| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The SRv6 End.B6 and End.B6.Encaps behaviors rely on functions
seg6_do_srh_{encap,inline}() to, respectively: i) encapsulate the
packet within an outer IPv6 header with the specified Segment Routing
Header (SRH); ii) insert the specified SRH directly after the IPv6
header of the packet.
This patch removes the initialization of the IPv6 header payload length
from the input_action_end_b6{_encap}() functions, as it is now handled
properly by seg6_do_srh_{encap,inline}() to avoid corruption of the skb
checksum.
Fixes: 140f04c33bbc ("ipv6: sr: implement several seg6local actions")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Support for SRH encapsulation and insertion was introduced with
commit 6c8702c60b88 ("ipv6: sr: add support for SRH encapsulation and
injection with lwtunnels"), through the seg6_do_srh_encap() and
seg6_do_srh_inline() functions, respectively.
The former encapsulates the packet in an outer IPv6 header along with
the SRH, while the latter inserts the SRH between the IPv6 header and
the payload. Then, the headers are initialized/updated according to the
operating mode (i.e., encap/inline).
Finally, the skb checksum is calculated to reflect the changes applied
to the headers.
The IPv6 payload length ('payload_len') is not initialized
within seg6_do_srh_{inline,encap}() but is deferred in seg6_do_srh(), i.e.
the caller of seg6_do_srh_{inline,encap}().
However, this operation invalidates the skb checksum, since the
'payload_len' is updated only after the checksum is evaluated.
To solve this issue, the initialization of the IPv6 payload length is
moved from seg6_do_srh() directly into the seg6_do_srh_{inline,encap}()
functions and before the skb checksum update takes place.
Fixes: 6c8702c60b88 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/all/20220705190727.69d532417be7438b15404ee1@uniroma2.it
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
check_write_begin() will unlock and put the folio when return
non-zero. So we should avoid unlocking and putting it twice in
netfs layer.
Change the way ->check_write_begin() works in the following two ways:
(1) Pass it a pointer to the folio pointer, allowing it to unlock and put
the folio prior to doing the stuff it wants to do, provided it clears
the folio pointer.
(2) Change the return values such that 0 with folio pointer set means
continue, 0 with folio pointer cleared means re-get and all error
codes indicating an error (no special treatment for -EAGAIN).
[ bagasdotme: use Sphinx code text syntax for *foliop pointer ]
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/56423
Link: https://lore.kernel.org/r/cf169f43-8ee7-8697-25da-0204d1b4343e@redhat.com
Co-developed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Backmerging from drm/drm-next for the final fixes that will go
into v5.20.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
Select ARCH_HAS_GCOV_PROFILE_ALL and set GCOV_PROFILE = n inside
arch/xtensa/boot/lib.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Select ARCH_HAS_KCOV and set KCOV_INSTRUMENT = n inside
arch/xtensa/boot/lib.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
The 'pdev' and 'netdev' need to be released in error cases of
iss_net_configure().
Change the return type of iss_net_configure() to void, because it's
not used.
Fixes: 7282bee78798 ("[PATCH] xtensa: Architecture support for Tensilica Xtensa Part 8")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Provide release() callback for the platform device embedded into struct
iss_net_private and registered in the iss_net_configure so that
platform_device_unregister could be called for it.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
There are two per-device lists in the ISS network driver: command line
parameters list and iss_net_private object list. The latter is only used
for duplicate checking in the function iss_net_setup where the former
should have been used.
Drop iss_net_private object list and associated code and use command
line parameters list in the iss_net_setup instead.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
UNTRAIN_RET is not needed in native_irq_return_ldt because RET
untraining has already been done at this point.
In addition, when the RETBleed mitigation is IBPB, UNTRAIN_RET clobbers
several registers (AX, CX, DX) so here it trashes user values which are
in these registers.
Signed-off-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/35b0d50f-12d1-10c3-f5e8-d6c140486d4a@oracle.com
|
|
This symbol is not used outside of bugs.c, so mark it static.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220714072939.71162-1-jiapeng.chong@linux.alibaba.com
|
|
Return boolean values ("true" or "false") instead of 1 or 0 from bool
functions. This fixes the following warnings from coccicheck:
tools/testing/selftests/bpf/progs/test_xdp_noinline.c:407:9-10: WARNING:
return of 0/1 in function 'decap_v4' with return type bool
tools/testing/selftests/bpf/progs/test_xdp_noinline.c:389:9-10: WARNING:
return of 0/1 in function 'decap_v6' with return type bool
tools/testing/selftests/bpf/progs/test_xdp_noinline.c:290:9-10: WARNING:
return of 0/1 in function 'encap_v6' with return type bool
tools/testing/selftests/bpf/progs/test_xdp_noinline.c:264:9-10: WARNING:
return of 0/1 in function 'parse_tcp' with return type bool
tools/testing/selftests/bpf/progs/test_xdp_noinline.c:242:9-10: WARNING:
return of 0/1 in function 'parse_udp' with return type bool
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Suggested-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Linkui Xiao <xiaolinkui@kylinos.cn>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20220714015647.25074-1-xiaolinkui@kylinos.cn
|
|
BPF map name is limited to BPF_OBJ_NAME_LEN.
A map name is defined as being longer than BPF_OBJ_NAME_LEN,
it will be truncated to BPF_OBJ_NAME_LEN when a userspace program
calls libbpf to create the map. A pinned map also generates a path
in the /sys. If the previous program wanted to reuse the map，
it can not get bpf_map by name, because the name of the map is only
partially the same as the name which get from pinned path.
The syscall information below show that map name "process_pinned_map"
is truncated to "process_pinned_".
bpf(BPF_OBJ_GET, {pathname="/sys/fs/bpf/process_pinned_map",
bpf_fd=0, file_flags=0}, 144) = -1 ENOENT (No such file or directory)
bpf(BPF_MAP_CREATE, {map_type=BPF_MAP_TYPE_HASH, key_size=4,
value_size=4,max_entries=1024, map_flags=0, inner_map_fd=0,
map_name="process_pinned_",map_ifindex=0, btf_fd=3, btf_key_type_id=6,
btf_value_type_id=10,btf_vmlinux_value_type_id=0}, 72) = 4
This patch check that if the name of pinned map are the same as the
actual name for the first (BPF_OBJ_NAME_LEN - 1),
bpf map still uses the name which is included in bpf object.
Fixes: 26736eb9a483 ("tools: libbpf: allow map reuse")
Signed-off-by: Anquan Wu <leiqi96@hotmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/OSZP286MB1725CEA1C95C5CB8E7CCC53FB8869@OSZP286MB1725.JPNP286.PROD.OUTLOOK.COM
|
|
The ARRAY_SIZE macro is more compact and more formal in linux source.
Signed-off-by: Linkui Xiao <xiaolinkui@kylinos.cn>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20220712072302.13761-1-xiaolinkui@kylinos.cn
|
|
Link: https://lore.kernel.org/r/165730608687.177165.11815510982277242966.stgit@brunhilda
Reviewed-by: Gerry Morong <gerry.morong@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update copyright to current year.
Link: https://lore.kernel.org/r/165730608177.177165.13184715486635363193.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Allow user to override the default driver timeout for controller ready.
There are some rare configurations which require the driver to wait longer
than the normal 3 minutes for the controller to complete its bootup
sequence and be ready to accept commands from the driver.
The module parameter is:
ctrl_ready_timeout= { 0 | 30-1800 }
and specifies the timeout in seconds for the driver to wait for controller
ready. The valid range is 0 or 30-1800. The default value is 0, which
causes the driver to use a timeout of 180 seconds (3 minutes).
Link: https://lore.kernel.org/r/165730607666.177165.9221211345284471213.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Change removing a LUN using sysfs from an internal driver function
pqi_remove_all_scsi_devices() to using the .slave_destroy entry in the
scsi_host_template.
A LUN can be deleted via sysfs using this syntax:
echo 1 > /sys/block/sdX/device/delete
Link: https://lore.kernel.org/r/165730607154.177165.9723066932202995774.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Allow SMP affinity to be changeable by disabling managed interrupts.
On distributions where the driver is enabled for multi-queue support the
driver utilizes kernel managed interrupts, which automatically distributes
interrupts to all available CPUs and assigns SMP affinity.
On most distributions, the affinity can not be changed by the user.
This change will allow managed interrupts to be disabled by the user via a
module parameter while still allowing multi-queue support to function
properly.
Use the module parameter disable_managed_interrupts=1
Link: https://lore.kernel.org/r/165730606638.177165.12846020942931640329.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Mike McGowen <Mike.McGowen@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Correct a rare stale RAID map access when performing AIO during a RAID
configuration change.
A race condition in the driver could cause it to access a stale RAID map
when a logical volume is reconfigured.
Modify the driver logic to invalidate a RAID map very early when a RAID
configuration change is detected and only switch to a new RAID map after
the driver detects that the RAID map has changed.
Link: https://lore.kernel.org/r/165730606128.177165.7671413443814750829.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Correct a SOP READ and WRITE DMA flags for some requests.
This update corrects DMA direction issues with SCSI commands removed from
the controller's internal lookup table.
Currently, SCSI READ BLOCK LIMITS (0x5) was removed from the controller
lookup table and exposed a DMA direction flag issue.
SCSI READ BLOCK LIMITS was recently removed from our controller lookup
table so the controller uses the respective IU flag field to set the DMA
data direction. Since the DMA direction is incorrect the FW never completes
the request causing a hang.
Some SCSI commands which use SCSI READ BLOCK LIMITS
* sg_map
* mt -f /dev/stX status
After updating controller firmware, users may notice their tape units
failing. This patch resolves the issue.
Also, the AIO path DMA direction is correct.
The DMA direction flag is a day-one bug with no reported BZ.
Fixes: 6c223761eb54 ("smartpqi: initial commit of Microsemi smartpqi driver")
Link: https://lore.kernel.org/r/165730605618.177165.9054223644512926624.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Change method used to detect controller firmware crash during PQI reset.
PQI reset can fail with error -6 if firmware takes > 100ms to complete
reset.
Method used by driver to detect controller firmware crash during PQI was
incorrect in some cases.
Link: https://lore.kernel.org/r/165730605108.177165.1132931838384767071.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add PCI IDs for Lenovo controllers (values in hex):
VID / DID / SVID / SDID
---- ---- ---- ----
Lenovo 4350-8i HBA 9005 / 028f / 1d49 / 0220
Lenovo 4350-16i HBA 9005 / 028f / 1d49 / 0221
Lenovo 5350-8i RAID 9005 / 028f / 1d49 / 0520
Lenovo 5350-8i Internal RAID 9005 / 028f / 1d49 / 0522
Lenovo 9350-8i RAID 9005 / 028f / 1d49 / 0620
Lenovo 9350-8i Internal RAID 9005 / 028f / 1d49 / 0621
Lenovo 9350-16i RAID 9005 / 028f / 1d49 / 0622
Lenovo 9350-16i Internal RAID 9005 / 028f / 1d49 / 0623
Link: https://lore.kernel.org/r/165730604598.177165.9910276232981721083.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Mike McGowen <Mike.McGowen@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add the PCI ID for (values in hex):
VID / DID / SVID / SDID
---- ---- ---- ----
Adaptec SmartHBA 2100-8i-o 9005 / 0285 / 9005 / 0659
Link: https://lore.kernel.org/r/165730604089.177165.17257514581321583667.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Mike McGowen <Mike.McGowen@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fail all outstanding requests after a PCI linkdown.
Block access to device SCSI attributes during the following conditions:
"Cable pull" is called PQI_CTRL_SURPRISE_REMOVAL.
"PCIe Link Down" is called PQI_CTRL_GRACEFUL_REMOVAL.
Block access to device SCSI attributes during and in rare instances when
the controller goes offline.
Either outstanding requests or the access of SCSI attributes post linkdown
can lead to a hang.
Post linkdown, driver does not fail the outstanding requests leading to
long wait time before all the IOs eventually fail.
Also access of the SCSI attributes by host applications can lead to a
system hang.
Link: https://lore.kernel.org/r/165730603578.177165.4699352086827187263.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Sagar Biradar <sagar.biradar@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add driver support for up to 256 LUNs per device.
Update AIO path to pass the appropriate LUN number for base-code to target
the correct LUN.
Update RAID IO path to pass the appropriate LUN number for FW to target the
correct LUN.
Pass the correct LUN number while doing a LUN reset.
Count the outstanding commands based on LUN number. While removing a
Multi-LUN device, wait for all outstanding commands to complete for all
LUNs.
Add Feature bit support.
Link: https://lore.kernel.org/r/165730603067.177165.14016422176841798336.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Kumar Meiyappan <Kumar.Meiyappan@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Insert a minimum 1 millisecond delay after writing to a register before
reading from it.
SIS and PQI registers that can be both written to and read from can return
stale data if read from too soon after having been written to.
There is no read/write ordering or hazard detection on the inbound path to
the MSGU from the PCIe bus, therefore reads could pass writes.
Link: https://lore.kernel.org/r/165730602555.177165.11181012469428348394.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Signed-off-by: Mike McGowen <mike.mcgowen@microchip.com>
Co-developed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add the following controllers (values in hex):
VID / DID / SVID / SDID
---- / ---- / ---- / ----
Ramaxel FBGF-RAD PM8204 9005 / 028F / 1CC4 / 0101
Ramaxel FBGF-RAD PM8222 9005 / 028F / 1CC4 / 0201
Link: https://lore.kernel.org/r/165730602045.177165.3720208650043407285.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Print controller firmware version to OS message log during driver
initialization or after OFA.
Link: https://lore.kernel.org/r/165730601536.177165.17698744242908911822.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Gilbert Wu <Gilbert.Wu@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Check the response code returned from the LUN reset task management
function and if it indicates the LUN is not valid, do not retry.
Reduce rescan worker delay to 5 seconds for the event handler only.
The removal of a drive from the OS could have been delayed up to 30 seconds
after being physically pulled.
The driver was retrying a LUN reset 3 times even though the return code
indiciated the LUN was no longer valid. There was a 10 second delay between
each retry. Additionally, the rescan worker was scheduled to run 10 seconds
after the driver received the event.
Link: https://lore.kernel.org/r/165730601025.177165.9416869335174437006.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Mike McGowen <Mike.McGowen@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Negotiated link rate needs to be updated to 'Disabled' when phy is stopped.
Link: https://lore.kernel.org/r/20220708205026.969161-1-changyuanl@google.com
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Changyuan Lyu <changyuanl@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, the data flow of the max/min linkrate in the driver is
* in pm8001_get_lrate_mode():
hardcoded value ==> struct sas_phy
* in pm8001_bytes_dmaed():
struct pm8001_phy ==> struct sas_phy
* in pm8001_phy_control():
libsas data ==> struct pm8001_phy
Since pm8001_bytes_dmaed() follows pm8001_get_lrate_mode(), and the fields
in struct pm8001_phy are not initialized, sysfs
`/sys/class/sas_phy/phy-*/maximum_linkrate` always shows `Unknown`.
To fix the issue, change the dataflow to the following:
* in pm8001_phy_init():
initial value ==> struct pm8001_phy
* in pm8001_get_lrate_mode():
struct pm8001_phy ==> struct sas_phy
* in pm8001_phy_control():
libsas data ==> struct pm8001_phy
For negotiated linkrate, the current dataflow is:
* in pm8001_get_lrate_mode():
iomb data ==> struct asd_sas_phy ==> struct sas_phy
* in pm8001_bytes_dmaed():
struct asd_sas_phy ==> struct sas_phy
Since pm8001_bytes_dmaed() follows pm8001_get_lrate_mode(), the assignment
statements in pm8001_bytes_dmaed() are unnecessary and cleaned up.
Link: https://lore.kernel.org/r/20220707175210.528858-1-changyuanl@google.com
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Changyuan Lyu <changyuanl@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In ufshcd_host_reset_and_restore(), ufshcd_set_clk_freq() is called to
scale clock rate. However, this did not call vops->clk_scale_notify() to
inform platform driver of clock change.
Call ufshcd_scale_clks() instead so that clock change can be properly
handled.
Link: https://lore.kernel.org/r/20220711144224.17916-2-powen.kao@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit '3b5f3c0d0548 ("scsi: ufs: core: Tidy up WB configuration code")'
changed the log level of the write boost enable/disable notification from
debug to info. This results in a lot of noise in the kernel log during
normal operation.
Drop it back to debug level to avoid this.
Link: https://lore.kernel.org/r/20220709000027.3929970-1-bjorn.andersson@linaro.org
Fixes: 3b5f3c0d0548 ("scsi: ufs: core: Tidy up WB configuration code")
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Refactor code from fnic probe into a different function so that
scsi layer initialization code is grouped together.
Also, add log messages for better debugging.
Link: https://lore.kernel.org/r/20220707205155.692688-1-kartilak@cisco.com
Co-developed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Signed-off-by: Gian Carlo Boffa <gcboffa@cisco.com>
Co-developed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
DMA masks given in the Zorro ID table don't contain the 2 byte alignment
quirk seen in the GVP11_XFER_MASK macro from gvp11.h so no need to account
for that.
DMA masks passed to dma_set_mask_and_coherent() must be 64 bit, add the
missing cast in the TO_DMA_MASK macro used to convert driver DMA masks to
DMA API masks.
Link: https://lore.kernel.org/r/6d1d88ee-1cf6-c735-1e6d-bafd2096e322@gmail.com
Link: https://lore.kernel.org/r/20220713074913.7873-1-schmitzmic@gmail.com
Fixes: 158da6bcae7a ("scsi: gvp11: Convert m68k WD33C93 drivers to DMA API")
CC: linux-scsi@vger.kernel.org
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Set the maximum time firmware should poll for a link.
If not set firmware could block CPU for a long time resulting
in mailbox failures. If link doesn't come up within 1second,
firmware will anyway notify the status as and when LINK comes up
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha Sowjanya <gakula@marvell.com>
Link: https://lore.kernel.org/r/20220712161815.12621-1-gakula@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-07-12
This series contains updates to ice driver only.
Paul fixes detection of E822 devices for firmware update and changes NVM
read for snapshot creation to be done in chunks as some systems cannot
read the entire NVM in the allotted time.
====================
Link: https://lore.kernel.org/r/20220712164829.7275-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 4db7a2360597 ("scsi: ufs: Fix concurrency of error handler and other
error recovery paths") removed all callers of UIC_HIBERN8_ENTER_RETRIES.
Hence also remove the macro itself.
Link: https://lore.kernel.org/r/20220708052006epcms2p2d1129dbf95fd77f46906200ccb0a9ccd@epcms2p2
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Keoseong Park <keosung.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The megaraid SCSI driver sets set->nr_maps as 3 if poll_queues is > 0, and
blk-mq actually initializes each map's nr_queues as nr_hw_queues.
Consequently the driver has to clear READ queue map's nr_queues, otherwise
the queue map becomes broken if poll_queues is set as non-zero.
Link: https://lore.kernel.org/r/20220706125942.528533-1-ming.lei@redhat.com
Fixes: 9e4bec5b2a23 ("scsi: megaraid_sas: mq_poll support")
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: sumit.saxena@broadcom.com
Cc: chandrakanth.patil@broadcom.com
Cc: linux-block@vger.kernel.org
Cc: Hannes Reinecke <hare@suse.de>
Reported-by: Guangwu Zhang <guazhang@redhat.com>
Tested-by: Guangwu Zhang <guazhang@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since commit 1599069a62c6 ("phy: core: Warn when phy_power_on is called
before phy_init"), the following warning has been reported:
phy_power_on was called before phy_init
To address this, we need to remove phy_power_on from exynos_ufs_phy_init()
and move it after phy_init. phy_power_off and phy_exit are also necessary
in exynos_ufs_remove().
Link: https://lore.kernel.org/r/20220706020255.151177-4-chanho61.park@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use after free is detected by kfence when disabling sriov. What was read
after being freed was vf->pci_dev: it was freed from pci_disable_sriov
and later read in efx_ef10_sriov_free_vf_vports, called from
efx_ef10_sriov_free_vf_vswitching.
Set the pointer to NULL at release time to not trying to read it later.
Reproducer and dmesg log (note that kfence doesn't detect it every time):
$ echo 1 > /sys/class/net/enp65s0f0np0/device/sriov_numvfs
$ echo 0 > /sys/class/net/enp65s0f0np0/device/sriov_numvfs
BUG: KFENCE: use-after-free read in efx_ef10_sriov_free_vf_vswitching+0x82/0x170 [sfc]
Use-after-free read at 0x00000000ff3c1ba5 (in kfence-#224):
efx_ef10_sriov_free_vf_vswitching+0x82/0x170 [sfc]
efx_ef10_pci_sriov_disable+0x38/0x70 [sfc]
efx_pci_sriov_configure+0x24/0x40 [sfc]
sriov_numvfs_store+0xfe/0x140
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x11f/0x1b0
vfs_write+0x1eb/0x280
ksys_write+0x5f/0xe0
do_syscall_64+0x5c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
kfence-#224: 0x00000000edb8ef95-0x00000000671f5ce1, size=2792, cache=kmalloc-4k
allocated by task 6771 on cpu 10 at 3137.860196s:
pci_alloc_dev+0x21/0x60
pci_iov_add_virtfn+0x2a2/0x320
sriov_enable+0x212/0x3e0
efx_ef10_sriov_configure+0x67/0x80 [sfc]
efx_pci_sriov_configure+0x24/0x40 [sfc]
sriov_numvfs_store+0xba/0x140
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x11f/0x1b0
vfs_write+0x1eb/0x280
ksys_write+0x5f/0xe0
do_syscall_64+0x5c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
freed by task 6771 on cpu 12 at 3170.991309s:
device_release+0x34/0x90
kobject_cleanup+0x3a/0x130
pci_iov_remove_virtfn+0xd9/0x120
sriov_disable+0x30/0xe0
efx_ef10_pci_sriov_disable+0x57/0x70 [sfc]
efx_pci_sriov_configure+0x24/0x40 [sfc]
sriov_numvfs_store+0xfe/0x140
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x11f/0x1b0
vfs_write+0x1eb/0x280
ksys_write+0x5f/0xe0
do_syscall_64+0x5c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 3c5eb87605e85 ("sfc: create vports for VFs and assign random MAC addresses")
Reported-by: Yanghang Liu <yanghliu@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20220712062642.6915-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we have a standalone fast path for buffer lookup, we can
easily convert it to use rcu lookups. When we continually hammer the
buffer cache with trylock lookups, we end up with a huge amount of
lock contention on the per-ag buffer hash locks:
- 92.71% 0.05% [kernel] [k] xfs_inodegc_worker
- 92.67% xfs_inodegc_worker
- 92.13% xfs_inode_unlink
- 91.52% xfs_inactive_ifree
- 85.63% xfs_read_agi
- 85.61% xfs_trans_read_buf_map
- 85.59% xfs_buf_read_map
- xfs_buf_get_map
- 85.55% xfs_buf_find
- 72.87% _raw_spin_lock
- do_raw_spin_lock
71.86% __pv_queued_spin_lock_slowpath
- 8.74% xfs_buf_rele
- 7.88% _raw_spin_lock
- 7.88% do_raw_spin_lock
7.63% __pv_queued_spin_lock_slowpath
- 1.70% xfs_buf_trylock
- 1.68% down_trylock
- 1.41% _raw_spin_lock_irqsave
- 1.39% do_raw_spin_lock
__pv_queued_spin_lock_slowpath
- 0.76% _raw_spin_unlock
0.75% do_raw_spin_unlock
This is basically hammering the pag->pag_buf_lock from lots of CPUs
doing trylocks at the same time. Most of the buffer trylock
operations ultimately fail after we've done the lookup, so we're
really hammering the buf hash lock whilst making no progress.
We can also see significant spinlock traffic on the same lock just
under normal operation when lots of tasks are accessing metadata
from the same AG, so let's avoid all this by converting the lookup
fast path to leverages the rhashtable's ability to do rcu protected
lookups.
We avoid races with the buffer release path by using
atomic_inc_not_zero() on the buffer hold count. Any buffer that is
in the LRU will have a non-zero count, thereby allowing the lockless
fast path to be taken in most cache hit situations. If the buffer
hold count is zero, then it is likely going through the release path
so in that case we fall back to the existing lookup miss slow path.
The slow path will then do an atomic lookup and insert under the
buffer hash lock and hence serialise correctly against buffer
release freeing the buffer.
The use of rcu protected lookups means that buffer handles now need
to be freed by RCU callbacks (same as inodes). We still free the
buffer pages before the RCU callback - we won't be trying to access
them at all on a buffer that has zero references - but we need the
buffer handle itself to be present for the entire rcu protected read
side to detect a zero hold count correctly.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
|
|
Currently on the slow path insert we repeat the initial hash table
lookup before we attempt the insert, resulting in a two traversals
of the hash table to ensure the insert is valid. The rhashtable API
provides a method for an atomic lookup and insert operation, so we
can avoid one of the hash table traversals by using this method.
Adapted from a large patch containing this optimisation by Christoph
Hellwig.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
|
|
Avoid an extra atomic operation in the non-trylock case by only
doing a trylock if the XBF_TRYLOCK flag is set. This follows the
pattern in the IO path with NOWAIT semantics where the
"trylock-fail-lock" path showed 5-10% reduced throughput compared to
just using single lock call when not under NOWAIT conditions. So
make that same change here, too.
See commit 942491c9e6d6 ("xfs: fix AIM7 regression") for details.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
[hch: split from a larger patch]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
|
|
Now that we factored xfs_buf_find(), we can start separating into
distinct fast and slow paths from xfs_buf_get_map(). We start by
moving the lookup map and perag setup to _get_map(), and then move
all the specifics of the fast path lookup into xfs_buf_lookup()
and call it directly from _get_map(). We the move all the slow path
code to xfs_buf_find_insert(), which is now also called directly
from _get_map(). As such, xfs_buf_find() now goes away.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
|
|
xfs_buf_find() is made up of three main parts: lookup, insert and
locking. The interactions with xfs_buf_get_map() require it to be
called twice - once for a pure lookup, and again on lookup failure
so the insert path can be run. We want to simplify this down a lot,
so split it into a fast path lookup, a slow path insert and a "lock
the found buffer" helper. This will then let us integrate these
operations more effectively into xfs_buf_get_map() in future
patches.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
|
|
The PN7160 supports error notifications. Add the appropriate callbacks.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220712170011.2990629-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we have a clean operation to update the di_next_unlinked
field of inode cluster buffers, we can easily defer this operation
to transaction commit time so we can order the inode cluster buffer
locking consistently.
To do this, we introduce a new in-memory log item to track the
unlinked list item modification that we are going to make. This
follows the same observations as the in-memory double linked list
used to track unlinked inodes in that the inodes on the list are
pinned in memory and cannot go away, and hence we can simply
reference them for the duration of the transaction without needing
to take active references or pin them or look them up.
This allows us to pass the xfs_inode to the transaction commit code
along with the modification to be made, and then order the logged
modifications via the ->iop_sort and ->iop_precommit operations
for the new log item type. As this is an in-memory log item, it
doesn't have formatting, CIL or AIL operational hooks - it exists
purely to run the inode unlink modifications and is then removed
from the transaction item list and freed once the precommit
operation has run.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
For inodes that are dirty, we have an attached cluster buffer that
we want to use to track the dirty inode through the AIL.
Unfortunately, locking the cluster buffer and adding it to the
transaction when the inode is first logged in a transaction leads to
buffer lock ordering inversions.
The specific problem is ordering against the AGI buffer. When
modifying unlinked lists, the buffer lock order is AGI -> inode
cluster buffer as the AGI buffer lock serialises all access to the
unlinked lists. Unfortunately, functionality like xfs_droplink()
logs the inode before calling xfs_iunlink(), as do various directory
manipulation functions. The inode can be logged way down in the
stack as far as the bmapi routines and hence, without a major
rewrite of lots of APIs there's no way we can avoid the inode being
logged by something until after the AGI has been logged.
As we are going to be using ordered buffers for inode AIL tracking,
there isn't a need to actually lock that buffer against modification
as all the modifications are captured by logging the inode item
itself. Hence we don't actually need to join the cluster buffer into
the transaction until just before it is committed. This means we do
not perturb any of the existing buffer lock orders in transactions,
and the inode cluster buffer is always locked last in a transaction
that doesn't otherwise touch inode cluster buffers.
We do this by introducing a precommit log item method. This commit
just introduces the mechanism; the inode item implementation is in
followup commits.
The precommit items need to be sorted into consistent order as we
may be locking multiple items here. Hence if we have two dirty
inodes in cluster buffers A and B, and some other transaction has
two separate dirty inodes in the same cluster buffers, locking them
in different orders opens us up to ABBA deadlocks. Hence we sort the
items on the transaction based on the presence of a sort log item
method.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
Andrea Mayer
Xiubo Li
Thomas Zimmermann
Max Filippov
Yang Yingliang
Alexandre Chartre
Jiapeng Chong
Linkui Xiao
Anquan Wu
Don Brace
Kevin Barnett
Mike McGowen
Mahesh Rajashekhara
Sagar Biradar
Kumar Meiyappan
Murthy Bhat
Gilbert Wu
Changyuan Lyu
Po-Wen Kao
Bjorn Andersson
Karan Tilak Kumar
Michael Schmitz
Hariprasad Kelam
Jakub Kicinski
Keoseong Park
Ming Lei
Chanho Park
Íñigo Huguet
Dave Chinner
Michael Walle