| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The PLIC supports a fixed number of contexts (15872).
Each context has fixed register offsets in PLIC.
The number of contexts that we need to initialize depends on the privilege
modes supported by each hart. Therefore, this mapping between PLIC context
registers to hart privilege modes is platform specific, and is currently
supplied via device tree.
For example, canaan,k210 has the following mapping:
Context0: hart0 M-mode
Context1: hart0 S-mode
Context2: hart1 M-mode
Context3: hart1 S-mode
While sifive,fu540 has the following mapping:
Context0: hart0 M-mode
Context1: hart1 M-mode
Context2: hart1 S-mode
Because the number of contexts per hart is not fixed, the names
ENABLE_PER_HART and CONTEXT_PER_HART for the register offsets are quite
confusing and might mislead the reader to think that these are fixed
register offsets per hart.
Rename the offsets to more clearly highlight that these are per PLIC
context and not per hart.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220302131544.3166154-2-Niklas.Cassel@wdc.com
|
|
To initialize register NWL_DSI_IRQ_MASK, it's enough to write it
only once in function nwl_dsi_init_interrupts().
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220216085842.1973868-1-victor.liu@nxp.com
|
|
If the previous transfer didn't end with a command without DP_AUX_I2C_MOT,
the next read trasnfer will miss the first byte. But if the command in
previous transfer is requested with length 0, it's a no-op to anx7625
since it can't process this command. anx7625 requires the last command
to be read command with length > 0.
It's observed that if we clear the DP_AUX_I2C_MOT in read transfer, we
can still get correct data. Clear the read commands with DP_AUX_I2C_MOT
bit to fix this issue.
Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220217082224.1823916-1-hsinyi@chromium.org
|
|
The Surface 3 buttons are now handled by the generic soc_button_array
driver. As part of adding support to soc_button_array the ACPI code
now instantiates a platform_device rather then an i2c_client so there
no longer is an i2c_client for this driver to bind to.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220224110241.9613-3-hdegoede@redhat.com
|
|
The drivers/platform/surface/surface3_button.c code is alsmost a 1:1 copy
of the soc_button_array code.
The only big difference is that it binds to an i2c_client rather then to
a platform_device. The cause of this is the ACPI resources for the MSHW0028
device containing a bogus I2cSerialBusV2 resource which causes the kernel
to instantiate an i2c_client for it instead of a platform_device.
Add "MSHW0028" to the ignore_serial_bus_ids[] list in drivers/apci/scan.c,
so that a platform_device will be instantiated and add support for
the MSHW0028 HID to soc_button_array.
This fully replaces surface3_button, which will be removed in a separate
commit (since it binds to the now no longer created i2c_client it no
longer does anyyhing after this commit).
Note the MSHW0028 id is used by Microsoft to describe the tablet buttons on
both the Surface 3 and the Surface 3 Pro and the actual API/implementation
for the Surface 3 Pro is quite different. The changes in this commit should
not impact the separate surfacepro3_button driver:
1. Because of the bogus I2cSerialBusV2 resource problem that driver binds
to the acpi_device itself, so instantiating a platform_device instead of
an i2c_client does not matter.
2. The soc_button_array driver will not bind to the MSHW0028 device on
the Surface 3 Pro, because it has no GPIO resources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20220224110241.9613-2-hdegoede@redhat.com
|
|
There are a few sections in the driver which are not compatible with
PREEMPT_RT. They trigger warnings and can lead to deadlocks at runtime.
Disable the i915 driver on a PREEMPT_RT enabled kernel. This way
PREEMPT_RT itself can be enabled without needing to address the i915
issues first. The RT related patches are still in RT queue and will be
handled later.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YgqmfKhwU5spS069@linutronix.de
|
|
The ACPI tables for the codec setup on the Lenovo Yoga Tablet 2 830/1050
miss 2 things compared to their Windows (Lenovo Yoga Tablet 2 1051)
counterparts:
1. There is no CLKE ACPI method to enable output of the 32KHz PMU clock on
pin 6 of the SUS GPIO controller
2. The GPIOs used by the codec are not listed in the fwnode for the codec
Add pinctrl code to set the SUS6 pin mux manually and a gpio-lookup table
for the GPIOs to work around both issues.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220223133153.730337-6-hdegoede@redhat.com
|
|
These tablets' DSDT does not set acpi_gbl_reduced_hardware, so
acpi_power_off gets used as pm_power_off handler. Not setting
acpi_gbl_reduced_hardware may very well be correct for these tablets,
but acpi_power_off is broken on them.
Using acpi_power_off causes "poweroff" to hang hard. Requiring pressing
the powerbutton for 30 seconds *twice* followed by a normal 3 second
press to recover.
Avoid this by overriding the global pm_power_off handler to do
an EFI poweroff, which does work, instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220223133153.730337-5-hdegoede@redhat.com
|
|
The Lenovo Yoga Tablet 2 series comes in 4 versions: 830F, 830L, 1050F and
1050L. The F postfix indicates a wifi only version and the L postfix
indicates a LTE version. The 830 models are 8" and the 1050 models are 10".
Despite there being 8" and 10" versions all models use the same mainboard,
with an identical BIOS and thus identical DMI strings, so support for all
4 models is added through a single DMI table entry.
As all devices dealt with in the x86-android-tablets modules, these are
x86 ACPI tablets which ships with Android x86 as factory OS.
The mainboard's DSDT contain a bunch of I2C devices which are not actually
there, causing various resource conflicts. Enumeration of these is skipped
through the acpi_quirk_skip_i2c_client_enumeration().
Add support for manually instantiating the I2C devices which are
actually present on this tablet by adding the necessary device info to
the x86-android-tablets module.
This has been tested on a 830F and a 1050L tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220223133153.730337-4-hdegoede@redhat.com
|
|
Sometimes IRQs used by GPIOs in direct-IRQ mode are already registered
because they are used as ACPI "Interrupt () {}" resource for one of the
many bogus I2C devices present in the broken DSDTs of Android x86 tablets.
This is an issue if the existing (bogus) ACPI resource uses different
trigger settings then what is being requested, leading to an -EBUSY
error return of acpi_register_gsi().
Fix this by calling acpi_unregister_gsi() first, so that
the acpi_register_gsi() is allowed to change the trigger settings.
In cases where the GSI has not been registered yet
the acpi_unregister_gsi() is a no-op.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220223133153.730337-3-hdegoede@redhat.com
|
|
|
|
Instead of having quirks for systems that have a second fan it would
be nice to detect this setup.
Unfortunately, confirmed by the Lenovo FW team, there is no way to
retrieve this information from the EC or BIOS. Recommendation was to
attempt to read the fan and if successful then assume a 2nd fan is
present.
The fans are also supposed to spin up on boot for some time, so in
theory we could check for a speed > 0. In testing this seems to hold
true but as I couldn't test on all platforms I've avoided implementing
this. It also breaks for the corner case where you load the module
once the fans are idle.
Tested on P1G4, P1G3, X1C9 and T14 (no fans) and it works correctly.
For the platforms with dual fans where it was confirmed to work I have
removed the quirks. Potentially this could be done for all platforms
but I've left untested platforms in for now. On these platforms the
fans will be enabled and then detected - so no impact.
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Link: https://lore.kernel.org/r/20220222185137.4325-1-markpearson@lenovo.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This documentation for amd_hsmp driver explains how to use the
device interface.
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20220222050501.18789-2-nchatrad@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Recent Fam19h EPYC server line of processors from AMD support system
management functionality via HSMP (Host System Management Port) interface.
The Host System Management Port (HSMP) is an interface to provide
OS-level software with access to system management functions via a
set of mailbox registers.
More details on the interface can be found in chapter
"7 Host System Management Port (HSMP)" of the following PPR
https://www.amd.com/system/files/TechDocs/55898_B1_pub_0.50.zip
This patch adds new amd_hsmp module under the drivers/platforms/x86/
which creates miscdevice with an IOCTL interface to the user space.
/dev/hsmp is for running the hsmp mailbox commands.
Signed-off-by: Suma Hegde <suma.hegde@amd.com>
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Reviewed-by: Carlos Bilbao <carlos.bilbao@amd.com>
Acked-by: Song Liu <song@kernel.org>
Reviewed-by: Nathan Fontenot <nathan.fontenot@amd.com>
Link: https://lore.kernel.org/r/20220222050501.18789-1-nchatrad@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The battery on the 2nd hand Surface 3 which I recently bought appears to
not have a serial number programmed in. This results in any I2C reads from
the registers containing the serial number failing with an I2C NACK.
This was causing mshw0011_bix() to fail causing the battery readings to
not work at all.
Ignore EREMOTEIO (I2C NACK) errors when retrieving the serial number and
continue with an empty serial number to fix this.
Fixes: b1f81b496b0d ("platform/x86: surface3_power: MSHW0011 rev-eng implementation")
BugLink: https://github.com/linux-surface/linux-surface/issues/608
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220224101848.7219-1-hdegoede@redhat.com
|
|
commit 59348401ebed ("platform/x86: amd-pmc: Add special handling for
timer based S0i3 wakeup") adds support for using another platform timer
in lieu of the RTC which doesn't work properly on some systems. This path
was validated and worked well before submission. During the 5.16-rc1 merge
window other patches were merged that caused this to stop working properly.
When this feature was used with 5.16-rc1 or later some OEM laptops with the
matching firmware requirements from that commit would shutdown instead of
program a timer based wakeup.
This was bisected to commit 8d89835b0467 ("PM: suspend: Do not pause
cpuidle in the suspend-to-idle path"). This wasn't supposed to cause any
negative impacts and also tested well on both Intel and ARM platforms.
However this changed the semantics of when CPUs are allowed to be in the
deepest state. For the AMD systems in question it appears this causes a
firmware crash for timer based wakeup.
It's hypothesized to be caused by the `amd-pmc` driver sending `OS_HINT`
and all the CPUs going into a deep state while the timer is still being
programmed. It's likely a firmware bug, but to avoid it don't allow setting
CPUs into the deepest state while using CZN timer wakeup path.
If later it's discovered that this also occurs from "regular" suspends
without a timer as well or on other silicon, this may be later expanded to
run in the suspend path for more scenarios.
Cc: stable@vger.kernel.org # 5.16+
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/linux-acpi/BL1PR12MB51570F5BD05980A0DCA1F3F4E23A9@BL1PR12MB5157.namprd12.prod.outlook.com/T/#mee35f39c41a04b624700ab2621c795367f19c90e
Fixes: 8d89835b0467 ("PM: suspend: Do not pause cpuidle in the suspend-to-idle path")
Fixes: 23f62d7ab25b ("PM: sleep: Pause cpuidle later and resume it earlier during system transitions")
Fixes: 59348401ebed ("platform/x86: amd-pmc: Add special handling for timer based S0i3 wakeup")
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220223175237.6209-1-mario.limonciello@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
SD spec definition:
"Host provides at least 74 Clocks before issuing first command"
After 1ms for the voltage stable then start issuing the Clock signals
if POWER STATE is
MMC_POWER_OFF to MMC_POWER_UP to issue Clock signal to card
MMC_POWER_UP to MMC_POWER_ON to stop issuing signal to card
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/1badf10aba764191a1a752edcbf90389@realtek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
On ARM64 Hyper-V guests, SPIs are used for the interrupts of virtual PCI
devices, and SPIs can be managed directly via GICD registers. Therefore
the retarget interrupt hypercall is not needed on ARM64.
An arch-specific interface hv_arch_irq_unmask() is introduced to handle
the architecture level differences on this. For x86, the behavior
remains unchanged, while for ARM64 no hypercall is invoked when
unmasking an irq for virtual PCI devices.
Link: https://lore.kernel.org/r/20220217034525.1687678-1-boqun.feng@gmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
|
|
It's valid to use the PCA955x devices just for GPIOs and not for LEDs.
In this case, as PCA955X_TYPE_GPIO is now equivalent to
PCA955X_TYPE_NONE, remove the test for whether we have any child nodes
specified in the devicetree.
A consequence of this is it's now possible to bind the driver to a
PCA955x device when dynamically instantiated through the I2C subsystem's
`new_device` interface.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
The devicetree binding allows specifying which pins are GPIO vs LED.
Limiting the instantiated gpiochip to just these pins as the driver
currently does requires an arbitrary mapping between pins and GPIOs, but
such a mapping is not implemented by the driver. As a result,
specifying GPIOs in such a way that they don't map 1-to-1 to pin indexes
does not function as expected.
Establishing such a mapping is more complex than not and even if we did,
doing so leads to a slightly hairy userspace experience as the behaviour
of the PCA955x gpiochip would depend on how the pins are assigned in the
devicetree. Instead, always expose all pins via the gpiochip to provide
a stable interface and track which pins are in use.
Specifying a pin as `type = <PCA955X_TYPE_GPIO>;` in the devicetree
becomes a no-op.
I've assessed the impact of this change by looking through all of the
affected devicetrees as of the tag leds-5.15-rc1:
```
$ git grep -l 'pca955[0123]' $(find . -name dts -type d)
arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts
arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts
arch/arm/boot/dts/aspeed-bmc-opp-swift.dts
arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts
arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts
```
These are all IBM-associated platforms. I've analysed both the
devicetrees and schematics where necessary to determine whether any
systems hit the hazard of the current broken behaviour. For the most
part, the systems specify the pins as either all LEDs or all GPIOs, or
at least do so in a way such that the broken behaviour isn't exposed.
The main counter-point to this observation is the Everest system whose
devicetree describes a large number of PCA955x devices and in some cases
has pin assignments that hit the hazard. However, there does not seem to
be any use of the affected GPIOs in the userspace associated with
Everest.
Regardless, any use of the hazardous GPIOs in Everest is already broken,
so let's fix the interface and then fix any already broken userspace
with it.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
|
|
change 'cannel' to 'channel'
Signed-off-by: Sunrisepeak <speakshen@163.com>
Link: https://lore.kernel.org/r/20220227145204.16600-1-speakshen@163.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
PCM buffers might be allocated dynamically when the buffer
preallocation failed or a larger buffer is requested, and it's not
guaranteed that substream->dma_buffer points to the actually used
buffer. The driver needs to refer to substream->runtime->dma_addr
instead for the buffer address.
Signed-off-by: Zhen Ni <nizhen@uniontech.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220302074241.30469-1-nizhen@uniontech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The ifindex doesn't have to be unique for multiple network namespaces on
the same machine.
$ ip netns add test1
$ ip -net test1 link add dummy1 type dummy
$ ip netns add test2
$ ip -net test2 link add dummy2 type dummy
$ ip -net test1 link show dev dummy1
6: dummy1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 96:81:55:1e:dd:85 brd ff:ff:ff:ff:ff:ff
$ ip -net test2 link show dev dummy2
6: dummy2: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 5a:3c:af:35:07:c3 brd ff:ff:ff:ff:ff:ff
But the batman-adv code to walk through the various layers of virtual
interfaces uses this assumption because dev_get_iflink handles it
internally and doesn't return the actual netns of the iflink. And
dev_get_iflink only documents the situation where ifindex == iflink for
physical devices.
But only checking for dev->netdev_ops->ndo_get_iflink is also not an option
because ipoib_get_iflink implements it even when it sometimes returns an
iflink != ifindex and sometimes iflink == ifindex. The caller must
therefore make sure itself to check both netns and iflink + ifindex for
equality. Only when they are equal, a "physical" interface was detected
which should stop the traversal. On the other hand, vxcan_get_iflink can
also return 0 in case there was currently no valid peer. In this case, it
is still necessary to stop.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Fixes: 5ed4a460a1d3 ("batman-adv: additional checks for virtual interfaces on top of WiFi")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
If an invalid option value is used with "printk.devkmsg=<value>",
it is silently ignored.
If a valid option value is used, it is honored but the wrong return
value (0) is used, indicating that the command line option had an
error and was not handled. This string is not added to init's
environment strings due to init/main.c::unknown_bootoption()
checking for a '.' in the boot option string and then considering
that string to be an "Unused module parameter".
Print a warning message if a bad option string is used.
Always return 1 from the __setup handler to indicate that the command
line option has been handled.
Fixes: 750afe7babd1 ("printk: add kernel parameter to control writes to /dev/kmsg")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Cc: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: John Ogness <john.ogness@linutronix.de>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20220228220556.23484-1-rdunlap@infradead.org
|
|
There is no need to call dev_get_iflink multiple times for the same
net_device in batadv_get_real_netdevice. And since some of the
ndo_get_iflink callbacks are dynamic (for example via RCUs like in
vxcan_get_iflink), it could easily happen that the returned values are not
stable. The pre-checks before __dev_get_by_index are then of course bogus.
Fixes: 5ed4a460a1d3 ("batman-adv: additional checks for virtual interfaces on top of WiFi")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
There is no need to call dev_get_iflink multiple times for the same
net_device in batadv_is_on_batman_iface. And since some of the
.ndo_get_iflink callbacks are dynamic (for example via RCUs like in
vxcan_get_iflink), it could easily happen that the returned values are not
stable. The pre-checks before __dev_get_by_index are then of course bogus.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The error message "Cannot find parent device" was shown for users of
macvtap (on batadv devices) whenever the macvtap was moved to a different
netns. This happens because macvtap doesn't provide an implementation for
rtnl_link_ops->get_link_net.
The situation for which this message is printed is actually not an error
but just a warning that the optional sanity check was skipped. So demote
the message from error to warning and adjust the text to better explain
what happened.
Reported-by: Leonardo Mörlein <freifunk@irrelefant.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The commit d2a8ebbf8192 ("kernel.h: split out container_of() and
typeof_member() macros") introduced a new header for the container_of
related macros from (previously) linux/kernel.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Kernel messages produced during runtime PM can cause a never-ending cycle
because user space utilities (e.g. journald or rsyslog) write the messages
back to storage, causing runtime resume, more messages, and so on.
Messages that tell of things that are expected to happen, are arguably
unnecessary, so suppress them.
UFS driver messages are changes to from dev_err() to dev_dbg() which means
they will not display unless activated by dynamic debug of building with
-DDEBUG.
sdev->silence_suspend is set to skip messages from sd_suspend_common()
"Synchronizing SCSI cache", "Stopping disk" and scsi_report_sense()
"Power-on or device reset occurred" message (Note, that message appears
when the LUN is accessed after runtime PM, not during runtime PM)
Example messages from Ubuntu 21.10:
$ dmesg | tail
[ 1620.380071] ufshcd 0000:00:12.5: ufshcd_print_pwr_info:[RX, TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate = 0
[ 1620.408825] ufshcd 0000:00:12.5: ufshcd_print_pwr_info:[RX, TX]: gear=[4, 4], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
[ 1620.409020] ufshcd 0000:00:12.5: ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, actvIccLevel=0
[ 1620.409524] sd 0:0:0:0: Power-on or device reset occurred
[ 1622.938794] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 1622.939184] ufs_device_wlun 0:0:0:49488: Power-on or device reset occurred
[ 1625.183175] ufshcd 0000:00:12.5: ufshcd_print_pwr_info:[RX, TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate = 0
[ 1625.208041] ufshcd 0000:00:12.5: ufshcd_print_pwr_info:[RX, TX]: gear=[4, 4], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
[ 1625.208311] ufshcd 0000:00:12.5: ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, actvIccLevel=0
[ 1625.209035] sd 0:0:0:0: Power-on or device reset occurred
Note for stable: depends on patch "scsi: core: sd: Add silence_suspend flag
to suppress some PM messages".
Link: https://lore.kernel.org/r/20220228113652.970857-3-adrian.hunter@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Kernel messages produced during runtime PM can cause a never-ending cycle
because user space utilities (e.g. journald or rsyslog) write the messages
back to storage, causing runtime resume, more messages, and so on.
Messages that tell of things that are expected to happen are arguably
unnecessary, so add a flag to suppress them. This flag is used by the UFS
driver.
Link: https://lore.kernel.org/r/20220228113652.970857-2-adrian.hunter@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We only need the rport structure for lpfc_chk_tgt_mapped().
Link: https://lore.kernel.org/r/20220301143718.40913-6-hare@suse.de
Cc: James Smart <james.smart@broadcom.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Instead of passing in a scsi_cmnd we should be using the rport; we already
have the target and LUN ID as parameters, so there's no need to pass the
scsi_cmnd too.
Link: https://lore.kernel.org/r/20220301143718.40913-5-hare@suse.de
Cc: James Smart <james.smart@broadcom.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use fc_block_rport() instead of fc_block_scsi_eh() as the SCSI command will
be removed as argument for SCSI EH functions.
Link: https://lore.kernel.org/r/20220301143718.40913-4-hare@suse.de
Cc: James Smart <james.smart@broadcom.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The default SCSI EH action for a non-existing EH callback is to return
FAILED, so having a callback just returning FAILED is pointless.
Link: https://lore.kernel.org/r/20220301143718.40913-3-hare@suse.de
Cc: James Smart <james.smart@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
lpfc_bus_reset_handler() is really just a loop calling
lpfc_target_reset_handler() over all targets, which is what the error
handler will be doing anyway.
Link: https://lore.kernel.org/r/20220301143718.40913-2-hare@suse.de
Cc: James Smart <james.smart@broadcom.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During the process of driver probing, the probe function should return < 0
for failure, otherwise the kernel will treat value >= 0 as success.
Set 'err' to the error value returned by dma_set_mask() in case of failure.
Link: https://lore.kernel.org/r/1646060055-11361-1-git-send-email-zheyuma97@gmail.com
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the workqueue code was created it didn't allow variable args so we
have been using a temp buffer. Drop that.
Link: https://lore.kernel.org/r/20220226230435.38733-7-michael.christie@oracle.com
Reviewed-by: Chris Leech <cleech@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the session workqueue for recovery and unbinding. If there are delays
during device blocking/cleanup then it will no longer affect other
sessions.
Link: https://lore.kernel.org/r/20220226230435.38733-6-michael.christie@oracle.com
Reviewed-by: Chris Leech <cleech@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We currently allocate a workqueue per host and only use it for removing the
target. For the session per host case we could be using this workqueue to
be able to do recoveries (block, unblock, timeout handling) in parallel. To
also allow offload drivers to do their session recoveries in parallel, this
drops the per host workqueue and replaces it with a per session one.
Link: https://lore.kernel.org/r/20220226230435.38733-5-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
qla4xxx does not use iscsi_scan_finished() anymore so remove it.
Link: https://lore.kernel.org/r/20220226230435.38733-4-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the iSCSI class was added upstream, blocking a queue was fast because
it just set some flag bits and didn't handle I/O that was in the process of
being sent to the driver. That's no longer the case so blocking a queue is
expensive and we can end up with a backlog of blocks by the time we have
relogged in and are trying to start the queues.
For the session unblock case, this has try to cancel the block and recovery
work in case they are still queued so we can avoid unneeded queue
manipulations. For removal, we also now try to cancel all the recovery
related works since a couple lines down we will set the session and device
state so running those functions are not necessary.
Link: https://lore.kernel.org/r/20220226230435.38733-3-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If the user sets the iscsi_eh_timer_workq/iscsi_eh workqueue's max_active
to greater than 1, the recovery_work could be running when
__iscsi_unblock_session() runs. The cancel_delayed_work() will then not
wait for the running work and we can race where we end up with the wrong
session state and scsi_device state set.
This replaces the cancel_delayed_work() with the sync version.
Link: https://lore.kernel.org/r/20220226230435.38733-2-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In the original FPIN commit, stats were incremented by the event_count.
Event_count is the minimum # of events that must occur before an FPIN is
sent. Thus, its not the actual number of events, and could be significantly
off (too low) as it doesn't reflect anything not reported. Rather than
attempt to count events, have the statistic count how many FPINS cross the
threshold and were reported.
Link: https://lore.kernel.org/r/20220301175536.60250-1-jsmart2021@gmail.com
Fixes: 3dcfe0de5a97 ("scsi: fc: Parse FPIN packets and update statistics")
Cc: <stable@vger.kernel.org> # v5.11+
Cc: Shyam Sundar <ssundar@marvell.com>
Cc: Nilesh Javali <njavali@marvell.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Sparse throws a warning about context imbalance ("different lock contexts
for basic block") in sas_form_port() as it gets confused with the fact that
a port is locked within one of the two search loops and unlocked afterward
outside of the search loops once the phy is added to the port. Since this
code is not easy to follow, improve it by factoring out the code adding the
phy to the port once the port is locked into the helper function
sas_form_port_add_phy(). This helper can then be called directly within the
port search loops, avoiding confusion and clearing the sparse warning.
Link: https://lore.kernel.org/r/20220228094857.557329-1-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Before these changes elan_suspend() would only disable the regulator
when device_may_wakeup() returns false; whereas elan_resume() would
unconditionally enable it, leading to an enable count imbalance when
device_may_wakeup() returns true.
This triggers the "WARN_ON(regulator->enable_count)" in regulator_put()
when the elan_i2c driver gets unbound, this happens e.g. with the
hot-plugable dock with Elan I2C touchpad for the Asus TF103C 2-in-1.
Fix this by making the regulator_enable() call also be conditional
on device_may_wakeup() returning false.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131135436.29638-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
elan_disable_power() is called conditionally on suspend, where as
elan_enable_power() is always called on resume. This leads to
an imbalance in the regulator's enable count.
Move the regulator_[en|dis]able() calls out of elan_[en|dis]able_power()
in preparation of fixing this.
No functional changes intended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131135436.29638-1-hdegoede@redhat.com
[dtor: consolidate elan_[en|dis]able() into elan_set_power()]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When trying to add a histogram against an event with the "cpu" field, it
was impossible due to "cpu" being a keyword to key off of the running CPU.
So to fix this, it was changed to "common_cpu" to match the other generic
fields (like "common_pid"). But since some scripts used "cpu" for keying
off of the CPU (for events that did not have "cpu" as a field, which is
most of them), a backward compatibility trick was added such that if "cpu"
was used as a key, and the event did not have "cpu" as a field name, then
it would fallback and switch over to "common_cpu".
This fix has a couple of subtle bugs. One was that when switching over to
"common_cpu", it did not change the field name, it just set a flag. But
the code still found a "cpu" field. The "cpu" field is used for filtering
and is returned when the event does not have a "cpu" field.
This was found by:
# cd /sys/kernel/tracing
# echo hist:key=cpu,pid:sort=cpu > events/sched/sched_wakeup/trigger
# cat events/sched/sched_wakeup/hist
Which showed the histogram unsorted:
{ cpu: 19, pid: 1175 } hitcount: 1
{ cpu: 6, pid: 239 } hitcount: 2
{ cpu: 23, pid: 1186 } hitcount: 14
{ cpu: 12, pid: 249 } hitcount: 2
{ cpu: 3, pid: 994 } hitcount: 5
Instead of hard coding the "cpu" checks, take advantage of the fact that
trace_event_field_field() returns a special field for "cpu" and "CPU" if
the event does not have "cpu" as a field. This special field has the
"filter_type" of "FILTER_CPU". Check that to test if the returned field is
of the CPU type instead of doing the string compare.
Also, fix the sorting bug by testing for the hist_field flag of
HIST_FIELD_FL_CPU when setting up the sort routine. Otherwise it will use
the special CPU field to know what compare routine to use, and since that
special field does not have a size, it returns tracing_map_cmp_none.
Cc: stable@vger.kernel.org
Fixes: 1e3bac71c505 ("tracing/histogram: Rename "cpu" to "common_cpu"")
Reported-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
This header is empty now except for an include of <linux/blk-mq.h>, so
remove it.
Link: https://lore.kernel.org/r/20220224175552.988286-9-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Let submitters initialize the scmd->allowed field directly instead of
indirecting through struct scsi_request and remove the now superfluous
structure.
Link: https://lore.kernel.org/r/20220224175552.988286-8-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Prepare for removing the scsi_request structure by moving the result field
to struct scsi_cmnd.
Link: https://lore.kernel.org/r/20220224175552.988286-7-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
Niklas Cassel
Liu Ying
Hsin-Yi Wang
Hans de Goede
Sebastian Andrzej Siewior
Mark Pearson
Naveen Krishna Chatradhi
Suma Hegde
Mario Limonciello
Ricky WU
Boqun Feng
Andrew Jeffery
Sunrisepeak
Zhen Ni
Sven Eckelmann
Randy Dunlap
Adrian Hunter
Hannes Reinecke
Zheyu Ma
Mike Christie
James Smart
Damien Le Moal
Steven Rostedt (Google)
Christoph Hellwig