| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This reverts commit 90fabae8a2c225c4e4936723c38857887edde5cc.
Patch was applied hastily, revert and let the v2 be reviewed.
Fixes: 90fabae8a2c2 ("sch_cake: Return __NET_XMIT_STOLEN when consuming enqueued skb")
Link: https://lore.kernel.org/all/87wnao2ha3.fsf@toke.dk/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eric Dumazet says:
====================
tcp: tcp challenge ack fixes
syzbot found a typical data-race addressed in the first patch.
While we are at it, second patch makes the global rate limit
per net-ns and disabled by default.
====================
Link: https://lore.kernel.org/r/20220830185656.268523-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Because per host rate limiting has been proven problematic (side channel
attacks can be based on it), per host rate limiting of challenge acks ideally
should be per netns and turned off by default.
This is a long due followup of following commits:
083ae308280d ("tcp: enable per-socket rate limiting of all 'challenge acks'")
f2b2c582e824 ("tcp: mitigate ACK loops for connections as tcp_sock")
75ff39ccc1bd ("tcp: make challenge acks less predictable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jason Baron <jbaron@akamai.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
challenge_timestamp can be read an written by concurrent threads.
This was expected, but we need to annotate the race to avoid potential issues.
Following patch moves challenge_timestamp and challenge_count
to per-netns storage to provide better isolation.
Fixes: 354e4aa391ed ("tcp: RFC 5961 5.2 Blind Data Injection Attack Mitigation")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case the source port cannot be decoded, print the warning only once. This
still brings attention to the user and does not spam the logs at the same time.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220830163448.8921-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IP_UNICAST_IF socket option is used to set the outgoing interface
for outbound packets.
The IP_UNICAST_IF socket option was added as it was needed by the
Wine project, since no other existing option (SO_BINDTODEVICE socket
option, IP_PKTINFO socket option or the bind function) provided the
needed characteristics needed by the IP_UNICAST_IF socket option. [1]
The IP_UNICAST_IF socket option works well for unconnected sockets,
that is, the interface specified by the IP_UNICAST_IF socket option
is taken into consideration in the route lookup process when a packet
is being sent. However, for connected sockets, the outbound interface
is chosen when connecting the socket, and in the route lookup process
which is done when a packet is being sent, the interface specified by
the IP_UNICAST_IF socket option is being ignored.
This inconsistent behavior was reported and discussed in an issue
opened on systemd's GitHub project [2]. Also, a bug report was
submitted in the kernel's bugzilla [3].
To understand the problem in more detail, we can look at what happens
for UDP packets over IPv4 (The same analysis was done separately in
the referenced systemd issue).
When a UDP packet is sent the udp_sendmsg function gets called and
the following happens:
1. The oif member of the struct ipcm_cookie ipc (which stores the
output interface of the packet) is initialized by the ipcm_init_sk
function to inet->sk.sk_bound_dev_if (the device set by the
SO_BINDTODEVICE socket option).
2. If the IP_PKTINFO socket option was set, the oif member gets
overridden by the call to the ip_cmsg_send function.
3. If no output interface was selected yet, the interface specified
by the IP_UNICAST_IF socket option is used.
4. If the socket is connected and no destination address is
specified in the send function, the struct ipcm_cookie ipc is not
taken into consideration and the cached route, that was calculated in
the connect function is being used.
Thus, for a connected socket, the IP_UNICAST_IF sockopt isn't taken
into consideration.
This patch corrects the behavior of the IP_UNICAST_IF socket option
for connect()ed sockets by taking into consideration the
IP_UNICAST_IF sockopt when connecting the socket.
In order to avoid reconnecting the socket, this option is still
ignored when applied on an already connected socket until connect()
is called again by the Richard Gobert.
Change the __ip4_datagram_connect function, which is called during
socket connection, to take into consideration the interface set by
the IP_UNICAST_IF socket option, in a similar way to what is done in
the udp_sendmsg function.
[1] https://lore.kernel.org/netdev/1328685717.4736.4.camel@edumazet-laptop/T/
[2] https://github.com/systemd/systemd/issues/11935#issuecomment-618691018
[3] https://bugzilla.kernel.org/show_bug.cgi?id=210255
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220829111554.GA1771@debian
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
__mkroute_input() uses fib_validate_source() to trigger an icmp redirect.
My understanding is that fib_validate_source() is used to know if the src
address and the gateway address are on the same link. For that,
fib_validate_source() returns 1 (same link) or 0 (not the same network).
__mkroute_input() is the only user of these positive values, all other
callers only look if the returned value is negative.
Since the below patch, fib_validate_source() didn't return anymore 1 when
both addresses are on the same network, because the route lookup returns
RT_SCOPE_LINK instead of RT_SCOPE_HOST. But this is, in fact, right.
Let's adapat the test to return 1 again when both addresses are on the same
link.
CC: stable@vger.kernel.org
Fixes: 747c14307214 ("ip: fix dflt addr selection for connected nexthop")
Reported-by: kernel test robot <yujie.liu@intel.com>
Reported-by: Heng Qi <hengqi@linux.alibaba.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220829100121.3821-1-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Zhengchao Shao says:
====================
net: sched: remove unused variables
The variable "other" is unused, remove it.
====================
Link: https://lore.kernel.org/r/20220830092255.281330-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The variable "other" in the struct red_stats is not used. Remove it.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The variable "other" in the struct choke_sched_data is not used. Remove it.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RX and TX byte/packet statistics in this driver could be overflowed
relatively quickly on a 32-bit platform. Switch these stats to use the
u64_stats infrastructure to avoid this.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220829233901.3429419-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This macro is only used one place, let's inline it instead to save a
line or two.
Cc: Prashant Malani <pmalani@chromium.org>
Cc: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220830225831.2362403-5-swboyd@chromium.org
|
|
Use the standard error pointer macro to shorten the code and simplify.
Cc: Prashant Malani <pmalani@chromium.org>
Cc: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220830225831.2362403-4-swboyd@chromium.org
|
|
The type of 'index' is unsigned long long, which can't possibly be less
than zero. Remove the impossible check.
Cc: Prashant Malani <pmalani@chromium.org>
Cc: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220830225831.2362403-3-swboyd@chromium.org
|
|
We need a newline here to ensure the next printk starts fresh.
Cc: Prashant Malani <pmalani@chromium.org>
Cc: Tzung-Bi Shih <tzungbi@kernel.org>
Fixes: affc804c44c8 ("platform/chrome: cros_typec_switch: Add switch driver")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220830225831.2362403-2-swboyd@chromium.org
|
|
Functions that work on a pointer to virtual memory such as
virt_to_pfn() and users of that function such as
virt_to_page() are supposed to pass a pointer to virtual
memory, ideally a (void *) or other pointer. However since
many architectures implement virt_to_pfn() as a macro,
this function becomes polymorphic and accepts both a
(unsigned long) and a (void *).
If we instead implement a proper virt_to_pfn(void *addr)
function the following happens (occurred on arch/arm):
net/rds/message.c:357:56: warning: passing argument 1
of 'virt_to_pfn' makes pointer from integer without a
cast [-Wint-conversion]
Fix this with an explicit cast.
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: rds-devel@oss.oracle.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220829132001.114858-1-linus.walleij@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Access to registers is guarded by ingenic_tcu_{enable,disable}_regs()
so the stop bit can be cleared before accessing a timer channel, but
those functions did not clear the stop bit on SoCs with a global TCU
clock gate.
Testing on the X1000 has revealed that the stop bits must be cleared
_and_ the global TCU clock must be ungated to access timer registers.
This appears to be the norm on Ingenic SoCs, and is specified in the
documentation for the X1000 and numerous JZ47xx SoCs.
If the stop bit isn't cleared, register writes don't take effect and
the system can be left in a broken state, eg. the watchdog timer may
not run.
The bug probably went unnoticed because stop bits are zeroed when
the SoC is reset, and the kernel does not set them unless a timer
gets disabled at runtime. However, it is possible that a bootloader
or a previous kernel (if using kexec) leaves the stop bits set and
we should not rely on them being cleared.
Fixing this is easy: have ingenic_tcu_{enable,disable}_regs() always
clear the stop bit, regardless of the presence of a global TCU gate.
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Fixes: 4f89e4b8f121 ("clk: ingenic: Add driver for the TCU clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220617122254.738900-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add the reset idx for the t-phy port 1, used as either USB or
PCI-Express (secondary controller) PHY, depending on board-specific
configuration/layout.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220720102817.237483-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add the reset index for USBSIF P1 (T-PHY port 1), used as either USB
or PCI-Express PHY reset.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220720102817.237483-2-angelogioacchino.delregno@collabora.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The pwrmcu is responsible for power management and idle states in SSPM:
on older SoCs this was managed in Linux drivers like sspm/mcupm/eemgpu
but, at least on MT8195, this functionality was transferred to the ATF
firmware.
For this reason, turning off the pwrmcu related clocks from the kernel
will lead to unability to resume the platform after suspend and other
currently unknown PM related side-effects.
Set the PWRMCU and PWRMCU_BUS_H clocks as critical to prevent the
kernel from turning them off, fixing the aforementioned issue.
Fixes: e2edf59dec0b ("clk: mediatek: Add MT8195 infrastructure clock support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220719093316.37253-1-angelogioacchino.delregno@collabora.com
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add the reset idx for PCIe P0, P1, located in infra_ao RST2 registers.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220629105205.173471-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add the reset index for PCIe P0 and P1 (PCIe0, PCIe1) on MT8195.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220629105205.173471-2-angelogioacchino.delregno@collabora.com
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Commit 7dd33764486d ("ARM: davinci: Delete DM644x board files") and commit
b4aed01de486 ("ARM: davinci: Delete DM646x board files") removes the
support for DaVinci DM644x and DM646x boards.
Hence, remove the PLL and PSC clock descriptions for those boards as well.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20220720082934.17741-1-lukas.bulwahn@gmail.com
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Ensure the match happens in the right direction, previously the
destination used was the server, not the NAT host, as the comment
shows the code intended.
Additionally nf_nat_irc uses port 0 as a signal and there's no valid way
it can appear in a DCC message, so consider port 0 also forged.
Fixes: 869f37d8e48f ("[NETFILTER]: nf_conntrack/nf_nat: add IRC helper port")
Signed-off-by: David Leadbeater <dgl@dgl.cx>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
A new Bluetooth device for the Realtek RTW8852AE has been noted.
This device has the following lsusb output:
Bus 001 Device 003: ID 0cb8:c549 Opticis Co., Ltd Bluetooth Radio
The pertinent part of /sys/kernel/debug/usb/devices is as follows:
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cb8 ProdID=c549 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=7392 ProdID=c611 Rev= 2.00
S: Manufacturer=Realtek
S: Product=Edimax Bluetooth Adapter
S: SerialNumber=XXXXXXXXXXXX
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Szabolcs Sipos <labuwx@balfug.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Based on photos available from the FCC, all currently supported RTL8761B
series USB dongles have the same chip: RTL8761BUV.
rtl8761bu is often used to refer to this chip.
rtl8761b sometimes refers to this chip, and other times to its
UART variant (RTL8761BTV).
+----------------+---------+---------+---------------+
| Dongle | USB VID | USB PID | FCC ID |
+----------------+---------+---------+---------------+
| ASUS USB-BT500 | 0x0b05 | 0x190e | MSQ-USBBTJB00 |
| TP-Link UB500 | 0x2357 | 0x0604 | 2AXJ4UB500 |
| EDUP EP-B3519 | | | 2AHRD-EPB3519 |
| EDUP EP-B3536 | | | 2AHRDEP-B3536 |
| UGREEN CM390 | | | 2AQI5-CM390 |
+----------------+---------+---------+---------------+
Signed-off-by: Szabolcs Sipos <labuwx@balfug.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the support ID(0x13D3, 0x3592) to usb_device_id table for
Realtek RTL8852C.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3592 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add RT5120 PMIC power key support.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1660100142-32493-4-git-send-email-u0084500@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
hci_abort_conn() is a wrapper around a number of DISCONNECT and
CREATE_CONN_CANCEL commands that was being invoked from hci_request
request queues, which are now deprecated. There are two versions:
hci_abort_conn() which can be invoked from the hci_event thread, and
hci_abort_conn_sync() which can be invoked within a hci_sync cmd chain.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The HCI_OP_READ_ENC_KEY_SIZE command is converted from using the
deprecated hci_request mechanism to use hci_send_cmd, with an
accompanying hci_cc_read_enc_key_size to handle it's return response.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
anon_vma->degree tracks the combined number of child anon_vmas and VMAs
that use the anon_vma as their ->anon_vma.
anon_vma_clone() then assumes that for any anon_vma attached to
src->anon_vma_chain other than src->anon_vma, it is impossible for it to
be a leaf node of the VMA tree, meaning that for such VMAs ->degree is
elevated by 1 because of a child anon_vma, meaning that if ->degree
equals 1 there are no VMAs that use the anon_vma as their ->anon_vma.
This assumption is wrong because the ->degree optimization leads to leaf
nodes being abandoned on anon_vma_clone() - an existing anon_vma is
reused and no new parent-child relationship is created. So it is
possible to reuse an anon_vma for one VMA while it is still tied to
another VMA.
This is an issue because is_mergeable_anon_vma() and its callers assume
that if two VMAs have the same ->anon_vma, the list of anon_vmas
attached to the VMAs is guaranteed to be the same. When this assumption
is violated, vma_merge() can merge pages into a VMA that is not attached
to the corresponding anon_vma, leading to dangling page->mapping
pointers that will be dereferenced during rmap walks.
Fix it by separately tracking the number of child anon_vmas and the
number of VMAs using the anon_vma as their ->anon_vma.
Fixes: 7a3ef208e662 ("mm: prevent endless growth of anon_vma hierarchy")
Cc: stable@kernel.org
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rtl8152 driver does not disable multicasting when userspace asks
it to. For example:
$ ifconfig eth0 -multicast -allmulti
$ tcpdump -p -i eth0 # will still capture multicast frames
Fix by clearing the device multicast filter table when multicast and
allmulti are both unset.
Tested as follows:
- Set multicast on eth0 network interface
- verify that multicast packets are coming in:
$ tcpdump -p -i eth0
- Clear multicast and allmulti on eth0 network interface
- verify that no more multicast packets are coming in:
$ tcpdump -p -i eth0
Signed-off-by: Sven van Ashbrook <svenva@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20220830045923.net-next.v1.1.I4fee0ac057083d4f848caf0fa3a9fd466fc374a0@changeid
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 27be45700021 ("x86 idle: remove 32-bit-only "no-hlt" parameter,
hlt_works_ok flag") removed no-hlt, but CONFIG_APM still refers to
it. Suggest "idle=poll" instead, based on the commit message:
> If a user wants to avoid HLT, then "idle=poll"
> is much more useful, as it avoids invocation of HLT
> in idle, while "no-hlt" failed to do so.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220713160840.1577569-1-steve@sk2.org
|
|
The APIC supports two modes, legacy APIC (or xAPIC), and Extended APIC
(or x2APIC). X2APIC mode is mostly compatible with legacy APIC, but
it disables the memory-mapped APIC interface in favor of one that uses
MSRs. The APIC mode is controlled by the EXT bit in the APIC MSR.
The MMIO/xAPIC interface has some problems, most notably the APIC LEAK
[1]. This bug allows an attacker to use the APIC MMIO interface to
extract data from the SGX enclave.
Introduce support for a new feature that will allow the BIOS to lock
the APIC in x2APIC mode. If the APIC is locked in x2APIC mode and the
kernel tries to disable the APIC or revert to legacy APIC mode a GP
fault will occur.
Introduce support for a new MSR (IA32_XAPIC_DISABLE_STATUS) and handle
the new locked mode when the LEGACY_XAPIC_DISABLED bit is set by
preventing the kernel from trying to disable the x2APIC.
On platforms with the IA32_XAPIC_DISABLE_STATUS MSR, if SGX or TDX are
enabled the LEGACY_XAPIC_DISABLED will be set by the BIOS. If
legacy APIC is required, then it SGX and TDX need to be disabled in the
BIOS.
[1]: https://aepicleak.com/aepicleak.pdf
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Neelima Krishnan <neelima.krishnan@intel.com>
Link: https://lkml.kernel.org/r/20220816231943.1152579-1-daniel.sneddon@linux.intel.com
|
|
When the GSO splitting feature of sch_cake is enabled, GSO superpackets
will be broken up and the resulting segments enqueued in place of the
original skb. In this case, CAKE calls consume_skb() on the original skb,
but still returns NET_XMIT_SUCCESS. This can confuse parent qdiscs into
assuming the original skb still exists, when it really has been freed. Fix
this by adding the __NET_XMIT_STOLEN flag to the return value in this case.
Fixes: 0c850344d388 ("sch_cake: Conditionally split GSO segments")
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-18231
Link: https://lore.kernel.org/r/20220831092103.442868-1-toke@toke.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add model numbers for client and mobile parts.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20220824175718.232384-1-tony.luck@intel.com
|
|
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220830201457.7984-1-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Hou Tao says:
====================
From: Hou Tao <houtao1@huawei.com>
Hi,
The patchset aims to fix the issues found during investigating the
syzkaller problem reported in [0]. It seems that the concurrent updates
to the same hash-table bucket may fail as shown in patch 1.
Patch 1 uses preempt_disable() to fix the problem for
htab_use_raw_lock() case. For !htab_use_raw_lock() case, the problem is
left to "BPF specific memory allocator" patchset [1] in which
!htab_use_raw_lock() will be removed.
Patch 2 fixes the out-of-bound memory read problem reported in [0]. The
problem has the root cause as patch 1 and it is fixed by handling -EBUSY
from htab_lock_bucket() correctly.
Patch 3 add two cases for hash-table update: one for the reentrancy of
bpf_map_update_elem(), and another one for concurrent updates of the
same hash-table bucket.
Comments are always welcome.
Regards,
Tao
[0]: https://lore.kernel.org/bpf/CACkBjsbuxaR6cv0kXJoVnBfL9ZJXjjoUcMpw_Ogc313jSrg14A@mail.gmail.com/
[1]: https://lore.kernel.org/bpf/20220819214232.18784-1-alexei.starovoitov@gmail.com/
Change Log:
v4:
* rebased on bpf-next
* add htab_update to DENYLIST.s390x
v3: https://lore.kernel.org/bpf/20220829023709.1958204-1-houtao@huaweicloud.com/
* patch 1: update commit message and add Fixes tag
* patch 2: add Fixes tag
* patch 3: elaborate the description of test cases
v2: https://lore.kernel.org/bpf/bd60ef93-1c6a-2db2-557d-b09b92ad22bd@huaweicloud.com/
* Note the fix is for CONFIG_PREEMPT case in commit message and add
Reviewed-by tag for patch 1
* Drop patch "bpf: Allow normally concurrent map updates for !htab_use_raw_lock() case"
v1: https://lore.kernel.org/bpf/20220821033223.2598791-1-houtao@huaweicloud.com/
====================
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
One test demonstrates the reentrancy of hash map update on the same
bucket should fail, and another one shows concureently updates of
the same hash map bucket should succeed and not fail due to
the reentrancy checking for bucket lock.
There is no trampoline support on s390x, so move htab_update to
denylist.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20220831042629.130006-4-houtao@huaweicloud.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
In __htab_map_lookup_and_delete_batch() if htab_lock_bucket() returns
-EBUSY, it will go to next bucket. Going to next bucket may not only
skip the elements in current bucket silently, but also incur
out-of-bound memory access or expose kernel memory to userspace if
current bucket_cnt is greater than bucket_size or zero.
Fixing it by stopping batch operation and returning -EBUSY when
htab_lock_bucket() fails, and the application can retry or skip the busy
batch as needed.
Fixes: 20b6cc34ea74 ("bpf: Avoid hashtab deadlock with map_locked")
Reported-by: Hao Sun <sunhao.th@gmail.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20220831042629.130006-3-houtao@huaweicloud.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
Per-cpu htab->map_locked is used to prohibit the concurrent accesses
from both NMI and non-NMI contexts. But since commit 74d862b682f5
("sched: Make migrate_disable/enable() independent of RT"),
migrate_disable() is also preemptible under CONFIG_PREEMPT case, so now
map_locked also disallows concurrent updates from normal contexts
(e.g. userspace processes) unexpectedly as shown below:
process A process B
htab_map_update_elem()
htab_lock_bucket()
migrate_disable()
/* return 1 */
__this_cpu_inc_return()
/* preempted by B */
htab_map_update_elem()
/* the same bucket as A */
htab_lock_bucket()
migrate_disable()
/* return 2, so lock fails */
__this_cpu_inc_return()
return -EBUSY
A fix that seems feasible is using in_nmi() in htab_lock_bucket() and
only checking the value of map_locked for nmi context. But it will
re-introduce dead-lock on bucket lock if htab_lock_bucket() is re-entered
through non-tracing program (e.g. fentry program).
One cannot use preempt_disable() to fix this issue as htab_use_raw_lock
being false causes the bucket lock to be a spin lock which can sleep and
does not work with preempt_disable().
Therefore, use migrate_disable() when using the spinlock instead of
preempt_disable() and defer fixing concurrent updates to when the kernel
has its own BPF memory allocator.
Fixes: 74d862b682f5 ("sched: Make migrate_disable/enable() independent of RT")
Reviewed-by: Hao Luo <haoluo@google.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20220831042629.130006-2-houtao@huaweicloud.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
Restrict the ucode loading check to avoid frontdoor loading error.
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In order to ensure only documented properties are present, node schemas
must have unevaluatedProperties or additionalProperties set to false
(typically).
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220823145649.3118479-16-robh@kernel.org
|
|
In order to ensure only documented properties are present, node schemas
must have unevaluatedProperties or additionalProperties set to false
(typically).
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220823145649.3118479-15-robh@kernel.org
|
|
This patch adds a test to ensure bpf_setsockopt(TCP_CONGESTION, "not_exist")
will not trigger the kernel module autoload.
Before the fix:
[ 40.535829] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:274
[...]
[ 40.552134] tcp_ca_find_autoload.constprop.0+0xcb/0x200
[ 40.552689] tcp_set_congestion_control+0x99/0x7b0
[ 40.553203] do_tcp_setsockopt+0x3ed/0x2240
[...]
[ 40.556041] __bpf_setsockopt+0x124/0x640
Signed-off-by: Martin KaFai Lau <martin.lau@linux.dev>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220830231953.792412-1-martin.lau@linux.dev
|
|
When bpf prog changes tcp-cc by calling bpf_setsockopt(TCP_CONGESTION),
it should not try to load module which may be a blocking operation.
This details was correct in the v1 [0] but missed by mistake in the
later revision in commit cb388e7ee3a8 ("bpf: net: Change do_tcp_setsockopt()
to use the sockopt's lock_sock() and capable()"). This patch fixes it by
checking the has_current_bpf_ctx().
[0] https://lore.kernel.org/bpf/20220727060921.2373314-1-kafai@fb.com/
Fixes: cb388e7ee3a8 ("bpf: net: Change do_tcp_setsockopt() to use the sockopt's lock_sock() and capable()")
Signed-off-by: Martin KaFai Lau <martin.lau@linux.dev>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220830231946.791504-1-martin.lau@linux.dev
|
|
Fix for intel_guc_slpc_set_min_freq() warn:
inconsistent returns '&slpc->lock'.
v2: Avoid with_intel_runtime_pm with the
internal goto/return. (Ashutosh)
Also standardize the 'ret' if this came from
the efficient setup. And avoid the 'unlikely'.
Fixes: 95ccf312a1e4 ("drm/i915/guc/slpc: Allow SLPC to use efficient frequency")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220830193537.52201-1-rodrigo.vivi@intel.com
|
|
STMPE driver does not require a specific node name anymore, only the
compatible is checked, update binding according to this.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
Jakub Kicinski
Eric Dumazet
Kurt Kanzenbach
Richard Gobert
Nicolas Dichtel
Zhengchao Shao
Robert Hancock
Stephen Boyd
Linus Walleij
Aidan MacDonald
AngeloGioacchino Del Regno
Lukas Bulwahn
David Leadbeater
Larry Finger
Szabolcs Sipos
Max Chou
ChiYuan Huang
Brian Gix
Jann Horn
Sven van Ashbrook
Stephen Kitt
Daniel Sneddon
Toke Høiland-Jørgensen
Tony Luck
Wolfram Sang
Martin KaFai Lau
Hou Tao
Chengming Gui
Rob Herring
Martin KaFai Lau
Rodrigo Vivi
Francesco Dolcini