec i915 snd_hwdep snd_pcm ghash_clmulni_intel snd_timer snd soundcore serio_raw cryptd drm_kms_helper drm i2c_algo_bit shpchp ath3k mei_me lpc_ich btusb bluetooth 6lowpan_iphc mei lp parport wmi video mac_hid psmouse ahci libahci r8169 mii [50510.242279] CPU: 0 PID: 934 Comm: krfcommd Not tainted 3.16.0-49-generic #65~14.04.1-Ubuntu [50510.242327] Hardware name: ASUSTeK Computer INC. VM40B/VM40B, BIOS 1501 12/09/2014 [50510.242370] task: ffff8800d9068a30 ti: ffff8800d7a54000 task.ti: ffff8800d7a54000 [50510.242413] RIP: 0010:[<ffffffffc01243f7>] [<ffffffffc01243f7>] bt_accept_unlink+0x47/0xa0 [bluetooth] [50510.242480] RSP: 0018:ffff8800d7a57d58 EFLAGS: 00010246 [50510.242511] RAX: 0000000000000000 RBX: ffff880119bb8c00 RCX: ffff880119bb8eb0 [50510.242552] RDX: ffff880119bb8eb0 RSI: 00000000fffffe01 RDI: ffff880119bb8c00 [50510.242592] RBP: ffff8800d7a57d60 R08: 0000000000000283 R09: 0000000000000001 [50510.242633] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800d8da9eb0 [50510.242673] R13: ffff8800d74fdb80 R14: ffff880119bb8c00 R15: ffff8800d8da9c00 [50510.242715] FS: 0000000000000000(0000) GS:ffff88011fa00000(0000) knlGS:0000000000000000 [50510.242761] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [50510.242794] CR2: 00000000000001a8 CR3: 0000000001c13000 CR4: 00000000001407f0 [50510.242835] Stack: [50510.242849] ffff880119bb8eb0 ffff8800d7a57da0 ffffffffc0124506 ffff8800d8da9eb0 [50510.242899] ffff8800d8da9c00 ffff8800d9068a30 0000000000000000 ffff8800d74fdb80 [50510.242949] ffff8800d6f85208 ffff8800d7a57e08 ffffffffc0159985 000000000000001f [50510.242999] Call Trace: [50510.243027] [<ffffffffc0124506>] bt_accept_dequeue+0xb6/0x180 [bluetooth] [50510.243085] [<ffffffffc0159985>] l2cap_sock_accept+0x125/0x220 [bluetooth] [50510.243128] [<ffffffff810a1b30>] ? wake_up_state+0x20/0x20 [50510.243163] [<ffffffff8164946e>] kernel_accept+0x4e/0xa0 [50510.243200] [<ffffffffc05b97cd>] rfcomm_run+0x1ad/0x890 [rfcomm] [50510.243238] [<ffffffffc05b9620>] ? rfcomm_process_rx+0x8a0/0x8a0 [rfcomm] [50510.243281] [<ffffffff81091572>] kthread+0xd2/0xf0 [50510.243312] [<ffffffff810914a0>] ? kthread_create_on_node+0x1c0/0x1c0 [50510.243353] [<ffffffff8176e9d8>] ret_from_fork+0x58/0x90 [50510.243387] [<ffffffff810914a0>] ? kthread_create_on_node+0x1c0/0x1c0 [50510.243424] Code: 00 48 8b 93 b8 02 00 00 48 8d 83 b0 02 00 00 48 89 51 08 48 89 0a 48 89 83 b0 02 00 00 48 89 83 b8 02 00 00 48 8b 83 c0 02 00 00 <66> 83 a8 a8 01 00 00 01 48 c7 83 c0 02 00 00 00 00 00 00 f0 ff [50510.243685] RIP [<ffffffffc01243f7>] bt_accept_unlink+0x47/0xa0 [bluetooth] [50510.243737] RSP <ffff8800d7a57d58> [50510.243758] CR2: 00000000000001a8 [50510.249457] ---[ end trace bb984f932c4e3ab3 ]--- Signed-off-by: Yichen Zhao <zhaoyichen@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Don't treat connection timeout as a failureJohan Hedberg1-2/+10
When we're doing background scanning and connection attempts it's possible we timeout trying to connect and go back to scanning again. The timeout triggers a HCI_LE_Create_Connection_Cancel which will trigger a Connection Complete with "Unknown Connection Identifier" error status. Since we go back to scanning this isn't really a failure and shouldn't be presented as such to user space through mgmt. The exception to this is if the connection attempt was due to an explicit request on an L2CAP socket (indicated by params->explicit_connect being true). Since the socket will get an error it's consistent to also notify the failure on mgmt in this case. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Use continuous scanning when creating LE connectionsJohan Hedberg1-1/+5
All LE connections are now triggered through a preceding passive scan and waiting for a connectable advertising report. This means we've got the best possible guarantee that the device is within range and should be able to request the controller to perform continuous scanning. This way we minimize the risk that we miss out on any advertising packets. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org # 4.3+
2015-12-10Bluetooth: btintel: Add manufacturing enter/exit helpersLoic Poulain3-94/+86
Older Intel controllers need to enter manufacturing mode to perform some vendor specific operations (patching, configuration...). Add enter/exit manufaturing methods and refactor existing manufacturing code. Exit can be configured to perform a reset. Reset can be performed either with patches activated or deactivated. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Add support of Toshiba Broadcom based devicesDmitry Tunin1-0/+4
BugLink: https://bugs.launchpad.net/bugs/1522949 T: Bus=03 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0930 ProdID=0225 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM43142A0 S: SerialNumber=4CBB58034671 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
2015-12-10Bluetooth: hci_intel: Use shorter timeout for HCI commandsLoic Poulain1-4/+4
Use the standard HCI_CMD_TIMEOUT(1s) for HCI command instead of HCI_INIT_TIMEOUT(10s) which is not justified in these cases. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: hci_ldisc: Remove dead codePeter Hurley1-7/+1
The N_HCI ldisc does not define a flush_buffer() ldisc method, so the check when opening the ldisc is always false. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Clean up current advertising instance trackingJohan Hedberg4-66/+32
We can simplify a lot of code by making sure hdev->cur_adv_instance is always up-to-date. This allows e.g. the removal of the get_current_adv_instance() helper function and the special HCI_ADV_CURRENT value. This patch also makes selecting instance 0x00 explicit in the various calls where advertising instances aren't enabled, e.g. when HCI_ADVERTISING is set or we've just finished enabling LE. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Clean up advertising initialization in powered_update_hci()Johan Hedberg1-18/+12
The logic in powered_update_hci() to initialize the advertising data & state is a bit more complicated than it needs to be. It was previously not doing anything if HCI_LE_ENABLED wasn't set, but this was not obvious by quickly looking at the code. Now the conditions for the various actions are more explicit. Another simplification is due to the fact that __hci_req_schedule_adv_instance() takes care of setting hdev->cur_adv_instance so there's no need to set it before calling the function. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Remove redundant check for req.cmd_qJohan Hedberg1-2/+1
The hci_req_run() function already checks for empty cmd_q and bails out if necessary. Also, req.cmd_q should really be treated as private data of the request and not accessed directly. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Fix updating wrong instance's scan_rsp dataJohan Hedberg1-1/+1
The __hci_req_update_scan_rsp_data gets the instance to be updated which should get passed to update_inst_scan_rsp_data() instead of always enabling the current instance. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Simplify setting Configuration FieldAndrei Emeltchenko1-5/+1
Only Sliding Window Size is used at the moment for H5 Bluetooth Configuration messages. Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Use hexadecimal notation for maskAndrei Emeltchenko1-1/+1
Using hexadecimal notation for mask makes code easier to read Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Remove unnecessary HCI_ADVERTISING_INSTANCE flagJohan Hedberg3-19/+9
This flag just tells us whether hdev->adv_instances is empty or not. We can equally well use the list_empty() function to get this information. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Simplify read_adv_features codeJohan Hedberg1-20/+8
The code in the Read Advertising Features mgmt command handler is unnecessarily complicated. Clean it up and remove unnecessary variables & branches. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Perform HCI update for power on synchronouslyJohan Hedberg5-134/+128
The request to update HCI during power on is always coming either from hdev->req_workqueue or through an ioctl, so it's safe to use hci_req_sync for it. This way we also eliminate potential races with incoming mgmt commands or other actions while powering on. Part of this refactoring is the splitting of mgmt_powered() into mgmt_power_on() and __mgmt_power_off() functions. The main reason is the different requirements as far as hdev locking is concerned, as highlighted with the __ prefix of the power off API. Since the power on in the case of clearing the AUTO_OFF flag cannot be done synchronously in the set_powered mgmt handler, the hci_power_on work callback is extended to cover this (which also simplifies the set_powered helper a lot). Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Move fast connectable code to hci_request.cJohan Hedberg3-39/+40
We'll soon need this both in hci_request.c and mgmt.c so move it to hci_request.c as a generic helper. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Move EIR update to hci_request.cJohan Hedberg3-195/+198
We'll soon need to update the EIR both from hci_request.c and mgmt.c so move update_eir() as a more generic request helper to hci_request.c. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: HCI name update to hci_request.cJohan Hedberg3-12/+14
We'll soon need this both from hci_request.c and mgmt.c so move it as a request helper function to hci_request.c. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Move discoverable timeout behind hdev->req_workqueueJohan Hedberg4-53/+28
Since the other discoverable changes are behind req_workqueue now it only makes sense to move the discoverable timeout there as well. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Move discoverable changes to hdev->req_workqueueJohan Hedberg3-77/+79
The discoverable mode is intrinsically linked with the connectable mode e.g. through sharing the same HCI command (Write Scan Enable) for BR/EDR. It makes therefore sense to move it to hci_request.c and run the changes through the same hdev->req_workqueue. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Perform Class of Device changes through hdev->req_workqueueJohan Hedberg3-47/+49
The Class of Device needs to be changed e.g. for limited discoverable mode. In preparation of moving the discoverable mode to hci_request.c and hdev->req_workqueue, move the Class of Device helpers there first. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Move connectable changes to hdev->req_workqueueJohan Hedberg3-74/+53
This way the connectable changes are synchronized against each other, which helps avoid potential races. The connectable mode is also linked together with LE advertising which makes is more convenient to have it behind the same workqueue. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Move advertising instance management to hci_request.cJohan Hedberg7-566/+589
This paves the way for eventually performing advertising changes through the hdev->req_workqueue. Some new APIs need to be exposed from mgmt.c to hci_request.c and vice-versa, but many of them will go away once hdev->req_workqueue gets used. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Move __hci_update_background_scan up in hci_request.cJohan Hedberg1-73/+73
This way we avoid the need to do a forward declaration in later patches. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10Bluetooth: Run page scan updates through hdev->req_workqueueJohan Hedberg5-21/+35
Since Add/Remove Device perform the page scan updates independently from the HCI command completion we've introduced a potential race when multiple mgmt commands are queued. Doing the page scan updates through the req_workqueue ensures that the state changes are performed in a race-free manner. At the same time, to make the request helper more widely usable, extend it to also cover Inquiry Scan changes since those are behind the same HCI command. This is also reflected in the new name of the API as well as the work struct name. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-09cgroup: fix sock_cgroup_data initialization on earlier compilersTejun Heo1-2/+2
sock_cgroup_data is a struct containing an anonymous union. sock_cgroup_set_prioidx() and sock_cgroup_set_classid() were initializing a field inside the anonymous union as follows. struct sock_ccgroup_data skcd_buf = { .val = VAL }; While this is fine on more recent compilers, gcc-4.4.7 triggers the following errors. include/linux/cgroup-defs.h: In function ‘sock_cgroup_set_prioidx’: include/linux/cgroup-defs.h:619: error: unknown field ‘val’ specified in initializer include/linux/cgroup-defs.h:619: warning: missing braces around initializer include/linux/cgroup-defs.h:619: warning: (near initialization for ‘skcd_buf.<anonymous>’) This is because .val belongs to the anonymous union nested inside the struct but the initializer is missing the nesting. Fix it by adding an extra pair of braces. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Alaa Hleihel <alaa@dev.mellanox.co.il> Fixes: bd1060a1d671 ("sock, cgroup: add sock->sk_cgroup") Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-08chelsio: constify cmac_ops structuresJulia Lawall2-2/+2
The cmac_ops structures are never modified, so declare them as const. Done with the help of Coccinelle. Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-08bnx2x: remove rx_pkt/rx_callsEric Dumazet2-6/+0
These fields are updated but never read. Remove the overhead. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-08bnx2x: avoid soft lockup in bnx2x_poll()Eric Dumazet1-30/+21
Under heavy TX load, bnx2x_poll() can loop forever and trigger soft lockup bugs. A napi poll handler must yield after one TX completion round, risk of livelock is too high otherwise. Bug is very easy to trigger using a debug build, and udp flood, because of added cpu cycles in TX completion, and we do not receive enough packets to break the loop. Reported-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ariel Elior <ariel.elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-08rhashtable: Remove unnecessary wmb for future_tblHerbert Xu1-3/+0
The patch 9497df88ab5567daa001829051c5f87161a81ff0 ("rhashtable: Fix reader/rehash race") added a pair of barriers. In fact the wmb is superfluous because every subsequent write to the old or new hash table uses rcu_assign_pointer, which itself carriers a full barrier prior to the assignment. Therefore we may remove the explicit wmb. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-08Merge branch 'cxgb4-update-kconfig-and-fixes'David S. Miller6-93/+202
Hariprasad Shenai says: ==================== Update Kconfig and some fixes for cxgb4 This series update Kconfig to add description for Chelsio's next generation T6 family of adapters, also fixes ethtool stats alignment and prevents simultaneous execution of service_ofldq thread, deals with queue wrap around and adds some fl counters for debugging purpose and device ID for new T5 adapters. This patch series has been created against net-next tree and includes patches on cxgb4 driver. We have included all the maintainers of respective drivers. Kindly review the change and let us know in case of any review comments. Thanks V2: Declare 'service_ofldq_running' as bool in Patch 4/7 ("cxgb4: prevent simultaneous execution of service_ofldq()") based on review comment by David Miller ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-08cxgb4: Adds PCI device id for new T5 adaptersHariprasad Shenai1-0/+3
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-08cxgb4: Add FL DMA mapping error and low counterHariprasad Shenai3-0/+11
Add Free List DMA Mapping Errors to SGE Queue info for Free Lists. Add Free List "Low" counter to count the number of times we see the number of pointers that we _think_ the hardware sees in the Free List below the Egress Threshold. Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.