| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The new nvme-apple driver is missing a few conversions to and
from little-endian data:
drivers/nvme/host/apple.c:291:19: sparse: sparse: incorrect type in assignment (different base types) @@ expected unsigned long long [usertype] prp1 @@ got restricted __le64 [usertype] prp1 @@
drivers/nvme/host/apple.c:291:19: sparse: expected unsigned long long [usertype] prp1
drivers/nvme/host/apple.c:291:19: sparse: got restricted __le64 [usertype] prp1
drivers/nvme/host/apple.c:292:19: sparse: sparse: incorrect type in assignment (different base types) @@ expected unsigned long long [usertype] prp2 @@ got restricted __le64 [usertype] prp2 @@
drivers/nvme/host/apple.c:293:21: sparse: sparse: incorrect type in assignment (different base types) @@ expected unsigned int [usertype] length @@ got restricted __le16 [usertype] length @@
drivers/nvme/host/apple.c:351:52: sparse: sparse: incorrect type in initializer (different base types) @@ expected unsigned int [usertype] next_dma_addr @@ got restricted __le64 [usertype] @@
drivers/nvme/host/apple.c:456:45: sparse: sparse: incorrect type in assignment (different base types) @@ expected restricted __le64 [usertype] @@ got unsigned int [addressable] [usertype] prp_dma @@
drivers/nvme/host/apple.c:459:31: sparse: sparse: incorrect type in assignment (different base types) @@ expected restricted __le64 [usertype] @@ got unsigned long long [assigned] [usertype] dma_addr @@
drivers/nvme/host/apple.c:474:25: sparse: sparse: incorrect type in assignment (different base types) @@ expected restricted __le64 [usertype] prp1 @@ got unsigned int [usertype] dma_address @@
drivers/nvme/host/apple.c:475:25: sparse: sparse: incorrect type in assignment (different base types) @@ expected restricted __le64 [usertype] prp2 @@ got unsigned int [usertype] first_dma @@
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Performance states and energy consumption values are not advertised
in ACPI. In the GicC structure of the MADT table, the "Processor
Power Efficiency Class field" (called efficiency class from now)
allows to describe the relative energy efficiency of CPUs.
To leverage the EM and EAS, the CPPC driver creates a set of
artificial performance states and registers them in the Energy Model
(EM), such as:
- Every 20 capacity unit, a performance state is created.
- The energy cost of each performance state gradually increases.
No power value is generated as only the cost is used in the EM.
During task placement, a task can raise the frequency of its whole
pd. This can make EAS place a task on a pd with CPUs that are
individually less energy efficient.
As cost values are artificial, and to place tasks on CPUs with the
lower efficiency class, a gap in cost values is generated for adjacent
efficiency classes.
E.g.:
- efficiency class = 0, capacity is in [0-1024], so cost values
are in [0: 51] (one performance state every 20 capacity unit)
- efficiency class = 1, capacity is in [0-1024], cost values
are in [1*gap+0: 1*gap+51].
The value of the cost gap is chosen to absorb a the energy of 4 CPUs
at their maximum capacity. This means that between:
1- a pd of 4 CPUs, each of them being used at almost their full
capacity. Their efficiency class is N.
2- a CPU using almost none of its capacity. Its efficiency class is
N+1
EAS will choose the first option.
This patch also populates the (struct cpufreq_driver).register_em
callback if the valid efficiency_class ACPI values are provided.
Signed-off-by: Pierre Gondois <Pierre.Gondois@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In ACPI, describing power efficiency of CPUs can be done through the
following arm specific field:
ACPI 6.4, s5.2.12.14 'GIC CPU Interface (GICC) Structure',
'Processor Power Efficiency Class field':
Describes the relative power efficiency of the associated pro-
cessor. Lower efficiency class numbers are more efficient than
higher ones (e.g. efficiency class 0 should be treated as more
efficient than efficiency class 1). However, absolute values
of this number have no meaning: 2 isn’t necessarily half as
efficient as 1.
The efficiency_class field is stored in the GicC structure of the
ACPI MADT table and it's currently supported in Linux for arm64 only.
Thus, this new functionality is introduced for arm64 only.
To allow the cppc_cpufreq driver to know and preprocess the
efficiency_class values of all the CPUs, add a per_cpu efficiency_class
variable to store them.
At least 2 different efficiency classes must be present,
otherwise there is no use in creating an Energy Model.
The efficiency_class values are squeezed in [0:#efficiency_class-1]
while conserving the order. For instance, efficiency classes of:
[111, 212, 250]
will be mapped to:
[0 (was 111), 1 (was 212), 2 (was 250)].
Each policy being independently registered in the driver, populating
the per_cpu efficiency_class is done only once at the driver
initialization. This prevents from having each policy re-searching the
efficiency_class values of other CPUs. The EM will be registered in a
following patch.
The patch also exports acpi_cpu_get_madt_gicc() to fetch the GicC
structure of the ACPI MADT table for each CPU.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Pierre Gondois <Pierre.Gondois@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
For some platforms, the frequency returned by hardware may be slightly
different from what is provided in the frequency table. For example,
hardware may return 499 MHz instead of 500 MHz. In such cases it is
better to avoid getting into unnecessary frequency updates, as we may
end up switching policy->cur between the two and sending unnecessary
pre/post update notifications, etc.
This patch has chosen allows the hardware frequency and table frequency
to deviate by 1 MHz for now, we may want to increase it a bit later on
if someone still complains.
Reported-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Jia-wei Chang <jia-wei.chang@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add high frequency impedance notification support under DPTF.
This returns high frequency impedance value that can be obtained
from battery fuel gauge whenever there is change over a threshold.
Also, corrected the typo from IMPEDANCED_CHNGED to IMPEDANCE_CHANGED.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The documentation of fwnode and device property array API calls isn't
pointing out to the shortcuts to count the number of elements of size
in an array. Amend the documentation to advertise fwnode and device
property count API calls.
Reported-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This will allow super users to verify the module parameters in question
when changed via kernel command line.
The parameters "nocst/bm_check_disable" are only used for enable/disable,
so change them from integer to bool.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Remove various declarations from former s390 specific compat system
calls which have been removed with commit fef747bab3c0 ("s390: use
generic UID16 implementation"). While at it clean up the whole small
header file.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
LLVM's integrated assembler reports the following error when compiling
entry.S:
<instantiation>:38:5: error: unknown token in expression
tm %r8,0x0001 # coming from user space?
The correct instruction would have been tmhh instead of tm.
The current code is doing nothing, since (with gas) it get's
translated to a tm instruction which reads from real address 8, which
again contains always zero, and therefore the conditional code is
never executed.
Note that due to the missing displacement gas translates "%r8" into
"8(%r0)".
Also code inspection reveals that this conditional code is not needed.
Therefore remove it.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Convert parmarea to C, which makes it much easier to initialize it. No need
to keep offsets in assembler code in sync with struct parmarea anymore.
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Convert initial lowcore to C and use proper defines and structures to
initialize it. This should make the z/VM ipl procedure a bit less magic.
Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The short psw definitions are contained in compat header files, however
short psws are not compat specific. Therefore move the definitions to
ptrace header file. This also gets rid of a compat header include in kvm
code.
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Initialize all new psws with disabled wait psws, except for the restart new
psw. This way every unexpected exception, svc, machine check, or interrupt
is handled properly.
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The program check handler of the kernel image points to
startup_pgm_check_handler. However an early program check which happens
while loading the kernel image will jump to potentially random code, since
the code of the program check handler is not yet loaded; leading to a
program check loop.
Therefore initialize it to a disabled wait psw and let the startup code set
the proper psw when everything is in memory.
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Move iplstart entry point to 0x200 again, instead of the middle of the ipl
code. This way even the comment describing the ccw program is correct
again.
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The final kernel image is created by linking decompressor object files with
a startup archive. The startup archive file however does not contain only
optional code and data which can be discarded if not referenced. It also
contains mandatory object data like head.o which must never be discarded,
even if not referenced.
Move the decompresser code and linker script to the boot directory and get
rid of the startup archive so everything is kept during link time.
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
LLVM's integrated assembler does not like comments within macros:
<instantiation>:3:19: error: too many positional arguments
GR_NUM b2, 1 /* Base register */
^
Remove them, since they are obvious anyway.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Use local labels in .set directives to avoid potential compile errors
with LTO + clang. See commit 334865b2915c ("x86/extable: Prefer local
labels in .set directives") for further details.
Since s390 doesn't support LTO currently this doesn't fix a real bug
for now, but helps to avoid problems as soon as required pieces have
been added to llvm.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Use local labels in .set directives to avoid potential compile errors
with LTO + clang. See commit 334865b2915c ("x86/extable: Prefer local
labels in .set directives") for further details.
Since s390 doesn't support LTO currently this doesn't fix a real bug
for now, but helps to avoid problems as soon as required pieces have
been added to llvm.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20220430191122.8667-5-Julia.Lawall@inria.fr
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20220430191122.8667-2-Julia.Lawall@inria.fr
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Currently many console drivers for s390 rely on panic/reboot notifiers
to invoke callbacks on these events. The panic() function disables local
IRQs, secondary CPUs and preemption, so callbacks invoked on panic are
effectively running in atomic context.
Happens that most of these console callbacks from s390 doesn't take the
proper care with regards to atomic context, like taking spinlocks that
might be taken in other function/CPU and hence will cause a lockup
situation.
The goal for this patch is to improve the notifiers reliability, acting
on 4 console drivers, as detailed below:
(1) con3215: changed a regular spinlock to the trylock alternative.
(2) con3270: also changed a regular spinlock to its trylock counterpart,
but here we also have another problem: raw3270_activate_view() takes a
different spinlock. So, we worked a helper to validate if this other lock
is safe to acquire, and if so, raw3270_activate_view() should be safe.
Notice though that there is a functional change here: it's now possible
to continue the notifier code [reaching con3270_wait_write() and
con3270_rebuild_update()] without executing raw3270_activate_view().
(3) sclp: a global lock is used heavily in the functions called from
the notifier, so we added a check here - if the lock is taken already,
we just bail-out, preventing the lockup.
(4) sclp_vt220: same as (3), a lock validation was added to prevent the
potential lockup problem.
Besides (1)-(4), we also removed useless void functions, adding the
code called from the notifier inside its own body, and changed the
priority of such notifiers to execute late, since they are "heavyweight"
for the panic environment, so we aim to reduce risks here.
Changed return values to NOTIFY_DONE as well, the standard one.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Link: https://lore.kernel.org/r/20220427224924.592546-14-gpiccoli@igalia.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Pull kvm fixes from Paolo Bonzini:
"x86:
- Account for family 17h event renumberings in AMD PMU emulation
- Remove CPUID leaf 0xA on AMD processors
- Fix lockdep issue with locking all vCPUs
- Fix loss of A/D bits in SPTEs
- Fix syzkaller issue with invalid guest state"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: Exit to userspace if vCPU has injected exception and invalid state
KVM: SEV: Mark nested locking of vcpu->lock
kvm: x86/cpuid: Only provide CPUID leaf 0xA if host has architectural PMU
KVM: x86/svm: Account for family 17h event renumberings in amd_pmc_perf_hw_id
KVM: x86/mmu: Use atomic XCHG to write TDP MMU SPTEs with volatile bits
KVM: x86/mmu: Move shadow-present check out of spte_has_volatile_bits()
KVM: x86/mmu: Don't treat fully writable SPTEs as volatile (modulo A/D)
|
|
When the battery is neither charging or discharging and is not full,
"not-charging" is a useful status description for the case in general.
Currently this state is set as "unknown" by default, expect when this is
explicitly replaced with "not-charging" on a per device or per vendor
basis.
A lot of devices have this state without a BIOS specification available
explicitly describing it. e.g. some current Clevo barebones have a BIOS
setting to stop charging at a user defined battery level.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When building with W=1, we get the following warning:
drivers/acpi/arm64/agdi.c:88:13: warning: no previous prototype for ‘acpi_agdi_init’ [-Wmissing-prototypes]
void __init acpi_agdi_init(void)
Include AGDI driver's header file to pull in the prototype definition
for acpi_agdi_init() to get rid of the compiler warning
Fixes: a2a591fb76e6 ("ACPI: AGDI: Add driver for Arm Generic Diagnostic Dump and Reset device")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ilkka Koskinen <ilkka@os.amperecomputing.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently the #define IB_SRQ_INIT_MASK is used to distinguish the
rxe_create_srq verb from the rxe_modify_srq verb so that some code can be
shared between these two subroutines.
This commit splits rxe_srq_chk_attr into two subroutines: rxe_srq_chk_init
and rxe_srq_chk_attr which handle the create_srq and modify_srq verbs
separately.
Link: https://lore.kernel.org/r/20220421014042.26985-2-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Pull RISC-V fix from Palmer Dabbelt:
- A fix to relocate the DTB early in boot, in cases where the
bootloader doesn't put the DTB in a region that will end up
mapped by the kernel.
This manifests as a crash early in boot on a handful of
configurations.
* tag 'riscv-for-linus-5.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: relocate DTB if it's outside memory region
|
|
As reported in:
https://lore.kernel.org/linux-perf-users/20220428122821.3652015-1-tmricht@linux.ibm.com/
the 'instructions:u' event may not be supported. Add a skip using 'perf
record'.
Switch some code away from pipe to make the failures clearer.
Reported-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Sumanth Korikkar <sumanthk@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Link: https://lore.kernel.org/r/20220505182505.3313191-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Since the vector length configuration mechanism is identical between SVE
and SME we share large elements of the code including the definition for
the maximum vector length. Unfortunately when we were defining the ABI
for SVE we included not only the actual maximum vector length of 2048
bits but also the value possible if all the bits reserved in the
architecture for expansion of the LEN field were used, 16384 bits.
This starts creating problems if we try to allocate anything for the ZA
matrix based on the maximum possible vector length, as we do for the
regset used with ptrace during the process of generating a core dump.
While the maximum potential size for ZA with the current architecture is
a reasonably managable 64K with the higher reserved limit ZA would be
64M which leads to entirely reasonable complaints from the memory
management code when we try to allocate a buffer of that size. Avoid
these issues by defining the actual maximum vector length for the
architecture and using it for the SME regsets.
Also use the full ZA_PT_SIZE() with the header rather than just the
actual register payload when specifying the size, fixing support for the
largest vector lengths now that we have this new, lower define. With the
SVE maximum this did not cause problems due to the extra headroom we
had.
While we're at it add a comment clarifying why even though ZA is a
single register we tell the regset code that it is a multi-register
regset.
Reported-by: Qian Cai <quic_qiancai@quicinc.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://lore.kernel.org/r/20220505221517.1642014-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
As Yanming reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=215914
The root cause is: in a very small sized image, it's very easy to
exceed threshold of foreground GC, if we calculate free space and
dirty data based on section granularity, in corner case,
has_not_enough_free_secs() will always return true, result in
deadloop in f2fs_gc().
So this patch refactors has_not_enough_free_secs() as below to fix
this issue:
1. calculate needed space based on block granularity, and separate
all blocks to two parts, section part, and block part, comparing
section part to free section, and comparing block part to free space
in openned log.
2. account F2FS_DIRTY_NODES, F2FS_DIRTY_IMETA and F2FS_DIRTY_DENTS
as node block consumer;
3. account F2FS_DIRTY_DENTS as data block consumer;
Cc: stable@vger.kernel.org
Reported-by: Ming Yan <yanming@tju.edu.cn>
Signed-off-by: Chao Yu <chao.yu@oppo.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
As Yanming reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=215894
I have encountered a bug in F2FS file system in kernel v5.17.
I have uploaded the system call sequence as case.c, and a fuzzed image can
be found in google net disk
The kernel should enable CONFIG_KASAN=y and CONFIG_KASAN_INLINE=y. You can
reproduce the bug by running the following commands:
kernel BUG at fs/f2fs/segment.c:2291!
Call Trace:
f2fs_invalidate_blocks+0x193/0x2d0
f2fs_fallocate+0x2593/0x4a70
vfs_fallocate+0x2a5/0xac0
ksys_fallocate+0x35/0x70
__x64_sys_fallocate+0x8e/0xf0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
The root cause is, after image was fuzzed, block mapping info in inode
will be inconsistent with SIT table, so in f2fs_fallocate(), it will cause
panic when updating SIT with invalid blkaddr.
Let's fix the issue by adding sanity check on block address before updating
SIT table with it.
Cc: stable@vger.kernel.org
Reported-by: Ming Yan <yanming@tju.edu.cn>
Signed-off-by: Chao Yu <chao.yu@oppo.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
As Yanming reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=215897
I have encountered a bug in F2FS file system in kernel v5.17.
The kernel should enable CONFIG_KASAN=y and CONFIG_KASAN_INLINE=y. You can
reproduce the bug by running the following commands:
The kernel message is shown below:
kernel BUG at fs/f2fs/f2fs.h:2511!
Call Trace:
f2fs_remove_inode_page+0x2a2/0x830
f2fs_evict_inode+0x9b7/0x1510
evict+0x282/0x4e0
do_unlinkat+0x33a/0x540
__x64_sys_unlinkat+0x8e/0xd0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
The root cause is: .total_valid_block_count or .total_valid_node_count
could fuzzed to zero, then once dec_valid_node_count() was called, it
will cause BUG_ON(), this patch fixes to print warning info and set
SBI_NEED_FSCK into CP instead of panic.
Cc: stable@vger.kernel.org
Reported-by: Ming Yan <yanming@tju.edu.cn>
Signed-off-by: Chao Yu <chao.yu@oppo.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
If there's not enough free sections each of which consistis of large segments,
we can hit no free section for upcoming section allocation. Let's reclaim some
prefree segments by writing checkpoints.
Signed-off-by: Byungki Lee <dominicus79@gmail.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
As Yanming reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=215904
The kernel message is shown below:
kernel BUG at fs/f2fs/inode.c:825!
Call Trace:
evict+0x282/0x4e0
__dentry_kill+0x2b2/0x4d0
shrink_dentry_list+0x17c/0x4f0
shrink_dcache_parent+0x143/0x1e0
do_one_tree+0x9/0x30
shrink_dcache_for_umount+0x51/0x120
generic_shutdown_super+0x5c/0x3a0
kill_block_super+0x90/0xd0
kill_f2fs_super+0x225/0x310
deactivate_locked_super+0x78/0xc0
cleanup_mnt+0x2b7/0x480
task_work_run+0xc8/0x150
exit_to_user_mode_prepare+0x14a/0x150
syscall_exit_to_user_mode+0x1d/0x40
do_syscall_64+0x48/0x90
The root cause is: inode node and dnode node share the same nid,
so during f2fs_evict_inode(), dnode node truncation will invalidate
its NAT entry, so when truncating inode node, it fails due to
invalid NAT entry, result in inode is still marked as dirty, fix
this issue by clearing dirty for inode and setting SBI_NEED_FSCK
flag in filesystem.
output from dump.f2fs:
[print_node_info: 354] Node ID [0xf:15] is inode
i_nid[0] [0x f : 15]
Cc: stable@vger.kernel.org
Reported-by: Ming Yan <yanming@tju.edu.cn>
Signed-off-by: Chao Yu <chao.yu@oppo.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
F2FS zoned support has power of 2 zone size assumption in many places
such as in __f2fs_issue_discard_zone, init_blkz_info. As the power of 2
requirement has been removed from the block layer, explicitly add a
condition in f2fs to allow only power of 2 zone size devices.
This condition will be relaxed once those calculation based on power of
2 is made generic.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
Instead of calling bdev_zone_sectors() multiple times, call
it once and cache the value locally. This will make the
subsequent change easier to read.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
There are multiple calculations and reads of fields of sbi that should
be protected by stat_lock. As stat_lock is not used to read these
values in statfs, this can lead to inconsistent results.
Extend the locking to prevent this issue.
Commit c9c8ed50d94c ("f2fs: fix to avoid potential race on
sbi->unusable_block_count access/update")
already added the use of sbi->stat_lock in statfs in
order to make the calculation of multiple, different fields atomic so
that results are consistent. This is similar to that patch regarding the
change in statfs.
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
xfstests/generic/475 can give EIO all the time which give an infinite loop
to flush node page like below. Let's avoid it.
[16418.518551] Call Trace:
[16418.518553] ? dm_submit_bio+0x48/0x400
[16418.518574] ? submit_bio_checks+0x1ac/0x5a0
[16418.525207] __submit_bio+0x1a9/0x230
[16418.525210] ? kmem_cache_alloc+0x29e/0x3c0
[16418.525223] submit_bio_noacct+0xa8/0x2b0
[16418.525226] submit_bio+0x4d/0x130
[16418.525238] __submit_bio+0x49/0x310 [f2fs]
[16418.525339] ? bio_add_page+0x6a/0x90
[16418.525344] f2fs_submit_page_bio+0x134/0x1f0 [f2fs]
[16418.525365] read_node_page+0x125/0x1b0 [f2fs]
[16418.525388] __get_node_page.part.0+0x58/0x3f0 [f2fs]
[16418.525409] __get_node_page+0x2f/0x60 [f2fs]
[16418.525431] f2fs_get_dnode_of_data+0x423/0x860 [f2fs]
[16418.525452] ? asm_sysvec_apic_timer_interrupt+0x12/0x20
[16418.525458] ? __mod_memcg_state.part.0+0x2a/0x30
[16418.525465] ? __mod_memcg_lruvec_state+0x27/0x40
[16418.525467] ? __xa_set_mark+0x57/0x70
[16418.525472] f2fs_do_write_data_page+0x10e/0x7b0 [f2fs]
[16418.525493] f2fs_write_single_data_page+0x555/0x830 [f2fs]
[16418.525514] ? sysvec_apic_timer_interrupt+0x4e/0x90
[16418.525518] ? asm_sysvec_apic_timer_interrupt+0x12/0x20
[16418.525523] f2fs_write_cache_pages+0x303/0x880 [f2fs]
[16418.525545] ? blk_flush_plug_list+0x47/0x100
[16418.525548] f2fs_write_data_pages+0xfd/0x320 [f2fs]
[16418.525569] do_writepages+0xd5/0x210
[16418.525648] filemap_fdatawrite_wbc+0x7d/0xc0
[16418.525655] filemap_fdatawrite+0x50/0x70
[16418.525658] f2fs_sync_dirty_inodes+0xa4/0x230 [f2fs]
[16418.525679] f2fs_write_checkpoint+0x16d/0x1720 [f2fs]
[16418.525699] ? ttwu_do_wakeup+0x1c/0x160
[16418.525709] ? ttwu_do_activate+0x6d/0xd0
[16418.525711] ? __wait_for_common+0x11d/0x150
[16418.525715] kill_f2fs_super+0xca/0x100 [f2fs]
[16418.525733] deactivate_locked_super+0x3b/0xb0
[16418.525739] deactivate_super+0x40/0x50
[16418.525741] cleanup_mnt+0x139/0x190
[16418.525747] __cleanup_mnt+0x12/0x20
[16418.525749] task_work_run+0x6d/0xa0
[16418.525765] exit_to_user_mode_prepare+0x1ad/0x1b0
[16418.525771] syscall_exit_to_user_mode+0x27/0x50
[16418.525774] do_syscall_64+0x48/0xc0
[16418.525776] entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
The block layer for zoned disk can reorder the FUA'ed IOs. Let's use flush
command to keep the write order.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
Syzbot triggers two WARNs in f2fs_is_valid_blkaddr and
__is_bitmap_valid. For example, in f2fs_is_valid_blkaddr,
if type is DATA_GENERIC_ENHANCE or DATA_GENERIC_ENHANCE_READ,
it invokes WARN_ON if blkaddr is not in the right range.
The call trace is as follows:
f2fs_get_node_info+0x45f/0x1070
read_node_page+0x577/0x1190
__get_node_page.part.0+0x9e/0x10e0
__get_node_page
f2fs_get_node_page+0x109/0x180
do_read_inode
f2fs_iget+0x2a5/0x58b0
f2fs_fill_super+0x3b39/0x7ca0
Fix these two WARNs by replacing WARN_ON with dump_stack.
Reported-by: syzbot+763ae12a2ede1d99d4dc@syzkaller.appspotmail.com
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
Read stale PTP Tx timestamps from PHY on cleanup.
After running out of Tx timestamps request handlers, hardware (HW) stops
reporting finished requests. Function ice_ptp_tx_tstamp_cleanup() used
to only clean up stale handlers in driver and was leaving the hardware
registers not read. Not reading stale PTP Tx timestamps prevents next
interrupts from arriving and makes timestamping unusable.
Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The iAVF driver uses 3 virtchnl op codes to communicate with the PF
regarding the VF Tx queues:
* VIRTCHNL_OP_CONFIG_VSI_QUEUES configures the hardware and firmware
logic for the Tx queues
* VIRTCHNL_OP_ENABLE_QUEUES configures the queue interrupts
* VIRTCHNL_OP_DISABLE_QUEUES disables the queue interrupts and Tx rings.
There is a bug in the iAVF driver due to the race condition between VF
reset request and shutdown being executed in parallel. This leads to a
break in logic and VIRTCHNL_OP_DISABLE_QUEUES is not being sent.
If this occurs, the PF driver never cleans up the Tx queues. This results
in leaving behind stale Tx queue settings in the hardware and firmware.
The most obvious outcome is that upon the next
VIRTCHNL_OP_CONFIG_VSI_QUEUES, the PF will fail to program the Tx
scheduler node due to a lack of space.
We need to protect ICE driver against such situation.
To fix this, make sure we clear existing stale settings out when
handling VIRTCHNL_OP_CONFIG_VSI_QUEUES. This ensures we remove the
previous settings.
Calling ice_vf_vsi_dis_single_txq should be safe as it will do nothing if
the queue is not configured. The function already handles the case when the
Tx queue is not currently configured and exits with a 0 return in that
case.
Fixes: 7ad15440acf8 ("ice: Refactor VIRTCHNL_OP_CONFIG_VSI_QUEUES handling")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Function ice_plug_aux_dev() assigns pf->adev field too early prior
aux device initialization and on other side ice_unplug_aux_dev()
starts aux device deinit and at the end assigns NULL to pf->adev.
This is wrong because pf->adev should always be non-NULL only when
aux device is fully initialized and ready. This wrong order causes
a crash when ice_send_event_to_aux() call occurs because that function
depends on non-NULL value of pf->adev and does not assume that
aux device is half-initialized or half-destroyed.
After order correction the race window is tiny but it is still there,
as Leon mentioned and manipulation with pf->adev needs to be protected
by mutex.
Fix (un-)plugging functions so pf->adev field is set after aux device
init and prior aux device destroy and protect pf->adev assignment by
new mutex. This mutex is also held during ice_send_event_to_aux()
call to ensure that aux device is valid during that call.
Note that device lock used ice_send_event_to_aux() needs to be kept
to avoid race with aux drv unload.
Reproducer:
cycle=1
while :;do
echo "#### Cycle: $cycle"
ip link set ens7f0 mtu 9000
ip link add bond0 type bond mode 1 miimon 100
ip link set bond0 up
ifenslave bond0 ens7f0
ip link set bond0 mtu 9000
ethtool -L ens7f0 combined 1
ip link del bond0
ip link set ens7f0 mtu 1500
sleep 1
let cycle++
done
In short when the device is added/removed to/from bond the aux device
is unplugged/plugged. When MTU of the device is changed an event is
sent to aux device asynchronously. This can race with (un)plugging
operation and because pf->adev is set too early (plug) or too late
(unplug) the function ice_send_event_to_aux() can touch uninitialized
or destroyed fields. In the case of crash below pf->adev->dev.mutex.
Crash:
[ 53.372066] bond0: (slave ens7f0): making interface the new active one
[ 53.378622] bond0: (slave ens7f0): Enslaving as an active interface with an u
p link
[ 53.386294] IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
[ 53.549104] bond0: (slave ens7f1): Enslaving as a backup interface with an up
link
[ 54.118906] ice 0000:ca:00.0 ens7f0: Number of in use tx queues changed inval
idating tc mappings. Priority traffic classification disabled!
[ 54.233374] ice 0000:ca:00.1 ens7f1: Number of in use tx queues changed inval
idating tc mappings. Priority traffic classification disabled!
[ 54.248204] bond0: (slave ens7f0): Releasing backup interface
[ 54.253955] bond0: (slave ens7f1): making interface the new active one
[ 54.274875] bond0: (slave ens7f1): Releasing backup interface
[ 54.289153] bond0 (unregistering): Released all slaves
[ 55.383179] MII link monitoring set to 100 ms
[ 55.398696] bond0: (slave ens7f0): making interface the new active one
[ 55.405241] BUG: kernel NULL pointer dereference, address: 0000000000000080
[ 55.405289] bond0: (slave ens7f0): Enslaving as an active interface with an u
p link
[ 55.412198] #PF: supervisor write access in kernel mode
[ 55.412200] #PF: error_code(0x0002) - not-present page
[ 55.412201] PGD 25d2ad067 P4D 0
[ 55.412204] Oops: 0002 [#1] PREEMPT SMP NOPTI
[ 55.412207] CPU: 0 PID: 403 Comm: kworker/0:2 Kdump: loaded Tainted: G S
5.17.0-13579-g57f2d6540f03 #1
[ 55.429094] bond0: (slave ens7f1): Enslaving as a backup interface with an up
link
[ 55.430224] Hardware name: Dell Inc. PowerEdge R750/06V45N, BIOS 1.4.4 10/07/
2021
[ 55.430226] Workqueue: ice ice_service_task [ice]
[ 55.468169] RIP: 0010:mutex_unlock+0x10/0x20
[ 55.472439] Code: 0f b1 13 74 96 eb e0 4c 89 ee eb d8 e8 79 54 ff ff 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 65 48 8b 04 25 40 ef 01 00 31 d2 <f0> 48 0f b1 17 75 01 c3 e9 e3 fe ff ff 0f 1f 00 0f 1f 44 00 00 48
[ 55.491186] RSP: 0018:ff4454230d7d7e28 EFLAGS: 00010246
[ 55.496413] RAX: ff1a79b208b08000 RBX: ff1a79b2182e8880 RCX: 0000000000000001
[ 55.503545] RDX: 0000000000000000 RSI: ff4454230d7d7db0 RDI: 0000000000000080
[ 55.510678] RBP: ff1a79d1c7e48b68 R08: ff4454230d7d7db0 R09: 0000000000000041
[ 55.517812] R10: 00000000000000a5 R11: 00000000000006e6 R12: ff1a79d1c7e48bc0
[ 55.524945] R13: 0000000000000000 R14: ff1a79d0ffc305c0 R15: 0000000000000000
[ 55.532076] FS: 0000000000000000(0000) GS:ff1a79d0ffc00000(0000) knlGS:0000000000000000
[ 55.540163] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 55.545908] CR2: 0000000000000080 CR3: 00000003487ae003 CR4: 0000000000771ef0
[ 55.553041] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 55.560173] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 55.567305] PKRU: 55555554
[ 55.570018] Call Trace:
[ 55.572474] <TASK>
[ 55.574579] ice_service_task+0xaab/0xef0 [ice]
[ 55.579130] process_one_work+0x1c5/0x390
[ 55.583141] ? process_one_work+0x390/0x390
[ 55.587326] worker_thread+0x30/0x360
[ 55.590994] ? process_one_work+0x390/0x390
[ 55.595180] kthread+0xe6/0x110
[ 55.598325] ? kthread_complete_and_exit+0x20/0x20
[ 55.603116] ret_from_fork+0x1f/0x30
[ 55.606698] </TASK>
Fixes: f9f5301e7e2d ("ice: Register auxiliary device to provide RDMA")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Exit to userspace with an emulation error if KVM encounters an injected
exception with invalid guest state, in addition to the existing check of
bailing if there's a pending exception (KVM doesn't support emulating
exceptions except when emulating real mode via vm86).
In theory, KVM should never get to such a situation as KVM is supposed to
exit to userspace before injecting an exception with invalid guest state.
But in practice, userspace can intervene and manually inject an exception
and/or stuff registers to force invalid guest state while a previously
injected exception is awaiting reinjection.
Fixes: fc4fad79fc3d ("KVM: VMX: Reject KVM_RUN if emulation is required with pending exception")
Reported-by: syzbot+cfafed3bb76d3e37581b@syzkaller.appspotmail.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220502221850.131873-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
svm_vm_migrate_from() uses sev_lock_vcpus_for_migration() to lock all
source and target vcpu->locks. Unfortunately there is an 8 subclass
limit, so a new subclass cannot be used for each vCPU. Instead maintain
ownership of the first vcpu's mutex.dep_map using a role specific
subclass: source vs target. Release the other vcpu's mutex.dep_maps.
Fixes: b56639318bb2b ("KVM: SEV: Add support for SEV intra host migration")
Reported-by: John Sperbeck<jsperbeck@google.com>
Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Sean Christopherson <seanjc@google.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Hillf Danton <hdanton@sina.com>
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Peter Gonda <pgonda@google.com>
Message-Id: <20220502165807.529624-1-pgonda@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This reverts commit bfaaba99e680bf82bf2cbf69866c3f37434ff766.
Commit bfaaba99e680 ("ice: Hide bus-info in ethtool for PRs in switchdev
mode") was a workaround for lshw tool displaying incorrect
descriptions for port representors and PF in switchdev mode. Now the issue
has been fixed in the lshw tool itself [1].
Removing the workaround can be considered a regression, as the user might
be running older, unpatched lshw version. However, another important change
(ice: link representors to PCI device, which improves port representor
netdev naming with SET_NETDEV_DEV) also causes the same "regression" as
removing the workaround, i.e. unpatched lshw is able to access bus-info
information (this time not via ethtool) and the bug can occur. Therefore,
the workaround no longer prevents the bug and can be removed.
[1] https://ezix.org/src/pkg/lshw/commit/9bf4e4c9c1
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Pull rdma fixes from Jason Gunthorpe:
"A few recent regressions in rxe's multicast code, and some old driver
bugs:
- Error case unwind bug in rxe for rkeys
- Dot not call netdev functions under a spinlock in rxe multicast
code
- Use the proper BH lock type in rxe multicast code
- Fix idrma deadlock and crash
- Add a missing flush to drain irdma QPs when in error
- Fix high userspace latency in irdma during destroy due to
synchronize_rcu()
- Rare race in siw MPA processing"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/rxe: Change mcg_lock to a _bh lock
RDMA/rxe: Do not call dev_mc_add/del() under a spinlock
RDMA/siw: Fix a condition race issue in MPA request processing
RDMA/irdma: Fix possible crash due to NULL netdev in notifier
RDMA/irdma: Reduce iWARP QP destroy time
RDMA/irdma: Flush iWARP QP if modified to ERR from RTR state
RDMA/rxe: Recheck the MR in when generating a READ reply
RDMA/irdma: Fix deadlock in irdma_cleanup_cm_core()
RDMA/rxe: Fix "Replace mr by rkey in responder resources"
|
|
Pull mmc fixes from Ulf Hansson:
"MMC core:
- Fix initialization for eMMC's HS200/HS400 mode
MMC host:
- sdhci-msm: Reset GCC_SDCC_BCR register to prevent timeout issues
- sunxi-mmc: Fix DMA descriptors allocated above 32 bits"
* tag 'mmc-v5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-msm: Reset GCC_SDCC_BCR register for SDHC
mmc: sunxi-mmc: Fix DMA descriptors allocated above 32 bits
mmc: core: Set HS clock speed before sending HS CMD13
|
|
Link port representors to parent PCI device to benefit from
systemd defined naming scheme.
Example from ip tool:
- without linking:
eth0 ...
- with linking:
eth0 ...
altname enp24s0f0npf0vf0
The port representor name is being shown in altname, because the name is
longer than IFNAMSIZ (16) limit. Altname can be used in ip tool.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
Arnd Bergmann
Pierre Gondois
Rafael J. Wysocki
Viresh Kumar
Sumeet Pawnikar
Andy Shevchenko
Yajun Deng
Heiko Carstens
Julia Lawall
Guilherme G. Piccoli
Linus Torvalds
Werner Sembach
Ilkka Koskinen
Bob Pearson
Ian Rogers
Mark Brown
Chao Yu
Byungki Lee
Luis Chamberlain
Niels Dossche
Jaegeuk Kim
Dongliang Mu
Michal Michalik
Anatolii Gerasymenko
Ivan Vecera
Sean Christopherson
Peter Gonda
Marcin Szycik
Michal Swiatkowski