| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
If no new trace data is available then return immediately, there is no
need to continue with the execution of the trace_read() function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220610080119.30880-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We are using the READ_ONCE() on the debugfs read path for accessing
sdev->host_offset, but the set is not atomic or protected in any way.
Add a small helper to do the host_offset update and be really paranoid
about the a possible race in update
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220610080119.30880-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With the new state we can make sure we are not missing the first
host_offset update.
In case the dtrace is small, the DMA copy will be fast and depending on
the moonphase it might be done before we set the sdev->dtrace_state to
SOF_DTRACE_ENABLED.
The DMA will start the copy as soon as the host starts the DMA. Set the
dtrace to enabled before we let the DMA to run in order to avoid missing
the position update.
The new state is needed to cover architectures where the host side
snd_sof_dma_trace_trigger() is a NOP and the dtrace in the firmware is
ready as soon as the IPC message has been processed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220610080119.30880-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the context save callback to power down the primary core which is used
by the firmware as an indication that the DSP is going to be turned off.
The IMR boot setup is done in response to the primary core power down.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220610083549.16773-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Instead of craft and send an IPC(3) message in hda_dsp_core_get(),
tgl_dsp_core_get() and tgl_dsp_core_put(), use the generic ops for handling
the IPC dependent implementation of core power on/off.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220610083549.16773-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
IPC4 uses the SET_DX message to enable/disable cores managed by the DSP.
The dx_state.core_mask indicates which core is going to change state,
the dx_state.dx_mask is to power on (1) or off (0) the core.
In the dx_mask only those bits (cores) checked which bit is set in the
core_mask, other bits (cores) ignored.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220610083549.16773-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
IPC3 uses sof_ipc_pm_core_config message
(SOF_IPC_GLB_PM_MSG | SOF_IPC_PM_CORE_ENABLE) to enable/disable cores
managed by the DSP.
The core state is set via a single bitfield, if the bit is 1 the core
should be on, if it is 0 then it is off.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220610083549.16773-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a new ops for handling DSP core power state which can be used to tell
the DSP to turn on/off a core (or to inform it that a core is going to be
turned on/off if the core is host managed).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220610083549.16773-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 657774acd00f ("ASoC: SOF: Make sof_suspend/resume IPC agnostic")
did not marked ctx_store and ctx_restore as Optional.
Fixes: 657774acd00f ("ASoC: SOF: Make sof_suspend/resume IPC agnostic")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220610083549.16773-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move the size checks prior to allocating memory as these checks do not need
the data to be allocated and in case of an error we would not need to free
the allocation.
The max size must not be less than the size of
struct sof_ipc_ctrl_data + struct sof_abi_hdr as the ABI header needs to
be present under all circumstances.
The check was incorrectly used or between the two size checks.
Fixes: b5cee8feb1d4 ("ASoC: SOF: topology: Make control parsing IPC agnostic")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220610084735.19397-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently if the APB or Debounce clocks aren't yet ready to be requested
the DW GPIO driver will correctly handle that by deferring the probe
procedure, but the error is still printed to the system log. It needlessly
pollutes the log since there was no real error but a request to postpone
the clock request procedure since the clocks subsystem hasn't been fully
initialized yet. Let's fix that by using the dev_err_probe method to print
the APB/clock request error status. It will correctly handle the deferred
probe situation and print the error if it actually happens.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
When built without OF support, of_match_node() expands to NULL, which
produces the following output:
>> drivers/dma/dw/rzn1-dmamux.c:105:34: warning: unused variable 'rzn1_dmac_match' [-Wunused-const-variable]
static const struct of_device_id rzn1_dmac_match[] = {
One way to silence the warning is to enclose the structure definition
with an #ifdef CONFIG_OF/#endif block.
Fixes: 134d9c52fca2 ("dmaengine: dw: dmamux: Introduce RZN1 DMA router support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220609141455.300879-2-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This is a tristate driver that can be built as a module, as a result,
the OF match table should be exported with MODULE_DEVICE_TABLE().
Fixes: 134d9c52fca2 ("dmaengine: dw: dmamux: Introduce RZN1 DMA router support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220609141455.300879-1-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In the re-init path xhci_resume() passes 'hcd->primary_hcd' to hci_init(),
however this field isn't initialized by __usb_create_hcd() for a HCD
without secondary controller.
xhci_resume() is called once per xHC device, not per hcd, so the extra
checking for primary hcd can be removed.
Fixes: e0fe986972f5 ("usb: host: xhci-plat: prepare operation w/o shared hcd")
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220610115338.863152-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Not all LSR register flags are preserved across reads. Therefore, LSR
readers must store the non-preserved bits into lsr_save_flags.
This fix was initially mixed into feature commit f6f586102add ("serial:
8250: Handle UART without interrupt on TEMT using em485"). However,
that feature change had a flaw and it was reverted to make room for
simpler approach providing the same feature. The embedded fix got
reverted with the feature change.
Re-add the lsr_save_flags fix and properly mark it's a fix.
Link: https://lore.kernel.org/all/1d6c31d-d194-9e6a-ddf9-5f29af829f3@linux.intel.com/T/#m1737eef986bd20cf19593e344cebd7b0244945fc
Fixes: e490c9144cfa ("tty: Add software emulated RS485 support for 8250")
Cc: stable <stable@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@penugtronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/f4d774be-1437-a550-8334-19d8722ab98c@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use n_tty_receive_char_flow_ctrl also on the closing path. This makes
the code cleaner and consistent.
However, there a small change of regression!
The earlier closing path has a small difference compared with the
normal receive path. If START_CHAR and STOP_CHAR are equal, their
precedence is different depending on which path a character is
processed. I don't know whether this difference was intentional or
not, and if equal START_CHAR and STOP_CHAR is actually used anywhere.
But it feels not so useful corner case.
While this change would logically belong to those earlier changes,
having a separate patch for this is useful. If this regresses, bisect
can pinpoint this change rather than the large patch. Also, this
change is not necessary to minimal fix for the issue addressed in
the previous patch.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606153652.63554-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When tty is not read from, XON/XOFF may get stuck into an
intermediate buffer. As those characters are there to do software
flow-control, it is not very useful. In the case where neither end
reads from ttys, the receiving ends might not be able receive the
XOFF characters and just keep sending more data to the opposite
direction. This problem is almost guaranteed to occur with DMA
which sends data in large chunks.
If TTY is slow to process characters, that is, eats less than given
amount in receive_buf, invoke lookahead for the rest of the chars
to process potential XON/XOFF characters.
We need to keep track of how many characters have been processed by the
lookahead to avoid processing the flow control char again on the normal
path. Bookkeeping occurs parallel on two layers (tty_buffer and n_tty)
to avoid passing the lookahead_count through the whole call chain.
When a flow-control char is processed, two things must occur:
a) it must not be treated as normal char
b) if not yet processed, flow-control actions need to be taken
The return value of n_tty_receive_char_flow_ctrl() tells caller a), and
b) is kept internal to n_tty_receive_char_flow_ctrl().
If characters were previous looked ahead, __receive_buf() makes two
calls to the appropriate n_tty_receive_buf_* function. First call is
made with lookahead_done=true for the characters that were subject to
lookahead earlier and then with lookahead=false for the new characters.
Either of the calls might be skipped when it has no characters to
handle.
Reported-by: Gilles Buloz <gilles.buloz@kontron.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606153652.63554-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial core handles serial_rs485 sanitization.
When em485 init fails, there are two possible paths of entry:
1) uart_rs485_config (init path) that fully clears port->rs485 on
error.
2) ioctl path with a pre-existing, valid port->rs485 unto which the
kernel falls back on error and port->rs485 should therefore be
kept untouched. The temporary rs485 struct is not returned to
userspace in case of error so its flag don't matter.
...Thus SER_RS485_ENABLED clearing on error can/should be dropped.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-37-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial core handles serial_rs485 assignment. It is safe to remove this
assignment because sc16is7xx_reg_proc() takes port.lock at start (and
sc16is7xx_reconf_rs485() would too).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-36-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial core handles serial_rs485 assignment.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-35-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial core handles serial_rs485 assignment.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-34-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial core handles serial_rs485 sanitization.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-33-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver provides different rs485_supported for the case where RTS is
not available making it unnecessary to handle it in
imx_uart_rs485_config.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-32-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial core handles serial_rs485 sanitization. Remove custom
sanitization from lpuart_config_rs485.
This change loses dev_err when SER_RS485_RX_DURING_TX is set due to
incorrect configuration. Other drivers do not do similar prinout for
full-duplex case and it should be done in serial core if it is
desirable to notify on this condition. Personally, I doesn't see it
important because the kernel gracefully downgrades to half-duplex.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-31-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial core handles serial_rs485 sanitization.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-30-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial core handles serial_rs485 sanitization and copying rs485 struct.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-29-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial core handles serial_rs485 sanitization and copying rs485 struct.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-28-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial core handles serial_rs485 sanitization and copying rs485 struct.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-27-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial core handles serial_rs485 sanitization and rs485 struct
assignment. As serial_rs485 is already clear for the non-RS485 case by
serial core, there no need to clear flags in the driver.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-26-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to be add new flags more cleanly and safely, return -EINVAL
from TIOCSRS485 ioctl for the flags bits which are not among the
current legacy ones.
This might cause a regression for userspace as those non-flag bits do
not currently trigger -EINVAL. However, it would only occur if the
userspace is sending garbage bits so perhaps we'll get away with this
change.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-25-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When SER_RS485_ENABLED is not set, having any other flag/field set in
serial_rs485 struct does not have an effect different from not having
them set. Thus, make the serial_rs485 struct also match the behavior
for all flags, not just SER_RS485_ENABLED.
Some drivers do similar clearing of rs485 struct in their
rs485_config() already, but not all. This change makes the behavior
consistent across drivers.
Don't try to validate rs485 struct further when no RS485 is requested,
this silences some bogus warnings.
This change has (minor) userspace visible impact.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-24-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Sanitize serial_rs485 struct before calling into rs485_setup. The
drivers provide supported_rs485 to help sanitization of the fields.
If neither of SER_RS485_RTS_ON_SEND or SER_RS485_RTS_AFTER_SEND
supported, don't pretend they can be set to sane settings but clear
them both instead. If only one of them is supported it may look
tempting to use the one driver supports to set the other, however, the
userspace does not have that information readily available so it
wouldn't be helpful.
While adjusting the documentation, remove also the claim that
TIOCGRS485 would call driver specific code. In reality, it does nothing
else than copies the stored serial_rs485 structure from uart_port to
userspace.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-23-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-22-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
This driver does not support delay_rts_after_send but the pre-existing
behavior is to return -EINVAL if delay_rts_after_send is non-zero. In
contrast, other drivers that do not support delay_rts_after_send either
zero delay_rts_after_send or do not care (leave the inaccurate value).
As changing this would cause userspace visible impact, the change is
not attempted here. But perhaps it should be still tried (maybe nobody
finds that kind of API oddity significant)?
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-21-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-20-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-19-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-18-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
In the case where RTS is lacking, RS485 cannot be enabled so provide
zero rs485_supported for that case. Perhaps it would make sense to not
provide rs485_config() at all in that case but such a change would have
userspace visible impact/change in behavior so this patch does not
attempt it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-17-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-16-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-15-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
In the case where RTS is lacking, RS485 cannot be enabled so provide
zero rs485_supported for that case. Perhaps it would make sense to not
provide rs485_config() at all in that case but such a change would have
userspace visible impact/change in behavior so this patch does not
attempt it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-14-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-13-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-12-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
8250_of uses em485, fill in rs485_supported accordingly.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-11-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-10-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
Differentiate based on which port is in question.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features. When the driver is
using em485, take advantage of serial8250_em485_supported.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
bcm2835aux uses em485, fill in rs485_supported accordingly.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Create serial8250_em485_supported for the serial_rs485 features
supported by the em485 framework.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Peter Ujfalusi
Serge Semin
Miquel Raynal
Mathias Nyman
Ilpo Järvinen