| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Instead of always returning -ENOPKG, decode the firmware error
code further when the HWRM_NVM_INSTALL_UPDATE firmware call fails.
Return a more suitable error code to userspace and log an error
in dmesg.
This is version 2 of the earlier patch that was reverted:
02acd399533e ("bnxt_en: parse result field when NVRAM package install fails")
In this new version, if the call is made through devlink instead of
ethtool, we'll also set the error message in extack.
Link: https://lore.kernel.org/netdev/20220307141358.4d52462e@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add driver support to enable timestamping on all RX packets
that are received by the NIC. This capability can be requested
by the applications using SIOCSHWTSTAMP ioctl with filter type
HWTSTAMP_FILTER_ALL.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For correctness, we need to configure the packet filters for timestamping
during bnxt_open. This way they are always configured after firmware
reset or chip reset. We should not assume that the filters will always
be retained across resets.
This patch modifies the ioctl handler and always configures the PTP
filters in the bnxt_open() path.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The main changes are timestamp support for all RX packets and new PCIe
statistics.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The x86 Chromebooks have the ChromeOS ACPI device. This driver attaches
to the ChromeOS ACPI device and exports the values reported by ACPI in a
sysfs directory. This data isn't present in ACPI tables when read
through ACPI tools, hence a driver is needed to do it. The driver gets
data from firmware using the ACPI component of the kernel. The ACPI values
are presented in string form (numbers as decimal values) or binary
blobs, and can be accessed as the contents of the appropriate read only
files in the standard ACPI device's sysfs directory tree. This data is
consumed by the ChromeOS user space.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Co-developed-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/Yn4OKYrtV35Dv+nd@debian-BULLSEYE-live-builder-AMD64
|
|
Add support for low-level debugging on FLEXCOM USART of
LAN966 SoC.
Signed-off-by: Kavyasree Kotagiri <kavyasree.kotagiri@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220513092530.19213-1-kavyasree.kotagiri@microchip.com
|
|
The dmabuf file uses get_next_ino()(through dma_buf_getfile() ->
alloc_anon_inode()) to get an inode number and uses the same as a
directory name under /sys/kernel/dmabuf/buffers/<ino>. This directory is
used to collect the dmabuf stats and it is created through
dma_buf_stats_setup(). At current, failure to create this directory
entry can make the dma_buf_export() to fail.
Now, as the get_next_ino() can definitely give a repetitive inode no
causing the directory entry creation to fail with -EEXIST. This is a
problem on the systems where dmabuf stats functionality is enabled on
the production builds can make the dma_buf_export(), though the dmabuf
memory is allocated successfully, to fail just because it couldn't
create stats entry.
This issue we are able to see on the snapdragon system within 13 days
where there already exists a directory with inode no "122602" so
dma_buf_stats_setup() failed with -EEXIST as it is trying to create
the same directory entry.
To make the dentry name as unique, use the dmabuf fs specific inode
which is based on the simple atomic variable increment. There is tmpfs
subsystem too which relies on its own inode generation rather than
relying on the get_next_ino() for the same reason of avoiding the
duplicate inodes[1].
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/patch/?id=e809d5f0b5c912fe981dce738f3283b2010665f0
Signed-off-by: Charan Teja Kalla <quic_charante@quicinc.com>
Cc: <stable@vger.kernel.org> # 5.15.x+
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1652441296-1986-1-git-send-email-quic_charante@quicinc.com
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
The L1 should not be able to adjust LPES mode for the L2. Setting LPES
if the L0 needs it clear would cause external interrupts to be sent to
L2 and missed by the L0.
Clearing LPES when it may be set, as typically happens with XIVE enabled
could cause a performance issue despite having no native XIVE support in
the guest, because it will cause mediated interrupts for the L2 to be
taken in HV mode, which then have to be injected.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220303053315.1056880-7-npiggin@gmail.com
|
|
The PowerNV L0 currently pushes the OS xive context when running a vCPU,
regardless of whether it is running a nested guest. The problem is that
xive OS ring interrupts will be delivered while the L2 is running.
At the moment, by default, the L2 guest runs with LPCR[LPES]=0, which
actually makes external interrupts go to the L0. That causes the L2 to
exit and the interrupt taken or injected into the L1, so in some
respects this behaves like an escalation. It's not clear if this was
deliberate or not, there's no comment about it and the L1 is actually
allowed to clear LPES in the L2, so it's confusing at best.
When the L2 is running, the L1 is essentially in a ceded state with
respect to external interrupts (it can't respond to them directly and
won't get scheduled again absent some additional event). So the natural
way to solve this is when the L0 handles a H_ENTER_NESTED hypercall to
run the L2, have it arm the escalation interrupt and don't push the L1
context while running the L2.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220303053315.1056880-6-npiggin@gmail.com
|
|
The differences between nested and !nested will become larger in
later changes so split them out for readability.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220303053315.1056880-5-npiggin@gmail.com
|
|
Move the cede abort logic out of xive escalation rearming and into
the caller to prepare for handling a similar case with nested guest
entry.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220303053315.1056880-4-npiggin@gmail.com
|
|
If there is a pending xive interrupt, inject it at guest entry (if
MSR[EE] is enabled) rather than take another interrupt when the guest
is entered. If xive is enabled then LPCR[LPES] is set so this behaviour
should be expected.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220303053315.1056880-3-npiggin@gmail.com
|
|
KVMPPC_NR_LPIDS no longer represents any size restriction on the
LPID space and can be removed. A CPU with more than 12 LPID bits
implemented will now be able to create more than 4095 guests.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220123120043.3586018-7-npiggin@gmail.com
|
|
Rather than tie this to KVMPPC_NR_LPIDS which is becoming more dynamic,
fix it to 4096 (12-bits) explicitly for now.
kvmhv_get_nested() does not have to check against KVM_MAX_NESTED_GUESTS
because the L1 partition table registration hcall already did that, and
it checks against the partition table size.
This patch also puts all the partition table size calculations into the
same form, using 12 for the architected size field shift and 4 for the
shift corresponding to the partition table entry size.
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-of-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220123120043.3586018-6-npiggin@gmail.com
|
|
This removes the fixed sized kvm->arch.nested_guests array.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220123120043.3586018-5-npiggin@gmail.com
|
|
This removes the fixed-size lpid_inuse array.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220123120043.3586018-4-npiggin@gmail.com
|
|
The LPID allocator init is changed to:
- use mmu_lpid_bits rather than hard-coding;
- use KVM_MAX_NESTED_GUESTS for nested hypervisors;
- not reserve the top LPID on POWER9 and newer CPUs.
The reserved LPID is made a POWER7/8-specific detail.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220123120043.3586018-3-npiggin@gmail.com
|
|
Removing kvmppc_claim_lpid makes the lpid allocator API a bit simpler to
change the underlying implementation in a future patch.
The host LPID is always 0, so that can be a detail of the allocator. If
the allocator range is restricted, that can reserve LPIDs at the top of
the range. This allows kvmppc_claim_lpid to be removed.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220123120043.3586018-2-npiggin@gmail.com
|
|
It is better to get all loads for the register values in flight
before starting to switch LPID, PID, and LPCR because those
mtSPRs are expensive and serialising.
This also just tidies up the code for a potential future change
to the context switching sequence.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220123114725.3549202-1-npiggin@gmail.com
|
|
This facility is controlled by FSCR only. Reserved bits should not be
set in the HFSCR register (although it's likely harmless as this
position would not be re-used, and the L0 is forgiving here too).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220122105639.3477407-1-npiggin@gmail.com
|
|
The dt-binding for SCP documents the reg-names order as sram, cfg,
l1tcm. Update the SCP node on the mt8192 devicetree to follow that
order, which gets rid of a dtbs_check warning. This doesn't change any
behavior since the SCP driver accesses the memory regions through the
names anyway.
Fixes: c63556ec6bfe ("arm64: dts: mt8192: Add SCP node")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220504214516.2957504-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
This patch adds a device-tree node for the MTK SPI-NAND Flash Interface
for MT7622 device tree.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20220424032527.673605-6-gch981213@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The UART1 is exposed on a header. Enable the uart1 node to be able to
use it.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20220426134106.242353-8-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
This property doesn't seem to exist in the documentation nor
in source code, let's remove it from the device-tree.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20220426134106.242353-7-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Fix the following dtbs_check error by using the correct node name:
/home/fabo/build/linux/mt8183-pumpkin/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dtb: ntc: $nodename:0: 'ntc' does not match '^thermistor(.*)?$'
From schema: /home/fabo/devel/baylibre/linux-mainline/Documentation/devicetree/bindings/hwmon/ntc-thermistor.yaml
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220426164755.435372-1-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
On an MT7622 system, the kernel complains of not being able to detect the cache
hierarchy of CPU 0. Specify the shared L2 cache node in the device tree, in
order to fix this.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://lore.kernel.org/r/20220428225755.785153-1-rsalvaterra@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The MT7622 device tree never bothered to specify the number of virtual DMA
channels for the HSDMA controller, always falling back to the default value of
3. Make this value explicit, in order to avoid the following dmesg notification:
mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://lore.kernel.org/r/20220429084225.298213-1-rsalvaterra@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
This property doesn't seem to exist in the documentation nor
in source code, but for some reason it is defined in a bunch
of device trees.
Signed-off-by: Dang Huynh <danct12@riseup.net>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220425064850.246228-1-danct12@riseup.net
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
This reverts commits:
0dad4087a86a2cbe177404dc73f18ada26a2c390 ("tcp/dccp: get rid of inet_twsk_purge()")
d507204d3c5cc57d9a8bdf0a477615bb59ea1611 ("tcp/dccp: add tw->tw_bslot")
As Leonard pointed out, a newly allocated netns can happen
to reuse a freed 'struct net'.
While TCP TW timers were covered by my patches, other things were not:
1) Lookups in rx path (INET_MATCH() and INET6_MATCH()), as they look
at 4-tuple plus the 'struct net' pointer.
2) /proc/net/tcp[6] and inet_diag, same reason.
3) hashinfo->bhash[], same reason.
Fixing all this seems risky, lets instead revert.
In the future, we might have a per netns tcp hash table, or
a per netns list of timewait sockets...
Fixes: 0dad4087a86a ("tcp/dccp: get rid of inet_twsk_purge()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Leonard Crestez <cdleonard@gmail.com>
Tested-by: Leonard Crestez <cdleonard@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When suspending the passive scanning _must_ have its filter_policy set
to 0x01 to use the accept list otherwise _any_ advertise report would
end up waking up the system.
In order to fix the filter_policy the code now checks for
hdev->suspended && HCI_CONN_FLAG_REMOTE_WAKEUP
first, since the MGMT_OP_SET_DEVICE_FLAGS will reject any attempt to
set HCI_CONN_FLAG_REMOTE_WAKEUP when it cannot be programmed in the
acceptlist, so it can return success causing the proper filter_policy
to be used.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215768
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
HCI_CONN_FLAG_REMOTE_WAKEUP can only be set if device can be programmed
in the allowlist which in case of device using RPA requires LL Privacy
support to be enabled.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215768
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This driver was using the TX IRQ handler to perform all TX completion
tasks. Under heavy TX network load, this can cause significant irqs-off
latencies (found to be in the hundreds of microseconds using ftrace).
This can cause other issues, such as overrunning serial UART FIFOs when
using high baud rates with limited UART FIFO sizes.
Switch to using a NAPI poll handler to perform the TX completion work
to get this out of hard IRQ context and avoid the IRQ latency impact.
A separate poll handler is used for TX and RX since they have separate
IRQs on this controller, so that the completion work for each of them
stays on the same CPU as the interrupt.
Testing on a Xilinx MPSoC ZU9EG platform using iperf3 from a Linux PC
through a switch at 1G link speed showed no significant change in TX or
RX throughput, with approximately 941 Mbps before and after. Hard IRQ
time in the TX throughput test was significantly reduced from 12% to
below 1% on the CPU handling TX interrupts, with total hard+soft IRQ CPU
usage dropping from about 56% down to 48%.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The axienet_start_xmit function was updating the tx_bd_tail variable
multiple times, with potential rollbacks on error or invalid
intermediate positions, even though this variable is also used in the
TX completion path. Use READ_ONCE where this variable is read and
WRITE_ONCE where it is written to make this update more atomic, and
move the write before the MMIO write to start the transfer, so it is
protected by that implicit write barrier.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sending WMT command during the reset in progress is invalid and would get
no response from firmware until the reset is complete, so we ignore the WMT
command here to resolve the issue which causes the whole reset process
taking too long.
Fixes: 8fafe702253d ("Bluetooth: mt7921s: support bluetooth reset mechanism")
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
According to FW advised sequence, mt7921s need to re-acquire privilege
immediately after the firmware download is complete before normal running.
Otherwise, it is still possible the bus may be stuck in an abnormal status
that causes FW initialization failure in the current driver.
Fixes: 752aea58489f ("Bluetooth: mt7921s: fix bus hang with wrong privilege")
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
INET_MATCH() runs without holding a lock on the socket.
We probably need to annotate most reads.
This patch makes INET_MATCH() an inline function
to ease our changes.
v2:
We remove the 32bit version of it, as modern compilers
should generate the same code really, no need to
try to be smarter.
Also make 'struct net *net' the first argument.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not access skb buffer data anymore after hci_recv_frame was
called.
[ 39.634809] BUG: KASAN: use-after-free in btmtksdio_recv_event+0x1b0
[ 39.634855] Read of size 1 at addr ffffff80cf28a60d by task kworker
[ 39.634962] Call trace:
[ 39.634974] dump_backtrace+0x0/0x3b8
[ 39.634999] show_stack+0x20/0x2c
[ 39.635016] dump_stack_lvl+0x60/0x78
[ 39.635040] print_address_description+0x70/0x2f0
[ 39.635062] kasan_report+0x154/0x194
[ 39.635079] __asan_report_load1_noabort+0x44/0x50
[ 39.635099] btmtksdio_recv_event+0x1b0/0x1c4
[ 39.635129] btmtksdio_txrx_work+0x6cc/0xac4
[ 39.635157] process_one_work+0x560/0xc5c
[ 39.635177] worker_thread+0x7ec/0xcc0
[ 39.635195] kthread+0x2d0/0x3d0
[ 39.635215] ret_from_fork+0x10/0x20
[ 39.635247] Allocated by task 0:
[ 39.635260] (stack is not available)
[ 39.635281] Freed by task 2392:
[ 39.635295] kasan_save_stack+0x38/0x68
[ 39.635319] kasan_set_track+0x28/0x3c
[ 39.635338] kasan_set_free_info+0x28/0x4c
[ 39.635357] ____kasan_slab_free+0x104/0x150
[ 39.635374] __kasan_slab_free+0x18/0x28
[ 39.635391] slab_free_freelist_hook+0x114/0x248
[ 39.635410] kfree+0xf8/0x2b4
[ 39.635427] skb_free_head+0x58/0x98
[ 39.635447] skb_release_data+0x2f4/0x410
[ 39.635464] skb_release_all+0x50/0x60
[ 39.635481] kfree_skb+0xc8/0x25c
[ 39.635498] hci_event_packet+0x894/0xca4 [bluetooth]
[ 39.635721] hci_rx_work+0x1c8/0x68c [bluetooth]
[ 39.635925] process_one_work+0x560/0xc5c
[ 39.635951] worker_thread+0x7ec/0xcc0
[ 39.635970] kthread+0x2d0/0x3d0
[ 39.635990] ret_from_fork+0x10/0x20
[ 39.636021] The buggy address belongs to the object at ffffff80cf28a600
which belongs to the cache kmalloc-512 of size 512
[ 39.636039] The buggy address is located 13 bytes inside of
512-byte region [ffffff80cf28a600, ffffff80cf28a800)
Fixes: 9aebfd4a2200 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices")
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds the device ID for the BCM4373A0 module, found e.g. in
the Infineon (Cypress) CYW4373E chip. The required firmware file is
named 'BCM4373A0.hcd'.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add VID 0489 & PID e0c8 for MediaTek MT7921 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=13 Cnt=03 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e0c8 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Identifies as just "Realtek Semiconductor Corp. Bluetooth Radio"; it's
used in many adapters, e.g.:
- UGREEN CM390
- C-TECH BTD-01
- Orico BTA-508
- KS-is KS-457
Device description at /sys/kernel/debug/usb/devices:
T: Bus=03 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=8771 Rev= 2.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00E04C239987
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Set HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for QCA controllers since
they answer HCI_OP_READ_DEF_ERR_DATA_REPORTING with error code
"UNKNOWN HCI COMMAND" as shown below:
[ 580.517552] Bluetooth: hci0: unexpected cc 0x0c5a length: 1 < 2
[ 580.517660] Bluetooth: hci0: Opcode 0x c5a failed: -38
hcitool -i hci0 cmd 0x03 0x5a
< HCI Command: ogf 0x03, ocf 0x005a, plen 0
> HCI Event: 0x0e plen 4
01 5A 0C 01
btmon log:
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
> HCI Event: Command Complete (0x0e) plen 4
Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Move power_on work cancel to hci_dev_close_sync to ensure that power_on
work is canceled after HCI interface down, power off, rfkill, etc.
For example, if
hciconfig hci0 down
is done early enough during boot, it may run before power_on work.
Then, power_on work will actually bring up interface despite above
hciconfig command.
Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@opensynergy.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Qualcomm WCN785x has PID/VID 0cf3/e700 as shown by
/sys/kernel/debug/usb/devices:
T: Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 8 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=e700 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Concurrent operations from events on le_{accept,resolv}_list are
currently unprotected by hdev->lock.
Most existing code do already protect the lists with that lock.
This can be observed in hci_debugfs and hci_sync.
Add the protection for these events too.
Fixes: b950aa88638c ("Bluetooth: Add definitions and track LE resolve list modification")
Fixes: 0f36b589e4ee ("Bluetooth: Track LE white list modification via HCI commands")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
All accesses (both reads and modifications) to
hdev->{accept,reject}_list are protected by hdev lock,
except the ones in hci_conn_request_evt. This can cause a race
condition in the form of a list corruption.
The solution is to protect these lists in hci_conn_request_evt as well.
I was unable to find the exact commit that introduced the issue for the
reject list, I was only able to find it for the accept list.
Fixes: a55bd29d5227 ("Bluetooth: Add white list lookup for incoming connection requests")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
hci_is_adv_monitoring's function documentation states that it must be
called under the hdev lock. Paths that leads to an unlocked call are:
discov_update => start_discovery => interleaved_discov => active_scan
and: discov_update => start_discovery => active_scan
The solution is to take the lock in active_scan during the duration of
the call to hci_is_adv_monitoring.
Fixes: c32d624640fd ("Bluetooth: disable filter dup when scan for adv monitor")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add the support for RTL8852C BT controller on USB interface.
The necessary firmware file will be submitted to linux-firmware.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This sets HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for QCA controllers
since SCO appear to not work when using HCI_OP_ENHANCED_SETUP_SYNC_CONN.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215576
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This prints warnings for controllers setting broken quirks to increase
their visibility and warn about broken controllers firmware that
probably needs updates to behave properly.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN quirk which can be
used to mark HCI_Enhanced_Setup_Synchronous_Connection as broken even
if its support command bit are set since some controller report it as
supported but the command don't work properly with some configurations
(e.g. BT_VOICE_TRANSPARENT/mSBC).
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
Kalesh AP
Pavan Chebbi
Michael Chan
Enric Balletbo i Serra
Kavyasree Kotagiri
Charan Teja Kalla
Nicholas Piggin
Nícolas F. R. A. Prado
Chuanhong Guo
Fabien Parent
Rui Salvaterra
Dang Huynh
Eric Dumazet
Luiz Augusto von Dentz
Robert Hancock
Sean Wang
Tim Harvey
Ismael Luceno
Zijun Hu
Vasyl Vavrychuk
Niels Dossche
Max Chou