| Age | Commit message (Collapse) | Author | Files | Lines |
|
Exact match table modification requires wider fields as it has
more number of slots to fill in. Modifying an entry in exact match
table may cause hash collision and may be required to delete entry
from 4-way 2K table and add to fully associative 32 entry CAM table.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There debugfs files created.
1. General information on exact match table
2. Exact match table entries.
3. NPC mcam drop on hit count stats.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NPC exact match table installs drop on hit rules in
NPC mcam for each channel. This rule has broadcast and multicast
bits cleared. Exact match bit cleared and channel bits
set. If exact match table hit bit is 0, corresponding NPC mcam
drop rule will be hit for the packet and will be dropped.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
FLR handler should remove/free all exact match table resources
corresponding to each interface.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
CN10KB silicon supports Exact match feature. This feature can be disabled
through devlink configuration. Devlink command fails if DMAC filter rules
are already present. Once disabled, legacy RPM based DMAC filters will be
configured.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
CN10KB silicon supports exact match table. Scanning KEX
profile should check for exact match feature is enabled
and then set profile masks properly.
These kex profile masks are required to configure NPC
MCAM drop rules. If there is a miss in exact match table,
these drop rules will drop those packets.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
CN10KB silicon has support for exact match table. This table
can be used to match maimum 64 bit value of KPU parsed output.
Hit/non hit in exact match table can be used as a KEX key to
NPC mcam.
This patch makes use of Exact match table to increase number of
DMAC filters supported. NPC mcam is no more need for each of these
DMAC entries as will be populated in Exact match table.
This patch implements following
1. Initialization of exact match table only for CN10KB.
2. Add/del/update interface function for exact match table.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
CN10KB variant of CN10K series of silicons supports
a new feature where in a large protocol field
(eg 128bit IPv6 DIP) can be condensed into a small
hashed 32bit data. This saves a lot of space in MCAM key
and allows user to add more protocol fields into the filter.
A max of two such protocol data can be hashed.
This patch adds support for hashing IPv6 SIP and/or DIP.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use vzalloc() instead of vmalloc() and memset(0) to simpify the code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
In the kernel image vmlinux.lds.S linker scripts the .altinstructions
and __bug_table sections are 4- or 8-byte aligned because they hold 32-
and/or 64-bit values.
Most architectures use altinstructions and BUG() or WARN() in modules as
well, but in the module linker script (module.lds.S) those sections are
currently missing. As consequence the linker will store their content
byte-aligned by default, which then can lead to unnecessary unaligned
memory accesses by the CPU when those tables are processed at runtime.
Usually unaligned memory accesses are unnoticed, because either the
hardware (as on x86 CPUs) or in-kernel exception handlers (e.g. on
parisc or sparc) emulate and fix them up at runtime. Nevertheless, such
unaligned accesses introduce a performance penalty and can even crash
the kernel if there is a bug in the unalignment exception handlers
(which happened once to me on the parisc architecture and which is why I
noticed that issue at all).
This patch fixes a non-critical issue and might be backported at any time.
It's trivial and shouldn't introduce any regression because it simply
tells the linker to use a different (8-byte alignment) for those
sections by default.
Signed-off-by: Helge Deller <deller@gmx.de>
Link: https://lore.kernel.org/all/Yr8%2Fgr8e8I7tVX4d@p100/
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
module_kallsyms_lookup_name() has several exit conditions but
can't return immediately due to preempt_disable().
Refactor module_kallsyms_lookup_name() to allow returning from
anywhere, and reduce depth.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
Checkpatch reports following errors:
ERROR: do not use assignment in if condition
+ if ((colon = strnchr(name, MODULE_NAME_LEN, ':')) != NULL) {
ERROR: do not use assignment in if condition
+ if ((mod = find_module_all(name, colon - name, false)) != NULL)
ERROR: do not use assignment in if condition
+ if ((ret = find_kallsyms_symbol_value(mod, name)) != 0)
ERROR: do not initialise globals to 0
+int modules_disabled = 0;
Fix them.
The following one has to remain, because the condition has to be evaluated
multiple times by the macro wait_event_interruptible_timeout().
ERROR: do not use assignment in if condition
+ if (wait_event_interruptible_timeout(module_wq,
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
Add a module.async_probe kernel command line option that allows enabling
async probing for all modules. When this command line option is used,
there might still be some modules for which we want to explicitly force
synchronous probing, so extend <modulename>.async_probe to take an
optional bool input so that async probing can be disabled for a specific
module.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
The commit 08126db5ff73 ("module: kallsyms: Fix suspicious rcu usage")
under PREEMPT_RT=y, disabling preemption introduced an unbounded
latency since the loop is not fixed. This change caused a regression
since previously preemption was not disabled and we would dereference
RCU-protected pointers explicitly. That being said, these pointers
cannot change.
Before kallsyms-specific data is prepared/or set-up, we ensure that
the unformed module is known to be unique i.e. does not already exist
(see load_module()). Therefore, we can fix this by using the common and
more appropriate RCU flavour as this section of code can be safely
preempted.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Fixes: 08126db5ff73 ("module: kallsyms: Fix suspicious rcu usage")
Signed-off-by: Aaron Tomlin <atomlin@redhat.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
Pull VFIO fix from Alex Williamson:
- Move IOMMU test to unbreak no-iommu support (Jason Gunthorpe)
* tag 'vfio-v5.19-rc7' of https://github.com/awilliam/linux-vfio:
vfio: Move IOMMU_CAP_CACHE_COHERENCY test to after we know we have a group
|
|
As Chris explains, the comment above exit_itimers() is not correct,
we can race with proc_timers_seq_ops. Change exit_itimers() to clear
signal->posix_timers with ->siglock held.
Cc: <stable@vger.kernel.org>
Reported-by: chris@accessvector.net
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In sk_psock_skb_ingress_enqueue function, if the linear area + nr_frags +
frag_list of the SKB has NR_MSG_FRAG_IDS blocks in total, skb_to_sgvec
will return NR_MSG_FRAG_IDS, then msg->sg.end will be set to
NR_MSG_FRAG_IDS, and in addition, (NR_MSG_FRAG_IDS - 1) is set to the last
SG of msg. Recv the msg in sk_msg_recvmsg, when i is (NR_MSG_FRAG_IDS - 1),
the sk_msg_iter_var_next(i) will change i to 0 (not NR_MSG_FRAG_IDS), the
judgment condition "msg_rx->sg.start==msg_rx->sg.end" and
"i != msg_rx->sg.end" can not work.
As a result, the processed msg cannot be deleted from ingress_msg list.
But the length of all the sge of the msg has changed to 0. Then the next
recvmsg syscall will process the msg repeatedly, because the length of sge
is 0, the -EFAULT error is always returned.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220628123616.186950-1-liujian56@huawei.com
|
|
This patch adds the function of headphone button detection,
Button detection will be enabled if the device tree
has a key_enable property.
Signed-off-by: Seven Lee <wtli@nuvoton.com>
Link: https://lore.kernel.org/r/20220627032959.3442064-1-wtli@nuvoton.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Prepare for the BCM63138 ARCH_BCM_63XX migration to ARCH_BCMBCA. Make
SERIAL_BCM63XX depending on ARCH_BCMBCA.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Prepare for the BCM63138 ARCH_BCM_63XX migration to ARCH_BCMBCA. Make
SPI_BCM63XX_HSSPI depending on ARCH_BCMBCA.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Merge series from Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>:
Our tests platforms do use realtek codecs, while implementing avs driver
and machine boards for it, we identified some problems with those codec
drivers.
This series aims to fix those issues.
|
|
- added H616 EMAC compatible
- make pinctrl interrupts optionals in DT binding
- initial H616 DTSI
- added OrangePi Zero 2 board
- added X96 Mate TV box
- add VCC PI supply in pinctrl DT binding
* tag 'sunxi-dt-for-5.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h616: Add X96 Mate TV box support
arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support
dt-bindings: arm: sunxi: Add two H616 board compatible strings
dt-bindings: pinctrl: sunxi: allow vcc-pi-supply
arm64: dts: allwinner: Add Allwinner H616 .dtsi file
dt-bindings: pinctrl: sunxi: Make interrupts optional
dt-bindings: arm: sunxi: Add H616 EMAC0 compatible
Link: https://lore.kernel.org/r/YsnF9cm/qniIOklj@kista.localdomain
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX arm64 device tree update for 5.20:
- Add device tree support for i.MX93 SoC.
- New board device tree: TQMa8MPQL, DH electronics i.MX8M Plus DHCOM and
PDK2, i.MX93 11x11 EVK, phyBOARD-Polis-i.MX8MM.
- A series from Abel Vesa and Viorel Suman to fix i.MX8QXP device tree
to comply with DT schema.
- Disable job ring 0 device for i.MX8MM to avoid caam_jr probe error, due
to that JR0 reservation is done in both upstream (v2.7) and downstream
(NXP lf_v2.4) TF-A.
- A series from Krzysztof Kozlowski to align gpio-key and LED node names
with dtschema.
- Add SNVS LPGPR device for i.MX8MM so that some preserving registers
becomes available as NVMEM.
- Add NoC device support for i.MX8MP SoC.
- A couple of changes from Sean Anderson to add SFP node for TA devices
for LayerScape SoCs.
- A series from Shengjiu Wang to enable bt-sco sound card support for
NXP i.MX8M EVK boards.
- Other small and random board updates.
* tag 'imx-dt64-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (33 commits)
arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP
arm64: dts: freescale: imx8qxp: Fix the keys node name
arm64: dts: freescale: imx8: Fix the system-controller node name
arm64: dts: freescale: imx8qxp: Fix the ocotp node name
arm64: dts: freescale: imx8qxp: Add fallback compatible for clock controller
arm64: dts: freescale: imx8: Fix power controller name
arm64: dts: freescale: imx8qxp: Remove unnecessary clock related entries
arm64: dts: imx8mp: add NoC node
arm64: dts: Add SFP node for TA 3.0 devices
arm64: dts: layerscape: Add SFP node for TA 2.1 devices
arm64: dts: freescale: Add phyBOARD-Polis-i.MX8MM support
arm64: dts: imx8m{m,p}-verdin: use IT temperatures
arm64: dts: imx8mn-evk: add bt-sco sound card support
arm64: dts: imx8mq-evk: add bt-sco sound card support
arm64: dts: imx8mm-evk: add bt-sco sound card support
arm64: freescale/imx8mp-evk.dts: reorder nodes alphabetically
arm64: dts: imx8mq: Pass a label to the AIPS nodes
arm64: dts: imx8m: Pass a label to the soc node
arm64: dts: imx8mm-venice-gw7902: fix UART1 CTS
arm64: dts: imx8mp: Add support for DH electronics i.MX8M Plus DHCOM and PDK2
...
Link: https://lore.kernel.org/r/20220709082951.15123-5-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX device tree change for 5.20:
- A series from Alexander Stein to fix some i.MX6UL dt_binding_check
warnings.
- Replace deprecated 'enable-sdio-wakeup' property with 'wakeup-source'
for a couple of boards.
- A set of imx7-colibri device tree updates from Marcel Ziswiler to
improve devices Display, Touch, Ethernet and SD/MMC, and also adds
Toradex Iris carrier board.
- A few improvements on imx6qdl-colibri board, correct SGTL5000 MCLK
handling, simplify handling of inverted PWM backlight.
- A series from Max Krummenacher (and Oleksandr Suvorov) to improve the
existing i.MX6 Apalis carrier board device trees and adds a new device
tree for the Ixora V1.2 carrier board.
- Add USB dual-role switching using extcon for imx7-colibri board.
- Add SFP node for TA 2.1 devices for LayerScape SoCs.
- Other small and random updates on various boards.
* tag 'imx-dt-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (61 commits)
ARM: dts: layerscape: Add SFP node for TA 2.1 devices
ARM: dts: imx6qdl-prti6q.dtsi: Add applicable properties to usdhc3
ARM: dts: imx6q-bosch-acc: Replace 'enable-sdio-wakeup'
ARM: dts: imx7d-smegw01: Replace 'enable-sdio-wakeup'
ARM: dts: imx6q-apalis: Cleanup
ARM: dts: imx6q-apalis: backlight pwm: Adapt brightness steps
ARM: dts: imx6q-apalis: backlight pwm: Simplify inverted backlight
ARM: dts: imx6q-apalis: Add support for Toradex Ixora V1.2 carrier boards
ARM: dts: imx6q-apalis: Clean-up sd card support
ARM: dts: imx6q-apalis: Add adv7280 video input
ARM: dts: imx6q-apalis: Add ov5640 mipi csi camera
ARM: dts: imx6q-apalis: Disable stmpe touchscreen
ARM: dts: imx6q-apalis: Disable HDMI
ARM: dts: imx6q-apalis: Add LVDS panel support
ARM: dts: imx6q-apalis: move gpio-keys to SoM dtsi
ARM: dts: imx6q-apalis: Move Atmel MXT touch ctrl to SoM dtsi
ARM: dts: imx6q-apalis: Move pinmux groups to SoM dtsi
ARM: dts: imx6q-apalis: Move parallel rgb interface to SoM dtsi
ARM: dts: imx6q-apalis: Command pmic to standby for poweroff
ARM: dts: imx6q-apalis: Add gpio-line-names
...
Link: https://lore.kernel.org/r/20220709082951.15123-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX DT bindings update for 5.20:
- Compatibles for new boards: i.MX7 based Toradex Colibri, DH electronics
i.MX8M Plus DHCOM and PDK2, TQMa8MPxL, Carrier for Toradex i.MX6 Apalis,
i.MX93 EVK, PHYTEC i.MX8MM based board.
- A series from Abel Vesa (and Viorel Suman) to split fsl,scu.txt bindings
into multiple subsystem bindings in yaml format.
- Fix 'line too long' warning caused by Toradex Colibri boards.
* tag 'imx-bindings-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: arm: add TQMa8MPxL board
dt-bindings: firmware: Add fsl,scu yaml file
dt-bindings: watchdog: Add fsl,scu-wdt yaml file
dt-bindings: thermal: Add fsl,scu-thermal yaml file
dt-bindings: rtc: Add fsl,scu-rtc yaml file
dt-bindings: power: Add fsl,scu-pd yaml file
dt-bindings: nvmem: Add fsl,scu-ocotp yaml file
dt-bindings: input: Add fsl,scu-key yaml file
dt-bindings: pinctrl: imx: Add fsl,scu-iomux yaml file
dt-bindings: clk: imx: Add fsl,scu-clk yaml file
bindings: arm: fsl: Add PHYTEC i.MX8MM devicetree bindings
dt-bindings: arm: fsl: Add carrier for toradex,apalis-imx6q
dt-bindings: arm: fsl: Decrease the line length
dt-bindings: arm: Add DH electronics i.MX8M Plus DHCOM and PDK2
dt-bindings: arm: fsl: add toradex,colibri-imx7s/d/d-emmc-iris/-v2
dt-bindings: arm: fsl: add imx93 11x11 evk board
dt-bindings: arm: fsl: correct 1g vs. 1gb in toradex,colibri-imx6ull-*
Link: https://lore.kernel.org/r/20220709082951.15123-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Keystone2 device tree updates for v5.20
* Whitespace cleanups.
* tag 'ti-keystone-dt-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
ARM: dts: keystone: Adjust whitespace around '='
Link: https://lore.kernel.org/r/20220708232709.rrpzbrpv7jbipyym@eldest
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
TI K3 device tree updates for v5.20
* AM62: fixups, sa2ul enabled, ramoops for sk
* others: whitespace and gpio-key cleanup.
* tag 'ti-k3-dt-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
arm64: dts: ti: k3-am62-main: Enable crypto accelerator
arm64: dts: ti: k3-am625-sk: Enable ramoops
arm64: dts: ti: k3-am642-sk: Add pinmux corresponding to main_uart0
arm64: dts: ti: Align gpio-key node names with dtschema
arm64: dts: ti: Adjust whitespace around '='
Link: https://lore.kernel.org/r/20220708232701.vpk45lwogpasaaay@enchilada
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
arm64: tegra: Device tree changes for v5.20-rc1
This adds and enables various hardware on Tegra234 (host1x, VIC, GPCDMA)
as well as the Control BackBone related device tree nodes on Tegra194
and Tegra234.
Native timers are enabled on Tegra186, Tegra194 and Tegra234, which
allow keeping track of SoC-wide timestamps as well as hardware watchdog
functionality.
The audio subsystem is enhanced with the Output Processing Engine (OPE)
on Tegra210 and later.
Finally there are a handful of minor cleanups and fixes.
* tag 'tegra-for-5.20-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix SDMMC1 CD on P2888
arm64: tegra: Update compatible for Tegra234 GPCDMA
arm64: tegra: Add Host1x and VIC on Tegra234
arm64: tegra: Add Host1x context stream IDs on Tegra186+
arm64: tegra: Enable native timers on Tegra234
arm64: tegra: Enable native timers on Tegra194
arm64: tegra: Enable native timers on Tegra186
arm64: tegra: Add node for CBB 2.0 on Tegra234
arm64: tegra: Add node for CBB 1.0 on Tegra194
arm64: tegra: Align gpio-keys node names with dtschema
arm64: tegra: Mark BPMP channels as no-memory-wc
arm64: tegra: Add Tegra234 GPCDMA device tree node
arm64: tegra: Adjust whitespace around '='
arm64: tegra: Enable OPE on various platforms
arm64: tegra: Add OPE device on Tegra210 and later
Link: https://lore.kernel.org/r/20220708185608.676474-7-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
ARM: tegra: Device tree changes for v5.20-rc1
Two minor fixes to help reduce the noise from the DT validation tooling.
* tag 'tegra-for-5.20-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Align gpio-keys node names with dtschema
ARM: tegra: Adjust whitespace around '='
Link: https://lore.kernel.org/r/20220708185608.676474-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
dt-bindings: Changes for v5.20-rc1
These changes add clock, reset, memory client and power domain
definitions for various devices found on Tegra234 along with a few
device tree bindings for new hardware.
* tag 'tegra-for-5.20-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: tegra-ccplex-cluster: Remove status from required properties
dt-bindings: Add headers for Host1x and VIC on Tegra234
dt-bindings: timer: Add Tegra186 & Tegra234 Timer
dt-bindings: arm: tegra: Add NVIDIA Tegra234 CBB 2.0 binding
dt-bindings: arm: tegra: Add NVIDIA Tegra194 AXI2APB binding
dt-bindings: arm: tegra: Add NVIDIA Tegra194 CBB 1.0 binding
dt-bindings: memory: Add Tegra234 MGBE memory clients
dt-bindings: Add Tegra234 MGBE clocks and resets
dt-bindings: power: Add Tegra234 MGBE power domains
dt-bindings: Add headers for Tegra234 GPCDMA
Link: https://lore.kernel.org/r/20220708185608.676474-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
If we encounter some monster sized local-memory page that exceeds the
maximum sg length (UINT32_MAX), ensure that don't end up with some
misaligned address in the entry that follows, leading to fireworks
later. Also ensure we have some coverage of this in the selftests.
v2(Chris):
- Use round_down consistently to avoid udiv errors
v3(Nirmoy):
- Also update the max_segment in the selftest
Fixes: f701b16d4cc5 ("drm/i915/ttm: add i915_sg_from_buddy_resource")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6379
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Nirmoy Das <nirmoy.das@linux.intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220711085859.24198-1-matthew.auld@intel.com
|
|
- whitespace fixes
- replaced RTC indexes with constants
- gpio-key nodes aligned with dtschema
- fixed LED node for Orange Pi Win
- added OPP table for R40 CPU and thermal points
- updated I2C controller compatibles
- added compatibles for MBUS, D1 DE2 clocks, D1 USB
- enable internal HMIC bias on Pinephone
* tag 'sunxi-dt-for-5.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: pinephone: Enable internal HMIC bias
dt-bindings: arm: sunxi: Add several MBUS compatibles
dt-bindings: arm: sunxi: Default to the full MBUS binding
dt-bindings: usb: generic-ohci: Add Allwinner D1 compatible
dt-bindings: usb: generic-ehci: Add Allwinner D1 compatible
dt-bindings: usb: sunxi-musb: Add Allwinner D1 compatible
arm64: dts: allwinner: a100: Update I2C controller fallback
dt-bindings: i2c: mv64xxx: Add variants with offload support
ARM: dts: sun8i-r40: Add thermal trip points/cooling maps
ARM: dts: sun8i-r40: add opp table for cpu
ARM: dts: sun8i-r40: Add "cpu-supply" node for sun8i-r40 based board
arm64: dts: allwinner: a64: orangepi-win: Fix LED node name
dt-bindings: clock: Add compatible for D1 DE2 clocks
ARM: dts: allwinner: align gpio-key node names with dtschema
arm64: dts: allwinner: align gpio-key node names with dtschema
arm64: dts: allwinner: Use constants for RTC clock indexes
ARM: dts: sunxi: Use constants for RTC clock indexes
ARM: dts: sun5i: adjust whitespace around '='
Link: https://lore.kernel.org/r/Ysh8qRH0Q5Xv9Qhf@kista.localdomain
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Merge series from V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com>:
Add Generic driver to support multiple platform,
ADD HS control instance for Rembrandt platform.
Add nau8825,max98560 and rt5682s,rt1019 combination support for legacy
platform.
|
|
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
Two patches to improve error and memory handling. When IPC4 is used,
some of the flows were incorrect.
|
|
We should only have an error when enforcing strict mapping between
kernel and firmware versions. In all other cases, there is no reason
to throw a warning.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220708200719.26961-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove extra space in front of mchp_pdmc_dt_init().
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220711112212.888895-1-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Needed for the Rockchip driver.
|
|
... and cast result to u32 so sparse won't complain anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Sparse tool complains about mixing of different endianess
types, so use the correct ones.
Add type casts where needed.
objdiff shows no changes except in nft_tunnel (type is changed).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Same as the existing ones, no conversions. This is just for sparse sake
only so that we no longer mix be16/u16 and be32/u32 types.
Alternative is to add __force __beX in various places, but this
seems nicer.
objdiff shows no changes.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Switch to be16/32 and u16/32 respectively. No code changes here,
the functions do the same thing, this is just for sparse checkers' sake.
objdiff shows no changes.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Sparse complains because __be32 and u32 are mixed without
conversions. Use the correct types, no code changes.
Furthermore, xt_DSCP generates a bit truncation warning:
"cast truncates bits from constant value (ffffff03 becomes 3)"
The truncation is fine (and wanted). Add a private definition and use that
instead.
objdiff shows no changes.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Sparse flags this as suspicious, because this compares
integer with a be16 with no conversion.
Its a compat check for old userspace that sends host byte order,
so force a be16 cast here.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Change 'succesful' to 'successful'.
Change 'transation' to 'transaction'.
Signed-off-by: Zhang Jiaming <jiaming@nfschina.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
sparse complains about incorrect rcu usage.
Code uses the correct rcu access primitives, but the function pointers
lack rcu annotations.
Collapse all of them into a single structure, then annotate the pointer.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Sparse complains about direct access to the 'helper' and timeout members.
Both have __rcu annotation, so use the accessors.
xt_CT is fine, accesses occur before the structure is visible to other
cpus. Switch to rcu accessors there as well to reduce noise.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Access to the hook pointers use correct helpers but the pointers lack
the needed __rcu annotation.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
To improve hardware offload debuggability count pending 'add', 'del' and
'stats' flow_table offload workqueue tasks. Counters are incremented before
scheduling new task and decremented when workqueue handler finishes
executing. These counters allow user to diagnose congestion on hardware
offload workqueues that can happen when either CPU is starved and workqueue
jobs are executed at lower rate than new ones are added or when
hardware/driver can't keep up with the rate.
Implement the described counters as percpu counters inside new struct
netns_ft which is stored inside struct net. Expose them via new procfs file
'/proc/net/stats/nf_flowtable' that is similar to existing 'nf_conntrack'
file.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Following patches in series use the pointer to access flow table offload
debug variables.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When compiling with -Wformat, clang emits the following warnings:
net/netfilter/nf_conntrack_helper.c:168:18: error: format string is not a string literal (potentially insecure) [-Werror,-Wformat-security]
request_module(mod_name);
^~~~~~~~
Use a string literal for the format string.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Bill Wendling <isanbard@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|