| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Parse TLV containing a bitmask of supported crypto operations.
The TLV contains a capability bitmask (supported operations)
and enabled bitmask. Each operation describes the crypto
protocol quite exhaustively (protocol, AEAD, direction).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW may prefer to handle some communication via a mailbox
or the vNIC may simply not have a control queue (VFs).
Add a way of exchanging ccm-compatible messages via a
mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Parse the mailbox TLV. When control message queue is not available
we can fall back to passing the control messages via the vNIC
mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We will need to release the bar lock from a workqueue
so move from a mutex to a semaphore. This lock should
not be too hot. Unfortunately semaphores don't have
lockdep support.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently if we need to modify the head of the skb and allocation
fails we would free the skb and not increment the error counter.
Make sure all errors are counted.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add 1000BaseX to the link modes which are detected based on the
MII_ESTATUS register as per 802.3 Clause 22. This allows PHYs which
support 1000BaseX to work properly with drivers using phylink.
Previously 1000BaseX support was not detected, and if that was the only
mode the PHY indicated support for, phylink would refuse to attach it
due to the list of supported modes being empty.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull parisc fixes from Helge Deller:
- Fix crashes when accessing PCI devices on some machines like C240 and
J5000. The crashes were triggered because we replaced cache flushes
by nops in the alternative coding where we shouldn't for some
machines.
- Dave fixed a race in the usage of the sr1 space register when used to
load the coherence index.
- Use the hardware lpa instruction to to load the physical address of
kernel virtual addresses in the iommu driver code.
- The kernel may fail to link when CONFIG_MLONGCALLS isn't set. Solve
that by rearranging functions in the final vmlinux executeable.
- Some defconfig cleanups and removal of compiler warnings.
* 'parisc-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix crash due alternative coding for NP iopdir_fdc bit
parisc: Use lpa instruction to load physical addresses in driver code
parisc: configs: Remove useless UEVENT_HELPER_PATH
parisc: Use implicit space register selection for loading the coherence index of I/O pdirs
parisc: Fix compiler warnings in float emulation code
parisc/slab: cleanup after /proc/slab_allocators removal
parisc: Allow building 64-bit kernel without -mlong-calls compiler option
parisc: Kconfig: remove ARCH_DISCARD_MEMBLOCK
|
|
Pull crypto fixes from Herbert Xu:
"This fixes a regression that breaks the jitterentropy RNG and a
potential memory leak in hmac"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: hmac - fix memory leak in hmac_init_tfm()
crypto: jitterentropy - change back to module_init()
|
|
Pull xfs fixes from Darrick Wong:
"Here are a couple more bug fixes for 5.2. Changes since last update:
- Fix some forgotten strings in a log debugging function
- Fix incorrect unit conversion in online fsck code"
* tag 'xfs-5.2-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: inode btree scrubber should calculate im_boffset correctly
xfs: fix broken log reservation debugging
|
|
Pull gfs2 fix from Andreas Gruenbacher:
"A revert for a patch that turned out to be broken"
* tag 'gfs2-v5.2.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
Revert "gfs2: Replace gl_revokes with a GLF flag"
|
|
Pull overlayfs fixes from Miklos Szeredi:
"Here's one fix for a class of bugs triggered by syzcaller, and one
that makes xfstests fail less"
* tag 'ovl-fixes-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: doc: add non-standard corner cases
ovl: detect overlapping layers
ovl: support the FS_IOC_FS[SG]ETXATTR ioctls
|
|
Pull fuse fixes from Miklos Szeredi:
"This fixes a leaked inode lock in an error cleanup path and a data
consistency issue with copy_file_range().
It also adds a new flag for the WRITE request that allows userspace
filesystems to clear suid/sgid bits on the file if necessary"
* tag 'fuse-fixes-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: extract helper for range writeback
fuse: fix copy_file_range() in the writeback case
fuse: add FUSE_WRITE_KILL_PRIV
fuse: fallocate: fix return with locked inode
|
|
Pull NFS client fixes from Anna Schumaker:
"These are mostly stable bugfixes found during testing, many during the
recent NFS bake-a-thon.
Stable bugfixes:
- SUNRPC: Fix regression in umount of a secure mount
- SUNRPC: Fix a use after free when a server rejects the RPCSEC_GSS credential
- NFSv4.1: Again fix a race where CB_NOTIFY_LOCK fails to wake a waiter
- NFSv4.1: Fix bug only first CB_NOTIFY_LOCK is handled
Other bugfixes:
- xprtrdma: Use struct_size() in kzalloc()"
* tag 'nfs-for-5.2-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFSv4.1: Fix bug only first CB_NOTIFY_LOCK is handled
NFSv4.1: Again fix a race where CB_NOTIFY_LOCK fails to wake a waiter
SUNRPC: Fix a use after free when a server rejects the RPCSEC_GSS credential
SUNRPC fix regression in umount of a secure mount
xprtrdma: Use struct_size() in kzalloc()
|
|
Fix sparse warning:
drivers/net/ethernet/mscc/ocelot_ace.c:96:3:
warning: symbol 'vcap_data_t' was not declared. Should it be static?
'vcap_data_t' never used so can be removed
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the process issuing a "start" command on the pktgen procfs
interface, acquires the pktgen thread lock and never release it, until
all pktgen threads are completed. The above can blocks indefinitely any
other pktgen command and any (even unrelated) netdevice removal - as
the pktgen netdev notifier acquires the same lock.
The issue is demonstrated by the following script, reported by Matteo:
ip -b - <<'EOF'
link add type dummy
link add type veth
link set dummy0 up
EOF
modprobe pktgen
echo reset >/proc/net/pktgen/pgctrl
{
echo rem_device_all
echo add_device dummy0
} >/proc/net/pktgen/kpktgend_0
echo count 0 >/proc/net/pktgen/dummy0
echo start >/proc/net/pktgen/pgctrl &
sleep 1
rmmod veth
Fix the above releasing the thread lock around the sleep call.
Additionally we must prevent racing with forcefull rmmod - as the
thread lock no more protects from them. Instead, acquire a self-reference
before waiting for any thread. As a side effect, running
rmmod pktgen
while some thread is running now fails with "module in use" error,
before this patch such command hanged indefinitely.
Note: the issue predates the commit reported in the fixes tag, but
this fix can't be applied before the mentioned commit.
v1 -> v2:
- no need to check for thread existence after flipping the lock,
pktgen threads are freed only at net exit time
-
Fixes: 6146e6a43b35 ("[PKTGEN]: Removes thread_{un,}lock() macros.")
Reported-and-tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a valid MAC address is not found the current messages
are shown:
fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa
Since the network device has not been registered at this point, it is better
to use dev_err()/dev_info() instead, which will provide cleaner log
messages like these:
fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa
Tested on a imx6dl-pico-pi board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The monolithic hash_lock could cause huge contention when
inserting/deletiing vxlan_fdbs into the fdb_head.
Use FDB_HASH_SIZE hash_locks to protect insertions/deletions
of vxlan_fdbs into the fdb_head hash table.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Litao jiao <jiaolitao@raisecom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ADFS cleanups/fixes from Russell King:
"As a result of some of Al Viro's great work, here are a few cleanups
with fixes for adfs:
- factor out filename comparison, so we can be sure that
adfs_compare() (used for namei compare) and adfs_match() (used for
lookup) have the same behaviour.
- factor out filename lowering (which is not the same as tolower()
which will lower top-bit-set characters) to ensure that we have the
same behaviour when comparing filenames as when we hash them.
- factor out the object fixups, so we are applying all fixups to
directory objects in the same way, independent of the disk format.
- factor out the object name fixup (into the previously factored out
function) to ensure that filenames are appropriately translated -
for example, adfs allows '/' in filenames, which being the Unix
path separator, need to be translated to a different character,
which is normally '.' (DOS 8.3 filenames represent the . as a / on
adfs, so this is the expected reverse translation.)
- remove filename truncation; Al asked about this and apparently the
decision is to remove it. In any case, adfs's truncation was buggy,
so this rids us of that bug by removing the truncation feature.
- we now have only one location which adds the "filetype" suffix to
the filename, so there's no point that code being out of line.
- since we translate '/' into '.', an adfs filename of "/" or "//"
would end up being translated to "." and ".." which have special
meanings. In this case, change the first character to "^" to avoid
these special directory names being abused"
* tag 'for-rc-adfs' of git://git.armlinux.org.uk/~rmk/linux-arm:
fs/adfs: fix filename fixup handling for "/" and "//" names
fs/adfs: move append_filetype_suffix() into adfs_object_fixup()
fs/adfs: remove truncated filename hashing
fs/adfs: factor out filename fixup
fs/adfs: factor out object fixups
fs/adfs: factor out filename case lowering
fs/adfs: factor out filename comparison
|
|
Use a safe strscpy call to copy the ethtool stat strings into the
relevant buffers, instead of a memcpy that will be accessing
out-of-bound data.
Fixes: 118d6298f6f0 ("net: mvpp2: add ethtool GOP statistics")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a NL_SET_ERR_MSG message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the following tests last for several hours, the problem will occur.
Server:
rds-stress -r 1.1.1.16 -D 1M
Client:
rds-stress -r 1.1.1.14 -s 1.1.1.16 -D 1M -T 30
The following will occur.
"
Starting up....
tsks tx/s rx/s tx+rx K/s mbi K/s mbo K/s tx us/c rtt us cpu
%
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
"
>From vmcore, we can find that clean_list is NULL.
>From the source code, rds_mr_flushd calls rds_ib_mr_pool_flush_worker.
Then rds_ib_mr_pool_flush_worker calls
"
rds_ib_flush_mr_pool(pool, 0, NULL);
"
Then in function
"
int rds_ib_flush_mr_pool(struct rds_ib_mr_pool *pool,
int free_all, struct rds_ib_mr **ibmr_ret)
"
ibmr_ret is NULL.
In the source code,
"
...
list_to_llist_nodes(pool, &unmap_list, &clean_nodes, &clean_tail);
if (ibmr_ret)
*ibmr_ret = llist_entry(clean_nodes, struct rds_ib_mr, llnode);
/* more than one entry in llist nodes */
if (clean_nodes->next)
llist_add_batch(clean_nodes->next, clean_tail, &pool->clean_list);
...
"
When ibmr_ret is NULL, llist_entry is not executed. clean_nodes->next
instead of clean_nodes is added in clean_list.
So clean_nodes is discarded. It can not be used again.
The workqueue is executed periodically. So more and more clean_nodes are
discarded. Finally the clean_list is NULL.
Then this problem will occur.
Fixes: 1bc144b62524 ("net, rds, Replace xlist in net/rds/xlist.h with llist")
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Olivier Matz says:
====================
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
The following code returns EFAULT (Bad address):
s = socket(AF_INET6, SOCK_RAW, IPPROTO_ICMPV6);
setsockopt(s, SOL_IPV6, IPV6_HDRINCL, 1);
sendto(ipv6_icmp6_packet, addr); /* returns -1, errno = EFAULT */
The problem is fixed in the second patch. The first one aligns the
code to ipv4, to avoid a race condition in the second patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following code returns EFAULT (Bad address):
s = socket(AF_INET6, SOCK_RAW, IPPROTO_ICMPV6);
setsockopt(s, SOL_IPV6, IPV6_HDRINCL, 1);
sendto(ipv6_icmp6_packet, addr); /* returns -1, errno = EFAULT */
The IPv4 equivalent code works. A workaround is to use IPPROTO_RAW
instead of IPPROTO_ICMPV6.
The failure happens because 2 bytes are eaten from the msghdr by
rawv6_probe_proto_opt() starting from commit 19e3c66b52ca ("ipv6
equivalent of "ipv4: Avoid reading user iov twice after
raw_probe_proto_opt""), but at that time it was not a problem because
IPV6_HDRINCL was not yet introduced.
Only eat these 2 bytes if hdrincl == 0.
Fixes: 715f504b1189 ("ipv6: add IPV6_HDRINCL option for raw sockets")
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As it was done in commit 8f659a03a0ba ("net: ipv4: fix for a race
condition in raw_sendmsg") and commit 20b50d79974e ("net: ipv4: emulate
READ_ONCE() on ->hdrincl bit-field in raw_sendmsg()") for ipv4, copy the
value of inet->hdrincl in a local variable, to avoid introducing a race
condition in the next commit.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The opts[] array is of type u32. Therefore remove the wrong
cpu_to_le32(). The opts[] array members are converted to little endian
later when being assigned to the respective descriptor fields.
This is not a new issue, it just popped up due to r8169.c having
been renamed and more thoroughly checked. Due to the renaming
this patch applies to net-next only.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 73118ca8baf7 introduced a glock reference counting bug in
gfs2_trans_remove_revoke. Given that, replacing gl_revokes with a GLF flag is
no longer useful, so revert that commit.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
Since GCC 9, the compiler warns about evolution of the
platform-specific ABI, in particular relating for the marshaling of
certain structures involving bitfields.
The kernel is a standalone binary, and of course nobody would be
so stupid as to expose structs containing bitfields as function
arguments in ABI. (Passing a pointer to such a struct, however
inadvisable, should be unaffected by this change. perf and various
drivers rely on that.)
So these warnings do more harm than good: turn them off.
We may miss warnings about future ABI drift, but that's too bad.
Future ABI breaks of this class will have to be debugged and fixed
the traditional way unless the compiler evolves finer-grained
diagnostics.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
According to the found documentation, data cache flushes and sync
instructions are needed on the PCX-U+ (PA8200, e.g. C200/C240)
platforms, while PCX-W (PA8500, e.g. C360) platforms aparently don't
need those flushes when changing the IO PDIR data structures.
We have no documentation for PCX-W+ (PA8600) and PCX-W2 (PA8700) CPUs,
but Carlo Pisani reported that his C3600 machine (PA8600, PCX-W+) fails
when the fdc instructions were removed. His firmware didn't set the NIOP
bit, so one may assume it's a firmware bug since other C3750 machines
had the bit set.
Even if documentation (as mentioned above) states that PCX-W (PA8500,
e.g. J5000) does not need fdc flushes, Sven could show that an Adaptec
29320A PCI-X SCSI controller reliably failed on a dd command during the
first five minutes in his J5000 when fdc flushes were missing.
Going forward, we will now NOT replace the fdc and sync assembler
instructions by NOPS if:
a) the NP iopdir_fdc bit was set by firmware, or
b) we find a CPU up to and including a PCX-W+ (PA8600).
This fixes the HPMC crashes on a C240 and C36XX machines. For other
machines we rely on the firmware to set the bit when needed.
In case one finds HPMC issues, people could try to boot their machines
with the "no-alternatives" kernel option to turn off any alternative
patching.
Reported-by: Sven Schnelle <svens@stackframe.org>
Reported-by: Carlo Pisani <carlojpisani@gmail.com>
Tested-by: Sven Schnelle <svens@stackframe.org>
Fixes: 3847dab77421 ("parisc: Add alternative coding infrastructure")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 5.0+
|
|
Most I/O in the kernel is done using the kernel offset mapping.
However, there is one API that uses aliased kernel address ranges:
> The final category of APIs is for I/O to deliberately aliased address
> ranges inside the kernel. Such aliases are set up by use of the
> vmap/vmalloc API. Since kernel I/O goes via physical pages, the I/O
> subsystem assumes that the user mapping and kernel offset mapping are
> the only aliases. This isn't true for vmap aliases, so anything in
> the kernel trying to do I/O to vmap areas must manually manage
> coherency. It must do this by flushing the vmap range before doing
> I/O and invalidating it after the I/O returns.
For this reason, we should use the hardware lpa instruction to load the
physical address of kernel virtual addresses in the driver code.
I believe we only use the vmap/vmalloc API with old PA 1.x processors
which don't have a sba, so we don't hit this problem.
Tested on c3750, c8000 and rp3440.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Remove the CONFIG_UEVENT_HELPER_PATH because:
1. It is disabled since commit 1be01d4a5714 ("driver: base: Disable
CONFIG_UEVENT_HELPER by default") as its dependency (UEVENT_HELPER) was
made default to 'n',
2. It is not recommended (help message: "This should not be used today
[...] creates a high system load") and was kept only for ancient
userland,
3. Certain userland specifically requests it to be disabled (systemd
README: "Legacy hotplug slows down the system and confuses udev").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
We only support I/O to kernel space. Using %sr1 to load the coherence
index may be racy unless interrupts are disabled. This patch changes the
code used to load the coherence index to use implicit space register
selection. This saves one instruction and eliminates the race.
Tested on rp3440, c8000 and c3750.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Fix a s/TIF_SECOMP/TIF_SECCOMP/ comment typo
Cc: Jiri Kosina <trivial@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Eric Dumazet says:
====================
ipv6: tcp: more control on RST flowlabels
First patch allows to reflect incoming IPv6 flowlabel
on RST packets sent when no socket could handle the packet.
Second patch makes sure we send the same flowlabel
for RST or ACK packets on behalf of TIME_WAIT sockets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 1d13a96c74fc ("ipv6: tcp: fix flowlabel value in ACK
messages"), we stored in tw_flowlabel the flowlabel, in the
case ACK packets needed to be sent on behalf of a TIME_WAIT socket.
We can use the same field so that RST packets sent from
TIME_WAIT state also use a consistent flowlabel.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When RST packets are sent because no socket could be found,
it makes sense to use flowlabel_reflect sysctl to decide
if a reflection of the flowlabel is requested.
This extends commit 22b6722bfa59 ("ipv6: Add sysctl for per
namespace flow label reflection"), for some TCP RST packets.
In order to provide full control of this new feature,
flowlabel_reflect becomes a bitmask.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct objagg_stats {
...
struct objagg_obj_stats_info stats_info[];
};
size = sizeof(*objagg_stats) + sizeof(objagg_stats->stats_info[0]) * count;
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, stats_info, count), GFP_KERNEL);
Notice that, in this case, variable alloc_size is not necessary, hence it
is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
small cleanup: "struct request_sock_queue *queue" parameter of reqsk_queue_unlink
func is never used in the func, so we can remove it.
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit e9919a24d3022f72bcadc407e73a6ef17093a849.
Nathan reported the new behaviour breaks Android, as Android just add
new rules and delete old ones.
If we return 0 without adding dup rules, Android will remove the new
added rules and causing system to soft-reboot.
Fixes: e9919a24d302 ("fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Reported-by: Yaro Slav <yaro330@gmail.com>
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the early days of phylib we had a functionality that changed to the
next lower speed in fixed mode if no link was established after a
certain period of time. This functionality has been removed years ago,
and state PHY_FORCING isn't needed any longer. Instead we can go from
UP to RUNNING or NOLINK directly (same as in autoneg mode).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WoL magic packet configuration sometimes does not work due to
couple of leakages found.
Mainly there was a regression introduced during readx_poll refactoring.
Next, fw request waiting time was too small. Sometimes that
caused sleep proxy config function to return with an error
and to skip WoL configuration.
At last, WoL data were passed to FW from not clean buffer.
That could cause FW to accept garbage as a random configuration data.
Fixes: 6a7f2277313b ("net: aquantia: replace AQ_HW_WAIT_FOR with readx_poll_timeout_atomic")
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ethtool_get_regs() allocates a buffer of size ops->get_regs_len(),
and pass it to the kernel driver via ops->get_regs() for filling.
There is no restriction about what the kernel drivers can or cannot do
with the open ethtool_regs structure. They usually set regs->version
and ignore regs->len or set it to the same size as ops->get_regs_len().
But if userspace allocates a smaller buffer for the registers dump,
we would cause a userspace buffer overflow in the final copy_to_user()
call, which uses the regs.len value potentially reset by the driver.
To fix this, make this case obvious and store regs.len before calling
ops->get_regs(), to only copy as much data as requested by userspace,
up to the value returned by ops->get_regs_len().
While at it, remove the redundant check for non-null regbuf.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot found the following leak in sctp_process_init
BUG: memory leak
unreferenced object 0xffff88810ef68400 (size 1024):
comm "syz-executor273", pid 7046, jiffies 4294945598 (age 28.770s)
hex dump (first 32 bytes):
1d de 28 8d de 0b 1b e3 b5 c2 f9 68 fd 1a 97 25 ..(........h...%
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000a02cebbd>] kmemleak_alloc_recursive include/linux/kmemleak.h:55
[inline]
[<00000000a02cebbd>] slab_post_alloc_hook mm/slab.h:439 [inline]
[<00000000a02cebbd>] slab_alloc mm/slab.c:3326 [inline]
[<00000000a02cebbd>] __do_kmalloc mm/slab.c:3658 [inline]
[<00000000a02cebbd>] __kmalloc_track_caller+0x15d/0x2c0 mm/slab.c:3675
[<000000009e6245e6>] kmemdup+0x27/0x60 mm/util.c:119
[<00000000dfdc5d2d>] kmemdup include/linux/string.h:432 [inline]
[<00000000dfdc5d2d>] sctp_process_init+0xa7e/0xc20
net/sctp/sm_make_chunk.c:2437
[<00000000b58b62f8>] sctp_cmd_process_init net/sctp/sm_sideeffect.c:682
[inline]
[<00000000b58b62f8>] sctp_cmd_interpreter net/sctp/sm_sideeffect.c:1384
[inline]
[<00000000b58b62f8>] sctp_side_effects net/sctp/sm_sideeffect.c:1194
[inline]
[<00000000b58b62f8>] sctp_do_sm+0xbdc/0x1d60 net/sctp/sm_sideeffect.c:1165
[<0000000044e11f96>] sctp_assoc_bh_rcv+0x13c/0x200
net/sctp/associola.c:1074
[<00000000ec43804d>] sctp_inq_push+0x7f/0xb0 net/sctp/inqueue.c:95
[<00000000726aa954>] sctp_backlog_rcv+0x5e/0x2a0 net/sctp/input.c:354
[<00000000d9e249a8>] sk_backlog_rcv include/net/sock.h:950 [inline]
[<00000000d9e249a8>] __release_sock+0xab/0x110 net/core/sock.c:2418
[<00000000acae44fa>] release_sock+0x37/0xd0 net/core/sock.c:2934
[<00000000963cc9ae>] sctp_sendmsg+0x2c0/0x990 net/sctp/socket.c:2122
[<00000000a7fc7565>] inet_sendmsg+0x64/0x120 net/ipv4/af_inet.c:802
[<00000000b732cbd3>] sock_sendmsg_nosec net/socket.c:652 [inline]
[<00000000b732cbd3>] sock_sendmsg+0x54/0x70 net/socket.c:671
[<00000000274c57ab>] ___sys_sendmsg+0x393/0x3c0 net/socket.c:2292
[<000000008252aedb>] __sys_sendmsg+0x80/0xf0 net/socket.c:2330
[<00000000f7bf23d1>] __do_sys_sendmsg net/socket.c:2339 [inline]
[<00000000f7bf23d1>] __se_sys_sendmsg net/socket.c:2337 [inline]
[<00000000f7bf23d1>] __x64_sys_sendmsg+0x23/0x30 net/socket.c:2337
[<00000000a8b4131f>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:3
The problem was that the peer.cookie value points to an skb allocated
area on the first pass through this function, at which point it is
overwritten with a heap allocated value, but in certain cases, where a
COOKIE_ECHO chunk is included in the packet, a second pass through
sctp_process_init is made, where the cookie value is re-allocated,
leaking the first allocation.
Fix is to always allocate the cookie value, and free it when we are done
using it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: syzbot+f7e9153b037eac9b1df8@syzkaller.appspotmail.com
CC: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When KASAN is enabled, after several rds connections are
created, then "rmmod rds_rdma" is run. The following will
appear.
"
BUG rds_ib_incoming (Not tainted): Objects remaining
in rds_ib_incoming on __kmem_cache_shutdown()
Call Trace:
dump_stack+0x71/0xab
slab_err+0xad/0xd0
__kmem_cache_shutdown+0x17d/0x370
shutdown_cache+0x17/0x130
kmem_cache_destroy+0x1df/0x210
rds_ib_recv_exit+0x11/0x20 [rds_rdma]
rds_ib_exit+0x7a/0x90 [rds_rdma]
__x64_sys_delete_module+0x224/0x2c0
? __ia32_sys_delete_module+0x2c0/0x2c0
do_syscall_64+0x73/0x190
entry_SYSCALL_64_after_hwframe+0x44/0xa9
"
This is rds connection memory leak. The root cause is:
When "rmmod rds_rdma" is run, rds_ib_remove_one will call
rds_ib_dev_shutdown to drop the rds connections.
rds_ib_dev_shutdown will call rds_conn_drop to drop rds
connections as below.
"
rds_conn_path_drop(&conn->c_path[0], false);
"
In the above, destroy is set to false.
void rds_conn_path_drop(struct rds_conn_path *cp, bool destroy)
{
atomic_set(&cp->cp_state, RDS_CONN_ERROR);
rcu_read_lock();
if (!destroy && rds_destroy_pending(cp->cp_conn)) {
rcu_read_unlock();
return;
}
queue_work(rds_wq, &cp->cp_down_w);
rcu_read_unlock();
}
In the above function, destroy is set to false. rds_destroy_pending
is called. This does not move rds connections to ib_nodev_conns.
So destroy is set to true to move rds connections to ib_nodev_conns.
In rds_ib_unregister_client, flush_workqueue is called to make rds_wq
finsh shutdown rds connections. The function rds_ib_destroy_nodev_conns
is called to shutdown rds connections finally.
Then rds_ib_recv_exit is called to destroy slab.
void rds_ib_recv_exit(void)
{
kmem_cache_destroy(rds_ib_incoming_slab);
kmem_cache_destroy(rds_ib_frag_slab);
}
The above slab memory leak will not occur again.
>From tests,
256 rds connections
[root@ca-dev14 ~]# time rmmod rds_rdma
real 0m16.522s
user 0m0.000s
sys 0m8.152s
512 rds connections
[root@ca-dev14 ~]# time rmmod rds_rdma
real 0m32.054s
user 0m0.000s
sys 0m15.568s
To rmmod rds_rdma with 256 rds connections, about 16 seconds are needed.
And with 512 rds connections, about 32 seconds are needed.
>From ftrace, when one rds connection is destroyed,
"
19) | rds_conn_destroy [rds]() {
19) 7.782 us | rds_conn_path_drop [rds]();
15) | rds_shutdown_worker [rds]() {
15) | rds_conn_shutdown [rds]() {
15) 1.651 us | rds_send_path_reset [rds]();
15) 7.195 us | }
15) + 11.434 us | }
19) 2.285 us | rds_cong_remove_conn [rds]();
19) * 24062.76 us | }
"
So if many rds connections will be destroyed, this function
rds_ib_destroy_nodev_conns uses most of time.
Suggested-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable cache_allocs is to indicate how many frags (KiB) are in one
rds connection frag cache.
The command "rds-info -Iv" will output the rds connection cache
statistics as below:
"
RDS IB Connections:
LocalAddr RemoteAddr Tos SL LocalDev RemoteDev
1.1.1.14 1.1.1.14 58 255 fe80::2:c903:a:7a31 fe80::2:c903:a:7a31
send_wr=256, recv_wr=1024, send_sge=8, rdma_mr_max=4096,
rdma_mr_size=257, cache_allocs=12
"
This means that there are about 12KiB frag in this rds connection frag
cache.
Since rds.h in rds-tools is not related with the kernel rds.h, the change
in kernel rds.h does not affect rds-tools.
rds-info in rds-tools 2.0.5 and 2.0.6 is tested with this commit. It works
well.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Biao Huang says:
====================
complete dwmac-mediatek driver and fix flow control issue
Changes in v2:
patch#1: there is no extra action in mediatek_dwmac_remove, remove it
v1:
This series mainly complete dwmac-mediatek driver:
1. add power on/off operations for dwmac-mediatek.
2. disable rx watchdog to reduce rx path reponding time.
3. change the default value of tx-frames from 25 to 1, so
ptp4l will test pass by default.
and also fix the issue that flow control won't be disabled any more
once being enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current dwmac4_flow_ctrl will not clear
GMAC_RX_FLOW_CTRL_RFE/GMAC_RX_FLOW_CTRL_RFE bits,
so MAC hw will keep flow control on although expecting
flow control off by ethtool. Add codes to fix it.
Fixes: 477286b53f55 ("stmmac: add GMAC4 core support")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the default value of tx-frames is 25, it's too late when
passing tstamp to stack, then the ptp4l will fail:
ptp4l -i eth0 -f gPTP.cfg -m
ptp4l: selected /dev/ptp0 as PTP clock
ptp4l: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l: port 1: link up
ptp4l: timed out while polling for tx timestamp
ptp4l: increasing tx_timestamp_timeout may correct this issue,
but it is likely caused by a driver bug
ptp4l: port 1: send peer delay response failed
ptp4l: port 1: LISTENING to FAULTY on FAULT_DETECTED (FT_UNSPECIFIED)
ptp4l tests pass when changing the tx-frames from 25 to 1 with
ethtool -C option.
It should be fine to set tx-frames default value to 1, so ptp4l will pass
by default.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
disable rx watchdog for dwmac-mediatek, then the hw will
issue a rx interrupt once receiving a packet, so the responding time
for rx path will be reduced.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add Ethernet power on/off operations in init/exit flow.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Jianlin's testing, netperf was broken with 'Connection reset by peer',
as the cookie check failed in rt6_check() and ip6_dst_check() always
returned NULL.
It's caused by Commit 93531c674315 ("net/ipv6: separate handling of FIB
entries from dst based routes"), where the cookie can be got only when
'c1'(see below) for setting dst_cookie whereas rt6_check() is called
when !'c1' for checking dst_cookie, as we can see in ip6_dst_check().
Since in ip6_dst_check() both rt6_dst_from_check() (c1) and rt6_check()
(!c1) will check the 'from' cookie, this patch is to remove the c1 check
in rt6_get_cookie(), so that the dst_cookie can always be set properly.
c1:
(rt->rt6i_flags & RTF_PCPU || unlikely(!list_empty(&rt->rt6i_uncached)))
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Jakub Kicinski
Robert Hancock
Linus Torvalds
YueHaibing
Paolo Abeni
Fabio Estevam
Litao jiao
Maxime Chevallier
Colin Ian King
Zhu Yanjun
David S. Miller
Olivier Matz
Heiner Kallweit
Bob Peterson
Dave Martin
Helge Deller
John David Anglin
Krzysztof Kozlowski
George G. Davis
Eric Dumazet
Gustavo A. R. Silva
Zhiqiang Liu
Hangbin Liu
Nikita Danilov
Vivien Didelot
Neil Horman
Biao Huang
Xin Long