| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Device support 64 bit dma mask.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Window register is not per pci-func, so caching can
result in expected result.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MSI_MODE, CAPABILITIES_FW and SCRATCHPAD registers are obsolete.
Driver should not use them.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before going for recovery, every pci-func should check fw state,
irrespective of device state. This to avoid unnecssary sending
of command for ctx destroy.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Version 1.28
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocating memory can fail, and since we have the memory we need
in sky2_resume when sky2_suspend is called, just stop the hardware
without freeing the memory it's using.
This avoids the possibility of failing because we can't allocate
memory in sky2_resume(), and allows sharing code with sky2_restart().
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code to bring down all sky2 interfaces and bring it up
again can be reused in sky2_suspend and sky2_resume.
Factor the code to bring the interfaces down into
sky2_all_down and the up code into sky2_all_up.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Interrupts should be masked, then synchronized, and
finally NAPI should be disabled.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_stop_queue does not ensure all in-progress transmits are complete,
so use netif_tx_disable() instead.
Secondly, make sure NAPI polls are disabled before stopping the tx queue,
otherwise sky2_status_intr might trigger a TX queue wakeup between when
we stop the queue and NAPI is disabled.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Multicast settings will be lost on reset, so restore them.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There appears to be an off-by-1 defect in the maximum packet size
copied when copybreak is speified in these modules.
The copybreak module params are specified as:
"Maximum size of packet that is copied to a new buffer on receive"
The tests are changed from "< copybreak" to "<= copybreak"
and moved into new static functions for readability.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During the cleanup pass after the removal of e1000e hardware from e1000 some
parameters were missed. Remove them because it is just dead code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When adding more than 14 mac-vlan adapters on e1000 the driver
would fire a WARN_ON when adding the 15th. The WARN_ON in this
case is completely un-necessary, as the code below the WARN_ON is
directly handling the value the WARN_ON triggered on.
CC: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the following MAC functions are moved from 82598 & 82599 specific
hardware files to common.[ch] to accommodate new silicon changes. Also
fixed some white space issues
* get_san_mac_addr, check_link, set_vmdq, clear_vmdq, clear_vfta,
* set_vfta, fc_enable, init_uta_tables
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't use zero magic "bad" value to check if IXGBE_RSC_CB(skb)->dma
is valid. It is only valid in x86/arm/m68k/alpha architectures and in
spark, powerPC and other architectures it should be ~0. As per
Benjamin Herrenschmidt feedback use a bool flag to decide if
the packet unmapping is delayed in hardware RSC till EOP is reached
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce uc_set_promisc flag to fix enabling of promisc mode
when exceeding the number of supported RAR entries.
Issue discovered by Ben Greear when using mac-vlans.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
This patch removes from net/ netfilter files
all the unnecessary return; statements that precede the
last closing brace of void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
Signed-off-by: Joe Perches <joe@perches.com>
[Patrick: changed to keep return statements in otherwise empty function bodies]
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
Make sure all printk messages have a severity level.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
Change netfilter asserts to standard WARN_ON. This has the
benefit of backtrace info and also causes netfilter errors
to show up on kerneloops.org.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
[ 4593.956206] BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
[ 4593.956219] IP: [<ffffffffa03357a4>] br_nf_forward_finish+0x154/0x170 [bridge]
[ 4593.956232] PGD 195ece067 PUD 1ba005067 PMD 0
[ 4593.956241] Oops: 0000 [#1] SMP
[ 4593.956248] last sysfs file:
/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:08/ATK0110:00/hwmon/hwmon0/temp2_label
[ 4593.956253] CPU 3
...
[ 4593.956380] Pid: 29512, comm: kvm Not tainted 2.6.34-rc7-net #195 P6T DELUXE/System Product Name
[ 4593.956384] RIP: 0010:[<ffffffffa03357a4>] [<ffffffffa03357a4>] br_nf_forward_finish+0x154/0x170 [bridge]
[ 4593.956395] RSP: 0018:ffff880001e63b78 EFLAGS: 00010246
[ 4593.956399] RAX: 0000000000000608 RBX: ffff880057181700 RCX: ffff8801b813d000
[ 4593.956402] RDX: 0000000000000000 RSI: 0000000000000002 RDI: ffff880057181700
[ 4593.956406] RBP: ffff880001e63ba8 R08: ffff8801b9d97000 R09: ffffffffa0335650
[ 4593.956410] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8801b813d000
[ 4593.956413] R13: ffffffff81ab3940 R14: ffff880057181700 R15: 0000000000000002
[ 4593.956418] FS: 00007fc40d380710(0000) GS:ffff880001e60000(0000) knlGS:0000000000000000
[ 4593.956422] CS: 0010 DS: 002b ES: 002b CR0: 000000008005003b
[ 4593.956426] CR2: 0000000000000018 CR3: 00000001ba1d7000 CR4: 00000000000026e0
[ 4593.956429] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 4593.956433] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 4593.956437] Process kvm (pid: 29512, threadinfo ffff8801ba566000, task ffff8801b8003870)
[ 4593.956441] Stack:
[ 4593.956443] 0000000100000020 ffff880001e63ba0 ffff880001e63ba0 ffff880057181700
[ 4593.956451] <0> ffffffffa0335650 ffffffff81ab3940 ffff880001e63bd8 ffffffffa03350e6
[ 4593.956462] <0> ffff880001e63c40 000000000000024d ffff880057181700 0000000080000000
[ 4593.956474] Call Trace:
[ 4593.956478] <IRQ>
[ 4593.956488] [<ffffffffa0335650>] ? br_nf_forward_finish+0x0/0x170 [bridge]
[ 4593.956496] [<ffffffffa03350e6>] NF_HOOK_THRESH+0x56/0x60 [bridge]
[ 4593.956504] [<ffffffffa0335282>] br_nf_forward_arp+0x112/0x120 [bridge]
[ 4593.956511] [<ffffffff813f7184>] nf_iterate+0x64/0xa0
[ 4593.956519] [<ffffffffa032f920>] ? br_forward_finish+0x0/0x60 [bridge]
[ 4593.956524] [<ffffffff813f722c>] nf_hook_slow+0x6c/0x100
[ 4593.956531] [<ffffffffa032f920>] ? br_forward_finish+0x0/0x60 [bridge]
[ 4593.956538] [<ffffffffa032f800>] ? __br_forward+0x0/0xc0 [bridge]
[ 4593.956545] [<ffffffffa032f86d>] __br_forward+0x6d/0xc0 [bridge]
[ 4593.956550] [<ffffffff813c5d8e>] ? skb_clone+0x3e/0x70
[ 4593.956557] [<ffffffffa032f462>] deliver_clone+0x32/0x60 [bridge]
[ 4593.956564] [<ffffffffa032f6b6>] br_flood+0xa6/0xe0 [bridge]
[ 4593.956571] [<ffffffffa032f800>] ? __br_forward+0x0/0xc0 [bridge]
Don't call nf_bridge_update_protocol() for ARP traffic as skb->nf_bridge isn't
used in the ARP case.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report the PCIe link speed (2.5 or 5 Gbps).
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW VLAN extraction needs to be configured through FW to work correctly in
virtualization environments. Remove the direct register manipulation and
rely on FW.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
i) Fixes a bug where e1000_sw_lcd_config_ich8lan() was calling
e1000_lan_init_done_ich8lan() to poll the STATUS.LAN_INIT_DONE bit to
make sure the MAC had completed the PHY configuration. However,
e1000_lan_init_done_ich8lan() had already been called in one of the two
places where PHY reset occurs for ICHx/PCHx parts, which caused the second
call to busy-wait for 150 msec because the LAN_INIT_DONE bit had already
been checked and cleared.
ii) Cleanup the two separate PHY reset code paths, i.e. the full-chip reset
in e1000_reset_hw_ich8lan() and the PHY-only reset in
e1000_phy_hw_reset_ich8lan(). There was duplicate code in both paths to be
performed post-reset that are now combined into one new function -
e1000_post_phy_reset_ich8lan(). This cleanup also included moving the
clearing of the PHY Reset Asserted bit in the STATUS register (now done for
all ICH/PCH parts) and the check for the indication from h/w that basic
configuration has completed back to where it previously was in
e1000_get_cfg_done_ich8lan().
iii) Corrected a few comments
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flow control refresh timer value needs to be saved off so that it can
be programmed into the approrpiate register when applicable but without a
reset, e.g. when changing flow control parameters via ethtool.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mac->arc_subsystem was being incorrectly used to flag whether or not
manageability was enabled when it should only be used to state whether the
ARC (Host interface) subsystem is available on a particular MAC _and_ only
valid when any manageability is enabled. The ARC subsystem is currently
only available on 80003es2lan and 82573 parts supported by the driver.
A new flag, has_fwsm, is introduced to be used when checking if
manageability is enabled but only on parts that acutally have an FWSM
register. While the above parts have an FWSM register, there are other
parts that have FWSM but do not have support for the ARC subsystem,
namely 82571/2 and ICHx/PCH.
And then there are parts that have manageability, but do not have either
FWSM register or support for the ARC subsystem - these are 82574 and 82583.
For 80003es2lan, 82571/2/3 and ICH/PCH parts, this patch makes no
functional changes, it only corrects the usage of the manageability flags.
For 82574 and 82583, it fixes the incorrect accesses of the non-existent
FWSM register and ARC subsystem as well as corrects the check for
management pass-through.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The force_speed_duplex function pointer was incorrectly set. Instead of
calling the 82577-specific version it was calling the m88 version which,
among other incorrect things, reset the PHY causing autonegotiation to be
re-enabled in the PHY resulting in the link defaulting to half-duplex.
The 82577-specific force_speed_duplex function also had an issue where
it disabled Auto-MDI-X which caused the link to not come up.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After every reset all ICH/PCH parts call this function which acquires the
swflag, performs a workaround on applicable parts and releases the swflag.
There is no reason for parts for which this workaround is not applicable
to acquire and release the swflag so the function should just return
without doing anything for these parts. This also provides for the
indentation of most of the function contents to be shifted left cleaning up
the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patch addresses issues when manageability passthrough is enabled, but the
MAC_ADDR_FILTER bit is not set in the MANC register.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
...in e1000_update_nvm_checksum_ich8lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In MSI-X mode when an IMPI SoL session was active (i.e. the PHY reset was
blocked), the LSC interrupt generated by s/w to start the watchdog which
started the transmitter was not getting fired by the hardware because bit
24 (the 'other' cause bit) also needed to be set. Without an active SoL
session, the PHY was reset which caused the h/w to fire the LSC interrupt.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
82574/82583 uses different registers/bits to setup manageability filters
than all other parts supported by e1000e; set them accordingly for IPMI
pass-through. Rename the function to better reflect what it does.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running ethtool online diagnostics with no open interface, there is a
short period of time where the driver relinquishes control of the adapter
during which time AMT (manageability firmware) can put the adapter into an
unknown state resulting in such things as link test failure, hardware hang,
reporting an incorrect link speed, etc. Resetting the adapter during an
open() resolves this by putting the adapter into a quiescent state.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A couple stack cleanups missed in an earlier patch from Jesse.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Check the access by tools for hardware queue engine and handle it
separately than other block registers, otherwise incorrect data
is returned.
Support for only NX3031 based cards.
Acked-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unnecessary remap of the region in bar 0 to access onhip memory
for NX3031.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NX3031 have 64bit on card memory. Fix the limit check to
64MB and remove unnecessary 128bit read/write check.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o For NX3031, MSI_MODE, CAPABILITIES_FW and SCRATCHPAD registers
are obsolete. These register addresses can be used for different
purpose.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert tipc_msg_* inline routines that are more than one line into
standard functions, thereby eliminating some repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert buf_acquire inline routine that is more than one line into
a standard function, thereby eliminating some repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert bearer congestion inline routine that is more than one line into
a standard function, thereby eliminating some repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Converts port list inline routines that are more than one line into
standard functions, thereby eliminating a significant amount of
repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Converts nmap inline routines that are more than one line into standard
functions, thereby eliminating a significant amount of repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert address-related inline routines that are more than one
line into standard functions, thereby eliminating a significant
amount of repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These functions have enough code in them such that they
seem like sensible targets for un-inlining. Prior to doing
that, this adds the tipc_ prefix to the functions, so that
in the event of a panic dump or similar, the subsystem from
which the functions come from is immediately clear.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than live in link.c where they can only be used in that file alone,
these helper routines are better served by being in link.h
Relocated are the following:
link_working_working
link_working_unknown
link_reset_unknown
link_reset_reset
link_blocked
link_congested
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Amit Kumar Salecha
stephen hemminger
Mike McCormack
Joe Perches
Jesse Brandeburg
Mallikarjuna R Chilakala
Emil Tantilov
David S. Miller
Bart De Schuymer
Dimitris Michailidis
Bruce Allan
Sucheta Chakraborty
Allan Stephens