| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
At least therm/fantog "attempts" to work around this issue, which could
lead to corruption of the pending alarm list.
Fix it properly by not updating the timestamp without the lock held, or
trying to add an already pending alarm to the pending alarm list....
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
|
|
If the time to the next alarm is short enough, we could race with HW and
end up with an ~4 second delay until it triggers.
Fix this by checking again after we update HW.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
|
|
Fixes a race where we can miss an alarm that triggers while we're already
processing previous alarms.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
|
|
object->engine cannot be NULL, it's either valid, or an error pointer.
This particular condition shouldn't actually be possible, but just in
case, we'll keep it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This reg has moved on Pascal, and causes a bus fault.
We never use the value anyway, so just remove the read.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
The DRM core used to only call prepare_fb/cleanup_fb() when a plane's
framebuffer changed, which achieved the desired effect.
It's apparently now up to the driver to decide on its own.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org [4.11+]
|
|
This "optimisation" (which was originally meant to skip updating cursor
settings in the core channel on position-only updates) turned out to be
pointless in the final design of the code before it was merged.
Remove it completely, as it breaks other cases.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org [4.10+]
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Pull more documentation updates from Jonathan Corbet:
"Connect the newly RST-formatted documentation to the rest; this had to
wait until the input pull was done. There's also a few small fixes
that wandered in"
* tag 'docs-4.12-2' of git://git.lwn.net/linux:
doc: replace FTP URL to kernel.org with HTTPS one
docs: update references to the device io book
Documentation: earlycon: fix Marvell Armada 3700 UART name
docs-rst: add input docs at main index and use kernel-figure
|
|
Pull more arm64 updates from Catalin Marinas:
- Silence module allocation failures when CONFIG_ARM*_MODULE_PLTS is
enabled. This requires a check for __GFP_NOWARN in alloc_vmap_area()
- Improve/sanitise user tagged pointers handling in the kernel
- Inline asm fixes/cleanups
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Silence first allocation with CONFIG_ARM64_MODULE_PLTS=y
ARM: Silence first allocation with CONFIG_ARM_MODULE_PLTS=y
mm: Silence vmap() allocation failures based on caller gfp_flags
arm64: uaccess: suppress spurious clang warning
arm64: atomic_lse: match asm register sizes
arm64: armv8_deprecated: ensure extension of addr
arm64: uaccess: ensure extension of access_ok() addr
arm64: ensure extension of smp_store_release value
arm64: xchg: hazard against entire exchange variable
arm64: documentation: document tagged pointer stack constraints
arm64: entry: improve data abort handling of tagged pointers
arm64: hw_breakpoint: fix watchpoint matching for tagged pointers
arm64: traps: fix userspace cache maintenance emulation on a tagged pointer
|
|
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"There is nothing really major here, just a couple of small bugfixes,
improvements and cleanups.
- fix handling of probing errors in omapfb (Arvind Yadav)
- remove incorrect __exit markups in few drivers (Dmitry Torokhov)
- fix boot time logo support for drivers using deferred probe
(Takeshi Kihara)
- fix DMA allocation size for ARM CLCD driver (Liam Beguin)
- add support for specifying size via xenstore in xen-frontfb
(Juergen Gross)
- support for AUS mode in imxfb driver (Martin Kaiser)
- fix buffer on stack usage in udlfb driver (Maksim Salau)
- probe failure path fixup in sm501fb driver (Alexey Khoroshilov)
- fix config dependency loop for stifb driver (Arnd Bergmann)
- misc cleanups (Joe Perches, Christophe Leroy, Karim Eshapa, Pushkar
Jambhlekar)"
* tag 'fbdev-v4.12' of git://github.com/bzolnier/linux:
fbdev: sti: don't select CONFIG_VT
drivers/video/fbdev/omap/lcd_mipid.c: Use time comparison kernel macros
sm501fb: don't return zero on failure path in sm501fb_start()
video: fbdev: udlfb: Fix buffer on stack
video: console: Remove reference to CONFIG_8xx
dt-bindings: display: imx: entry for AUS mode
video: fbdev: imxfb: support AUS mode
drivers/video/fbdev: Fixing coding guidelines in acornfb.c
xen, fbfront: add support for specifying size via xenstore
video: ARM CLCD: fix dma allocation size
drivers/video: Convert remaining uses of pr_warning to pr_warn
video/logo: tidyup fb_logo_late_init initcall timing
video: fbdev: i810: remove incorrect __exit markups
video: fbdev: pmag-aa-fb: remove incorrect __exit markups
video: fbdev: pmagb-b-fb: remove incorrect __exit markups
video: fbdev: pmag-ba-fb: remove incorrect __exit markups
omapfb: dss: Handle return errors in dss_init_ports()
|
|
Pull block fixes from Jens Axboe:
"A smaller collection of fixes that should go into -rc1. This contains:
- A fix from Christoph, fixing a regression with the WRITE_SAME and
partial completions. Caused a BUG() on ppc.
- Fixup for __blk_mq_stop_hw_queues(), it should be static. From
Colin.
- Removal of dmesg error messages on elevator switching, when invoked
from sysfs. From me.
- Fix for blk-stat, using this_cpu_ptr() in a section only protected
by rcu_read_lock(). This breaks when PREEMPT_RCU is enabled. From
me.
- Two fixes for BFQ from Paolo, one fixing a crash and one updating
the documentation.
- An error handling lightnvm memory leak, from Rakesh.
- The previous blk-mq hot unplug lock reversal depends on the CPU
hotplug rework that isn't in mainline yet. This caused a lockdep
splat when people unplugged CPUs with blk-mq devices. From Wanpeng.
- A regression fix for DIF/DIX on blk-mq. From Wen"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: handle partial completions for special payload requests
blk-mq: NVMe 512B/4K+T10 DIF/DIX format returns I/O error on dd with split op
blk-stat: don't use this_cpu_ptr() in a preemptable section
elevator: remove redundant warnings on IO scheduler switch
block, bfq: stress that low_latency must be off to get max throughput
block, bfq: use pointer entity->sched_data only if set
nvme: lightnvm: fix memory leak
blk-mq: make __blk_mq_stop_hw_queues static
lightnvm: remove unused rq parameter of nvme_nvm_rqtocmd() to kill warning
block/mq: fix potential deadlock during cpu hotplug
|
|
FTP services were shutdown some weeks ago, so the FTP URL
does not work anymore. Fix this by replacing it with
corresponding HTTPS URL.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Pull MTD updates from Brian Norris:
"NAND, from Boris:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
SPI NOR, from Cyrille:
- fixes in the hisi, intel and Mediatek SPI controller drivers
- fixes to some SPI flash memories not supporting the Chip Erase
command.
- add support to some new memory parts (Winbond, Macronix, Micron,
ESMT).
- add new driver for the STM32 QSPI controller
And a few fixes for Gemini and Versatile platforms on physmap-of"
* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
MAINTAINERS: Update NAND subsystem git repositories
mtd: nand: gpio: update binding
mtd: nand: add ooblayout for old hamming layout
mtd: oxnas_nand: Allocating more than necessary in probe()
dt-bindings: mtd: Document the STM32 QSPI bindings
mtd: mtk-nor: set controller's address width according to nor flash
mtd: spi-nor: add driver for STM32 quad spi flash controller
mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
mtd: nand: davinci: add comment on NAND subpage write status on keystone
mtd: nand: omap2: Fix partition creation via cmdline mtdparts
mtd: nand: NULL terminate a of_device_id table
mtd: nand: Fix a couple error codes
mtd: nand: allow drivers to request minimum alignment for passed buffer
mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
mtd: nand: denali: allow to override revision number
mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
mtd: nand: denali_dt: remove dma-mask DT property
mtd: nand: denali: support 64bit capable DMA engine
mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
mtd: nand: denali: support HW_ECC_FIXUP capability
...
|
|
SCSI devices can return short writes on Write Same just like for normal
writes, so we need to handle this case for our special payload requests
as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
When booted as pv-guest the p2m list presented by the Xen is already
mapped to virtual addresses. In dom0 case the hypervisor might make use
of 2M- or 1G-pages for this mapping. Unfortunately while being properly
aligned in virtual and machine address space, those pages might not be
aligned properly in guest physical address space.
So when trying to obtain the guest physical address of such a page
pud_pfn() and pmd_pfn() must be avoided as those will mask away guest
physical address bits not being zero in this special case.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
When running as Xen pv guest X86_BUG_SYSRET_SS_ATTRS must not be set
on AMD cpus.
This bug/feature bit is kind of special as it will be used very early
when switching threads. Setting the bit and clearing it a little bit
later leaves a critical window where things can go wrong. This time
window has enlarged a little bit by using setup_clear_cpu_cap() instead
of the hypervisor's set_cpu_features callback. It seems this larger
window now makes it rather easy to hit the problem.
The proper solution is to never set the bit in case of Xen.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
When CONFIG_ARM64_MODULE_PLTS is enabled, the first allocation using the
module space fails, because the module is too big, and then the module
allocation is attempted from vmalloc space. Silence the first allocation
failure in that case by setting __GFP_NOWARN.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When CONFIG_ARM_MODULE_PLTS is enabled, the first allocation using the
module space fails, because the module is too big, and then the module
allocation is attempted from vmalloc space. Silence the first allocation
failure in that case by setting __GFP_NOWARN.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
If the caller has set __GFP_NOWARN don't print the following message:
vmap allocation for size 15736832 failed: use vmalloc=<size> to increase
size.
This can happen with the ARM/Linux or ARM64/Linux module loader built
with CONFIG_ARM{,64}_MODULE_PLTS=y which does a first attempt at loading
a large module from module space, then falls back to vmalloc space.
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
As of commits d8f347ba35cf ("nios2: enable earlycon support"),
0dcc0542a006 ("serial: altera_jtaguart: add earlycon support") and
4d9d7d896d77 ("serial: altera_uart: add earlycon support"), the nios2
architecture and the altera_uart/altera_jtaguart drivers support
earlycon. Thus, the custom early console implementation for nios2 is no
longer necessary to get early boot messages. Remove it and rely fully on
earlycon support.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
|
|
This reverts commit 0e2eb7d12eaa8e391bf5615d4271bb87a649caaa
Author: Bart Van Assche <bart.vanassche@sandisk.com>
Date: Thu Mar 30 10:12:39 2017 -0700
target: Fix VERIFY and WRITE VERIFY command parsing
This patch broke existing behaviour for WRITE_VERIFY because
it dropped the original SCF_SCSI_DATA_CDB assignment for
bytchk = 0 so target_cmd_size_check() no longer rejected
this case, allowing an overflow case to trigger an OOPs
in iscsi-target.
Since the short term and long term fixes are still being
discussed, revert it for now since it's late in the merge
window and try again in v4.13-rc1.
Conflicts:
drivers/target/target_core_sbc.c
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The conversion of __dax_zero_page_range() to 'struct dax_operations'
caused it to frequently fail. The mistake was treating the @size
parameter as a dax mapping length rather than just a length of the
clear_pmem() operation. The dax mapping length is assumed to be hard
coded as PAGE_SIZE.
Without this fix any page unaligned zeroing request will trigger a
-EINVAL return from bdev_dax_pgoff().
Cc: Jan Kara <jack@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Fixes: cccbce671582 ("filesystem-dax: convert to dax_direct_access()")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
If we had badblocks/poison in the metadata area of a BTT, recreating the
BTT would not clear the poison in all cases, notably the flog area. This
is because rw_bytes will only clear errors if the request being sent
down is 512B aligned and sized.
Make sure that when writing the map and info blocks, the rw_bytes being
sent are of the correct size/alignment. For the flog, instead of doing
the smaller log_entry writes only, first do a 'wipe' of the entire area
by writing zeroes in large enough chunks so that errors get cleared.
Cc: Andy Rudoff <andy.rudoff@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
nsio_rw_bytes can clear media errors, but this cannot be done while we
are in an atomic context due to locking within ACPI. From the BTT,
->rw_bytes may be called either from atomic or process context depending
on whether the calls happen during initialization or during IO.
During init, we want to ensure error clearing happens, and the flag
marking process context allows nsio_rw_bytes to do that. When called
during IO, we're in atomic context, and error clearing can be skipped.
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Pull Kbuild UAPI updates from Masahiro Yamada:
"Improvement of headers_install by Nicolas Dichtel.
It has been long since the introduction of uapi directories, but the
de-coupling of exported headers has not been completed. Headers listed
in header-y are exported whether they exist in uapi directories or
not. His work fixes this inconsistency.
All (and only) headers under uapi directories are now exported. The
asm-generic wrappers are still exceptions, but this is a big step
forward"
* tag 'kbuild-uapi-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
arch/include: remove empty Kbuild files
uapi: export all arch specifics directories
uapi: export all headers under uapi directories
smc_diag.h: fix include from userland
btrfs_tree.h: fix include from userland
uapi: includes linux/types.h before exporting files
Makefile.headersinst: remove destination-y option
Makefile.headersinst: cleanup input files
x86: stop exporting msr-index.h to userland
nios2: put setup.h in uapi
h8300: put bitsperlong.h in uapi
|
|
Pull misc Kbuild updates from Masahiro Yamada:
- clean up builddeb script
- use full path for KBUILD_IMAGE to fix rpm-pkg build
- fix objdiff tool to ignore debug info
* tag 'kbuild-misc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
builddeb: fix typo
builddeb: Update a few outdated and hardcoded strings
deb-pkg: Remove the KBUILD_IMAGE workaround
unicore32: Use full path in KBUILD_IMAGE definition
sh: Use full path in KBUILD_IMAGE definition
arc: Use full path in KBUILD_IMAGE definition
arm: Use full path in KBUILD_IMAGE definition
arm64: Use full path in KBUILD_IMAGE definition
scripts: objdiff: Ignore debug info when comparing
|
|
Pull Kbuild updates from Masahiro Yamada:
- improve Clang support
- clean up various Makefiles
- improve build log visibility (objtool, alpha, ia64)
- improve compiler flag evaluation for better build performance
- fix GCC version-dependent warning
- fix genksyms
* tag 'kbuild-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (23 commits)
kbuild: dtbinst: remove unnecessary __dtbs_install_prep target
ia64: beatify build log for gate.so and gate-syms.o
alpha: make short build log available for division routines
alpha: merge build rules of division routines
alpha: add $(src)/ rather than $(obj)/ to make source file path
Makefile: evaluate LDFLAGS_BUILD_ID only once
objtool: make it visible in make V=1 output
kbuild: clang: add -no-integrated-as to KBUILD_[AC]FLAGS
kbuild: Add support to generate LLVM assembly files
kbuild: Add better clang cross build support
kbuild: drop -Wno-unknown-warning-option from clang options
kbuild: fix asm-offset generation to work with clang
kbuild: consolidate redundant sed script ASM offset generation
frv: Use OFFSET macro in DEF_*REG()
kbuild: avoid conflict between -ffunction-sections and -pg on gcc-4.7
kbuild: Consolidate header generation from ASM offset information
kbuild: use -Oz instead of -Os when using clang
kbuild, LLVMLinux: Add -Werror to cc-option to support clang
Kbuild: make designated_init attribute fatal
kbuild: drop unneeded patterns '.*.orig' and '.*.rej' from distclean
...
|
|
Pull RTC updates from Alexandre Belloni:
"RTC subsystem update:
- Add OF device ID table for i2c drivers
New RTC driver:
- Motorola CPCAP PMIC RTC
RTC driver updates:
- cmos: fix IRQ selection
- ds1307: Add ST m41t0 support
- ds1374: fix watchdog configuration
- sh: Add rza series support"
* tag 'rtc-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (33 commits)
rtc: gemini: add return value validation
rtc: snvs: fix an incorrect check of return value
rtc: ds1374: wdt: Fix stop/start ioctl always returning -EINVAL
rtc: ds1374: wdt: Fix issue with timeout scaling from secs to wdt ticks
rtc: sh: mark PM functions as unused
rtc: hid-sensor-time: remove some dead code
rtc: m41t80: Add proper compatible for rv4162
rtc: ds1307: Add m41t0 to OF device ID table
rtc: ds1307: support m41t0 variant
rtc: cpcap: fix improper use of IRQ_NONE for request_threaded_irq
rtc: cmos: Do not assume irq 8 for rtc when there are no legacy irqs
x86: i8259: export legacy_pic symbol
dt-bindings: rtc: document the rtc-sh bindings
rtc: sh: add support for rza series
rtc: cpcap: kfreeing devm allocated memory
rtc: wm8350: Remove unused to_wm8350_from_rtc_dev
rtc: cpcap: new rtc driver
dt-bindings: Add vendor prefix for Motorola
rtc: omap: mark PM methods as __maybe_unused
rtc: omap: remove incorrect __exit markups
...
|
|
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
|
|
NAND branches are now hosted on MTD repos, nand/next is on l2-mtd and
nand/fixes will be on linux-mtd.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Brian: added branch names]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
This patch updates the binding documentation in accordance with
commit 44dd182861f99 ("mtd: nand: gpio: make nCE GPIO optional")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
PlayStation 1/2 joypads can be connected directly to the SPI interface.
Signed-off-by: Tomohiro Yoshidomi <sylph23k@gmail.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Pull clk updates from Stephen Boyd:
"Sort of on the quieter side this time, which is probably due more to
me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core,
mostly small non-critical fixes here and there as well as driver
updates for new and existing hardware support.
The biggest things are the TI clk driver rework to lay the groundwork
for clkctrl support in the next merge window and the AmLogic
audio/graphics clk support.
Core:
- clk_possible_parents debugfs file so we know which parents a clk
could possibly have
- Fix to make clk rate change notifiers stop on the first failure
instead of continuing
New Drivers:
- Mediatek MT6797 SoCs
- hi655x PMIC clks
- AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
- Allwinner H5 SoCs and PRCM hardware
Updates:
- Nvidia Tegra T210 cleanups and non-critical fixes
- TI OMAP cleanups in preparation for clkctrl support
- trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
- ZTE zx296718 SoC VGA clks
- Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
- IDT VersaClock 5P49V5935 support
- Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3
support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (151 commits)
clk: x86: pmc-atom: Checking for IS_ERR() instead of NULL
clk: ti: divider: try to fix ti_clk_register_divider
clk: mvebu: Use kcalloc() in two functions
clk: mvebu: Use kcalloc() in of_cpu_clk_setup()
clk: nomadik: Delete error messages for a failed memory allocation in two functions
clk: nomadik: Use seq_puts() in nomadik_src_clk_show()
clk: Improve a size determination in two functions
clk: Replace four seq_printf() calls by seq_putc()
clk: si5351: Delete an error message for a failed memory allocation in si5351_i2c_probe()
clk: si5351: Use devm_kcalloc() in si5351_i2c_probe()
clk: at91: Use kcalloc() in of_at91_clk_pll_get_characteristics()
reset: mediatek: Add MT2701 ethsys reset controller include file
clk: mediatek: add mt2701 ethernet reset
clk: hi6220: Add the hi655x's pmic clock
clk: ti: fix building without legacy omap3
clk: ti: fix linker error with !SOC_OMAP4
clk: hi3620: Fix a typo in one variable name
clk: hi3620: Delete error messages for a failed memory allocation in two functions
clk: hi3620: Use kcalloc() in hi3620_mmc_clk_init()
clk: hisilicon: Delete error messages for failed memory allocations in hisi_clk_init()
...
|
|
Pull nfsd updates from Bruce Fields:
"Another RDMA update from Chuck Lever, and a bunch of miscellaneous
bugfixes"
* tag 'nfsd-4.12' of git://linux-nfs.org/~bfields/linux: (26 commits)
nfsd: Fix up the "supattr_exclcreat" attributes
nfsd: encoders mustn't use unitialized values in error cases
nfsd: fix undefined behavior in nfsd4_layout_verify
lockd: fix lockd shutdown race
NFSv4: Fix callback server shutdown
SUNRPC: Refactor svc_set_num_threads()
NFSv4.x/callback: Create the callback service through svc_create_pooled
lockd: remove redundant check on block
svcrdma: Clean out old XDR encoders
svcrdma: Remove the req_map cache
svcrdma: Remove unused RDMA Write completion handler
svcrdma: Reduce size of sge array in struct svc_rdma_op_ctxt
svcrdma: Clean up RPC-over-RDMA backchannel reply processing
svcrdma: Report Write/Reply chunk overruns
svcrdma: Clean up RDMA_ERROR path
svcrdma: Use rdma_rw API in RPC reply path
svcrdma: Introduce local rdma_rw API helpers
svcrdma: Clean up svc_rdma_get_inv_rkey()
svcrdma: Add helper to save pages under I/O
svcrdma: Eliminate RPCRDMA_SQ_DEPTH_MULT
...
|
|
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Stable bugfixes:
- Fix use after free in write error path
- Use GFP_NOIO for two allocations in writeback
- Fix a hang in OPEN related to server reboot
- Check the result of nfs4_pnfs_ds_connect
- Fix an rcu lock leak
Features:
- Removal of the unmaintained and unused OSD pNFS layout
- Cleanup and removal of lots of unnecessary dprintk()s
- Cleanup and removal of some memory failure paths now that GFP_NOFS
is guaranteed to never fail.
- Remove the v3-only data server limitation on pNFS/flexfiles
Bugfixes:
- RPC/RDMA connection handling bugfixes
- Copy offload: fixes to ensure the copied data is COMMITed to disk.
- Readdir: switch back to using the ->iterate VFS interface
- File locking fixes from Ben Coddington
- Various use-after-free and deadlock issues in pNFS
- Write path bugfixes"
* tag 'nfs-for-4.12-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (89 commits)
pNFS/flexfiles: Always attempt to call layoutstats when flexfiles is enabled
NFSv4.1: Work around a Linux server bug...
NFS append COMMIT after synchronous COPY
NFSv4: Fix exclusive create attributes encoding
NFSv4: Fix an rcu lock leak
nfs: use kmap/kunmap directly
NFS: always treat the invocation of nfs_getattr as cache hit when noac is on
Fix nfs_client refcounting if kmalloc fails in nfs4_proc_exchange_id and nfs4_proc_async_renew
NFSv4.1: RECLAIM_COMPLETE must handle NFS4ERR_CONN_NOT_BOUND_TO_SESSION
pNFS: Fix NULL dereference in pnfs_generic_alloc_ds_commits
pNFS: Fix a typo in pnfs_generic_alloc_ds_commits
pNFS: Fix a deadlock when coalescing writes and returning the layout
pNFS: Don't clear the layout return info if there are segments to return
pNFS: Ensure we commit the layout if it has been invalidated
pNFS: Don't send COMMITs to the DSes if the server invalidated our layout
pNFS/flexfiles: Fix up the ff_layout_write_pagelist failure path
pNFS: Ensure we check layout validity before marking it for return
NFS4.1 handle interrupted slot reuse from ERR_DELAY
NFSv4: check return value of xdr_inline_decode
nfs/filelayout: fix NULL pointer dereference in fl_pnfs_update_layout()
...
|
|
Pull metag updates from James Hogan:
"These patches primarily make some usercopy improvements (following on
from the recent usercopy fixes):
- reformat and simplify rapf copy loops
- add 64-bit get_user support
And fix a couple more uaccess issues, partily pointed out by Al:
- fix access_ok() serious shortcomings
- fix strncpy_from_user() address validation
Also included is a trivial removal of a redundant increment"
* tag 'metag-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag/mm: Drop pointless increment
metag/uaccess: Check access_ok in strncpy_from_user
metag/uaccess: Fix access_ok()
metag/usercopy: Add 64-bit get_user support
metag/usercopy: Simplify rapf loop fixup corner case
metag/usercopy: Reformat rapf loop inline asm
|
|
Pull virtio updates from Michael Tsirkin:
"Fixes, cleanups, performance
A bunch of changes to virtio, most affecting virtio net. Also ptr_ring
batched zeroing - first of batching enhancements that seems ready."
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
s390/virtio: change maintainership
tools/virtio: fix spelling mistake: "wakeus" -> "wakeups"
virtio_net: tidy a couple debug statements
ptr_ring: support testing different batching sizes
ringtest: support test specific parameters
ptr_ring: batch ring zeroing
virtio: virtio_driver doc
virtio_net: don't reset twice on XDP on/off
virtio_net: fix support for small rings
virtio_net: reduce alignment for buffers
virtio_net: rework mergeable buffer handling
virtio_net: allow specifying context for rx
virtio: allow extra context per descriptor
tools/virtio: fix build breakage
virtio: add context flag to find vqs
virtio: wrap find_vqs
ringtest: fix an assert statement
|
|
If an NFSv4 client asks us for the supattr_exclcreat, then we must
not return attributes that are unsupported by this minor version.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Fixes: 75976de6556f ("NFSD: Return word2 bitmask if setting security..,")
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Pull more KVM updates from Paolo Bonzini:
"ARM:
- bugfixes
- moved shared 32-bit/64-bit files to virt/kvm/arm
- support for saving/restoring virtual ITS state to userspace
PPC:
- XIVE (eXternal Interrupt Virtualization Engine) support
x86:
- nVMX improvements, including emulated page modification logging
(PML) which brings nice performance improvements on some workloads"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (45 commits)
KVM: arm/arm64: vgic-its: Cleanup after failed ITT restore
KVM: arm/arm64: Don't call map_resources when restoring ITS tables
KVM: arm/arm64: Register ITS iodev when setting base address
KVM: arm/arm64: Get rid of its->initialized field
KVM: arm/arm64: Register iodevs when setting redist base and creating VCPUs
KVM: arm/arm64: Slightly rework kvm_vgic_addr
KVM: arm/arm64: Make vgic_v3_check_base more broadly usable
KVM: arm/arm64: Refactor vgic_register_redist_iodevs
KVM: Add kvm_vcpu_get_idx to get vcpu index in kvm->vcpus
nVMX: Advertise PML to L1 hypervisor
nVMX: Implement emulated Page Modification Logging
kvm: x86: Add a hook for arch specific dirty logging emulation
kvm: nVMX: Validate CR3 target count on nested VM-entry
KVM: set no_llseek in stat_fops_per_vm
KVM: arm/arm64: vgic: Rename kvm_vgic_vcpu_init to kvm_vgic_vcpu_enable
KVM: arm/arm64: Clarification and relaxation to ITS save/restore ABI
KVM: arm64: vgic-v3: KVM_DEV_ARM_VGIC_SAVE_PENDING_TABLES
KVM: arm64: vgic-its: Fix pending table sync
KVM: arm64: vgic-its: ITT save and restore
KVM: arm64: vgic-its: Device table save/restore
...
|
|
Pull tracing fix from Steven Rostedt:
"This is a trivial patch that changes a check for a cpumask from a NULL
pointer to using cpumask_available(), which will do the check. This is
because cpumasks when not allocated are always set, and clang
complains about it"
* tag 'trace-v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Use cpumask_available() to check if cpumask variable may be used
|
|
In error cases, lgp->lg_layout_type may be out of bounds; so we
shouldn't be using it until after the check of nfserr.
This was seen to crash nfsd threads when the server receives a LAYOUTGET
request with a large layout type.
GETDEVICEINFO has the same problem.
Reported-by: Ari Kauppi <Ari.Kauppi@synopsys.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Pull TEE driver infrastructure and OP-TEE drivers from Arnd Bergmann:
"This introduces a generic TEE framework in the kernel, to handle
trusted environemtns (security coprocessor or software implementations
such as OP-TEE/TrustZone). I'm sending it separately from the other
arm-soc driver changes to give it a little more visibility, once the
subsystem is merged, we will likely keep this in the armâ‚‹soc drivers
branch or have the maintainers submit pull requests directly,
depending on the patch volume.
I have reviewed earlier versions in the past, and have reviewed the
latest version in person during Linaro Connect BUD17.
Here is my overall assessment of the subsystem:
- There is clearly demand for this, both for the generic
infrastructure and the specific OP-TEE implementation.
- The code has gone through a large number of reviews, and the review
comments have all been addressed, but the reviews were not coming
up with serious issues any more and nobody volunteered to vouch for
the quality.
- The user space ioctl interface is sufficient to work with the
OP-TEE driver, and it should in principle work with other TEE
implementations that follow the GlobalPlatform[1] standards, but it
might need to be extended in minor ways depending on specific
requirements of future TEE implementations
- The main downside of the API to me is how the user space is tied to
the TEE implementation in hardware or firmware, but uses a generic
way to communicate with it. This seems to be an inherent problem
with what it is trying to do, and I could not come up with any
better solution than what is implemented here.
For a detailed history of the patch series, see
https://lkml.org/lkml/2017/3/10/1277"
* tag 'armsoc-tee' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dt: hikey: Add optee node
Documentation: tee subsystem and op-tee driver
tee: add OP-TEE driver
tee: generic TEE subsystem
dt/bindings: add bindings for optee
|
|
Use the new enums for setting and getting the fan control mode.
Fixes problems due to previous inconsistencies between enums.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use the new enums for setting and getting the fan control mode.
Fixes problems due to previous inconsistencies between enums.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use the new enums for setting and getting the fan control mode.
Fixes problems due to previous inconsistencies between enums.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Make the interface consistent.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add common fan enums that can be used for both
powerplay and dpm.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add some new SMU messages.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Pull RCU updates from Ingo Molnar:
"The main changes are:
- Debloat RCU headers
- Parallelize SRCU callback handling (plus overlapping patches)
- Improve the performance of Tree SRCU on a CPU-hotplug stress test
- Documentation updates
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (74 commits)
rcu: Open-code the rcu_cblist_n_lazy_cbs() function
rcu: Open-code the rcu_cblist_n_cbs() function
rcu: Open-code the rcu_cblist_empty() function
rcu: Separately compile large rcu_segcblist functions
srcu: Debloat the <linux/rcu_segcblist.h> header
srcu: Adjust default auto-expediting holdoff
srcu: Specify auto-expedite holdoff time
srcu: Expedite first synchronize_srcu() when idle
srcu: Expedited grace periods with reduced memory contention
srcu: Make rcutorture writer stalls print SRCU GP state
srcu: Exact tracking of srcu_data structures containing callbacks
srcu: Make SRCU be built by default
srcu: Fix Kconfig botch when SRCU not selected
rcu: Make non-preemptive schedule be Tasks RCU quiescent state
srcu: Expedite srcu_schedule_cbs_snp() callback invocation
srcu: Parallelize callback handling
kvm: Move srcu_struct fields to end of struct kvm
rcu: Fix typo in PER_RCU_NODE_PERIOD header comment
rcu: Use true/false in assignment to bool
rcu: Use bool value directly
...
|
Ben Skeggs
Linus Torvalds
Michael Heimpold
Christoph Hellwig
Juergen Gross
Florian Fainelli
Tobias Klauser
Nicholas Bellinger
Dan Williams
Vishal Verma
Boris Brezillon
Christophe Leroy
Tomohiro Yoshidomi
Trond Myklebust
J. Bruce Fields
Rex Zhu