| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Meteor Lake TCSS(Type-C Subsystem) xHCI needs to be runtime suspended
whenever possible to allow the TCSS hardware block to enter D3cold and
thus save energy.
Cc: stable@kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the same way as Intel Alder Lake TCSS (Type-C Subsystem) the Raptor
Lake TCSS xHCI needs to be runtime suspended whenever possible to
allow the TCSS hardware block to enter D3cold and thus save energy.
Cc: stable@kernel.org
Signed-off-by: Tanveer Alam <tanveer1.alam@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
irq is disabled in xhci_quiesce(called by xhci_halt, with bit:2 cleared
in USBCMD register), but xhci_run(called by usb_add_hcd) re-enable it.
It's possible that you will receive thousands of interrupt requests
after initialization for 2.0 roothub. And you will get a lot of
warning like, "xHCI dying, ignoring interrupt. Shouldn't IRQs be
disabled?". This amount of interrupt requests will cause the entire
system to freeze.
This problem was first found on a device with ASM2142 host controller
on it.
[tidy up old code while moving it, reword header -Mathias]
Cc: stable@kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
KVM/arm64 fixes for 5.19, take #2
- Fix a regression with pKVM when kmemleak is enabled
- Add Oliver Upton as an official KVM/arm64 reviewer
|
|
The selftests, when built with newer versions of clang, is found
to have over optimized guests' ucall() function, and eliminating
the stores for uc.cmd (perhaps due to no immediate readers). This
resulted in the userspace side always reading a value of '0', and
causing multiple test failures.
As a result, prevent the compiler from optimizing the stores in
ucall() with WRITE_ONCE().
Suggested-by: Ricardo Koller <ricarkol@google.com>
Suggested-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
Message-Id: <20220615185706.1099208-1-rananta@google.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Johan writes:
USB-serial fixes for 5.19-rc4
Here are some new modem device ids and support for further PL2303
device types.
All but the final commit (RM500K device id) have been in linux-next and
with no reported issues.
* tag 'usb-serial-5.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Quectel RM500K module support
USB: serial: option: add Quectel EM05-G modem
USB: serial: pl2303: add support for more HXN (G) types
USB: serial: option: add Telit LE910Cx 0x1250 composition
|
|
While CONFIG_OF is n but COMPILE_TEST is y, we got this:
WARNING: unmet direct dependencies detected for DRM_DP_AUX_BUS
Depends on [n]: HAS_IOMEM [=y] && DRM [=y] && OF [=n]
Selected by [y]:
- DRM_MSM [=y] && HAS_IOMEM [=y] && DRM [=y] && (ARCH_QCOM || SOC_IMX5 || COMPILE_TEST [=y]) && COMMON_CLK [=y] && IOMMU_SUPPORT [=y] && (QCOM_OCMEM [=n] || QCOM_OCMEM [=n]=n) && (QCOM_LLCC [=y] || QCOM_LLCC [=y]=n) && (QCOM_COMMAND_DB [=n] || QCOM_COMMAND_DB [=n]=n)
Make DRM_DP_AUX_BUS depends on OF || COMPILE_TEST to fix this warning.
Fixes: 1e0f66420b13 ("drm/display: Introduce a DRM display-helper module")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220611041612.1976-1-yuehaibing@huawei.com
|
|
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf and netfilter.
Current release - regressions:
- netfilter: cttimeout: fix slab-out-of-bounds read in
cttimeout_net_exit
Current release - new code bugs:
- bpf: ftrace: keep address offset in ftrace_lookup_symbols
- bpf: force cookies array to follow symbols sorting
Previous releases - regressions:
- ipv4: ping: fix bind address validity check
- tipc: fix use-after-free read in tipc_named_reinit
- eth: veth: add updating of trans_start
Previous releases - always broken:
- sock: redo the psock vs ULP protection check
- netfilter: nf_dup_netdev: fix skb_under_panic
- bpf: fix request_sock leak in sk lookup helpers
- eth: igb: fix a use-after-free issue in igb_clean_tx_ring
- eth: ice: prohibit improper channel config for DCB
- eth: at803x: fix null pointer dereference on AR9331 phy
- eth: virtio_net: fix xdp_rxq_info bug after suspend/resume
Misc:
- eth: hinic: replace memcpy() with direct assignment"
* tag 'net-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
net: openvswitch: fix parsing of nw_proto for IPv6 fragments
sock: redo the psock vs ULP protection check
Revert "net/tls: fix tls_sk_proto_close executed repeatedly"
virtio_net: fix xdp_rxq_info bug after suspend/resume
igb: Make DMA faster when CPU is active on the PCIe link
net: dsa: qca8k: reduce mgmt ethernet timeout
net: dsa: qca8k: reset cpu port on MTU change
MAINTAINERS: Add a maintainer for OCP Time Card
hinic: Replace memcpy() with direct assignment
Revert "drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c"
net: phy: smsc: Disable Energy Detect Power-Down in interrupt mode
ice: ethtool: Prohibit improper channel config for DCB
ice: ethtool: advertise 1000M speeds properly
ice: Fix switchdev rules book keeping
ice: ignore protocol field in GTP offload
netfilter: nf_dup_netdev: add and use recursion counter
netfilter: nf_dup_netdev: do not push mac header a second time
selftests: netfilter: correct PKTGEN_SCRIPT_PATHS in nft_concat_range.sh
net/tls: fix tls_sk_proto_close executed repeatedly
erspan: do not assume transport header is always set
...
|
|
Pull MMC fixes from Ulf Hansson:
- mtk-sd: Fix dma hang issues
- sdhci-pci-o2micro: Fix card detect by dealing with debouncing
* tag 'mmc-v5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mediatek: wait dma stop bit reset to 0
mmc: sdhci-pci-o2micro: Fix card detect by dealing with debouncing
|
|
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 5.19
- fix the mixed up CRIMS/CRWMS constants (Joel Granados)
- add another broken identifier quirk (Leo Savernik)
- fix up a quirk because Samsung reuses PCI IDs over different products
(Christoph Hellwig)"
* tag 'nvme-5.19-2022-06-23' of git://git.infradead.org/nvme:
nvme: move the Samsung X5 quirk entry to the core quirks
nvme: fix the CRIMS and CRWMS definitions to match the spec
nvme: add a bogus subsystem NQN quirk for Micron MTFDKBA2T0TFH
|
|
Since commit 83cbce957446("block: add error handling for device_add_disk /
add_disk"), bdev->bd_holder_dir can not be empty now, so remove WARN_ON()
from bd_link_disk_holder.
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220623074100.2251301-1-linan122@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull sound fixes from Takashi Iwai:
"All small changes, mostly device-specific:
- A regression fix for PCM WC-page allocation on x86
- A regression fix for i915 audio component binding
- Fixes for (longstanding) beep handling bug
- Runtime PM fixes for Intel LPE HDMI audio
- A couple of pending FireWire fixes
- Usual HD-audio and USB-audio quirks, new Intel dspconf entries"
* tag 'sound-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Add quirk for Clevo NS50PU
ALSA: hda: Fix discovery of i915 graphics PCI device
ALSA: hda/via: Fix missing beep setup
ALSA: hda/conexant: Fix missing beep setup
ALSA: memalloc: Drop x86-specific hack for WC allocations
ALSA: hda/realtek: Add quirk for Clevo PD70PNT
ALSA: x86: intel_hdmi_audio: use pm_runtime_resume_and_get()
ALSA: x86: intel_hdmi_audio: enable pm_runtime and set autosuspend delay
ALSA: hda: intel-nhlt: remove use of __func__ in dev_dbg
ALSA: hda: intel-dspcfg: use SOF for UpExtreme and UpExtreme11 boards
firewire: convert sysfs sprintf/snprintf family to sysfs_emit
firewire: cdev: fix potential leak of kernel stack due to uninitialized value
ALSA: hda/realtek: Apply fixup for Lenovo Yoga Duet 7 properly
ALSA: hda/realtek - ALC897 headset MIC no sound
ALSA: usb-audio: US16x08: Move overflow check before array access
ALSA: hda/realtek: Add mute LED quirk for HP Omen laptop
|
|
unmap_grant_pages() currently waits for the pages to no longer be used.
In https://github.com/QubesOS/qubes-issues/issues/7481, this lead to a
deadlock against i915: i915 was waiting for gntdev's MMU notifier to
finish, while gntdev was waiting for i915 to free its pages. I also
believe this is responsible for various deadlocks I have experienced in
the past.
Avoid these problems by making unmap_grant_pages async. This requires
making it return void, as any errors will not be available when the
function returns. Fortunately, the only use of the return value is a
WARN_ON(), which can be replaced by a WARN_ON when the error is
detected. Additionally, a failed call will not prevent further calls
from being made, but this is harmless.
Because unmap_grant_pages is now async, the grant handle will be sent to
INVALID_GRANT_HANDLE too late to prevent multiple unmaps of the same
handle. Instead, a separate bool array is allocated for this purpose.
This wastes memory, but stuffing this information in padding bytes is
too fragile. Furthermore, it is necessary to grab a reference to the
map before making the asynchronous call, and release the reference when
the call returns.
It is also necessary to guard against reentrancy in gntdev_map_put(),
and to handle the case where userspace tries to map a mapping whose
contents have not all been freed yet.
Fixes: 745282256c75 ("xen/gntdev: safely unmap grants in case they are still in use")
Cc: stable@vger.kernel.org
Signed-off-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220622022726.2538-1-demi@invisiblethingslab.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
The third parameter of dma_set_encrypted() is a size in bytes rather than
the number of pages.
Fixes: 4d0564785bb0 ("dma-direct: factor out dma_set_{de,en}crypted helpers")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This device shares the PCI ID with the Samsung 970 Evo Plus that
does not need or want the quirks. Move the the quirk entry to the
core table based on the model number instead.
Fixes: bc360b0b1611 ("nvme-pci: add quirks for Samsung X5 SSDs")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Pankaj Raghav <p.raghav@samsung.com>
|
|
Adjust the values of NVME_CAP_CRMS_CRIMS and NVME_CAP_CRMS_CRWMS masks as
they are different from the ones in TP4084 - Time-to-ready.
Fixes: 354201c53e61 ("nvme: add support for TP4084 - Time-to-Ready Enhancements").
Signed-off-by: Joel Granados <j.granados@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The Micron MTFDKBA2T0TFH device reports the same subsysem NQN for
all devices. Add a quick to ignore it.
Signed-off-by: Leo Savernik <l.savernik@aon.at>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The arm64 support of the generic ARM cpuidle driver was removed. This
let us remove all support code for it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20220529181329.2345722-3-michael@walle.cc
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Since commit 788961462f34 ("ARM: psci: cpuidle: Enable PSCI CPUidle
driver") the generic ARM cpuidle driver doesn't probe anymore because
arm_cpuidle_init() will always return -EOPNOTSUPP. That is, because the
mentioned commit removes the only .cpu_suspend and .cpu_init_idle
provider.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20220529181329.2345722-2-michael@walle.cc
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Add RT5120 PMIC regulator support.
It integrates 4 buck convertes, 1 LDO voltage regulator, 1 external
enable signal to control the external power source.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1655892104-10874-4-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Tidy up the code a little, rather than repeating the check of
mc->autodisable move the stereo error check to be under the
existing if for mc->autodisable.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-6-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
snd_soc_unregister_card() was recently converted to return void. Only
the first instance was adapted, so convert the remaining ones now to fix
building the topology test.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 1892a991886a ("ASoC: core: Make snd_soc_unregister_card() return void")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220622210629.286487-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
bdw_rt286_fe_ops is redundant as platform components already limit the
number of channels available for the endpoint.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-18-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Drop redundant 'ret' assignemnt, stop ignoring set_jack() return value
and reword local 'component' variable to 'codec' to improve readability.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-16-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Print status if setting sysclk fails.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-15-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Declare local 'dev' and make use of it plus dev_get_platdata() to
improve code readability. Relocate few relevant to the function macros
for the exact same read too.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-14-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Drop redundant and update valuable comments within the file to increase
readability. This patch also revisits module information and kconfig
help strings.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-13-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Make use of 100 character limit and modify indentation so code is easier
to read. While at it, sort includes in alphabetical order.
While at it, rename local variable 'chan' to 'channels' to match
hsw_rt5640 board's equivalent.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-12-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Align with other Intel boards naming convention and let the name
explicitly state which components are being connected.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-11-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace ambiguous 'broadwell_rt286_' prefixes in favour of 'card_',
'link_' and other similar strings to clearly state which object given
member implements behavior for.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-10-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rename source file to drop any ambiguity.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-9-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Print status if setting sysclk fails.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-8-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Declare local 'dev' and make use of it plus dev_get_platdata() to
improve code readability.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-7-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Drop redundant and update valuable comments within the file to increase
readability. This patch also revisits module information and kconfig
help strings.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-6-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Make use of 100 character limit and modify indentation so code is easier
to read. While at it, sort includes in alphabetical order.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-5-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Align with other Intel boards naming convention and let the name
explicitly state which components are being connected.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace ambiguous 'haswell_rt5640_' prefixes in favour of 'card_',
'link_' and other similar strings to clearly state which object given
member implements behavior for.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rename source file to drop any ambiguity.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220620101402.2684366-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add usb product id of the Quectel RM500K module.
RM500K provides 2 mandatory interfaces to Linux host after enumeration.
- /dev/ttyUSB5: this is a serial interface for control path. User needs
to write AT commands to this device node to query status, set APN,
set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the
data connection has been established, Linux host can access 5G data
network via this interface.
"RNDIS": RNDIS + ADB + AT (/dev/ttyUSB5) + MODEM COMs
usb-devices output for 0x7001:
T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=7001 Rev=00.01
S: Manufacturer=MediaTek Inc.
S: Product=USB DATA CARD
S: SerialNumber=869206050009672
C: #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Co-developed-by: Ballon Shi <ballon.shi@quectel.com>
Signed-off-by: Ballon Shi <ballon.shi@quectel.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add support for ethtool -p|--identify
by enabling blinking of the panel LED if supported by the NIC firmware.
Signed-off-by: Sixiang Chen <sixiang.chen@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20220622083938.291548-1-simon.horman@corigine.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Before this change nouveau's Kconfig section had 2 "select ACPI_VIDEO"
statements:
select ACPI_VIDEO if ACPI && X86 && BACKLIGHT_CLASS_DEVICE && INPUT
select ACPI_VIDEO if ACPI && X86
Drop the one with the extra conditions, if the conditions for that
one are true then the second statement will always select ACPI_VIDEO
already.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220620094627.9730-1-hdegoede@redhat.com
|
|
When a packet enters the OVS datapath and does not match any existing
flows installed in the kernel flow cache, the packet will be sent to
userspace to be parsed, and a new flow will be created. The kernel and
OVS rely on each other to parse packet fields in the same way so that
packets will be handled properly.
As per the design document linked below, OVS expects all later IPv6
fragments to have nw_proto=44 in the flow key, so they can be correctly
matched on OpenFlow rules. OpenFlow controllers create pipelines based
on this design.
This behavior was changed by the commit in the Fixes tag so that
nw_proto equals the next_header field of the last extension header.
However, there is no counterpart for this change in OVS userspace,
meaning that this field is parsed differently between OVS and the
kernel. This is a problem because OVS creates actions based on what is
parsed in userspace, but the kernel-provided flow key is used as a match
criteria, as described in Documentation/networking/openvswitch.rst. This
leads to issues such as packets incorrectly matching on a flow and thus
the wrong list of actions being applied to the packet. Such changes in
packet parsing cannot be implemented without breaking the userspace.
The offending commit is partially reverted to restore the expected
behavior.
The change technically made sense and there is a good reason that it was
implemented, but it does not comply with the original design of OVS.
If in the future someone wants to implement such a change, then it must
be user-configurable and disabled by default to preserve backwards
compatibility with existing OVS versions.
Cc: stable@vger.kernel.org
Fixes: fa642f08839b ("openvswitch: Derive IP protocol number for IPv6 later frags")
Link: https://docs.openvswitch.org/en/latest/topics/design/#fragments
Signed-off-by: Rosemarie O'Riorden <roriorden@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20220621204845.9721-1-roriorden@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add a warning that this UAPI wasn't such a good idea and shouldn't be
used by anybody.
That should give us a better chance to remove it at some point and
prevents others from running into the same issues.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: T.J. Mercier <tjmercier@google.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220617085702.4298-1-christian.koenig@amd.com
|
|
Fix the missing clk_disable_unprepare() before return
from svs_resume() in the error handling case.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Link: https://lore.kernel.org/r/20220623070240.63382-1-wupeng58@huawei.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-31-krzysztof.kozlowski@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-30-krzysztof.kozlowski@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Commit 8a59f9d1e3d4 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()")
has moved the inet_csk_has_ulp(sk) check from sk_psock_init() to
the new tcp_bpf_update_proto() function. I'm guessing that this
was done to allow creating psocks for non-inet sockets.
Unfortunately the destruction path for psock includes the ULP
unwind, so we need to fail the sk_psock_init() itself.
Otherwise if ULP is already present we'll notice that later,
and call tcp_update_ulp() with the sk_proto of the ULP
itself, which will most likely result in the ULP looping
its callbacks.
Fixes: 8a59f9d1e3d4 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Tested-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/r/20220620191353.1184629-2-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This reverts commit 69135c572d1f84261a6de2a1268513a7e71753e2.
This commit was just papering over the issue, ULP should not
get ->update() called with its own sk_prot. Each ULP would
need to add this check.
Fixes: 69135c572d1f ("net/tls: fix tls_sk_proto_close executed repeatedly")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20220620191353.1184629-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add an entry to the ZynqMP device tree to support the AMS device which
now has a driver in mainline.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Link: https://lore.kernel.org/r/20220120010246.3794962-2-robert.hancock@calian.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
Utkarsh Patel
Tanveer Alam
Mathias Nyman
Hongyu Xie
Paolo Bonzini
Raghavendra Rao Ananta
Greg Kroah-Hartman
YueHaibing
Linus Torvalds
Jens Axboe
Li Nan
Demi Marie Obenour
Dexuan Cui
Christoph Hellwig
Joel Granados
Leo Savernik
Michael Walle
ChiYuan Huang
Charles Keepax
Uwe Kleine-König
Cezary Rojewski
Macpaul Lin
Sixiang Chen
Hans de Goede
Rosemarie O'Riorden
Christian König
Peng Wu
Krzysztof Kozlowski
Jakub Kicinski
Robert Hancock