| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Fix the 'make dtbs_check' warning:
arch/arm64/boot/dts/qcom/sc7280-idp.dt.yaml: phy@1c0e000:
'lanes@1c0e200' does not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+'
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220228123019.382037-5-bhupesh.sharma@linaro.org
|
|
The following properties are not supported and causing dtbs_check
warnings.
- vdda-phy-max-microamp
- vdda-pll-max-microamp
- vddp-ref-clk-max-microamp
- vddp-ref-clk-always-on
arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dt.yaml: phy@627000:
'vdda-phy-max-microamp', 'vddp-ref-clk-always-on', 'vddp-ref-clk-max-microamp'
do not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+'
Drop them from QMP PHY nodes for 'msm8996-xiaomi' dts.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220228123019.382037-4-bhupesh.sharma@linaro.org
|
|
The BAM Data Multiplexer provides access to the network data channels
of modems integrated into many older Qualcomm SoCs, including MSM8916.
Add the nodes for the BAM DMA engine and BAM-DMUX to enable using WWAN
on smartphones/tablets based on MSM8916. This should work out of the box
with open-source WWAN userspace such as ModemManager.
The nodes are disabled by default to avoid loading unnecessary drivers
on devices that cannot use BAM-DMUX (e.g. DragonBoard 410c). However,
strictly speaking the nodes could be enabled by default since both the
bam_dma and bam_dmux driver will simply do nothing if the modem does
not announce any BAM-DMUX channels.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220228225400.146555-3-stephan@gerhold.net
|
|
Add PM8450 PMIC device tree include file. It is going to be used by
SM8450-based devices.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220226205035.1826360-8-dmitry.baryshkov@linaro.org
|
|
Most of SoC device trees do not provide the thermal_zones label. Thus
stop depending on it and use the full path to the thermal zones nodes.
Fixes: 7a3544e5d4e8 ("arm64: dts: qcom: pmr735a: Add temp-alarm support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220226205035.1826360-6-dmitry.baryshkov@linaro.org
|
|
Most of SoC device trees do not provide the thermal_zones label. Thus
stop depending on it and use the full path to the thermal zones nodes.
Fixes: 3795fe7d497b ("arm64: dts: qcom: pm8350c: Add temp-alarm support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220226205035.1826360-5-dmitry.baryshkov@linaro.org
|
|
Add temp-alarm device tree node and a default configuration for the
corresponding thermal zone for this PMIC. Temperatures are based on
downstream values.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220226205035.1826360-4-dmitry.baryshkov@linaro.org
|
|
Add temp-alarm device tree node and a default configuration for the
corresponding thermal zone for this PMIC. Temperatures are based on
downstream values.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220226205035.1826360-3-dmitry.baryshkov@linaro.org
|
|
Add temp-alarm device tree node and a default configuration for the
corresponding thermal zone for this PMIC. Temperatures are based on
downstream values.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220226205035.1826360-2-dmitry.baryshkov@linaro.org
|
|
The IPQ60xx has the same MDIO bug block as IPQ4019. Add IO range and
clock resources description.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/ef01a79ccc6ef86dc3a10d0fa3331794d49e9859.1646031524.git.baruch@tkos.co.il
|
|
The OnePlus 5/5T both have an NXP PN553 which is supported by the
nxp-nci-i2c driver in mainline. It detects/reads NFC tags using
"nfctool" and with the NearD test scripts data can also be written
to be received by another device.
Signed-off-by: Jami Kettunen <jami.kettunen@somainline.org>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220225215642.3916-1-jami.kettunen@somainline.org
|
|
Rename the edp_out label in the sc7280 platform to mdss_edp_out
so that the nodes related to mdss are all grouped together in
the board specific files.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1647452154-16361-2-git-send-email-quic_sbillaka@quicinc.com
|
|
Enable the ethernet node, add the phy node and pinctrl for ethernet.
[bhsharma: Correct ethernet/rgmii related pinmuxs, specify multi-queues and
plug in the PHY interrupt for WOL]
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220325163537.1579969-3-bhupesh.sharma@linaro.org
|
|
SM8150 SoC supports ethqos ethernet controller so add the node for it
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
[bhsharma: Correct ethernet interrupt numbers and add power-domain]
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220325163537.1579969-2-bhupesh.sharma@linaro.org
|
|
Configure and enable the nodes for UFS that are used for internal
storage on FP4.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220321133318.99406-7-luca.weiss@fairphone.com
|
|
Add the necessary nodes for UFS and its PHY.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220321133318.99406-6-luca.weiss@fairphone.com
|
|
Following sm8150/sm8250 update sdm845 capacity-dmips-mhz and
dynamic-power-coefficient based on the measurements [1], [2].
The energy model dynamic-power-coefficient values were calculated with
DPC = µW / MHz / V^2
for each OPP, and averaged across all OPPs within each cluster for the
final coefficient. Voltages were obtained from the qcom-cpufreq-hw
driver that reads voltages from the OSM LUT programmed into the SoC.
Normalized DMIPS/MHz capacity scale values for each CPU were calculated
from CoreMarks/MHz (CoreMark iterations per second per MHz), which
serves the same purpose. For each CPU, the final capacity-dmips-mhz
value is the C/MHz value of its maximum frequency normalized to
SCHED_CAPACITY_SCALE (1024) for the fastest CPU in the system.
For more details on measurement process see the commit message for the
commit 6aabed5526ee ("arm64: dts: qcom: sm8250: Add CPU capacities and
energy model").
[1] https://github.com/kdrag0n/freqbench
[2] https://github.com/kdrag0n/freqbench/tree/master/results/sdm845/main
Cc: Danny Lin <danny@kdrag0n.dev>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220315141104.730235-1-dmitry.baryshkov@linaro.org
|
|
Several wakeup gpios supported by the Top Level Mode Multiplexer (TLMM)
block on sm8150 can be used as interrupt sources and these interrupts
are routed to the PDC interrupt controller.
So, specify PDC as the interrupt parent for the TLMM block.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220226184028.111566-5-bhupesh.sharma@linaro.org
|
|
Add fastrpc device tree nodes for aDSP, cDSP and SLPI.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220410205901.1672089-3-dmitry.baryshkov@linaro.org
|
|
Enable the audio, compute, sensor and modem remoteproc and specify
firmware path for these on the Qualcomm SM8450 HDK.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220410205901.1672089-2-dmitry.baryshkov@linaro.org
|
|
On MSM8996 PCI controller bindings are not compatible with snps,dw-pcie
binding. The platform doesn't provide second (global) IRQ, it requires
additional glue code. To prevent it from probing against the dw-pcie
driver, remove corresponding compatible.
Fixes: ed965ef89227 ("arm64: dts: qcom: msm8996: add support to pcie")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220411115808.1976500-2-dmitry.baryshkov@linaro.org
|
|
On SDM845 PCI controller bindings are not compatible with snps,dw-pcie
binding. The platform doesn't provide second (global) IRQ, it requires
additional glue code. To prevent it from probing against the dw-pcie
driver, remove corresponding compatible.
Fixes: 5c538e09cb19 ("arm64: dts: qcom: sdm845: Add first PCIe controller and PHY")
Fixes: 42ad231338c1 ("arm64: dts: qcom: sdm845: Add second PCIe PHY and controller")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220411115808.1976500-1-dmitry.baryshkov@linaro.org
|
|
APQ8096 provides a 'modem' with reduced functionality, mainly targeting
location services. Enable corresponding device tree node.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220403193911.1393920-3-dmitry.baryshkov@linaro.org
|
|
Enable mss_pil and slpi_pil and set their firmware paths.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #db820c
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210926190555.278589-6-y.oudjana@protonmail.com
|
|
Add nodes for the MSS and SLPI remoteprocs.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #db820c
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210926190555.278589-5-y.oudjana@protonmail.com
|
|
Rename smp2p-modem to smp2p-mpss, and make the subnode labels of smp2p_adsp
and smp2p_slpi follow the <name>_smp2p_<out/in> layout.
Also move smp2p_slpi_out above smp2p_slpi_in to make it match mpss and adsp
where master-kernel is the first subnode.
This patch brings no functional change.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #db820c
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210926190555.278589-4-y.oudjana@protonmail.com
|
|
Fix a total overlap between zap_shader_region and slpi_region, and rename
all regions to match the naming convention in other Qualcomm SoC device trees.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #db820c
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210926190555.278589-2-y.oudjana@protonmail.com
|
|
Add support for uSD card on SA8155p-ADP board using the SDHC2
interface.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220403144151.92572-3-bhupesh.sharma@linaro.org
|
|
Add support for SDC2 which can be used to interface uSD card.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220403144151.92572-2-bhupesh.sharma@linaro.org
|
|
Dragonboard845c doesn't have board-specific board-id programmed, it uses
generic 0xff. Thus add the property with the 'variant' of the
calibration data.
Note: the driver will check for the calibration data for the following
IDs, so older board-2.bin files that were distributed as a part of
Linaro releases will continue to work.
- 'bus=snoc,qmi-board-id=ff,qmi-chip-id=30214,variant=Thundercomm_DB845C'
- 'bus=snoc,qmi-board-id=ff,qmi-chip-id=30214'
- 'bus=snoc,qmi-board-id=ff'
For the reference, the board is identified by the driver in the
following way:
ath10k_snoc 18800000.wifi: qmi chip_id 0x30214 chip_family 0x4001 board_id 0xff soc_id 0x40030001
ath10k_snoc 18800000.wifi: qmi fw_version 0x2009856b fw_build_timestamp 2018-07-19 12:28 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
Fixes: 3f72e2d3e682 ("arm64: dts: qcom: Add Dragonboard 845c")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220403105711.1173161-1-dmitry.baryshkov@linaro.org
|
|
The DT schema expects clocks core-iface order. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220405063451.12011-3-krzysztof.kozlowski@linaro.org
|
|
The DT schema expects dma channels in tx-rx order. No functional
change.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220405063451.12011-2-krzysztof.kozlowski@linaro.org
|
|
The "bluetooth" is more popular and more descriptive than "bt", for a
Bluetooth device. The WCNSS DT schema will expect such naming.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220405065752.27389-2-krzysztof.kozlowski@linaro.org
|
|
Set the default dr_mode for usb2 node to "otg" to enable
role-switch for EUD(Embedded USB Debugger) connector node.
Signed-off-by: Souradeep Chowdhury <quic_schowdhu@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/451392a942f90aa9805b00afad7dff894604d189.1649235218.git.quic_schowdhu@quicinc.com
|
|
Add DTS node for WCN6750 WiFi chipset.
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220406111303.27670-1-quic_mpubbise@quicinc.com
|
|
ref_clk clock in UFS node is already there with a <0 0> frequency, which
matches other DTSI files.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220407092725.232463-3-krzysztof.kozlowski@linaro.org
|
|
The Qualcomm UFS bindings require to use specific (qcom,msm8996-ufshc)
and generic (jedec,ufs-2.0) compatibles.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220407092725.232463-2-krzysztof.kozlowski@linaro.org
|
|
The property vddp-ref-clk-max-microamp (for VDDP ref clk supply which is
l25 regulator) is not documented in MSM8996 UFS PHY bindings
(qcom,msm8996-qmp-ufs-phy). It is mentioned in the other UFS PHY
bindings for qcom,msm8996-ufs-phy-qmp-14nm.
The MSM8996-based Xiaomi devices configure l25 regulator in a
conflicting way:
1. with maximum 100 uAmp for VDDP ref clk supply of UFS PHY,
2. with maximum 450 mAmp for VCCQ supply of UFS.
Since the vddp-ref-clk-max-microamp property is basically not
documented for that UFS PHY and has a conflicting values, drop it
entirely as it looks like not tested and not used ever.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220407092725.232463-1-krzysztof.kozlowski@linaro.org
|
|
The node names should be generic and SPI NOR dtschema expects "flash".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220407143112.294930-2-krzysztof.kozlowski@linaro.org
|
|
Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.
It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
[bjorn: Updated subject prefix]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220407225254.2178644-1-robh@kernel.org
|
|
The referenced commit generates a reference counting error if the rkey has
the same index but the wrong key. In this case the reference taken by
rxe_pool_get_index() is not dropped.
Drop the reference if the keys don't match in rxe_recheck_mr(). Check
that the mw and mr are still valid.
Fixes: 8a1a0be894da ("RDMA/rxe: Replace mr by rkey in responder resources")
Link: https://lore.kernel.org/r/20220411030647.20011-1-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Current rxe_requester() doesn't generate a completion when processing an
unsupported/invalid opcode. If rxe driver doesn't support a new opcode
(e.g. RDMA Atomic Write) and RDMA library supports it, an application
using the new opcode can reproduce this issue. Fix the issue by calling
"goto err;".
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20220410113513.27537-1-yangx.jy@fujitsu.com
Signed-off-by: Xiao Yang <yangx.jy@fujitsu.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
There are some spelling mistakes in the comments. Fix it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220411032458.2517551-1-lv.ruyi@zte.com.cn
|
|
There are some spelling mistakes in the comments. Fix it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408095803.2495336-1-lv.ruyi@zte.com.cn
|
|
Tasklets have long been deprecated as being too heavy on the system
by running in irq context - and this is not a performance critical
path. If a higher priority process wants to run, it must wait for
the tasklet to finish before doing so.
rtllib_sta_ps() and ieee80211_sta_ps() will now run in process context
and have further concurrency (tasklets being serialized among themselves),
but this is done holding the ieee->lock, so it should be fine.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Link: https://lore.kernel.org/r/20220411151620.129178-7-dave@stgolabs.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is unused.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Link: https://lore.kernel.org/r/20220411151620.129178-6-dave@stgolabs.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Tasklets have long been deprecated as being too heavy on the system
by running in irq context - and this is not a performance critical
path. If a higher priority process wants to run, it must wait for
the tasklet to finish before doing so.
The execution of the SME event will now occur in task context. There
are, however, changes in concurrency. Workqueues, unlike tasklets,
are not serialized among themselves and can run concurrently
updating sme_i.qhead. However, the current code is already exposed
in same ways, regardless of the deferral mechanism, in that
hostif_sme_enqueue() does unserialized enqueues updating sme_i.qtail.
Also get rid of the bogus (power save) tasklet enabling, as it
is never disabled to begin with.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Link: https://lore.kernel.org/r/20220411151620.129178-5-dave@stgolabs.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Tasklets have long been deprecated as being too heavy on the system
by running in irq context - and this is not a performance critical
path. If a higher priority process wants to run, it must wait for
the tasklet to finish before doing so.
The completion_bh tasklet will now run in process context and have
further concurrency (tasklets being serialized among themselves),
but this is done holding the ctlxq.lock, so it should be fine.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Link: https://lore.kernel.org/r/20220411151620.129178-4-dave@stgolabs.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Tasklets have long been deprecated as being too heavy on the system
by running in irq context - and this is not a performance critical
path. If a higher priority process wants to run, it must wait for
the tasklet to finish before doing so.
The reaper_bh tasklet will now run in process context and have further
concurrency (tasklets being serialized among themselves), but this
is done holding the ctlxq.lock, so it should be fine.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Link: https://lore.kernel.org/r/20220411151620.129178-3-dave@stgolabs.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Tasklets have long been deprecated as being too heavy on the system
by running in irq context - and this is not a performance critical
path. If a higher priority process wants to run, it must wait for
the tasklet to finish before doing so. A more suitable equivalent
is to converted to threaded irq instead and service channels in
regular task context.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Link: https://lore.kernel.org/r/20220411151620.129178-2-dave@stgolabs.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Bhupesh Sharma
Stephan Gerhold
Dmitry Baryshkov
Baruch Siach
Jami Kettunen
Sankeerth Billakanti
Vinod Koul
Luca Weiss
Yassine Oudjana
Krzysztof Kozlowski
Souradeep Chowdhury
Manikanta Pubbisetty
Rob Herring
Bob Pearson
Xiao Yang
Lv Ruyi
Davidlohr Bueso