| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is needed as the earlier method of manipulating this register via PCI
Config space is disallowed by certain Hypervisors.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the NIC PCI function may be used by other protocols, the chip interrupts
must be enabled in be_probe() itself rather than be_open().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
COMPAT_NET_DEV_OPS was removed a while back and with it the definition of
netdev_resync_ops() went away. Let's finish the clean-up.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The resource ID used for VM socket control packets (0) is already
used for the VMCI_GET_CONTEXT_ID hypercall so a new ID (15) must be
used when the guest sends these datagrams to the hypervisor.
The hypervisor context ID must also be removed from the internal
blacklist.
Signed-off-by: Reilly Grant <grantr@vmware.com>
Acked-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows LRO aggregation on bonded devices that contain an
NX3031 device. It also adds a for_each_netdev_in_bond_rcu(bond, slave)
macro which executes for each slave that has bond as master.
V3: After testing and discussing this with Rajesh, I decided to keep the
vlan ip cache and just rename it to ip_cache since it will store bond
ip addresses too. A new master flag has been added to the ip cache to
denote that the address has been added because of a master device.
I've taken care of the enslave/release cases by checking for various
combinations of events and flags (e.g. netxen has a master, it's a
bond master and it's not marked as a slave means it is being enslaved
and is dev_open()ed in bond_enslave).
I've changed netxen_free_ip_list() to have a "master" parameter which
causes all IP addresses marked as master to be deleted (used when a
netxen is being released). I've made the patch use the new upper
device API as well. The following cases were tested:
- bond -> netxen
- vlan -> netxen
- vlan -> bond -> netxen
V2: Remove local ip caching, retrieve addresses dynamically and
restore them if necessary.
Note: Tested with NX3031 adapter.
Tested-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Andy Gospodarek <agospoda@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Included changes:
- introduction of the new Network Coding component. This new mechanism aims to
increase throughput by fusing multiple packets in one transmission.
- minor cleanups
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes chip specific operations from the common hardware
paths, as well as the Makefile change to accomodate the new files.
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch defines the common operations to support multiple chips. It
includes common header file modifications to support the current chips
(T4 and T5). It also includes the following bug fixes:
- reconfirms the rnode state after an implicit logo.
- corrects the stats array size.
- sets up and checks flags correctly when coming up as master and finding
the card initialized
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch creates a new file for T5 adapter operations.
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch separates T4 adapter operations into a new file.
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
T5 adapter does not support onchip queue memory. Present logic fails to
allocate QP for T5 and returns an error. Also, if module parameter ocqp_support
is zero then we are unable to allocate QP which should not be the case. Ideally
if ocqp_support parameter is 0 or onchip queue support is disable then host QP
should be allocated before returning an error.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Always bump the tcam_full stat. Also, bump wr reply timeout to 30 seconds.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It enables direct DMA by HW to memory region PBL arrays and fast register PBL
arrays from host memory, vs the T4 way of passing these arrays in the WR itself.
The result is lower latency for memory registration, and larger PBL array
support for fast register operations.
This patch also updates ULP_TX_MEM_WRITE command fields for T5. Ordering bit of
ULP_TX_MEM_WRITE is at bit position 22 in T5 and at 23 in T4.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both DB Flow-Control and DB Coalescing are disabled by default on T5
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for Chelsio T5 adapter.
Enables T5's Write Combining feature.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All T5 adapters will only support VFs on PF0-3 despite the ability of the
hardware to support them on PF4-7. This keeps our T4 and T5 adapters more
similar which simplifies host driver software.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements a low latency Write Combining (aka Write Coalescing) work
request path. PCIE maps User Space Doorbell BAR2 region writes to the new
interface to SGE. SGE pulls a new message from PCIE new interface and if its a
coalesced write work request then pushes it for processing. This patch copies
coalesced work request to memory mapped BAR2 space.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving a network coded packet, the decoding buffer is searched
for a packet to use for decoding. The source, destination, and crc32 from
the coded packet is used to identify the wanted packet. The decoded
packet is passed to the usual unicast receiver function, as had it never
been network coded.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
To be able to decode a network coded packet, a node must already know
one of the two coded packets. This is done by buffering skbs before
transmission and buffering packets sniffed with promiscuous mode from
other hosts.
Packets are kept in a buffer similar to the one with forward-skbs: A
hash table, where each entry, which corresponds to a src-dst pair, has a
linked list packets.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
Before adding forward-skbs to the coding buffer, the buffer is searched
for a potential coding opportunity. If one is found, the two packets are
network coded and transmitted right away. If not, the forward-skb is
added to the buffer.
Network coded packets are transmitted with information about the two
receivers and the two coded packets. The first receiver is given by the
MAC header, while the second is given in the payload/bat-header. The
second receiver uses promiscuous mode to receive the packet and check
the second destination.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
Two be able to network code two packets, one packet must be buffered
until the next is available. This is done in a "coding buffer", which is
essentially a hash table with lists of packets. Each entry in the hash
table corresponds to a specific src-dst pair, which has a linked list of
packets that are buffered.
This patch adds skbs to the buffer just before forwarding them. The
buffer is traversed every 10 ms, where timed skbs are removed from the
buffer and transmitted. To allow experiments with the network coding
scheme, the timeout is tunable through a file in debugfs.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
To use network coding efficiently, a relay must know when neighbor nodes
are likely to have enough information to be able to decode a network
coded packet. This is detected by using OGMs from batman-adv to discover
when one neighbor is in range of another neighbor. The relay check the
TLL to detect when an OGM is forwarded from one neighbor by another
neighbor, and thereby knows that the two neighbors are in range and thus
overhear packets sent by each other.
This information is saved in the orig_node struct to be used when
searching for coding opportunities. Two lists are added to the
orig_node struct: One for neighbors that can hear the orig_node
(outgoing nc_nodes) and one for neighbors that the orig_node can hear
(incoming nc_nodes).
Information about nc_nodes is kept for 10 seconds and is available
through debugfs in batman_adv/nc_nodes to use when debugging network
coding.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
Network coding exploits the 802.11 shared medium to allow multiple
packets to be sent in a single transmission. In brief, a relay can XOR
two packets, and send the coded packet to two destinations. The
receivers can decode one of the original packets by XOR'ing the coded
packet with the other original packet. This will lead to increased
throughput in topologies where two packets cross one relay.
In a simple topology with three nodes, it takes four transmissions
without network coding to get one packet from Node A to Node B and one
from Node B to Node A:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <--- p2 ---- Node R Node B
4. Node A Node R ---- p1 ---> Node B
With network coding, the relay only needs one transmission, which saves
us one slot of valuable airtime:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <- p1 x p2 - Node R - p1 x p2 -> Node B
The same principle holds for a topology including five nodes. Here the
packets from Node A and Node B are overheard by Node C and Node D,
respectively. This allows Node R to send a network coded packet to save
one transmission:
Node A Node B
| \ / |
| p1 p2 |
| \ / |
p1 > Node R < p2
| |
| / \ |
| p1 x p2 p1 x p2 |
v / \ v
/ \
Node C < > Node D
More information is available on the open-mesh.org wiki[1].
This patch adds the initial code to support network coding in
batman-adv. It sets up a worker thread to do house keeping and adds a
sysfs file to enable/disable network coding. The feature is disabled by
default, as it requires a wifi-driver with working promiscuous mode, and
also because it adds a small delay at each hop.
[1] http://www.open-mesh.org/projects/batman-adv/wiki/Catwoman
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
In C standard any expression different from 0 will be converted to
'true' when casting to bool (whatever is the length of the value).
Therefore all the "!!" conversions can be removed.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
batadv_check_unicast_packet() is changed to return a value based on the
reason to drop the packet, which will be useful information for
future users of batadv_check_unicast_packet().
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
The batadv_priv struct carries a pointer to its own interface
struct. Therefore, it is not necessary to retrieve the soft_iface
via the primary interface.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
The variable dev is initialized but never used
otherwise, so remove the unused variable.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QLogic applications use these callbacks to perform
o NIC Partitioning (NPAR) configuration and management
o Diagnostic tests
o Flash access and updates
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mugunthan V N says:
====================
This patch serires implements the following features in CPSW driver
* get/set phy link settings
* interrupt pacing
* get phy id via ioctl cmd SIOCGMIIPHY
Changes from initial version
* Made active-slave common for cpts, ethtool and SIOCGMIIPHY ioctl
* Cleaned CPSW DT binding documentation by seperating slave nodes
under sub-section
* implemented get phy id via ioctl cmd SIOCGMIIPHY
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement get phy_id via ioctl SIOCGMIIPHY. In switch mode active phy_id
is returned and in dual EMAC mode slave's specific phy_id is returned.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements support for interrupt pacing block of CPSW via ethtool
Inetrrupt pacing block is common of both the ethernet interface in
dual emac mode
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements get/set of the phy settings via ethtool apis
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change cpts_active_slave to active_slave so that the same DT property
can be used to ethtool and SIOCGMIIPHY.
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move all the slave note properties to separate section to reduce the
confusion between slave note properties and cpsw node properties
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement to collect ethernet statistical information on ks8851_mll device.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
remove cast for kmalloc/kzalloc return value.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Joe Perches
Somnath Kotur
Fernando Luis Vazquez Cao
Reilly Grant
nikolay@redhat.com
David S. Miller
Arvind Bhushan
Vipul Pandya
Santosh Rastapur
Martin Hundebøll
Antonio Quartulli
Marek Lindner
Wei Yongjun
Shahed Shaikh
Himanshu Madhani
Mugunthan V N
David J. Choi
Zhang Yanfei