| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There are some operations that need to be ignored if there is a soft
disconnect in progress. This is to avoid having a pending EP0 transfer in
progress while attempting to stop active transfers and halting the
controller.
There were several instances seen where a soft disconnect was able to occur
during early link negotiation, i.e. bus reset/conndone, which leads to the
conndone handler re-configuring EPs while attempting to halt the
controller, as DEP flags are cleared as part of the soft disconnect path.
ep0out: cmd 'Start New Configuration'
ep0out: cmd 'Set Endpoint Transfer Resource'
ep0in: cmd 'Set Endpoint Transfer Resource'
ep1out: cmd 'Set Endpoint Transfer Resource'
...
event (00030601): Suspend [U3]
event (00000101): Reset [U0]
ep0out: req ffffff87e5c9e100 length 0/0 zsI ==> 0
event (00000201): Connection Done [U0]
ep0out: cmd 'Start New Configuration'
ep0out: cmd 'Set Endpoint Transfer Resource'
In addition, if a soft disconnect occurs, EP0 events are still allowed to
process, however, it will stall/restart during the SETUP phase. The
host is still able to query for the DATA phase, leading to a
xfernotready(DATA) event. Since none of the SETUP transfer parameters are
populated, the xfernotready is treated as a "wrong direction" error,
leading to a duplicate stall/restart routine.
Add the proper softconnect/connected checks in sequences that are
potentially involved during soft disconnect processing.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The xhci_plat_brcm xhci block can enter suspend with clock disabled to save
power and re-enable them on resume. Make use of the XHCI_SUSPEND_RESUME_CLKS
quirk to do so.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-3-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce XHCI_SUSPEND_RESUME_CLKS quirk as a means to suspend and resume
clocks if the hardware is capable of doing so. We assume that clocks will
be needed if the device may wake.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-2-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to spec:
0000 +19.95%
....
1111 -21.68%
45 * (1 + 19.95%) = 53.9775
45 * (1 - 21.68%) = 35.244
Fix MXS_PHY_TX_CAL45_MIN from 30 to 35
Fix MXS_PHY_TX_CAL45_MAX from 55 to 54
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20220829153124.2791210-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to spec:
0000 +19.95%
....
1111 -21.68%
45 * (1 + 19.95%) = 53.9775
45 * (1 - 21.68%) = 35.244
Chanege fsl,tx-cal-45-dn-ohms and fsl,tx-cal-45-dp-ohms range to [35-54]
from [30-55]
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20220829153124.2791210-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently we look up for endpoint in a table and initate urb endpoint
with it. This is unnecessary because the lookup will always result in
endpoint 0.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Khalid Masum <khalid.masum.92@gmail.com>
Link: https://lore.kernel.org/r/20220824203107.14908-1-khalid.masum.92@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_maxpacket() looks up the endpoint number in the pipe which can fail
if the interface or configuration changes before the routine is called.
This is unexpected and may even cause a modulo by zero afterwards.
So use usb_endpoint_maxp() routine which uses the endpoint stored in URB
to get the maxpacket.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Khalid Masum <khalid.masum.92@gmail.com>
Addresses-Coverity: 744857 ("Division or modulo by zero")
Addresses-Coverity: 1487371 ("Division or modulo by zero")
Link: https://lore.kernel.org/r/20220824193813.13129-1-khalid.masum.92@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As follows from #define NAME_TEMPLATE, the procfs code in the RNDIS driver
expects the # of instances to be 3-digit decimal, while the driver calls
ida_simple_get() passing 0 as the 'end' argument which results in actual
max instance # of INT_MAX. Limit the maximum # of RNDIS instances to 1000
which is still a lot! :-)
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/a8180973-3ded-3644-585a-169589a37642@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some platforms make use of VBUS control over PHY which means controller
driver has to access PHY registers to turn on/off VBUS line.This patch
adds support for such platforms in chipidea.
Flag 'CI_HDRC_PHY_VBUS_CONTROL' added to support VBus control feature.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20220822054051.2941282-1-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix grammar and improve readability of chipidea-usb2 text.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Peter Chen <peter.chen@kernel.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220827203217.7837-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
these are only used in one place, a few lines lower
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20220821145745.122587-1-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Delete the rebundant word "also" in comments.
Signed-off-by: Shaomin Deng <dengshaomin@cdjrlc.com>
Link: https://lore.kernel.org/r/20220827153313.5754-1-dengshaomin@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is always unnecessary to initialise statics to 0.
Signed-off-by: Shaomin Deng <dengshaomin@cdjrlc.com>
Link: https://lore.kernel.org/r/20220827153009.4768-1-dengshaomin@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to ensure only documented properties are present, node schemas
must have unevaluatedProperties or additionalProperties set to false
(typically).
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220823145649.3118479-9-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
An incoming Read request causes multiple Read responses. If a user MR to
copy data from is unavailable or responder cannot send a reply, then the
error messages can be printed for each response attempt, resulting in
message overflow.
Link: https://lore.kernel.org/r/20220829071218.1639065-1-matsuda-daisuke@fujitsu.com
Signed-off-by: Daisuke Matsuda <matsuda-daisuke@fujitsu.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
The member variable obj in struct rxe_task is not needed.
So remove it to save memory.
Link: https://lore.kernel.org/r/20220822011615.805603-4-yanjun.zhu@linux.dev
Signed-off-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Reviewed-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
When sock_create_kern in the function rxe_qp_init_req fails,
qp->sk is set to NULL.
Then the function rxe_create_qp will call rxe_qp_do_cleanup
to handle allocated resource.
Before handling qp->sk, this variable should be checked.
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20220822011615.805603-3-yanjun.zhu@linux.dev
Signed-off-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Reviewed-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
When rxe_queue_init in the function rxe_qp_init_req fails,
both qp->req.task.func and qp->req.task.arg are not initialized.
Because of creation of qp fails, the function rxe_create_qp will
call rxe_qp_do_cleanup to handle allocated resource.
Before calling __rxe_do_task, both qp->req.task.func and
qp->req.task.arg should be checked.
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20220822011615.805603-2-yanjun.zhu@linux.dev
Reported-by: syzbot+ab99dc4c6e961eed8b8e@syzkaller.appspotmail.com
Signed-off-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Reviewed-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Various filesystems store POSIX ACLs on the backing store in their uapi
format. Such filesystems need to translate from the uapi POSIX ACL
format into the VFS format during i_op->get_acl(). The VFS provides the
posix_acl_from_xattr() helper for this task.
But the usage of posix_acl_from_xattr() is currently ambiguous. It is
intended to transform from a uapi POSIX ACL to the VFS represenation.
For example, when retrieving POSIX ACLs for permission checking during
lookup or when calling getxattr() to retrieve system.posix_acl_{access,default}.
Calling posix_acl_from_xattr() during i_op->get_acl() will map the raw
{g,u}id values stored as ACL_{GROUP,USER} entries in the uapi POSIX ACL
format into k{g,u}id_t in the filesystem's idmapping and return a struct
posix_acl ready to be returned to the VFS for caching and to perform
permission checks on.
However, posix_acl_from_xattr() is also called during setxattr() for all
filesystems that rely on VFS provides posix_acl_{access,default}_xattr_handler.
The posix_acl_xattr_set() handler which is used for the ->set() method
of posix_acl_{access,default}_xattr_handler uses posix_acl_from_xattr()
to translate from the uapi POSIX ACL format to the VFS format so that it
can be passed to the i_op->set_acl() handler of the filesystem or for
direct caching in case no i_op->set_acl() handler is defined.
During setxattr() the {g,u}id values stored as ACL_{GROUP,USER} entries
in the uapi POSIX ACL format aren't raw {g,u}id values that need to be
mapped according to the filesystem's idmapping. Instead they are {g,u}id
values in the caller's idmapping which have been generated during
posix_acl_fix_xattr_from_user(). In other words, they are k{g,u}id_t
which are passed as raw {g,u}id values abusing the uapi POSIX ACL format
(Please note that this type safety violation has existed since the
introduction of k{g,u}id_t. Please see [1] for more details.).
So when posix_acl_from_xattr() is called in posix_acl_xattr_set() the
filesystem idmapping is completely irrelevant. Instead, we abuse the
initial idmapping to recover the k{g,u}id_t base on the value stored in
raw {g,u}id as ACL_{GROUP,USER} in the uapi POSIX ACL format.
We need to clearly distinguish betweeen these two operations as it is
really easy to confuse for filesystems as can be seen in ntfs3.
In order to do this we factor out make_posix_acl() which takes callbacks
allowing callers to pass dedicated methods to generate the correct
k{g,u}id_t. This is just an internal static helper which is not exposed
to any filesystems but it neatly encapsulates the basic logic of walking
through a uapi POSIX ACL and returning an allocated VFS POSIX ACL with
the correct k{g,u}id_t values.
The posix_acl_from_xattr() helper can then be implemented as a simple
call to make_posix_acl() with callbacks that generate the correct
k{g,u}id_t from the raw {g,u}id values in ACL_{GROUP,USER} entries in
the uapi POSIX ACL format as read from the backing store.
For setxattr() we add a new helper vfs_set_acl_prepare() which has
callbacks to map the POSIX ACLs from the uapi format with the k{g,u}id_t
values stored in raw {g,u}id format in ACL_{GROUP,USER} entries into the
correct k{g,u}id_t values in the filesystem idmapping. In contrast to
posix_acl_from_xattr() the vfs_set_acl_prepare() helper needs to take
the mount idmapping into account. The differences are explained in more
detail in the kernel doc for the new functions.
In follow up patches we will remove all abuses of posix_acl_from_xattr()
for setxattr() operations and replace it with calls to vfs_set_acl_prepare().
The new vfs_set_acl_prepare() helper allows us to deal with the
ambiguity in how the POSI ACL uapi struct stores {g,u}id values
depending on whether this is a getxattr() or setxattr() operation.
This also allows us to remove the posix_acl_setxattr_idmapped_mnt()
helper reducing the abuse of the POSIX ACL uapi format to pass values
that should be distinct types in {g,u}id values stored as
ACL_{GROUP,USER} entries.
The removal of posix_acl_setxattr_idmapped_mnt() in turn allows us to
re-constify the value parameter of vfs_setxattr() which in turn allows
us to avoid the nasty cast from a const void pointer to a non-const void
pointer on ovl_do_setxattr().
Ultimately, the plan is to get rid of the type violations completely and
never pass the values from k{g,u}id_t as raw {g,u}id in ACL_{GROUP,USER}
entries in uapi POSIX ACL format. But that's a longer way to go and this
is a preparatory step.
Link: https://lore.kernel.org/all/20220801145520.1532837-1-brauner@kernel.org [1]
Co-Developed-by: Seth Forshee <sforshee@digitalocean.com>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
Return EOPNOTSUPP when the POSIX ACL version doesn't match and zero if
there are no entries. This will allow us to reuse the helper in
posix_acl_from_xattr(). This change will have no user visible effects.
Fixes: 0c5fd887d2bb ("acl: move idmapped mount fixup into vfs_{g,s}etxattr()")
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Reviewed-by: Seth Forshee (DigitalOcean) <sforshee@kernel.org>>
|
|
The xattr code in ntfs3 is currently a bit confused. For example, it
defines a POSIX ACL i_op->set_acl() method but instead of relying on the
generic POSIX ACL VFS helpers it defines its own set of xattr helpers
with the consequence that i_op->set_acl() is currently dead code.
Switch ntfs3 to rely on the VFS POSIX ACL xattr handlers. Also remove
i_op->{g,s}et_acl() methods from symlink inode operations. Symlinks
don't support xattrs.
This is a preliminary change for the following patches which move
handling idmapped mounts directly in posix_acl_xattr_set().
This survives POSIX ACL xfstests.
Fixes: be71b5cba2e6 ("fs/ntfs3: Add attrib operations")
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Reviewed-by: Seth Forshee (DigitalOcean) <sforshee@kernel.org>>
|
|
This reverts commit 6005a8aecee8afeba826295321a612ab485c230e.
The assertion was intentionally removed in commit 043b8413e8c0 ("net:
devlink: remove redundant rtnl lock assert") and, contrary what is
described in the commit message, the comment reflects that: "Caller must
hold RTNL mutex or reference to dev...".
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20220829121324.3980376-1-vladbu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Petr Machata says:
====================
mlxsw: Configure max LAG ID for Spectrum-4
Amit Cohen writes:
In the device, LAG identifiers are stored in the port group table (PGT).
During initialization, firmware reserves a certain amount of entries at
the beginning of this table for LAG identifiers.
In Spectrum-4, the size of the PGT table did not increase, but the
maximum number of LAG identifiers was doubled, leaving less room for
others entries (e.g., flood entries) that also reside in the PGT.
Therefore, in order to avoid a regression and as long as there is no
explicit requirement to support 256 LAGs, configure the firmware to
allocate the same amount of LAG entries (128) as in Spectrum-{2,3}.
This can be done via the 'max_lag' field in CONFIG_PROFILE command.
Patch set overview:
Patch #1 edits the comment of the existing 'max_lag' field.
Patch #2 adds support for configuring 'max_lag' field via CONFIG_PROFILE
command.
Patch #3 adds an helper function to get the actual 'max_lag' in the
device.
Patch #4 adjusts Spectrum-4 to configure 'max_lag' field.
====================
Link: https://lore.kernel.org/r/cover.1661527928.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Starting from Spectrum-4, the maximum number of LAG IDs can be configured
by software via CONFIG_PROFILE command during driver initialization.
Add a dedicated instance of 'struct mlxsw_config_profile' for Spectrum-4
and set the 'max_lag' field to 128, which is the same amount of LAG entries
as in Spectrum-{2,3}. Without this configuration, firmware reserves 256
(the value of 'cap_max_lag' resource) entries at beginning of PGT table for
LAG identifiers, which means that less entries in PGT will be available.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the driver queries the maximum supported LAG ID from firmware.
This will not be accurate anymore once the driver will configure 'max_lag'
via CONFIG_PROFILE command.
For resource query, firmware returns the maximum LAG ID which is supported
by hardware. Software can configure firmware to do not allocate entries for
all the supported LAGs, and to limit LAG IDs. In this case, the resource
query will not return the actual maximum LAG ID.
Add a helper function for getting this value. In case that 'max_lag' field
was set during initialization, return the value which was used, otherwise,
query firmware for the maximum supported ID.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the device, LAG identifiers are stored in the port group table (PGT).
During initialization, firmware reserves a certain amount of entries at
the beginning of this table for LAG identifiers.
In Spectrum-4, the size of the PGT table did not increase, but the maximum
number of LAG identifiers was doubled, leaving less room for others entries
(e.g., flood entries) that also reside in the PGT.
Therefore, in order to avoid a regression and as long as there is no
explicit requirement to support 256 LAGs, mlxsw driver will configure the
firmware to allocate the same amount of LAG entries (128) as in
Spectrum-{2,3}. This configuration is done using 'max_lag' field in
CONFIG_PROFILE command. Extend 'struct mlxsw_config_profile' to support
'max_lag' field and configure firmware accordingly.
A next patch will adjust Spectrum-4 to configure 'max_lag' field.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Starting from Spectrum-4, the maximum number of LAG IDs can be configured
by software via CONFIG_PROFILE command during driver initialization.
Edit the comment of 'max_lag' field to mention that this field is reserved
in Spectrum-1/2/3 and describe firmware behavior.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Don't just print a warning. Clean up and return an error as well.
Fixes: c8349639324a ("net: lan966x: Add FDMA functionality")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/YwjgDm/SVd5c1tQU@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tlb_dynamic_lb bonding option is compatible with balance-tlb and balance-alb
modes. In order to be consistent with other option documentation, it should
mention both modes not only balance-tlb.
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220826154738.4039-1-ffmancera@riseup.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These error paths return success but they should return -ENOMEM.
Fixes: 01328e23a476 ("mlxsw: minimal: Extend module to port mapping with slot index")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/YwjgwoJ3M7Kdq9VK@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clang warns:
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:481:6: error: variable 'err' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
if (IS_ERR(flow_rule)) {
^~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:489:9: note: uninitialized use occurs here
return err;
^~~
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:481:2: note: remove the 'if' if its condition is always true
if (IS_ERR(flow_rule)) {
^~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:474:9: note: initialize the variable 'err' to silence this warning
int err;
^
= 0
1 error generated.
There is little reason to have the 'goto + error variable' construct in
this function. Get rid of it and just return the PTR_ERR value in the if
statement and 0 at the end.
Fixes: 430e2d5e2a98 ("net/mlx5: E-Switch, Move send to vport meta rule creation")
Link: https://github.com/ClangBuiltLinux/linux/issues/1695
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20220825180607.2707947-1-nathan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When running `ethtool -p` with the old management firmware,
the management firmware resource is not correctly released,
which causes firmware related malfunction: all the access
to management firmware hangs.
It releases the management firmware resource when set id
mode operation is not supported.
Fixes: ccb9bc1dfa44 ("nfp: add 'ethtool --identify' support")
Signed-off-by: Gao Xiao <gao.xiao@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20220829101651.633840-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Stefan Schmidt says:
====================
ieee802154 for net 2022-08-29
- repeated word fix from Jilin Yuan.
- missed return code setting in the cc2520 driver by Li Qiong.
- fixing a potential race in by defering the workqueue destroy
in the adf7242 driver by Lin Ma.
- fixing a long standing problem in the mac802154 rx path to match
corretcly by Miquel Raynal.
* tag 'ieee802154-for-net-2022-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
ieee802154: cc2520: add rc code in cc2520_tx()
net: mac802154: Fix a condition in the receive path
net/ieee802154: fix repeated words in comments
ieee802154/adf7242: defer destroy_workqueue call
====================
Link: https://lore.kernel.org/r/20220829100308.2802578-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Once devlink port is successfully registered, the devlink pointer is not
NULL. Therefore, the check is going to be always true and therefore
pointless. Remove it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Dimitris Michailidis <dmichail@fungible.com>
Link: https://lore.kernel.org/r/20220826110411.1409446-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same GPIO line can be shared by multiple phys for the coma mode pin.
If that is the case then, all the other phys that share the same line
will failed to be probed because the access to the gpio line is not
non-exclusive.
Fix this by making access to the gpio line to be nonexclusive using flag
GPIOD_FLAGS_BIT_NONEXCLUSIVE. This allows all the other PHYs to be
probed.
Fixes: 738871b09250ee ("net: phy: micrel: add coma mode GPIO")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220830064055.2340403-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Arınç ÜNAL says:
====================
completely rework mediatek,mt7530 binding
This patch series brings complete rework of the mediatek,mt7530 binding.
The binding is checked with "make dt_binding_check
DT_SCHEMA_FILES=mediatek,mt7530.yaml".
If anyone knows the GIC bit for interrupt for multi-chip module MT7530 in
MT7623AI SoC, let me know. I'll add it to the examples.
If anyone got a Unielec U7623 or another MT7623AI board, please reach out.
====================
Link: https://lore.kernel.org/r/20220825082301.409450-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the description of the binding.
- Describe the switches, which SoCs they are in, or if they are standalone.
- Explain the various ways of configuring MT7530's port 5.
- Remove phy-mode = "rgmii-txid" from description. Same code path is
followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Define acceptable phy-mode values for the CPU ports of mt7530 and mt7531
switches. Remove relevant information from the description of the binding.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the examples on the binding.
- Add examples which include a wide variation of configurations.
- Make example comments YAML comment instead of DT binding comment.
- Add interrupt controller to the examples. Include header file for
interrupt.
- Change reset line for MT7621 examples.
- Pretty formatting for the examples.
- Change switch reg to 0.
- Change port labels to fit the example, change port 4 label to wan.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
- Add description for reset-gpios.
- Invalidate reset-gpios if mediatek,mcm is used. We cannot use multiple
reset lines at the same time.
- Invalidate mediatek,mcm if the compatible device is mediatek,mt7531.
There is no multi-chip module version of mediatek,mt7531.
- Require mediatek,mcm for mediatek,mt7621 as the compatible string is only
used for the multi-chip module version of MT7530.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the description of mediatek,mcm. mediatek,mcm is not used on MT7623NI.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make trivial changes on the binding.
- Update title to include MT7531 switch.
- Add me as a maintainer. List maintainers in alphabetical order by first
name.
- Add description to compatible strings.
- Stretch descriptions up to the 80 character limit.
- Remove lists for single items.
- Remove requiring reg as it's already required by dsa-port.yaml.
- Define acceptable reg values for the CPU ports.
- Remove quotes from $ref: "dsa.yaml#".
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix wording in comments for the notifications coalescing feature.
Signed-off-by: Alvaro Karsz <alvaro.karsz@solid-run.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20220823073947.14774-1-alvaro.karsz@solid-run.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TCP_FIN_WAIT2 and TCP_LAST_ACK were not handled, the connection is closing
so we can ignore them and avoid printing the "unhandled state"
warning message.
[ 1298.852386] nvmet_tcp: queue 2 unhandled state 5
[ 1298.879112] nvmet_tcp: queue 7 unhandled state 5
[ 1298.884253] nvmet_tcp: queue 8 unhandled state 5
[ 1298.889475] nvmet_tcp: queue 9 unhandled state 5
v2: Do not call nvmet_tcp_schedule_release_queue(), just ignore
the fin_wait2 and last_ack states.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
There's a goto missing in nvmet_setup_auth(), causing a kernel oops
when nvme_auth_extract_key() fails.
Reported-by: Tal Lossos <tallossos@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Lexar NM610 reports bogus eui64 values that appear to be the same across
all drives. Quirk them out so they are not marked as "non globally unique"
duplicates.
Signed-off-by: Shyamin Ayesh <me@shyamin.com>
[patch formatting]
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
With the new PM macros (DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr()), the
compiler has visibility to see that the functions are not used when
!CONFIG_PM and hence, remove the dead code. As such, there's no need
for '__maybe_unused'.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220829131553.690063-11-nuno.sa@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Support feeding VCC through a regulator.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220829131553.690063-10-nuno.sa@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Optionally reset the device during probe.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220829131553.690063-9-nuno.sa@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Just some code cleanup regarding coding style. With the introduction of
the bits.h macros changes in the code are indeed introduced.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220829131553.690063-8-nuno.sa@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
Wesley Cheng
Justin Chen
Frank Li
Khalid Masum
Sergey Shtylyov
Piyush Mehta
Randy Dunlap
Maciej Żenczykowski
Shaomin Deng
Rob Herring
Daisuke Matsuda
Zhu Yanjun
Christian Brauner
Vlad Buslov
Jakub Kicinski
Amit Cohen
Dan Carpenter
Fernando Fernandez Mancera
Nathan Chancellor
Gao Xiao
Jiri Pirko
Horatiu Vultur
Arınç ÜNAL
Alvaro Karsz
Maurizio Lombardi
Hannes Reinecke
Shyamin Ayesh
Nuno Sá